The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).
Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.
See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes problems with serial console break. When function
s3c64xx_serial_startup() was started while serial console has been working,
it caused lose of characters written to TX FIFO. This effect was particularly
observable with systemd, which closes serial port every time when it's
not currently needed, hence function s3c64xx_serial_startup() is called
quite often there. To fix this problem we avoid resetting TX FIFO if port is
used as serial console.
Example of broken console log:
[ 1086.7 Expecting device dev-ttySAC1.device...
[ 1086.[ OK ] Reached target Paths.
[ 1086.756416] s[ OK ] Reached target Swap.
[ 1086.776413] systemd[1]: Reached target Swap.
[ 1086.776642] systemd[1]: Starting Root Slice.
[ 5.53403[ OK ] Created slice Root Slice.
[ 5.548433] systemd[1]: Create[ OK ] Created slice User and Session Slice.
[ 5.568414] sys[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 5.588388] s[ OK ] Listening on Delayed Shutdown Socket.
[ 5.608376] sy[ OK ] Listening on Journal Socket (/dev/log).
[ 5.628361] [ OK ] Listening on udev Kernel Socket.
[ 5.648357] s[ OK ] Listening on udev Control Socket.
[ 5.668353] s[ OK ] Listening on Journal Socket.
[ 5.688366] systemd[1]: Listeni[ OK ] Created slice System Slice.
[ 5.708393] Mounting Temporary Directory...
[ 7139.067436] Starting prepare device daemon...
[ 7139.091726] sy Starting Generate environment from /etc/profile.d...
[ 5.792867] system Starting Create Static Device Nodes in /dev...
[ 7848.718 Mounting Debug File System...
[ 7848.7384 Mounting Configuration File System...
[ 5.852 Starting Apply Kernel Variables...
[ 5.8720 Starting Setup Virtual Console...
[ 7848.798 Starting udev Coldplug all Devices...
[ 7848.817 Starting Journal Service...
[ OK ] Started Journal Service.
[ 7848.854222] s[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems...
[ OK ] Mounted Configuration File System.
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed by Bluetooth hci_uart module to be able to change speed
of Bluetooth controller and local UART.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for Linux 4.1. Most
noteworthy:
- Add more Octeon-optimized crypto functions
- Octeon crypto preemption and locking fixes
- Little endian support for Octeon
- Use correct CSR to soft reset Octeons
- Support LEDs on the Octeon-based DSR-1000N
- Fix PCI interrupt mapping for the Octeon-based DSR-1000N
- Mark prom_free_prom_memory() as __init for a number of systems
- Support for Imagination's Pistachio SOC. This includes arch and
CLK bits. I'd like to merge pinctrl bits later
- Improve parallelism of csum_partial for certain pipelines
- Organize DTB files in subdirs like other architectures
- Implement read_sched_clock for all MIPS platforms other than
Octeon
- Massive series of 38 fixes and cleanups for the FPU emulator /
kernel
- Further FPU remulator work to support new features. This sits on a
separate branch which also has been pulled into the 4.1 KVM branch
- Clean up and fixes for the SEAD3 eval board; remove unused file
- Various updates for Netlogic platforms
- A number of small updates for Loongson 3 platforms
- Increase the memory limit for ATH79 platforms to 256MB
- A fair number of fixes and updates for BCM47xx platforms
- Finish the implementation of XPA support
- MIPS FDC support. No, not floppy controller but Fast Debug Channel :)
- Detect the R16000 used in SGI legacy platforms
- Fix Kconfig dependencies for the SSB bus support"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
MIPS: Makefile: Fix MIPS ASE detection code
MIPS: asm: elf: Set O32 default FPU flags
MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
MIPS: Kconfig: Disable SMP/CPS for 64-bit
MIPS: Hibernate: flush TLB entries earlier
MIPS: smp-cps: cpu_set FPU mask if FPU present
MIPS: lose_fpu(): Disable FPU when MSA enabled
MIPS: ralink: add missing symbol for RALINK_ILL_ACC
MIPS: ralink: Fix bad config symbol in PCI makefile.
SSB: fix Kconfig dependencies
MIPS: Malta: Detect and fix bad memsize values
Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
MIPS: Fix cpu_has_mips_r2_exec_hazard.
MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
MIPS: unaligned: Fix regular load/store instruction emulation for EVA
MIPS: unaligned: Surround load/store macros in do {} while statements
...
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
If the device node has a "big-endian" property and 32-bit registers, tell
the serial driver to use UPIO_MEM32BE instead of UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add cases for UPIO_MEM32BE wherever there are currently cases handling
UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Pull workqueue updates from Tejun Heo:
"Workqueue now prints debug information at the end of sysrq-t which
should be helpful when tracking down suspected workqueue stalls. It
only prints out the ones with something currently going on so it
shouldn't add much output in most cases"
* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Reorder sysfs code
percpu: Fix trivial typos in comments
workqueue: dump workqueues on sysrq-t
workqueue: keep track of the flushing task and pool manager
workqueue: make the workqueues list RCU walkable
* pnp:
PNP: Avoid leaving unregistered device objects in lists
PNP: Convert pnp_lock into a mutex
PNP: tty/serial/8250/8250_fintek: Use module_pnp_driver to register driver
PNP: platform/x86/apple-gmux: Use module_pnp_driver to register driver
PNP: net/sb1000: Use module_pnp_driver to register driver
PNP: media/rc: Use module_pnp_driver to register driver
PNP: ide/ide-pnp: Use module_pnp_driver to register driver
PNP: ata/pata_isapnp: Use module_pnp_driver to register driver
PNP: tpm/tpm_infineon: Use module_pnp_driver to register driver
PNP: Add helper macro for pnp_register_driver boilerplate
PNP / ACPI: Use ACPI_COMPANION_SET() during initialization
The result of netdev_priv is already implicitly cast to the type of the
left side of the assignment.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
@@
x =
- (T *)
netdev_priv(...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware is capable of inverting RTS signal when working
in RS-485 mode. Expose this functionality to user space.
Relay on a matching combination of standard flags
(SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND) to
detect when user space is requesting inverted RTS mode.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial ports of F81504/F81508/F81512 will failed when wakeup from S3(STR).
It's due to when the system wakeup from S3(STR), this PCI device's
configuration space from 0x40 to 0x40 + max_port * 0x08 should be
re-configured.
We move all initialization from pci_fintek_setup() to pci_fintek_init() and
set it to pci_serial_quirks .init section. It's will re-init this device when
system wakeup from pciserial_resume_ports().
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the expected behavior of kernel command lines of the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
and
earlycon=uart[8250],io|mmio|mmio32,<addr>[,options]
earlycon=uart[8250],<addr>[,options]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore undocumented behavior of kernel command line parameters of
the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
where 'options' have not been specified; in this case, the hardware
is assumed to be initialized.
Fixes: c7cef0a849 ("console: Add extensible console matching")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement KGDB IO operations for MIPS Fast Debug Channel (FDC). This can
be enabled via Kconfig, which also allows the channel number to be
chosen.
The magic sysrq hack is implemented in the TTY driver, detecting just ^C
for the KGDB channel, and ^O followed by a letter for the FDC console
channel.
The KGDB operations are reasonably efficient thanks to the flush
callback, with a 4 byte buffer being used in both directions to allow up
to 4 bytes to be encoded per FDC word. Reading of data for KGDB will
discard any data received on other channels, which clearly isn't ideal,
but given that there is a single FIFO shared between channels we can't
do much better.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9147/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for early console of MIPS Fast Debug Channel (FDC) on
channel 1 with a call very early from the MIPS setup_arch().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9145/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add TTY driver and consoles for the MIPS EJTAG Fast Debug Channel (FDC),
which is found on the per-CPU MIPS Common Device Mapped Memory (CDMM)
bus.
The FDC is a per-CPU device which is used to communicate with an EJTAG
probe. RX and TX FIFOs exist, containing 32-bits of data and 4-bit
channel numbers. 16 general data streams are implemented on this for TTY
and console use by encoding up to 4 bytes on each 32-bit FDC word.
The TTY devices are named e.g. /dev/ttyFDC3c2 for channel 2 of the FDC
attached to logical CPU 3.
These can be used for getting the kernel log, a login prompt, or as a
GDB remote transport, all over EJTAG and without needing a serial port.
It can have an interrupt to notify of when incoming data is available in
the RX FIFO or when the TX FIFO is no longer full. The detection of this
interrupt occurs in architecture / platform code, but it may be shared
with the timer and/or performance counter interrupt.
Due to the per-CPU nature of the hardware, all outgoing TTY data is
written out from a kthread which is pinned to the appropriate CPU.
The console is not bound to a specific CPU, so output will appear on the
chosen channel on whichever CPU the code is executing on. Enable with
e.g. console=fdc1 in kernel arguments. /dev/console is bound to the same
channel on the boot CPU's FDC if it exists.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9146/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specify transmit FIFO size which might be different depending on
LPUART instance. This makes sure uart_wait_until_sent in serial
core getting called, which in turn waits and checks if the FIFO
is really empty on shutdown by using the tx_empty callback.
Without the call of this callback, the last several characters
might not yet be transmitted when closing the serial port. This
can be reproduced by simply using echo and redirect the output to
a ttyLP device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exynos serial ports operate either in a DMA-based or interrupt-based
modes. In DMA-based mode, the UART generates a transfer data request
and a Transmission (Tx) interrupt in interrupt-based mode.
The Tx IRQ is only unmasked in interrupt-based mode and it was done
in s3c24xx_serial_start_tx(). Commit ba019a3e2a ("serial: samsung:
remove redundant interrupt enabling") removed the IRQ enable on that
function since it is enabled when the mode is set in enable_tx_pio().
The problem is that enable_tx_pio() is only called if the port mode
has not been set before but the mode was not cleared on .shutdown().
So if the UART was shutdown and then started up again, the mode set
will remain and the Tx IRQ won't be unmasked.
This caused a hang on at least Exynos5250, Exynos5420 and Exynos5800
when the system is rebooted or powered off.
Fixes: ba019a3e2a ("serial: samsung: remove redundant interrupt enabling")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only care if anything other than the lower 3 bits of the tty has
changed, so just check that way, which makes it a bit faster, and more
obvious what is going on. Also, document this for future developers to
understand why we did this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
The clock rate is requested from a property called
"clock-frequency" in both dw8250_probe_of and
dw8250_probe_acpi. Moving the requests to dw8250_probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having ACPI handle does not mean the same as having ACPI
identifier. The check is in any case useless, but having it
prevents this driver from being used for example with
multifunctional PCI devices, such as the newer Intel LPSS
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Tangier contains 4 HSUART ports as found on Intel Edison board which are
8250 compatible. The patch adds necessary bits to the driver.
Note that the HSU port0 is currently unavailable and thus not supported.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for intel_mid_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) nominator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
24 25 12 48000000 64000000 4000000(1)
49 50 14 49000000 56000000 3500000(1)
4 5 16 40000000 40000000 2500000(1)
16 25 16 32000000 32000000 500000(4),1000000(2),2000000(1)
24 25 16 48000000 48000000 1500000(2),3000000(1)
2304 3125 16 36864000 36864000 576000(4),1152000(2)
8192 15625 16 26214400 26214400 50(32768),200(8192)
9216 15625 16 29491200 29491200 1800(1024),57600(32),115200(16),
230400(8),460800(4),921600(2),1843200(1)
12288 15625 16 39321600 39321600 75(32768),150(16384),300(8192),
600(4096),1200(2048),2400(1024),4800(512),
9600(256),19200(128),38400(64)
45056 78125 16 28835840 28835840 110(16384)
274432 390625 16 3512729635127296 134(16384)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for byt_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) numerator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
4 5 16 80000000 80000000 2500000(2)
14 25 16 56000000 56000000 3500000(1)
16 25 16 64000000 64000000 500000(8),1000000(4),2000000(2),
4000000(1)
24 25 16 96000000 96000000 1500000(4),3000000(2)
2180 3103 16 70254592 70254592 134(32768)
2304 3125 16 73728000 73728000 576000(8),1152000(4)
8192 15625 16 52428800 52428800 50(65536),200(16384)
9216 15625 16 58982400 58982400 1800(2048),57600(64),115200(32),
230400(16),460800(8),921600(4),1843200(2)
12288 15625 16 78643200 78643200 75(65536),150(32768),300(16384),
600(8192),1200(4096),2400(2048),
4800(1024),9600(512),19200(256),38400(128)
9893 17154 16 57671680 57671680 110(32768)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"brd->nasync" amd "brd->maxports" are the same. They hold the number of
filled out channels in the brd->channels[] array. These tests should
be ">=" instead of ">" so that we don't read one element past the end.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_console_setup() checks port->mapbase != 0, but the port may
not be initialized yet even if this condition is met [e.g., ioremap()
may have failed]. Check port->membase != NULL instead, similar to
cdns_early_console_setup().
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of cdns_uart_readl() and cdns_uart_writel() and just call
readl() and writel() directly.
Most of the patch was created by search-and-replace (I had to convert a
few lines manually, and break some lines longer than 80 columns):
* s/cdns_uart_readl(/readl(port->membase + /g
* s/cdns_uart_writel(\([^,]*\),/writel(\1, port->membase +/g
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_get_port() sets port->iobase = 1 to "mark port in use", but
this "in use" condition is not checked anywhere else in the code. So
remove the line, keeping port->iobase = 0 (which also makes more sense).
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code assumes that the array cdns_uart_port[] has dimension
CDNS_UART_NR_PORTS, so let us define it this way.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register space size is 0x1000, and this value [not 0xfff] should be
provided to request_mem_region(), ioremap(), etc.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the 8250 driver reserve exactly the mmio region specified
in the devicetree. This prevents conflicts between UPIO_AU type
UARTs and other devices mapped closer than the default size of
0x1000 (or 0x100 for RT2880).
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a mapsize field to struct uart_port to be used in
conjunction with mapbase. If set, it overrides whatever value
serial8250_port_size() would otherwise report.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current calculation method in the case of 9600bps, rounding error occurs
has become setting that occur timeout faster than the required time. When we
use 9600bps, 32byte buffer, 10 bit (CS8) and 100 HZ, it becomes 3 jiffies
(30msec). In fact it is necessary 33msec. This updates to the calculation
that are not actually less than the value set by the rounding error.
Also, this is nothing will be calculated value when there is no load. If there
are a lot of case load, overrun error will occur immediately.
This is by the buffer size to be calculated twice the DMA buffer, and add the
change of setting a sufficient time-out value.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB can detect the overrun, but it does not support.
This adds overrun handling of SCIFA and SCIFB.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although clk_disable_unprepare() is called both on .remove()
and in .probe() error path, the clock is never actually enabled.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EFCR register contains RS-485 configuration which should not
be changed by shutdown. Instead of doing a write only update
the appropriate bits.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Soeren Grunewald