If a port is unused, still create a devlink port for it, but set the
flavour to unused. This allows us to attach devlink regions to the
port, etc.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are guaranteed that dsa_untag_bridge_pvid() is called after
eth_type_trans() we can utilize __vlan_find_dev_deep_rcu() which will
take care of finding an 802.1Q upper on top of a bridge master.
A common use case, prior to 12a1526d067 ("net: dsa: untag the bridge
pvid from rx skbs") was to configure a bridge 802.1Q upper like this:
ip link add name br0 type bridge vlan_filtering 0
ip link add link br0 name br0.1 type vlan id 1
in order to pop the default_pvid VLAN tag.
With this change we restore that behavior while still allowing the DSA
receive path to automatically pop the VLAN tag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that dsa_untag_bridge_pvid() is called after eth_type_trans() we are
guaranteed that skb->protocol will be set to a correct value, thus
allowing us to avoid calling vlan_eth_hdr().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver needs to call dsa_untag_bridge_pvid(), it can
set dsa_switch::untag_brige_pvid to indicate this is necessary.
This is a pre-requisite to making sure that we are always calling
dsa_untag_bridge_pvid() after eth_type_trans() has been called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 is a bit of a special snowflake, in that not all frames are
transmitted/received in the same way. L2 link-local frames are received
with the source port/switch ID information put in the destination MAC
address. For the rest, a tag_8021q header is used. So only the latter
frames displace the rest of the headers and need to use the generic flow
dissector procedure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: John Crispin <john@phrozen.org>
Cc: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 Broadcom tags in use, one places the DSA tag before the
Ethernet destination MAC address, and the other before the EtherType.
Nonetheless, both displace the rest of the headers, so this tagger can
use the generic flow dissector procedure which accounts for that.
The ASCII art drawing is a good reference though, so keep it but move it
somewhere else.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Tell that to the DSA core, since this makes a difference for the flow
dissector. Most switches break the parsing of frame headers, but these
ones don't, so no flow dissector adjustment needs to be done for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no tagger that returns anything other than zero, so just change
the return type appropriately.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PTP is broken when ports are in standalone mode (the tagger
keeps printing this message):
sja1105 spi0.1: Expected meta frame, is 01-80-c2-00-00-0e in the DSA master multicast filter?
Sure, one might say "simply add 01-80-c2-00-00-0e to the master's RX
filter" but things become more complicated because:
- Actually all frames in the 01-80-c2-xx-xx-xx and 01-1b-19-xx-xx-xx
range are trapped to the CPU automatically
- The switch mangles bytes 3 and 4 of the MAC address via the incl_srcpt
("include source port [in the DMAC]") option, which is how source port
and switch id identification is done for link-local traffic on RX. But
this means that an address installed to the RX filter would, at the
end of the day, not correspond to the final address seen by the DSA
master.
Assume RX filtering lists on DSA masters are typically too small to
include all necessary addresses for PTP to work properly on sja1105, and
just request promiscuous mode unconditionally.
Just an example:
Assuming the following addresses are trapped to the CPU:
01-80-c2-00-00-00 to 01-80-c2-00-00-ff
01-1b-19-00-00-00 to 01-1b-19-00-00-ff
These are 512 addresses.
Now let's say this is a board with 3 switches, and 4 ports per switch.
The 512 addresses become 6144 addresses that must be managed by the DSA
master's RX filtering lists.
This may be refined in the future, but for now, it is simply not worth
it to add the additional addresses to the master's RX filter, so simply
request it to become promiscuous as soon as the driver probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA assumes that taggers don't mess with the destination MAC
address of the frames on RX. That is not always the case. Some DSA
headers are placed before the Ethernet header (ocelot), and others
simply mangle random bytes from the destination MAC address (sja1105
with its incl_srcpt option).
Currently the DSA master goes to promiscuous mode automatically when the
slave devices go too (such as when enslaved to a bridge), but in
standalone mode this is a problem that needs to be dealt with.
So give drivers the possibility to signal that their tagging protocol
will get randomly dropped otherwise, and let DSA deal with fixing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.
This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the B53 driver to support VLANs while not filtering. This
requires us to enable VLAN globally within the switch upon driver
initial configuration (dev->vlan_enabled).
We also need to remove the code that dealt with PVID re-configuration in
b53_vlan_filtering() since that function worked under the assumption
that it would only be called to make a bridge VLAN filtering, or not
filtering, and we would attempt to move the port's PVID accordingly.
Now that VLANs are programmed all the time, even in the case of a
non-VLAN filtering bridge, we would be programming a default_pvid for
the bridged switch ports.
We need the DSA receive path to pop the VLAN tag if it is the bridge's
default_pvid because the CPU port is always programmed tagged in the
programmed VLANs. In order to do so we utilize the
dsa_untag_bridge_pvid() helper introduced in the commit before within
net/dsa/tag_brcm.c.
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge untags VLANs present in its VLAN groups in
__allowed_ingress() only when VLAN filtering is enabled.
But when a skb is seen on the RX path as tagged with the bridge's pvid,
and that bridge has vlan_filtering=0, and there isn't any 8021q upper
with that VLAN either, then we have a problem. The bridge will not untag
it (since it is supposed to remain VLAN-unaware), and pvid-tagged
communication will be broken.
There are 2 situations where we can end up like that:
1. When installing a pvid in egress-tagged mode, like this:
ip link add dev br0 type bridge vlan_filtering 0
ip link set swp0 master br0
bridge vlan del dev swp0 vid 1
bridge vlan add dev swp0 vid 1 pvid
This happens because DSA configures the VLAN membership of the CPU port
using the same flags as swp0 (in this case "pvid and not untagged"), in
an attempt to copy the frame as-is from ingress to the CPU.
However, in this case, the packet may arrive untagged on ingress, it
will be pvid-tagged by the ingress port, and will be sent as
egress-tagged towards the CPU. Otherwise stated, the CPU will see a VLAN
tag where there was none to speak of on ingress.
When vlan_filtering is 1, this is not a problem, as stated in the first
paragraph, because __allowed_ingress() will pop it. But currently, when
vlan_filtering is 0 and we have such a VLAN configuration, we need an
8021q upper (br0.1) to be able to ping over that VLAN, which is not
symmetrical with the vlan_filtering=1 case, and therefore, confusing for
users.
Basically what DSA attempts to do is simply an approximation: try to
copy the skb with (or without) the same VLAN all the way up to the CPU.
But DSA drivers treat CPU port VLAN membership in various ways (which is
a good segue into situation 2). And some of those drivers simply tell
the CPU port to copy the frame unmodified, which is the golden standard
when it comes to VLAN processing (therefore, any driver which can
configure the hardware to do that, should do that, and discard the VLAN
flags requested by DSA on the CPU port).
2. Some DSA drivers always configure the CPU port as egress-tagged, in
an attempt to recover the classified VLAN from the skb. These drivers
cannot work at all with untagged traffic when bridged in
vlan_filtering=0 mode. And they can't go for the easy "just keep the
pvid as egress-untagged towards the CPU" route, because each front port
can have its own pvid, and that might require conflicting VLAN
membership settings on the CPU port (swp1 is pvid for VID 1 and
egress-tagged for VID 2; swp2 is egress-taggeed for VID 1 and pvid for
VID 2; with this simplistic approach, the CPU port, which is really a
separate hardware entity and has its own VLAN membership settings, would
end up being egress-untagged in both VID 1 and VID 2, therefore losing
the VLAN tags of ingress traffic).
So the only thing we can do is to create a helper function for resolving
the problematic case (that is, a function which untags the bridge pvid
when that is in vlan_filtering=0 mode), which taggers in need should
call. It isn't called from the generic DSA receive path because there
are drivers that fall neither in the first nor second category.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether there is any hwaccel VLAN tag on RX, and if there is,
treat it as the tag_8021q header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole purpose of tag_8021q is to send VLAN-tagged traffic to the
CPU, from which the driver can decode the source port and switch id.
Currently this only works if the VLAN filtering on the master is
disabled. Change that by explicitly adding code to tag_8021q.c to add
the VLANs corresponding to the tags to the filter of the master
interface.
Because we now need to call vlan_vid_add, then we also need to hold the
RTNL mutex. Propagate that requirement to the callers of dsa_8021q_setup
and modify the existing call sites as appropriate. Note that one call
path, sja1105_best_effort_vlan_filtering_set -> sja1105_vlan_filtering
-> sja1105_setup_8021q_tagging, was already holding this lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most DSA switch tags shift the EtherType to the right, causing the
master to not parse the VLAN as VLAN.
However, not all switches do that (example: tail tags, tag_8021q etc),
and if the DSA master has "rx-vlan-filter: on" in ethtool -k, then we
have a problem.
Therefore, we could populate the VLAN table of the master, just in case
(for some switches it will not make a difference), so that network I/O
can work even with a VLAN filtering master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge has VLAN awareness disabled there isn't any duplication
of functionality, since the bridge does not process VLAN. Don't deny
adding 8021q uppers to DSA switch ports in that case. The switch is
supposed to simply pass traffic leaving the VLAN tag as-is, and the
stack will happily strip the VLAN tag for all 8021q uppers that exist.
We need to ensure that there are no 8021q uppers when the user attempts
to enable bridge vlan_filtering.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic beats me a little bit. The comment that "bridge skips
-EOPNOTSUPP, so skip the prepare phase" was introduced in commit
fb2dabad69 ("net: dsa: support VLAN filtering switchdev attr").
I'm not sure:
(a) ok, the bridge skips -EOPNOTSUPP, but, so what, where are we
returning -EOPNOTSUPP?
(b) even if we are, and I'm just not seeing it, what is the causality
relationship between the bridge skipping -EOPNOTSUPP and DSA
skipping the prepare phase, and just returning zero?
One thing is certain beyond doubt though, and that is that DSA currently
refuses VLAN filtering from the "commit" phase instead of "prepare", and
that this is not a good thing:
ip link add br0 type bridge
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br1
[ 3790.379389] 001: sja1105 spi0.1: VLAN filtering is a global setting
[ 3790.379399] 001: ------------[ cut here ]------------
[ 3790.379403] 001: WARNING: CPU: 1 PID: 515 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 3790.379420] 001: swp3: Commit of attribute (id=6) failed.
[ 3790.379533] 001: [<c11ff588>] (switchdev_port_attr_set_now) from [<c11b62e4>] (nbp_vlan_init+0x84/0x148)
[ 3790.379544] 001: [<c11b62e4>] (nbp_vlan_init) from [<c11a2ff0>] (br_add_if+0x514/0x670)
[ 3790.379554] 001: [<c11a2ff0>] (br_add_if) from [<c1031b5c>] (do_setlink+0x38c/0xab0)
[ 3790.379565] 001: [<c1031b5c>] (do_setlink) from [<c1036fe8>] (__rtnl_newlink+0x44c/0x748)
[ 3790.379573] 001: [<c1036fe8>] (__rtnl_newlink) from [<c1037328>] (rtnl_newlink+0x44/0x60)
[ 3790.379580] 001: [<c1037328>] (rtnl_newlink) from [<c10315fc>] (rtnetlink_rcv_msg+0x124/0x2f8)
[ 3790.379590] 001: [<c10315fc>] (rtnetlink_rcv_msg) from [<c10926b8>] (netlink_rcv_skb+0xb8/0x110)
[ 3790.379806] 001: ---[ end trace 0000000000000002 ]---
[ 3790.379819] 001: sja1105 spi0.1 swp3: failed to initialize vlan filtering on this port
So move the current logic that may fail (except ds->ops->port_vlan_filtering,
that is way harder) into the prepare stage of the switchdev transaction.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is checking for the following order of operations, and makes sure
to deny that configuration:
ip link add link swp2 name swp2.100 type vlan id 100
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan add dev swp2 vid 100
Instead of using vlan_for_each(), which looks at the VLAN filters
installed with vlan_vid_add(), just track the 8021q uppers. This has the
advantage of freeing up the vlan_vid_add() call for actual VLAN
filtering.
There is another change in this patch. The check is moved in slave.c,
from switch.c. I don't think it makes sense to have this 8021q upper
check for each switch port that gets notified of that VLAN addition
(these include DSA links and CPU ports, we know those can't have 8021q
uppers because they don't have a net_device registered for them), so
just do it in slave.c, for that one slave interface.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA tries to prevent having a VLAN added by a bridge and by an 802.1Q
upper at the same time. It does that by checking the VID in
.ndo_vlan_rx_add_vid(), since that's something that the 8021q module
calls, via vlan_vid_add(). When a VLAN matches in both subsystems, this
check returns -EBUSY.
However the vlan_vid_add() function isn't specific to the 8021q module
in any way at all. It is simply the kernel's way to tell an interface to
add a VLAN to its RX filter and not drop that VLAN. So there's no reason
to return -EBUSY when somebody tries to call vlan_vid_add() for a VLAN
that was installed by the bridge. The proper behavior is to accept that
configuration.
So what's wrong is how DSA checks that it has an 8021q upper. It should
look at the actual uppers for that, not just assume that the 8021q
module was somewhere in the call stack of .ndo_vlan_rx_add_vid().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll be adding a new check in the PRECHANGEUPPER notifier, where we'll
need to check some VLAN uppers. It is hard to do that when there is
already a function named dsa_slave_upper_vlan_check. So rename this one.
Not to mention that this function probably shouldn't have started with
"dsa_slave_" in the first place, since the struct net_device argument
isn't a DSA slave, but an 8021q upper of one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There doesn't seem to be any strong technical reason for doing it this
way, but we'll be adding more checks for invalid upper device
configurations, and it will be easier to have them all grouped under
PRECHANGEUPPER.
Tested that it still works:
ip link set br0 type bridge vlan_filtering 1
ip link add link swp2 name swp2.100 type vlan id 100
ip link set swp2.100 master br0
[ 20.321312] br0: port 5(swp2.100) entered blocking state
[ 20.326711] br0: port 5(swp2.100) entered disabled state
Error: dsa_core: Cannot enslave VLAN device into VLAN aware bridge.
[ 20.346549] br0: port 5(swp2.100) entered blocking state
[ 20.351957] br0: port 5(swp2.100) entered disabled state
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the DSA drivers to implement the devlink call to get info info,
e.g. driver name, firmware version, ASIC ID, etc.
v2:
Combine declaration and the assignment on a single line.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA drivers to make use of devlink regions, via simple wrappers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given a devlink instance, return the dsa switch it is associated to.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb8299 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 314f76d7a6.
Citing that commit message, the call graph was:
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Now that tag_8021q has its own ops structure, it no longer relies on
dsa_port_vid_add, and therefore on the dsa_switch_ops to install its
VLANs.
So dsa_port_vid_add now only has one single caller. So we can simplify
the call graph to what it was before, aka:
dsa_slave_vlan_rx_add_vid dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on another tag_8021q driver implementation, some things
became apparent:
- It is not mandatory for a DSA driver to offload the tag_8021q VLANs by
using the VLAN table per se. For example, it can add custom TCAM rules
that simply encapsulate RX traffic, and redirect & decapsulate rules
for TX traffic. For such a driver, it makes no sense to receive the
tag_8021q configuration through the same callback as it receives the
VLAN configuration from the bridge and the 8021q modules.
- Currently, sja1105 (the only tag_8021q user) sets a
priv->expect_dsa_8021q variable to distinguish between the bridge
calling, and tag_8021q calling. That can be improved, to say the
least.
- The crosschip bridging operations are, in fact, stateful already. The
list of crosschip_links must be kept by the caller and passed to the
relevant tag_8021q functions.
So it would be nice if the tag_8021q configuration was more
self-contained. This patch attempts to do that.
Create a struct dsa_8021q_context which encapsulates a struct
dsa_switch, and has 2 function pointers for adding and deleting a VLAN.
These will replace the previous channel to the driver, which was through
the .port_vlan_add and .port_vlan_del callbacks of dsa_switch_ops.
Also put the list of crosschip_links into this dsa_8021q_context.
Drivers that don't support cross-chip bridging can simply omit to
initialize this list, as long as they dont call any cross-chip function.
The sja1105_vlan_add and sja1105_vlan_del functions are refactored into
a smaller sja1105_vlan_add_one, which now has 2 entry points:
- sja1105_vlan_add, from struct dsa_switch_ops
- sja1105_dsa_8021q_vlan_add, from the tag_8021q ops
But even this change is fairly trivial. It just reflects the fact that
for sja1105, the VLANs from these 2 channels end up in the same hardware
table. However that is not necessarily true in the general sense (and
that's the reason for making this change).
The rest of the patch is mostly plain refactoring of "ds" -> "ctx". The
dsa_8021q_context structure needs to be propagated because adding a VLAN
is now done through the ops function pointers inside of it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in calling dsa_port_setup_8021q_tagging for each
individual port. Additionally, it will become more difficult to do that
when we'll have a context structure to tag_8021q (next patch). So
refactor this now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 845e0ebb44 ("net: change addr_list_lock back to static
key"), cascaded DSA setups (DSA switch port as DSA master for another
DSA switch port) are emitting this lockdep warning:
============================================
WARNING: possible recursive locking detected
5.8.0-rc1-00133-g923e4b5032dd-dirty #208 Not tainted
--------------------------------------------
dhcpcd/323 is trying to acquire lock:
ffff000066dd4268 (&dsa_master_addr_list_lock_key/1){+...}-{2:2}, at: dev_mc_sync+0x44/0x90
but task is already holding lock:
ffff00006608c268 (&dsa_master_addr_list_lock_key/1){+...}-{2:2}, at: dev_mc_sync+0x44/0x90
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&dsa_master_addr_list_lock_key/1);
lock(&dsa_master_addr_list_lock_key/1);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by dhcpcd/323:
#0: ffffdbd1381dda18 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x24/0x30
#1: ffff00006614b268 (_xmit_ETHER){+...}-{2:2}, at: dev_set_rx_mode+0x28/0x48
#2: ffff00006608c268 (&dsa_master_addr_list_lock_key/1){+...}-{2:2}, at: dev_mc_sync+0x44/0x90
stack backtrace:
Call trace:
dump_backtrace+0x0/0x1e0
show_stack+0x20/0x30
dump_stack+0xec/0x158
__lock_acquire+0xca0/0x2398
lock_acquire+0xe8/0x440
_raw_spin_lock_nested+0x64/0x90
dev_mc_sync+0x44/0x90
dsa_slave_set_rx_mode+0x34/0x50
__dev_set_rx_mode+0x60/0xa0
dev_mc_sync+0x84/0x90
dsa_slave_set_rx_mode+0x34/0x50
__dev_set_rx_mode+0x60/0xa0
dev_set_rx_mode+0x30/0x48
__dev_open+0x10c/0x180
__dev_change_flags+0x170/0x1c8
dev_change_flags+0x2c/0x70
devinet_ioctl+0x774/0x878
inet_ioctl+0x348/0x3b0
sock_do_ioctl+0x50/0x310
sock_ioctl+0x1f8/0x580
ksys_ioctl+0xb0/0xf0
__arm64_sys_ioctl+0x28/0x38
el0_svc_common.constprop.0+0x7c/0x180
do_el0_svc+0x2c/0x98
el0_sync_handler+0x9c/0x1b8
el0_sync+0x158/0x180
Since DSA never made use of the netdev API for describing links between
upper devices and lower devices, the dev->lower_level value of a DSA
switch interface would be 1, which would warn when it is a DSA master.
We can use netdev_upper_dev_link() to describe the relationship between
a DSA slave and a DSA master. To be precise, a DSA "slave" (switch port)
is an "upper" to a DSA "master" (host port). The relationship is "many
uppers to one lower", like in the case of VLAN. So, for that reason, we
use the same function as VLAN uses.
There might be a chance that somebody will try to take hold of this
interface and use it immediately after register_netdev() and before
netdev_upper_dev_link(). To avoid that, we do the registration and
linkage while holding the RTNL, and we use the RTNL-locked cousin of
register_netdev(), which is register_netdevice().
Since this warning was not there when lockdep was using dynamic keys for
addr_list_lock, we are blaming the lockdep patch itself. The network
stack _has_ been using static lockdep keys before, and it _is_ likely
that stacked DSA setups have been triggering these lockdep warnings
since forever, however I can't test very old kernels on this particular
stacked DSA setup, to ensure I'm not in fact introducing regressions.
Fixes: 845e0ebb44 ("net: change addr_list_lock back to static key")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 72579e14a1 ("net: dsa: don't fail to probe if we couldn't set
the MTU") changed, for some reason, the "err && err != -EOPNOTSUPP"
check into a simple "err". This causes the MTU warning to be printed
even for drivers that don't have the MTU operations implemented.
Fix that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
slave_dev->name is only populated at this stage if it was specified
through a label in the device tree. However that is not mandatory.
When it isn't, the error message looks like this:
[ 5.037057] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
[ 5.044672] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
[ 5.052275] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
[ 5.059877] fsl_enetc 0000:00:00.2 eth2: error -19 setting up slave PHY for eth%d
which is especially confusing since the error gets printed on behalf of
the DSA master (fsl_enetc in this case).
Printing an error message that contains a valid reference to the DSA
port's name is difficult at this point in the initialization stage, so
at least we should print some info that is more reliable, even if less
user-friendly. That may be the driver name and the hardware port index.
After this change, the error is printed as:
[ 6.051587] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 0
[ 6.061192] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 1
[ 6.070765] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 2
[ 6.080324] mscc_felix 0000:00:00.5: error -19 setting up PHY for tree 0, switch 0, port 3
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The purpose of this override is to give the user an indication of what
the number of the CPU port is (in DSA, the CPU port is a hardware
implementation detail and not a network interface capable of traffic).
However, it has always failed (by design) at providing this information
to the user in a reliable fashion.
Prior to commit 3369afba1e ("net: Call into DSA netdevice_ops
wrappers"), the behavior was to only override this callback if it was
not provided by the DSA master.
That was its first failure: if the DSA master itself was a DSA port or a
switchdev, then the user would not see the number of the CPU port in
/sys/class/net/eth0/phys_port_name, but the number of the DSA master
port within its respective physical switch.
But that was actually ok in a way. The commit mentioned above changed
that behavior, and now overrides the master's ndo_get_phys_port_name
unconditionally. That comes with problems of its own, which are worse in
a way.
The idea is that it's typical for switchdev users to have udev rules for
consistent interface naming. These are based, among other things, on
the phys_port_name attribute. If we let the DSA switch at the bottom
to start randomly overriding ndo_get_phys_port_name with its own CPU
port, we basically lose any predictability in interface naming, or even
uniqueness, for that matter.
So, there are reasons to let DSA override the master's callback (to
provide a consistent interface, a number which has a clear meaning and
must not be interpreted according to context), and there are reasons to
not let DSA override it (it breaks udev matching for the DSA master).
But, there is an alternative method for users to retrieve the number of
the CPU port of each DSA switch in the system:
$ devlink port
pci/0000:00:00.5/0: type eth netdev swp0 flavour physical port 0
pci/0000:00:00.5/2: type eth netdev swp2 flavour physical port 2
pci/0000:00:00.5/4: type notset flavour cpu port 4
spi/spi2.0/0: type eth netdev sw0p0 flavour physical port 0
spi/spi2.0/1: type eth netdev sw0p1 flavour physical port 1
spi/spi2.0/2: type eth netdev sw0p2 flavour physical port 2
spi/spi2.0/4: type notset flavour cpu port 4
spi/spi2.1/0: type eth netdev sw1p0 flavour physical port 0
spi/spi2.1/1: type eth netdev sw1p1 flavour physical port 1
spi/spi2.1/2: type eth netdev sw1p2 flavour physical port 2
spi/spi2.1/3: type eth netdev sw1p3 flavour physical port 3
spi/spi2.1/4: type notset flavour cpu port 4
So remove this duplicated, unreliable and troublesome method. From this
patch on, the phys_port_name attribute of the DSA master will only
contain information about itself (if at all). If the users need reliable
information about the CPU port they're probably using devlink anyway.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to unified Ethernet Switch Device Tree Bindings allow for ethernet-ports as
encapsulating node as well.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA supports MTU configuration, undo the effects of commit
8b1efc0f83 ("net: remove MTU limits on a few ether_setup callers") and
let DSA interfaces use the default min_mtu and max_mtu specified by
ether_setup(). This is more important for min_mtu: since DSA is
Ethernet, the minimum MTU is the same as of any other Ethernet
interface, and definitely not zero. For the max_mtu, we have a callback
through which drivers can override that, if they want to.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have all the infrastructure in place for calling into the
dsa_ptr->netdev_ops function pointers, install them when we configure
the DSA CPU/management interface and tear them down. The flow is
unchanged from before, but now we preserve equality of tests when
network device drivers do tests like dev->netdev_ops == &foo_ops which
was not the case before since we were allocating an entirely new
structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, devlink_port_attrs_set accepts a long list of parameters,
that most of them are devlink port's attributes.
Use the devlink_port_attrs struct to replace the relevant parameters.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the known parts of the Realtek 4 byte
tag protocol version 0xA, as found in the RTL8366RB
DSA switch.
It is designated as protocol version 0xA as a
different Realtek 4 byte tag format with protocol
version 0x9 is known to exist in the Realtek RTL8306
chips.
The tag and switch chip lacks public documentation, so
the tag format has been reverse-engineered from
packet dumps. As only ingress traffic has been available
for analysis an egress tag has not been possible to
develop (even using educated guesses about bit fields)
so this is as far as it gets. It is not known if the
switch even supports egress tagging.
Excessive attempts to figure out the egress tag format
was made. When nothing else worked, I just tried all bit
combinations with 0xannp where a is protocol and p is
port. I looped through all values several times trying
to get a response from ping, without any positive
result.
Using just these ingress tags however, the switch
functionality is vastly improved and the packets find
their way into the destination port without any
tricky VLAN configuration. On the D-Link DIR-685 the
LAN ports now come up and respond to ping without
any command line configuration so this is a real
improvement for users.
Egress packets need to be restricted to the proper
target ports using VLAN, which the RTL8366RB DSA
switch driver already sets up.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa/tag_qca.c:48:15: warning: incorrect type in assignment (different base types)
net/dsa/tag_qca.c:48:15: expected unsigned short [usertype]
net/dsa/tag_qca.c:48:15: got restricted __be16 [usertype]
net/dsa/tag_qca.c:68:13: warning: incorrect type in assignment (different base types)
net/dsa/tag_qca.c:68:13: expected restricted __be16 [usertype] hdr
net/dsa/tag_qca.c:68:13: got int
net/dsa/tag_qca.c:71:16: warning: restricted __be16 degrades to integer
net/dsa/tag_qca.c:81:17: warning: restricted __be16 degrades to integer
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa/tag_mtk.c:84:13: warning: incorrect type in assignment (different base types)
net/dsa/tag_mtk.c:84:13: expected restricted __be16 [usertype] hdr
net/dsa/tag_mtk.c:84:13: got int
net/dsa/tag_mtk.c:94:17: warning: restricted __be16 degrades to integer
The result of a ntohs() is not __be16, but u16.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa/tag_lan9303.c:76:24: warning: incorrect type in assignment (different base types)
net/dsa/tag_lan9303.c:76:24: expected unsigned short [usertype]
net/dsa/tag_lan9303.c:76:24: got restricted __be16 [usertype]
net/dsa/tag_lan9303.c:80:24: warning: incorrect type in assignment (different base types)
net/dsa/tag_lan9303.c:80:24: expected unsigned short [usertype]
net/dsa/tag_lan9303.c:80:24: got restricted __be16 [usertype]
net/dsa/tag_lan9303.c:106:31: warning: restricted __be16 degrades to integer
net/dsa/tag_lan9303.c:111:24: warning: cast to restricted __be16
net/dsa/tag_lan9303.c:111:24: warning: cast to restricted __be16
net/dsa/tag_lan9303.c:111:24: warning: cast to restricted __be16
net/dsa/tag_lan9303.c:111:24: warning: cast to restricted __be16
Make use of __be16 where appropriate to fix these warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpu_to_be16 returns a __be16 value. So what it is assigned to needs to
have the same type to avoid warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa/slave.c:505:13: warning: incorrect type in initializer (different address spaces)
net/dsa/slave.c:505:13: expected void const [noderef] <asn:3> *__vpp_verify
net/dsa/slave.c:505:13: got struct pcpu_sw_netstats *
Add the needed _percpu property to prevent this warning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not very informative to know the DSA master device when a
subordinate network device fails to get its PHY setup. Provide the
device name and capitalize PHY while we are it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Marvell switches puts all ports in IGMP snooping mode
which results in all IGMP/MLD frames that ingress on the ports to be
forwarded to the CPU only.
The bridge code in the kernel can then interpret these frames and act
upon them, for instance by updating the mdb in the switch to reflect
multicast memberships of stations connected to the ports. However,
the IGMP/MLD frames must then also be forwarded to other ports of the
bridge so external IGMP queriers can track membership reports, and
external multicast clients can receive query reports from foreign IGMP
queriers.
Currently, this is impossible as the EDSA tagger sets offload_fwd_mark
on the skb when it unwraps the tagged frames, and that will make the
switchdev layer prevent the skb from egressing on any other port of
the same switch.
To fix that, look at the To_CPU code in the DSA header and make
forwarding of the frame possible for trapped IGMP packets.
Introduce some #defines for the frame types to make the code a bit more
comprehensive.
This was tested on a Marvell 88E6352 variant.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
The dynamic key update for addr_list_lock still causes troubles,
for example the following race condition still exists:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
dev_mc_seq_show() netdev_update_lockdep_key()
-> lockdep_unregister_key()
-> netif_addr_lock_bh()
because lockdep doesn't provide an API to update it atomically.
Therefore, we have to move it back to static keys and use subclass
for nest locking like before.
In commit 1a33e10e4a ("net: partially revert dynamic lockdep key
changes"), I already reverted most parts of commit ab92d68fc2
("net: core: add generic lockdep keys").
This patch reverts the rest and also part of commit f3b0a18bb6
("net: remove unnecessary variables and callback"). After this
patch, addr_list_lock changes back to using static keys and
subclasses to satisfy lockdep. Thanks to dev->lower_level, we do
not have to change back to ->ndo_get_lock_subclass().
And hopefully this reduces some syzbot lockdep noises too.
Reported-by: syzbot+f3a0e80c34b3fc28ac5e@syzkaller.appspotmail.com
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, our only tag_8021q user, sja1105, has the ability to restore
bridge VLANs on its own, so this logic is unnecessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be there a platform with the following layout:
Regular NIC
|
+----> DSA master for switch port
|
+----> DSA master for another switch port
After changing DSA back to static lockdep class keys in commit
1a33e10e4a ("net: partially revert dynamic lockdep key changes"), this
kernel splat can be seen:
[ 13.361198] ============================================
[ 13.366524] WARNING: possible recursive locking detected
[ 13.371851] 5.7.0-rc4-02121-gc32a05ecd7af-dirty #988 Not tainted
[ 13.377874] --------------------------------------------
[ 13.383201] swapper/0/0 is trying to acquire lock:
[ 13.388004] ffff0000668ff298 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[ 13.397879]
[ 13.397879] but task is already holding lock:
[ 13.403727] ffff0000661a1698 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[ 13.413593]
[ 13.413593] other info that might help us debug this:
[ 13.420140] Possible unsafe locking scenario:
[ 13.420140]
[ 13.426075] CPU0
[ 13.428523] ----
[ 13.430969] lock(&dsa_slave_netdev_xmit_lock_key);
[ 13.435946] lock(&dsa_slave_netdev_xmit_lock_key);
[ 13.440924]
[ 13.440924] *** DEADLOCK ***
[ 13.440924]
[ 13.446860] May be due to missing lock nesting notation
[ 13.446860]
[ 13.453668] 6 locks held by swapper/0/0:
[ 13.457598] #0: ffff800010003de0 ((&idev->mc_ifc_timer)){+.-.}-{0:0}, at: call_timer_fn+0x0/0x400
[ 13.466593] #1: ffffd4d3fb478700 (rcu_read_lock){....}-{1:2}, at: mld_sendpack+0x0/0x560
[ 13.474803] #2: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: ip6_finish_output2+0x64/0xb10
[ 13.483886] #3: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x6c/0xbe0
[ 13.492793] #4: ffff0000661a1698 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[ 13.503094] #5: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x6c/0xbe0
[ 13.512000]
[ 13.512000] stack backtrace:
[ 13.516369] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc4-02121-gc32a05ecd7af-dirty #988
[ 13.530421] Call trace:
[ 13.532871] dump_backtrace+0x0/0x1d8
[ 13.536539] show_stack+0x24/0x30
[ 13.539862] dump_stack+0xe8/0x150
[ 13.543271] __lock_acquire+0x1030/0x1678
[ 13.547290] lock_acquire+0xf8/0x458
[ 13.550873] _raw_spin_lock+0x44/0x58
[ 13.554543] __dev_queue_xmit+0x84c/0xbe0
[ 13.558562] dev_queue_xmit+0x24/0x30
[ 13.562232] dsa_slave_xmit+0xe0/0x128
[ 13.565988] dev_hard_start_xmit+0xf4/0x448
[ 13.570182] __dev_queue_xmit+0x808/0xbe0
[ 13.574200] dev_queue_xmit+0x24/0x30
[ 13.577869] neigh_resolve_output+0x15c/0x220
[ 13.582237] ip6_finish_output2+0x244/0xb10
[ 13.586430] __ip6_finish_output+0x1dc/0x298
[ 13.590709] ip6_output+0x84/0x358
[ 13.594116] mld_sendpack+0x2bc/0x560
[ 13.597786] mld_ifc_timer_expire+0x210/0x390
[ 13.602153] call_timer_fn+0xcc/0x400
[ 13.605822] run_timer_softirq+0x588/0x6e0
[ 13.609927] __do_softirq+0x118/0x590
[ 13.613597] irq_exit+0x13c/0x148
[ 13.616918] __handle_domain_irq+0x6c/0xc0
[ 13.621023] gic_handle_irq+0x6c/0x160
[ 13.624779] el1_irq+0xbc/0x180
[ 13.627927] cpuidle_enter_state+0xb4/0x4d0
[ 13.632120] cpuidle_enter+0x3c/0x50
[ 13.635703] call_cpuidle+0x44/0x78
[ 13.639199] do_idle+0x228/0x2c8
[ 13.642433] cpu_startup_entry+0x2c/0x48
[ 13.646363] rest_init+0x1ac/0x280
[ 13.649773] arch_call_rest_init+0x14/0x1c
[ 13.653878] start_kernel+0x490/0x4bc
Lockdep keys themselves were added in commit ab92d68fc2 ("net: core:
add generic lockdep keys"), and it's very likely that this splat existed
since then, but I have no real way to check, since this stacked platform
wasn't supported by mainline back then.
>From Taehee's own words:
This patch was considered that all stackable devices have LLTX flag.
But the dsa doesn't have LLTX, so this splat happened.
After this patch, dsa shares the same lockdep class key.
On the nested dsa interface architecture, which you illustrated,
the same lockdep class key will be used in __dev_queue_xmit() because
dsa doesn't have LLTX.
So that lockdep detects deadlock because the same lockdep class key is
used recursively although actually the different locks are used.
There are some ways to fix this problem.
1. using NETIF_F_LLTX flag.
If possible, using the LLTX flag is a very clear way for it.
But I'm so sorry I don't know whether the dsa could have LLTX or not.
2. using dynamic lockdep again.
It means that each interface uses a separate lockdep class key.
So, lockdep will not detect recursive locking.
But this way has a problem that it could consume lockdep class key
too many.
Currently, lockdep can have 8192 lockdep class keys.
- you can see this number with the following command.
cat /proc/lockdep_stats
lock-classes: 1251 [max: 8192]
...
The [max: 8192] means that the maximum number of lockdep class keys.
If too many lockdep class keys are registered, lockdep stops to work.
So, using a dynamic(separated) lockdep class key should be considered
carefully.
In addition, updating lockdep class key routine might have to be existing.
(lockdep_register_key(), lockdep_set_class(), lockdep_unregister_key())
3. Using lockdep subclass.
A lockdep class key could have 8 subclasses.
The different subclass is considered different locks by lockdep
infrastructure.
But "lock-classes" is not counted by subclasses.
So, it could avoid stopping lockdep infrastructure by an overflow of
lockdep class keys.
This approach should also have an updating lockdep class key routine.
(lockdep_set_subclass())
4. Using nonvalidate lockdep class key.
The lockdep infrastructure supports nonvalidate lockdep class key type.
It means this lockdep is not validated by lockdep infrastructure.
So, the splat will not happen but lockdep couldn't detect real deadlock
case because lockdep really doesn't validate it.
I think this should be used for really special cases.
(lockdep_set_novalidate_class())
Further discussion here:
https://patchwork.ozlabs.org/project/netdev/patch/20200503052220.4536-2-xiyou.wangcong@gmail.com/
There appears to be no negative side-effect to declaring lockless TX for
the DSA virtual interfaces, which means they handle their own locking.
So that's what we do to make the splat go away.
Patch tested in a wide variety of cases: unicast, multicast, PTP, etc.
Fixes: ab92d68fc2 ("net: core: add generic lockdep keys")
Suggested-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A comparison between a value from the packet and an integer constant
value needs to be done by converting the value from the packet from
net->host, or the constant from host->net. Not the other way around.
Even though it makes no practical difference, correct that.
Fixes: 38b5beeae7 ("net: dsa: sja1105: prepare tagger for handling DSA tags and VLAN simultaneously")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a subvlan_map as part of each port's tagger private structure.
This keeps reverse mappings of bridge-to-dsa_8021q VLAN retagging rules.
Note that as of this patch, this piece of code is never engaged, due to
the fact that the driver hasn't installed any retagging rule, so we'll
always see packets with a subvlan code of 0 (untagged).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For switches that support VLAN retagging, such as sja1105, we extend
dsa_8021q by encoding a "sub-VLAN" into the remaining 3 free bits in the
dsa_8021q tag.
A sub-VLAN is nothing more than a number in the range 0-7, which serves
as an index into a per-port driver lookup table. The sub-VLAN value of
zero means that traffic is untagged (this is also backwards-compatible
with dsa_8021q without retagging).
The switch should be configured to retag VLAN-tagged traffic that gets
transmitted towards the CPU port (and towards the CPU only). Example:
bridge vlan add dev sw1p0 vid 100
The switch retags frames received on port 0, going to the CPU, and
having VID 100, to the VID of 1104 (0x0450). In dsa_8021q language:
| 11 | 10 | 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
+-----------+-----+-----------------+-----------+-----------------------+
| DIR | SVL | SWITCH_ID | SUBVLAN | PORT |
+-----------+-----+-----------------+-----------+-----------------------+
0x0450 means:
- DIR = 0b01: this is an RX VLAN
- SUBVLAN = 0b001: this is subvlan #1
- SWITCH_ID = 0b001: this is switch 1 (see the name "sw1p0")
- PORT = 0b0000: this is port 0 (see the name "sw1p0")
The driver also remembers the "1 -> 100" mapping. In the hotpath, if the
sub-VLAN from the tag encodes a non-untagged frame, this mapping is used
to create a VLAN hwaccel tag, with the value of 100.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In VLAN-unaware mode, sja1105 uses VLAN tags with a custom TPID of
0xdadb. While in the yet-to-be introduced best_effort_vlan_filtering
mode, it needs to work with normal VLAN TPID values.
A complication arises when we must transmit a VLAN-tagged packet to the
switch when it's in VLAN-aware mode. We need to construct a packet with
2 VLAN tags, and the switch will use the outer header for routing and
pop it on egress. But sadly, here the 2 hardware generations don't
behave the same:
- E/T switches won't pop an ETH_P_8021AD tag on egress, it seems
(packets will remain double-tagged).
- P/Q/R/S switches will drop a packet with 2 ETH_P_8021Q tags (it looks
like it tries to prevent VLAN hopping).
But looks like the reverse is also true:
- E/T switches have no problem popping the outer tag from packets with
2 ETH_P_8021Q tags.
- P/Q/R/S will have no problem popping a single tag even if that is
ETH_P_8021AD.
So it is clear that if we want the hardware to work with dsa_8021q
tagging in VLAN-aware mode, we need to send different TPIDs depending on
revision. Keep that information in priv->info->qinq_tpid.
The per-port tagger structure will hold an xmit_tpid value that depends
not only upon the qinq_tpid, but also upon the VLAN awareness state
itself (in case we must transmit using 0xdadb).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Managing the VLAN table that is present in hardware will become very
difficult once we add a third operating state
(best_effort_vlan_filtering). That is because correct cleanup (not too
little, not too much) becomes virtually impossible, when VLANs can be
added from the bridge layer, from dsa_8021q for basic tagging, for
cross-chip bridging, as well as retagging rules for sub-VLANs and
cross-chip sub-VLANs. So we need to rethink VLAN interaction with the
switch in a more scalable way.
In preparation for that, use the priv->expect_dsa_8021q boolean to
classify any VLAN request received through .port_vlan_add or
.port_vlan_del towards either one of 2 internal lists: bridge VLANs and
dsa_8021q VLANs.
Then, implement a central sja1105_build_vlan_table method that creates a
VLAN configuration from scratch based on the 2 lists of VLANs kept by
the driver, and based on the VLAN awareness state. Currently, if we are
VLAN-unaware, install the dsa_8021q VLANs, otherwise the bridge VLANs.
Then, implement a delta commit procedure that identifies which VLANs
from this new configuration are actually different from the config
previously committed to hardware. We apply the delta through the dynamic
configuration interface (we don't reset the switch). The result is that
the hardware should see the exact sequence of operations as before this
patch.
This also helps remove the "br" argument passed to
dsa_8021q_crosschip_bridge_join, which it was only using to figure out
whether it should commit the configuration back to us or not, based on
the VLAN awareness state of the bridge. We can simplify that, by always
allowing those VLANs inside of our dsa_8021q_vlans list, and committing
those to hardware when necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function returns a boolean denoting whether the VLAN passed as
argument is part of the 1024-3071 range that the dsa_8021q tagging
scheme uses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA assumes that a bridge which has vlan filtering disabled is not
vlan aware, and ignores all vlan configuration. However, the kernel
software bridge code allows configuration in this state.
This causes the kernel's idea of the bridge vlan state and the
hardware state to disagree, so "bridge vlan show" indicates a correct
configuration but the hardware lacks all configuration. Even worse,
enabling vlan filtering on a DSA bridge immediately blocks all traffic
which, given the output of "bridge vlan show", is very confusing.
Provide an option that drivers can set to indicate they want to receive
vlan configuration even when vlan filtering is disabled. At the very
least, this is safe for Marvell DSA bridges, which do not look up
ingress traffic in the VTU if the port is in 8021Q disabled state. It is
also safe for the Ocelot switch family. Whether this change is suitable
for all DSA bridges is not known.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sja1105_netdev_ops should be const since that is what the DSA layer
expects.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_netdev_ops should be const since that is what the DSA layer
expects.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sja1105 uses dsa_8021q for DSA tagging, a format which is VLAN at heart
and which is compatible with cascading. A complete description of this
tagging format is in net/dsa/tag_8021q.c, but a quick summary is that
each external-facing port tags incoming frames with a unique pvid, and
this special VLAN is transmitted as tagged towards the inside of the
system, and as untagged towards the exterior. The tag encodes the switch
id and the source port index.
This means that cross-chip bridging for dsa_8021q only entails adding
the dsa_8021q pvids of one switch to the RX filter of the other
switches. Everything else falls naturally into place, as long as the
bottom-end of ports (the leaves in the tree) is comprised exclusively of
dsa_8021q-compatible (i.e. sja1105 switches). Otherwise, there would be
a chance that a front-panel switch transmits a packet tagged with a
dsa_8021q header, header which it wouldn't be able to remove, and which
would hence "leak" out.
The only use case I tested (due to lack of board availability) was when
the sja1105 switches are part of disjoint trees (however, this doesn't
change the fact that multiple sja1105 switches still need unique switch
identifiers in such a system). But in principle, even "true" single-tree
setups (with DSA links) should work just as fine, except for a small
change which I can't test: dsa_towards_port should be used instead of
dsa_upstream_port (I made the assumption that the routing port that any
sja1105 should use towards its neighbours is the CPU port. That might
not hold true in other setups).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Somewhat similar to dsa_tree_find, dsa_switch_find returns a dsa_switch
structure pointer by searching for its tree index and switch index (the
parameters from dsa,member). To be used, for example, by drivers who
implement .crosschip_bridge_join and need a reference to the other
switch indicated to by the tree_index and sw_index arguments.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netpoll_send_skb() callers seem to leak skb if
the np pointer is NULL. While this should not happen, we
can make the code more robust.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have a trailing newline.
Add a cocci script which catches cases where the newline marker is
present. Using this script, fix the handful of cases which accidentally
included a trailing new line.
I couldn't figure out a way to get a patch mode working, so this script
only implements context, report, and org.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As its implementation shows, this is synonimous with calling
dsa_slave_dev_check followed by dsa_slave_to_port, so it is quite simple
already and provides functionality which is already there.
However there is now a need for these functions outside dsa_priv.h, for
example in drivers that perform mirroring and redirection through
tc-flower offloads (they are given raw access to the flow_cls_offload
structure), where they need to call this function on act->dev.
But simply exporting dsa_slave_to_port would make it non-inline and
would result in an extra function call in the hotpath, as can be seen
for example in sja1105:
Before:
000006dc <sja1105_xmit>:
{
6dc: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e0: e1a04000 mov r4, r0
6e4: e591958c ldr r9, [r1, #1420] ; 0x58c <- Inline dsa_slave_to_port
6e8: e1a05001 mov r5, r1
6ec: e24dd004 sub sp, sp, #4
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6f0: e1c901d8 ldrd r0, [r9, #24]
6f4: ebfffffe bl 0 <dsa_8021q_tx_vid>
6f4: R_ARM_CALL dsa_8021q_tx_vid
u8 pcp = netdev_txq_to_tc(netdev, queue_mapping);
6f8: e1d416b0 ldrh r1, [r4, #96] ; 0x60
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
6fc: e1a08000 mov r8, r0
After:
000006e4 <sja1105_xmit>:
{
6e4: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr}
6e8: e1a04000 mov r4, r0
6ec: e24dd004 sub sp, sp, #4
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f0: e1a00001 mov r0, r1
{
6f4: e1a05001 mov r5, r1
struct dsa_port *dp = dsa_slave_to_port(netdev);
6f8: ebfffffe bl 0 <dsa_slave_to_port>
6f8: R_ARM_CALL dsa_slave_to_port
6fc: e1a09000 mov r9, r0
u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index);
700: e1c001d8 ldrd r0, [r0, #24]
704: ebfffffe bl 0 <dsa_8021q_tx_vid>
704: R_ARM_CALL dsa_8021q_tx_vid
Because we want to avoid possible performance regressions, introduce
this new function which is designed to be public.
Suggested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ndo_get_phys_port_name() for the CPU port was added we introduced
an early check for when the DSA master network device in
dsa_master_ndo_setup() already implements ndo_get_phys_port_name(). When
we perform the teardown operation in dsa_master_ndo_teardown() we would
not be checking that cpu_dp->orig_ndo_ops was successfully allocated and
non-NULL initialized.
With network device drivers such as virtio_net, this leads to a NPD as
soon as the DSA switch hanging off of it gets torn down because we are
now assigning the virtio_net device's netdev_ops a NULL pointer.
Fixes: da7b9e9b00 ("net: dsa: Add ndo_get_phys_port_name() for CPU port")
Reported-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was caused by a poor merge conflict resolution on my side. The
"act = &cls->rule->action.entries[0];" assignment was already present in
the code prior to the patch mentioned below.
Fixes: e13c207528 ("net: dsa: refactor matchall mirred action to separate function")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts the folowing commits:
commit 064ff66e2b
"bonding: add missing netdev_update_lockdep_key()"
commit 53d374979e
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit 1f26c0d3d2
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit ab92d68fc2
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 1d27732f41 ("net: dsa: setup and teardown ports"), we would
not treat failures to set-up an user port as fatal, but after this
commit we would, which is a regression for some systems where interfaces
may be declared in the Device Tree, but the underlying hardware may not
be present (pluggable daughter cards for instance).
Fixes: 1d27732f41 ("net: dsa: setup and teardown ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the callback into the phylink_config structure, rather than
providing a callback to set this up.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort of "encapsulation", and we can use the same mechs to
greatly improve overall DSA performance.
skbs are passed to the GRO layer after removing CPU tags, so we don't
need any new packet offload types as it was firstly proposed by me in
the first GRO-over-DSA variant [1].
The size of struct gro_cells is sizeof(void *), so hot struct
dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields
remain in one 32-byte cacheline.
The other positive side effect is that drivers for network devices
that can be shipped as CPU ports of DSA-driven switches can now use
napi_gro_frags() to pass skbs to kernel. Packets built that way are
completely non-linear and are likely being dropped without GRO.
This was tested on to-be-mainlined-soon Ethernet driver that uses
napi_gro_frags(), and the overall performance was on par with the
variant from [1], sometimes even better due to minimal overhead.
net.core.gro_normal_batch tuning may help to push it to the limit
on particular setups and platforms.
iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup
on 1.2 GHz MIPS board:
5.7-rc2 baseline:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender
[ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver
Iface RX packets TX packets
eth0 7097731 7097702
port0 426050 6671829
port1 6671681 425862
port1.218 6671677 425851
With this patch:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender
[ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver
Iface RX packets TX packets
eth0 9474792 9474777
port0 455200 353288
port1 9019592 455035
port1.218 353144 455024
v2:
- Add some performance examples in the commit message;
- No functional changes.
[1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/
Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to fail the probing of the switch if the MTU couldn't
be configured correctly (either the switch port itself, or the host
port) for whatever reason. MTU-sized traffic probably won't work, sure,
but we can still probably limp on and support some form of communication
anyway, which the users would probably appreciate more.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA and CPU ports can be configured in two ways. By default, the
driver should configure such ports to there maximum bandwidth. For
most use cases, this is sufficient. When this default is insufficient,
a phylink instance can be bound to such ports, and phylink will
configure the port, e.g. based on fixed-link properties. phylink
assumes the port is initially down. Given that the driver should have
already configured it to its maximum speed, ask the driver to down
the port before instantiating the phylink instance.
Fixes: 30c4a5b0aa ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: f41071407c85 ("net: dsa: implement auto-normalization of MTU for bridge hardware datapath")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an oops in dsa_port_phylink_mac_change() caused by a combination
of a20f997010 ("net: dsa: Don't instantiate phylink for CPU/DSA
ports unless needed") and the net-dsa-improve-serdes-integration
series of patches 65b7a2c8e3 ("Merge branch
'net-dsa-improve-serdes-integration'").
Unable to handle kernel NULL pointer dereference at virtual address 00000124
pgd = c0004000
[00000124] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: tag_edsa spi_nor mtd xhci_plat_hcd mv88e6xxx(+) xhci_hcd armada_thermal marvell_cesa dsa_core ehci_orion libdes phy_armada38x_comphy at24 mcp3021 sfp evbug spi_orion sff mdio_i2c
CPU: 1 PID: 214 Comm: irq/55-mv88e6xx Not tainted 5.6.0+ #470
Hardware name: Marvell Armada 380/385 (Device Tree)
PC is at phylink_mac_change+0x10/0x88
LR is at mv88e6352_serdes_irq_status+0x74/0x94 [mv88e6xxx]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The approach taken to pass the port policer methods on to drivers is
pragmatic. It is similar to the port mirroring implementation (in that
the DSA core does all of the filter block interaction and only passes
simple operations for the driver to implement) and dissimilar to how
flow-based policers are going to be implemented (where the driver has
full control over the flow_cls_offload data structure).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make room for other actions for the matchall filter by keeping the
mirred argument parsing self-contained in its own function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in preparing the module name in a buffer. The format
string can be passed diectly to 'request_module()'.
This axes a few lines of code and cleans a few things:
- max len for a driver name is MODULE_NAME_LEN wich is ~ 60 chars,
not 128. It would be down-sized in 'request_module()'
- we should pass the total size of the buffer to 'snprintf()', not the
size minus 1
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: d461933638 ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a flow_dissect callback which returns the network offset and
where to find the skb protocol, given the tags structure a common
function works for both tagging formats that are supported.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5037d532b8 ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue a warning to the kernel log if phylink_mac_link_state() returns
an error. This should not occur, but let's make it visible.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, DSA drivers should configure CPU and DSA ports to their
maximum speed. In many configurations this is sufficient to make the
link work.
In some cases it is necessary to configure the link to run slower,
e.g. because of limitations of the SoC it is connected to. Or back to
back PHYs are used and the PHY needs to be driven in order to
establish link. In this case, phylink is used.
Only instantiate phylink if it is required. If there is no PHY, or no
fixed link properties, phylink can upset a link which works in the
default configuration.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the immense variety of classification keys and actions available
for tc-flower, as well as due to potentially very different DSA switch
capabilities, it doesn't make a lot of sense for the DSA mid layer to
even attempt to interpret these. So just pass them on to the underlying
switch driver.
DSA implements just the standard boilerplate for binding and unbinding
flow blocks to ports, since nobody wants to deal with that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place phylink_start()/phylink_stop() inside dsa_port_enable() and
dsa_port_disable(), which ensures that we call phylink_stop() before
tearing down phylink - which is a documented requirement. Failure
to do so can cause use-after-free bugs.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA sets up a switch tree little by little. Every switch of the N
members of the tree calls dsa_register_switch, and (N - 1) will just
touch the dst->ports list with their ports and quickly exit. Only the
last switch that calls dsa_register_switch will find all DSA links
complete in dsa_tree_setup_routing_table, and not return zero as a
result but instead go ahead and set up the entire DSA switch tree
(practically on behalf of the other switches too).
The trouble is that the (N - 1) switches don't clean up after themselves
after they get an error such as EPROBE_DEFER. Their footprint left in
dst->ports by dsa_switch_touch_ports is still there. And switch N, the
one responsible with actually setting up the tree, is going to work with
those stale dp, dp->ds and dp->ds->dev pointers. In particular ds and
ds->dev might get freed by the device driver.
Be there a 2-switch tree and the following calling order:
- Switch 1 calls dsa_register_switch
- Calls dsa_switch_touch_ports, populates dst->ports
- Calls dsa_port_parse_cpu, gets -EPROBE_DEFER, exits.
- Switch 2 calls dsa_register_switch
- Calls dsa_switch_touch_ports, populates dst->ports
- Probe doesn't get deferred, so it goes ahead.
- Calls dsa_tree_setup_routing_table, which returns "complete == true"
due to Switch 1 having called dsa_switch_touch_ports before.
- Because the DSA links are complete, it calls dsa_tree_setup_switches
now.
- dsa_tree_setup_switches iterates through dst->ports, initializing
the Switch 1 ds structure (invalid) and the Switch 2 ds structure
(valid).
- Undefined behavior (use after free, sometimes NULL pointers, etc).
Real example below (debugging prints added by me, as well as guards
against NULL pointers):
[ 5.477947] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.313002] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.319932] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.329693] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.339458] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.349226] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.358991] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.368758] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.378524] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.388291] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.398057] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.407912] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.417682] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.427446] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.437212] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.446979] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.456744] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.466512] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.476277] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.486043] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.495810] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.505577] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.515433] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.354120] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.361045] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.370805] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.380571] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.390337] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.400104] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.409872] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.419637] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.429403] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.439169] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803db15b80 (dev ffffff803d8e4800)
The solution is to recognize that the functions that call
dsa_switch_touch_ports (dsa_switch_parse_of, dsa_switch_parse) have side
effects, and therefore one should clean up their side effects on error
path. The cleanup of dst->ports was taken from dsa_switch_remove and
moved into a dedicated dsa_switch_release_ports function, which should
really be per-switch (free only the members of dst->ports that are also
members of ds, instead of all switch ports).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA subsystem takes care of netdev statistics since commit 4ed70ce9f0
("net: dsa: Refactor transmit path to eliminate duplication"), so
any accounting inside tagger callbacks is redundant and can lead to
messing up the stats.
This bug is present in Qualcomm tagger since day 0.
Fixes: cafdc45c94 ("net-next: dsa: add Qualcomm tag RX/TX handler")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name is GSWIP (Gigabit Switch IP). Typo was introduced in
875138f81d ("dsa: Move tagger name into its ops structure") while
moving tagger names to their structures.
Fixes: 875138f81d ("dsa: Move tagger name into its ops structure")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA drivers that implement .phylink_mac_link_state should normally
register an interrupt for the PCS, from which they should call
phylink_mac_change(). However not all switches implement this, and those
who don't should set this flag in dsa_switch in the .setup callback, so
that PHYLINK will poll for a few ms until the in-band AN link timer
expires and the PCS state settles.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that makes the dp, tx_vid, queue_mapping and
pcp local variable definitions a bit closer in length, so they don't
look like an eyesore as much.
The 'ds' variable is not used otherwise, except for ds->dp.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to kill PTP on a DSA switch completely and absolutely,
until a reboot, with a simple command:
tcpdump -i eth2 -j adapter_unsynced
where eth2 is the switch's DSA master.
Why? Well, in short, the PTP API in place today is a bit rudimentary and
relies on applications to retrieve the TX timestamps by polling the
error queue and looking at the cmsg structure. But there is no timestamp
identification of any sorts (except whether it's HW or SW), you don't
know how many more timestamps are there to come, which one is this one,
from whom it is, etc. In other words, the SO_TIMESTAMPING API is
fundamentally limited in that you can get a single HW timestamp from the
stack.
And the "-j adapter_unsynced" flag of tcpdump enables hardware
timestamping.
So let's imagine what happens when the DSA master decides it wants to
deliver TX timestamps to the skb's socket too:
- The timestamp that the user space sees is taken by the DSA master.
Whereas the RX timestamp will eventually be overwritten by the DSA
switch. So the RX and TX timestamps will be in different time bases
(aka garbage).
- The user space applications have no way to deal with the second (real)
TX timestamp finally delivered by the DSA switch, or even to know to
wait for it.
Take ptp4l from the linuxptp project, for example. This is its behavior
after running tcpdump, before the patch:
ptp4l[172]: [6469.594] Unexpected data on socket err queue:
ptp4l[172]: [6469.693] rms 8 max 16 freq -21257 +/- 11 delay 748 +/- 0
ptp4l[172]: [6469.711] Unexpected data on socket err queue:
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 05 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.721] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b1 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.838] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 06 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.848] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 13 02
ptp4l[172]: 0010 00 36 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 04 1a 45 05 7f
ptp4l[172]: 0030 00 00 5e 05 41 32 27 c2 1a 68 00 04 9f ff fe 05
ptp4l[172]: 0040 de 06 00 01
ptp4l[172]: [6469.855] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b2 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.974] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 07 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
The ptp4l program itself is heavily patched to show this (more details
here [0]). Otherwise, by default it just hangs.
On the other hand, with the DSA patch to disallow HW timestamping
applied:
tcpdump -i eth2 -j adapter_unsynced
tcpdump: SIOCSHWTSTAMP failed: Device or resource busy
So it is a fact of life that PTP timestamping on the DSA master is
incompatible with timestamping on the switch MAC, at least with the
current API. And if the switch supports PTP, taking the timestamps from
the switch MAC is highly preferable anyway, due to the fact that those
don't contain the queuing latencies of the switch. So just disallow PTP
on the DSA master if there is any PTP-capable switch attached.
[0]: https://sourceforge.net/p/linuxptp/mailman/message/36880648/
Fixes: 0336369d3a ("net: dsa: forward hardware timestamping ioctls to switch driver")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove special taglen define KSZ8795_INGRESS_TAG_LEN
and use generic KSZ_INGRESS_TAG_LEN instead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tag format used in Atheros AR9331 built-in switch.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_link_touch() is not exported, or defined outside of the
file it is in so make it static to avoid the following warning:
net/dsa/dsa2.c:127:17: warning: symbol 'dsa_link_touch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77373d49de ("net: dsa: Move the phylink driver calls into
port.c") moved and exported a bunch of symbols, but they are not used
outside of net/dsa/port.c at the moment, so no reason to export them.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sequence of operations:
ip link set dev br0 type bridge vlan_filtering 1
bridge vlan del dev swp2 vid 1
ip link set dev br0 type bridge vlan_filtering 1
ip link set dev br0 type bridge vlan_filtering 0
apparently fails with the message:
[ 31.305716] sja1105 spi0.1: Reset switch and programmed static config. Reason: VLAN filtering
[ 31.322161] sja1105 spi0.1: Couldn't determine PVID attributes (pvid 0)
[ 31.328939] sja1105 spi0.1: Failed to setup VLAN tagging for port 1: -2
[ 31.335599] ------------[ cut here ]------------
[ 31.340215] WARNING: CPU: 1 PID: 194 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 31.349981] br0: Commit of attribute (id=6) failed.
[ 31.354890] Modules linked in:
[ 31.357942] CPU: 1 PID: 194 Comm: ip Not tainted 5.4.0-rc6-01792-gf4f632e07665-dirty #2062
[ 31.366167] Hardware name: Freescale LS1021A
[ 31.370437] [<c03144dc>] (unwind_backtrace) from [<c030e184>] (show_stack+0x10/0x14)
[ 31.378153] [<c030e184>] (show_stack) from [<c11d1c1c>] (dump_stack+0xe0/0x10c)
[ 31.385437] [<c11d1c1c>] (dump_stack) from [<c034c730>] (__warn+0xf4/0x10c)
[ 31.392373] [<c034c730>] (__warn) from [<c034c7bc>] (warn_slowpath_fmt+0x74/0xb8)
[ 31.399827] [<c034c7bc>] (warn_slowpath_fmt) from [<c11ca204>] (switchdev_port_attr_set_now+0x9c/0xa4)
[ 31.409097] [<c11ca204>] (switchdev_port_attr_set_now) from [<c117036c>] (__br_vlan_filter_toggle+0x6c/0x118)
[ 31.418971] [<c117036c>] (__br_vlan_filter_toggle) from [<c115d010>] (br_changelink+0xf8/0x518)
[ 31.427637] [<c115d010>] (br_changelink) from [<c0f8e9ec>] (__rtnl_newlink+0x3f4/0x76c)
[ 31.435613] [<c0f8e9ec>] (__rtnl_newlink) from [<c0f8eda8>] (rtnl_newlink+0x44/0x60)
[ 31.443329] [<c0f8eda8>] (rtnl_newlink) from [<c0f89f20>] (rtnetlink_rcv_msg+0x2cc/0x51c)
[ 31.451477] [<c0f89f20>] (rtnetlink_rcv_msg) from [<c1008df8>] (netlink_rcv_skb+0xb8/0x110)
[ 31.459796] [<c1008df8>] (netlink_rcv_skb) from [<c1008648>] (netlink_unicast+0x17c/0x1f8)
[ 31.468026] [<c1008648>] (netlink_unicast) from [<c1008980>] (netlink_sendmsg+0x2bc/0x3b4)
[ 31.476261] [<c1008980>] (netlink_sendmsg) from [<c0f43858>] (___sys_sendmsg+0x230/0x250)
[ 31.484408] [<c0f43858>] (___sys_sendmsg) from [<c0f44c84>] (__sys_sendmsg+0x50/0x8c)
[ 31.492209] [<c0f44c84>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x28)
[ 31.500090] Exception stack(0xedf47fa8 to 0xedf47ff0)
[ 31.505122] 7fa0: 00000002 b6f2e060 00000003 beabd6a4 00000000 00000000
[ 31.513265] 7fc0: 00000002 b6f2e060 5d6e3213 00000128 00000000 00000001 00000006 000619c4
[ 31.521405] 7fe0: 00086078 beabd658 0005edbc b6e7ce68
The reason is the implementation of br_get_pvid:
static inline u16 br_get_pvid(const struct net_bridge_vlan_group *vg)
{
if (!vg)
return 0;
smp_rmb();
return vg->pvid;
}
Since VID 0 is an invalid pvid from the bridge's point of view, let's
add this check in dsa_8021q_restore_pvid to avoid restoring a pvid that
doesn't really exist.
Fixes: 5f33183b7f ("net: dsa: tag_8021q: Restore bridge VLANs when enabling vlan_filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.
The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.
The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a switch driver to use NET_DSA_TAG_8021Q as a valid
DSA tagging protocol since it registers itself as such, unfortunately
since there are not xmit or rcv functions provided, the lack of a xmit()
function will lead to a NPD in dsa_slave_xmit() to start with.
net/dsa/tag_8021q.c is only comprised of a set of helper functions at
the moment, but is not a fully autonomous or functional tagging "driver"
(though it could become later on). We do not have any users of
NET_DSA_TAG_8021Q so now is a good time to make sure there are not
issues being encountered by making this file strictly a place holder for
helper functions.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wrappers around the devlink resource API, so that DSA drivers can
register and unregister devlink resources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which the ports are deleted from the list and freed and the
call to dsa_switch_remove() is done is reversed, which leads to an
use after free condition. Reverse the two: first tear down the ports and
switch from the fabric, then free the ports associated with that switch
fabric.
Fixes: 05f294a852 ("net: dsa: allocate ports on touch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there's no restriction from the DSA core side regarding
the switch IDs and port numbers, only tag_8021q which is currently
reserving 3 bits for the switch ID and 4 bits for the port number, has
limitation for these values. Update their descriptions to reflect that.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because there is no static array describing the links between switches
anymore, we have no reason to force a limitation of the index value
set by the device tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA fabric setup code has been simplified a lot so get rid of
the dsa_tree_remove_switch, dsa_tree_add_switch and dsa_switch_add
helpers, and keep the code simple with only the dsa_switch_probe and
dsa_switch_remove functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA ports are listed in the switch fabric, there is
no need to store the dsa_switch structures from the drivers in the
fabric anymore. So get rid of the dst->ds static array.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure has no routing table specific data to setup,
so the switch fabric can directly walk its ports and initialize its
routing table from them.
This allows us to remove the dsa_switch_setup_routing_table function.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not use the ds->rtable static arrays anymore, get rid of it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue logic to make pause settings per port
configurable vie ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add plumbing to allow DSA drivers to register parameters with devlink.
To keep with the abstraction, the DSA drivers pass the ds structure to
these helpers, and the DSA core then translates that to the devlink
structure associated to the device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ds->dev is dereferenced on the assignments of pdata and
np before ds->dev is null checked, hence there is a potential null
pointer dereference on ds->dev. Fix this by assigning pdata and
np after the ds->dev null pointer sanity check.
Addresses-Coverity: ("Dereference before null check")
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Allocate the struct dsa_port the first time it is accessed with
dsa_port_touch, and remove the static dsa_port array from the
dsa_switch structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the default CPU port. Unassign it on teardown.
Now that we can iterate over multiple CPU ports, remove dst->cpu_dp.
At the same time, provide a better error message for CPU-less tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when looking up the first CPU port in the tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Now that we have a potential list of CPU ports, make use of it instead
of only configuring the master device of an unique CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports to find a port from a given node.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of accessing the dsa_switch array
of ports when iterating over DSA ports of a switch to set up the
routing table.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the switches and their ports.
At the same time, provide setup states and messages for ports and
switches as it is done for the trees.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when looking for a slave device from a given master interface.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add a list of switch ports within the switch fabric. This will help the
lookup of a port inside the whole fabric, and it is the first step
towards supporting multiple CPU ports, before deprecating the usage of
the unique dst->cpu_dp pointer.
In preparation for a future allocation of the dsa_port structures,
return -ENOMEM in case no structure is returned, even though this
error cannot be reached yet.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this stack trace can be seen with CONFIG_DEBUG_ATOMIC_SLEEP=y:
[ 41.568348] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:909
[ 41.576757] in_atomic(): 1, irqs_disabled(): 0, pid: 208, name: ptp4l
[ 41.583212] INFO: lockdep is turned off.
[ 41.587123] CPU: 1 PID: 208 Comm: ptp4l Not tainted 5.3.0-rc6-01445-ge950f2d4bc7f-dirty #1827
[ 41.599873] [<c0313d7c>] (unwind_backtrace) from [<c030e13c>] (show_stack+0x10/0x14)
[ 41.607584] [<c030e13c>] (show_stack) from [<c1212d50>] (dump_stack+0xd4/0x100)
[ 41.614863] [<c1212d50>] (dump_stack) from [<c037dfc8>] (___might_sleep+0x1c8/0x2b4)
[ 41.622574] [<c037dfc8>] (___might_sleep) from [<c122ea90>] (__mutex_lock+0x48/0xab8)
[ 41.630368] [<c122ea90>] (__mutex_lock) from [<c122f51c>] (mutex_lock_nested+0x1c/0x24)
[ 41.638340] [<c122f51c>] (mutex_lock_nested) from [<c0c6fe08>] (sja1105_static_config_reload+0x30/0x27c)
[ 41.647779] [<c0c6fe08>] (sja1105_static_config_reload) from [<c0c7015c>] (sja1105_hwtstamp_set+0x108/0x1cc)
[ 41.657562] [<c0c7015c>] (sja1105_hwtstamp_set) from [<c0feb650>] (dev_ifsioc+0x18c/0x330)
[ 41.665788] [<c0feb650>] (dev_ifsioc) from [<c0febbd8>] (dev_ioctl+0x320/0x6e8)
[ 41.673064] [<c0febbd8>] (dev_ioctl) from [<c0f8b1f4>] (sock_ioctl+0x334/0x5e8)
[ 41.680340] [<c0f8b1f4>] (sock_ioctl) from [<c05404a8>] (do_vfs_ioctl+0xb0/0xa10)
[ 41.687789] [<c05404a8>] (do_vfs_ioctl) from [<c0540e3c>] (ksys_ioctl+0x34/0x58)
[ 41.695151] [<c0540e3c>] (ksys_ioctl) from [<c0301000>] (ret_fast_syscall+0x0/0x28)
[ 41.702768] Exception stack(0xe8495fa8 to 0xe8495ff0)
[ 41.707796] 5fa0: beff4a8c 00000001 00000011 000089b0 beff4a8c beff4a80
[ 41.715933] 5fc0: beff4a8c 00000001 0000000c 00000036 b6fa98c8 004e19c1 00000001 00000000
[ 41.724069] 5fe0: 004dcedc beff4a6c 004c0738 b6e7af4c
[ 41.729860] BUG: scheduling while atomic: ptp4l/208/0x00000002
[ 41.735682] INFO: lockdep is turned off.
Enabling RX timestamping will logically disturb the fastpath (processing
of meta frames). Replace bool hwts_rx_en with a bit that is checked
atomically from the fastpath and temporarily unset from the sleepable
context during a change of the RX timestamping process (a destructive
operation anyways, requires switch reset).
If found unset, the fastpath (net/dsa/tag_sja1105.c) will just drop any
received meta frame and not take the meta_lock at all.
Fixes: a602afd200 ("net: dsa: sja1105: Expose PTP timestamping ioctls to userspace")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation patch for the tc-taprio offload (and potentially
for other future offloads such as tc-mqprio).
Instead of looking directly at skb->priority during xmit, let's get the
netdev queue and the queue-to-traffic-class mapping, and put the
resulting traffic class into the dsa_8021q PCP field. The switch is
configured with a 1-to-1 PCP-to-ingress-queue-to-egress-queue mapping
(see vlan_pmap in sja1105_main.c), so the effect is that we can inject
into a front-panel's egress traffic class through VLAN tagging from
Linux, completely transparently.
Unfortunately the switch doesn't look at the VLAN PCP in the case of
management traffic to/from the CPU (link-local frames at
01-80-C2-xx-xx-xx or 01-1B-19-xx-xx-xx) so we can't alter the
transmission queue of this type of traffic on a frame-by-frame basis. It
is only selected through the "hostprio" setting which ATM is harcoded in
the driver to 7.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently handles shared block filters (for the classifier-action
qdisc) in the core due to what I believe are simply pragmatic reasons -
hiding the complexity from drivers and offerring a simple API for port
mirroring.
Extend the dsa_slave_setup_tc function by passing all other qdisc
offloads to the driver layer, where the driver may choose what it
implements and how. DSA is simply a pass-through in this case.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core, DSA taggers and DSA drivers all make use of
module_init(). Hence they get initialised at device_initcall() time.
The ordering is non-deterministic. It can be a DSA driver is bound to
a device before the needed tag driver has been initialised, resulting
in the message:
No tagger for this switch
Rather than have this be fatal, return -EPROBE_DEFER so that it is
tried again later once all the needed drivers have been loaded.
Fixes: d3b8c04988 ("dsa: Add boilerplate helper to register DSA tag driver modules")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the superfluous NET_DSA_TAG_KSZ_COMMON and just use the existing
NET_DSA_TAG_KSZ. Update the description to mention the three switch
families it supports. No functional change.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a function such as dsa_slave_create fails, currently the following
stack trace can be seen:
[ 2.038342] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.054556] sja1105 spi0.1: Reset switch and programmed static config
[ 2.063837] sja1105 spi0.1: Enabled switch tagging
[ 2.068706] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.076371] ------------[ cut here ]------------
[ 2.080973] WARNING: CPU: 1 PID: 21 at net/core/devlink.c:6184 devlink_free+0x1b4/0x1c0
[ 2.088954] Modules linked in:
[ 2.092005] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 5.3.0-rc6-01360-g41b52e38d2b6-dirty #1746
[ 2.100912] Hardware name: Freescale LS1021A
[ 2.105162] Workqueue: events deferred_probe_work_func
[ 2.110287] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 2.117992] [<c030d8cc>] (show_stack) from [<c10b08d8>] (dump_stack+0xb4/0xc8)
[ 2.125180] [<c10b08d8>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 2.132018] [<c0349d04>] (__warn) from [<c0349e34>] (warn_slowpath_null+0x40/0x48)
[ 2.139549] [<c0349e34>] (warn_slowpath_null) from [<c0f19d74>] (devlink_free+0x1b4/0x1c0)
[ 2.147772] [<c0f19d74>] (devlink_free) from [<c1064fc0>] (dsa_switch_teardown+0x60/0x6c)
[ 2.155907] [<c1064fc0>] (dsa_switch_teardown) from [<c1065950>] (dsa_register_switch+0x8e4/0xaa8)
[ 2.164821] [<c1065950>] (dsa_register_switch) from [<c0ba7fe4>] (sja1105_probe+0x21c/0x2ec)
[ 2.173216] [<c0ba7fe4>] (sja1105_probe) from [<c0b35948>] (spi_drv_probe+0x80/0xa4)
[ 2.180920] [<c0b35948>] (spi_drv_probe) from [<c0a4c1cc>] (really_probe+0x108/0x400)
[ 2.188711] [<c0a4c1cc>] (really_probe) from [<c0a4c694>] (driver_probe_device+0x78/0x1bc)
[ 2.196933] [<c0a4c694>] (driver_probe_device) from [<c0a4a3dc>] (bus_for_each_drv+0x58/0xb8)
[ 2.205414] [<c0a4a3dc>] (bus_for_each_drv) from [<c0a4c024>] (__device_attach+0xd0/0x168)
[ 2.213637] [<c0a4c024>] (__device_attach) from [<c0a4b1d0>] (bus_probe_device+0x84/0x8c)
[ 2.221772] [<c0a4b1d0>] (bus_probe_device) from [<c0a4b72c>] (deferred_probe_work_func+0x84/0xc4)
[ 2.230686] [<c0a4b72c>] (deferred_probe_work_func) from [<c03650a4>] (process_one_work+0x218/0x510)
[ 2.239772] [<c03650a4>] (process_one_work) from [<c03660d8>] (worker_thread+0x2a8/0x5c0)
[ 2.247908] [<c03660d8>] (worker_thread) from [<c036b348>] (kthread+0x148/0x150)
[ 2.255265] [<c036b348>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 2.262444] Exception stack(0xea965fb0 to 0xea965ff8)
[ 2.267466] 5fa0: 00000000 00000000 00000000 00000000
[ 2.275598] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.283729] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 2.290333] ---[ end trace ca5d506728a0581a ]---
devlink_free is complaining right here:
WARN_ON(!list_empty(&devlink->port_list));
This happens because devlink_port_unregister is no longer done right
away in dsa_port_setup when a DSA_PORT_TYPE_USER has failed.
Vivien said about this change that:
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
which is not really true. The devlink_port_unregister function _is_
being called unconditionally from within dsa_port_setup, but not for
this port that just failed, just for the previous ones which were set
up.
ports_teardown:
for (i = 0; i < port; i++)
dsa_port_teardown(&ds->ports[i]);
Initially I was tempted to fix this by extending the "for" loop to also
cover the port that failed during setup. But this could have potentially
unforeseen consequences unrelated to devlink_port or even other types of
ports than user ports, which I can't really test for. For example, if
for some reason devlink_port_register itself would fail, then
unconditionally unregistering it in dsa_port_teardown would not be a
smart idea. The list might go on.
So just make dsa_port_setup undo the setup it had done upon failure, and
let the for loop undo the work of setting up the previous ports, which
are guaranteed to be brought up to a consistent state.
Fixes: 955222ca52 ("net: dsa: use a single switch statement for port setup")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge core assumes that enabling/disabling vlan_filtering will
translate into the simple toggling of a flag for switchdev drivers.
That is clearly not the case for sja1105, which alters the VLAN table
and the pvids in order to obtain port separation in standalone mode.
There are 2 parts to the issue.
First, tag_8021q changes the pvid to a unique per-port rx_vid for frame
identification. But we need to disable tag_8021q when vlan_filtering
kicks in, and at that point, the VLAN configured as pvid will have to be
removed from the filtering table of the ports. With an invalid pvid, the
ports will drop all traffic. Since the bridge will not call any vlan
operation through switchdev after enabling vlan_filtering, we need to
ensure we're in a functional state ourselves. Hence read the pvid that
the bridge is aware of, and program that into our ports.
Secondly, tag_8021q uses the 1024-3071 range privately in
vlan_filtering=0 mode. Had the user installed one of these VLANs during
a previous vlan_filtering=1 session, then upon the next tag_8021q
cleanup for vlan_filtering to kick in again, VLANs in that range will
get deleted unconditionally, hence breaking user expectation. So when
deleting the VLANs, check if the bridge had knowledge about them, and if
it did, re-apply the settings. Wrap this logic inside a
dsa_8021q_vid_apply helper function to reduce code duplication.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After witnessing the discussion in https://lkml.org/lkml/2019/8/14/151
w.r.t. ioctl extensibility, it became clear that such an issue might
prevent that the 3 RSV bits inside the DSA 802.1Q tag might also suffer
the same fate and be useless for further extension.
So clearly specify that the reserved bits should currently be
transmitted as zero and ignored on receive. The DSA tagger already does
this (and has always did), and is the only known user so far (no
Wireshark dissection plugin, etc). So there should be no incompatibility
to speak of.
Fixes: 0471dd429c ("net: dsa: tag_8021q: Create a stable binary format")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitmap operations were introduced to simplify the switch drivers
in the future, since most of them could implement the common VLAN and
MDB operations (add, del, dump) with simple functions taking all target
ports at once, and thus limiting the number of hardware accesses.
Programming an MDB or VLAN this way in a single operation would clearly
simplify the drivers a lot but would require a new get-set interface
in DSA. The usage of such bitmap from the stack also raised concerned
in the past, leading to the dynamic allocation of a new ds->_bitmap
member in the dsa_switch structure. So let's get rid of them for now.
This commit nicely wraps the ds->ops->port_{mdb,vlan}_{prepare,add}
switch operations into new dsa_switch_{mdb,vlan}_{prepare,add}
variants not using any bitmap argument anymore.
New dsa_switch_{mdb,vlan}_match helpers have been introduced to make
clear which local port of a switch must be programmed with the target
object. While the targeted user port is an obvious candidate, the
DSA links must also be programmed, as well as the CPU port for VLANs.
While at it, also remove local variables that are only used once.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call the .port_enable and .port_disable functions for all ports,
not only the user ports, so that drivers may optimize the power
consumption of all ports after a successful setup.
Unused ports are now disabled on setup. CPU and DSA ports are now
enabled on setup and disabled on teardown. User ports were already
enabled at slave creation and disabled at slave destruction.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is currently difficult to read the different steps involved in the
setup and teardown of ports in the DSA code. Keep it simple with a
single switch statement for each port type: UNUSED, CPU, DSA, or USER.
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX timestamping is enabled and two link-local (non-meta) frames are
received in a row, this constitutes an error.
The tagger is always caching the last link-local frame, in an attempt to
merge it with the meta follow-up frame when that arrives. To recover
from the above error condition, the initial cached link-local frame is
dropped and the second frame in a row is cached (in expectance of the
second meta frame).
However, when dropping the initial link-local frame, its backing memory
was being leaked.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a meta frame is received, it is associated with the cached
sp->data->stampable_skb from the DSA tagger private structure.
Cached means its refcount is incremented with skb_get() in order for
dsa_switch_rcv() to not free it when the tagger .rcv returns NULL.
The mistake is that skb_unref() is not the correct function to use. It
will correctly decrement the refcount (which will go back to zero) but
the skb memory will not be freed. That is the job of kfree_skb(), which
also calls skb_unref().
But it turns out that freeing the cached stampable_skb is in fact not
necessary. It is still a perfectly valid skb, and now it is even
annotated with the partial RX timestamp. So remove the skb_copy()
altogether and simply pass the stampable_skb with a refcount of 1
(incremented by us, decremented by dsa_switch_rcv) up the stack.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the CPU port registers dump into the master interface registers
dump through ethtool, by nesting the ethtool_drvinfo and ethtool_regs
structures of the CPU port into the dump.
drvinfo->regdump_len will contain the full data length, while regs->len
will contain only the master interface registers dump length.
This allows for example to dump the CPU port registers on a ZII Dev
C board like this:
# ethtool -d eth1
0x004: 0x00000000
0x008: 0x0a8000aa
0x010: 0x01000000
0x014: 0x00000000
0x024: 0xf0000102
0x040: 0x6d82c800
0x044: 0x00000020
0x064: 0x40000000
0x084: RCR (Receive Control Register) 0x47c00104
MAX_FL (Maximum frame length) 1984
FCE (Flow control enable) 0
BC_REJ (Broadcast frame reject) 0
PROM (Promiscuous mode) 0
DRT (Disable receive on transmit) 0
LOOP (Internal loopback) 0
0x0c4: TCR (Transmit Control Register) 0x00000004
RFC_PAUSE (Receive frame control pause) 0
TFC_PAUSE (Transmit frame control pause) 0
FDEN (Full duplex enable) 1
HBC (Heartbeat control) 0
GTS (Graceful transmit stop) 0
0x0e4: 0x76735d6d
0x0e8: 0x7e9e8808
0x0ec: 0x00010000
.
.
.
88E6352 Switch Port Registers
------------------------------
00: Port Status 0x4d04
Pause Enabled 0
My Pause 1
802.3 PHY Detected 0
Link Status Up
Duplex Full
Speed 100 or 200 Mbps
EEE Enabled 0
Transmitter Paused 0
Flow Control 0
Config Mode 0x4
01: Physical Control 0x003d
RGMII Receive Timing Control Default
RGMII Transmit Timing Control Default
200 BASE Mode 100
Flow Control's Forced value 0
Force Flow Control 0
Link's Forced value Up
Force Link 1
Duplex's Forced value Full
Force Duplex 1
Force Speed 100 or 200 Mbps
.
.
.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kconfig option is unused, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DSA tag code for Microchip KSZ8795 switch. The switch is simpler
and the tag is only 1 byte, instead of 2 as is the case with KSZ9477.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.
This patch restores the block sharing feature.
Fixes: da3eeb904f ("net: flow_offload: add list handling functions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this type definition and adapt users.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.
Fixes: d63db30c85 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function sk_buff()
in the error handling case.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the flooding of
unknown multicast traffic on the CPU ports, depending on the value
of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute.
The current behavior is kept unchanged but a user can now prevent
the CPU conduit to be flooded with a lot of unregistered traffic that
the network stack needs to filter in software with e.g.:
echo 0 > /sys/class/net/br0/multicast_router
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the dsa_slave_switchdev_port_{attr_set,obj}_event functions
in favor of the switchdev_handle_port_{attr_set,obj_add,obj_del}
helpers which recurse into the lower devices of the target interface.
This has the benefit of being aware of the operations made on the
bridge device itself, where orig_dev is the bridge, and dev is the
slave. This can be used later to configure the hardware switches.
Only VLAN and (port) MDB objects not directly targeting the slave
device are unsupported at the moment, so skip this case in their
respective case statements.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev handle helpers make use of a device checking helper
requiring a const net_device. Make dsa_slave_dev_check compliant
to this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current DSA code handling switchdev objects does not recurse into
the lower devices thus is never called with an orig_dev member being
a bridge device, hence remove this useless check.
At the same time, remove the comments about the callers, which is
unlikely to be updated if the code changes and thus will be confusing.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packing facility is needed to decode Ethernet meta frames containing
source port and RX timestamping information.
The DSA driver selects CONFIG_PACKING, but the tagger did not, and since
taggers can be now compiled as modules independently from the drivers
themselves, this is an issue now, as CONFIG_PACKING is disabled by
default on all architectures.
Fixes: e53e18a6fe ("net: dsa: sja1105: Receive and decode meta frames")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to specifically deal with phylink_of_phy_connect() returning
-ENODEV, because this can happen when a CPU/DSA port does connect
neither to a PHY, nor has a fixed-link property. This is a valid use
case that is permitted by the binding and indicates to the switch:
auto-configure port with maximum capabilities.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn