Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.
Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.
Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.
The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.
If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three string sets related to timestamping information:
ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
ETH_SS_TS_TX_TYPES: timestamping Tx types
ETH_SS_TS_RX_FILTERS: timestamping Rx filters
These will be used for TIMESTAMP_GET request.
v2: avoid compiler warning ("enumeration value not handled in switch")
in net_hwtstamp_validate()
v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for low latency Reed Solomon FEC as LLRS.
The LL-FEC is defined by the 25G/50G ethernet consortium,
in the document titled "Low Latency Reed Solomon Forward Error Correction"
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Implement WOL_GET request to get wake-on-lan settings for a device,
traditionally available via ETHTOOL_GWOL ioctl request.
As part of the implementation, provide symbolic names for wake-on-line
modes as ETH_SS_WOL_MODES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement DEBUG_GET request to get debugging settings for a device. At the
moment, only message mask corresponding to message level as reported by
ETHTOOL_GMSGLVL ioctl request is provided. (It is called message level in
ioctl interface but almost all drivers interpret it as a bit mask.)
As part of the implementation, provide symbolic names for message mask bits
as ETH_SS_MSG_CLASSES string set.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Requests a contents of one or more string sets, i.e. indexed arrays of
strings; this information is provided by ETHTOOL_GSSET_INFO and
ETHTOOL_GSTRINGS commands of ioctl interface. Unlike ioctl interface, all
information can be retrieved with one request and mulitple string sets can
be requested at once.
There are three types of requests:
- no NLM_F_DUMP, no device: get "global" stringsets
- no NLM_F_DUMP, with device: get string sets related to the device
- NLM_F_DUMP, no device: get device related string sets for all devices
Client can request either all string sets of given type (global or device
related) or only specific sets. With ETHTOOL_A_STRSET_COUNTS flag set, only
set sizes (numbers of strings) are returned.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike e.g. netdev features, the ethtool ioctl interface requires link mode
table to be in sync between kernel and userspace for userspace to be able
to display and set all link modes supported by kernel. The way arbitrary
length bitsets are implemented in netlink interface, this will be no longer
needed.
To allow userspace to access all link modes running kernel supports, add
table of ethernet link mode names and make it available as a string set to
userspace GET_STRSET requests. Add build time check to make sure names
are defined for all modes declared in enum ethtool_link_mode_bit_indices.
Once the string set is available, make it also accessible via ioctl.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 400Gbps speed, link modes of 50Gbps per lane
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The `phy_tunable_id` has been named `ETHTOOL_PHY_EDPD` since it looks like
this feature is common across other PHYs (like EEE), and defining
`ETHTOOL_PHY_ENERGY_DETECT_POWER_DOWN` seems too long.
The way EDPD works, is that the RX block is put to a lower power mode,
except for link-pulse detection circuits. The TX block is also put to low
power mode, but the PHY wakes-up periodically to send link pulses, to avoid
lock-ups in case the other side is also in EDPD mode.
Currently, there are 2 PHY drivers that look like they could use this new
PHY tunable feature: the `adin` && `micrel` PHYs.
The ADIN's datasheet mentions that TX pulses are at intervals of 1 second
default each, and they can be disabled. For the Micrel KSZ9031 PHY, the
datasheet does not mention whether they can be disabled, but mentions that
they can modified.
The way this change is structured, is similar to the PHY tunable downshift
control:
* a `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` value is exposed to cover a default
TX interval; some PHYs could specify a certain value that makes sense
* `ETHTOOL_PHY_EDPD_NO_TX` would disable TX when EDPD is enabled
* `ETHTOOL_PHY_EDPD_DISABLE` will disable EDPD
As noted by the `ETHTOOL_PHY_EDPD_DFLT_TX_MSECS` the interval unit is 1
millisecond, which should cover a reasonable range of intervals:
- from 1 millisecond, which does not sound like much of a power-saver
- to ~65 seconds which is quite a lot to wait for a link to come up when
plugging a cable
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add link modes for 100Mbps and 1Gbps over a single pair.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added max EEPROM length defines for ethtool usage:
#define ETH_MODULE_SFF_8636_MAX_LEN 640
#define ETH_MODULE_SFF_8436_MAX_LEN 640
These definitions are used to determine the EEPROM
data length when reading high eeprom pages.
For example, SFF-8636 EEPROM data from page 03h
needs to be stored at data[512] - data[639].
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When building C++ userspace code that includes ethtool.h
with "-Werror -Wall", g++ complains about signed-unsigned comparison in
ethtool_validate_speed() due to definition of SPEED_UNKNOWN as -1.
Explicitly cast SPEED_UNKNOWN to __u32 to match type of
ethtool_validate_speed() argument.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for Fast Link Down as new PHY tunable.
Fast Link Down reduces the time until a link down event is reported
for 1000BaseT. According to the standard it's 750ms what is too long
for several use cases.
v2:
- add comment describing the constants
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way to define __ETHTOOL_LINK_MODE_MASK_NBITS seems to be overly
complicated, go with a standard approach instead.
Whilst we're at it, move the comment to the right place.
v2:
- rebased
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for 50Gbps per lane link modes. Define various 50G, 100G
and 200G link modes using it.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Trivial spelling errors found by codespell.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since [gs]et_settings ethtool_ops callbacks have been deprecated in
February 2016, all in tree NIC drivers have been converted to provide
[gs]et_link_ksettings() and out of tree drivers have had enough time to do
the same.
Drop get_settings() and set_settings() and implement both ETHTOOL_[GS]SET
and ETHTOOL_[GS]LINKSETTINGS only using [gs]et_link_ksettings().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to specify through ethtool::rxnfc that a rule location is
special and will be used to participate in Wake-on-LAN, by e.g: having a
specific pattern be matched. When this is the case, fs->ring_cookie must
be set to the special value RX_CLS_FLOW_WAKE.
We also define an additional ethtool::wolinfo flag: WAKE_FILTER which
can be used to configure an Ethernet adapter to allow Wake-on-LAN using
previously programmed filters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Android's header sanitization tool chokes on static inline functions having a
trailing semicolon, leading to an incorrectly parsed header file. While the
tool should obviously be fixed, also fix the header files for the two affected
functions: ethtool_get_flow_spec_ring() and ethtool_get_flow_spec_ring_vf().
Fixes: 8cf6f497de ("ethtool: Add helper routines to pass vf to rx_flow_spec")
Reporetd-by: Blair Prescott <blair.prescott@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the event where the device unexpectedly becomes unresponsive
for a long period of time, flow control mechanism may propagate
pause frames which will cause congestion spreading to the entire
network.
To prevent this scenario, when the device is stalled for a period
longer than a pre-configured timeout, flow control mechanisms are
automatically disabled.
This patch adds support for the ETHTOOL_PFC_STALL_PREVENTION
as a tunable.
This API provides support for configuring flow control storm prevention
timeout (msec).
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Cc: Michal Kubecek <mkubecek@suse.cz>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We use a two-step process to configure a filter with RSS spreading. First,
the RSS context is allocated and configured using ETHTOOL_SRSSH; this
returns an identifier (rss_context) which can then be passed to subsequent
invocations of ETHTOOL_SRXCLSRLINS to specify that the offset from the RSS
indirection table lookup should be added to the queue number (ring_cookie)
when delivering the packet. Drivers for devices which can only use the
indirection table entry directly (not add it to a base queue number)
should reject rule insertions combining RSS with a nonzero ring_cookie.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETH_RESET_AP to reset the application processor(s) inside the NIC
interface.
Current ETH_RESET_MGMT supports a management processor inside this NIC.
This is typically used for remote NIC management purposes.
Application processors exist inside some SmartNICs to run various
applications inside the NIC processor - be it a simple algorithm without
an OS to as complex as hosting multiple VMs.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many user space API headers are missing licensing information, which
makes it hard for compliance tools to determine the correct license.
By default are files without license information under the default
license of the kernel, which is GPLV2. Marking them GPLV2 would exclude
them from being included in non GPLV2 code, which is obviously not
intended. The user space API headers fall under the syscall exception
which is in the kernels COPYING file:
NOTE! This copyright does *not* cover user programs that use kernel
services by normal system calls - this is merely considered normal use
of the kernel, and does *not* fall under the heading of "derived work".
otherwise syscall usage would not be possible.
Update the files which contain no license information with an SPDX
license identifier. The chosen identifier is 'GPL-2.0 WITH
Linux-syscall-note' which is the officially assigned identifier for the
Linux syscall exception. SPDX license identifiers are a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne. See the previous patch in this series for the
methodology of how this patch was researched.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
deprecated the ethtool_cmd::transceiver field, which was fine in
premise, except that the PHY library was actually using it to report the
type of transceiver: internal or external.
Use the first word of the reserved field to put this __u8 transceiver
field back in. It is made read-only, and we don't expect the
ETHTOOL_xLINKSETTINGS API to be doing anything with this anyway, so this
is mostly for the legacy path where we do:
ethtool_get_settings()
-> dev->ethtool_ops->get_link_ksettings()
-> convert_link_ksettings_to_legacy_settings()
to have no information loss compared to the legacy get_settings API.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward Error Correction (FEC) modes i.e Base-R
and Reed-Solomon modes are introduced in 25G/40G/100G standards
for providing good BER at high speeds. Various networking devices
which support 25G/40G/100G provides ability to manage supported FEC
modes and the lack of FEC encoding control and reporting today is a
source for interoperability issues for many vendors.
FEC capability as well as specific FEC mode i.e. Base-R
or RS modes can be requested or advertised through bits D44:47 of
base link codeword.
This patch set intends to provide option under ethtool to manage
and report FEC encoding settings for networking devices as per
IEEE 802.3 bj, bm and by specs.
set-fec/show-fec option(s) are designed to provide control and
report the FEC encoding on the link.
SET FEC option:
root@tor: ethtool --set-fec swp1 encoding [off | RS | BaseR | auto]
Encoding: Types of encoding
Off : Turning off any encoding
RS : enforcing RS-FEC encoding on supported speeds
BaseR : enforcing Base R encoding on supported speeds
Auto : IEEE defaults for the speed/medium combination
Here are a few examples of what we would expect if encoding=auto:
- if autoneg is on, we are expecting FEC to be negotiated as on or off
as long as protocol supports it
- if the hardware is capable of detecting the FEC encoding on it's
receiver it will reconfigure its encoder to match
- in absence of the above, the configuration would be set to IEEE
defaults.
>From our understanding , this is essentially what most hardware/driver
combinations are doing today in the absence of a way for users to
control the behavior.
SHOW FEC option:
root@tor: ethtool --show-fec swp1
FEC parameters for swp1:
Active FEC encodings: RS
Configured FEC encodings: RS | BaseR
ETHTOOL DEVNAME output modification:
ethtool devname output:
root@tor:~# ethtool swp1
Settings for swp1:
root@hpe-7712-03:~# ethtool swp18
Settings for swp18:
Supported ports: [ FIBRE ]
Supported link modes: 40000baseCR4/Full
40000baseSR4/Full
40000baseLR4/Full
100000baseSR4/Full
100000baseCR4/Full
100000baseLR4_ER4/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: [RS | BaseR | None | Not reported]
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: [RS | BaseR | None | Not reported]
<<<< One or more FEC modes
Speed: 100000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 106
Transceiver: internal
Auto-negotiation: off
Link detected: yes
This patch includes following changes
a) New ETHTOOL_SFECPARAM/SFECPARAM API, handled by
the new get_fecparam/set_fecparam callbacks, provides support
for configuration of forward error correction modes.
b) Link mode bits for FEC modes i.e. None (No FEC mode), RS, BaseR/FC
are defined so that users can configure these fec modes for supported
and advertising fields as part of link autonegotiation.
Signed-off-by: Vidya Sagar Ravipati <vidya.chowdary@gmail.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each time a new speed is added, the bonding 802.3ad isn't updated. Add a
comment to remind the developer to update this driver.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let the bonding driver report the correct speed
of the underlaying interfaces, when they are IPoIB, the ethtool
function get_link_ksettings() in the IPoIB driver is implemented.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Suggested-by: Håkon Bugge <Haakon.Bugge@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch introduce support for 2500BaseT and 5000BaseT link modes.
These modes are included in the new IEEE 802.3bz standard.
Signed-off-by: Pavel Belous <pavel.s.belous@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For operation in cabling environments that are incompatible with
1000BASE-T, PHY device may provide an automatic link speed downshift
operation. When enabled, the device automatically changes its 1000BASE-T
auto-negotiation to the next slower speed after a configured number of
failed attempts at 1000BASE-T. This feature is useful in setting up in
networks using older cable installations that include only pairs A and B,
and not pairs C and D.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defines a generic API to get/set phy tunables. The API is using the
existing ethtool_tunable/tunable_type_id types which is already being used
for mac level tunables.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse was complaining when we went to prototype some code
using ethtool_cmd_speed_set and SPEED_100000, which uses
the upper 16 bits of __u32 speed for the first time.
CHECK
...
.../uapi/linux/ethtool.h:123:28: warning:
cast truncates bits from constant value (186a0 becomes 86a0)
The warning is actually bogus, as no bits are really lost, but
we can get rid of the sparse warning with this one small change.
Reported-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances ethtool link mode bitmap to include
missing interface modes for 1G/10G speeds
Changes:
1000baseX is the mode introduced to cover all 1G Fiber cases.
All modes under 1000BaseX i.e. 1000BASE-SX, 1000BASE-LX, 1000BASE-LX10
and 1000BASE-BX10 are not explicitly defined at this moment.
10G CR,SR,LR and ER link modes are included for 10G speed..
Issue:
ethtool on 1G/10G SFP port reports Base-T
as this port supports 1000baseX,10G CR, SR and LR modes.
root@tor-02$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: external
Auto-negotiation: off
Current message level: 0x00000000 (0)
Link detected: yes
After fix:
root@tor-02$ ethtool swp1
Settings for swp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
10000baseER/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: external
Auto-negotiation: off
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Vidya Sagar Ravipati <vidya@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT bit.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Ben Hutchings <bwh@kernel.org>
Cc: David Decotigny <decot@googlers.com>
Acked-By: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances ethtool link mode bitmap to include
25G/50G/100G speed along with interface modes
Signed-off-by: Vidya Sagar Ravipati <vidya@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates: commit 793cf87de9 ("ethtool: Set cmd field in
ETHTOOL_GLINKSETTINGS response to wrong nwords")
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INT_MAX needs limits.h in userland.
When ethtool.h is included by a userland app, we got the following error:
.../usr/include/linux/ethtool.h: In function 'ethtool_validate_speed':
.../usr/include/linux/ethtool.h:1471:18: error: 'INT_MAX' undeclared (first use in this function)
return speed <= INT_MAX || speed == SPEED_UNKNOWN
^
Fixes: e02564ee33 ("ethtool: make validate_speed accept all speeds between 0 and INT_MAX")
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DIV_ROUND_UP is defined in linux/kernel.h only for the kernel.
When ethtool.h is included by a userland app, we got the following error:
include/linux/ethtool.h:1218:8: error: variably modified 'queue_mask' at file scope
__u32 queue_mask[DIV_ROUND_UP(MAX_NUM_QUEUE, 32)];
^
Let's add a common definition in uapi and use it everywhere.
Fixes: ac2c7ad0e5 ("net/ethtool: introduce a new ioctl for per queue setting")
CC: Kan Liang <kan.liang@intel.com>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a new ETHTOOL_GLINKSETTINGS/SLINKSETTINGS API,
handled by the new get_link_ksettings/set_link_ksettings callbacks.
This API provides support for most legacy ethtool_cmd fields, adds
support for larger link mode masks (up to 4064 bits, variable length),
and removes ethtool_cmd deprecated
fields (transceiver/maxrxpkt/maxtxpkt).
This API is deprecating the legacy ETHTOOL_GSET/SSET API and provides
the following backward compatibility properties:
- legacy ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks.
- legacy ethtool with new get/set_link_ksettings drivers: the new
driver callbacks are used, data internally converted to legacy
ethtool_cmd. ETHTOOL_GSET will return only the 1st 32b of each link
mode mask. ETHTOOL_SSET will fail if user tries to set the
ethtool_cmd deprecated fields to
non-0 (transceiver/maxrxpkt/maxtxpkt). A kernel warning is logged if
driver sets higher bits.
- future ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks, internally converted to new data
structure. Deprecated fields (transceiver/maxrxpkt/maxtxpkt) will be
ignored and seen as 0 from user space. Note that that "future"
ethtool tool will not allow changes to these deprecated fields.
- future ethtool with new drivers: direct call to the new callbacks.
By "future" ethtool, what is meant is:
- query: first try ETHTOOL_GLINKSETTINGS, and revert to ETHTOOL_GSET if
fails
- set: query first and remember which of ETHTOOL_GLINKSETTINGS or
ETHTOOL_GSET was successful
+ if ETHTOOL_GLINKSETTINGS was successful, then change config with
ETHTOOL_SLINKSETTINGS. A failure there is final (do not try
ETHTOOL_SSET).
+ otherwise ETHTOOL_GSET was successful, change config with
ETHTOOL_SSET. A failure there is final (do not try
ETHTOOL_SLINKSETTINGS).
The interaction user/kernel via the new API requires a small
ETHTOOL_GLINKSETTINGS handshake first to agree on the length of the link
mode bitmaps. If kernel doesn't agree with user, it returns the bitmap
length it is expecting from user as a negative length (and cmd field is
0). When kernel and user agree, kernel returns valid info in all
fields (ie. link mode length > 0 and cmd is ETHTOOL_GLINKSETTINGS).
Data structure crossing user/kernel boundary is 32/64-bit
agnostic. Converted internally to a legal kernel bitmap.
The internal __ethtool_get_settings kernel helper will gradually be
replaced by __ethtool_get_link_ksettings by the time the first
"link_settings" drivers start to appear. So this patch doesn't change
it, it will be removed before it needs to be changed.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new ioctl ETHTOOL_PERQUEUE for per queue parameters setting.
The following patches will enable some SUB_COMMANDs for per queue
setting.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices these days can have any speed and as was recently pointed out
any speed from 0 to INT_MAX is valid so adjust speed validation to
accept such values.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many virtual and not quite virtual devices allow any speed to be set
through ethtool. In particular, this applies to the virtio-net devices.
Document this fact to make sure people don't assume the enum lists all
possible values. Reserve values greater than INT_MAX for future
extension and to avoid conflict with SPEED_UNKNOWN.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions which check if the speed/duplex are defined.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy