Add clocks for SPIBSC blocks.
Also modify the flash node for the GR-PEACH board at the same time
because now that the SPIBSC clock is identified, if it is not used
by any driver, it will be turned off at the end of kernel boot.
That would not work out so well for an XIP system such as GR-PEACH.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Link: https://lore.kernel.org/r/20200210123153.8257-1-chris.brandt@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To improve human readability and enable automatic validation, the tuples
in the various properties containing interrupt specifiers should be
grouped. While "make dtbs_check" does not impose this yet for the
"interrupts" property, it does for the "interrupt-map" property, leading
to warnings like:
pci@ee090000: interrupt-map:0: [0, 0, 0, 1, 5, 0, 108, 4, 2048, 0, 0, 1, 5, 0, 108, 4, 4096, 0, 0, 2, 5, 0, 108, 4] is too long
pci@ee0d0000: interrupt-map:0: [0, 0, 0, 1, 5, 0, 113, 4, 2048, 0, 0, 1, 5, 0, 113, 4, 4096, 0, 0, 2, 5, 0, 113, 4] is too long
Fix this by grouping the tuples of the "interrupts" and "interrupt-map"
properties using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-4-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Enable support for the IRQC on RZ/A1H, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A9
CPU core on RZ/A1H by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to table 7.3 ("List of Interrupt IDs") in the RZ/A1H Hardware
User's Manual rev. 3.00, the realtime clock interrupts are level not
edge interrupts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to table 7.3 ("List of Interrupt IDs") in the RZ/A1H Hardware
User's Manual rev. 3.00, the watchdog timer interrupt is a level
interrupt.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sort the subnodes of the soc node to improve maintainability.
The sort has been done alphabetically with the node name as the key.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The current practice is to not group clocks under a "clocks" subnode,
but just put them together with the other on-SoC devices.
As per updates for R-Car Gen2 SoCs by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort the subnodes of the soc node to improve maintainability.
The sort key is the address on the bus with instances of the same
IP block grouped together and sorted alphabetically.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add soc node to represent the bus and move all nodes with a base address
into this node. This is consistent with handling of R-Car Gen3 and Gen2
SoCs in mainline. It is intended to migrate other Renesas ARM-based
SoCs to this scheme.
The ordering is derived from simply moving each node with an address up to
before any nodes without a base address that occur before the soc node. To
improve maintainability follow-up patches will sort subnodes of both the
new soc node and the root node.
This patch should not introduce any functional change.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Improve hardware description by adding a clock property to the device
node corresponding to the CA9 CPU core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the USB0 and USB1 clocks to the device tree.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved over
from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288 SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using arm/
and arm64/ as include prefixes. This will avoid other local hacks such as
per-file links between the two arch trees (this broke for external mirroring
of DT contents). Now they can just provide their own appropriate dt-include
hierarcy per platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6w6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
Add the RTC clocks to device tree. The frequencies must be fixed values
according to the hardware manual.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Technically, the Ethernet block is run off the 133MHz Bus (B) clock, not
the 33MHz Peripheral 0 (P0) clock.
Fixes: 969244f9c7 ("ARM: dts: r7s72100: add ethernet clock to device tree")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Note that early-bresp-disable and full-line-zero-disable are required
because the sideband signals between the CPU and L2C were not connected
in this SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add watchdog timer support for RZ/A1.
For the RZ/A1, the only way to do a reset is to overflow the WDT, so this
is useful even if you don't need the watchdog functionality.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SDHI controller in the RZ/A1 has 2 clock sources per channel and both
need to be enabled/disabled for proper operation. This fixes the fact that
the define for R7S72100_CLK_SDHI1 was not correct to begin with (typo), and
that all 4 clock sources need to be defined an used.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Fixed rate and fixed factor clocks do not require an
clock-output-names property.
* Since 07705583e9 ("clk: shmobile: div6: Make clock-output-names
optional") Renesas div6 clocks do not require a clock-output-names
property.
In the above cases there is only one clock output and its name is taken
from that of the clock node. Accordingly, remove the unnecessary
clock-output-names properties and as necessary update the node names.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock is really the device functional clock, not the interface
clock. Rename it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use GIC_* defines for GIC interrupt cells in r7s72100 device tree.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed (thanks Chris, Wolfram!) by reading the
GICD_IIDR register, which reports 0x0000043b (PL390 = 0x00, ARM =
0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add an appropriate "#power-domain-cells" property to the cpg_clocks
device node, to create the CPG/MSTP Clock Domain.
Add "power-domains" properties to all device nodes for devices that are
part of the CPG/MSTP Clock Domain and can be power-managed through an
MSTP clock. This applies to most on-SoC devices, which have a
one-to-one mapping from SoC device to DT device node.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In general Renesas hardware is not documented to the extent
where the relationship between IP blocks on different SoCs can be assumed
although they may appear to operate the same way. Furthermore the
documentation typically does not specify a version for individual
IP blocks. For these reasons a convention of using the SoC name in place
of a version and providing SoC-specific compat strings has been adopted.
Although not universally liked this convention is used in the bindings for
a number of drivers for Renesas hardware. The purpose of this patch is to
make use of the SoC-specific CMT compat string for the r7s72100 MTU2
clock source.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the MTU2 counter to the r7s72100 device tree and make it disabled by
default.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[horms+renesas@verge.net.au correct irq number]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CPU Frequency information to the r7s72100 DTS file. This
will allow us to use the shared C code on r7s72100 and Genmai
which reads out the clock frequency from DT and calculates the
delay settings from there.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only essential clocks are added for now. Other clocks will be added when
needed.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Chris Brandt