This patch adds suspend-to-ram support for S5PV210.
Note. This patch is confirmed on SMDKV210 and SMDKC110 board.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error by S3C2410 PM Suspend debug option
due to undefined address.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Samsung S5P SoCs have the same interrupt type defines for both
external interrupts and gpio interrupts. This patch removes all
duplicates from S5PC100 and S5PV210 specific includes as well as
gpio interrupt code and put a common defines to plat/irqs.h
NOTE: Do not use this for S5P6440 and S5P6450.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: add note for S5P64X0]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds a common callback for gpio_to_irq() for external and
gpio interrupts for Samsung SoCs.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: moved samsung_gpiolib_to_irq() for s3c24xx build]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves external interrupt definitions from mach/gpio.h
to mach/regs-gpio.h for consistency with S5PV210.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PC100 SoC can use common S5P GPIO interrupt code. This patch
removes specific S5PC100 gpio interrupts code and adds required
defines and code to make use of common S5P code.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV210/S5PC110 can use common S5P GPIO interrupt code.
This patch adds required defines and code to make use of it.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds common code to enable support of GPIO interrupt on
S5P SoCs.
The total number of GPIO pins is quite large on S5P SoCs. Registering
irq support for all of them would be a resource waste. Because of that
the interrupt support for standard GPIO pins is registered dynamically
by the s5p_register_gpio_interrupt() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add the necessary definitions and mapping information to enable the
s3c-hsotg gadget to build.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for MMC power regulators on Samsung
Goni board. GPIO pin GONI_EXT_FLASH_EN has been transferred from machine
startup code to fixed voltage regulator.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add required platform definitions for s3c-hsotg driver to enable usb
gadget support on Samsung Goni board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since commit 67a38950f0917aecfe1a3e46720d8bbb0020 there is no need
to set pixel clock for the s3c-fb driver's window information.
The correct pixel clock value can be automatically calculated from
the other screen parameters. This patch removes the redundant pixel clock
parameter.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Change the default upper_margin and vsync_len to get rid of repeated last
line on the display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
All the S5P series SoCs use the 'struct clksrc_clk' type to represent the
armclk. So the clk_arm clock instance available in the plat-s5p clock code
is not used in any of the S5P series SoCs.
This patch removes the unused clk_arm instance from plat-s5p clock code.
Reported-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes redundant selection PLAT_S5P in the CPU_S5P64XX config.
Because PLAT_S5P is selected if select ARCH_S5P64XX in the plat-s5p/Kconfig.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The selection PLAT_S5P is selected with plat-s5p/Kconfig.
So remove it form each CPU_S5PXXXX config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In case of S5PV310/S5PC210, it uses the SPARSEMEM as default memory
configuration. So moved to ARCH_S5PV310 config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In case of S5PV210/S5PC110, it uses the SPARSEMEM as default memory
configuration. So moved to ARCH_S5PV210 config.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds to support Torbreck board of aESOP community using
Samsung S5PV210 SoC.
Signed-off-by: Kyuho Choi <chlrbgh0@gmail.com>
Signed-off-by: Hyunchul Ko <ghcstop@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The physical address of SYSCON(System Controller) is wrong.
This patch fixs this wrong physical address value from 0x10020000 to 0x10010000.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
It is reported by Junseok Jung that using clz instruction is
better instead of using for-loop to find the interrupt source.
This patch modifies interrupt source searching code using __ffs().
The __ffs() is implemented using clz instruction.
Suggested-by: Junseok Jung <jundols.jung@samsung.com>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support Watchdog Timer for S5PV310 and S5PC210.
Signed-off-by: Jemings Ko <jemings@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support RTC for S5PV310 and S5PC210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Jemings Ko <jemings@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMC(DRAM Memory Controller) map_desc table.
Because some driver such as CPUFREQ need to access DMC register.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support keypad device to the GONI board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes source clocks of moutcore.
That should be clk_mout_apll instead of clk_sclk_apll.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds various special clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds video clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds various clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds SDMMC clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds enable and ctrlbit for struct clksrc_clk clk_vpllsrc
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds log messages of aclk_200, aclk_100, aclk_160, and
aclk_133. And adds clk_p.rate from calculated aclk_100.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds struct clk clk_sclk_usbphy0, _usbphy1, and _hdmiphy
for adding member of clkset_group_list.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds 'clkset_aclk' to use commonly. And removed struct
clksrc_sources clkset_aclk_200, clkset_aclk_100, clkset_aclk_160,
and clkset_aclk_133.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds CPU hotplug support for S5PV310/S5PC210.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates Kconfig of mach-s5pv310 for easily dividing S5PC210
and S5PV310 boards. S5PC210(MCP) machines and S5PV310 machines can be
build into one kernel, this will be provied/submitted when new defconfig
can be merged.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung SMDKC210 board support file. The SoC
of SMDKC210, S5PC210(MCP) is one of package option of S5PV310.
And because composition of SMDKC210 and SMDKV310 differs, need
SMDKC210 with SMDKV310.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add touchscreen device support for mach-mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for platform-lcd device for mach-mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for frame buffer device for mach-mini6410.
Patch also adds support for feature string parsing
for mini6410. The feature string is kernel command
line passed and currently lets select only LCD
configuration. At the moment there is support for
two LCD configurations - 4.3" and 7.0". Feature
parser is mach-mini2440 based.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add nand device support and mtd partition
table for mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for mini6410 board from FriendlyARM
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds suspend-to-ram support for SMDK2416 based on existing 2412 PM code
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 and S3C2416 has 12 GPIO banks (from A to M), increase
ARCH_NR_GPIOS for this architectures.
Also typo from previous commit has been fixed: CONFIG_CPU_S3C24XX
instead CONFIG_CPU_244X.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Since we can get both physical and virtual addresses from the addruart
macro, we can use this to establish the debug mappings.
In the case of CONFIG_DEBUG_ICEDCC, we don't need any mappings, but
may still need to setup r7 correctly.
Incorporating ASM changes from Nicolas Pitre <npitre@fluxnic.net>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
As mentioned in the comment right at the top, the first four fields
are directly accessed by assembly code in head.S. Move nr_irqs so the
comment is true again.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
It has been replaced with separate fields.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A bool will suffice. The default is little endian.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This does not seem to be implemented.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Defaults are "basic mode" for physical channels, and "logical source
logical destination" for logical channels.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
And keep it logical by default.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
And keep it low priority by default.
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
without this patch we get :
arch/arm/mach-imx/built-in.o: In function `eukrea_cpuimx27_init':
eukrea_mbimx27-baseboard.c:(.init.text+0x44c): undefined reference to `mxc_ulpi_access_ops'
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
this patch fix the following errors :
arch/arm/mach-mx3/mach-pcm037_eet.c:62: error: implicit declaration of function 'MXC_SPI_CS'
arch/arm/mach-mx3/mach-pcm037_eet.c:185: error: implicit declaration of function 'imx35_add_spi_imx0'
from the Kconfig pcm037 is i.MX31 based and not i.MX35 so replace
imx35_add_spi_imx0 by imx31_add_spi_imx0
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: remove unneeded #include <mach/spi.h>]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is only a partial revert of "ARM: mx3/mx31ads: fold board
header in its only user"
[commit ccfa7c2698)]
As some of the the board defines are also used in the cs89x0
ethernet driver by the i.MX31 ADS.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the attached patch allows SD to work on i.MX51 with Wolfram's drivers
Tested on i.MX51.
Based on original patch from: Richard Zhu <r65037@freescale.com>
Signed-off-by: Eric Bénard <eric@eukrea.com>
Without this exiting WFI can result in cache corruption.
Code taken from Freescale's 2.6.27 BSP and tested on i.MX35
Signed-off-by: Eric Bénard <eric@eukrea.com>
this patch fix the following errors :
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_SDMA_BASE_ADDR’ undeclared here (not in a function)
arch/arm/plat-mxc/devices/platform-imx-dma.c:44:
error: ‘MX25_INT_SDMA’ undeclared here (not in a function)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* get_rate_arm : when 400MHz clock is selected (cctl & 1<<14),
ARM clock is 400MHz (MPLL * 3 / 4) and not 800MHz
* get_rate_per : peripherals's clock is derived from AHB and not
from IPG (ref manual : figure 5-1)
* can2_clk : use the correct ID
* without this patch, peripherals getting their clock from PER
clocks work fine because of the 2 errors which fix themselves
(ARM clock x 2 and per clock actually based on IPG which is AHB/2)
but flexcan can't work as it gets its clock from IPG and thus
calculates its bitrate using a reference value which is twice
what it really is.
Signed-off-by: Eric Bénard <eric@eukrea.com>
During the reorganisation of the imx-i2c devices
(in 64de5ec168) the 3rd imx-i2c device
for the mx35 got lost. This patch adds the missing device.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add IRAM(Internal RAM) allocation functions using GENERIC_ALLOCATOR.
The allocation size is 4KB multiples to guarantee alignment. The
idea for these functions is for i.MX platforms to use them
to dynamically allocate IRAM usage.
Applies on 2.6.36-rc7
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add USB host device support for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add touchscreen device support for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add nand device support and mtd partition table
for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for frame buffer device for mach-real6410.
Patch also adds support for feature string parsing
for real6410. The feature string is kernel command
line passed and currently lets select only LCD
configuration. At the moment there is support for
two LCD configurations - 4.3" and 7.0". Feature
parser is mach-mini2440 based.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes build error about GPIO address due to
conflict of commit 4d914705 and 19a2c065.
- commit 4d914705: Fix on GPIO base addresses
- commit 19a2c065: Moves initial map for merging S5P64X0
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[ various fixes ]
Signed-off-by: Huang Ying <ying.huang@intel.com>
LKML-Reference: <1287036094.7768.291.camel@yhuang-dev>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes the platform device name from 's3c2416-nand' to
's3c2412-nand' so that S3C2416 can reuse the nand functionality
available on S3C2412.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch replaces the device name assignment method from string assignment
to set_name method for all s3c24xx machines and adds device core file.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the partition table as existing partition table have last
partition size fixed and can't utilize available memory proprly if size is
more than 64M.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds header <linux/sched.h> into the below files for build with
CONFIG_PREEMPT_NONE.
arch/arm/mach-s5p64x0/cpu.c
Signed-off-by: Seung-Chull Suh <sc.suh@samsung.com>
[kgene.kim@samsung.com: edited title and message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch removes s3c_gpio_lock/unlock to avoid acquiring the lock
recursively as lock is already acquired by calling function.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: removed useless variable due to this]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s5p64x0_sysclass should be used in place of the obselete s5p6440_sysclass.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix the touch screen device name from s3c64x0-adc to s3c64xx-adc.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates s5p64x0_defconfig and changes the name from
s5p6440_defconfig so that can support S5P6440 and S5P6450 with
one kernel.
Tested on SMDK6440(S5P6440) and SMDK6450(S5P6450).
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds UART serial port support for S5P6450 SoC.
The S5P6450 has 6 UARTs, so adds resource of UART4 and UART5.
And to fix membase which is in serial/samsung.c is from Ben Dooks.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch moves smdk6440 board file from mach-s5p6440 into the new
mach-s5p64x0 directory and adds smdk6450 board file.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves S5P6440 GPIO support files from mach-s5p6440
into the new mach-s5p64x0 for merge S5P6440 and S5P6450 SocS.
NOTE: Not supported S5P6450 GPIO yet. Will be supported soon.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds S5P6450 I2C support in the ARCH_S5P64X0. And
moves S5P6440 I2C support files into the mach-s5p64x0 together.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves DMA support files in the mach-s5p64x0
for S5P6440 and S5P6450 SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
This patch updates Audio and SPI for S5P6440 and S5P6450 SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
This patch updates regarding clock files for supporting S5P6440 and
S5P6450 with one kernel image. The mach-s5p64x0/clock.c is for common
of them and there are specific clock files for each SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds ARCH_S5P64X0 which can support S5P6440 and S5P6450 with
one kernel image. So moved some files of mach-s5p6440 into the new ARCH
directory mach-s5p64x0.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch updates the Kconfig and Makefile for the S5P6440 and S5P6450
machines. It also updates arch/arm/ Kconfig and Makefile to include for
support ARCH_S5P64X0 with one kernel image.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves some initial maps from plat-s5p to machine,
so that can merge mach-s5p6440 and mach-s5p6450.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves OneNAND device definitions from mach-s5pv210 to plat-s5p
so that can support it commonly.
Note: S5PC110 and S5PC210 have same OneNAND driver.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
The core code now initializes the requested number of interrupts and
sets the flags in irq_desc.status which are requested by the
architecture via ARCH_IRQ_INIT_FLAGS.
Add ARCH_IRQ_INIT_FLAGS and remove the loop which sets those flags
after the irq descriptors are allocated.
[ This patch should have been in the original irq rework and got
dropped accidentaly ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Commit b683de2b3 in linux-next as of 20101014 (genirq: Query
arch for number of early descriptors) seems to have broken
bootup on several ARM boards - my beagleboard gives the
following dump with earlyprintk:
NR_IRQS:402
Unable to handle kernel NULL pointer dereference at virtual
address 00000028 pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0 Not tainted
(2.6.36-rc7-next-20101014-linux-next-20101012+ #40) PC is at
init_IRQ+0x14/0x48 LR is at start_kernel+0x150/0x2c0
[...]
We seem to be using desc->status without assigning desc to
anything. Fix this by adding back the code that was originally
there.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
LKML-Reference: <1287077397-21781-1-git-send-email-gadiyar@ti.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
This patch adds support for the two first channels of
the TMU0 timer block on sh7372. One channel is used
for clock event, the other for clock source.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add AC97 audio support for Simplemachines Sim.One board.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add platform support for the EP93xx AC97 controller driver.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that HDMI videomodes have become optional, they can be safely removed from
ap4evb platform data, since anyway 720p seems to be the best supported mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch also registered global extal clocks to sh7372.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix this linux-next build failure that Stephen reported:
arch/arm/kernel/perf_event.c: In function 'armpmu_event_init':
arch/arm/kernel/perf_event.c:543: error: request for member 'num_events' in something not a structure or union
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: paulus <paulus@samba.org>
LKML-Reference: <20101014164925.4fa16b75.sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: relax ioremap prohibition (309caa9) for -final and -stable
ARM: 6440/1: ep93xx: DMA: fix channel_disable
cpuimx27: fix i2c bus selection
cpuimx27: fix compile when ULPI is selected
ARM: 6435/1: Fix HWCAP_TLS flag for ARM11MPCore/Cortex-A9
ARM: 6436/1: AT91: Fix power-saving in idle-mode on 926T processors
ARM: fix section mismatch warnings in Versatile Express
ARM: 6412/1: kprobes-decode: add support for MOVW instruction
ARM: 6419/1: mmu: Fix MT_MEMORY and MT_MEMORY_NONCACHED pte flags
ARM: 6416/1: errata: faulty hazard checking in the Store Buffer may lead to data corruption
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: iommu-load cam register before flushing the entry
Get mem and irq resources using platform helpers
- platform_get_base
- platform_get_irq
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the keypad controller in the Scroll Key Encoder (SKE)
module on the Nomadik family and the DB8500 SoC.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move SH-Mobile ARM systems over from the legacy
"clk" member of struct sh_timer_config to using
the device name and clkdev for clock matching.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces sh7372_late_devices which
should include all regular processor specific
platform devices.
Early platform devices for console and timers
should be put on the sh7372_early_devices list,
all other devices should be on sh7372_late_devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds spi->mode support for the AMBA pl022 driver and
allows spidev to correctly alter SPI modes. Unused fields used in
the pl022 header file for the pl022_config_chip have been removed.
The ab8500 client driver selects the data transfer size instead
of the platform data.
For platforms that use the amba pl022 driver, the unused fields
in the controller data structure have been removed and the .mode
field in the SPI board info structure is used instead.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
... but produce a big warning about the problem as encouragement
for people to fix their drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As noted by Michał Mirosław <mirqus@gmail.com>, the voltages should
cover the supported voltage range, or support only one voltage.
As all these boards are using a GPIO to enable the power, chances
are that only 3.3V cards are supported on these boards.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to round memory regions correctly -- specifically, we need to
round reserved region in the more expansive direction (lower limit
down, upper limit up) whereas usable memory regions need to be rounded
in the more restrictive direction (lower limit up, upper limit down).
This introduces two set of inlines:
memblock_region_memory_base_pfn()
memblock_region_memory_end_pfn()
memblock_region_reserved_base_pfn()
memblock_region_reserved_end_pfn()
Although they are antisymmetric (and therefore are technically
duplicates) the use of the different inlines explicitly documents the
programmer's intention.
The lack of proper rounding caused a bug on ARM, which was then found
to also affect other architectures.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4CB4CDFD.4020105@kernel.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When channel_disable() is called, it disables per channel interrupts and
waits until channels state becomes STATE_STALL, and then disables the
channel. Now, if the DMA transfer is disabled while the channel is in
STATE_NEXT we will not wait anything and disable the channel immediately.
This seems to cause weird data corruption for example in audio transfers.
Fix is to wait while we are in STATE_NEXT or STATE_ON and only then
disable the channel.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Leo Chen <leochen@broadcom.com>
LKML-Reference: <20100907125057.371771121@linutronix.de>
Most of the regulator data structures are local to the
board file, but not made static. Fix this.
Also make the nand partition table static.
This gets rid of all the sparse warnings for this file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
sparse irq sets up NR_IRQS_LEGACY irq descriptors and archs then go
ahead and allocate more.
Use the unused return value of arch_probe_nr_irqs() to let the
architecture return the number of early allocations. Fix up all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@elte.hu>
The driver can handle different revisions of the core
which vary only minorly.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the suggested workaround for OMAP3 regarding to sDMA draining
issue, when the channel is disabled on the fly.
This errata affects the following configuration:
sDMA transfer is source synchronized
Buffering is enabled
SmartStandby is selected.
The issue can be easily reproduced by creating overrun situation while
recording audio.
Either introduce load to the CPU:
nice -19 arecord -D hw:0 -M -B 10000 -F 5000 -f dat > /dev/null & \
dd if=/dev/urandom of=/dev/null
or suspending the arecord, and resuming it:
arecord -D hw:0 -M -B 10000 -F 5000 -f dat > /dev/null
CTRL+Z; fg; CTRL+Z; fg; ...
In case of overrun audio stops DMA, and restarts it (without reseting
the sDMA channel). When we hit this errata in stop case (sDMA drain did
not complete), at the coming start the sDMA will not going to be
operational (it is still draining).
This leads to DMA stall condition.
On OMAP3 we can recover with sDMA channel reset, it has been observed
that by introducing unrelated sDMA activity might also help (reading
from MMC for example).
The same errata exists for OMAP2, where the suggestion is to disable the
buffering to avoid this type of error.
On OMAP3 the suggestion is to set sDMA to NoStandby before disabling
the channel, and wait for the drain to finish, than configure sDMA to
SmartStandby again.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by : Manjunath Kondaiah G <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An errata workaround for omap24xx is not setting the buffering disable bit
25 what is the purpose but channel enable bit 7 instead.
Background for this fix is the DMA stalling issue with ASoC omap-mcbsp
driver. Peter Ujfalusi <peter.ujfalusi@nokia.com> has found an issue in
recording that the DMA stall could happen if there were a buffer overrun
detected by ALSA and the DMA was stopped and restarted due that. This
problem is known to occur on both OMAP2420 and OMAP3. It can recover on
OMAP3 after dma free, dma request and reconfiguration cycle. However, on
OMAP2420 it seems that only way to recover is a reset.
Problem was not visible before the commit c12abc0. That commit changed that
the McBSP transmitter/receiver is released from reset only when needed. That
is, only enabled McBSP transmitter without transmission was able to prevent
this DMA stall problem in receiving side and underlying problem did not show
up until now. McBSP transmitter itself seems to no be reason since DMA
stall does not recover by enabling the transmission after stall.
Debugging showed that there were a DMA write active during DMA stop time and
it never completed even when restarting the DMA. Experimenting showed that
the DMA buffering disable bit could be used to avoid stalling when using
source synchronized transfers. However that could have performance hit and
OMAP3 TRM states that buffering disable is not allowed for destination
synchronized transfers so subsequent patch will implement a method to
complete DMA writes when stopping.
This patch is based on assumtion that complete lock-up on OMAP2420 is
different but related problem. I don't have access to OMAP2420 errata but
I believe this old workaround here is put for a reason but unfortunately
a wrong bit was typed and problem showed up only now.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Manjunath Kondaiah G <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap2plus_defconfig doesn't boot up when built with CONFIG_PM
disabled on the latest linux-omap master. Below are the observations
1. OMAP3 reboots in the middle of boot
--------------------------------------------------
[ 0.000000] Calibrating delay loop... 494.72 BogoMIPS (lpj=1933312)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] Brought up 1 CPUs
[ 0.000000] SMP: Total of 1 processors activated (494.72 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
U-Boot 1.1.4 (Feb 11 2009 - 16:10:23)
OMAP3430-GP rev 2, CPU-OPP2 L3-165MHz
TI 3430SDP 1.0 Version + mDDR (Boot NOR)
DRAM: 128 MB
Flash: 128 MB
NAND:128 MiB
--------------------------------------------------
2. OMAP4 does a kernel PANIC
-------------------------------------
[ 0.000000] Calibrating delay loop... 1195.29 BogoMIPS (lpj=4669440)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c2, AUX_CTRL 0x0e050000
[ 0.000000] CPU1: Booted secondary processor
[ 0.000000] Brought up 2 CPUs
[ 0.000000] SMP: Total of 2 processors activated (2395.78 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] mux: Could not set signal i2c2_scl.i2c2_scl
[ 0.000000] mux: Could not set signal i2c2_sda.i2c2_sda
[ 0.000000] mux: Could not set signal i2c3_scl.i2c3_scl
[ 0.000000] mux: Could not set signal i2c3_sda.i2c3_sda
[ 0.000000] mux: Could not set signal i2c4_scl.i2c4_scl
[ 0.000000] mux: Could not set signal i2c4_sda.i2c4_sda
-------------------------------------
This is happening because 'omap_serial_init()' is hanging in the boot.
On OMAP3 the watchdog is generating reboot because devices_init doesn't
happens where as on OMAP4 it just hangs without reboot.
The uart clock is not getting enabled after omap_device_idle as part
of omap_serial_init.
The omap_device_idle(will disable the clock) then omap_uart_block_sleep()
should enable clock back disabled during the boot up phase.
But omap_uart_block_sleep() stuffed version is binded only under
CONFIG_PM and other version is just empty. Hence it is not enabling
clock back as expected
This patch adds uart clock enable code to omap_uart_block_sleep() function
built with CONFIG_PM disabled.
Thanks to Charulatha and Govindraj for their help on this debug.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 914bab936fe0388a529079679e2f137aa4ff548d (OMAP: mach-omap2: Fix
incorrect assignment warnings) changed a pointer from 'u32 *' to
'void *' without also fixing up the pointer arithmetic.
Fix the scratchpad offsets so they are byte offsets instead of
word offsets and thus work correctly with a void pointer base.
Special thanks to Jean Pihet for taking the time track down this
problem and propose an initial solution.
Tested with off-idle and off-suspend on 36xx/Zoom3 and 34xx/omap3evm.
Cc: Manjunath Kondaiah G <manjugk@ti.com>
Reported-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the perf-events backend from arch/arm/oprofile into
drivers/oprofile so that the code can be shared between architectures.
This allows each architecture to maintain only a single copy of the PMU
accessor functions instead of one for both perf and OProfile. It also
becomes possible for other architectures to delete much of their
OProfile code in favour of the common code now available in
drivers/oprofile/oprofile_perf.c.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
In preparation for moving the majority of this oprofile code into an
architecture-neutral place separate the architecture-independent code
into oprofile_perf_init() and oprofile_perf_exit().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
In preparation for moving the generic functions out of this file, give
the functions more general names (e.g. remove "arm" from the names).
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Make op_name_from_perf_id() global so that we have a way for each
architecture to construct an oprofile name for op->cpu_type. We need to
remove the argument from the function prototype so that we can hide all
implementation details inside the function.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
So the correct clock will be taken for each of the two independent
controllers.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Documentation/gpio.txt specifies that the value argument to
gpio_set_value() should be handled as a boolean (E.G. != 0 is high),
so use the same logic as in _set_direction().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX35 CPUs marked with "MCIMX357CJQ5C M99V CTHA0943B" are coming with bogus
L2 cache settings. If these settings are kept unmodified prior enabling the L2
cache the CPU runs amok immediately when its enabled.
This fix should not hurt already working CPUs, as they are using the written
register value already.
Its currently unknown if its possible to detect the production lot from the
software to fix only affected CPUs.
While at it, make sure that mxc_init_l2x0 is only executed on i.MX31/35
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes
arch/arm/mach-mx3/mach-cpuimx35.c:143: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-cpuimx35.c:148: warning: 'usbh1_pdata' defined but not used
when USB_ULPI is not selected.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on work done earlier by Sascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Eric Bénard <eric@eukrea.com>
[ukl: actually squash the two approaches together]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The number of counters for the registered pmu is needed in a few places
so provide a helper function that returns this number.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Move pin config to appropriate places and use it only if needed.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-By: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Up to now, only pxa2xx pcmcia driver is using the API. No other device driver
is using this API in PXA3xx or any other PXA silicons.
Restrict the scope only on pxa2xx and remove the implementation of pxa3xx. So
we can avoid oo much checking on cpuid after more pxa chips supported.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
get_clk_frequency_khz() is used in private cpufreq driver. In order to meet
the change of different pxa silicons, checking cpuid is introduced in
get_clk_frequency_khz(). While more pxa silicons are supported, the workload
of checking cpuid is higher.
So restrict the scope of get_clk_frequency_khz() on pxa2xx. Different pxa
silcions use different private cpufreq driver to avoid too much checking
on cpuid.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Defined I2C/ALARM pin definitions
DS1337 RTC alarm support is tied to RTC_INT_GPIO
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Support for Matrix keypad ESC, ENTER, LEFT, and RIGHT
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Added board defintion, header, and debug UART support.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Bringup tavorevb3 development platform. UART and PMIC are enabled.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
mach-mmp needs to clear wake event in order to clear the keypad interrupt
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
mach-mmp utilizes pxa27x_keypad code so we need to move header to
platform pxa directory.
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add the platform data for the IOMMUs found on the Qualcomm
msm8x60 SoC.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Register a driver for the MSM IOMMU devices and a driver
for the translation context devices. Set up the global
IOMMU registers and initialize the context banks.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add support for the IOMMUs found on the upcoming Qualcomm
MSM8x60 chips. These IOMMUs allow virtualization of the
address space used by most of the multimedia cores on these
chips.
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The MSM8X60 FFA contains different components than the MSM8X60 SURF,
and therefore requires a different ARCH type and machine ID.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The MSM8x60 has a different physical memory offset than other targets.
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Private Peripheral interrupts could be edge triggered or level triggered
depending on the platform. Initialize handlers for these in board file.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Some MSM targets don't select the debug UART in this way. For those we
need to disable this selection mechanism.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Need to add this until real clock support for 8x60 goes in, or else some
drivers won't compile.
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
On RUMI platform STIs are not enabled by default, contrary to the
GIC spec. The bits for STIs in the enable/enable clear registers
are also RW instead of RO. STIs need to be enabled at initialization
time.
Signed-off-by: Steve Muckle <smuckle@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The existing MSM irq entry macro is specific to a VIC
implementation. Renaming this makes room for irq support based on
other interrupt controllers.
Signed-off-by: Steve Muckle <smuckle@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Board configuration for MSM8X60 emulation on RUMI3.
Signed-off-by: Steve Muckle <smuckle@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Define the interrupt map in irq-8x60.h
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
IRQ assignments are different for MSM8X60 than other existing MSMs.
Signed-off-by: Steve Muckle <smuckle@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
MSM8X60 has different IO mappings than previous MSMs.
Signed-off-by: Steve Muckle <smuckle@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Some builds may not support the proc-comm interface with
the baseband processor.
Signed-off-by: Steve Muckle <smuckle@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The OMAP4 PandaBoard has EHCI port1 hooked up to an external
SMSC3320 transciever. GPIO 1 is used to power on the transceiver
and GPIO 62 for reset on the transceiver.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid possible crash if CONFIG_MMC_OMAP_HS is not set.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
remove the second hsmmc definition as it is only used on the
expansion header of the PandaBoard and can be mux for other
functions.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It seems these comments where accidentally added so remove them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
This is just a readability and debugging improvement. As selection bit in
DEVCONF register is cleared when using 96 MHz PRCM source and set when using
external CLKS pin, change definitions to be sync with these.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Fix bit clear. Now it clears all other bits than mask bit where it should
clear only it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Reduce the amount of debugging generated by default when unused clocks
are being disabled by the clock code. The previous code would only
generate debug-level messages, but some people who wished to run
production kernels with debug-level messages enabled reported that the
large number of clock disable messages were slowing boot. Now to
enable clock-by-clock disable messages, DEBUG needs to be defined in
mach-omap2/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tuukka Tikkanen <tuukka.tikkanen@nokia.com>
Cc: Tim Bird <tim.bird@am.sony.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Split plat-omap/common.c into three pieces:
1. the 32KiHz sync timer and clocksource code, which now lives in
plat-omap/counter_32k.c;
2. the OMAP2+ common code, which has been moved to mach-omap2/common.c;
3. and the remainder of the OMAP-wide common code, which includes the
deprecated ATAGs code and a deprecated video RAM reservation function.
The primary motivation for doing this is to move the OMAP2+-specific parts
into an OMAP2+-specific file, so that build breakage related to the
System Control Module code can be resolved.
Benoît Cousson <b-cousson@ti.com> suggested a new filename and found
some bugs in the counter_32k.c comments - thanks Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Previously the OMAP McBSP ASoC driver implemented CLKS switching by
using omap_ctrl_{read,write}l() directly. This is against policy; the OMAP
System Control Module functions are not intended to be exported to drivers.
These symbols are no longer exported, so as a result, the OMAP McBSP ASoC
driver does not build as a module.
Resolve the CLKS clock changing portion of this problem by creating a
clock parent changing function that lives in
arch/arm/mach-omap2/mcbsp.c, and modify the ASoC driver to use it.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, this symbol must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/* and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP ASoC McBSP code implemented CLKR and FSR signal muxing via
direct System Control Module writes on OMAP2+. This required the
omap_ctrl_{read,write}l() functions to be exported, which is against
policy: the only code that should call those functions directly is
OMAP core code, not device drivers. omap_ctrl_{read,write}*() are no
longer exported, so the driver no longer builds as a module.
Fix the pinmuxing part of the problem by removing calls to
omap_ctrl_{read,write}l() from the OMAP ASoC McBSP code and
implementing signal muxing functions in arch/arm/mach-omap2/mcbsp.c.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, these symbols must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/*, and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversion.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP3 clock tree already contains the infrastructure to support
clock framework-based McBSP functional clock source switching. But it
did not contain the clkdev aliases for the McBSP code to refer to the
parent clocks in an SoC integration-neutral way. So, add the clkdev
aliases for the parent clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the MCBSP_CLKS clock and the clksel structures needed to support clock
framework-based source switching for McBSPs 1-5. Also, add clkdev
aliases on the parent clocks for the McBSP source switching code, added
in a subsequent patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the MCBSP_CLKS clock and the clksel structures needed to support clock
framework-based source switching for McBSP 1 and 2. Also, add clkdev
aliases on the parent clocks for the McBSP source switching code, added
in a subsequent patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Conform the OMAP2420_CTRL_BASE macro name to the standard of the rest of the
OMAP*_CTRL_BASE macro names. This fixes a bug in the OMAP2420 SCM code that
prevented OMAP242X_CTRL_REGADDR from working.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, if, for example, CONFIG_ARCH_OMAP2420 is not selected, OMAP2420
board files can still be included in the build. This results in link errors:
arch/arm/mach-omap2/built-in.o: In function `omap_generic_map_io':
.../arch/arm/mach-omap2/board-generic.c:51: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_init':
.../arch/arm/mach-omap2/board-h4.c:330: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_map_io':
.../arch/arm/mach-omap2/board-h4.c:373: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_init':
.../arch/arm/mach-omap2/board-apollon.c:325: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_map_io':
.../arch/arm/mach-omap2/board-apollon.c:353: undefined reference to `omap2_set_globals_242x'
make: *** [.tmp_vmlinux1] Error 1
Fix this by making the boards depend on the Kconfig option for the
specific SoC that they use.
Also, while here, fix the mach-omap2/board-generic.c file to remove the
dependency on OMAP2420.
Charulatha Varadarajan <charu@ti.com> caught a typo - thanks Charu.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Charulatha Varadarajan <charu@ti.com>
With the omap-serial the device has changed from ttyS to ttyO as
the system may have both omap-serial and 8250 ports.
Note that systems using omap-serial need to be updated to use ttyO[012]
instead of ttyS[012] in the bootloader, CONFIG_CMDLINE, /etc/inittab,
and the root file system with mknod. Also you may need to add ttyO[012]
to /etc/securetty.
Signed-off-by: Tony Lindgren <tony@atomide.com>
As is done on OMAP3, check omap_uart_can_sleep() as one of the
pre-conditions for entering the idle loop. Without this check,
entering idle introduces large latencies on active UARTs, and is
especially noticable on serial console.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules which have 16bit registers can cause imprecise
aborts if a __raw_readl/writel is used to read/write 32 bits.
Add an additional flag to identify modules which have such
hard requirement, and handle it in the hwmod framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Inorder to avoid any assumptions from bootloader, the watchdog
timer module is reset during init. This enables the watchdog
timer.
Therefore, it is required to disable WDT after it is reset
during init. Otherwise the system would reboot as per the default
watchdog timer registers settings.
Later, when the watchdog driver is loaded, the watchdog timer settings
is adjusted as per the default timer_margin set in the driver and the
driver would supports the normal operations supported by OMAP watchdog
timer.
Signed-off-by: Charulatha V <charu@ti.com>
Reported-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
VMMC2 regulator is configured but it's not used for the IGEP v2, so
remove this regulator from board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are currently two versions of IGEP v2 board, this patch introduces a
function to detect the hardware revision of IGEP board.
--------------------------
| Id. | Hw Rev. | GPIO 28 |
--------------------------
| 0 | B/C | high |
| 1 | C | low |
--------------------------
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP v2 board has four leds, this patch allows control all
of these LEDs using the LED class if CONFIG_LEDS_GPIO is selected
or using the General Purpose Input/Output (GPIO) interface if
CONFIG_LEDS_GPIO is not selected.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO for various devices are missing from the board initialization.
This patch adds support for the VBUS and over current gpios. Without this
patch, input/outputs from these two sources are ignored.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family. More about this
board at www.igep.es.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated for the mmc changes and to be selected by default]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The keypad matrix variable declaration is not matching
with structure variable keymap declared in keypad_matrix.h.
Due to this, following sparse warnings are generated with omap3_defconfig.
arch/arm/mach-omap2/board-devkit8000.c:223:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-devkit8000.c:223:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-devkit8000.c:223:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-ldp.c:107:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-ldp.c:107:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-ldp.c:107:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3evm.c:472:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3evm.c:472:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3evm.c:472:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-3430sdp.c:114:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-3430sdp.c:114:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-3430sdp.c:114:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-cm-t35.c:568:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-cm-t35.c:568:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-cm-t35.c:568:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3stalker.c:415:13: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3stalker.c:415:13: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3stalker.c:415:13: got int static [toplevel] *<noident>
This patch modifies the variable keymap declaration as per declaration in matrix_keymap structure.
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-input@vger.kernel.org
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/plat-omap/sram.c:130:13: warning: symbol 'omap_detect_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:216:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:450:12: warning: symbol 'omap_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:348:12: warning: symbol 'omap242x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:369:12: warning: symbol 'omap243x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:425:12: warning: symbol 'omap34xx_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:441:12: warning: symbol 'omap44xx_sram_init' was not declared. Should it be static
arch/arm/plat-omap/mcbsp.c:36:6: warning: symbol 'omap_mcbsp_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:50:5: warning: symbol 'omap_mcbsp_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:65:6: warning: symbol 'omap_mcbsp_st_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:70:5: warning: symbol 'omap_mcbsp_st_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:1648:15: warning: symbol 'omap_st_add' was not declared. Should it be static?
arch/arm/plat-omap/fb.c:414:15: warning: symbol 'omapfb_reserve_sram' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:43:5: warning: symbol 'omap_verify_speed' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:61:14: warning: symbol 'omap_getspeed' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes miscellaneous sparse warnings in mach-omap2.
arch/arm/mach-omap2/board-am3517evm.c:141:17: warning: Initializer entry defined twice
arch/arm/mach-omap2/board-am3517evm.c:142:18: also defined here
arch/arm/mach-omap2/irq.c:50:35: warning: Using plain integer as NULL pointer
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due to non declaration of
static structures and variables.
Sparse warning logs fixed:
arch/arm/mach-omap2/control.c:88:6: warning: symbol 'omap3_secure_ram_storage' was not declared. Should it be static?
n
arch/arm/mach-omap2/timer-gp.c:50:22: warning: symbol 'gptimer_wakeup' was not declared. Should it be static?
arch/arm/mach-omap2/timer-gp.c:240:18: warning: symbol 'omap_timer' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:121:24: warning: symbol 'prcm_context' was not declared. Should it be static?
arch/arm/mach-omap2/mux2420.c:510:29: warning: symbol 'omap2420_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux2430.c:589:29: warning: symbol 'omap2430_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:934:28: warning: symbol 'omap3_cus_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1080:29: warning: symbol 'omap3_cus_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1272:28: warning: symbol 'omap3_cbb_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1393:29: warning: symbol 'omap3_cbb_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1603:28: warning: symbol 'omap36xx_cbp_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1821:29: warning: symbol 'omap36xx_cbp_ball' was not declared. Should it be static?
arch/arm/mach-omap2/pm-debug.c:165:15: warning: symbol 'pm_dbg_dir' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:587:30: warning: symbol 'ads7846_config' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:606:23: warning: symbol 'omap3evm_spi_board_info' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:46:25: warning: symbol 'rx51_sdrc_params' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:211:25: warning: symbol 'rx51_get_sdram_timings' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3touchbook.c:64:15: warning: symbol 'touchbook_revision' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:350:24: warning: symbol 'am3517_evm_dss_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3stalker.c:567:23: warning: symbol 'omap3stalker_spi_board_info' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recent clean of i.MX devices registration changed the i2C bus number
selected for our platform (Freescale start peripheral ID at 1, kernel
now start it at 0 so i.MX27's i2c 1 is kernel's i2c 0).
Without this fix, i2c is unusable on this platform.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
without this patch we get :
arch/arm/mach-imx/built-in.o: In function `eukrea_cpuimx27_init':
eukrea_mbimx27-baseboard.c:(.init.text+0x44c): undefined reference to `mxc_ulpi_access_ops'
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add some additional documentation on register usage in __enable_mmu
to help complete the overall picture.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move these two functions, both of which are required for secondary
CPU booting, into the cpuinit section. Ensure bad processors call
__error_p for better diagnostics, rather than just __error.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__enable_mmu is required to be executed in an identity mapped region
to ensure that variances in CPUs do not cause a crash. We currently
achieve this by assuming that it will be co-located with
__create_page_tables. With hotplug CPU support, this assumption
becomes invalid. Implement a better solution which ensures that
it will be appropriately mapped no matter where it is placed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__error and __error_p may be used by secondary CPUs, so these
need to be in the cpuinit section.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move these functions, which are only ever used during boot CPU
initialization, to the init section.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When hotplug CPU is enabled, we need to keep the list of supported CPUs,
their setup functions, and __lookup_processor_type in place so that we
can find and initialize secondary CPUs. Move these into the __CPUINIT
section.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the entire kernel image available for secondary CPUs rather
than just the first MB of memory. This allows the startup code
to appear in the cpuinit sections.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
nommu can jump directly to __mmap_switched without the absolute
address branching which the mmuful kernel does.
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patches the condensed RealView SMP defconfig activating the
same 2.6.36 features mentioned in the vanilla RealView defconfig patch
submitted earlier.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patches the condensed RealView defconfig activating some
stuff that has been missing from this config for some time and
some stuff that was merged in the 2.6.36 merge window:
- The new character LCD driver is enabled
- The Versatile I2C is enabled
- The PL022 SPI driver is enabled
- gpiolib is enabled (and makes MMC detection work properly)
- The new LEDs code is enabled with a heartbeat trigger
- The RTC class is enabled, and the PL031 RTC (onchip) and
the offchip DS1307 on I2C is enabled
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order for CPUidle to work on SMP systems, an implementation of
cpu_idle_wait() is needed.
This patch duplicates the x86 implementation of cpu_idle_wait() for
ARM.
Tested-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Broadcast should not be needed when running SMP kernel on UP systems.
Also, this fixes an undefined instruction for SMP_ON_UP on earlier ARM
cores without the extended CPUID_EXT_MMFR3 register.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 14eff18126 added proper
detection for ARM11MPCore/Cortex-A9 instead of detecting them
as ARMv7. However, it was missing the HWCAP_TLS flags.
HWCAP_TLS is needed if support for earlier ARMv6 is compiled
into the same kernel. Without HWCAP_TLS flags the userspace
won't work unless nosmp is specified:
Kernel panic - not syncing: Attempted to kill init!
CPU0: stopping
<c005d5e4>] (unwind_backtrace+0x0/0xec) from [<c004c2f8>] (do_IPI+0xfc/0x184)
<c004c2f8>] (do_IPI+0xfc/0x184) from [<c03f25bc>] (__irq_svc+0x9c/0x160)
Exception stack(0xc0565f80 to 0xc0565fc8)
5f80: 00000001 c05772a0 00000000 00003a61 c0564000 c05cf500 c003603c c0578600
5fa0: 80033ef0 410fc091 0000001f 00000000 00000000 c0565fc8 c00b91f8 c0057cb4
5fc0: 20000013 ffffffff
[<c03f25bc>] (__irq_svc+0x9c/0x160) from [<c0057cb4>] (default_idle+0x30/0x38)
[<c0057cb4>] (default_idle+0x30/0x38) from [<c005829c>] (cpu_idle+0x9c/0xf8)
[<c005829c>] (cpu_idle+0x9c/0xf8) from [<c0008d48>] (start_kernel+0x2a4/0x300)
[<c0008d48>] (start_kernel+0x2a4/0x300) from [<80008084>] (0x80008084)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to Atmel, their 926T processors (AT91 post RM9200) requires
'Wait for Interrupt' mode be entered right after disabling the processor clock
in order to minimise current consumption when idle, so do both provided we're
not running on a 920T (an RM9200).
Furthermore, get rid of the #ifndef CONFIG_DEBUG_KERNEL, since arch_idle()
can be turned off completely with the kernel parameter 'nohlt'.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The kernel does not compile for my ARM926EJ-S system U300 due to
the isb instruction inserted in generic assember statement from
commit 8925ec4c53, "ARM: 6385/1:
setup: detect aliasing I-cache when D-cache is non-aliasing"
hey the isb is only available when assembling for v7 so let's
use the generic isb() macro from setup.h instead.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In case the pxa3xx-u2d driver isn't used, probing of ohci-pxa27x will cause an
ugly kernel crash (NULL pointer dereference in pxa3xx_u2d_start_hc(), because
struct u2d is NULL and clk_enable() call will crash the kernel, trying to access
it).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
USB2.0 Device Controller (U2DC) which is found in Marvell PXA3xx.
U2DC supports both High and Full speed modes.
PXA320 and PXA300 U2DC supports only UTMI interface.
PXA310 U2DC supports only ULPI interface and has the OTG capability.
U2D Controller ULPI driver introduced in this patch supports only the
PXA310 USB Host via the ULPI.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Fix typo in commit dbe3039 ("memblock/arm: Use memblock_region_is_memory()
for omap fb") - it should be memblock_is_region_memory().
Reported-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: ext Grazvydas Ignotas <notasas@gmail.com>
LKML-Reference: <4CABFADA.9020305@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Serial drivers call get_clock() very early, before platform bus
has been set up, this requires a special check to let them get
a proper clock. Without this patch, a serial console is broken
on S5PV310 and S5PC210 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: fix coding-style]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
This patch adds header <linux/sched.h> into the below files for build with
CONFIG_PREEMPT_NONE.
arch/arm/mach-s5p6440/cpu.c
arch/arm/mach-s5p6442/cpu.c
arch/arm/mach-s5pc100/cpu.c
arch/arm/mach-s5pv210/cpu.c
Following is error message of in case of s5pv210_defconfig with CONFIG_PREEMPT_NONE.
arch/arm/mach-s5pv210/cpu.c:91: error: implicit declaration of function 'need_resched'
Signed-off-by: SeungChull Suh <sc.suh@samsung.com>
[kgene.kim@samsung.com: removed mach-s5p64x0/cpu.c]
[kgene.kim@samsung.com: added fix mach-s5p6440/cpu.c]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes following unused codes for removing build warnings.
arch/arm/plat-samsung/adc.c:438: warning: unused variable 'flags'
arch/arm/mach-s5pv210/clock.c:176: warning: 's5pv210_clk_ip4_ctrl' defined but not used
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
All platform data has to be made conditional on CONFIG_STEDMA40
or we can provide a simple dummy filter functions as to avoid
cluttering the code with other #ifdef:s.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove obsolete pre_transfer hook in stedma40_chan_cfg. The
intent of this hook is merely to handle burst size
compensation for ux500 variant MMCI. Remove obsolete stedma40_set_psize
since it is only called from pre_transfer. DMAEngine device_control
replaces the functionality of stedma40_set_psize.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch add a LED class driver for LEDs found on the LaCie 2Big and
5Big Network v2 boards. The LEDs are wired to a CPLD and are controlled
through a GPIO extension bus.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Many Atmel SOC are embedding a MACB controller. This patch removes the long
dependency line for this Atmel MACB ethernet driver configuration entry.
The HAVE_NET_MACB configuration option is located in the net Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: David Miller <davem@davemloft.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
The simpler AT91x40 processors do not have the same power management
controller as the new AT91 devices. They do have a simpler power
controller module that we can use to disable the CPU clock at idle
time. Add code to support that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jongpill Lee