It is a copy/paste of patch provided by Sujith for ath9k.
"Even though we make sure PowerSave is not enabled by default
by disabling the flag, WIPHY_FLAG_PS_ON_BY_DEFAULT on init,
PS could be enabled by userspace based on various factors
like battery usage etc. Since PS in ath9k is just broken
and has been untested for years, remove support for it, but
allow a user to explicitly enable it using a module parameter."
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On suspend/resume, firmware will restart and gpios
configuration will be reseted. Restore this
configureation at least for LEDs
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.
This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.
Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1
Tested-by: Bo Shi <cnshibo@gmail.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed so the interface combination can still be
validated when CONFIG_MAC80211_MESH is not enabled.
Otherwise wiphy registration fails.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All known ar7010+ar* device and current FW support STBC TX. This patch
make use of it and suggest to send STBC if peer support it.
I use wort "suggest" since currenly we have separate rate controller
in FW which will make decision based on rate and hardware.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Advertise support for management frame protection in hardware.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
More specifically, enable AP-style beaconing on mesh
ifaces and change the hw capabilities to reflect mesh
support.
Coexistence with a virtual STA interface was tested as
working fine.
Signed-off-by: Javier Cardona <javier@cozybit.com>
[rebase, add iface combinations]
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the firmware has been open sourced, the minor version has been
bumped to 1.4 and the API/ABI will stay compatible across further 1.x
releases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the macros provided by mac80211 and remove redundant
declarations inside the drivers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to create virtual interface the driver supports.
Also this ensures multivif support and limitation advertised
by the driver is taken care in cfg80211 itself.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable BTCOEX for WB193(which seems to be the only supported
ath9k_htc BTCOEX chipset)only when it is enabled via modparam,
rather than enabling it by default.
Cc: Vivek Natarajan <nataraja@qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.
Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.
Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip group keys configuration in hardware in order to make IBSS RSN work.
Keys will be managed using software.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.
This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.
On MIPS this reduces the total size for the modules by about 20k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.
Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we already have ah->{rx,tx}chainmask for the same purpose
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce the credit size for UB94/95 to fix target hangs.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_htc: Fix AMPDU subframe handling" registered the maximum
subframe limit of the driver with mac80211, which was used in ADDBA
negotiation. While technically correct, this causes inter-operability issues
with a few APs. Revert to the older behavior to fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the convoluted hacks in the driver and simplify things
by making use of mac80211's LED triggers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump the firmware version to 1.2
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Register the driver's maximum ampdu subframe limit to mac80211.
* Cleanup the target capabilities structure and fix an endian issue.
* Fix BTCOEX by sending a command to the target when the BT priority
changes.
* Bump the required firmware version to 1.1
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the ath9k_htc debugfs under ieee80211 to be inline
with ath9k driver and it also helps to simplify debug code.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally, a WMI event would arrive ahead of the TX
URB completion handler. Discarding these events would exhaust
the available TX slots, so handle them by running a timer
cleaning up such events. Also, timeout packets for which TX
completion events have not arrived.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the infrastructure is in place, process WMI
TX status events and complete packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a queue to handle WMI events and schedule a tasklet
to process the events. This fixes the race between the
WMI event ISR and the SWBA tasklet when the arrival of
WMI events in quick succession could overwrite the SWBA
data before the tasklet from a previous iteration could
have been scheduled. Also, drain the WMI queue properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the CAB endpoint to send buffered multicast or
broadcast frames after each SWBA event.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oleksij Rempel