Commit Graph

6793 Commits

Author SHA1 Message Date
Eugenia Emantayev 93591aaa62 net/mlx4_en: Pad ethernet packets smaller than 17 bytes
Hardware can't accept packets smaller than 17 bytes. Therefore need to
pad with zeros.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 20:04:00 -05:00
Eugenia Emantayev b97b33a3df net/mlx4_en: Verify mlx4_en module parameters
Verify mlx4_en module parameters.
In case they are out of range - reset to default values.

Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 20:04:00 -05:00
Amir Vadai fd8daa45f2 net/mlx4_en: Fix UP limit in ieee_ets->prio_tc
User priority limit has to be less than MLX4_EN_NUM_UP.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 20:04:00 -05:00
Jacob Keller 93501d48b8 ixgbe: implement SIOCGHWTSTAMP ioctl
This patch adds support for the new SIOCGHWTSTAMP ioctl, which enables a
process to determine the current timestamp configuration. In order to
implement this, store a copy of the timestamp configuration. In
addition, we can remove the 'int cmd' parameter as the new set_ts_config
function doesn't use it. I also fixed a typo in the function
description.

-v2
* Only save the settings after validating them

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 19:06:44 -05:00
Mark Rustad 144384649d ixgbe: Check config reads for removal
Configuration space reads should also be checked for removal. So
add some checks related to config space accesses.

v2:
* Fixed indent

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 19:06:43 -05:00
Mark Rustad 0edd2bdf63 ixgbe: Fix up some ethtool results when adapter is removed
Some ethtool tests returned apparently good results when the
adapter was in a removed state. Fix that by checking for removal.
This also fixes two paths that could return uninitialized memory
in data[4].

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 19:06:43 -05:00
Mark Rustad 0391bbe3e4 ixgbe: Restore hw_addr in LER recovery paths
The hw_addr needs to be restored in the pcie recovery path or
else the device will be perpetually removed. Also restore the
value in the resume path.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-02 19:06:43 -05:00
Jingoo Han 4e76ca7f3e net: w5100: Use devm_ioremap_resource()
Use devm_ioremap_resource() in order to make the code simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 16:57:24 -05:00
Jingoo Han d1b44ce1a3 net: w5300: Use devm_ioremap_resource()
Use devm_ioremap_resource() in order to make the code simpler.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 16:57:24 -05:00
Emil Tantilov 01a545cf21 ixgbevf: add check for CHECKSUM_PARTIAL when doing TSO
This patch adds check for CHECKSUM_PARTIAL to avoid the skb_is_gso check
in ixgbevf_tso(). It should reduce overhead for workloads that are not using
TSO or checksum offloads. It is the same as in ixgbe.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 12:40:57 -05:00
Emil Tantilov b5d217f3a7 ixgbevf: fix handling of tx checksumming
This patch resolves an issue introduced by:
commit 7ad1a09351
ixgbevf: make the first tx_buffer a repository for most of the skb info

Incorrect check for the result of ixgbevf_tso() can lead to calling
ixgbevf_tx_csum() which can spawn 2 context descriptors and result in
performance degradation and/or corrupted packets.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 12:40:57 -05:00
Don Skidmore c97506ab0e ixgbe: Add check for FW veto bit
The driver will now honor the MNG FW veto bit in blocking link resets.
This patch will affect x520 and x540 systems.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 12:40:57 -05:00
Don Skidmore 9f4d278ffb ixgbe: fix bit toggled for 82599 reset fix.
The current code doesn't toggle the correct bit to reset the data pipeline
on Restart_AN assertion.  This patch corrects that.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 12:40:56 -05:00
Don Skidmore 429d6a3be9 ixgbe: collect all 82599 AUTOC code in one function
When reading or writing to the AUTOC register on 82599 devices we need to
preform various operations that aren't needed for other MAC types.  This
patch will collect all of that code into one place to minimize MAC checks
in common code paths.

While doing this I also clean up some cases where we weren't holding the
SW/FW semaphore during a read/modify/write of AUTOC.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 12:40:56 -05:00
Don Skidmore 1f86c983be ixgbe: fix to use correct timeout interval for memory read completion
Currently we were just always polling for a hard coded 80 ms and not
respecting the system-wide timeout interval.  Since up until now all
devices have been tested with this 80ms value we continue to use this
value as a hard minimum.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-28 12:40:56 -05:00
Carolyn Wyborny 74cfb2e1f2 igb: Update license text to remove FSF address and update copyright.
This patch updates the license text to remove address of Free Software
Foundation and refer  users to www.gnu.org instead. This patch also updates
the copyright dates in appropriate igb driver files.

Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:54:52 -05:00
Jeff Kirsher 167f3f71c7 igb: make local functions static and remove dead code
Based on Stephen Hemminger's original patch.
Make local functions static, and remove unused functions.

Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:54:52 -05:00
Mark Rustad 87557440d8 ixgbe: Add WoL support for a new device
Add WoL support for port 0 of a new 82599-based device.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:54:52 -05:00
Jacob Keller ca324099fb ixgbe: don't use magic size number to assign ptp_caps.name
Rather than using a magic size number, just use sizeof since that will
work and is more robust to future changes.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:54:51 -05:00
Don Skidmore d773ce2de1 ixgbe: modify behavior on receiving a HW ECC error.
Currently when we noticed a HW ECC error we would request the use reload
the driver to force a reset of the part.  This was done due to the mistaken
believe that a normal reset would not be sufficient.  Well it turns out it
would be so now we just schedule a reset upon seeing the ECC.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:54:51 -05:00
Amir Vadai ca9f9f7039 net/mlx4_en: Fix bad use of dev_id
dev_id should be set for multiple netdev's sharing the same MAC, which
is not the case here.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:38:07 -05:00
Amir Vadai 76a066f2a2 net/mlx4_en: Expose port number through sysfs
Initialize dev_port with port number (0 based) to be accessed through
sysfs from user space.

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:38:06 -05:00
Michal Schmidt 94d9de3cf7 bnx2x: save RAM in kdump kernel by disabling TPA
When running in a kdump kernel, disable TPA. This saves memory, which
tends to be scarce in kdump.

TPA, being a receive acceleration, is unlikely to be useful for kdump,
whose purpose is to send the memory image out.

This saves additional 5 MB in the kdump environment.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:27:50 -05:00
Michal Schmidt ff2ad3071f bnx2x: save RAM in kdump kernel by using a single queue
When running in a kdump kernel, make sure to use only a single ethernet
queue even if a num_queues option in /etc/modprobe.d/*.conf would specify
otherwise. This saves memory, which tends to be scarce in kdump.

This saves about 40 MB in the kdump environment on a setup with
num_queues=8 in the config file.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:27:50 -05:00
Michal Schmidt 7d0445d66a bnx2x: clamp num_queues to prevent passing a negative value
Use the clamp() macro to make the calculation of the number of queues
slightly easier to understand. It also avoids a crash when someone
accidentally passes a negative value in num_queues= module parameter.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-26 15:27:50 -05:00
Joe Perches cd2b0389dc bnx2x: Remove hidden flow control goto from BNX2X_ALLOC macros
BNX2X_ALLOC macros use "goto alloc_mem_err"
so these labels appear unused in some functions.

Expand these macros in-place via coccinelle and
some typing.

Update the macros to use statement expressions
and remove the BNX2X_ALLOC macro.

This adds some > 80 char lines.

$ cat bnx2x_pci_alloc.cocci
@@
expression e1;
expression e2;
expression e3;
@@
-	BNX2X_PCI_ALLOC(e1, e2, e3);
+	e1 = BNX2X_PCI_ALLOC(e2, e3); if (!e1) goto alloc_mem_err;

@@
expression e1;
expression e2;
expression e3;
@@
-	BNX2X_PCI_FALLOC(e1, e2, e3);
+	e1 = BNX2X_PCI_FALLOC(e2, e3); if (!e1) goto alloc_mem_err;

@@
expression e1;
expression e2;
@@
-	BNX2X_ALLOC(e1, e2);
+	e1 = kzalloc(e2, GFP_KERNEL); if (!e1) goto alloc_mem_err;

@@
expression e1;
expression e2;
expression e3;
@@
-	kzalloc(sizeof(e1) * e2, e3)
+	kcalloc(e2, sizeof(e1), e3)

@@
expression e1;
expression e2;
expression e3;
@@
-	kzalloc(e1 * sizeof(e2), e3)
+	kcalloc(e1, sizeof(e2), e3)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-25 17:36:35 -05:00
Florian Fainelli 51adfcc333 net: bcmgenet: remove unused bh_lock member
bh_lock spinlock is unused, remove it from the private driver structure.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 20:26:37 -05:00
Florian Fainelli da56bbf71d net: bcmgenet: remove commented code in bcmgenet_xmit()
This code is commented since it is unused, left-over from the very first
time this driver was merged.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 20:26:36 -05:00
Florian Fainelli 80d8e96d12 net: bcmgenet: drop checks on priv->phydev
Drop all the checks on priv->phydev since we will refuse probing the
driver if we cannot attach to a PHY device. Drop all checks on
priv->phydev. This also fixes some smatch issues reported by Dan
Carpenter.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 20:26:36 -05:00
Claudiu Manoil f19015baa2 gianfar: Fix Tx int miss, dont write IC on-the-fly
Programming the interrupt coalescing (IC) registers while
the controller/DMA is on may incur the loss of one Tx
confirmation interrupt, under certain conditions.  This is
a subtle hw race because it does not occur during a burst
of Tx packets.  It has been observed on p2020 devices that,
if just one packet is being xmit'ed, the Tx confirmation
doesn't trigger and BQL evetually blocks the Tx queues,
followed by Tx timeout and an un-responsive device.
This issue was not apparent prior to introducing BQL
support, as a late Tx confirmation was not an issue back then
and the next burst of Tx frames would have triggered the
Tx confirmation/ Tx ring cleanup anyway.

Bottom line, the hw specifications state that the IC registers
should not be programmed while the Rx/Tx blocks (the DMA) are
enabled. Further more, these registers are currently re-written
with the same values on the processing path, over and over again.
To fix this, rewriting the IC registers has been removed from
the processing path (napi poll).  A complete MAC reset procedure
has been implemented for the ethtool -c option instead, to
reliably update these registers while the controller is stopped.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:38:20 -05:00
Claudiu Manoil 0851133bb5 gianfar: Fix device reset races (oops) for Tx
The device reset procedure, stop_gfar()/startup_gfar(), has
concurrency issues.
"Kernel access of bad area" oopses show up during Tx timeout
device reset or other reset cases (like changing MTU) that
happen while the interface still has traffic. The oopses
happen in start_xmit and clean_tx_ring when accessing tx_queue->
tx_skbuff which is NULL. The race comes from de-allocating the
tx_skbuff while transmission and napi processing are still
active. Though the Tx queues get temoprarily stopped when Tx
timeout occurs, they get re-enabled as a result of Tx congestion
handling inside the napi context (see clean_tx_ring()). Not
disabling the napi during reset is also a bug, because
clean_tx_ring() will try to access tx_skbuff while it is being
de-alloc'ed and re-alloc'ed.

To fix this, stop_gfar() needs to disable napi processing
after stopping the Tx queues. However, in order to prevent
clean_tx_ring() to re-enable the Tx queue before the napi
gets disabled, the device state DOWN has been introduced.
It prevents the Tx congestion management from re-enabling the
de-congested Tx queue while the device is brought down.
An additional locking state, RESETTING, has been introduced
to prevent simultaneous resets or to prevent configuring the
device while it is resetting.
The bogus 'rxlock's (for each Rx queue) have been removed since
their purpose is not justified, as they don't prevent nor are
suited to prevent device reset/reconfig races (such as this one).

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:38:20 -05:00
Claudiu Manoil 80ec396cb6 gianfar: Don't free/request irqs on device reset
Resetting the device (stop_gfar()/startup_gfar()) should
be fast and to the point, in order to timely recover
from an error condition (like Tx timeout) or during
device reconfig.  The irq free/ request routines are just
redundant here, and they should be part of the device
close/ open routines instead.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:38:20 -05:00
Claudiu Manoil 88302648be gianfar: Fix on-the-fly vlan and mtu updates
The RCTRL and TCTRL registers should not be changed
on-the-fly, while the controller is running, otherwise
unexpected behaviour occurs.  But that's exactly what
gfar_vlan_mode() does, updating the VLAN acceleration
bits inside RCTRL/TCTRL.  The attempt to lock these
operations doesn't help, but only adds to the confusion.
There's also a dependency for Rx FCB insertion (activating
/de-activating the TOE offload block on Rx) which might
change the required rx buffer size.  This makes matters
worse as gfar_vlan_mode() ends up calling gfar_change_mtu(),
though the MTU size remains the same.  Note that there are
other situations that may affect the required rx buffer size,
like changing RXCSUM or rx hw timestamping, but errorneously
the rx buffer size is not recomputed/ updated in the process.

To fix this, do the vlan updates properly inside the MAC
reset and reconfiguration procedure, which takes care of
the rx buffer size dependecy and the rx TOE block (PRSDEP)
activation/deactivation as well (in the correct order).
As a consequence, MTU/ rx buff size updates are done now
by the same MAC reset and reconfig procedure, so that out
of context updates to MAXFRM, MRBLR, and MACCFG inside
change_mtu() are no longer needed.  The rx buffer size
dependecy to Rx FCB is now handled for the other cases too
(RXCSUM and rx hw timestamping).

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:38:20 -05:00
Claudiu Manoil a328ac92d3 gianfar: Implement MAC reset and reconfig procedure
The main MAC config registers like: RCTRL/TCTRL, MRBLR,
MAXFRM, RXIC/TXIC, most fields of MACCFG1/2, should not
be changed on-the-fly, but at least after stopping the
DMA and disabling the Rx/Tx blocks and, for increased
reliability, after a MAC soft reset.

Impelement a complete MAC soft reset and reconfig procedure
following the latest HW advisories - gfar_mac_reset() - to
replace gfar_mac_init() and (the confusing) init_registers()
functions.

Factor out separate config functions for RCTRL and TCTRL,
insure programming order of the relevant config regs after
MAC soft reset.

Split gfar_hw_init() into gfar_mac_reset() and the remaining
global regs that don't need to be reconfigured after MAC soft
reset (FIFOCFG, ATTRELI, HW counters a.s.o).

As gfar_hw_init() now makes all the register writes @probe()
time, based on all the device flags and config options, it
must be moved further down, just before register_netdev(),
as the last config step when the config values are comitted
to HW.  Also, move netif_carrier_off() after register_netdev(),
because it has no effect if called before.

Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:38:20 -05:00
David S. Miller 225a9a2566 bcmgenet: Deleted unnecessary select_queue method.
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:33:27 -05:00
Fabio Estevam 5343a10d15 net: bcmgenet: Use devm_ioremap_resource()
According to Documentation/driver-model/devres.txt, devm_request_and_ioremap()
is deprecated, so use devm_ioremap_resource() instead.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:28:56 -05:00
Ben Hutchings e8b39015b5 cgxb4: Stop using ethtool SPEED_* constants
ethtool speed values are just numbers of megabits and there is no need
to add SPEED_40000.  To be consistent, use integer constants directly
for all speeds.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 19:04:08 -05:00
Shahed Shaikh 3dd4705698 qlcnic: Update version to 5.3.56
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:43:19 -05:00
Harish Patil 1a51042bb8 qlcnic: Enhance semaphore lock access failure error message
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:43:19 -05:00
Rajesh Borundia cecd59d84d qlcnic: Allow vlan0 traffic
o Adapter allows vlan0 traffic in case of SR-IOV after setting
  QLC_SRIOV_ALLOW_VLAN0 bit even though we do not add vlan0 filters.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:43:19 -05:00
Sucheta Chakraborty 2a355aecd2 qlcnic: Enhance driver message in failed state.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:43:19 -05:00
Jitendra Kalsaria d91abf903b qlcnic: Updates to QLogic application/driver interface for virtual NIC configuration
Qlogic application interface in the driver which has larger than 8 vNIC
configuration support has been updated to handle the following cases:

o Only 8 or lower total vNICs were enabled within the vNIC 0-7 range
o vNICs were enabled in the vNIC 0-15 range such that enabled vNICs were
  not contiguous and only 8 or lower number of total VNICs were enabled
o Disconnect in the vNIC mapping between application and driver when the
  enabled VNICs were dis contiguous

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:43:19 -05:00
Shahed Shaikh 225837a076 qlcnic: Re-factor firmware minidump template header handling
Treat firmware minidump template headers for 82xx and 83xx/84xx adapters separately,
as it may change for 82xx and 83xx/84xx adapter type independently.

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:43:19 -05:00
Ido Shamay bb2146bc88 net/mlx4: Fix limiting number of IRQ's instead of RSS queues
This fix a performance bug introduced by commit 90b1ebe "mlx4: set
maximal number of default RSS queues", which limits the numbers of IRQs
opened by core module.
The limit should be on the number of queues in the indirection table -
rx_rings, and not on the number of IRQ's. Also, limiting on mlx4_core
initialization instead of in mlx4_en, prevented using "ethtool -L" to
utilize all the CPU's, when performance mode is prefered, since limiting
this number to 8 reduces overall packet rate by 15%-50% in multiple TCP
streams applications.

For example, after running ethtool -L <ethx> rx 16

          Packet rate
Before the fix  897799
After the fix   1142070

Results were obtained using netperf:

S=200 ; ( for i in $(seq 1 $S) ; do ( \
  netperf -H 11.7.13.55 -t TCP_RR -l 30 &) ; \
  wait ; done | grep "1        1" | awk '{SUM+=$6} END {print SUM}' )

CC: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:38:14 -05:00
Ido Shamay 0251248232 net/mlx4: Set number of RX rings in a utility function
mlx4_en_add() is too long.
Moving set number of RX rings to a utiltity function to improve
readability and modulization of the code.

Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-24 18:38:01 -05:00
Catherine Sullivan acbc3eb5f8 i40e and i40evf: Bump driver versions
Update the driver versions.

Change-ID: I3fe23024d17da0e614ce126edb365bb2c428d482
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-21 12:38:26 -05:00
Catherine Sullivan 77fa28befc i40e: Change MSIX to MSI-X
Fix inconsistent use of MSIX and MSI-X in messages.

Change-ID: Iae9ffb42819677c34544719044ed77632e06147d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-21 12:38:26 -05:00
Mitch Williams 6c5ef6209d i40e: tighten up ring enable/disable flow
Change the do/while to a for loop, so we don't hit the delay each
time, even when the register is ready for action.
Don't bother to set or clear the QENA_STAT bit as it is
read-only.

Change-ID: Ie464718804dd79f6d726f291caa9b0c872b49978
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-21 12:38:26 -05:00
Mitch Williams 81b8c0117d i40e: remove unnecessary delay
Ain't nothing gonna break my stride, nobody's gonna slow me down,
oh no. I got to keep on moving.

This was originally put in for debugging just-in-case purposes
and never removed.

Change-ID: Ic12c2e179c3923f54e6ba0a9e4ab05d25c3bab29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-21 12:38:26 -05:00
Mitch A Williams 821bd3e65d i40evf: remove errant space
Remove a bogus space.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-21 12:38:26 -05:00