Enable power saving for RTS5250S as following steps:
1.Set 0xFE58 to enable clock power management.
2.Check cfg space whether support L1SS or not.
3.If support L1SS, set 0xFF03 to free clkreq.
4.When entering idle status, enable aspm
and set parameters for L1SS and LTR.
5.Wnen entering run status, disable aspm
and set parameters for L1SS and LTR.
If entering L1SS mode successfully,
electric current will be below 2mA.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rts522a(rts5227s) is derived from rts5227, and mainly same with rts5227.
Add it to file mfd/rts5227.c to support this chip.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix rts5227&5249 failed send buffer cmd after suspend,
PM_CTRL3 should reset before send any buffer cmd after suspend.
Otherwise, buffer cmd will failed, this will lead resume fail.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rtl8402 is much like rtl8411, so just add it to rtl8411.c
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add set pull control macro to reduce code for setting pull control, and
use a common init function to reduce code for rtl8411.c. So this patch
is used to just simplify code.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update copyright date, remove author address and add Roger Tseng.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Normally OEMs will set vendor setting to the config space of Realtek
card reader in BIOS stage. This patch reads the setting at the first,
and configure the internal registers according to it, to improve card
reader's compatibility condition.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding support of model RTL8411B. Since the model is similar to RTL8411,
differences are implemented in rtl8411.c.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
RTS5249 supports SD UHS-II interface.
In order to support SD UHS-II，the definitions of some internal
registers of RTS5249 have to be modified and are different from its
predecessors. So we need this patch to ensure RTS5249 can work, even
SD/MMC stack doesn't support UHS-II interface.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Support new model RTS5227.
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In function rtsx_pci_switch_clock, some variables, such as min_n, max_n,
and max_div, are not necessary. And those assigned values look very
obscure for others. It's more proper to use macro definitions here to
replace these variables.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Acked-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rui Feng