In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a compensation phase to improve the accuracy of ADC
measurement. This is the built-in function through input half of the
reference voltage to get the ADC offset.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-10-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the function to set the sampling rate and keep the sampling period
for a driver used to wait the fresh value.
In addition, since the ADC clock is required when initializing the ADC
device, move clk_prepare_enable ahead of the initialization phase.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-9-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make driver to support ast2600 adc device.
- Use shared reset controller
- Complete the vref configure function
- Add the model data for ast2600 adc
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-7-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch uses need_prescaler and scaler_bit_width to set the ADC clock
scaler.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-5-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add documentation for the Senseair Sunrise 006-0-0007 CO2 NDIR sensor.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210920135413.140310-2-jacopo+renesas@jmondi.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver and device-tree also use vid-supply regulator.
Fixes: 7e000fbff7 ("dt-bindings: iio: magnetometer: ak8975: convert format to yaml, add maintainer")
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210913181949.83179-1-david@ixit.cz
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Most interesting element this time is the new chrdev based interface
for the counter subsystem. Affects all drivers. Some minor precursor
patches.
Major parts:
* Bring all the sysfs attribute setup into the counter core rather than
leaving it to individual drivers. Docs updates accompany these changes.
* Move various definitions to a uapi header as now needed from userspace.
* Add the chardev interface + extensive documentation and example tool
* Add new ABI needed to identify indexes needed for chrdev interface
* Implement new interface for the 104-quad-8
* Follow up deals with wrong path for documentation build
* Various trivial cleanups and missing feature additions related to this
series
-----BEGIN PGP SIGNATURE-----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=AaeD
-----END PGP SIGNATURE-----
Merge tag 'counter-for-5.16a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of counter subsystem new feature support for the 5.16 cycle
Most interesting element this time is the new chrdev based interface
for the counter subsystem. Affects all drivers. Some minor precursor
patches.
Major parts:
* Bring all the sysfs attribute setup into the counter core rather than
leaving it to individual drivers. Docs updates accompany these changes.
* Move various definitions to a uapi header as now needed from userspace.
* Add the chardev interface + extensive documentation and example tool
* Add new ABI needed to identify indexes needed for chrdev interface
* Implement new interface for the 104-quad-8
* Follow up deals with wrong path for documentation build
* Various trivial cleanups and missing feature additions related to this
series
* tag 'counter-for-5.16a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
docs: counter: Include counter-chrdev kernel-doc to generic-counter.rst
counter: fix docum. build problems after filename change
counter: microchip-tcb-capture: Tidy up a false kernel-doc /** marking.
counter: 104-quad-8: Add IRQ support for the ACCES 104-QUAD-8
counter: 104-quad-8: Replace mutex with spinlock
counter: Implement events_queue_size sysfs attribute
counter: Implement *_component_id sysfs attributes
counter: Implement signalZ_action_component_id sysfs attribute
tools/counter: Create Counter tools
docs: counter: Document character device interface
counter: Add character device interface
counter: Move counter enums to uapi header
docs: counter: Update to reflect sysfs internalization
counter: Update counter.h comments to reflect sysfs internalization
counter: Internalize sysfs interface code
counter: stm32-timer-cnt: Provide defines for slave mode selection
counter: stm32-lptimer-cnt: Provide defines for clock polarities
To avoid checking if fence exists multipled times, changed fence
handling to depend only on the fence status field:
Busy, which means CS still did not completed :
Add its QID so multi CS wait on its completion.
Finished, which means CS completed and fence exists:
Raise its completion bit if it finished mcs handling and
update if necessary the earliest timestamp.
Gone, which means CS already completed and fence deleted:
Update multi CS data to ignore timestamp and raise its
completion bit.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
No need to check the return value if the following action is the same for
both cases. In addition, now that hl_ctx_free() doesn't print if the
context is not released, its name can be misleading as the context might
stay alive after it is executed with no indication for that.
Hence we can discard it and simply put the refcount.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Remove the flag that determines whether to take a timestamp once the
interrupt arrives.
Instead, always take the timestamp once per interrupt.
This is a must for the user-space to measure its graph operations
to evaluate the graph computation time.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
When adding a new node to the hpriv list, the driver should
initialize its fields before adding the new node.
Otherwise, there may be some small chance of another thread traversing
that list and accessing the new node's fields without them being
initialized.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Make the frequency set/get functionality common to all ASICs.
This makes more code reusable when adding support for newer ASICs.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/misc/habanalabs/common/firmware_if.o: in function `hl_fw_dynamic_request_descriptor':
firmware_if.c:(.text.unlikely+0xc89): undefined reference to `crc32_le'
Fixes: 8a43c83fec ("habanalabs: load boot fit to device")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Implement the calls to the dma-buf kernel api to create a dma-buf
object backed by FD.
We block the option to mmap the DMA-BUF object because we don't support
DIRECT_IO and implicit P2P. We only implement support for explicit P2P
through importing the FD of the DMA-BUF.
In the export phase, we provide to the DMA-BUF object an array of pages
that represent the device's memory area. During the map callback,
we convert the array of pages into an SGT. We split/merge the pages
according to the dma max segment size of the importer.
To get the DMA address of the PCI bar, we use the dma_map_resources()
kernel API, because our device memory is not backed by page struct
and this API doesn't need page struct to map the physical address to
a DMA address.
We set the orig_nents member of the SGT to be 0, to indicate to other
drivers that we don't support CPU mappings.
Note that in Habanalabs's ASICs, the device memory is pinned and
immutable. Therefore, there is no need for dynamic mappings and pinning
callbacks.
Also note that in GAUDI we don't have an MMU towards the device memory
and the user works on physical addresses. Therefore, the user doesn't
pass through the kernel driver to allocate memory there. As a result,
only for GAUDI we receive from the user a device memory physical address
(instead of a handle) and a size.
We check the p2p distance using pci_p2pdma_distance_many() and refusing
to map dmabuf in case the distance doesn't allow p2p.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Gal Pressman <galpress@amazon.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
User process might want to share the device memory with another
driver/device, and to allow it to access it over PCIe (P2P).
To enable this, we utilize the dma-buf mechanism and add a dma-buf
exporter support, so the other driver can import the device memory and
access it.
The device memory is allocated using our existing allocation uAPI,
where the user will get a handle that represents the allocation.
The user will then need to call the new
uAPI (HL_MEM_OP_EXPORT_DMABUF_FD) and give the handle as a parameter.
The driver will return a FD that represents the DMA-BUF object that
was created to match that allocation.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When polling fences for multi CS, it is possible that fence is
no longer exists (its corresponding CS completed and the fence was
deleted) but we still accessing its parameters, causing NULL pointer
dereference.
Fixed by checking if fence exits before accessing its parameters.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Race condition occurs when CS fence completes and multi CS did not
completed yet, while waiting for multi CS ends and returns indication
to user that the CS completed. Next wait for multi CS may be triggered
by previous multi CS completion without any current CS completed,
causing an error.
Example scenario :
1. User do multi CS wait for CSs 1 and 2 on master QID 0
2. CS 1 and 2 reached the "cs release" code. The thread of CS 1
completed both the CS and multi CS handling but the completion
thread of CS 2 completed the CS but still did not executed
complete_multi_cs (note that in CS completion the sequence is to
first do complete all for the CS and then another complete all to
signal the multi_cs)
3. User received indication that CS 1 and 2 completed (since we check
the CS fence and both indicated as completed) and immediately waits
on CS 3 and 4, also on master QID 0.
4. Completion thread of CS2 executed complete_multi_cs before
completion of CS 3 and 4 and so will trigger the multi CS wait of
CSs 3 and 4 as they wait on master QID 0.
This will trigger multi CS completion although none of its
current CS has been completed.
Fixed by adding multi CS complete handling indication for each CS.
CS will be marked to the user as completed only if its fence completed
and multi CS handling is done.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
There may be a situation where drivers receives continuous fatal H/W
error events from FW immediately post reset cycle.
This may be due to some fault on the silicon itself.
In such case its better to bypass reset cycle so we won't be stuck in
endless loop of resets.
This commit bypasses reset request in case driver received two back to
back FW fatal error before first occurrence of heartbeat event.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Taking an accurate timestamp in a close proximity of the interrupt is
required for user side statistics management.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The driver allows only a single process to open a device's FD at any
single time. This is done by checking "hdev->compute_ctx" under mutex.
Therefore, to prevent a race between the moment a user closes it's FD
and when another user tries to open the device, we need to make sure
that clearing this variable is the very last thing that is done in the
code of the FD's release.
I'm moving the idle check before clearing this variable and the
"reset on device release". btw, if the reset happens it will prevent
any other user from opening the device until the reset is finished.
An important thing to note is that we need to remove the user process
that is closing the device from the process list BEFORE calling the
reset function. That is to prevent a case where the reset code will
try to kill that user process and it is unnecessary as the process
doesn't hold any device/driver resources anymore.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Reset to the device is not necessarily due to an error, so print it
as info instead of error.
In addition, print the type of reset we are doing:
- reset of the entire device (aka hard reset)
- reset of the device after user have released it (less than hard reset)
- lighter reset of an inference device (aka soft reset)
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Soft-reset is the procedure where we reset only the compute/DMA engines
of the device, without requiring the current user-space process to
release the device.
This type of reset can happen if TDR event occurred (a workload got
stuck) or by a root request through sysfs.
This is only relevant for inference ASICs, as there is no real-world
use-case to do that in training, because training runs on multiple
devices.
In addition, we also do (in certain ASICs) a reset upon device release.
That reset uses the same code as the soft-reset.
Therefore, to better differentiate between the two resets, it is better
to rename the soft-reset support as "inference soft-reset", to make
the code more self-explanatory.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
The translation in debugfs of device memory MMU virtual addresses was
wrong as it did not take into consideration the fact that the page
sizes there can be not power of 2.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
In order to avoid user target value wraparound, we modify the
current interface so user will be able to wait for an 8-byte
target value rather than a 4-byte value.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
During TDR handling, we check multiple times if CS is valid.
No need to perform this check as CS must be valid at all time
during the TDR handling.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Add support to retrieve following power info via HWMON:
- instantaneous power value
- highest value since last reset
- reset the highest place holder
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of having dedicated function per message that we want to send
to the firmware in COMMS protocol, have a generic function that we can
call to from other parts of the driver
Signed-off-by: Alon Mizrahi <amizrahi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Instead of using the Linux kernel HWMON enums definition when
communicating with the firmware, use proprietary HWMON based enums
i.e. map hwmon.h header enum to cpucp_if.h based enum while.
This is needed because the HWMON enums are not forcing backward
compatibility and therefore changes can break compatibility between
newer driver and older firmware.
The driver will check for CPU_BOOT_DEV_STS0_MAP_HWMON_EN bit to
validate if f/w supports cpucp->hwmon enum mapping to support older
firmware where this mapping won't be available.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Command submission timeout is currently determined during driver
loading time. As some environments requires this timeout to be
modified in runtime, we introduce a new debugfs node that controls
the timeout value without the need to reload the driver.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
2 fixes for this cycle:
* Fix a null pointer dereference in ahci-platform driver (from Hai)
* Fix uninitialized variables in pata_legacy driver (from Dan)
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCYWzTkAAKCRDdoc3SxdoY
ductAQCNJ4xNuZVaFFiwvrQOn16xQsu/UHnBReqdBBLytSaW1wD+IjAKEaOYVTbU
0nLtzNSxV52N6o6xSouUT7vxVJ7kjQI=
=H02G
-----END PGP SIGNATURE-----
Merge tag 'libata-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull libata fixes from Damien Le Moal:
"Two fixes for this cycle:
- Fix a null pointer dereference in ahci-platform driver (from Hai)
- Fix uninitialized variables in pata_legacy driver (from Dan)"
* tag 'libata-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: ahci_platform: fix null-ptr-deref in ahci_platform_enable_regulators()
pata_legacy: fix a couple uninitialized variable bugs
-----BEGIN PGP SIGNATURE-----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=J/e4
-----END PGP SIGNATURE-----
Merge tag 'block-5.15-2021-10-17' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Bigger than usual for this point in time, the majority is fixing some
issues around BDI lifetimes with the move from the request_queue to
the disk in this release. In detail:
- Series on draining fs IO for del_gendisk() (Christoph)
- NVMe pull request via Christoph:
- fix the abort command id (Keith Busch)
- nvme: fix per-namespace chardev deletion (Adam Manzanares)
- brd locking scope fix (Tetsuo)
- BFQ fix (Paolo)"
* tag 'block-5.15-2021-10-17' of git://git.kernel.dk/linux-block:
block, bfq: reset last_bfqq_created on group change
block: warn when putting the final reference on a registered disk
brd: reduce the brd_devices_mutex scope
kyber: avoid q->disk dereferences in trace points
block: keep q_usage_counter in atomic mode after del_gendisk
block: drain file system I/O on del_gendisk
block: split bio_queue_enter from blk_queue_enter
block: factor out a blk_try_enter_queue helper
block: call submit_bio_checks under q_usage_counter
nvme: fix per-namespace chardev deletion
block/rnbd-clt-sysfs: fix a couple uninitialized variable bugs
nvme-pci: Fix abort command id
-----BEGIN PGP SIGNATURE-----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=4wXI
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.15-2021-10-17' of git://git.kernel.dk/linux-block
Pull io_uring fix from Jens Axboe:
"Just a single fix for a wrong condition for grabbing a lock, a
regression in this merge window"
* tag 'io_uring-5.15-2021-10-17' of git://git.kernel.dk/linux-block:
io_uring: fix wrong condition to grab uring lock
Fixes up some issues in rc5.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmFm1OcPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpp0AIAL5lvwd/Dzj0trDEOm93yTiKigkllJ9if8pF
G3V6IgyyeNujmEJLD2Fz5GPUVXg5G2+Yh2xgf8OP4syS/pZoCGkGcLIoo7lJRSvz
D3KpNYrZ2O1kFw2XWP3p7O/H8pxWAMPjykRaVoniCd+rIIpRzWdYBDDWConUGqC1
IlB5BS6cv3vRIoJ4Ac3YVOEUM4WOw/2fwzxejVjxQdNjgbWL0JBY1IBiJrfp7iEo
L3KRmN25JWCwE0x+Ehy6/uSalVzPgjESBYzrBFihnFXDS/LIIIXuRb9Q3HzEFFHT
UhccuExc8Nq8JDKWrZkYP2s950Gnv249bC9tqlHHTnoE+pxG3Ms=
=i68W
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Fixes up some issues in rc5"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-vdpa: Fix the wrong input in config_cb
VDUSE: fix documentation underline warning
Revert "virtio-blk: Add validation for block size in config space"
vhost_vdpa: unset vq irq before freeing irq
virtio: write back F_VERSION_1 before validate
Fix a bug where guests on P9 with interrupts passed through could get stuck in
synchronize_irq().
Fix a bug in KVM on P8 where secondary threads entering a guest would write outside their
allocated stack.
Fix a bug in KVM on P8 where secondary threads could confuse the host offline code and
cause the guest or host to crash.
Thanks to: Cédric Le Goater
-----BEGIN PGP SIGNATURE-----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=fPMr
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a bug where guests on P9 with interrupts passed through could get
stuck in synchronize_irq().
- Fix a bug in KVM on P8 where secondary threads entering a guest would
write outside their allocated stack.
- Fix a bug in KVM on P8 where secondary threads could confuse the host
offline code and cause the guest or host to crash.
Thanks to Cédric Le Goater.
* tag 'powerpc-5.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Make idle_kvm_start_guest() return 0 if it went to guest
KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()
powerpc/xive: Discard disabled interrupts in get_irqchip_state()
Billy Tsai