This reverts commit e0371298dd. It was
accidently applied despite discussion still going on.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Stephen Boyd <swboyd@chromium.org>
IC_DATA_CMD[11] indicates the first data byte received after the address
phase for receive transfer in Master receiver or Slave receiver mode,
this bit was set in some transfer flow. IC_DATA_CMD[7:0] contains the
data to be transmitted or received on the I2C bus, so we should use the
lower 8 bits to get the real data length.
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The brcmstb_send_i2c_cmd currently has a condition that is (CMD_RD ||
CMD_WR) which always evaluates to true, while the obvious fix is to test
whether the cmd variable passed as parameter holds one of these two
values.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
Pull i2c updates from Wolfram Sang:
- mostly driver updates. Bigger ones for mlxcpld and iproc. But most of
them are all over the place.
- removal of the efm32, sirf, u300, and zte zx bus drivers because of
platform removal. So, we have a pleasant diffstat this time.
- first set of cleanups in the I2C core as preparation to increase
maximum length of SMBus transfers to 255 (as specified in the new
standard). Better documentation of struct i2c_msg and its flags stand
out here.
- the testunit can now respond to SMBus block process calls which is
the testcase when implementing the above new maximum length.
* 'i2c/for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (62 commits)
i2c: remove redundant error print in stm32f7_i2c_probe
i2c: testunit: add support for block process calls
i2c: busses: Replace spin_lock_irqsave with spin_lock in hard IRQ
dt-bindings: eeprom: at24: Document ROHM BR24G01
i2c: i801: Add support for Intel Alder Lake PCH-P
i2c: mv64xxx: Fix check for missing clock after adding RPM
i2c: mux: mlxcpld: Add callback to notify mux creation completion
i2c: mux: mlxcpld: Extend supported mux number
i2c: mux: mlxcpld: Extend driver to support word address space devices
i2c: mux: mlxcpld: Get rid of adapter numbers enforcement
i2c: mux: mlxcpld: Prepare mux selection infrastructure for two-byte support
i2c: mux: mlxcpld: Convert driver to platform driver
i2c: imx: Synthesize end of transaction events without idle interrupts
i2c: i2c-qcom-geni: Add shutdown callback for i2c
i2c: mv64xxx: Add runtime PM support
i2c: amd-mp2: Remove unused macro
i2c: amd-mp2: convert to PCI logging functions
i2c: mux: mlxcpld: Move header file out of x86 realm
platform/x86: mlxcpld: Update module license
i2c: mux: mlxcpld: Update module license
...
A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
* ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
* HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
* ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions and
fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
* Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support
-----BEGIN PGP SIGNATURE-----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=QgvS
-----END PGP SIGNATURE-----
Merge tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions
and fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support"
* tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (322 commits)
ALSA: hda: intel-dsp-config: add Alder Lake support
ASoC: soc-pcm: fix hw param limits calculation for multi-DAI
ASoC: Intel: bytcr_rt5640: Add quirk for the Acer One S1002 tablet
ASoC: Intel: bytcr_rt5651: Add quirk for the Jumper EZpad 7 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Voyo Winpad A15 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Estar Beauty HD MID 7316R tablet
ASoC: soc-pcm: fix hwparams min/max init for dpcm
ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup
ALSA: usb-audio: Add implicit fb quirk for BOSS GP-10
ALSA: hda: Add another CometLake-H PCI ID
ASoC: soc-pcm: add soc_pcm_hw_update_format()
ASoC: soc-pcm: add soc_pcm_hw_update_chan()
ASoC: soc-pcm: add soc_pcm_hw_update_rate()
ASoC: wm_adsp: Remove unused control callback structure
ASoC: SOF: relax ABI checks and avoid unnecessary warnings
ASoC: codecs: lpass-tx-macro: add dapm widgets and route
ASoC: codecs: lpass-tx-macro: add support for lpass tx macro
ASoC: qcom: dt-bindings: add bindings for lpass tx macro codec
ASoC: codecs: lpass-rx-macro: add iir widgets
ASoC: codecs: lpass-rx-macro: add dapm widgets and route
...
There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use [1], and
received confirmation about six ARM platforms and the TI C6x architecture
that have all reached the end of their life upstream, with no known
users remaining:
- efm32 -- added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell -- added in 2011, abandoned after 2012 acquisition
- prima2 -- added in 20111, no notable changes since 2015
- tango -- added in 2015, sporadic changes until 2017, but abandoned
- u300 -- added in 2009, no notable changes since 2013
- zx --added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x -- added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users
that plan to contribute them in the future, in other cases the code
is complete and works reliably.
[1] https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=pf3b
-----END PGP SIGNATURE-----
Merge tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform removals from Arnd Bergmann:
"There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use, and
received confirmation about six ARM platforms and the TI C6x
architecture that have all reached the end of their life upstream,
with no known users remaining:
- efm32 - added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell - added in 2011, abandoned after 2012 acquisition
- prima2 - added in 20111, no notable changes since 2015
- tango - added in 2015, sporadic changes until 2017, but abandoned
- u300 - added in 2009, no notable changes since 2013
- zx - added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x - added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users that
plan to contribute them in the future, in other cases the code is
complete and works reliably"
Link: https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
* tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: remove u300 platform
ARM: remove tango platform
ARM: remove zte zx platform
ARM: remove sirf prima2/atlas platforms
c6x: remove architecture
MAINTAINERS: Remove deleted platform efm32
ARM: drop efm32 platform
ARM: Remove PicoXcell platform support
ARM: dts: Remove PicoXcell platforms
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAtZ7cACgkQJNaLcl1U
h9DD5Af/eeERQ2uVOqtw0If+XL1xRYe6RewgDoNcO/l/5WxBLrBH6NbEf0OwNJeg
vzZAkUBtxmx6XiW2M/h+4ucW1OPcg5IzxIWTHfGDMlKIxzb0jgWugRnJ7sdTnOs3
c+QHnvuOT7QzZBviAIkc5uZ5thAImYF8zDyKoGF5llztmnBYymtgpnvnRNZGM0ou
76oUzSvkCFI2b0Yf6bpGok2nBVlOu82HSHOUKjXVWk+LAeiivlYGOEZpdIKEe3S8
u6atQJ29XRr52Yuc2z4xnFQTW1cIDlwj2Fk5x/z8hX+5nRhNSGuIv1l5m7TfBj3e
mCO9cltKZxly0NXysgekn95JHwwwkA==
=MJSb
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.12' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.12
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
Coccinelle reports a redundant error print in stm32f7_i2c_probe.
As 'platform_get_irq' already prints the error message, error
print here is redundant and can be removed.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There is no need to do irqsave and irqrestore in context of hard IRQ.
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add PCI ID of SMBus controller on Intel Alder Lake PCH-P.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In commit e5c02cf541 ("i2c: mv64xxx: Add runtime PM support"), error
pointers to optional clocks were replaced by NULL to simplify the resume
callback implementation. However, that commit missed that the IS_ERR
check in mv64xxx_of_config should be replaced with a NULL check. As a
result, the check always passes, even for an invalid device tree.
Fixes: e5c02cf541 ("i2c: mv64xxx: Add runtime PM support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Only the Layerscape SoCs have interrupts on bus idle, which facilitate
sending events which complete slave bus transactions.
Add support for synthesizing missing events. If we see a master request,
or a newly addressed slave request, if the last event sent to the backend
was I2C_SLAVE_READ_REQUESTED, send the backend a I2C_SLAVE_READ_PROCESSED
followed by I2C_SLAVE_STOP. For all other events, send an I2C_SLAVE_STOP.
Signed-off-by: Kevin Paul Herbert <kph@platinasystems.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the hardware is still accessing memory after SMMU translation
is disabled (as part of smmu shutdown callback), then the
IOVAs (I/O virtual address) which it was using will go on the bus
as the physical addresses which will result in unknown crashes
like NoC/interconnect errors.
So, implement shutdown callback to i2c driver to stop on-going transfer
and unmap DMA mappings during system "reboot" or "shutdown".
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To save power, gate the clock when the bus is inactive, during system
sleep, and during shutdown. On some platforms, specifically Allwinner
A13/A20, gating the clock implicitly resets the module as well. Since
the module already needs to be reset after some suspend/resume cycles,
it is simple enough to reset it during every runtime suspend/resume.
Because the bus may be used by wakeup source IRQ threads, it needs to
be functional as soon as IRQs are enabled. Thus, its system PM hooks
need to run in the noirq phase.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use pci_{info,warn,err,dbg} functions of the kernel's PCI API.
Remove unnecessary ndev_pdev(), ndev_name() and ndev_dev() macros.
While at it, remove useless __func__ from logging.
Signed-off-by: Richard Neumann <mail@richard-neumann.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some i2c device driver indirectly uses I2C driver when it is now
being suspended. The i2c devices driver is suspended during the
NOIRQ phase and this cannot be changed due to other dependencies.
Therefore, we also need to move the suspend handling for the I2C
controller driver to the NOIRQ phase as well.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch to use threaded interrupt context in order to avoid checking of
"are we in interrupt?" for the code that may sleep in the IRQ handler.
I2C doesn't require a very low interrupt-handling latency, hence this
change doesn't introduce any noticeable effects.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver core ignores the return value of the remove callback, so
don't give isa drivers the chance to provide a value.
Adapt all isa_drivers with a remove callbacks accordingly; they all
return 0 unconditionally anyhow.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/net/can/sja1000/tscan1.c
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for drivers/i2c/
Reviewed-by: Takashi Iway <tiwai@suse.de> # for sound/
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for drivers/media/
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210122092449.426097-4-uwe@kleine-koenig.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The I2C_SPRD uses Common Clock Framework thus it cannot be built on
platforms without it (e.g. compile test on MIPS with LANTIQ):
/usr/bin/mips-linux-gnu-ld: drivers/i2c/busses/i2c-sprd.o: in function `sprd_i2c_probe':
i2c-sprd.c:(.text.sprd_i2c_probe+0x254): undefined reference to `clk_set_parent'
Fixes: 4a2d5f663d ("i2c: Enable compile testing for more drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver implements I2C_M_RECV_LEN, so it can advertise the SMBus
transfers needing it. This also enables client devices to check for the
RECV_LEN capability.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver implements I2C_M_RECV_LEN, so it can advertise the SMBus
transfers needing it. This also enables client devices to check for the
RECV_LEN capability.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The smp8758 (tango4) SoC was the last generation of set-top-box chips
to come out of Sigma Designs, and support was added by Marc Gonzalez
and Måns Rullgård between 2015 and 2017, before the company went out of
business and the products were abandoned.
The chip is used in some set-top-boxes such as the Popcorn Hour A-500,
which could have seen some adoption by hobbyists. This has not happened
in the past four years, and support for the more widely used MIPS based
SoCs was never merged at all.
Thanks to Marc and Måns for maintaining for the past years even after the
death of the platform.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/lkml/2d643ebc-09af-a809-eb3f-2aec8ecee501@free.fr/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. No reason to add one to it.
Fixes: 886f6f8337 ("i2c: octeon: Support I2C_M_RECV_LEN")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
VI I2C controller has known hardware bug where immediate multiple
writes to TX_FIFO register gets stuck.
Recommended software work around is to read I2C register after
each write to TX_FIFO register to flush out the data.
This patch implements this work around for VI I2C controller.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Support for this machine was just removed, so drop the now unused i2c
bus driver, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Upon a communication error, the interrupt handler can call
tegra_i2c_disable_packet_mode. This causes a sleeping poll to happen
unless the current transaction was marked atomic. Fix this by
making the poll happen atomically if we are in an IRQ.
This matches the behavior prior to the patch mentioned
in the Fixes tag.
Fixes: ede2299f71 ("i2c: tegra: Support atomic transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for I2C bus frequency setting according to the specific
system capability. This capability is obtained from CPLD frequency
setting register, which could be provided through the platform data.
If such register is provided, it specifies minimal I2C bus frequency
to be used for the devices attached to the I2C bus. Supported
freqeuncies are 100KHz, 400KHz, 1MHz, while 100KHz is the default.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove dev_err() messages after platform_get_irq*() failures.
drivers/i2c/busses/i2c-hix5hd2.c:417:2-9: line 417 is redundant
because platform_get_irq() already prints an error
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Let MODULE_LICENCE match the SPDX header which is correctly based on the
previous textual description.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add code to handle IS_S_RX_FIFO_FULL_SHIFT interrupt to support
master write request with >= 64 bytes.
Iproc has a slave rx fifo size of 64 bytes.
Rx fifo full interrupt (IS_S_RX_FIFO_FULL_SHIFT) will be generated
when RX fifo becomes full. This can happen if master issues write
request of more than 64 bytes.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle single or multi byte master read request with or without
repeated start.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Update slave isr mask (ISR_MASK_SLAVE) to include remaining
two slave interrupts.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle only slave interrupts which are enabled.
The IS_OFFSET register contains the interrupt status bits which will be
set regardless of the enabling of the corresponding interrupt condition.
One must therefore look at both IS_OFFSET and IE_OFFSET to determine
whether an interrupt condition is set and enabled.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle Master aborted error by flushing tx and rx fifo
and reinitializing the hw.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
V3U creates spurious interrupts which we need to handle. This costs time
until BUS_PHASE_DATA can be activated which is problematic for Gen2 SoCs
and earlier. Because of this we introduce two interrupt handlers here
which will call a generic main irq function once the timing critical
stuff is done.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ensure this irq runs as fast as possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
'flags' and 'io' are needed first, so they should be at the beginning of
the private struct.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To avoid the HW race condition on R-Car Gen2 and earlier, we need to
write to ICMCR as soon as possible in the interrupt handler. We can
improve this by writing a static value instead of masking out bits.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.
Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_device_unregister() is NULL-aware and thus doesn't required a
duplication check in i801_del_mux(). Besides that it's also error pointer
aware, and we may drop unneeded assignment in i801_add_mux() followed by
conversion to PTR_ERR_OR_ZERO() for the returned value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since gpiod_remove_lookup_table() is NULL-aware, no need to have this check
in the caller. Drop duplicate NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Decrease polling time 'MLXCPLD_I2C_POLL_TIME' from 2000 usec to 400
usec. It greatly improves performance of I2C transactions.
Reliability of setting polling time to 400 usec has been thoroughly
validated across all the supported systems.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it requirs special
operation timing to reset i2c manually, otherwise the interrupt
will not be triggered, i2c transmission will be timeout.
Fixes: 8426fe70cfa4("i2c: mediatek: Add apdma sync in i2c driver")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
gpiod_add_lookup_table() expects the gpiod_lookup_table->table passed to
it to be terminated with a zero-ed out entry.
So we need to allocate one more entry then we will use.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the i2c device SCL bus being pulled up due to some exception before
message transfer done, the system cannot receive the completing interrupt
signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT
jiffies eclipse, that would make the system seemed hang up. To avoid that
happen, this patch adds a specific timeout for message transfer.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
[wsa: changed errno to ETIMEDOUT]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
* pm-sleep:
PM: sleep: Add dev_wakeup_path() helper
PM / suspend: fix kernel-doc markup
PM: sleep: Print driver flags for all devices during suspend/resume
* pm-acpi:
PM: ACPI: Refresh wakeup device power configuration every time
PM: ACPI: PCI: Drop acpi_pm_set_bridge_wakeup()
PM: ACPI: reboot: Use S5 for reboot
* pm-domains:
PM: domains: create debugfs nodes when adding power domains
PM: domains: replace -ENOTSUPP with -EOPNOTSUPP
* powercap:
powercap: Adjust printing the constraint name with new line
powercap: RAPL: Add AMD Fam19h RAPL support
powercap: Add AMD Fam17h RAPL support
powercap/intel_rapl_msr: Convert rapl_msr_priv into pointer
x86/msr-index: sort AMD RAPL MSRs by address
For the sake of consistency add leading 0 to first register offsets
to make them all of the same width.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently header file uses partially BIT() and GENMASK() macros.
Switch it to use those macros in all cases where it's applicable
for the sake of consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Starting with
commit 75820314de ("i2c: core: add generic I2C GPIO recovery")
GPIO bus recovery is supported by the I2C core, so we can remove the
driver implementation and use that one instead.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a driver tries to send an I2C message while the adapter is
suspended, this typically fails with:
i2c-sh_mobile e60b0000.i2c: Transfer request timed out
Avoid accessing the adapter while it is suspended by marking it
suspended during suspend. This allows the I2C core to catch this, and
print a warning:
WARNING: CPU: 1 PID: 13 at drivers/i2c/i2c-core.h:54
__i2c_transfer+0x4a4/0x4e4
i2c i2c-6: Transfer while suspended
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add S500 variant to the list of devices supported by the Actions Semi
Owl I2C driver.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_ioremap and ioremap may return NULL which cannot be checked
by IS_ERR.
Signed-off-by: Wang Xiaojun <wangxiaojun11@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If this is not enabled, the interfaces used in this driver do not work:
drivers/i2c/busses/i2c-mlxbf.c:1888:3: error: implicit declaration of function 'i2c_slave_event' [-Werror,-Wimplicit-function-declaration]
i2c_slave_event(slave, I2C_SLAVE_WRITE_REQUESTED, &value);
^
drivers/i2c/busses/i2c-mlxbf.c:1888:26: error: use of undeclared identifier 'I2C_SLAVE_WRITE_REQUESTED'
i2c_slave_event(slave, I2C_SLAVE_WRITE_REQUESTED, &value);
^
drivers/i2c/busses/i2c-mlxbf.c:1890:32: error: use of undeclared identifier 'I2C_SLAVE_WRITE_RECEIVED'
ret = i2c_slave_event(slave, I2C_SLAVE_WRITE_RECEIVED,
^
drivers/i2c/busses/i2c-mlxbf.c:1892:26: error: use of undeclared identifier 'I2C_SLAVE_STOP'
i2c_slave_event(slave, I2C_SLAVE_STOP, &value);
^
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Expand the driver to support I2C_SMBUS_BLOCK_PROC_CALL since
HW supports it already.
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mario Alejandro Posso Escobar <mario.posso.escobar@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() on an error.
In case of i2c ocores this leads to a false-positive error being logged:
[ 4.173989] 007: ocores-i2c ocores-i2c: IRQ index 0 not found
i2c ocores already handles the case when the IRQ cannot be found and
therefore there is no benefit in having this error message being logged.
This commit switches to platform_get_irq_optional(), which does not log
in case the IRQ cannot be found.
Signed-off-by: Stefan Lässer <stefan.laesser@omicronenergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A combination of recent bug fixes by Doug Anderson and the proper
definition of iommu streams means that this hack is no longer needed.
Let's clean up the code by reverting '127068abe85b ("i2c: qcom-geni:
Disable DMA processing on the Lenovo Yoga C630")'.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Caleb Connolly <caleb@connolly.tech>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c-mxs driver only runs on DT-platform and there is no
need to use the platform_device_id structure to pass the driver
data.
Get rid of it to make the code simpler.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
io_base and io_size are assigned to only in .probe() and otherwise unused.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
After the commit c5eb119007 ("PCI / PM: Allow runtime PM without callback
functions") we no more need empty stubs for runtime-pm to work.
The driver has no device specific task(s) for .suspend() . The stub was
placed just for runtime-pm, which can be dropped now.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This adds i2c bus recovery to the mv64xxx driver.
Implement bus recovery to recover from SCL/SDA stuck low.
This uses the generic recovery function, setting the clock/data lines as
GPIO pins, and sending 9 clocks to try and recover the bus.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
[wsa: added some curly braces]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
During cci_isr() errors read from register fields belonging to
i2c master1 are currently assigned to the status field belonging to
i2c master0. This patch corrects this error, and always assigns
master1 errors to the status field of master1.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Suggested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add dev_wakeup_path() helper to avoid to spread
dev->power.wakeup_path test in drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes we would get the following flow when doing an i2cset:
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
I2C_SLAVE_WRITE_RECEIVED
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
I2C_SLAVE_WRITE_REQUESTED
I2C_SLAVE_WRITE_RECEIVED
Documentation/i2c/slave-interface.rst says that I2C_SLAVE_WRITE_REQUESTED,
which is mandatory, should be sent while the data did not arrive yet. It
means in a write-request I2C_SLAVE_WRITE_REQUESTED should be reported
before any I2C_SLAVE_WRITE_RECEIVED.
By the way, I2C_SLAVE_STOP didn't be reported in the above case because
DW_IC_INTR_STAT was not 0x200.
dev->status can be used to record the current state, especially Designware
I2C controller has no interrupts to identify a write-request. This patch
makes not only I2C_SLAVE_WRITE_REQUESTED been reported first when
IC_INTR_RX_FULL is rising and dev->status isn't STATUS_WRITE_IN_PROGRESS
but also I2C_SLAVE_STOP been reported when a STOP condition is received.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If some bits were cleared by i2c_dw_read_clear_intrbits_slave() in
i2c_dw_isr_slave() and not handled immediately, those cleared bits would
not be shown again by later i2c_dw_read_clear_intrbits_slave(). They
therefore were forgotten to be handled.
i2c_dw_read_clear_intrbits_slave() should be called once in an ISR and take
its returned state for all later handlings.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The Mellanox BlueField I2C controller is only present on Mellanox
BlueField SoCs. Hence add a dependency on MELLANOX_PLATFORM, to prevent
asking the user about this driver when configuring a kernel without
Mellanox platform support.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Correct the email addresses of the author and the maintainer
of the Mellanox BlueField I2C driver.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The reference clock frequency remains the same across Bluefield
products. Thus, update the frequency and rename the macro.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Few wrapper functions are useless and can be inlined. So
delete mlxbf_i2c_read() and mlxbf_i2c_write() and replace
them with readl() and writel(), respectively. Also delete
mlxbf_i2c_read_data() and mlxbf_i2c_write() and replace
them with ioread32be() and iowrite32be(), respectively.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The build fails with "implicit declaration of function
'acpi_device_uid'" error. Thus, protect ACPI function calls
from being called when CONFIG_ACPI is disabled.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implements atomic transfers to fix reboot/shutdown on r8a7790 Lager and
similar boards.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: some whitespace fixing]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_irq never returns 0. Don't check for this. Make it clear that
the error path always returns a negative error code.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If platform_get_irq returns an error, relay this error to the caller of
the probe function. Don't change all errors to -EINVAL. This breaks the
case where platform_get_irq returns -EPROBE_DEFER.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_irq already prints an error message if the requested irq
was not found. Don't print another message in the driver.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c driver default do dma reset after i2c reset, but sometimes
i2c reset will trigger dma tx2rx, then apdma write data to dram
which has been i2c_put_dma_safe_msg_buf(kfree). Move dma reset
before i2c reset in mtk_i2c_init_hw to fix it.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The FU540-C000 has a broken IRQ and support was added earlier
so that it will operate in polling mode, but seems to work only
in case interrupts property is missing from the i2c0 dt-node.
This should not be the case and the driver should handle polling
mode with the interrupt property present in i2c0 node of the
device tree.
So check if it's the FU540-C000 soc and enable polling mode master
xfers, as the IRQ for this chip is broken.
Fixes commit c45d4ba867 ("i2c: ocores: add polling mode workaround
for Sifive FU540-C000 SoC")
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Speed up the boot process by using the asynchronous probing feature
supported by the recent kernels.
For SBCs based on the Actions Semi S500 SoC, the overall boot time is
expected to be reduced by 200-300 ms.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Atomic transfers are required to properly power off a machine through
an I2C controlled PMIC, such as the Actions Semi ATC260x series.
System shutdown may happen with interrupts being disabled and, as a
consequence, the kernel may hang if the driver does not support atomic
transfers.
This functionality is essentially implemented by polling the FIFO
Status register until either Command Execute Completed or NACK Error
bits are set.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[wsa: rebased to current tree]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit dc6df6e90d ("i2c: at91: remove legacy DMA support") removed legcy
DMA support from the driver. Remove the last use of the definitions from
linux/platform_data/dma-atmel.h and stop including this header.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
[wsa: fixed typo in subject]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit 02b9aec592.
As talked about in the patch ("soc: qcom: geni: More properly switch
to DMA mode"), swapping the order of geni_se_setup_m_cmd() and
geni_se_xx_dma_prep() can sometimes cause corrupted transfers. Thus
we traded one problem for another. Now that we've debugged the
problem further and fixed the geni helper functions to more disable
FIFO interrupts when we move to DMA mode we can revert it and end up
with (hopefully) zero problems!
To be explicit, the patch ("soc: qcom: geni: More properly switch
to DMA mode") is a prerequisite for this one.
Fixes: 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.2.I7b22281453b8a18ab16ef2bfd4c641fb1cc6a92c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull i2c updates from Wolfram Sang:
- if a host can be a client, too, the I2C core can now use it to
emulate SMBus HostNotify support (STM32 and R-Car added this so far)
- also for client mode, a testunit has been added. It can create rare
situations on the bus, so host controllers can be tested
- a binding has been added to mark the bus as "single-master". This
allows for better timeout detections
- new driver for Mellanox Bluefield
- massive refactoring of the Tegra driver
- EEPROMs recognized by the at24 driver can now have custom names
- rest is driver updates
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (80 commits)
Documentation: i2c: add testunit docs to index
i2c: tegra: Improve driver module description
i2c: tegra: Clean up whitespaces, newlines and indentation
i2c: tegra: Clean up and improve comments
i2c: tegra: Clean up printk messages
i2c: tegra: Clean up variable names
i2c: tegra: Improve formatting of variables
i2c: tegra: Check errors for both positive and negative values
i2c: tegra: Factor out hardware initialization into separate function
i2c: tegra: Factor out register polling into separate function
i2c: tegra: Factor out packet header setup from tegra_i2c_xfer_msg()
i2c: tegra: Factor out error recovery from tegra_i2c_xfer_msg()
i2c: tegra: Rename wait/poll functions
i2c: tegra: Remove "dma" variable from tegra_i2c_xfer_msg()
i2c: tegra: Remove redundant check in tegra_i2c_issue_bus_clear()
i2c: tegra: Remove likely/unlikely from the code
i2c: tegra: Remove outdated barrier()
i2c: tegra: Clean up variable types
i2c: tegra: Reorder location of functions in the code
i2c: tegra: Clean up probe function
...
When the NACK and BUS error bits are set by the hardware, the driver is
responsible for clearing them by writing "1" into the corresponding
status registers.
Hence perform the necessary operations in owl_i2c_interrupt().
Fixes: d211e62af4 ("i2c: Add Actions Semiconductor Owl family S900 I2C driver")
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit fa4d305568. An updated
version was sent. So, revert this version and give the new version more
time for testing.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Apparently, 15 cycles of the peripheral clock are used by the controller
for sampling and filtering. Because this was not known before, the rate
calculation is slightly off.
Clean up and fix the calculation taking this filtering delay into account.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
SCL rate appears to be different than what is expected. For example,
We get 164kHz on i2c3 of the vim3 when 400kHz is expected. This is
partially due to the peripheral clock being disabled when the clock is
set.
Let's keep the peripheral clock on after probe to fix the problem. This
does not affect the SCL output which is still gated when i2c is idle.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When the slave address is written in do_start(), SLAVE_ADDR is written
completely. This may overwrite some setting related to the clock rate
or signal filtering.
Fix this by writing only the bits related to slave address. To avoid
causing unexpected changed, explicitly disable filtering or high/low
clock mode which may have been left over by the bootloader.
Fixes: 30021e3707 ("i2c: add support for Amlogic Meson I2C controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use proper spelling of "NVIDIA" and don't designate driver as Tegra2-only
since newer SoC generations are supported as well.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some places in the code are missing newlines or have unnecessary
whitespaces and newlines. This creates inconsistency of the code and
hurts readability. This patch removes the unnecessary and adds necessary
whitespaces / newlines, clears indentation of the code.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make all comments to be consistent in regards to capitalization and
punctuation, correct spelling and grammar errors, improve wording.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch unifies style of all messages in the driver by starting them
with a lowercase letter and using consistent capitalization and wording
for all messages.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rename "ret" variables to "err" in order to make code a bit more
expressive, emphasizing that the returned value is an error code.
Same vice versa, where appropriate.
Rename variable "reg" to "val" in order to better reflect the actual
usage of the variable in the code and to make naming consistent with
the rest of the code.
Use briefer names for a few members of the tegra_i2c_dev structure in
order to improve readability of the code.
All dev/&pdev->dev are replaced with i2c_dev->dev in order to have uniform
code style across the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reorder definition of variables in the code to have them sorted by length
and grouped logically, also replace "unsigned long" with "u32". Do this in
order to make code easier to read.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver's code is inconsistent in regards to the error values checking.
The correct way should be to check both positive and negative values.
This patch cleans up the error-checks in the code. Note that the
pm_runtime_get_sync() could return positive value on success, hence only
relevant parts of the code are changed by this patch.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Factor out hardware initialization into a separate function from the probe
function. The only place where runtime PM needs to be resumed during probe
is the place of hardware initialization, hence it makes sense to factor
out it in order to have a bit cleaner error handling in tegra_i2c_probe().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Factor out register polling into a separate function in order to remove
boilerplate code and make code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The code related to packet header setting up is a bit messy and makes
tegra_i2c_xfer_msg() more difficult to read than it could be. Let's
factor the packet header setup from tegra_i2c_xfer_msg() into separate
function in order to make code easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Factor out error recovery code from tegra_i2c_xfer_msg() in order to
make this function easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Drop '_timeout' postfix from the wait/poll completion function names in
order to make the names shorter, making code cleaner a tad.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "dma" variable of tegra_i2c_xfer_msg() function doesn't bring much in
regards to readability and generation of the code.
Besides readability, it's also not very nice that the is_curr_dma_xfer
is initialized in tegra_i2c_xfer_msg() and then could be overridden by
tegra_i2c_config_fifo_trig(). In a result, the "dma" variable creates
slight confusion since it's not instantly obvious why it's set after
tegra_i2c_config_fifo_trig().
Hence should be better to have the variable removed. This makes code
more consistent.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The tegra_i2c_wait_for_config_load() checks for 'has_config_load_reg' by
itself, hence there is no need to duplicate the check.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The likely/unlikely annotations should be used only in a hot paths of
performance-critical code. The I2C driver doesn't have such paths, and
thus, there is no justification for usage of likely/unlikely annotations
in the code. Hence remove them.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The barrier() was intended to reduce possibility of racing with the
interrupt handler, but driver's code evolved significantly and today's
driver enables interrupt only when it waits for completion notification.
Hence barrier() has no good use anymore, let's remove it.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Don't use signed types for unsigned values and use consistent types
for sibling variables.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reorder location of functions in the code in order to have definition
of functions closer to the place of the invocation. This change makes
easier to navigate around the code and removes the need to have a
prototype for tegra_i2c_init().
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver's probe function code is a bit difficult to read. This patch
reorders code of the probe function, forming groups of code that are easy
to work with. The probe tear-down order now matches the driver-removal
order.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move out code related to device-tree parsing from the probe function into
tegra_i2c_parse_dt() in order to make code more consistent.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use clk-bulk helpers and factor out clocks initialization into separate
function in order to make code cleaner.
The clocks initialization now performed after reset-control initialization
in order to avoid a noisy -PROBE_DEFER errors on T186+ from the clk-bulk
helper which doesn't silence this error code. Hence reset_control_get()
now may return -EPROBE_DEFER on newer Tegra SoCs because they use BPMP
driver that provides reset controls and BPMP doesn't come up early during
boot. Previously rst was protected by the clocks retrieval and now this
patch makes dev_err_probe() to be used for the rst error handling.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use common helper for retrieval of the interrupt number in order to make
code cleaner. Note that platform_get_irq() prints error message by itself.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Driver now uses devm_platform_get_and_ioremap_resource() which replaces
the typical boilerplate code and makes code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use a single reset_control_reset() instead of assert/deasset couple in
order to make code cleaner a tad. Note that the reset_control_reset()
uses 1 microsecond delay instead of 2 that was used previously, but this
shouldn't matter because one microsecond is a default reset time for most
of Tegra peripherals and TRM doesn't mention anything special in regards
to I2C controller's reset propagation time.
In addition don't ignore potential error of the reset control by emitting
a noisy warning if it fails, which will indicate an existence of a severe
problem, while still allow machine to boot up.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The error message prints number of vIRQ, which isn't a useful information.
In practice devm_request_irq() never fails, hence let's remove the bogus
message in order to make code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The runtime PM is guaranteed to be always available on Tegra after commit
40b2bb1b13 ("ARM: tegra: enforce PM requirement"). Hence let's remove
all the RPM-availability checking and handling from the code.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "non_hs_mode" divisor value is fixed, thus there is no need to have
the variable i2c_dev.clk_divisor_non_hs_mode struct member. Let's remove
it and move the mode selection into tegra_i2c_init() where it can be
united with the timing selection.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It doesn't make sense to conditionalize the div-clk rate changes because
rate is fixed and it won't ever change once it's set at the driver's probe
time. All further changes are NO-OPs because CCF caches rate and skips
rate-change if rate is unchanged.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The tegra_i2c_issue_bus_clear() may fail and in this case BUS_CLR_DONE
stays unmasked. Hence let's mask it for consistency. This patch doesn't
fix any known problems.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Technically the tegra_i2c_flush_fifos() may fail and transfer should be
aborted in this case, but this shouldn't ever happen in practice unless
there is a bug somewhere in the driver. Let's add the error check just
for completeness.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The pm_runtime_get_sync() always bumps refcount regardless of whether it
succeeds or fails. Hence driver is responsible for restoring of the RPM
refcounting. This patch adds missing RPM puts which restore refcounting
in a case of pm_runtime_get_sync() error.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The tegra_i2c_flush_fifos() shouldn't sleep in atomic transfer and jiffies
are not updating if interrupts are disabled. Let's switch to use iopoll
API helpers for register-polling. The iopoll API provides helpers for both
atomic and non-atomic cases.
Note that this patch doesn't fix any known problem because normally FIFO
is flushed at the time of starting a new transfer.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make use of devm_platform_get_and_ioremap_resource() provided by
driver core platform instead of duplicated analogue. dev_err() is
removed because it has been done in devm_ioremap_resource().
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add PCI ID of SMBus controller on Intel Alder Lake PCH-S
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Due to a HW issue, in some scenarios the LAST bit might remain set.
This will cause an unexpected NACK after reading 16 bytes on the next
read.
Example: if user tries to read from a missing device, get a NACK,
then if the next command is a long read ( > 16 bytes),
the master will stop reading after 16 bytes.
To solve this, if a command fails, check if LAST bit is still
set. If it does, reset the module.
Fixes: 56a1485b10 (i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver)
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If interrupt comes late, during probe error path or device remove (could
be triggered with CONFIG_DEBUG_SHIRQ), the interrupt handler
i2c_imx_isr() will access registers with the clock being disabled. This
leads to external abort on non-linefetch on Toradex Colibri VF50 module
(with Vybrid VF5xx):
Unhandled fault: external abort on non-linefetch (0x1008) at 0x8882d003
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.7.0 #607
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
(i2c_imx_isr) from [<8017009c>] (free_irq+0x25c/0x3b0)
(free_irq) from [<805844ec>] (release_nodes+0x178/0x284)
(release_nodes) from [<80580030>] (really_probe+0x10c/0x348)
(really_probe) from [<80580380>] (driver_probe_device+0x60/0x170)
(driver_probe_device) from [<80580630>] (device_driver_attach+0x58/0x60)
(device_driver_attach) from [<805806bc>] (__driver_attach+0x84/0xc0)
(__driver_attach) from [<8057e228>] (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from [<8057f3ec>] (bus_add_driver+0x144/0x1ec)
(bus_add_driver) from [<80581320>] (driver_register+0x78/0x110)
(driver_register) from [<8010213c>] (do_one_initcall+0xa8/0x2f4)
(do_one_initcall) from [<80c0100c>] (kernel_init_freeable+0x178/0x1dc)
(kernel_init_freeable) from [<80807048>] (kernel_init+0x8/0x110)
(kernel_init) from [<80100114>] (ret_from_fork+0x14/0x20)
Additionally, the i2c_imx_isr() could wake up the wait queue
(imx_i2c_struct->queue) before its initialization happens.
The resource-managed framework should not be used for interrupt handling,
because the resource will be released too late - after disabling clocks.
The interrupt handler is not prepared for such case.
Fixes: 1c4b6c3bcf ("i2c: imx: implement bus recovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add BlueField I2C driver to offer master and slave support for
Mellanox BlueField SoCs. The driver implements an SMBus adapter
and interfaces to multiple busses that can be probed using both
ACPI and Device Tree infrastructures.
The driver supports several SMBus operations to transfer data
back and forth from/to various I2C devices. It is mainly intended
to be consumed by userspace tools and utilities, such as i2c-tools
and decode-dimms to collect memory module information.
On the other hand, the driver has a slave function to support,
among others, an IPMB interface that requires both master and
slave functions to handle transfers between the BlueField SoC
and a board management controllers (e.g., BMC).
Signed-off-by: Khalil Blaiech <kblaiech@mellanox.com>
Reviewed-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
the i2c_ram structure is missing the sdmatmp field mentionned in
datasheet for MPC8272 at paragraph 36.5. With this field missing, the
hardware would write past the allocated memory done through
cpm_muram_alloc for the i2c_ram structure and land in memory allocated
for the buffers descriptors corrupting the cbd_bufaddr field. Since this
field is only set during setup(), the first i2c transaction would work
and the following would send data read from an arbitrary memory
location.
Fixes: 61045dbe9d ("i2c: Add support for I2C bus on Freescale CPM1/CPM2 controllers")
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This makes the driver code slightly easier to read.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add PCI ID for the Intel Emmitsburg PCH iSMT SMBus controller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Seth Heasley <seth.heasley@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Kernel doc validation script complains:
CHECK .../drivers/i2c/busses/i2c-ismt.c
.../i2c-ismt.c:182: warning: cannot understand function prototype: 'const struct pci_device_id ismt_ids[] = '
.../i2c-ismt.c:202: warning: Function parameter or member 'dev' not described in '__ismt_desc_dump'
.../i2c-ismt.c:202: warning: Function parameter or member 'desc' not described in '__ismt_desc_dump'
.../i2c-ismt.c:649: warning: cannot understand function prototype: 'const struct i2c_algorithm smbus_algorithm = '
Fix corresponding descriptions to make reader and kernel doc validator happy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Seth Heasley <seth.heasley@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
CONFIG_OF is selected by CONFIG_MACH_INGENIC, therefore we don't need to
handle the case where Device Tree is not supported.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C controller in the JZ4770 SoC seems to work the exact same as in
the JZ4780 SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
clang static analyzer reports this problem
i2c-amd-mp2-plat.c:174:9: warning: Branch condition evaluates
to a garbage value
return err ? err : num;
^~~
err is not initialized, it depends on the being set in the
transfer loop which will not happen if num is 0. Surveying
other master_xfer() implementations show all handle a 0 num.
Because returning 0 is expected, initialize err to 0.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Elie Morisse <syniurge@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DMA usage is optional for the I2C driver. check for the -ENODEV
error in order to avoid displaying an error when no DMA
has been requested.
Cleaning up the error messages during probe, remove the additional
-EPROBE_DEFER within probe function since additional error message
doesn't give much more information than what is already reported
within the stm32_i2c_dma_request function.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
By default, PCI drivers with runtime PM enabled will skip the calls
to suspend and resume on system PM. For this driver, we don't want
that, as we need to perform additional steps for system PM to work
properly on all systems. So instruct the PM core to not skip these
calls.
Fixes: a9c8088c79 ("i2c: i801: Don't restore config registers on runtime PM")
Reported-by: Volker Rümelin <volker.ruemelin@googlemail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The I2C core can now utilize a slave interface to handle SMBus
HostNotify events. Enable it in this driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver-specific usage of the DMA_CTRL_ACK flag was replaced with a
custom flag in commit ceeeb99cd8 ("dmaengine: mxs: rename custom flag"),
but i2c-mxs was not updated to use the new flag, completely breaking I2C
transactions using DMA.
Fixes: ceeeb99cd8 ("dmaengine: mxs: rename custom flag")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
LOOP_TIMEOUT was only used back then because we didn't want to introduce
another constant. The timeout value can easily be a magnitude shorter
because the typical range is 3us - 8us. Refactor the code to use the
poll_timeout helper, use a specific timeout value and get rid of the
ugly LOOP_TIMEOUT constant.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C doesn't define a timeout for bus busy, so an arbitrary value like
LOOP_TIMEOUT is not a good idea. Let's use the timeout value in struct
adapter which is meant for such cases and is user-configurable (via
IOCTL). To reduce the load, wait 10us instead of 1us which is good
enough for the slow frequencies used by I2C. Finally, use the
poll_timeout helper instead of open coding it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rely on the core functions to implement the host-notify
protocol via the a I2C slave device.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The master code needs to being sent when the speed is more than
I2C_MAX_FAST_MODE_PLUS_FREQ, not I2C_MAX_FAST_MODE_FREQ in the
latest I2C-bus specification and user manual.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The max frequency of mediatek i2c controller driver is
I2C_MAX_HIGH_SPEED_MODE_FREQ, not I2C_MAX_FAST_MODE_PLUS_FREQ.
Fix it.
Fixes: 90224e6468 ("i2c: drivers: Use generic definitions for bus frequencies")
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We don't actually need to derive the PCI device from the device
structure, as we already have a pointer to it in our private data
structure.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On suspend the original host configuration gets restored. The
resume routine has to undo this, otherwise the SMBus master
may be left in disabled state or in i2c mode.
[JD: Rebased on v5.8, moved the write into i801_setup_hstcfg.]
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: stable@vger.kernel.org
Mask the IRQ status to only the bits that the driver checks. This
prevents excessive driver warnings when operating in slave mode
when additional bits are set that the driver doesn't handle.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Value of /sys/devices/platform/lis3lv02d/position when
Horizontal: (36,-108,-1152)
Left elevated: (-432,-126,-1062)
Front elevated: (36,594,-936)
Upside down: (-126,-252,1098)
Signed-off-by: Jeffrey Lin <jeffrey@icurse.nl>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
timeout_usec value calculation was wrong, the calculated value
was in msec instead of usec.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Reviewed-by: Avi Fishman <avifishman70@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c fixes from Wolfram Sang:
"A core fix for ACPI matching and two driver bugfixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: iproc: Fix shifting 31 bits
i2c: rcar: in slave mode, clear NACK earlier
i2c: acpi: Remove dead code, i.e. i2c_acpi_match_device()
i2c: core: Don't fail PRP0001 enumeration when no ID table exist
The i2c-rcar driver utilizes the Generic Reset Controller kernel
feature, so select the RESET_CONTROLLER option when the I2C_RCAR
option is selected with a Gen3 SoC.
Fixes: 2b16fd6305 ("i2c: rcar: handle RXDMA HW behaviour on Gen3")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Lowe <andy_lowe@mentor.com>
[erosca: Add "if ARCH_RCAR_GEN3" per Wolfram's request]
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C master operating in multimaster mode can get stuck
indefinitely if I2C start is detected on bus, but no master
has a transaction going.
This is a weakness in I2C standard, which defines no way
to recover, since all masters are indefinitely disallowed
from interrupting the currently operating master. A start
condition can be created for example by an electromagnetic
discharge applied near physical I2C lines. Or a already
operating master could get reset immediately after sending
a start.
If it is known during device tree creation that only a single
I2C master will be present on the bus, this deadlock of the
I2C bus could be avoided in the driver by ignoring the
bus_is_busy register of the xiic, since bus can never be
reserved by any other master.
This patch adds this support for detecting single-master flag
in device tree and when provided, improves I2C reliability by
ignoring the therefore unnecessary xiic bus_is_busy register.
Error can be reproduced by pulling I2C SDA -line temporarily low
by shorting it to ground, while linux I2C master is operating on
it using the xiic driver. The application using the bus will
start receiving linux error code 16: "Device or resource busy"
indefinitely:
kernel: pca953x 0-0020: failed writing register
app: Error writing file, error: 16
With multi-master disabled device will instead receive error
code 5: "I/O error" while SDA is grounded, but recover normal
operation once short is removed.
kernel: pca953x 0-0020: failed reading register
app: Error reading file, error: 5
Signed-off-by: Jaakko Laine <ext-jaakko.laine@vaisala.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
xiic_i2c struct alignment causes the struct to
take more space in memory than strictly required.
Move state -member to end of struct to get less
padding.
Signed-off-by: Jaakko Laine <ext-jaakko.laine@vaisala.com>
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Alignment removed and replaced with 1 space only to
reduce need for future alignment changes affecting multiple
lines, when new variables are added.
Signed-off-by: Jaakko Laine <ext-jaakko.laine@vaisala.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The default value for a config option defaults to 'n' so it doesn't need
to be set here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
[jdelvare: found another one]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix undefined behaviour in the iProc I2C driver by using 'BIT' marcro.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
[wsa: in commit msg, don't say 'checkpatch' but name the issue]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
driver and the Designware i2c driver (changes from Akshu Agrawal and
Pu Wen).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl820JQSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxy2wP/jXaIw3YtMhDeu0V9qsODq4BuDEW4wV+
ZaKny6fz1AVekhdH/0BUh4GdgSJQMyuKpL3i0SPJamkykwQSxQnGo6X8g7NWwjQF
d0HPNW7QOJE1B9gyLKj7zI5RRVwXSAHJxO3651QH+0CUcNHggFRGEXYGCEukvJBz
CM5ZxMRaFOTvqHVu38cmL7LFNveO8dO1V4SKAQzsOpipW8//noxC/eaE86Rg2Zk/
1x3F5jBv07Cdt7JJOO44PEKyH6uNU7tkfkfGKeEiWxi+b+CiSpvJPMCgOS6eb/gS
mBTVMXvB5IuLcXvG3ftr2gVbl87bh27wUmcQyJuLNfj6tEsVwz3rvPd6aRpXmu1R
xnto4R8FPnIGb5XFKU1fbOgQwueliKAVt0mhfi8AYJUshpC3jtPtfJeH8dumPBp4
ZfBu8h7uk77mpunQ8B8VL/+Kj5f7kiQ5hRWRBxv2KPQMdljy1ufeQbWAgc+XY/EG
eSzo8qxdRs6PGWfXVDVZu3hCMJ+nSzY/GsBJ0z/p7+29HGczQZdYPMU0iWoM6DMS
dSq8/+4m1JReA3HGdgbgBVs3EH0V/zReCAR6bdAFvFuAAubm2mXQfliVzhdNVDQ2
7MVxuhU11p7CEwp5i+UZNvJ11KT2oyqHtboLkqNBHMm2fnRZBTUL05wLEP35adj9
WwK7n2XpSKc0
=D9q+
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Add new hardware support to the ACPI driver for AMD SoCs, the x86 clk
driver and the Designware i2c driver (changes from Akshu Agrawal and
Pu Wen)"
* tag 'acpi-5.9-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
clk: x86: Support RV architecture
ACPI: APD: Add a fmw property is_raven
clk: x86: Change name from ST to FCH
ACPI: APD: Change name from ST to FCH
i2c: designware: Add device HID for Hygon I2C controller
Pull i2c updates from Wolfram Sang:
- bus recovery can now be given a pinctrl handle and the I2C core will
do all the steps to switch to/from GPIO which can save quite some
boilerplate code from drivers
- "fallthrough" conversion
- driver updates, mostly ID additions
* 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (32 commits)
i2c: iproc: fix race between client unreg and isr
i2c: eg20t: use generic power management
i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume
i2c: mediatek: Fix i2c_spec_values description
i2c: mediatek: Add i2c compatible for MediaTek MT8192
dt-bindings: i2c: update bindings for MT8192 SoC
i2c: mediatek: Add access to more than 8GB dram in i2c driver
i2c: mediatek: Add apdma sync in i2c driver
i2c: i801: Add support for Intel Tiger Lake PCH-H
i2c: i801: Add support for Intel Emmitsburg PCH
i2c: bcm2835: Replace HTTP links with HTTPS ones
Documentation: i2c: dev: 'block process call' is supported
i2c: at91: Move to generic GPIO bus recovery
i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOs
i2c: core: add generic I2C GPIO recovery
dt-bindings: i2c: add generic properties for GPIO bus recovery
i2c: rcar: avoid race when unregistering slave
i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c
i2c: tegra: Fix runtime resume to re-init VI I2C
i2c: tegra: Fix the error path in tegra_i2c_runtime_resume
...
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver calls pci_enable_wake(...., false) in pch_i2c_suspend() as well
as pch_i2c_resume(). Either it should enable-wake the device in .suspend()
or should not invoke pci_enable_wake() at all.
Concluding that this driver doesn't support enable-wake and PCI core calls
pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from
.suspend() and .resume().
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The struct i2c_spec_values have it's members documented but is
missing the starting '@', which leads to warings like:
drivers/i2c/busses/i2c-mt65xx.c:267: warning: Function parameter or member 'min_low_ns' not described in 'i2c_spec_values'
We also delete min_high_ns member as it is not used in the code.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add device HID HYGO0010 to match the Hygon ACPI Vendor ID (HYGO) that
was registered in http://www.uefi.org/acpi_id_list, and the I2C
controller on Hygon paltform will use the HID.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add i2c compatible for MT8192. Compare to MT8183 i2c controller,
MT8192 support more then 8GB DMA mode.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Newer MTK chip support more than 8GB of dram. Replace support_33bits
with more general dma_max_support and remove mtk_i2c_set_4g_mode.
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it need to keep i2c and
apdma in sync manually.
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add SMBus PCI ID on Intel Tiger Lake PCH-H.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for SMBus controller on Intel Emmitsburg PCH. This is the
same IP as used in Cannon Lake and derivatives.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[wsa: shortened commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Make the Microchip at91 driver the first to use the generic GPIO bus
recovery support from the I2C core and discard the driver implementation.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAl8eiUATHHJwcHRAbGlu
dXguaWJtLmNvbQAKCRA5A4Ymyw79kWs8B/4wEWVJGTkjyrMX57/Ew8yRYAJE6JjA
kSONPjElVrPR1pRLYyjyde+zqumkJFhk+41De09J2byL29p7tK8ISNrTwJrIN7n/
dzT73CmuNEjI0rZJxPX+USKFph75FQVvAVOOWs+6fiBFxdUaIsBheVntH7/NsCTk
HFrIjIn5wXFVs5Nh+2cHydvEpOVoUWzjvs+uJIEpHCVCBz6gaYq2dxEmeTquKuz1
k7PZqCqVsyB9iWLqN65/Q+30N8znJwcUl8HAzs5nvPrXLjGxwuEjOxtYYhbdLAfP
OBiIF9J77sZxBlms0WNomDW3Rr5Vlt5nF9oUWpi3AmHNWIuX0GkM4i0C
=V+Kl
-----END PGP SIGNATURE-----
Merge tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux
Pull unicore32 removal from Mike Rapoport:
"Remove unicore32 support.
The unicore32 port do not seem maintained for a long time now, there
is no upstream toolchain that can create unicore32 binaries and all
the links to prebuilt toolchains for unicore32 are dead. Even
compilers that were available are not supported by the kernel anymore.
Guenter Roeck says:
"I have stopped building unicore32 images since v4.19 since there is
no available compiler that is still supported by the kernel. I am
surprised that support for it has not been removed from the kernel"
However, it's worth pointing out two things:
- Guan Xuetao is still listed as maintainer and asked for the port to
be kept around the last time Arnd suggested removing it two years
ago. He promised that there would be compiler sources (presumably
llvm), but has not made those available since.
- https://github.com/gxt has patches to linux-4.9 and qemu-2.7, both
released in 2016, with patches dated early 2019. These patches
mainly restore a syscall ABI that was never part of mainline Linux
but apparently used in production. qemu-2.8 removed support for
that ABI and newer kernels (4.19+) can no longer be built with the
old toolchain, so apparently there will not be any future updates
to that git tree"
* tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux:
MAINTAINERS: remove "PKUNITY SOC DRIVERS" entry
rtc: remove fb-puv3 driver
video: fbdev: remove fb-puv3 driver
pwm: remove pwm-puv3 driver
input: i8042: remove support for 8042-unicore32io
i2c/buses: remove i2c-puv3 driver
cpufreq: remove unicore32 driver
arch: remove unicore32 port
Due to the lockless design of the driver, it is theoretically possible
to access a NULL pointer, if a slave interrupt was running while we were
unregistering the slave. To make this rock solid, disable the interrupt
for a short time while we are clearing the interrupt_enable register.
This patch is purely based on code inspection. The OOPS is super-hard to
trigger because clearing SAR (the address) makes interrupts even more
unlikely to happen as well. While here, reinit SCR to SDBS because this
bit should always be set according to documentation. There is no effect,
though, because the interface is disabled.
Fixes: 7b814d852a ("i2c: rcar: avoid race when unregistering slave client")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>