A few places use 'pcie_trans' which is a bit non-standard,
use 'trans_pcie' there as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places use just 'q', use 'rxq' there like all
other places.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The PCIe code has an array of buffer descriptors (RXBs) that have pages
and DMA mappings attached. In regular use, the array isn't used and the
buffers are either on the hardware receive queue or the rx_free/rx_used
lists for recycling.
Occasionally, during module unload, we'd see a warning from this:
WARNING: at lib/list_debug.c:32 __list_add+0x91/0xa0()
list_add corruption. prev->next should be next (c31c98cc), but was c31c80bc. (prev=c31c80bc).
Pid: 519, comm: rmmod Tainted: G W O 3.4.24-dev #3
Call Trace:
[<c10335b2>] warn_slowpath_common+0x72/0xa0
[<c1033683>] warn_slowpath_fmt+0x33/0x40
[<c12e31d1>] __list_add+0x91/0xa0
[<fdf2083c>] iwl_pcie_rxq_free_rbs+0xcc/0xe0 [iwlwifi]
[<fdf21b3f>] iwl_pcie_rx_free+0x3f/0x210 [iwlwifi]
[<fdf2dd7a>] iwl_trans_pcie_free+0x2a/0x90 [iwlwifi]
The reason for this seems to be that in iwl_pcie_rxq_free_rbs() we use
the array to free all buffers (the hardware receive queue isn't in use
any more at this point). The function also adds all buffers to rx_used
because it's also used during initialisation (when no freeing happens.)
This can cause the warning because it may add entries to the list that
are already on it. Luckily, this is harmless because it can only happen
when the entire data structure is freed anyway, since during init both
lists are initialized from scratch.
Disentangle this code and treat init and free separately. During init
we just need to put them onto the list after freeing all buffers (for
switching between 4k/8k buffers); during free no list manipulations
are necessary at all.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case that an AP/GO interface is started while there is a
station/P2P client associated, need to make sure that the AP/GO
beacon time is far enough from the station's one in oder to allow
the station to receive the DTIM beacons and the following traffic
etc.
To resolve this, when the AP is started, check if there is an
active station interface, and guarantee that the AP/GO TBTT is far
enough from the station one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add prints visible to the user when entering and exiting
thrermal throttling, because so users can tell that the
NIC is getting too hot (and throughput will decrease.)
Signed-off-by: eytan lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1x1 products will need a special LUT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Various parts of the HW code are applicable for
both v2.0 and v2.1.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver loads its firmware from files rtlwifi/rtl8723fw*.bin, but the
MODULE_FIRMWARE macros refer to rtlwifi/RTL8723aefw*.bin.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.8+]
Reported-by: Axel Köllhofer <AxelKoellhofer@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Map BIT 9 in TX DMA DWARD 0 as HW write back option.
We must turn on this option in the last TX descriptor,
this is required for old HW compatability.
This option indicate to HW that WB is required for this descriptor.
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vring index (MAC queue id) must be set in all TX descriptors
otherwise HW will fail to release descriptors for a specific vring
(disconnect or vring switch flows).
This is normally occurs when fragmentation required, if vring index
will not be the same for all SKB descriptors HW will fail to flush
this MAC queue.
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use common names instead of chip specific ones.
The patch contains no functional changes, but
it makes it easier to add support for further
descriptor sizes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different chipsets may use different TXWI descriptor
size. Instead of using a hardcoded value, use the
'queue->winfo_size' which holds the correct value for
a given device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code uses the same index value both
for the channel information array and for the TX
power table. The index starts from 14, however the
index of the TX power table must start from zero.
Fix it, in order to get the correct TX power value
for a given channel.
The changes in rt61pci.c and rt73usb.c are compile
tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch complains that this is a read past the end of the array. It
turns out we are printing the wrong array here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since platform support is required for WoW, identify and
and enable Wow only for supported cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of these relate to endianness problems, and are purely cosmetic.
But a couple of them were legit -- listen interval parsing and some of
the rate selection code would malfunction on BE systems.
There's still one cosmetic warning remaining, in the (admittedly) ugly
code in cw1200_spi.c. It's there because the hardware needs 16-bit SPI
transfers, but many SPI controllers only operate 8 bits at a time.
If there's a cleaner way of handling this, I'm all ears.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix to return -ENOMEM in the ipw_rx_queue_alloc() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_txqaddbuf assumes that all the linked buffers in the queue passed
to it are part of the same A-MPDU or MPDU. The CAB queue rework violates
this assumption, which can cause the internal queue depth to go
negative.
Fix this by increasing the counter for all slots of [bf, bf->bf_lastbf]
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This provides some of the same info found in
the ath9k_htc debugfs through the standard ethtool stats API.
This logic is only supported when ath9k_htc debugfs kernel
feature is enabled, since that is the only time stats
are actually gathered.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().
[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After receiving channel switch announcement from AP, scan and
association on that channel is blocked for DFS_CHAN_MOVE_TIME
(10 seconds). Hence station will be able to connect to the AP,
once it is moved to new channel.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to parse requested AP's 11h capabilities
and add 11h information in association request.
Also, deauth is sent to the AP after receiving channel switch
announcement event from firmware. This happens when AP advertises
WLAN_EID_CHANNEL_SWITCH IE in it's beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not unconditionally access the chan variable in
brcmf_cfg80211_mgmt_tx() as it may be NULL.
Use freq instead.
Introduced by c2ff8cad64
("brcm80211: make mgmt_tx in brcmfmac accept a NULL channel")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use negative check (if(!bss_desc)) and return failure
instead of failing a NULL check later in
mwifiex_check_network_compatibility() routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the
same condition twice. The problem was found using cppcheck-1.49, and the
proper fix was verified against the pre-mac80211 version of the code.
This patch was originally included as commit 1288aa4, but was accidentally
reverted in a later patch.
Reported-by: David Binderman <dcb314@hotmail.com> [original report]
Reported-by: Andrea Morello <andrea.merello@gmail.com> [report of accidental reversion]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org> [back to 2.6.39]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add scatter gather list support for better rx glom performance.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introducing a new SDIO block data access interface function
brcmf_sdio_buffrw. It will act as a unified interface function for any block
data access to WiFi dongle through SDIO interface. This patch enables
the support for single skb transmission.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is an ID table registered to SDIO stack which consists of all SDIO devices
supported by brcmfmac. It is not necessary to have an extra check.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of allocating an empty list item and queue that for
the dpc data worker to dequeue an atomic counter is used.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just cleaning up and being consistent in naming operations
related to struct brcmf_fws_mac_descriptor objects.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware-signalling code used NL80211_NUM_ACS, but it has
its own definition enum brcmf_fws_fifo, which is more appropriate
to use. This effectively removes the need to include nl80211.h.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The term prec (precedence) is different from the fifo number. Rename
use of prec with fifo to be consistent and clear.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware will sent an event message when bc/mc traffic should
be sent to the device using credit mechanism.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows writing MTD driver working as a platform driver. In
platform_data it will receive struct ssb_sflash, which contains all
important data about flash (window, size).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS198 and CUS230 are similar cards, both
are AR9485 + xLNA solutions. But, the subsystem IDs
differ - identify CUS230 explicitly to make things
clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the REGULATORY debug level to print the target power
details. EEPROM can be used for other purposes and this
spams the log.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg