According to Rev.0.51 datasheet 004_R-CarV4H_pin_function.xlsx,
GP1_23 - GP1_28 are 1.8/3.3V. But they are not on Table 7.28.
According to the HW team, there are no bits assigned.
This patch follows HW team's comment.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8735fltxwg.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Current R-Car V4H PFC code has many MOD_SELx definitions with all 0.
But these have no meaning. This patch removes them.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875ykhtxym.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Current R-Car V4H PFC code has many IPxSRx definitions with all 0.
But these have no meaning. This patch removes them.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877d4xtxyv.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Current R-Car V4H PFC code has many NOGP definitions. But these are not
used, and they are different from original usage. This patch removes
them.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878rpdtxz8.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
MODSEL8 controls I2C vs. GPIO modes, and the Datasheet (Rev.0.51) is
indicating that I2C needs 1. But we should use 0 for all cases in
reality. New Datasheet should be updated.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87a69ttxzg.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds initial pinctrl support for the R-Car V4H (R8A779G0)
SoC, including bias, drive strength and voltage control.
This patch was created based on the Rev.0.51 datasheet.
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Morimoto: merge Kihara-san's MODSEL8 fixup patch, cleanup white space, care about reserved bits on each configs, fixup comments, etc.]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87czepty0j.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add PORT_GP_CFG_13() and PORT_GP_13() helper macros, to be used by the
r8a779g0 subdriver.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87edz5ty0r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for pin and gpio controller driver for RZ/V2M SoC.
Based on the RZ/G2L driver.
Note that the DETDO and DETMS dedicated pins are currently not
documented in the HW manual as to which pin group they are in.
HW team has since said that the output level of 1.8V I/O group 4
(for MD0-7, and debugger) is the same as the 1.8V I/O group 3.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220624084833.22605-3-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pin status reported by pinconf-pins file always reported pin status as
"input enabled" even for pins which had input disabled. Fix this by
returning -EINVAL for the pins which have input disabled.
Fixes: c4c4637eb5 ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220511094057.3151-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The PULMD bits and the SEC bit in the PORTCR register descriptions on
SH/R-Mobile SoCs are either unused or unsupported. Describe them as
reserved bits using a negative field width value, and drop the
corresponding dummy enum IDs.
This reduces kernel size by 2832 (R-Mobile APE6), 2544 (R-Mobile A1),
and/or 3228 (SH-Mobile AG5) bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1b123d8f04c2314d5a7a87004971868ba2176499.1649865241.git.geert+renesas@glider.be
Currently, reserved register fields must be fully described using dummy
enum IDs (zeroes), one for each possible state (2^bits states).
Add support for describing reserved fields using negative field width
values as shorthands, thus removing the need for dummy values. Apart
from the obvious size reduction due to the removal of the dummy values,
this will also enable merging adjacent reserved fields into a single
field, reducing the number of fields to describe, and thus kernel size.
Update the checker accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cad7c92ef039d9a4d039807efc15886a7aa862be.1649865241.git.geert+renesas@glider.be
All fields in the IPSR registers on RZ/G1C have the same width, but the
driver describes them using the PINMUX_CFG_REG_VAR() macro, which
is intended for fields with different widths. Convert the description
to use the PINMUX_CFG_REG() macro for fixed-width fields instead.
This reduces kernel size by 162 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f6f26a0dfd16050ead83daf2b9fabeb8b26821a6.1649865241.git.geert+renesas@glider.be
* Introduce helpers to iterate over GPIO chip nodes and covert some drivers
The following is an automated git shortlog grouped by driver:
gpiolib:
- Introduce a helper to get first GPIO controller node
- Introduce gpiochip_node_count() helper
- Introduce for_each_gpiochip_node() loop helper
pinctrl:
- meson: Replace custom code by gpiochip_node_count() call
- meson: Enable COMPILE_TEST
- meson: Rename REG_* to MESON_REG_*
- armada-37xx: Reuse GPIO fwnode in armada_37xx_irqchip_register()
- armada-37xx: Switch to use fwnode instead of of_node
- samsung: Switch to use for_each_gpiochip_node() helper
- samsung: Drop redundant node parameter in samsung_banks_of_node_get()
- npcm7xx: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Replace custom code by gpiochip_node_count() call
- stm32: Switch to use for_each_gpiochip_node() helper
- stm32: Replace custom code by gpiochip_node_count() call
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSu93Raj3rZDNXzGZv7cr9lmVa5zAUCYmwsmgAKCRD7cr9lmVa5
zEYPAP4q31AbTJHk6Fs1A79esVSo+DZSkZSzbk/n8Vr3oYG56gD/dVu5EmLNKPHU
6o5+BvdXqjHrymihHasdyD9YqI30zwM=
=MIEU
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.19-1
* Introduce helpers to iterate over GPIO chip nodes and covert some drivers
The following is an automated git shortlog grouped by driver:
gpiolib:
- Introduce a helper to get first GPIO controller node
- Introduce gpiochip_node_count() helper
- Introduce for_each_gpiochip_node() loop helper
pinctrl:
- meson: Replace custom code by gpiochip_node_count() call
- meson: Enable COMPILE_TEST
- meson: Rename REG_* to MESON_REG_*
- armada-37xx: Reuse GPIO fwnode in armada_37xx_irqchip_register()
- armada-37xx: Switch to use fwnode instead of of_node
- samsung: Switch to use for_each_gpiochip_node() helper
- samsung: Drop redundant node parameter in samsung_banks_of_node_get()
- npcm7xx: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Switch to use for_each_gpiochip_node() helper
- renesas: rza1: Replace custom code by gpiochip_node_count() call
- stm32: Switch to use for_each_gpiochip_node() helper
- stm32: Replace custom code by gpiochip_node_count() call
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220429082637.1308182-2-yangyingliang@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: c7977ec4a3 ("pinctrl: sh-pfc: Convert to platform_get_*()")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220429082637.1308182-1-yangyingliang@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Unlike on R-Car Gen3 SoCs, setting a bit to zero in a GPIO / Peripheral
Function Select Register (GPSRn) on R-Car S4-8 is not always sufficient
to configure a pin for GPIO. For I2C-capable pins, the I2C function
must also be explicitly disabled in the corresponding Module Select
Register (MODSELn).
Add the missing FN_SEL_I2Ci_0 function enums to the pinmux_data[] array
by temporarily overriding the GP_1_j_FN function enum to expand to two
enums: the original GP_1_j_FN enum to configure the GPSR register bits,
and the missing FN_SEL_I2Ci_0 enum to configure the MODSEL register
bits.
Fixes: 030ac6d7ee ("pinctrl: renesas: Initial R8A779F0 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c12c60ec1058140a37f03650043ab73f730f104f.1650610471.git.geert+renesas@glider.be
Unlike on R-Car Gen3 SoCs, setting a bit to zero in a GPIO / Peripheral
Function Select Register (GPSRn) on R-Car V3U is not always sufficient
to configure a pin for GPIO. For I2C-capable pins, the I2C function
must also be explicitly disabled in the corresponding Module Select
Register (MODSELn).
Add the missing FN_SEL_I2Ci_0 function enums to the pinmux_data[] array
by temporarily overriding the GP_2_j_FN function enum to expand to two
enums: the original GP_2_j_FN enum to configure the GSPR register bits,
and the missing FN_SEL_I2Ci_0 enum to configure the MODSEL register
bits.
Fixes: 741a7370fc ("pinctrl: renesas: Initial R8A779A0 (V3U) PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/4611e29e7b105513883084c1d6dc39c3ac8b525c.1650610471.git.geert+renesas@glider.be
GPIO (PINCTRL) block is identical on Renesas RZ/G2L, RZ/G2UL and RZ/V2L
SoC's, so instead of selecting PINCTRL_RZG2L config for each SoC select
PINCTRL_RZG2L config option if ARCH_RZG2L is enabled. The ARCH_RZG2L
config option is already selected by ARCH_R9A07G043, ARCH_R9A07G044 and
ARCH_R9A07G054.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220406075318.14385-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/G2UL SoC has fewer pins compared to RZ/G2L and the port pin
definitions are different compared to RZ/G2L.
This patch adds a new compatible to take care of these differences by
adding r9a07g043_data with r9a07g043_gpio_configs and
rzg2l_dedicated_pins.common.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220401180230.19950-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and functions for the SPI Multi I/O Bus Controller
(RPC-IF) to the R8A77990 PFC driver. They are to be used when an
Octal-SPI Flash or HyperFlash is connected.
Redefine the QSPI[01] pin groups using the RPC DQ[0:7] pin data, to save
memory.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/ec9735bb3468225e04ac6cb95e11a0e237b2b9ed.1648547080.git.geert+renesas@glider.be
According to R-Car Gen3 HW documentation 2.20 onwards, drive-strength is
introduced to r8a77990. It is also documented for r8a774c0. Add it to
the pinctrl driver.
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220320092542.2308-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The checker code to iterate over all drive strength and bias register
description items is cumbersome, due to the repeated calculation of
indices, and the use of hardcoded array sizes. The latter was done
under the assumption they would never need to be changed, which turned
out to be false.
Increase readability by introducing helper macros to access drive
strength and bias register description items.
Increase maintainability by replacing hardcoded numbers by array sizes
calculated at compile-time.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/5051ae56a1388ccf2d283dfc9624de2991cce914.1650355619.git.geert+renesas@glider.be
Switch the code to use for_each_gpiochip_node() helper.
While at it, in order to avoid additional churn in the future,
switch to fwnode APIs where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since we have generic function to count GPIO controller nodes
under a given device, there is no need to open code it. Replace
custom code by gpiochip_node_count() call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Clock-Synchronized Serial
Interfaces with FIFO (MSIOF) on the Renesas R-Car S4-8 (R8A779F0) SoC.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/c625769714b1027a756dd2ed4a017eb24708a041.1645457792.git.geert+renesas@glider.be
Add pins, groups, and functions for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) on the Renesas R-Car S4-8 (R8A779F0) SoC.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/2b85b8857c1189fa6ee33e2f57fe746d740481d1.1645457792.git.geert+renesas@glider.be
Add pins, groups, and functions for the Serial Communication Interfaces
with FIFO (SCIF) on the Renesas R-Car S4-8 (R8A779F0) SoC.
Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/6369359a53483291ee536787c8a232462ff1b3a9.1645457792.git.geert+renesas@glider.be
Add initial Pin Function Controller (PFC) support for the Renesas R-Car
S4-8 (R8A779F0) SoC, including bias, drive strength and voltage control.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/fd8201da404b7b0897130b254380ffc97f437266.1645457792.git.geert+renesas@glider.be
Linus reports that some Renesas pin control sub-drivers are still
including <linux/gpio.h> instead of <linux/gpio/driver.h>. As these
sub-drivers don't need either, the includes can just be removed.
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/578825d779b45af745cc7623c7f69d2ddeadac4b.1645605227.git.geert+renesas@glider.be
The checker failed to validate all enum IDs in the description of a
register with fixed-width register fields, due to a miscalculation of
the number of described states: each register field of n bits can have
"1 << n" possible states, not "1".
Increase SH_PFC_MAX_ENUMS accordingly, now more enum IDs are checked
(SH-Mobile AG5 has more than 4000 enum IDs defined).
Fixes: 12d057bad6 ("pinctrl: sh-pfc: checker: Add check for enum ID conflicts")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6d8a6a05564f38f9d20464c1c17f96e52740cf6a.1645460429.git.geert+renesas@glider.be
Validate consistency of the pin control tables for pins with I/O voltage
capabilities. If a pin has I/O voltage register bits declarations
through .pin_to_pocctrl(), the SH_PFC_PIN_CFG_IO_VOLTAGE flag should be
set in the pin's configs, and vice versa.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/de81cced01ae3f26d341177d66d4b8e918fbfb76.1640270559.git.geert+renesas@glider.be
Validate consistency of the pin control tables for pins with drive
strength capabilities. If a pin has drive strength register bits
declarations in drive_regs[], the SH_PFC_PIN_CFG_DRIVE_STRENGTH flag
should be set in the pin's configs, and vice versa.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0d5de01b5fe2c5fd23c3bea41077dc57ad105b9e.1640270559.git.geert+renesas@glider.be
Validate consistency of the pin control tables for pins with pull-up
and/or pull-down capabilities. If a pin has bias register bits
declarations in bias_regs[] or through .pin_to_portcr(), the
corresponding SH_PFC_PIN_CFG_PULL* flags should be set in the pin's
configs, and vice versa, and the .get_bias() and .set_bias() callbacks
should be implemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/19b3e0773fbb36c015a43db683f79e75b0fec3ee.1640270559.git.geert+renesas@glider.be
Kuninori Morimoto