In order to be more confident about an on-going interactive session, we
increment pingpong count by 1 for every interactive transaction and we
adjust TCP_PINGPONG_THRESH to 3.
This means, we only consider a session in pingpong mode after we see 3
interactive transactions, and start to activate delayed acks in quick
ack mode.
And in order to not over-count the credits, we only increase pingpong
count for the first packet sent in response for the previous received
packet.
This is mainly to prevent delaying the ack immediately after some
handshake protocol but no real interactive traffic pattern afterwards.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using pingpong as a single bit information, we refactor the
code to treat it as a counter. When interactive session is detected,
we set pingpong count to TCP_PINGPONG_THRESH. And when pingpong count
is >= TCP_PINGPONG_THRESH, we consider the session in pingpong mode.
This patch is a pure refactor and sets foundation for the next patch.
This patch itself does not change any pingpong logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept MSG_ZEROCOPY in all the TCP states that allow sendmsg. Remove
the explicit check for ESTABLISHED and CLOSE_WAIT states.
This requires correctly handling zerocopy state (uarg, sk_zckey) in
all paths reachable from other TCP states. Such as the EPIPE case
in sk_stream_wait_connect, which a sendmsg() in incorrect state will
now hit. Most paths are already safe.
Only extension needed is for TCP Fastopen active open. This can build
an skb with data in tcp_send_syn_data. Pass the uarg along with other
fastopen state, so that this skb also generates a zerocopy
notification on release.
Tested with active and passive tcp fastopen packetdrill scripts at
1747eef03d
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously when the sender fails to send (original) data packet or
window probes due to congestion in the local host (e.g. throttling
in qdisc), it'll retry within an RTO or two up to 500ms.
In low-RTT networks such as data-centers, RTO is often far below
the default minimum 200ms. Then local host congestion could trigger
a retry storm pouring gas to the fire. Worse yet, the probe counter
(icsk_probes_out) is not properly updated so the aggressive retry
may exceed the system limit (15 rounds) until the packet finally
slips through.
On such rare events, it's wise to retry more conservatively
(500ms) and update the stats properly to reflect these incidents
and follow the system limit. Note that this is consistent with
the behaviors when a keep-alive probe or RTO retry is dropped
due to local congestion.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP socket's retrans_stamp is not set if the
retransmission has failed to send. As a result if a socket is
experiencing local issues to retransmit packets, determining when
to abort a socket is complicated w/o knowning the starting time of
the recovery since retrans_stamp may remain zero.
This complication causes sub-optimal behavior that TCP may use the
latest, instead of the first, retransmission time to compute the
elapsed time of a stalling connection due to local issues. Then TCP
may disrecard TCP retries settings and keep retrying until it finally
succeed: not a good idea when the local host is already strained.
The simple fix is to always timestamp the start of a recovery.
It's worth noting that retrans_stamp is also used to compare echo
timestamp values to detect spurious recovery. This patch does
not break that because retrans_stamp is still later than when the
original packet was sent.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP skbs are not always timestamped if the transmission
failed due to memory or other local issues. This makes deciding
when to abort a socket tricky and complicated because the first
unacknowledged skb's timestamp may be 0 on TCP timeout.
The straight-forward fix is to always timestamp skb on every
transmission attempt. Also every skb retransmission needs to be
flagged properly to avoid RTT under-estimation. This can happen
upon receiving an ACK for the original packet and the a previous
(spurious) retransmission has failed.
It's worth noting that this reverts to the old time-stamping
style before commit 8c72c65b42 ("tcp: update skb->skb_mstamp more
carefully") which addresses a problem in computing the elapsed time
of a stalled window-probing socket. The problem will be addressed
differently in the next patches with a simpler approach.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit f9bfe4e6a9 ("tcp: lack of available data can also cause
TSO defer") we moved the test in tcp_tso_should_defer() for packets
with a FIN flag, and we mentioned that the same would be done
later for EOR flag.
Both flags should be handled at the same time, after all other
heuristics have been considered. They both mean that no more bytes
can be added to this skb by an application.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_tso_should_defer() can return true in three different cases :
1) We are cwnd-limited
2) We are rwnd-limited
3) We are application limited.
Neal pointed out that my recent fix went too far, since
it assumed that if we were not in 1) case, we must be rwnd-limited
Fix this by properly populating the is_cwnd_limited and
is_rwnd_limited booleans.
After this change, we can finally move the silly check for FIN
flag only for the application-limited case.
The same move for EOR bit will be handled in net-next,
since commit 1c09f7d073 ("tcp: do not try to defer skbs
with eor mark (MSG_EOR)") is scheduled for linux-4.21
Tested by running 200 concurrent netperf -t TCP_RR -- -r 60000,100
and checking none of them was rwnd_limited in the chrono_stat
output from "ss -ti" command.
Fixes: 41727549de ("tcp: Do not underestimate rwnd_limited")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP loss probe timer may fire when the retranmission queue is empty but
has a non-zero tp->packets_out counter. tcp_send_loss_probe will call
tcp_rearm_rto which triggers NULL pointer reference by fetching the
retranmission queue head in its sub-routines.
Add a more detailed warning to help catch the root cause of the inflight
accounting inconsistency.
Reported-by: Rafael Tinoco <rafael.tinoco@linaro.org>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If available rwnd is too small, tcp_tso_should_defer()
can decide it is worth waiting before splitting a TSO packet.
This really means we are rwnd limited.
Fixes: 5615f88614 ("tcp: instrument how long TCP is limited by receive window")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the SNMP counter LINUX_MIB_TCPRETRANSFAIL is not counting
the TSO/GSO properly on failed retransmission. This patch fixes that.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most linux hosts never setup TCP MD5 keys. We can avoid a
cache line miss (accessing tp->md5ig_info) on RX and TX
using a jump label.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove the loop and conditional branches
and compute wscale efficiently thanks to ilog2()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jean-Louis reported a TCP regression and bisected to recent SACK
compression.
After a loss episode (receiver not able to keep up and dropping
packets because its backlog is full), linux TCP stack is sending
a single SACK (DUPACK).
Sender waits a full RTO timer before recovering losses.
While RFC 6675 says in section 5, "Algorithm Details",
(2) If DupAcks < DupThresh but IsLost (HighACK + 1) returns true --
indicating at least three segments have arrived above the current
cumulative acknowledgment point, which is taken to indicate loss
-- go to step (4).
...
(4) Invoke fast retransmit and enter loss recovery as follows:
there are old TCP stacks not implementing this strategy, and
still counting the dupacks before starting fast retransmit.
While these stacks probably perform poorly when receivers implement
LRO/GRO, we should be a little more gentle to them.
This patch makes sure we do not enable SACK compression unless
3 dupacks have been sent since last rcv_nxt update.
Ideally we should even rearm the timer to send one or two
more DUPACK if no more packets are coming, but that will
be work aiming for linux-4.21.
Many thanks to Jean-Louis for bisecting the issue, providing
packet captures and testing this patch.
Fixes: 5d9f4262b7 ("tcp: add SACK compression")
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FQ pacing guarantees that paced packets queued by one flow do not
add head-of-line blocking for other flows.
After TCP GSO conversion, increasing limit_output_bytes to 1 MB is safe,
since this maps to 16 skbs at most in qdisc or device queues.
(or slightly more if some drivers lower {gso_max_segs|size})
We still can queue at most 1 ms worth of traffic (this can be scaled
by wifi drivers if they need to)
Tested:
# ethtool -c eth0 | egrep "tx-usecs:|tx-frames:" # 40 Gbit mlx4 NIC
tx-usecs: 16
tx-frames: 16
# tc qdisc replace dev eth0 root fq
# for f in {1..10};do netperf -P0 -H lpaa24,6 -o THROUGHPUT;done
Before patch:
27711
26118
27107
27377
27712
27388
27340
27117
27278
27509
After patch:
37434
36949
36658
36998
37711
37291
37605
36659
36544
37349
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_tso_should_defer() first heuristic is to not defer
if last send is "old enough".
Its current implementation uses jiffies and its low granularity.
TSO autodefer performance should not rely on kernel HZ :/
After EDT conversion, we have state variables in nanoseconds that
can allow us to properly implement the heuristic.
This patch increases TSO chunk sizes on medium rate flows,
especially when receivers do not use GRO or similar aggregation.
It also reduces bursts for HZ=100 or HZ=250 kernels, making TCP
behavior more uniform.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_tso_should_defer() last step tries to check if the probable
next ACK packet is coming in less than half rtt.
Problem is that the head->tstamp might be in the future,
so we need to use signed arithmetics to avoid overflows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications using MSG_EOR are giving a strong hint to TCP stack :
Subsequent sendmsg() can not append more bytes to skbs having
the EOR mark.
Do not try to TSO defer suchs skbs, there is really no hope.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With EDT model, SRTT no longer is inflated by pacing delays.
This means that RTO and some other xmit timers might be setup
incorrectly. This is particularly visible with either :
- Very small enforced pacing rates (SO_MAX_PACING_RATE)
- Reduced rto (from the default 200 ms)
This can lead to TCP flows aborts in the worst case,
or spurious retransmits in other cases.
For example, this session gets far more throughput
than the requested 80kbit :
$ netperf -H 127.0.0.2 -l 100 -- -q 10000
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 127.0.0.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
540000 262144 262144 104.00 2.66
With the fix :
$ netperf -H 127.0.0.2 -l 100 -- -q 10000
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 127.0.0.2 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
540000 262144 262144 104.00 0.12
EDT allows for better control of rtx timers, since TCP has
a better idea of the earliest departure time of each skb
in the rtx queue. We only have to eventually add to the
timer the difference of the EDT time with current time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported the following warning triggered while running CRIU tests:
tcp_clean_rtx_queue()
...
last_ackt = tcp_skb_timestamp_us(skb);
WARN_ON_ONCE(last_ackt == 0);
This is caused by 5f6188a800 ("tcp: do not change tcp_wstamp_ns
in tcp_mstamp_refresh"), as we end up having skbs in retransmit queue
with a zero skb->skb_mstamp_ns field.
We could fix this bug in different ways, like making sure
tp->tcp_wstamp_ns is not zero at socket creation, but as Neal pointed
out, we also do not want that pacing status of a repaired socket
could push tp->tcp_wstamp_ns far ahead in the future.
So we prefer changing tcp_write_xmit() to not call tcp_update_skb_after_send()
and instead do what is requested by TCP_REPAIR logic.
Fixes: 5f6188a800 ("tcp: do not change tcp_wstamp_ns in tcp_mstamp_refresh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP implements its own pacing (when no fq packet scheduler is used),
it is arming high resolution timer after a packet is sent.
But in many cases (like TCP_RR kind of workloads), this high resolution
timer expires before the application attempts to write the following
packet. This overhead also happens when the flow is ACK clocked and
cwnd limited instead of being limited by the pacing rate.
This leads to extra overhead (high number of IRQ)
Now tcp_wstamp_ns is reserved for the pacing timer only
(after commit "tcp: do not change tcp_wstamp_ns in tcp_mstamp_refresh"),
we can setup the timer only when a packet is about to be sent,
and if tcp_wstamp_ns is in the future.
This leads to a ~10% performance increase in TCP_RR workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit fefa569a9d ("net_sched: sch_fq: account for schedule/timers
drifts") we added a mitigation for scheduling jitter in fq packet scheduler.
This patch does the same in TCP stack, now it is using EDT model.
Note that this mitigation is valid for both external (fq packet scheduler)
or internal TCP pacing.
This uses the same strategy than the above commit, allowing
a time credit of half the packet currently sent.
Consider following case :
An skb is sent, after an idle period of 300 usec.
The air-time (skb->len/pacing_rate) is 500 usec
Instead of setting the pacing timer to now+500 usec,
it will use now+min(500/2, 300) -> now+250usec
This is like having a token bucket with a depth of half
an skb.
Tested:
tc qdisc replace dev eth0 root pfifo_fast
Before
netperf -P0 -H remote -- -q 1000000000 # 8000Mbit
540000 262144 262144 10.00 7710.43
After :
netperf -P0 -H remote -- -q 1000000000 # 8000 Mbit
540000 262144 262144 10.00 7999.75 # Much closer to 8000Mbit target
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_pacing_rate has beed introduced as a u32 field in 2013,
effectively limiting per flow pacing to 34Gbit.
We believe it is time to allow TCP to pace high speed flows
on 64bit hosts, as we now can reach 100Gbit on one TCP flow.
This patch adds no cost for 32bit kernels.
The tcpi_pacing_rate and tcpi_max_pacing_rate were already
exported as 64bit, so iproute2/ss command require no changes.
Unfortunately the SO_MAX_PACING_RATE socket option will stay
32bit and we will need to add a new option to let applications
control high pacing rates.
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 1787144 10.246.9.76:49992 10.246.9.77:36741
timer:(on,003ms,0) ino:91863 sk:2 <->
skmem:(r0,rb540000,t66440,tb2363904,f605944,w1822984,o0,bl0,d0)
ts sack bbr wscale:8,8 rto:201 rtt:0.057/0.006 mss:1448
rcvmss:536 advmss:1448
cwnd:138 ssthresh:178 bytes_acked:256699822585 segs_out:177279177
segs_in:3916318 data_segs_out:177279175
bbr:(bw:31276.8Mbps,mrtt:0,pacing_gain:1.25,cwnd_gain:2)
send 28045.5Mbps lastrcv:73333
pacing_rate 38705.0Mbps delivery_rate 22997.6Mbps
busy:73333ms unacked:135 retrans:0/157 rcv_space:14480
notsent:2085120 minrtt:0.013
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In EDT design, I made the mistake of using tcp_wstamp_ns
to store the last tcp_clock_ns() sample and to store the
pacing virtual timer.
This causes major regressions at high speed flows.
Introduce tcp_clock_cache to store last tcp_clock_ns().
This is needed because some arches have slow high-resolution
kernel time service.
tcp_wstamp_ns is only updated when a packet is sent.
Note that we can remove tcp_mstamp in the future since
tcp_mstamp is essentially tcp_clock_cache/1000, so the
apparent socket size increase is temporary.
Fixes: 9799ccb0e9 ("tcp: add tcp_wstamp_ns socket field")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP initial receive buffer is ~87KB by default and
the initial receive window is ~29KB (20 MSS). This patch changes
the two numbers to 128KB and ~64KB (rounding down to the multiples
of MSS) respectively. The patch also simplifies the calculations s.t.
the two numbers are directly controlled by sysctl tcp_rmem[1]:
1) Initial receiver buffer budget (sk_rcvbuf): while this should
be configured via sysctl tcp_rmem[1], previously tcp_fixup_rcvbuf()
always override and set a larger size when a new connection
establishes.
2) Initial receive window in SYN: previously it is set to 20
packets if MSS <= 1460. The number 20 was based on the initial
congestion window of 10: the receiver needs twice amount to
avoid being limited by the receive window upon out-of-order
delivery in the first window burst. But since this only
applies if the receiving MSS <= 1460, connection using large MTU
(e.g. to utilize receiver zero-copy) may be limited by the
receive window.
With this patch TCP memory configuration is more straight-forward and
more properly sized to modern high-speed networks by default. Several
popular stacks have been announcing 64KB rwin in SYNs as well.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now TCP keeps track of tcp_wstamp_ns, recording the earliest
departure time of next packet, we can remove duplicate code
from tcp_internal_pacing()
This removes one ktime_get_tai_ns() call, and a divide.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP keeps track of tcp_wstamp_ns by itself, meaning sch_fq
no longer has to do it.
Thanks to this model, TCP can get more accurate RTT samples,
since pacing no longer inflates them.
This has the nice effect of removing some delays caused by FQ
quantum mechanism, causing inflated max/P99 latencies.
Also we might relax TCP Small Queue tight limits in the future,
since this new model allow TCP to build bigger batches, since
sch_fq (or a device with earliest departure time offload) ensure
these packets will be delivered on time.
Note that other protocols are not converted (they will probably
never be) so sch_fq has still support for SO_MAX_PACING_RATE
Tested:
Test showing FQ pacing quantum artifact for low-rate flows,
adding unexpected throttles for RPC flows, inflating max and P99 latencies.
The parameters chosen here are to show what happens typically when
a TCP flow has a reduced pacing rate (this can be caused by a reduced
cwin after few losses, or/and rtt above few ms)
MIBS="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
Before :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
19,82.78,5279,3825,482.02
After :
$ netperf -H 10.246.7.133 -t TCP_RR -Cc -T6,6 -- -q 2000000 -r 100,100 -o $MIBS
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.246.7.133 () port 0 AF_INET : first burst 0 : cpu bind
Minimum Latency Microseconds,Mean Latency Microseconds,Maximum Latency Microseconds,99th Percentile Latency Microseconds,Stddev Latency Microseconds
20,49.94,128,63,3.18
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch will use tcp_wstamp_ns to feed internal
TCP pacing timer, so switch to CLOCK_TAI to share same base.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch internal TCP skb->skb_mstamp to skb->skb_mstamp_ns,
from usec units to nsec units.
Do not clear skb->tstamp before entering IP stacks in TX,
so that qdisc or devices can implement pacing based on the
earliest departure time instead of socket sk->sk_pacing_rate
Packets are fed with tcp_wstamp_ns, and following patch
will update tcp_wstamp_ns when both TCP and sch_fq switch to
the earliest departure time mechanism.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP will soon provide earliest departure time on TX skbs.
It needs to track this in a new variable.
tcp_mstamp_refresh() needs to update this variable, and
became too big to stay an inline.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are few places where TCP reads skb->skb_mstamp expecting
a value in usec unit.
skb->tstamp (aka skb->skb_mstamp) will soon store CLOCK_TAI nsec value.
Add tcp_skb_timestamp_us() to provide proper conversion when needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/ipv4/tcp_output.c: In function 'tcp_collapse_retrans':
net/ipv4/tcp_output.c:2700:6: warning:
variable 'skb_size' set but not used [-Wunused-but-set-variable]
int skb_size, next_skb_size;
^
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new TCP stat to record the number of bytes retransmitted
(RFC4898 tcpEStatsPerfOctetsRetrans) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new TCP stat to record the number of bytes sent
(RFC4898 tcpEStatsPerfHCDataOctetsOut) and expose it in both tcp_info
(TCP_INFO) and opt_stats (SOF_TIMESTAMPING_OPT_STATS).
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).
Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.
The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and create helpers to send the special ACK in DCTCP.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After fixing the way DCTCP tracking delayed ACKs, the delayed-ACK
related callbacks are no longer needed
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes BBR use only the MSS (without any headers) to
calculate pacing rates when internal TCP-layer pacing is used.
This is necessary to achieve the correct pacing behavior in this case,
since tcp_internal_pacing() uses only the payload length to calculate
pacing delays.
Signed-off-by: Kevin Yang <yyd@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter tracks number of ACK packets that the host has not sent,
thanks to ACK compression.
Sample output :
$ nstat -n;sleep 1;nstat|egrep "IpInReceives|IpOutRequests|TcpInSegs|TcpOutSegs|TcpExtTCPAckCompressed"
IpInReceives 123250 0.0
IpOutRequests 3684 0.0
TcpInSegs 123251 0.0
TcpOutSegs 3684 0.0
TcpExtTCPAckCompressed 119252 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP receives an out-of-order packet, it immediately sends
a SACK packet, generating network load but also forcing the
receiver to send 1-MSS pathological packets, increasing its
RTX queue length/depth, and thus processing time.
Wifi networks suffer from this aggressive behavior, but generally
speaking, all these SACK packets add fuel to the fire when networks
are under congestion.
This patch adds a high resolution timer and tp->compressed_ack counter.
Instead of sending a SACK, we program this timer with a small delay,
based on RTT and capped to 1 ms :
delay = min ( 5 % of RTT, 1 ms)
If subsequent SACKs need to be sent while the timer has not yet
expired, we simply increment tp->compressed_ack.
When timer expires, a SACK is sent with the latest information.
Whenever an ACK is sent (if data is sent, or if in-order
data is received) timer is canceled.
Note that tcp_sack_new_ofo_skb() is able to force a SACK to be sent
if the sack blocks need to be shuffled, even if the timer has not
expired.
A new SNMP counter is added in the following patch.
Two other patches add sysctls to allow changing the 1,000,000 and 44
values that this commit hard-coded.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux-4.16 got support for softirq based hrtimers.
TCP can switch its pacing hrtimer to this variant, since this
avoids going through a tasklet and some atomic operations.
pacing timer logic looks like other (jiffies based) tcp timers.
v2: use hrtimer_try_to_cancel() in tcp_clear_xmit_timers()
to correctly release reference on socket if needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp_select_initial_window(), we only set rcv_wnd to
tcp_default_init_rwnd() if current mss > (1 << wscale). Otherwise,
rcv_wnd is kept at the full receive space of the socket which is a
value way larger than tcp_default_init_rwnd().
With larger initial rcv_wnd value, receive buffer autotuning logic
takes longer to kick in and increase the receive buffer.
In a TCP throughput test where receiver has rmem[2] set to 125MB
(wscale is 11), we see the connection gets recvbuf limited at the
beginning of the connection and gets less throughput overall.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RETPOLINE made calls to tp->af_specific->md5_lookup() quite expensive,
given they have no result.
We can omit the calls for sockets that have no md5 keys.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is second part of dealing with suboptimal device gso parameters.
In first patch (350c9f484b "tcp_bbr: better deal with suboptimal GSO")
we dealt with devices having low gso_max_segs
Some devices lower gso_max_size from 64KB to 16 KB (r8152 is an example)
In order to probe an optimal cwnd, we want BBR being not sensitive
to whatever GSO constraint a device can have.
This patch removes tso_segs_goal() CC callback in favor of
min_tso_segs() for CC wanting to override sysctl_tcp_min_tso_segs
Next patch will remove bbr->tso_segs_goal since it does not have
to be persistent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BBR uses tcp_tso_autosize() in an attempt to probe what would be the
burst sizes and to adjust cwnd in bbr_target_cwnd() with following
gold formula :
/* Allow enough full-sized skbs in flight to utilize end systems. */
cwnd += 3 * bbr->tso_segs_goal;
But GSO can be lacking or be constrained to very small
units (ip link set dev ... gso_max_segs 2)
What we really want is to have enough packets in flight so that both
GSO and GRO are efficient.
So in the case GSO is off or downgraded, we still want to have the same
number of packets in flight as if GSO/TSO was fully operational, so
that GRO can hopefully be working efficiently.
To fix this issue, we make tcp_tso_autosize() unaware of
sk->sk_gso_max_segs
Only tcp_tso_segs() has to enforce the gso_max_segs limit.
Tested:
ethtool -K eth0 tso off gso off
tc qd replace dev eth0 root pfifo_fast
Before patch:
for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
691 (ss -temoi shows cwnd is stuck around 6 )
667
651
631
517
After patch :
# for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
1733 (ss -temoi shows cwnd is around 386 )
1778
1746
1781
1718
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all skbs in write/rtx queues have CHECKSUM_PARTIAL,
we can remove dead code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer have skbs with skb->ip_summed == CHECKSUM_NONE
in TCP write queues.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid SKB coalescing if eor bit is set in one of the relevant
SKBs.
Fixes: c134ecb878 ("tcp: Make use of MSG_EOR in tcp_sendmsg")
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for calling sock_ops BPF program when there is a
retransmission. Three arguments are used; one for the sequence number,
another for the number of segments retransmitted, and the last one for
the return value of tcp_transmit_skb (0 => success).
Does not include syn-ack retransmissions.
New op: BPF_SOCK_OPS_RETRANS_CB.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Adds support for passing up to 4 arguments to sock_ops bpf functions. It
reusues the reply union, so the bpf_sock_ops structures are not
increased in size.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The two conditions triggering BUG_ON() are somewhat unrelated:
the tcp_skb_pcount() check is meant to catch TSO flaws, the
second one checks sanity of congestion window bookkeeping.
Split them into two separate BUG_ON() assertions on two lines,
so that we know which one actually triggers, when they do.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tail loss probe in cwnd reduction (CWR) state
to detect potential losses. Prior to this patch, since the sender
uses PRR to determine the cwnd in CWR state, the combination of
CWR+PRR plus tcp_tso_should_defer() could cause unnecessary stalls
upon losses: PRR makes cwnd so gentle that tcp_tso_should_defer()
defers sending wait for more ACKs. The ACKs may not come due to
packet losses.
Disallowing TLP when there is unused cwnd had the primary effect
of disallowing TLP when there is TSO deferral, Nagle deferral,
or we hit the rwin limit. Because basically every application
write() or incoming ACK will cause us to run tcp_write_xmit()
to see if we can send more, and then if we sent something we call
tcp_schedule_loss_probe() to see if we should schedule a TLP. At
that point, there are a few common reasons why some cwnd budget
could still be unused:
(a) rwin limit
(b) nagle check
(c) TSO deferral
(d) TSQ
For (d), after the next packet tx completion the TSQ mechanism
will allow us to send more packets, so we don't really need a
TLP (in practice it shouldn't matter whether we schedule one
or not). But for (a), (b), (c) the sender won't send any more
packets until it gets another ACK. But if the whole flight was
lost, or all the ACKs were lost, then we won't get any more ACKs,
and ideally we should schedule and send a TLP to get more feedback.
In particular for a long time we have wanted some kind of timer for
TSO deferral, and at least this would give us some kind of timer
Reported-by: Steve Ibanez <sibanez@stanford.edu>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Nandita Dukkipati <nanditad@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the TLP scheduling logic so that when scheduling a TLP probe, we
ensure that the estimated time at which an RTO would fire accounts for
the fact that ACKs indicating forward progress should push back RTO
times.
After the following fix:
df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
we had an unintentional behavior change in the following kind of
scenario: suppose the RTT variance has been very low recently. Then
suppose we send out a flight of N packets and our RTT is 100ms:
t=0: send a flight of N packets
t=100ms: receive an ACK for N-1 packets
The response before df92c8394e that was:
-> schedule a TLP for now + RTO_interval
The response after df92c8394e is:
-> schedule a TLP for t=0 + RTO_interval
Since RTO_interval = srtt + RTT_variance, this means that we have
scheduled a TLP timer at a point in the future that only accounts for
RTT_variance. If the RTT_variance term is small, this means that the
timer fires soon.
Before df92c8394e this would not happen, because in that code, when
we receive an ACK for a prefix of flight, we did:
1) Near the top of tcp_ack(), switch from TLP timer to RTO
at write_queue_head->paket_tx_time + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_LOSS_PROBE)
tcp_rearm_rto(sk);
2) In tcp_clean_rtx_queue(), update the RTO to now + RTO_interval:
if (flag & FLAG_ACKED) {
tcp_rearm_rto(sk);
3) In tcp_ack() after tcp_fastretrans_alert() switch from RTO
to TLP at now + RTO_interval:
if (icsk->icsk_pending == ICSK_TIME_RETRANS)
tcp_schedule_loss_probe(sk);
In df92c8394e we removed that 3-phase dance, and instead directly
set the TLP timer once: we set the TLP timer in cases like this to
write_queue_head->packet_tx_time + RTO_interval. So if the RTT
variance is small, then this means that this is setting the TLP timer
to fire quite soon. This means if the ACK for the tail of the flight
takes longer than an RTT to arrive (often due to delayed ACKs), then
the TLP timer fires too quickly.
Fixes: df92c8394e ("tcp: fix xmit timer to only be reset if data ACKed/SACKed")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
I had many reports that TSQ logic breaks wifi aggregation.
Current logic is to allow up to 1 ms of bytes to be queued into qdisc
and drivers queues.
But Wifi aggregation needs a bigger budget to allow bigger rates to
be discovered by various TCP Congestion Controls algorithms.
This patch adds an extra socket field, allowing wifi drivers to select
another log scale to derive TCP Small Queue credit from current pacing
rate.
Initial value is 10, meaning that this patch does not change current
behavior.
We expect wifi drivers to set this field to smaller values (tests have
been done with values from 6 to 9)
They would have to use following template :
if (skb->sk && skb->sk->sk_pacing_shift != MY_PACING_SHIFT)
skb->sk->sk_pacing_shift = MY_PACING_SHIFT;
Ref: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1670041
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Cc: Kir Kolyshkin <kir@openvz.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the reordering distance measurement in packet unit with
sequence based approach. Previously it trackes the number of "packets"
toward the forward ACK (i.e. highest sacked sequence)in a state
variable "fackets_out".
Precisely measuring reordering degree on packet distance has not much
benefit, as the degree constantly changes by factors like path, load,
and congestion window. It is also complicated and prone to arcane bugs.
This patch replaces with sequence-based approach that's much simpler.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FACK loss detection has been disabled by default and the
successor RACK subsumed FACK and can handle reordering better.
This patch removes FACK to simplify TCP loss recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that when a new netns is created, it inherits its
sysctl_tcp_rmem and sysctl_tcp_wmem from initial netns.
This change is needed so that we can refine TCP rcvbuf autotuning,
to take RTT into consideration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_init_nondata_skb() is fed with freshly allocated skbs.
They already have a cleared csum field, no need to clear it again.
This is based on Neal review on commit 3b11775033 ("tcp: do not mangle
skb->cb[] in tcp_make_synack()"), noticing I did not clear skb->csum.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
While stress testing MTU probing, we had crashes in list_del() that we root-caused
to the fact that tcp_fragment() is unconditionally inserting the freshly allocated
skb into tsorted_sent_queue list.
But this list is supposed to contain skbs that were sent.
This was mostly harmless until MTU probing was enabled.
Fortunately we can use the tcp_queue enum added later (but in same linux version)
for rtx-rb-tree to fix the bug.
Fixes: e2080072ed ("tcp: new list for sent but unacked skbs for RACK recovery")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Priyaranjan Jha <priyarjha@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch sent a patch to address the following issue :
tcp_make_synack() is leaving some TCP private info in skb->cb[],
then send the packet by other means than tcp_transmit_skb()
tcp_transmit_skb() makes sure to clear skb->cb[] to not confuse
IPv4/IPV6 stacks, but we have no such cleanup for SYNACK.
tcp_make_synack() should not use tcp_init_nondata_skb() :
tcp_init_nondata_skb() really should be limited to skbs put in write/rtx
queues (the ones that are only sent via tcp_transmit_skb())
This patch fixes the issue and should even save few cpu cycles ;)
Fixes: 971f10eca1 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tracepoint can be used to trace synack retransmits. It maintains
pointer to struct request_sock.
We cannot simply reuse trace_tcp_retransmit_skb() here, because the
sk here is the LISTEN socket. The IP addresses and ports should be
extracted from struct request_sock.
Note that, like many other tracepoints, this patch uses IS_ENABLED
in TP_fast_assign macro, which triggers sparse warning like:
./include/trace/events/tcp.h:274:1: error: directive in argument list
./include/trace/events/tcp.h:281:1: error: directive in argument list
However, there is no good solution to avoid these warnings. To the
best of our knowledge, these warnings are harmless.
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.
Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.
If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.
Bad things would then happen, including infinite loops.
This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.
Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.
Fixes: a47e5a988a ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event tcp_mtu_probe() is sending a packet, we
want tp->tcp_mstamp being as accurate as possible.
This means we need to call tcp_mstamp_refresh() a bit earlier in
tcp_write_xmit().
Fixes: 385e20706f ("tcp: use tp->tcp_mstamp in output path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMC protocol [1] relies on the use of a new TCP experimental
option [2, 3]. With this option, SMC capabilities are exchanged
between peers during the TCP three way handshake. This patch adds
support for this experimental option to TCP.
References:
[1] SMC-R Informational RFC: http://www.rfc-editor.org/info/rfc7609
[2] Shared Use of TCP Experimental Options RFC 6994:
https://tools.ietf.org/rfc/rfc6994.txt
[3] IANA ExID SMCR:
http://www.iana.org/assignments/tcp-parameters/tcp-parameters.xhtml#tcp-exids
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation calls tcp_rate_skb_sent() when tcp_transmit_skb()
is called when it clones skb only. Not calling tcp_rate_skb_sent() is OK
for all such code paths except from __tcp_retransmit_skb() which happens
when skb->data address is not aligned. This may rarely happen e.g. when
small amount of data is sent initially and the receiver partially acks
odd number of bytes for some reason, possibly malicious.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
New tracepoint trace_tcp_send_reset is added and called from
tcp_v4_send_reset(), tcp_v6_send_reset() and tcp_send_active_reset().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When retransmission on TSQ handler was introduced in the commit
f9616c35a0 ("tcp: implement TSQ for retransmits"), the retransmitted
skbs' timestamps were updated on the actual transmission. In the later
commit 385e20706f ("tcp: use tp->tcp_mstamp in output path"), it stops
being done so. In the commit, the comment says "We try to refresh
tp->tcp_mstamp only when necessary", and at present tcp_tsq_handler and
tcp_v4_mtu_reduced applies to this. About the latter, it's okay since
it's rare enough.
About the former, even though possible retransmissions on the tasklet
comes just after the destructor run in NET_RX softirq handling, the time
between them could be nonnegligibly large to the extent that
tcp_rack_advance or rto rearming be affected if other (remaining) RX,
BLOCK and (preceding) TASKLET sofirq handlings are unexpectedly heavy.
So in the same way as tcp_write_timer_handler does, doing tcp_mstamp_refresh
ensures the accuracy of algorithms relying on it.
Fixes: 385e20706f ("tcp: use tp->tcp_mstamp in output path")
Signed-off-by: Koichiro Den <den@klaipeden.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syn_data was allocated by sk_stream_alloc_skb(), meaning
its destructor and _skb_refdst fields are mangled.
We need to call tcp_skb_tsorted_anchor_cleanup() before
calling kfree_skb() or kernel crashes.
Bug was reported by syzkaller bot.
Fixes: e2080072ed ("tcp: new list for sent but unacked skbs for RACK recovery")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tried to hard avoiding a call to rb_first() (via tcp_rtx_queue_head)
in tcp_xmit_retransmit_queue(). But this was probably too bold.
Quoting Yuchung :
We might miss re-arming the RTO if tp->retransmit_skb_hint is not NULL.
This can happen when RACK marks the first packet lost again and resets
tp->retransmit_skb_hint for example (tcp_rack_mark_skb_lost())
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a real-time notification for tcp retransmission
for monitoring.
Of course we could use ftrace to dynamically instrument this
kernel function too, however we can't retrieve the connection
information at the same time, for example perf-tools [1] reads
/proc/net/tcp for socket details, which is slow when we have
a lots of connections.
Therefore, this patch adds a tracepoint for __tcp_retransmit_skb()
and exposes src/dst IP addresses and ports of the connection.
This also makes it easier to integrate into perf.
Note, I expose both IPv4 and IPv6 addresses at the same time:
for a IPv4 socket, v4 mapped address is used as IPv6 addresses,
for a IPv6 socket, LOOPBACK4_IPV6 is already filled by kernel.
Also, add sk and skb pointers as they are useful for BPF.
1. https://github.com/brendangregg/perf-tools/blob/master/net/tcpretrans
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Brendan Gregg <bgregg@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a linear list to store all skbs in write queue has been okay
for quite a while : O(N) is not too bad when N < 500.
Things get messy when N is the order of 100,000 : Modern TCP stacks
want 10Gbit+ of throughput even with 200 ms RTT flows.
40 ns per cache line miss means a full scan can use 4 ms,
blowing away CPU caches.
SACK processing often can use various hints to avoid parsing
whole retransmit queue. But with high packet losses and/or high
reordering, hints no longer work.
Sender has to process thousands of unfriendly SACK, accumulating
a huge socket backlog, burning a cpu and massively dropping packets.
Using an rb-tree for retransmit queue has been avoided for years
because it added complexity and overhead, but now is the time
to be more resistant and say no to quadratic behavior.
1) RTX queue is no longer part of the write queue : already sent skbs
are stored in one rb-tree.
2) Since reaching the head of write queue no longer needs
sk->sk_send_head, we added an union of sk_send_head and tcp_rtx_queue
Tested:
On receiver :
netem on ingress : delay 150ms 200us loss 1
GRO disabled to force stress and SACK storms.
for f in `seq 1 10`
do
./netperf -H lpaa6 -l30 -- -K bbr -o THROUGHPUT|tail -1
done | awk '{print $0} {sum += $0} END {printf "%7u\n",sum}'
Before patch :
323.87
351.48
339.59
338.62
306.72
204.07
304.93
291.88
202.47
176.88
2840
After patch:
1700.83
2207.98
2070.17
1544.26
2114.76
2124.89
1693.14
1080.91
2216.82
1299.94
18053
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new queue (list) that tracks the sent but not yet
acked or SACKed skbs for a TCP connection. The list is chronologically
ordered by skb->skb_mstamp (the head is the oldest sent skb).
This list will be used to optimize TCP Rack recovery, which checks
an skb's timestamp to judge if it has been lost and needs to be
retransmitted. Since TCP write queue is ordered by sequence instead
of sent time, RACK has to scan over the write queue to catch all
eligible packets to detect lost retransmission, and iterates through
SACKed skbs repeatedly.
Special cares for rare events:
1. TCP repair fakes skb transmission so the send queue needs adjusted
2. SACK reneging would require re-inserting SACKed skbs into the
send queue. For now I believe it's not worth the complexity to
make RACK work perfectly on SACK reneging, so we do nothing here.
3. Fast Open: currently for non-TFO, send-queue correctly queues
the pure SYN packet. For TFO which queues a pure SYN and
then a data packet, send-queue only queues the data packet but
not the pure SYN due to the structure of TFO code. This is okay
because the SYN receiver would never respond with a SACK on a
missing SYN (i.e. SYN is never fast-retransmitted by SACK/RACK).
In order to not grow sk_buff, we use an union for the new list and
_skb_refdst/destructor fields. This is a bit complicated because
we need to make sure _skb_refdst and destructor are properly zeroed
before skb is cloned/copied at transmit, and before being freed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our recent change exposed a bug in TCP Fastopen Client that syzkaller
found right away [1]
When we prepare skb with SYN+DATA, we attempt to transmit it,
and we update socket state as if the transmit was a success.
In socket RTX queue we have two skbs, one with the SYN alone,
and a second one containing the DATA.
When (malicious) ACK comes in, we now complain that second one had no
skb_mstamp.
The proper fix is to make sure that if the transmit failed, we do not
pretend we sent the DATA skb, and make it our send_head.
When 3WHS completes, we can now send the DATA right away, without having
to wait for a timeout.
[1]
WARNING: CPU: 0 PID: 100189 at net/ipv4/tcp_input.c:3117 tcp_clean_rtx_queue+0x2057/0x2ab0 net/ipv4/tcp_input.c:3117()
WARN_ON_ONCE(last_ackt == 0);
Modules linked in:
CPU: 0 PID: 100189 Comm: syz-executor1 Not tainted
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
0000000000000000 ffff8800b35cb1d8 ffffffff81cad00d 0000000000000000
ffffffff828a4347 ffff88009f86c080 ffffffff8316eb20 0000000000000d7f
ffff8800b35cb220 ffffffff812c33c2 ffff8800baad2440 00000009d46575c0
Call Trace:
[<ffffffff81cad00d>] __dump_stack
[<ffffffff81cad00d>] dump_stack+0xc1/0x124
[<ffffffff812c33c2>] warn_slowpath_common+0xe2/0x150
[<ffffffff812c361e>] warn_slowpath_null+0x2e/0x40
[<ffffffff828a4347>] tcp_clean_rtx_queue+0x2057/0x2ab0 n
[<ffffffff828ae6fd>] tcp_ack+0x151d/0x3930
[<ffffffff828baa09>] tcp_rcv_state_process+0x1c69/0x4fd0
[<ffffffff828efb7f>] tcp_v4_do_rcv+0x54f/0x7c0
[<ffffffff8258aacb>] sk_backlog_rcv
[<ffffffff8258aacb>] __release_sock+0x12b/0x3a0
[<ffffffff8258ad9e>] release_sock+0x5e/0x1c0
[<ffffffff8294a785>] inet_wait_for_connect
[<ffffffff8294a785>] __inet_stream_connect+0x545/0xc50
[<ffffffff82886f08>] tcp_sendmsg_fastopen
[<ffffffff82886f08>] tcp_sendmsg+0x2298/0x35a0
[<ffffffff82952515>] inet_sendmsg+0xe5/0x520
[<ffffffff8257152f>] sock_sendmsg_nosec
[<ffffffff8257152f>] sock_sendmsg+0xcf/0x110
Fixes: 8c72c65b42 ("tcp: update skb->skb_mstamp more carefully")
Fixes: 783237e8da ("net-tcp: Fast Open client - sending SYN-data")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove tcp_may_send_now and tcp_snd_test that are no longer used
Fixes: 840a3cbe89 ("tcp: remove forward retransmit feature")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now skb->mstamp_skb is updated later, we also need to call
tcp_rate_skb_sent() after the update is done.
Fixes: 8c72c65b42 ("tcp: update skb->skb_mstamp more carefully")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
liujian reported a problem in TCP_USER_TIMEOUT processing with a patch
in tcp_probe_timer() :
https://www.spinics.net/lists/netdev/msg454496.html
After investigations, the root cause of the problem is that we update
skb->skb_mstamp of skbs in write queue, even if the attempt to send a
clone or copy of it failed. One reason being a routing problem.
This patch prevents this, solving liujian issue.
It also removes a potential RTT miscalculation, since
__tcp_retransmit_skb() is not OR-ing TCP_SKB_CB(skb)->sacked with
TCPCB_EVER_RETRANS if a failure happens, but skb->skb_mstamp has
been changed.
A future ACK would then lead to a very small RTT sample and min_rtt
would then be lowered to this too small value.
Tested:
# cat user_timeout.pkt
--local_ip=192.168.102.64
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 `ifconfig tun0 192.168.102.64/16; ip ro add 192.0.2.1 dev tun0`
+0 < S 0:0(0) win 0 <mss 1460>
+0 > S. 0:0(0) ack 1 <mss 1460>
+.1 < . 1:1(0) ack 1 win 65530
+0 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_TCP, TCP_USER_TIMEOUT, [3000], 4) = 0
+0 write(4, ..., 24) = 24
+0 > P. 1:25(24) ack 1 win 29200
+.1 < . 1:1(0) ack 25 win 65530
//change the ipaddress
+1 `ifconfig tun0 192.168.0.10/16`
+1 write(4, ..., 24) = 24
+1 write(4, ..., 24) = 24
+1 write(4, ..., 24) = 24
+1 write(4, ..., 24) = 24
+0 `ifconfig tun0 192.168.102.64/16`
+0 < . 1:2(1) ack 25 win 65530
+0 `ifconfig tun0 192.168.0.10/16`
+3 write(4, ..., 24) = -1
# ./packetdrill user_timeout.pkt
Signed-off-by: Eric Dumazet <edumazet@googl.com>
Reported-by: liujian <liujian56@huawei.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 45f119bf93.
Eric Dumazet says:
We found at Google a significant regression caused by
45f119bf93 tcp: remove header prediction
In typical RPC (TCP_RR), when a TCP socket receives data, we now call
tcp_ack() while we used to not call it.
This touches enough cache lines to cause a slowdown.
so problem does not seem to be HP removal itself but the tcp_ack()
call. Therefore, it might be possible to remove HP after all, provided
one finds a way to elide tcp_ack for most cases.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
With new TCP_FASTOPEN_CONNECT socket option, there is a possibility
to call tcp_connect() while socket sk_dst_cache is either NULL
or invalid.
+0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4
+0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0
+0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0
+0 connect(4, ..., ...) = 0
<< sk->sk_dst_cache becomes obsolete, or even set to NULL >>
+1 sendto(4, ..., 1000, MSG_FASTOPEN, ..., ...) = 1000
We need to refresh the route otherwise bad things can happen,
especially when syzkaller is running on the host :/
Fixes: 19f6d3f3c8 ("net/tcp-fastopen: Add new API support")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a TCP loss recovery performance bug raised recently on the netdev
list, in two threads:
(i) July 26, 2017: netdev thread "TCP fast retransmit issues"
(ii) July 26, 2017: netdev thread:
"[PATCH V2 net-next] TLP: Don't reschedule PTO when there's one
outstanding TLP retransmission"
The basic problem is that incoming TCP packets that did not indicate
forward progress could cause the xmit timer (TLP or RTO) to be rearmed
and pushed back in time. In certain corner cases this could result in
the following problems noted in these threads:
- Repeated ACKs coming in with bogus SACKs corrupted by middleboxes
could cause TCP to repeatedly schedule TLPs forever. We kept
sending TLPs after every ~200ms, which elicited bogus SACKs, which
caused more TLPs, ad infinitum; we never fired an RTO to fill in
the holes.
- Incoming data segments could, in some cases, cause us to reschedule
our RTO or TLP timer further out in time, for no good reason. This
could cause repeated inbound data to result in stalls in outbound
data, in the presence of packet loss.
This commit fixes these bugs by changing the TLP and RTO ACK
processing to:
(a) Only reschedule the xmit timer once per ACK.
(b) Only reschedule the xmit timer if tcp_clean_rtx_queue() deems the
ACK indicates sufficient forward progress (a packet was
cumulatively ACKed, or we got a SACK for a packet that was sent
before the most recent retransmit of the write queue head).
This brings us back into closer compliance with the RFCs, since, as
the comment for tcp_rearm_rto() notes, we should only restart the RTO
timer after forward progress on the connection. Previously we were
restarting the xmit timer even in these cases where there was no
forward progress.
As a side benefit, this commit simplifies and speeds up the TCP timer
arming logic. We had been calling inet_csk_reset_xmit_timer() three
times on normal ACKs that cumulatively acknowledged some data:
1) Once near the top of tcp_ack() to switch from TLP timer to RTO:
if (icsk->icsk_pending == ICSK_TIME_LOSS_PROBE)
tcp_rearm_rto(sk);
2) Once in tcp_clean_rtx_queue(), to update the RTO:
if (flag & FLAG_ACKED) {
tcp_rearm_rto(sk);
3) Once in tcp_ack() after tcp_fastretrans_alert() to switch from RTO
to TLP:
if (icsk->icsk_pending == ICSK_TIME_RETRANS)
tcp_schedule_loss_probe(sk);
This commit, by only rescheduling the xmit timer once per ACK,
simplifies the code and reduces CPU overhead.
This commit was tested in an A/B test with Google web server
traffic. SNMP stats and request latency metrics were within noise
levels, substantiating that for normal web traffic patterns this is a
rare issue. This commit was also tested with packetdrill tests to
verify that it fixes the timer behavior in the corner cases discussed
in the netdev threads mentioned above.
This patch is a bug fix patch intended to be queued for -stable
relases.
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Reported-by: Klavs Klavsen <kl@vsen.dk>
Reported-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang