Fix data transfer width settings based on DT field 'spi-rx-bus-width'
to configure BSPI in single, dual or quad mode by using data width
and not the command width.
Fixes: 5f195ee7d8 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/1565086070-28451-1-git-send-email-rayagonda.kokatanur@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A bunch of small, device specific things here plus a DT bindings fix for
the new validatable YAML binding format. The most notable thing is the
fix for GPIO chip selects which fixes a corner case in updates of that
code to modern APIs, unfortunately due to a historical mess the code
around GPIO support is obscure, fragile and an ABI which makes and
attempt to improve the situation painful.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl1IQZkTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MR6B/4qcveQtV12fRqlYdd3JJjQY6oG4/bc
EMRp3Qfs5g9Wuurg4jbziVmcanymzRuNItNg/pVpFpYrmPeCHT7WyPdAnrAEXv2t
+P88pxayrOBXcitqqvQX+E2EXETj6ITsFVIYB9B2jsVAqaZChseT2JUhx+f+LbFW
BePekUWper4aBQLLEei9KcyAV7BANDl3NObqBYkqzu5/Em78eHRGmcPonvaToAWP
5DPqFu+w+TxhZyYaCJcNhUn9SaaInHexAdVVcatUuL14MyJ7J/5lPdjI55nof0ep
6wYXc85fV/dbsTjVl6uhEAll3ZsfBmyLztb3W0FMw4KeNKCDi1tOlcGB
=JOAs
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A bunch of small, device specific things here plus a DT bindings fix
for the new validatable YAML binding format.
The most notable thing is the fix for GPIO chip selects which fixes a
corner case in updates of that code to modern APIs, unfortunately due
to a historical mess the code around GPIO support is obscure, fragile
and an ABI which makes and attempt to improve the situation painful"
* tag 'spi-fix-v5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: Add support for Intel Tiger Lake
spi: bcm2835: Fix 3-wire mode if DMA is enabled
spi: pxa2xx: Balance runtime PM enable/disable on error
spi: gpio: Add SPI_MASTER_GPIO_SS flag
spi: spi-fsl-qspi: change i.MX7D RX FIFO size
spi: dt-bindings: spi-controller: remove unnecessary 'maxItems: 1' from reg
Driver specific implementations for .transfer_one_message need to call
the tracing stuff themself. This is necessary to make spi tracing
actually useful.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20190801204710.27309-1-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-42-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI thingies request FIFO-99 by default, reduce this to FIFO-50.
FIFO-99 is the very highest priority available to SCHED_FIFO and
it not a suitable default; it would indicate the SPI work is the
most important work on the machine.
Cc: Benson Leung <bleung@chromium.org>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20190801111541.917256884@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Tiger Lake -LP LPSS SPI controller is otherwise similar than
Cannon Lake but has more controllers and up to two chip selects per
controller.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20190801134901.12635-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the SPI slave control sysfs attribute from DEVICE_ATTR() to
DEVICE_ATTR_RW(), to reduce boilerplate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190731124738.14519-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
While there's one file there with briefily describes the uAPI,
the documentation was written just like most subsystems: focused
on kernel developers. So, add it together with driver-api books.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a generic helper to match a device by the ACPI_COMPANION device
and provide wrappers for the device lookup APIs.
Cc: Len Brown <lenb@kernel.org>
Cc: linux-acpi@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-i2c@vger.kernel.org
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # I2C parts
Link: https://lore.kernel.org/r/20190723221838.12024-6-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Spreadtrum ADI controller supplies multiple master accessing channel
to support multiple subsystems accessing, instead of using a hardware
spinlock to synchronize between the multiple subsystems.
To keep backward compatibility, we should change the hardware spinlock
to be optional. Moreover change to use of_hwspin_lock_get_id() function
which return -ENOENT error number to indicate no hwlock support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/2abe7dcf210e4197f8c5ece7fc6d6cc1eda8c655.1564125131.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When the system was rebooted by watchdog, now we did not save the watchdog
reset mode which will make system enter a incorrect mode after rebooting.
Thus we should set the watchdog reset mode as default when opening the
watchdog configuration, that means if the system was rebooted by other
reason through the restart_handler(), then we will clear the default
watchdog reset mode to save the correct reset mode.
Signed-off-by: Sherry Zong <sherry.zong@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/1563f3de43c6c2262d597a25d6138b5de61ea23d.1564125131.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6935224da2 ("spi: bcm2835: enable support of 3-wire mode")
added 3-wire support to the BCM2835 SPI driver by setting the REN bit
(Read Enable) in the CS register when receiving data. The REN bit puts
the transmitter in high-impedance state. The driver recognizes that
data is to be received by checking whether the rx_buf of a transfer is
non-NULL.
Commit 3ecd37edaa ("spi: bcm2835: enable dma modes for transfers
meeting certain conditions") subsequently broke 3-wire support because
it set the SPI_MASTER_MUST_RX flag which causes spi_map_msg() to replace
rx_buf with a dummy buffer if it is NULL. As a result, rx_buf is
*always* non-NULL if DMA is enabled.
Reinstate 3-wire support by not only checking whether rx_buf is non-NULL,
but also checking that it is not the dummy buffer.
Fixes: 3ecd37edaa ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Reported-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.2+
Cc: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/328318841455e505370ef8ecad97b646c033dc8a.1562148527.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
When optional clock requesting fails, the main clock is still up and running,
we should shut it down in such caee.
Fixes: 560ee7e910 ("spi: dw: Add support for an optional interface clock")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/20190710114243.30101-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't undo the PM initialization if we error out before we managed to
initialize it. The call to pm_runtime_disable() without being preceded
by pm_runtime_enable() would disturb the balance of the Force.
In practice, this happens if we fail to allocate any of the GPIOS ("cs",
"ready") due to -EPROBE_DEFER because we're getting probled before the
GPIO driver.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20190719122713.3444318-1-lkundrak@v3.sk
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO SPI master has some code in its local CS
callback to set the initial sck GPIO value. This was
lost in the commit converting it to use SPI core
GPIO handling as this callback isn't called if the
internal GPIO handling is active.
Add the special SPI_MASTER_GPIO_SS to ascertain it
gets called anyway so we get the initial SCK setting
right. There is some platform provided GPIO handling
there as well but this will be skipped as the cs_gpios
will be NULL.
My test targets seem not to care about the initial
SCK value so I am uncertain if this is a regression,
but to preserve the previous semantic we better do
this.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Fixes: 249e2632dc ("spi: gpio: Don't request CS GPIO in DT use-case")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190716204651.7743-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
When waking up from the Suspend-to-RAM state, the following error
was seen:
m25p80 spi2.0: flash operation timed out
The flash remained in an undefined state, returning 0xFFs.
Fix it by setting the Serial Clock Baud Rate, as it was set
before the conversion to SPIMEM.
Tested with sama5d2_xplained and mx25l25673g spi-nor in
Backup + Self-Refresh and Suspend modes.
Fixes: 0e6aae08e9 ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Reported-by: Mark Deneen <mdeneen@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 2d30ac5ed6 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
removed the error path from atmel_qspi_init(), but not changed the
function's return type. Set void return type for atmel_qspi_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible to request a transfer with a speed lower than supported
by the HW. This causes silent divider calculation underflow in
ssp_get_clk_div() which leads to a frequency higher than requested. Up to
maximum speed of the controller.
Set the minimum supported transfer speed and let the SPI core to
validate no transfers have speed lower than supported.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On umount step a sigkill signal is set (without user specific
action), due to sigkill signal the completion will be interrupted and
the data transfer can't be finished if a sync is needed.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The zero-length transfer results in timeout error because
the transfer doesn't start.
This commit modified to return success in this case.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Timeout error was silently ignored.
This commit adds timeout error handling and modifies return type of
wait_for_completion_timeout().
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the new SPI ACPI slave enumeration code, we use the value of
lookup.max_speed_khz as a flag to decide whether a match occurred.
However, doing so only makes sense if we initialize its value to
zero beforehand, or otherwise, random junk from the stack will
cause spurious matches.
So zero initialize the lookup struct fully, and only set the non-zero
members explicitly.
Fixes: 4c3c59544f ("spi/acpi: enumerate all SPI slaves in the namespace")
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: andy.shevchenko@gmail.com
Cc: masahisa.kojima@linaro.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On STM32 F4/F7/H7 SoCs, FTHRES is a 5 bits field in QSPI_CR register,
but for STM32MP1 SoCs, FTHRES is a 4 bits field long. CR_FTHRES_MASK
definition is not correct.
As for all these SoCs, FTHRES field is set to 3, FIELD_PREP() macro
is used with a constant as second parameter which make its usage useless.
CR_FTHRES_MASK and FIELD_PREP() can be removed.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
at91sam9g25ek showed the following error at probe:
atmel_spi f0000000.spi: Using dma0chan2 (tx) and dma0chan3 (rx)
for DMA transfers
atmel_spi: probe of f0000000.spi failed with error -22
Commit 0a919ae492 ("spi: Don't call spi_get_gpio_descs() before device name is set")
moved the calling of spi_get_gpio_descs() after ctrl->dev is set,
but didn't move the !ctrl->num_chipselect check. When there are
chip selects in the device tree, the spi-atmel driver lets the
SPI core discover them when registering the SPI master.
The ctrl->num_chipselect is thus expected to be set by
spi_get_gpio_descs().
Move the !ctlr->num_chipselect after spi_get_gpio_descs() as it was
before the aforementioned commit. While touching this block, get rid
of the explicit comparison with 0 and update the commenting style.
Fixes: 0a919ae492 ("spi: Don't call spi_get_gpio_descs() before device name is set")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kbuild test reported that alpha and some of the architectures
are missing readsl/writesl series.
Use more portable ioread32_rep()/iowrite32_rep() series.
Fixes: b0823ee35c ("spi: Add spi driver for Socionext SynQuacer platform")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 gpl
v2 as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081205.495444859@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation the gpl this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
version 2 gplv2 for more details you should have received a copy of
the gnu general public license version 2 gplv2 along with this
source code
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 16 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081201.771169395@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ACPI device object parsing code for SPI slaves enumerates the
entire ACPI namespace to look for devices that refer to the master
in question via the 'resource_source' field in the 'SPISerialBus'
resource. If that field does not refer to a valid ACPI device or
if it refers to the wrong SPI master, we should disregard the
device.
Current, the valid device check is wrong, since it gets the
polarity of 'status' wrong. This could cause issues if the
'resource_source' field is bogus but parent_handle happens to
refer to the correct master (which is not entirely imaginary
since this code runs in a loop)
So test for ACPI_FAILURE() instead, to make the code more
self explanatory.
Fixes: 4c3c59544f ("spi/acpi: enumerate all SPI slaves in the namespace")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: andy.shevchenko@gmail.com
Cc: masahisa.kojima@linaro.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The loop declaration in function spi_res_release() can be simplified
by reusing the common list_for_each_entry_safe_reverse() helper
macro.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device_for_each_child() doesn't require the returned value to be checked.
Thus, drop the dummy variable completely and have no warning anymore:
drivers/spi/spi.c: In function ‘spi_unregister_controller’:
drivers/spi/spi.c:2480:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
int dummy;
^~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the ACPI enumeration that takes place when registering a
SPI master only considers immediate child devices in the ACPI namespace,
rather than checking the ResourceSource field in the SpiSerialBus()
resource descriptor.
This is incorrect: SPI slaves could reside anywhere in the ACPI
namespace, and so we should enumerate the entire namespace and look for
any device that refers to the newly registered SPI master in its
resource descriptor.
So refactor the existing code and use a lookup structure so that
allocating the SPI device structure is deferred until we have identified
the device as an actual child of the controller. This approach is
loosely based on the way the I2C subsystem handles ACPI enumeration.
Note that Apple x86 hardware does not rely on SpiSerialBus() resources
in _CRS but uses nested devices below the controller's device node in
the ACPI namespace, with a special set of device properties. This means
we have to take care to only parse those properties for device nodes
that are direct children of the controller node.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-spi@vger.kernel.org
Cc: broonie@kernel.org
Cc: andy.shevchenko@gmail.com
Cc: masahisa.kojima@linaro.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- DMA/PIO:
If an error IRQ occurred during PIO or DMA mode make sure to log it so
on completion the transfer can be marked as an error.
- PIO:
Do not complete a transaction until all data has been transferred or
an error IRQ was flagged.
1) If there was no error IRQ, ignore the done flag IRQ
(QUP_OP_MAX_INPUT_DONE_FLAG) until all data for the transfer has been
processed: not doing so risks completing the transfer returning
uninitialized data in the buffers.
2) Under stress testing we have identified the need to
protect read/write operations against spurious IN/OUT service events.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A small set of fixes here, one core fix for error handling when we fail
to set up the hardware before initiating a transfer and another one
reverting a change in the core which broke Raspberry Pi in common use
cases as part of some optimization work. There's also a couple of
driver specific fixes.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlz+aEETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0EdhB/9pSAaTxpo2LmLY11WDqCll5E5wwV0n
twjqcJkCpik2gp08xf/l1C563XvaAEUmidMGjpSGNhbd+UFUY4jBksDZd8t+phNA
lOFL03sWxUGd46SvsYCLByzIu1dp8LKQ7JkDvb+OChDMai9YyeHwF4Pl7L7EHI6P
yB3m84o3X82NnVxZJZAkim27Bn1LMcmKvFJxiLPyzycdI41+Vzf+Hx0dSzTKHKXb
wbh3tsSok1l3NHOW0xXCf8pG5KtBeISo7RxQE2XuVkxB3LcEbbbG+Q1NvBHQLmty
VtSkLUGc3+mUdaaIh2CW3AkECRtkPG6qngBns0NScXca4xQ9/J3X4zlg
=ktil
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small set of fixes here.
One core fix for error handling when we fail to set up the hardware
before initiating a transfer and another one reverting a change in the
core which broke Raspberry Pi in common use cases as part of some
optimization work.
There's also a couple of driver specific fixes"
* tag 'spi-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: abort spi_sync if failed to prepare_transfer_hardware
spi: spi-fsl-spi: call spi_finalize_current_message() at the end
spi: bitbang: Fix NULL pointer dereference in spi_unregister_master
spi: Fix Raspberry Pi breakage
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct spi_replaced_transfers {
...
struct spi_transfer inserted_transfers[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
insert * sizeof(struct spi_transfer) + sizeof(struct spi_replaced_transfers)
with:
struct_size(rxfer, inserted_transfers, insert)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can distribute it and or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope it will be useful but without any warranty
without even the implied warranty of merchantability or fitness for
a particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 24 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.872212424@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is released under the gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 68 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license rev 2 and only
rev 2 as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.583753585@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can distribute it and or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081035.310807637@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
may be copied or modified under the terms of the gnu general public
license version 2 [0] [only] see linux copying for more information
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.341514676@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gplv2 this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.986607096@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for controller found on synquacer platforms.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove unnecessary condition check and associated goto.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 82 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible string for Menlosystems CPLD present on the M53Menlo
board. This CPLD is used to communicate with various custom sensors.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-spi@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
While the Hardware User Manual does not document the maximum time needed
for modifying bits in the MSIOF Control Register, experiments on R-Car
Gen2/Gen3 and SH-Mobile AG5 revealed the following typical modification
times for the various bits:
- CTR.TXE and CTR.RXE: no delay,
- CTR.TSCKE: less than 10 ns,
- CTR.TFSE: up to a few hundred ns (depending on SPI transfer clock,
i.e. less for faster transfers).
There are no reasons to believe these figures are different for
SH-MobileR2 SoCs (SH7723/SH7724).
Hence the minimum busy-looping delay of 10 µs is excessive.
Reduce the delay per loop iteration from 10 to 1 us, and the maximum
delay from 1000 to 100 µs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation either version 2 of the
license or at your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170857.824091446@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now the only way to get the SPI pumping thread bumped up to
realtime priority is for the controller to request it. However it may
be that the controller works fine with the normal priority but
communication to a particular SPI device on the bus needs realtime
priority.
Let's add a way for devices to request realtime priority when they set
themselves up.
NOTE: this will just affect the priority of transfers that end up on
the SPI core's pumping thread. In many cases transfers happen in the
context of the caller so if you need realtime priority for all
transfers you should ensure the calling context is also realtime
priority.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch sets master cleanup and also invokes tegra spi clean on
tegra spi probe failure to release tegra spi client data.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 SPI driver still sets the "direction" member in struct
dma_slave_config even though it was deprecated five years ago with
commit d9ff958bb3 ("dmaengine: Mark the struct dma_slave_config
direction field deprecated") and is no longer evaluated by the BCM2835
DMA driver since commit 00648f4d0f ("dmaengine: bcm2835: remove
dma_slave_config direction usage").
Drop the superfluous assignment.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8caab75fd2 ('spi: Generalize SPI "master" to "controller"')
changed the "spi_master" nomenclature to "spi_controller", necessitating
a conversion of all drivers.
Perform this conversion for the BCM2835 SPI driver.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_finalize_current_message() shall be called once all
actions are finished, otherwise the last actions might
step over a newly started transfer.
Fixes: c592becbe7 ("spi: fsl-(e)spi: migrate to generic master queueing")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare to use devices on the external SPI interface
on a DH electronics Development Board.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers
-----BEGIN PGP SIGNATURE-----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=YSfu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
Tegra SPI master controller has programmable trimmers to adjust the
data with respect to the clock.
These trimmers are programmed in TX_CLK_TAP_DELAY and RX_CLK_TAP_DELAY
fields of COMMAND2 register.
SPI TX trimmer is to adjust the outgoing data with respect to the
outgoing clock and SPI RX trimmer is to adjust the loopback clock with
respect to the incoming data from the slave device.
These trimmers vary based on trace lengths of the platform design for
each of the slaves on the SPI bus and optimal value programmed is from
the platform validation across PVT.
This patch adds support for configuring TX and RX clock delay trimmers
through the device tree properties.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implements set_cs_timing SPI controller method to allow
SPI client driver to configure device specific SPI CS timings.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra SPI controller supports both HW and SW based CS control
for SPI transfers.
This patch adds support for HW based CS control where CS is driven
to active state during the transfer and is driven inactive at the
end of the transfer directly by the HW.
This patch enables the use of HW based CS only for single transfers
without cs_change request.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for GPIO based CS control through SPI core
function spi_set_cs.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kthread.h can't be included in psi_types.h because it creates a circular
inclusion with kthread.h eventually including psi_types.h and
complaining on kthread structures not being defined because they are
defined further in the kthread.h. Resolve this by removing psi_types.h
inclusion from the headers included from kthread.h.
Link: http://lkml.kernel.org/r/20190319235619.260832-7-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no use for this when performing non DMA operations. So we
bypass the split.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
ARCH_BRCMSTB platforms have the BCM2835 SPI controllers (normal and
auxiliary), allow selecting the two drivers on such platforms.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Printing an error on memory allocation failure is unnecessary,
as the memory allocation core code already takes care of that.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Printing an error on memory allocation failure is unnecessary,
as the memory allocation core code already takes care of that.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a means for the spi bus driver to report the effectively used
spi clock frequency used for each spi_transfer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and
support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips
and support for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
rcar-dmac, stm32-dma etc
- dev_get_drvdata() updates on few drivers
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJc08p1AAoJEHwUBw8lI4NHD14QAJGU7MOc9dpr+qtm2k3sNO3o
EXZtb3GjTs4MUt6EfMA47KXsxeq4UhubQqM7CmPngDyjXaPd4JBE8bwAd+OzS9sq
eAPMa+M1g8MehuQcdUzB/y6APoSFhGvFoGLY8e7FeI6fwYNm3Yy2gTSiZfpMb3MW
hclJQe+UWfppUHOig13tr0tbQ31DOa7qb2+roVJqDEb9sQ5bDkhRWXjElfoeSXsS
n8nNh4GZr5RkIxfzslVRZNfqb1lja2e03SXBsN9faQI7BfIYBM+9hWSYd4Nq8uYo
xvhYf9gJnKVKtFrwdXtyeBJ80DijWBoodhLrLOfhEYYOrCl9WwJT9AepIOdvij32
11FwjCbkC9ASQ1cSLyRUBbdmfykSlBvdbAMwJc1y9qK7k9BMba3rXRJfimlRy29A
Cpsu4tZKoPlZRGinoGnEGreg1YZI1YHwa+hlkW/8V9Zkb2hvIUbbXr7xHedJf7n4
gIb5DnCF5pC1umB/o7pj2YXrYBc9GETp3sDQ88aw1owKh1T2pZcc5HOpi4p7/7n+
b2HM0cWOCM3aKwdOcONk0jd87FcYQm3g1isQF5SCOtOys8Uy6wNqo9aRrfE/94aw
4SiGRq9/nSOHDh72mD3Ux7v47/cFjWGzZZJVy5+NC+Mq79KxgpXOjsIr7YVbcn9m
GuUdiDZmUvZ4y+qq/uCI
=JDU6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
This reverts commit c9ba7a16d0 (Release spi_res after finalizing
message) which causes races during cleanup.
Reported-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes tx and bi-directional dma transfers on rk3399-gru-kevin.
It seems the SPI fifo must have room for 2 bursts when the dma_tx_req
signal is generated or it might skip some words. This in turn makes
the rx dma channel never complete for bi-directional transfers.
Fix it by setting tx burst length to fifo_len / 4 and the dma
watermark to fifo_len / 2.
However the rk3399 TRM says (sic):
"DMAC support incrementing-address burst and fixed-address burst. But in
the case of access SPI and UART at byte or halfword size, DMAC only
support fixed-address burst and the address must be aligned to word."
So this relies on fifo_len being a multiple of 16 such that the
burst length (= fifo_len / 4) is a multiple of 4 and the addresses
will be word-aligned.
Fixes: dcfc861d24 ("spi: rockchip: adjust dma watermark and burstlen")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support setting a delay between cs assert and deassert as
a multiple of spi clock length.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some SPI devices that support speed_hz > 1MHz the default 10 us delay
when cs_change = 1 is typically way to long and may result in poor spi bus
utilization.
This patch makes it possible to control the delay at micro or nano second
resolution on a per spi_transfer basis. It even allows an "as fast as
possible" mode with:
xfer.cs_change_delay_unit = SPI_DELAY_UNIT_NSECS;
xfer.cs_change_delay = 0;
The delay code is shared between delay_usecs and cs_change_delay for
consistency and reuse, so in the future this change_delay_unit could also
apply to delay_usec as well.
Note that on slower SOCs/CPU actually reaching ns deasserts on cs is not
realistic as the gpio overhead alone (without any delays added ) may
already leave cs deasserted for more than 1us - at least on a raspberry pi.
But at the very least this way we can keep it as short as possible.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To estimate efficiency add statistics on transfer types
(polling, interrupt and dma) used to debugfs.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions
fixed compile issue when CONFIG_DEBUG_FS is unset
Signed-off-by: Mark Brown <broonie@kernel.org>
Under some circumstances the default 30 us polling limit is not optimal
and may lead to long delays because we are waiting on an interrupt.
with this patch we have the possibility to influence this policy.
So make this limit (in us) configurable via a module parameters
(but also modifyable via /sys/modules/...)
This replicates similar code found in spi-bcm2835aux.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA mode behaves slightly different than polling or interrupt driven
mode, so just document the fact
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
new in V2
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid 64 bit aritmetics when deciding if we need to use polling or not
This replicates: commit d704afffe6
("spi: bcm2835aux: Avoid 64-bit arithmetic in xfer len calc")
from spi-bcm2835aux
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unnecessary argument of xfer_time_us when calling
bcm2835_spi_transfer_one_poll.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for DMA. Transfers are done with dma only if
they are longer than 16 bytes in order to achieve a better performance.
DMA setup introduces a little overhead and for transfers shorter than 16
bytes there is no performance improvement.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Mark Brown <broonie@kernel.org>
My previous patch leaves a dangling variable in the driver.
get rid of it.
Fixes: 06a391b1621e ("spi: ep93xx: Convert to use CS GPIO descriptors")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here, along
with some new IIO drivers.
Also we ended up deleting two drivers, making this pull request remove a
few hundred thousand lines of code, always a nice thing to see. Both of
the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from those
locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by the
various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come in
the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHGMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynQRACgwtlC6DFsEFwCplYxQXP5uzuIVTMAoJ61xzC0
Qim7K31f5ulaa3GJuhzo
=zEY5
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
https://lore.kernel.org/linux-fsdevel/CAHk-=wg1tFzcaX2v9Z91vPJiBR486ddW5MtgDL02-fOen2F0Aw@mail.gmail.com/T/#m5b2d9ad3aeacea4bd6aa1964468ac074bf3aa5bf
-----BEGIN PGP SIGNATURE-----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=Mavg
-----END PGP SIGNATURE-----
Merge tag 'stream_open-5.2' of https://lab.nexedi.com/kirr/linux
Pull stream_open conversion from Kirill Smelkov:
- remove unnecessary double nonseekable_open from drivers/char/dtlk.c
as noticed by Pavel Machek while reviewing nonseekable_open ->
stream_open mass conversion.
- the mass conversion patch promised in commit 10dce8af34 ("fs:
stream_open - opener for stream-like files so that read and write can
run simultaneously without deadlock") and is automatically generated
by running
$ make coccicheck MODE=patch COCCI=scripts/coccinelle/api/stream_open.cocci
I've verified each generated change manually - that it is correct to
convert - and each other nonseekable_open instance left - that it is
either not correct to convert there, or that it is not converted due
to current stream_open.cocci limitations. More details on this in the
patch.
- finally, change VFS to pass ppos=NULL into .read/.write for files
that declare themselves streams. It was suggested by Rasmus Villemoes
and makes sure that if ppos starts to be erroneously used in a stream
file, such bug won't go unnoticed and will produce an oops instead of
creating illusion of position change being taken into account.
Note: this patch does not conflict with "fuse: Add FOPEN_STREAM to
use stream_open()" that will be hopefully coming via FUSE tree,
because fs/fuse/ uses new-style .read_iter/.write_iter, and for these
accessors position is still passed as non-pointer kiocb.ki_pos .
* tag 'stream_open-5.2' of https://lab.nexedi.com/kirr/linux:
vfs: pass ppos=NULL to .read()/.write() of FMODE_STREAM files
*: convert stream-like files from nonseekable_open -> stream_open
dtlk: remove double call to nonseekable_open
One small feature was added this release but the bulk of the diffstat
and the changelog comes from the fact that several older drivers got
some fairly hefty reworks and a couple of new drivers were added:
- Support for detailed control of timing around chip selects from
Sowjanya Komatineni.
- A big set of fixes and imrovements for the Tegra114 driver from
Sowjanya Komatineni.
- A big simplification of the GPIO driver from Andrey Smirnov.
- DMA support and fixes for the Freescale LPSPI driver from Clark Wang.
- Fixes and optimizations for the bcm2835aux from Martin Sparl.
- New drivers for Mediatek MT7621 (graduated from staging) and Zynq QSPI.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlzQRTQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GgAB/96xMofBtfeSNdZgXiF5a8LSDDmzJAF
VMy66Q0VN5JgF8bH11KIZKho/T4PgNaGdbOtBZN/bt+vKhO7ZdaGp4bdtKXLogr/
bKJ102mdFBHTNtOuY3wXJtHcYRj1TPx528weOu/VbUo/Yt+e3yRybMiVjOvuQGn8
KrSQvQRlqaZcxYBVEMg3AQB3dkTFo5/hN9ipWjrabApFhcSbybA6Ccd/2VB2JD2H
lJ04atW+hP9zQOhQJUolI5QGkRtHwV2t+iohMrqjW7bacGdbILfORgoKqpxTMaCl
vT7+2CV3OtGC0OZWdlzGrLPOMG94/nbXjzmfGuJ4KX9WiTEJcadt7OR1
=1Dfk
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"One small feature was added this release but the bulk of the diffstat
and the changelog comes from the fact that several older drivers got
some fairly hefty reworks and a couple of new drivers were added:
- Support for detailed control of timing around chip selects from
Sowjanya Komatineni.
- A big set of fixes and imrovements for the Tegra114 driver from
Sowjanya Komatineni.
- A big simplification of the GPIO driver from Andrey Smirnov.
- DMA support and fixes for the Freescale LPSPI driver from Clark
Wang.
- Fixes and optimizations for the bcm2835aux from Martin Sparl.
- New drivers for Mediatek MT7621 (graduated from staging) and Zynq
QSPI"
[ This is a so-called "evil merge" that additionally removes a warning
due to an unused variable 'i' introduced by commit 1dfbf334f1 ("spi:
ep93xx: Convert to use CS GPIO descriptors") - Linus ]
* tag 'spi-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (127 commits)
spi: rspi: Fix handling of QSPI code when transmit and receive
spi: atmel-quadspi: fix crash while suspending
spi: stm32: return the get_irq error
spi: tegra114: fix PIO transfer
spi: pxa2xx: fix SCR (divisor) calculation
spi: Clear SPI_CS_HIGH flag from bad_bits for GPIO chip-select
spi: ep93xx: Convert to use CS GPIO descriptors
spi: AD ASoC: declare missing of table
spi: spi-mem: zynq-qspi: Fix build error on architectures missing readsl/writesl
spi: stm32-qspi: manage the get_irq error case
spi/spi-bcm2835: Split transfers that exceed DLEN
spi: expand mode support
dt-bindings: spi: spi-mt65xx: add support for MT8516
spi: pxa2xx: Add support for Intel Comet Lake
spi/trace: Cap buffer contents at 64 bytes
spi: Release spi_res after finalizing message
spi: Remove warning in spi_split_transfers_maxsize()
spi: Remove one needless transfer speed fall back case
spi: sh-msiof: Document r8a77470 bindings
spi: pxa2xx: use a module softdep for dw_dmac
...
Using scripts/coccinelle/api/stream_open.cocci added in 10dce8af34
("fs: stream_open - opener for stream-like files so that read and write
can run simultaneously without deadlock"), search and convert to
stream_open all in-kernel nonseekable_open users for which read and
write actually do not depend on ppos and where there is no other methods
in file_operations which assume @offset access.
I've verified each generated change manually - that it is correct to convert -
and each other nonseekable_open instance left - that it is either not correct
to convert there, or that it is not converted due to current stream_open.cocci
limitations. The script also does not convert files that should be valid to
convert, but that currently have .llseek = noop_llseek or generic_file_llseek
for unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Among cases converted 14 were potentially vulnerable to read vs write deadlock
(see details in 10dce8af34):
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/infiniband/core/user_mad.c:988:1-17: ERROR: umad_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/input/misc/uinput.c:401:1-17: ERROR: uinput_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write(); change nonseekable_open -> stream_open to fix.
and the rest were just safe to convert to stream_open because their read and
write do not use ppos at all and corresponding file_operations do not
have methods that assume @offset file access(*):
arch/powerpc/platforms/52xx/mpc52xx_gpt.c:631:8-24: WARNING: mpc52xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_ibox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_mbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/powerpc/platforms/cell/spufs/file.c:591:8-24: WARNING: spufs_wbox_stat_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/um/drivers/harddog_kern.c:88:8-24: WARNING: harddog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
arch/x86/kernel/cpu/microcode/core.c:430:33-49: WARNING: microcode_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ds1620.c:215:8-24: WARNING: ds1620_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/dtlk.c:301:1-17: WARNING: dtlk_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/ipmi/ipmi_watchdog.c:840:9-25: WARNING: ipmi_wdog_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/pcmcia/scr24x_cs.c:95:8-24: WARNING: scr24x_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/char/tb0219.c:246:9-25: WARNING: tb0219_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/firewire/nosy.c:306:8-24: WARNING: nosy_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/fschmd.c:840:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/hwmon/w83793.c:1344:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucma.c:1747:8-24: WARNING: ucma_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/ucm.c:1178:8-24: WARNING: ucm_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/infiniband/core/uverbs_main.c:1086:8-24: WARNING: uverbs_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/input/joydev.c:282:1-17: WARNING: joydev_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/pci/switch/switchtec.c:393:1-17: WARNING: switchtec_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/platform/chrome/cros_ec_debugfs.c:135:8-24: WARNING: cros_ec_console_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-ds1374.c:470:9-25: WARNING: ds1374_wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/rtc/rtc-m41t80.c:805:9-25: WARNING: wdt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/tape_char.c:293:2-18: WARNING: tape_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/char/zcore.c:194:8-24: WARNING: zcore_reipl_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/s390/crypto/zcrypt_api.c:528:8-24: WARNING: zcrypt_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/spi/spidev.c:594:1-17: WARNING: spidev_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/staging/pi433/pi433_if.c:974:1-17: WARNING: pi433_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/acquirewdt.c:203:8-24: WARNING: acq_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/advantechwdt.c:202:8-24: WARNING: advwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim1535_wdt.c:252:8-24: WARNING: ali_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/alim7101_wdt.c:217:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ar7_wdt.c:166:8-24: WARNING: ar7_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/at91rm9200_wdt.c:113:8-24: WARNING: at91wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ath79_wdt.c:135:8-24: WARNING: ath79_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/bcm63xx_wdt.c:119:8-24: WARNING: bcm63xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpu5wdt.c:143:8-24: WARNING: cpu5wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/cpwd.c:397:8-24: WARNING: cpwd_fops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/eurotechwdt.c:319:8-24: WARNING: eurwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/f71808e_wdt.c:528:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/gef_wdt.c:232:8-24: WARNING: gef_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/geodewdt.c:95:8-24: WARNING: geodewdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ib700wdt.c:241:8-24: WARNING: ibwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ibmasr.c:326:8-24: WARNING: asr_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/indydog.c:80:8-24: WARNING: indydog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/intel_scu_watchdog.c:307:8-24: WARNING: intel_scu_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/iop_wdt.c:104:8-24: WARNING: iop_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/it8712f_wdt.c:330:8-24: WARNING: it8712f_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ixp4xx_wdt.c:68:8-24: WARNING: ixp4xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/ks8695_wdt.c:145:8-24: WARNING: ks8695wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/m54xx_wdt.c:88:8-24: WARNING: m54xx_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/machzwd.c:336:8-24: WARNING: zf_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mixcomwd.c:153:8-24: WARNING: mixcomwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mtx-1_wdt.c:121:8-24: WARNING: mtx1_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/mv64x60_wdt.c:136:8-24: WARNING: mv64x60_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nuc900_wdt.c:134:8-24: WARNING: nuc900wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/nv_tco.c:164:8-24: WARNING: nv_tco_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pc87413_wdt.c:289:8-24: WARNING: pc87413_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:698:8-24: WARNING: pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd.c:737:8-24: WARNING: pcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:581:8-24: WARNING: pcipcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_pci.c:623:8-24: WARNING: pcipcwd_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:488:8-24: WARNING: usb_pcwd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pcwd_usb.c:527:8-24: WARNING: usb_pcwd_temperature_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pika_wdt.c:121:8-24: WARNING: pikawdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/pnx833x_wdt.c:119:8-24: WARNING: pnx833x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rc32434_wdt.c:153:8-24: WARNING: rc32434_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/rdc321x_wdt.c:145:8-24: WARNING: rdc321x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/riowd.c:79:1-17: WARNING: riowd_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sa1100_wdt.c:62:8-24: WARNING: sa1100dog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc60xxwdt.c:211:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc7240_wdt.c:139:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc8360.c:274:8-24: WARNING: sbc8360_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_epx_c3.c:81:8-24: WARNING: epx_c3_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sbc_fitpc2_wdt.c:78:8-24: WARNING: fitpc2_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sb_wdog.c:108:1-17: WARNING: sbwdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc1200wdt.c:181:8-24: WARNING: sc1200wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sc520_wdt.c:261:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/sch311x_wdt.c:319:8-24: WARNING: sch311x_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/scx200_wdt.c:105:8-24: WARNING: scx200_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/smsc37b787_wdt.c:369:8-24: WARNING: wb_smsc_wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83877f_wdt.c:227:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/w83977f_wdt.c:301:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wafer5823wdt.c:200:8-24: WARNING: wafwdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/watchdog_dev.c:828:8-24: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:379:8-24: WARNING: wdrtas_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdrtas.c:445:8-24: WARNING: wdrtas_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt285.c:104:1-17: WARNING: watchdog_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt977.c:276:8-24: WARNING: wdt977_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:424:8-24: WARNING: wdt_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt.c:484:8-24: WARNING: wdt_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:464:8-24: WARNING: wdtpci_fops: .write() has stream semantic; safe to change nonseekable_open -> stream_open.
drivers/watchdog/wdt_pci.c:527:8-24: WARNING: wdtpci_temp_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
net/batman-adv/log.c:105:1-17: WARNING: batadv_log_fops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/control.c:57:7-23: WARNING: snd_ctl_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/rawmidi.c:385:7-23: WARNING: snd_rawmidi_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/seq/seq_clientmgr.c:310:7-23: WARNING: snd_seq_f_ops: .read() and .write() have stream semantic; safe to change nonseekable_open -> stream_open.
sound/core/timer.c:1428:7-23: WARNING: snd_timer_f_ops: .read() has stream semantic; safe to change nonseekable_open -> stream_open.
One can also recheck/review the patch via generating it with explanation comments included via
$ make coccicheck MODE=patch COCCI=scripts/coccinelle/api/stream_open.cocci SPFLAGS="-D explain"
(*) This second group also contains cases with read/write deadlocks that
stream_open.cocci don't yet detect, but which are still valid to convert to
stream_open since ppos is not used. For example drivers/pci/switch/switchtec.c
calls wait_for_completion_interruptible() in its .read, but stream_open.cocci
currently detects only "wait_event*" as blocking.
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yongzhi Pan <panyongzhi@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Nikolaus Rath <Nikolaus@rath.org>
Cc: Han-Wen Nienhuys <hanwen@google.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James R. Van Zandt" <jrv@vanzandt.mv.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Lubomir Rintel <lkundrak@v3.sk> [scr24x_cs]
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: David Herrmann <dh.herrmann@googlemail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Jean Delvare <jdelvare@suse.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> [watchdog/* hwmon/*]
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com> [drivers/pci/switch/switchtec]
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [drivers/pci/switch/switchtec]
Cc: Benson Leung <bleung@chromium.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> [platform/chrome]
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> [rtc/*]
Cc: Mark Brown <broonie@kernel.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Zwane Mwaikambo <zwanem@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Process handling QSPI when transmit/receive at qspi_trigger_transfer_out_in() as follows:
Setting the trigger, is the number of bytes in the FIFO buffer to determine
when there is an interrupt. Then check if the value of triggering number is
32-bytes or 1-byte, there will be corresponding processing
Handling (if (n == QSPI_BUFFER_SIZE) esle) this is unnecessary, leads to the
same processing of data transmission or reception, The difference here are with
ret = rspi_wait_for_tx_empty(rspi);
ret = rspi_wait_for_rx_full(rspi);
When the nummber trigger is 32 bytes, we only write into FIFO when the FIFO is completely empty
(interrupt transmission), and only receive if FIFO is full of 32 bytes of data.
In the case of a nummber trigger that is 1 byte, in principle we still need to process
rspi_wait_for_tx_empty/full so that FIFO is empty only with the amount of data we need to write to
or equal to the number of bytes we need to receive, There is currently no processing of this.
And in the current case with this patch, at this time it only needs at least 1 byte received in
FIFO that has interrupt received, or FIFO at least 1bytes free can be written into FIFO,
This patch therefore does not affect this processing.
So we need to eliminate unnecessary waste processing (if (n == QSPI_BUFFER_SIZE) esle),
more precisely in waiting for FIFO status.
The same with handling in qspi_transfer_out()/qspi_transfer_in().
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
atmel_qspi objects are kept in spi_controller objects, so, first get
pointer to spi_controller object and then get atmel_qspi object from
spi_controller object.
Fixes: 2d30ac5ed6 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During probe, return the "get_irq" error value instead of -ENOENT. This
allows the driver to be defer probed if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes PIO mode transfer to use PIO bit in SPI_COMMAND1 register.
Current driver uses DMA_EN instead of PIO bit.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Calculate the divisor for the SCR (Serial Clock Rate), avoiding
that the SSP transmission rate can be greater than the device rate.
When the division between the SSP clock and the device rate generates
a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the
device SPI max frequency.
For example, with:
- ssp_clk = 50 MHz
- dev freq = 15 MHz
without this patch the SSP clock will be greater than 15 MHz:
- 25 MHz for PXA25x_SSP and CE4100_SSP
- 16,56 MHz for the others
Instead, with this patch, we have in both case an SSP clock of 12.5MHz,
so the max rate of the SPI device clock is respected.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When GPIO chip-select is used nothing prevents any available SPI
controllers to work with both CS-high and traditional CS-low modes.
In fact the SPI bus core code already does it, so we don't need to
introduce any modification there. But spi_setup() still fails to
switch the interface settings if CS-high flag is set for the case
of GPIO-driven slave chip-select when the SPI controller doesn't
support the hardwired CS-inversion. Lets fix it by clearing the
SPI_CS_HIGH flag out from bad_bits (unsupported by controller) when
client chip is selected by GPIO.
This feature is useful for slave devices, which in accordance with
communication protocol can work with both active-high and active-low
chip-selects. I am aware of one such device. It is MMC-SPI interface,
when at init sequence the driver needs to perform a read operation with
low and high chip-select sequentially (requirement of 74 clock cycles
with both chipselect, see the mmc_spi driver for details).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the EP93xx SPI master driver to use GPIO
descriptors for chip select handling.
EP93xx was using platform data to pass in GPIO lines,
by converting all board files to use GPIO descriptor
tables the core will look up the GPIO lines from the
SPI device in the same manner as for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Alpha and some of the architectures are missing readsl/writesl functions.
so the zynq-qspi driver won't be able to build on these arches. hence use
ioread32_rep()/iowrite32_rep() instead of readsl()/writesl().
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During probe, check the "get_irq" error value.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split spi transfers into chunks of <=65532 to enable the driver to
perform DMA transfer on big buffers. The DLEN register specifies the
number of bytes to transfer in DMA mode. It is 16-bit wide and thus the
maximum DMA transfer is 65535 bytes. Set the maximum to 65532 (4 byte
aligned) since the FIFO in DMA mode is accessed in 4 byte chunks.
->max_dma_len is the value the spi core uses when splitting the buffer
into scatter gather entries.
The BCM2835 DMA block has 2 types of channels/engines:
- Normal: Max length: 1G
- Lite: Max length: 65535
Even when using a Lite channel we will not exceed the max length, so
let's drop setting ->max_dma_len.
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PCI IDs for SPI on Comet Lake.
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_split_transfers_maxsize() can be used to split a transfer. This
function uses spi_res to lifetime manage the added transfer structures.
So in order to finalize the current message while it contains the split
transfers, spi_res_release() must be called after finalizing.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't warn about splitting transfers, the info is available in the
statistics if needed.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Falling back to maximum speed of the controller in case of SPI slave
maximum speed is not set is needless. It already defaults to maximum
speed of the controller since commit 052eb2d490 ("spi: core: Set
max_speed_hz of spi_device default to max_speed_hz of controller").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With dw_dmac, sometimes the request of a DMA channel fails because
the DMA driver is not ready, so an explicit dependency request
is necessary.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
Missing include:
drivers/spi/spi-zynqmp-gqspi.c:1025:13: error: implicit declaration of
function 'zynqmp_pm_get_eemi_ops'; did you mean
'zynqmp_process_dma_irq'? [-Werror=implicit-function-declaration]
Fixes: 3d03137864 ('drivers: Defer probe if firmware is not ready')
Cc: Rajan Vaja <rajan.vaja@xilinx.com>
Cc: Jolly Shah <jollys@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch creates set_cs_timing SPI master optional method for
SPI masters to implement configuring CS timing if applicable.
This patch also creates spi_cs_timing accessory for SPI clients to
use for requesting SPI master controllers to configure device requested
CS setup time, hold time and inactive delay.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch creates tegra_spi_soc_data structure to maintain and implement
SPI HW feature differences between different Tegra chips and also creates
a separate compatible string for T124/T210.
Tegra210 and later has a separate interrupt mask register SPI_INTR_MASK
for enabling or disabling interrupts while Tegra124 and prior uses
interrupt enable bits in SPI_DMA_CTL register.
This patch creates flag has_intr_mask_reg in tegra_spi_soc_data to
identify this and implements accordingly.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds 3 wire transfer support to SPI mode list along with
its implementation.
3 wire or Bi-directional mode uses only one serial data pin for the
transfer. SPI in master mode uses MOSI data line only and MISO data
line is not used.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for dual mode SPI transfer.
Dual mode uses both MOSI and MISO lines in parallel where the data
is interleaved on MOSI and MISO lines increasing the throughput.
Packet from Tx FIFO is transmitted on both MOSI and MISO lines and
packet to Rx FIFO is received from both MOSI and MISO lines. Even
bits are transmitted or received on the MOSI data line and odd bits
are transmitted or received on the MISO data line.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace spi_bitbang_start() with a combination of spi_bitbang_init()
and devm_spi_register_master() and drop all of the explicit
cleanup-related code that's no longer necessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all of the code doing struct spi_bitbang initialization, so that
it can be paired with devm_spi_register_master() in order to avoid
having to call spi_bitbang_stop() explicitly.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a number of failure paths in spi_gpio_probe() that do not call
spi_master_put() potentially leaking memory. Fix this problem by
registering a cleanup funciont via devm_add_action_or_reset() right
after SPI controller is allocated.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the type of the diagnostic message:
"no DMA channels available, using PIO"
from debug to warning.
The lack of an available DMA channel is very important regard the
spi-pxa2xx performance. The transfer speed can be reduced more than 50%.
So it is very important to warn the user about this, without enabling
the full SPI debug with CONFIG_SPI_DEBUG.
Moreover, enabling the full SPI debug only to enable this specific
debug message, the dmesg buffer fills quickly with a lot of
repetitive information during the SPI data transfer.
This cause the loss of all the first important messages
written during the initialization.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use is_slave local variable to avoid calling of_property_read_bool() twice.
Remove redudant assignment for controller->bus_num, set it once is enough.
Move setting controller->bits_per_word_mask close to the code init other
controller fields.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add #ifdef CONFIG_PM guard to fix build warning when !CONFIG_PM
drivers/spi/spi-fsl-lpspi.c:810:12: warning: ‘fsl_lpspi_runtime_suspend’ defined but not used [-Wunused-function]
static int fsl_lpspi_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-fsl-lpspi.c:789:12: warning: ‘fsl_lpspi_runtime_resume’ defined but not used [-Wunused-function]
static int fsl_lpspi_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original code already set controller as drvdata:
platform_set_drvdata(pdev, controller);
But commit 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
added dev_set_drvdata(&pdev->dev, fsl_lpspi);
so fsl_lpspi_remove() will get wrong pointer by platform_get_drvdata().
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function names in the kernel-doc comments were mistyped, with a word
"dirmap" being repeated twice, so fix them.
Fixes: aa167f3fed ("spi: spi-mem: Add a new API to support direct mapping")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building CONFIG_DEBUG_FS is not set
gcc warn this:
drivers/spi/spi-bcm2835aux.c: In function bcm2835aux_spi_probe:
drivers/spi/spi-bcm2835aux.c:591:2: error: too many arguments to function bcm2835aux_debugfs_create
bcm2835aux_debugfs_create(bs, dev_name(&pdev->dev));
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:145:13: note: declared here
static void bcm2835aux_debugfs_create(struct bcm2835aux_spi *bs)
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8048d151eb ("spi: bcm2835aux: add driver stats to debugfs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'status' local variable is initialized but this value is never used,
thus kill that initializer.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for QSPI controller driver used by Xilinx Zynq SOC.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no code using 'pdev' field in struct spi_gpio. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic of setting mflags in spi_gpio_request() is very simple and
there isn't much benefit in having it in that function. Move all of
that code outside into spi_gpio_probe() in order to simplify things.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Move code calling spi_get_gpio_descs() to happen after ctlr->dev's
name is set in order to have proper GPIO consumer names.
Before:
cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/40049000.gpio, vf610-gpio:
gpio-6 ( |regulator-usb0-vbus ) out lo
gpiochip1: GPIOs 32-63, parent: platform/4004a000.gpio, vf610-gpio:
gpio-36 ( |scl ) in hi
gpio-37 ( |sda ) in hi
gpio-40 ( |(null) CS1 ) out lo
gpio-41 ( |(null) CS0 ) out lo ACTIVE LOW
gpio-42 ( |miso ) in hi
gpio-43 ( |mosi ) in lo
gpio-44 ( |sck ) out lo
After:
cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/40049000.gpio, vf610-gpio:
gpio-6 ( |regulator-usb0-vbus ) out lo
gpiochip1: GPIOs 32-63, parent: platform/4004a000.gpio, vf610-gpio:
gpio-36 ( |scl ) in hi
gpio-37 ( |sda ) in hi
gpio-40 ( |spi0 CS1 ) out lo
gpio-41 ( |spi0 CS0 ) out lo ACTIVE LOW
gpio-42 ( |miso ) in hi
gpio-43 ( |mosi ) in lo
gpio-44 ( |sck ) out lo
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
DT use-case already relies on SPI core to control CS (requested by
of_spi_register_master() and controlled spi_set_cs()), so there's no
need to try to request those GPIO in spi-gpio code. Change the code
such that spi-gpio's CS related code is only used if device is probed
via pdata.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch sets SPI device id from the device tree as the bus number.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Packed mode expects minimum transfer length of 4 bytes.
This patch fixes this by using unpacked mode for transfers less
than 4 bytes.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra SPI supports 4 through 32 bits per word.
This patch sets bits_per_word_mask accordingly to support transfer
with these bits per word.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch dumps SPI registers on transfer error or timeout for debug
purpose.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves SPI controller reset out of spin lock.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With SW CS, during the transfer completion CS is de-asserted by writing
default command1 register value to SPI_COMMAND1 register. With this both
mode and CS state are set at the same time and if current transfer mode
is different to default SPI mode and if mode change happens prior to CS
de-assert, clock polarity can change while CS is active before transfer
finishes.
This causes Slave to see spurious clock edges resulting in data mismatch.
This patch fixes this by de-asserting CS before writing SPI_COMMAND1 to
its default value so through out the transfer it will be in same SPI mode.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert GPIO chip selects in the Renesas MSIOF SPI driver from legacy
GPIO numbers to GPIO descriptors.
Notes:
- The board file for the SH7724-based Ecovec24 development board now
registers a GPIO descriptor lookup, instead of passing a GPIO number
through controller_data,
- sh_msiof_get_cs_gpios() must release all GPIOs, else
spi_get_gpio_descs() cannot claim them during SPI controller
registration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 5fd917afc4 ("spi: bcm2835aux: make the polling duration limits configurable")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While devm_gpiod_get_index_optional() returns NULL if the GPIO is not
present (i.e. -ENOENT), it may still return other error codes, like
-EPROBE_DEFER. Currently these are not handled, leading to
unrecoverable failures later in case of probe deferral:
gpiod_set_consumer_name: invalid GPIO (errorpointer)
gpiod_direction_output: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
gpiod_set_value_cansleep: invalid GPIO (errorpointer)
Detect and propagate errors to fix this.
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from GPIO numbers to GPIO descriptors removed the use of
spi->controller_data, but forgot to update a comment referring to it.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
To estimate efficiency add statistics on transfer types
(polling and interrupt) used to debugfs.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In accordance with hardware specification Ver 1.0, reset register
transmission / reception setting before transfer.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Use readl_poll_timeout_atomic()]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the open-coded loop in sh_msiof_modify_ctr_wait() by a call to
the readl_poll_timeout_atomic() helper macro.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing complete operations for dma_completion to fix the
problem of blocking at the wait_for_completion_interruptible()
function when use spi_slave_abort().
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop unused pdata copy in struct spi_gpio. No functional change
intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Swap branches of the if statement in order to simplify it's logical
condition being checked. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a local "struct spi_bitbang *bb" in spi_gpio_probe() for
brevity. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a local "struct device *dev" in spi_gpio_probe() for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Spi_to_pdata() is not used anywhere in the code. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Under some circumstances the default 30 us polling limit is not optimal
and may lead to long delays because we are waiting on an interrupt.
with this patch we have the possibility to influence this policy.
So make this limit (in us) configurable via a module parameters
(but also modifyable via /sys/modules/...)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup gpio-cs to the correct levels during setup and also make the
gpio definitely an output GPIO.
This is transparently fixing some badly configured DTs in the process
where cs-gpio is set but the gpios are still configured with native cs.
It also makes 100% sure that the initial CS levels are as expected -
especially on systems with devices on a bus with mixed CS_HIGH/CS_LOW
settings.
Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
From personal bad experience (even as the author of the original driver)
it shows that native-cs is "somewhat" supported by the spi bus driver
when using a buggy device tree.
So make sure that the driver is warning in dmesg about this fact
that we are running in a not supported mode that may have surprizing
limitations.
Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original driver by default defines num_chipselects as -1.
This actually allicates an array of 65535 entries in
of_spi_register_master.
There is a side-effect for buggy device trees that (contrary to
dt-binding documentation) have no cs-gpio defined.
This mode was never supported by the driver due to limitations
of native cs and additional code complexity and is explicitly
not stated to be implemented.
To keep backwards compatibility with such buggy DTs we limit
the number of chip_selects to 1, as for all practical purposes
it is only ever realistic to use a single chip select in
native cs mode without negative side-effects.
Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove dead code that never can get reached, as we limit count to
a max of 3.
Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On long running tests with a mcp2517fd can controller it showed that
on rare occations the data read shows corruptions for longer spi transfers.
Example of a 22 byte transfer:
expected (as captured on logic analyzer):
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 85 86 87 88 89 8a 8b
read by the driver:
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 88 89 8a 00 00 8b 9b
To fix this use BCM2835_AUX_SPI_STAT_RX_LVL to determine when we may
read data from the fifo reliably without any corruption.
Surprisingly the only values ever empirically read in
BCM2835_AUX_SPI_STAT_RX_LVL are 0x00, 0x10, 0x20 and 0x30.
So whenever the mask is not 0 we can read from the fifo in a safe manner.
The patch has now been tested intensively and we are no longer
able to reproduce the "RX" issue any longer.
Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Reported-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This read of the fifo is a potential candidate for a race condition
as the spi transfer is not necessarily finished and so can lead to
an early read of the fifo that still misses data.
So it has been removed.
Fixes: 1ea29b39f4 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sharing more code between polling and interrupt-driven mode.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export spi_mem_default_supports_op(), so that controller drivers
can use this.
spi-mem driver already exports this using EXPORT_SYMBOL,
but not declared it in spi-mem.h.
This patch declares spi_mem_default_supports_op() in spi-mem.h and
also removes the static from the function prototype.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Improve maintainability by converting the register bit, bitmask, and
bitfield definitions from hexadecimal constants to constructs using
BIT(), GENMASK(), or "val << shift".
Suggested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit c9bfcb3151 (spi_mpc83xx: much improved driver) introduced
logic to ensure bits_per_word and speed_hz stay the same for a series
of spi_transfers with CS active, arguing that
The current driver may cause glitches on SPI CLK line since one
must disable the SPI controller before changing any HW settings.
This sounds quite reasonable. So this is a quite naive attempt at
relaxing this sanity checking to only ensure that speed_hz is
constant - in the faint hope that if we do not causes changes to the
clock-related fields of the SPMODE register (DIV16 and PM), those
glitches won't appear.
The purpose of this change is to allow automatically optimizing large
transfers to use 32 bits-per-word; taking one interrupt for every byte
is extremely slow.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use SPI device pointer in the remaining two error and warning prints in
pxa2xx_spi_transfer_one() instead of platform device of the controller
It make prints in the function uniform and more useful especially the
error print here as it can reveal the driver that has mapped the DMA
itself and attempts to transfer more than the maximum supported DMA
transfer length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pointer to a SPI device is passed to pxa2xx_spi_transfer_one() so there
is no need to access it through the current SPI message pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra SPI controller supports lsb first mode. Default is MSB bit first
and on selection of SPI_LSB_FIRST through SPI mode transmission happens
with LSB bit first.
This patch adds SPI_LSB_FIRST flag to mode_bits and also configures it
on request.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: Use packed mode for 32 bits per word transfers to increase
performance as each packet is a full 32-bit word.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment says that we should not allow changes (to
bits_per_word/speed_hz) while CS is active, and indeed the code below
does fsl_spi_setup_transfer() when the ->cs_change of the previous
spi_transfer was set (and for the very first transfer).
So the sanity checking is a bit too strict - we can change it to
follow the same logic as is used by the actual transfer loop.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
__spi_validate() in the generic SPI code sets ->speed_hz and
->bits_per_word to non-zero values, so this condition is always true.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: SPI driver can be built as module so perform SPI controller reset
on probe to make sure it is in valid state before initiating transfer.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: Configure DMA burst size to be same as SPI TX/RX trigger levels
to avoid mismatch.
SPI FIFO trigger levels are calculated based on the transfer length.
So this patch moves DMA slave configuration to happen before start
of DMAs.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: Flush TX and RX FIFOs before start of new transfer and on FIFO
overflow or underrun errors.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: terminate DMA and perform controller reset on transfer timeout
to clear the FIFO's and errors.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: computation of actual bytes to fill/receive in/from FIFO in unpacked
mode when transfer length is not a multiple of requested bits per word.
unpacked mode transfers fails when the transfer includes partial bytes in
the last word.
Total words to be written/read to/from FIFO is computed based on transfer
length and bits per word. Unpacked mode includes 0 padding bytes for partial
words to align with bits per word and these extra bytes are also accounted
for calculating bytes left to transfer in the current driver.
This causes extra bytes access of tx/rx buffers along with buffer index
position crossing actual length where remain_len becomes negative and due to
unsigned type, negative value is a 32 bit representation of signed value
and transferred bytes never meets the actual transfer length resulting in
transfer timeout and a hang.
This patch fixes this with proper computation of the actual bytes to fill in
FIFO during transmit and the actual bytes to read from FIFO during receive
ignoring 0 padded bytes.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: Clear packed bit when not using packed mode.
Packed bit is not cleared when not using packed mode. This results
in transfer timeouts for the unpacked mode transfers followed by the
packed mode transfers.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When timeout occurs DMA TX and RX channels should be stopped
instead of stopping RX channel twice time.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To transfer via SPI the tegra20-slink driver first sets the command
register, which contains the chip select value, and after that the
command2 register, which contains the chip select line. This leads to a
small spike in the chip selct 0 line between the set of the value and
the selection of the chip select line.
This commit changes the order of the register writes so that first the
chip select line is chosen and then the value is set, removing the
spike.
Signed-off-by: Randolph Maaßen <gaireg@gaireg.de>
Reviewed-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the dma support for the stm32-qspi hardware.
The memory buffer constraints (lowmem, vmalloc, kmap) are taken into
account by framework. In read mode, the memory map is preferred vs
dma (due to better throughput). If the dma transfer fails the buffer
is sent by polling.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds spi_master_put in release function
to drop the controller's refcount.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the MT7621 SPI driver, which is used on some Ralink /
MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to
the source code are done in this patch.
This driver version was tested successfully on an MT7688 based platform
with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so
far).
This patch also documents the devicetree bindings for the MT7621 SPI
device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: NeilBrown <neil@brown.name>
Cc: Sankalp Negi <sankalpnegi2310@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Armando Miraglia <arma2ff0@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This checking is already done in __spi_validate_bits_per_word().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rayagonda Kokatanur