After the good discussion with Florian from here:
https://lore.kernel.org/netdev/20200911000337.htwr366ng3nc3a7d@skbuf/
I realized that the VLAN settings on the NPI port (the hardware "CPU port",
in DSA parlance) don't actually make any difference, because that port
is hardcoded in hardware to use what mv88e6xxx would call "unmodified"
egress policy for VLANs.
So earlier patch 183be6f967 ("net: dsa: felix: send VLANs on CPU port
as egress-tagged") was incorrect in the sense that it didn't actually
make the VLANs be sent on the NPI port as egress-tagged. It only made
ocelot_port_set_native_vlan shut up.
Now that we have moved the check from ocelot_port_set_native_vlan to
ocelot_vlan_prepare, we can simply shunt ocelot_vlan_prepare from DSA,
and avoid calling it. This is the correct way to deal with things,
because the NPI port configuration is DSA-specific, so the ocelot switch
library should not have the check for multiple native VLANs refined in
any way, it is correct the way it is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Put the preparation phase of switchdev VLAN objects to some good use,
and move the check we already had, for preventing the existence of more
than one egress-untagged VLAN per port, to the preparation phase of the
addition.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qca8k only supports a switch-wide MTU setting, and the code to take
the max of all ports was only looking at the port currently being set.
Fix to examine all ports.
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: f58d2598cf ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201030183315.GA6736@earth.li
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA assumes that a bridge which has vlan filtering disabled is not
vlan aware, and ignores all vlan configuration. However, the kernel
software bridge code allows configuration in this state.
This causes the kernel's idea of the bridge vlan state and the
hardware state to disagree, so "bridge vlan show" indicates a correct
configuration but the hardware lacks all configuration. Even worse,
enabling vlan filtering on a DSA bridge immediately blocks all traffic
which, given the output of "bridge vlan show", is very confusing.
Allow the VLAN configuration to be updated on Marvell DSA bridges,
otherwise we end up cutting all traffic when enabling vlan filtering.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1kYAU3-00071C-1G@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate the const array rate_table on the stack but instead it
static. Makes the object code smaller by 46 bytes.
Before:
text data bss dec hex filename
29812 3824 192 33828 8424 drivers/net/dsa/bcm_sf2.o
After:
text data bss dec hex filename
29670 3920 192 33782 83f6 drivers/net/dsa/bcm_sf2.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201020165029.56383-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC9953 Seville switch has 2 megabits of buffer split into 4360
words of 60 bytes each. 2048 * 1024 is 2 megabytes instead of 2 megabits.
2 megabits is (2048 / 8) * 1024 = 256 * 1024.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: a63ed92d21 ("net: dsa: seville: fix buffer size of the queue system")
Link: https://lore.kernel.org/r/20201019050625.21533-1-fido_max@inbox.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).
Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().
Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
\--ksz_switch_register()
+--dsa_register_switch()
| \--dsa_switch_probe()
| \--dsa_tree_setup()
| \--dsa_tree_setup_switches()
| +--dsa_switch_setup()
| | +--ksz9477_setup()
| | | \--ksz_init_mib_timer()
| | | |--/* Start the timer 2 seconds later. */
| | | \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
| | \--__mdiobus_register()
| | \--mdiobus_scan()
| | \--get_phy_device()
| | +--get_phy_id()
| | \--phy_device_create()
| | |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
| | \--request_module()
| |
| \--dsa_port_setup()
| +--/* Called for non-CPU ports */
| +--dsa_slave_create()
| | +--/* Too late, ksz_mib_read_work() may be called beforehand */
| | \--port->slave = ...
| ...
| +--Called for CPU port */
| \--dsa_port_link_register_of()
| \--ksz_mac_link_down()
| +--/* mib_read must be initialized here */
| +--/* work is already scheduled, so it will be executed after 2000 ms */
| \--schedule_delayed_work(&dev->mib_read, 0);
\-- /* here port->slave is setup properly, scheduling the delayed work should be safe */
Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.
Fixes: 7c6ff470aa ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MTU setting for this DSA switch is global so we need
to keep track of the MTU set for each port, then as soon
as any MTU changes, roof the MTU to the biggest common
denominator and poke that into the switch MTU setting.
To achieve this we need a per-chip-variant state container
for the RTL8366RB to use for the RTL8366RB-specific
stuff. Other SMI switches does seem to have per-port
MTU setting capabilities.
Fixes: 5f4a8ef384 ("net: dsa: rtl8366rb: Support setting MTU")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a devlink region to return the per port registers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a strictly cosmetic change that renames some macros in
sja1105_dynamic_config.c. They were copy-pasted in haste and this has
resulted in them having the driver prefix twice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VCAP IS1 is a VCAP module which can filter on the most common L2/L3/L4
Ethernet keys, and modify the results of the basic QoS classification
and VLAN classification based on those flow keys.
There are 3 VCAP IS1 lookups, mapped over chains 10000, 11000 and 12000.
Currently the driver is hardcoded to use IS1_ACTION_TYPE_NORMAL half
keys.
Note that the VLAN_MANGLE has been omitted for now. In hardware, the
VCAP_IS1_ACT_VID_REPLACE_ENA field replaces the classified VLAN
(metadata associated with the frame) and not the VLAN from the header
itself. There are currently some issues which need to be addressed when
operating in standalone, or in bridge with vlan_filtering=0 modes,
because in those cases the switch ports have VLAN awareness disabled,
and changing the classified VLAN to anything other than the pvid causes
the packets to be dropped. Another issue is that on egress, we expect
port tagging to push the classified VLAN, but port tagging is disabled
in the modes mentioned above, so although the classified VLAN is
replaced, it is not visible in the packet transmitted by the switch.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.
Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to the DSA receive path that we need to untage the bridge PVID,
this allows us to remove the dsa_untag_bridge_pvid() calls from
net/dsa/tag_brcm.c.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are deriving these from the constants exposed by the
hardware, we can delete the static info we're keeping in the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the actions are packed together in the action RAM, an incorrect
action width means that no action except the first one would behave
correctly.
The tc-flower offload has probably not been tested on this hardware
since its introduction.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port mask width was larger than the actual number of ports, and
therefore, all fields following this one were also shifted by the number
of excess bits. But the driver doesn't use the REW_OP, SMAC_REPLACE_ENA
or ACL_ID bits from the action vector, so the bug was inconsequential.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ocelot_configure_cpu() function, which was in fact bringing
up 2 ports: the CPU port module, which both switchdev and DSA have, and
the NPI port, which only DSA has.
The (non-Ethernet) CPU port module is at a fixed index in the analyzer,
whereas the NPI port is selected through the "ethernet" property in the
device tree.
Therefore, the function to set up an NPI port is DSA-specific, so we
move it there, simplifying the ocelot switch library a little bit.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the driver name and ASIC ID so that generic user space
application are able to know they're looking at sja1105 devlink regions
when pretty-printing them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in Documentation/networking/dsa/sja1105.rst, this switch
has a static config held in the driver's memory and re-uploaded from
time to time into the device (after any major change).
The format of this static config is in fact described in UM10944.pdf and
it contains all the switch's settings (it also contains device ID, table
CRCs, etc, just like in the manual). So it is a useful and universal
devlink region to expose to user space, for debugging purposes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll have more devlink code soon. Group it together in a separate
translation object.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous implementation failed to account for the "ports" node. The
actual port nodes are not child nodes of the switch node, but a "ports"
node sits in between.
Fixes: edecfa98f6 ("net: dsa: microchip: look for phy-mode in port nodes")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->speed holds a value of 10, 100, 1000 or 2500, but
QSYS_TAG_CONFIG_LINK_SPEED expects a value of 0, 1, 2, 3. So convert the
speed to a proper value.
Fixes: de143c0e27 ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload")
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.
This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the B53 driver to support VLANs while not filtering. This
requires us to enable VLAN globally within the switch upon driver
initial configuration (dev->vlan_enabled).
We also need to remove the code that dealt with PVID re-configuration in
b53_vlan_filtering() since that function worked under the assumption
that it would only be called to make a bridge VLAN filtering, or not
filtering, and we would attempt to move the port's PVID accordingly.
Now that VLANs are programmed all the time, even in the case of a
non-VLAN filtering bridge, we would be programming a default_pvid for
the bridged switch ports.
We need the DSA receive path to pop the VLAN tag if it is the bridge's
default_pvid because the CPU port is always programmed tagged in the
programmed VLANs. In order to do so we utilize the
dsa_untag_bridge_pvid() helper introduced in the commit before within
net/dsa/tag_brcm.c.
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to include MDIO address 0, which is how our Device Tree blobs
indicate where to find the external BCM53125 switches.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the switch driver is written such that port 5 or 8 could be CPU
ports, the use case on Broadcom STB chips is to use port 8 exclusively.
The platform firmware does make port 5 comply to a proper DSA CPU port
binding by specifiying an "ethernet" phandle. This is undesirable for
now until we have an user-space configuration mechanism (such as
devlink) which could support dynamically changing the port flavor at
run time.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an off-by-one error in rtl8366rb_is_vlan_valid()
making VLANs 0..4094 valid while it should be 1..4095.
Fix it.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mt7531_cpu_port_config(), if the variable port is neither 5 nor 6,
then variable interface will be used uninitialised. Change the function
to return -EINVAL in this case.
As the return value of mt7531_cpu_port_config() is never checked
(even though it returns an int) add a check in the correct place so that
the error can be passed up the call stack. Now that we correctly handle
errors thrown in this function, also check the return value of
mt7531_mac_config() in case an error occurs here. Also add misisng
checks to mt7530_setup() and mt7531_setup(), which are another level
further up the call stack.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Addresses-Coverity: 1496993 ("Uninitialized variables")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole purpose of tag_8021q is to send VLAN-tagged traffic to the
CPU, from which the driver can decode the source port and switch id.
Currently this only works if the VLAN filtering on the master is
disabled. Change that by explicitly adding code to tag_8021q.c to add
the VLANs corresponding to the tags to the filter of the master
interface.
Because we now need to call vlan_vid_add, then we also need to hold the
RTNL mutex. Propagate that requirement to the callers of dsa_8021q_setup
and modify the existing call sites as appropriate. Note that one call
path, sja1105_best_effort_vlan_filtering_set -> sja1105_vlan_filtering
-> sja1105_setup_8021q_tagging, was already holding this lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We go to lengths to determine whether the PVID should be set
for this port or not, and then fail to take it into account.
Fix this oversight.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the driver name and the asic.id with the switch name.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the global registers, and the ATU to be snapshot via devlink
regions. It is later planned to add support for the port registers.
v2:
Remove left over debug prints
Comment ATU format is generic for mv88e6xxx, not wider
v3:
Make use of ops structure passed to snapshot function
Remove port regions
v4:
Make use of enum mv88e6xxx_region_id
Fix global2/global1 read typ0
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code in mv88e6xxx_atu_new() which builds a bitmaps of
FIDs in use into a helper function. This will be reused by the devlink
code when dumping the ATU.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will soon be more devlink code. Move the existing code into a
file of its own, before we start adding this new code.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seville does not need to depend on PCI or on the ENETC MDIO controller.
There will also be other compile-time differences in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only does Sevile not have a PTP clock, but with separate modules,
this structure cannot even live in felix.c, due to the .owner =
THIS_MODULE assignment causing this link time error:
drivers/net/dsa/ocelot/felix.o:(.data+0x0): undefined reference to `__this_module'
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we don't plan on making any changes to this function, currently
this is the only remaining dependency between felix and seville, after
the PCS has been refactored out into pcs-lynx.c.
Duplicate this function in seville to break the dependency completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the time, some patches have introduced structures aligned with
spaces, near structures aligned with tabs. Fix the inconsistencies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reindent these definitions to be in line with the rest of the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some definitions were likely copied from
drivers/net/mdio/mdio-mscc-miim.c.
They are not necessary, remove them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overall idea (issue soft reset, enable memories, initialize
memories, enable core) is the same, so it would make sense that an
attempt is made to unify the procedures.
It is not immediately obvious that the fields are not part of the same
register targets, though. So add a comment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per documentation, proper startup sequence is:
* Enable memories
* Initialize memories
* Enable core
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is another one of these right above the readx_poll_status.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these helpers for regmap fields are available, use them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mscc_ocelot_init_ports() will skip initializing a port when it
doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
NULL. Take this into consideration when tearing down the driver, and add
a new function ocelot_deinit_port() to the switch library, mirror of
ocelot_init_port(), which needs to be called by the driver for all ports
it has initialized.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_init() allocates memory, resets the switch and polls for a status
register, things which can fail. Stop probing the driver in that case,
and propagate the error result.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC9953 Seville switch has 2 megabits of buffer split into 4360
words of 60 bytes each.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 and KSZ8795 use the port_cnt field differently: For the
KSZ9477, it includes the CPU port(s), while for the KSZ8795, it doesn't.
It would be a good cleanup to make the handling of both drivers match,
but as a first step, fix the recently broken assignment of num_ports in
the KSZ8795 driver (which completely broke probing, as the CPU port
index was always failing the num_ports check).
Fixes: af199a1a9c ("net: dsa: microchip: set the correct number of ports")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new support for MT7531:
MT7531 is the next generation of MT7530. It is also a 7-ports switch with
5 giga embedded phys, 2 cpu ports, and the same MAC logic of MT7530. Cpu
port 6 only supports SGMII interface. Cpu port 5 supports either RGMII
or SGMII in different HW sku, but cannot be muxed to PHY of port 0/4 like
mt7530. Due to SGMII interface support, pll, and pad setting are different
from MT7530. This patch adds different initial setting, and SGMII phylink
handlers of MT7531.
MT7531 SGMII interface can be configured in following mode:
- 'SGMII AN mode' with in-band negotiation capability
which is compatible with PHY_INTERFACE_MODE_SGMII.
- 'SGMII force mode' without in-band negotiation
which is compatible with 10B/8B encoding of
PHY_INTERFACE_MODE_1000BASEX with fixed full-duplex and fixed pause.
- 2.5 times faster clocked 'SGMII force mode' without in-band negotiation
which is compatible with 10B/8B encoding of
PHY_INTERFACE_MODE_2500BASEX with fixed full-duplex and fixed pause.
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a structure holding required operations for each device such as device
initialization, PHY port read or write, a checker whether PHY interface is
supported on a certain port, MAC port setup for either bus pad or a
specific PHY interface.
The patch is done for ready adding a new hardware MT7531, and keep the
same setup logic of existing hardware.
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refine message in Kconfig with fixing typo and an explicit MT7621 support.
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on another tag_8021q driver implementation, some things
became apparent:
- It is not mandatory for a DSA driver to offload the tag_8021q VLANs by
using the VLAN table per se. For example, it can add custom TCAM rules
that simply encapsulate RX traffic, and redirect & decapsulate rules
for TX traffic. For such a driver, it makes no sense to receive the
tag_8021q configuration through the same callback as it receives the
VLAN configuration from the bridge and the 8021q modules.
- Currently, sja1105 (the only tag_8021q user) sets a
priv->expect_dsa_8021q variable to distinguish between the bridge
calling, and tag_8021q calling. That can be improved, to say the
least.
- The crosschip bridging operations are, in fact, stateful already. The
list of crosschip_links must be kept by the caller and passed to the
relevant tag_8021q functions.
So it would be nice if the tag_8021q configuration was more
self-contained. This patch attempts to do that.
Create a struct dsa_8021q_context which encapsulates a struct
dsa_switch, and has 2 function pointers for adding and deleting a VLAN.
These will replace the previous channel to the driver, which was through
the .port_vlan_add and .port_vlan_del callbacks of dsa_switch_ops.
Also put the list of crosschip_links into this dsa_8021q_context.
Drivers that don't support cross-chip bridging can simply omit to
initialize this list, as long as they dont call any cross-chip function.
The sja1105_vlan_add and sja1105_vlan_del functions are refactored into
a smaller sja1105_vlan_add_one, which now has 2 entry points:
- sja1105_vlan_add, from struct dsa_switch_ops
- sja1105_dsa_8021q_vlan_add, from the tag_8021q ops
But even this change is fairly trivial. It just reflects the fact that
for sja1105, the VLANs from these 2 channels end up in the same hardware
table. However that is not necessarily true in the general sense (and
that's the reason for making this change).
The rest of the patch is mostly plain refactoring of "ds" -> "ctx". The
dsa_8021q_context structure needs to be propagated because adding a VLAN
is now done through the ops function pointers inside of it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in calling dsa_port_setup_8021q_tagging for each
individual port. Additionally, it will become more difficult to do that
when we'll have a context structure to tag_8021q (next patch). So
refactor this now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/devicetree/bindings/net/dsa/dsa.txt says that the phy-mode
property should be specified on port nodes. However, the microchip
drivers read it from the switch node.
Let the driver use the per-port property and fall back to the old
location with a warning.
Fix in-tree users.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Link: https://lore.kernel.org/netdev/20200617082235.GA1523@laureti-dev/
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already maintain an array of VLANs used by the switch so we can
simply iterate over it to report the occupancy via devlink.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheet for the ksz9893 and ksz9477 switches recommend waiting at
least 100us after the de-assertion of reset before trying to program the
device through any interface.
Also switch the existing msleep() call to usleep_range() as recommended
in Documentation/timers/timers-howto.rst. The 2ms range used here is
somewhat arbitrary, as long as the reset is asserted for at least 10ms
we should be ok.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't assume that the link partner supports the in-band status
reporting which is enabled by default on the KSZ9893 when using RGMII
for the upstream port.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always print the selected phy mode for the CPU port when using the
ksz9477 driver. If the phy mode was changed, also print the previous
mode to aid in debugging.
To make the message more clear, prefix it with the port number which it
applies to and improve the language a little.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make switch detection more informative print the result of the
ksz9477/ksz9893 compatibility check. With debug output enabled also
print the contents of the Chip ID registers as a 40-bit hex string.
As this detection is the first communication with the switch performed
by the driver, making it easy to see any errors here will help identify
issues with SPI data corruption or reset sequencing.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switches the RTL8366RB over to using phylink callbacks
instead of .adjust_link(). This is a pretty template
switchover. All we adjust is the CPU port so that is why
the code only inspects this port.
We enhance by adding proper error messages, also disabling
the CPU port on the way down and moving dev_info() to
dev_dbg().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When removing a port from a VLAN we are just erasing the
member config for the VLAN, which is wrong: other ports
can be using it.
Just mask off the port and only zero out the rest of the
member config once ports using of the VLAN are removed
from it.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This implements the missing MTU setting for the RTL8366RB
switch.
Apart from supporting jumboframes, this rids us of annoying
boot messages like this:
realtek-smi switch: nonfatal error -95 setting MTU on port 0
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Registering our slave MDIO bus outside of the OF infrastructure is
necessary in order to avoid creating double references of the same
Device Tree nodes, however it is not sufficient to guarantee that the
MDIO bus diversion is used because of_phy_connect() will still resolve
to a valid PHY phandle and it will connect to the PHY using its parent
MDIO bus which is still the SF2 master MDIO bus. The reason for that is
because BCM7445 systems were already shipped with a Device Tree blob
looking like this (irrelevant parts omitted for simplicity):
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
phy-mode = "rgmii-txid";
phy-handle = <&phy0>;
reg = <1>;
label = "rgmii_1";
};
...
mdio@403c0 {
...
phy0: ethernet-phy@0 {
broken-turn-around;
device_type = "ethernet-phy";
max-speed = <0x3e8>;
reg = <0>;
compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22";
};
};
There is a hardware issue with chip revisions (Dx) that lead to the
development of the following commits:
461cd1b03e ("net: dsa: bcm_sf2: Register our slave MDIO bus")
536fab5bf5 ("net: dsa: bcm_sf2: Do not register slave MDIO bus with OF")
b8c6cd1d31 ("net: dsa: bcm_sf2: do not use indirect reads and writes for 7445E0")
There should have been an internal MDIO bus node created for the chip
revision (Dx) that suffers from this problem, but it did not happen back
then.
Had that happen, that we should have correctly parented phy@0 (bcm53125
below) as child node of the internal MDIO bus, but the production Device
Tree blob that was shipped with the firmware targeted the fixed version
of the chip, despite both the affected and corrected chips being shipped
into production.
The problem is that of_phy_connect() for port@1 will happily resolve the
'phy-handle' from the mdio@403c0 node, which bypasses the diversion
completely. This results in this double programming that the diversion
refers to and aims to avoid. In order to force of_phy_connect() to fail,
and have DSA call to dsa_slave_phy_connect(), we must deactivate
ethernet-phy@0 from mdio@403c0, and the best way to do that is by
removing the phandle property completely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
Whenever a port gets enabled/disabled, recalcultate the required switch
clock rate to make sure it always gets set to the expected rate
targeting our switch use case. This is only done for the BCM7445 switch
as there is no clocking profile available for BCM7278.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetch the corresponding clock resource and enable/disable it during
suspend/resume if and only if we have no ports defined for Wake-on-LAN.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to differentiate between the possible failure modes of
b53_switch_reset() by looking at the dmesg output.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows us to see which device the err or info messages are
referring to if we have multiple b53 compatible devices on a board.
As this removes the only pr_*() calls in this file we can drop the
definition of pr_fmt().
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLANs and PVIDs on the RTL8366 utilizes a "member
configuration" (MC) which is largely unexplained in the
code.
This set-up requires a special ordering: rtl8366_set_pvid()
must be called first, followed by rtl8366_set_vlan(),
else the MC will not be properly allocated. Relax this
by factoring out the code obtaining an MC and reuse
the helper in both rtl8366_set_pvid() and
rtl8366_set_vlan() so we remove this strict ordering
requirement.
In the process, add some better comments and debug prints
so people who read the code understand what is going on.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8366_set_vlan() and rtl8366_set_pvid() get invalid
VLANs tossed at it, especially VLAN0, something the hardware
and driver cannot handle. Check validity and bail out like
we do in the other callbacks.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building on platforms without device tree, e.g. amd64, W=1 gives
a warning about mv88e6xxx_mdio_external_match being unused. Replace
of_match_node() with of_device_is_compatible() to prevent this
warning.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the helper functions introduced by the newly added
Lynx PCS MDIO module in the Felix VSC9959 and Seville VSC9953.
Instead of representing the PCS as a phy_device, a mdio_device structure
will be passed to the Lynx module which is now actually implementing all
the PCS configuration and status reporting.
All code previously used for PCS monitoring and runtime configuration
is removed and replaced will calls to the Lynx PCS operations.
Tested on the following SERDES protocols of LS1028A: 0x7777
(2500Base-X), 0x85bb (QSGMII), 0x9999 (SGMII) and 0x13bb (USXGMII).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove 1000baseT_Half to advertise correct hardware capability in
phylink_validate() callback function.
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in mt7530.c by inserting of_node_put()
before the break and return statements.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in felix.c by inserting of_node_put()
before the return statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/dsa/sja1105/sja1105_main.c:3418:38: warning: address of
array 'match->compatible' will always evaluate to 'true'
[-Wpointer-bool-conversion]
for (match = sja1105_dt_ids; match->compatible; match++) {
~~~ ~~~~~~~^~~~~~~~~~
1 warning generated.
We should check the value of the first character in compatible to see if
it is empty or not. This matches how the rest of the tree iterates over
IDs.
Fixes: 0b0e299720 ("net: dsa: sja1105: use detected device id instead of DT one on mismatch")
Link: https://github.com/ClangBuiltLinux/linux/issues/1139
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analysis reports this problem
b53_common.c:1583:13: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ent.port &= ~BIT(port);
~~~~~~~~ ^
ent is set by a successful call to b53_arl_read(). Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.
So add -ETIMEDOUT to the switch statement. Because
b53_arl_op_wait() already prints out a message, do not add another
one.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return the VLAN table size through devlink as a simple parameter, we
do not support altering it at runtime:
devlink resource show mdio_bus/fixed-0:1f
mdio_bus/fixed-0:1f:
name VTU size 4096 occ 0 unit entry dpipe_tables none
and after configure a bridge with VLAN filtering:
devlink resource show mdio_bus/fixed-0:1f
mdio_bus/fixed-0:1f:
name VTU size 4096 occ 1 unit entry dpipe_tables none
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this is a mock-up driver with no real data path for now, but we
will have one at some point, enable VLANs while not filtering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig help text contains the phrase "the the" in the help
text. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we can detect the chip revision 100% at runtime, it is useful
to specify it in the device tree compatible string too, because
otherwise there would be no way to assess the correctness of device tree
bindings statically, without booting a board (only some switch versions
have internal RGMII delays and/or an SGMII port).
But for testing the P/Q/R/S support, what I have is a reworked board
with the SJA1105T replaced by a pin-compatible SJA1105Q, and I don't
want to keep a separate device tree blob just for this one-off board.
Since just the chip has been replaced, its RGMII delay setup is
inherently the same (meaning: delays added by the PHY on the slave
ports, and by PCB traces on the fixed-link CPU port).
For this board, I'd rather have the driver shout at me, but go ahead and
use what it found even if it doesn't match what it's been told is there.
[ 2.970826] sja1105 spi0.1: Device tree specifies chip SJA1105T but found SJA1105Q, please fix it!
[ 2.980010] sja1105 spi0.1: Probed switch chip: SJA1105Q
[ 3.005082] sja1105 spi0.1: Enabled switch tagging
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support DSA_LOOP_NUM_PORTS in the switch, do not tell the DSA
core to allocate up to DSA_MAX_PORTS which is nearly the double (6 vs.
11).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For now we simply store the port MTU into a per-port member.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for a mockup data path, move the
driver data structures to include/linux/dsa/loop.h such that we can
share them between net/dsa/ and drivers/net/dsa/ later on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate a 4K array of VLANs instead of limiting ourselves to just 5
which is arbitrary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PVID should be per-port, this is a preliminary change to support a
802.1Q data path in the driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current poll interval is enough to ensure that rising and falling
edge events are not lost for a 1 PPS signal with 50% duty cycle.
But when we deliver the events to user space, it will try to infer if
they were corresponding to a rising or to a falling edge (the kernel
driver doesn't know that either). User space will try to make that
inference based on the time at which the PPS master had emitted the
pulse (i.e. if it's a .0 time, it's rising edge, if it's .5 time, it's
falling edge).
But there is no in-kernel API for retrieving the precise timestamp
corresponding to a PPS master (aka perout) pulse. So user space has to
guess even that. It will read the PTP time on the PPS master right after
we've delivered the extts event, and declare that the PPS master time
was just the closest integer second, based on 2 thresholds (lower than
.25, or higher than .75, and ignore anything else).
Except that, if we poll for extts events (and our hardware doesn't
really help us, by not providing an interrupt), then there is a risk
that the poll period (and therefore the time at which the event is
delivered) might confuse user space.
Because we are always scheduling the next extts poll at
SJA1105_EXTTS_INTERVAL "from now" (that's the only thing that the
schedule_delayed_work() API gives us), it means that the start time of
the next delayed workqueue will always be shifted to the right a little
bit (shifted with the SPI access duration of this workqueue run).
In turn, because user space sees extts events that are non-periodic
compared to the PPS master's time, this means that it might start making
wrong guesses about rising/falling edge.
To understand the effect, here is the output of ts2phc currently. Notice
the 'src' timestamps of the 'SKIP extts' events, and how they have a
large wander. They keep increasing until the upper limit for the ignore
threshold (.75 seconds), after which the application starts ignoring the
_other_ edge.
ts2phc[26.624]: /dev/ptp3 SKIP extts index 0 at 21.449898912 src 21.657784518
ts2phc[27.133]: adding tstamp 21.949894240 to clock /dev/ptp3
ts2phc[27.133]: adding tstamp 22.000000000 to clock /dev/ptp1
ts2phc[27.133]: /dev/ptp3 offset 640 s2 freq +5112
ts2phc[27.636]: /dev/ptp3 SKIP extts index 0 at 22.449889360 src 22.669398022
ts2phc[28.140]: adding tstamp 22.949884376 to clock /dev/ptp3
ts2phc[28.140]: adding tstamp 23.000000000 to clock /dev/ptp1
ts2phc[28.140]: /dev/ptp3 offset 96 s2 freq +4760
ts2phc[28.644]: /dev/ptp3 SKIP extts index 0 at 23.449879504 src 23.677420422
ts2phc[29.153]: adding tstamp 23.949874704 to clock /dev/ptp3
ts2phc[29.153]: adding tstamp 24.000000000 to clock /dev/ptp1
ts2phc[29.153]: /dev/ptp3 offset -264 s2 freq +4429
ts2phc[29.656]: /dev/ptp3 SKIP extts index 0 at 24.449870008 src 24.689407238
ts2phc[30.160]: adding tstamp 24.949865376 to clock /dev/ptp3
ts2phc[30.160]: adding tstamp 25.000000000 to clock /dev/ptp1
ts2phc[30.160]: /dev/ptp3 offset -280 s2 freq +4334
ts2phc[30.664]: /dev/ptp3 SKIP extts index 0 at 25.449860760 src 25.697449926
ts2phc[31.168]: adding tstamp 25.949856176 to clock /dev/ptp3
ts2phc[31.168]: adding tstamp 26.000000000 to clock /dev/ptp1
ts2phc[31.168]: /dev/ptp3 offset -176 s2 freq +4354
ts2phc[31.672]: /dev/ptp3 SKIP extts index 0 at 26.449851584 src 26.705433606
ts2phc[32.180]: adding tstamp 26.949846992 to clock /dev/ptp3
ts2phc[32.180]: adding tstamp 27.000000000 to clock /dev/ptp1
ts2phc[32.180]: /dev/ptp3 offset -80 s2 freq +4397
ts2phc[32.684]: /dev/ptp3 SKIP extts index 0 at 27.449842384 src 27.717415110
ts2phc[33.192]: adding tstamp 27.949837768 to clock /dev/ptp3
ts2phc[33.192]: adding tstamp 28.000000000 to clock /dev/ptp1
ts2phc[33.192]: /dev/ptp3 offset 0 s2 freq +4453
ts2phc[33.696]: /dev/ptp3 SKIP extts index 0 at 28.449833128 src 28.729412902
ts2phc[34.200]: adding tstamp 28.949828472 to clock /dev/ptp3
ts2phc[34.200]: adding tstamp 29.000000000 to clock /dev/ptp1
ts2phc[34.200]: /dev/ptp3 offset 8 s2 freq +4461
ts2phc[34.704]: /dev/ptp3 SKIP extts index 0 at 29.449823816 src 29.737416038
ts2phc[35.208]: adding tstamp 29.949819152 to clock /dev/ptp3
ts2phc[35.208]: adding tstamp 30.000000000 to clock /dev/ptp1
ts2phc[35.208]: /dev/ptp3 offset -8 s2 freq +4447
ts2phc[35.712]: /dev/ptp3 SKIP extts index 0 at 30.449814496 src 30.745554982
ts2phc[36.216]: adding tstamp 30.949809840 to clock /dev/ptp3
ts2phc[36.216]: adding tstamp 31.000000000 to clock /dev/ptp1
ts2phc[36.216]: /dev/ptp3 offset -8 s2 freq +4445
ts2phc[36.468]: /dev/ptp3 SKIP extts index 0 at 31.449805184 src 31.501109446
ts2phc[36.972]: adding tstamp 31.949800536 to clock /dev/ptp3
ts2phc[36.972]: adding tstamp 32.000000000 to clock /dev/ptp1
ts2phc[36.972]: /dev/ptp3 offset -8 s2 freq +4442
ts2phc[37.480]: /dev/ptp3 SKIP extts index 0 at 32.449795896 src 32.513320070
ts2phc[37.984]: adding tstamp 32.949791248 to clock /dev/ptp3
ts2phc[37.984]: adding tstamp 33.000000000 to clock /dev/ptp1
ts2phc[37.984]: /dev/ptp3 offset 0 s2 freq +4448
Fix that by taking the following measures:
- Schedule the poll from a timer. Because we are really scheduling the
timer periodically, the extts events delivered to user space are
periodic too, and don't suffer from the "shift-to-the-right" effect.
- Increase the poll period to 6 times a second. This imposes a smaller
upper bound to the shift that can occur to the delivery time of extts
events, and makes user space (ts2phc) to always interpret correctly
which events should be skipped and which shouldn't.
- Move the SPI readout itself to the main PTP kernel thread, instead of
the generic workqueue. This is because the timer runs in atomic
context, but is also better than before, because if needed, we can
chrt & taskset this kernel thread, to ensure it gets enough priority
under load.
After this patch, one can notice that the wander is greatly reduced, and
that the latencies of one extts poll are not propagated to the next. The
'src' timestamp that is skipped is never larger than .65 seconds (which
means .15 seconds larger than the time at which the real event occurred
at, and .10 seconds smaller than the .75 upper threshold for ignoring
the falling edge):
ts2phc[40.076]: adding tstamp 34.949261296 to clock /dev/ptp3
ts2phc[40.076]: adding tstamp 35.000000000 to clock /dev/ptp1
ts2phc[40.076]: /dev/ptp3 offset 48 s2 freq +4631
ts2phc[40.568]: /dev/ptp3 SKIP extts index 0 at 35.449256496 src 35.595791078
ts2phc[41.064]: adding tstamp 35.949251744 to clock /dev/ptp3
ts2phc[41.064]: adding tstamp 36.000000000 to clock /dev/ptp1
ts2phc[41.064]: /dev/ptp3 offset -224 s2 freq +4374
ts2phc[41.552]: /dev/ptp3 SKIP extts index 0 at 36.449247088 src 36.579825574
ts2phc[42.044]: adding tstamp 36.949242456 to clock /dev/ptp3
ts2phc[42.044]: adding tstamp 37.000000000 to clock /dev/ptp1
ts2phc[42.044]: /dev/ptp3 offset -240 s2 freq +4290
ts2phc[42.536]: /dev/ptp3 SKIP extts index 0 at 37.449237848 src 37.563828774
ts2phc[43.028]: adding tstamp 37.949233264 to clock /dev/ptp3
ts2phc[43.028]: adding tstamp 38.000000000 to clock /dev/ptp1
ts2phc[43.028]: /dev/ptp3 offset -144 s2 freq +4314
ts2phc[43.520]: /dev/ptp3 SKIP extts index 0 at 38.449228656 src 38.547823238
ts2phc[44.012]: adding tstamp 38.949224048 to clock /dev/ptp3
ts2phc[44.012]: adding tstamp 39.000000000 to clock /dev/ptp1
ts2phc[44.012]: /dev/ptp3 offset -80 s2 freq +4335
ts2phc[44.508]: /dev/ptp3 SKIP extts index 0 at 39.449219432 src 39.535846118
ts2phc[44.996]: adding tstamp 39.949214816 to clock /dev/ptp3
ts2phc[44.996]: adding tstamp 40.000000000 to clock /dev/ptp1
ts2phc[44.996]: /dev/ptp3 offset -32 s2 freq +4359
ts2phc[45.488]: /dev/ptp3 SKIP extts index 0 at 40.449210192 src 40.515824678
ts2phc[45.980]: adding tstamp 40.949205568 to clock /dev/ptp3
ts2phc[45.980]: adding tstamp 41.000000000 to clock /dev/ptp1
ts2phc[45.980]: /dev/ptp3 offset 8 s2 freq +4390
ts2phc[46.636]: /dev/ptp3 SKIP extts index 0 at 41.449200928 src 41.664176902
ts2phc[47.132]: adding tstamp 41.949196288 to clock /dev/ptp3
ts2phc[47.132]: adding tstamp 42.000000000 to clock /dev/ptp1
ts2phc[47.132]: /dev/ptp3 offset 0 s2 freq +4384
ts2phc[47.620]: /dev/ptp3 SKIP extts index 0 at 42.449191656 src 42.648117190
ts2phc[48.112]: adding tstamp 42.949187016 to clock /dev/ptp3
ts2phc[48.112]: adding tstamp 43.000000000 to clock /dev/ptp1
ts2phc[48.112]: /dev/ptp3 offset 0 s2 freq +4384
ts2phc[48.604]: /dev/ptp3 SKIP extts index 0 at 43.449182384 src 43.632112582
ts2phc[49.100]: adding tstamp 43.949177736 to clock /dev/ptp3
ts2phc[49.100]: adding tstamp 44.000000000 to clock /dev/ptp1
ts2phc[49.100]: /dev/ptp3 offset -8 s2 freq +4376
ts2phc[49.588]: /dev/ptp3 SKIP extts index 0 at 44.449173096 src 44.616136774
ts2phc[50.080]: adding tstamp 44.949168464 to clock /dev/ptp3
ts2phc[50.080]: adding tstamp 45.000000000 to clock /dev/ptp1
ts2phc[50.080]: /dev/ptp3 offset 8 s2 freq +4390
ts2phc[50.572]: /dev/ptp3 SKIP extts index 0 at 45.449163816 src 45.600134662
ts2phc[51.064]: adding tstamp 45.949159160 to clock /dev/ptp3
ts2phc[51.064]: adding tstamp 46.000000000 to clock /dev/ptp1
ts2phc[51.064]: /dev/ptp3 offset -8 s2 freq +4376
ts2phc[51.556]: /dev/ptp3 SKIP extts index 0 at 46.449154528 src 46.584588550
ts2phc[52.048]: adding tstamp 46.949149896 to clock /dev/ptp3
ts2phc[52.048]: adding tstamp 47.000000000 to clock /dev/ptp1
ts2phc[52.048]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[52.540]: /dev/ptp3 SKIP extts index 0 at 47.449145256 src 47.568132198
ts2phc[53.032]: adding tstamp 47.949140616 to clock /dev/ptp3
ts2phc[53.032]: adding tstamp 48.000000000 to clock /dev/ptp1
ts2phc[53.032]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[53.524]: /dev/ptp3 SKIP extts index 0 at 48.449135968 src 48.552121446
ts2phc[54.016]: adding tstamp 48.949131320 to clock /dev/ptp3
ts2phc[54.016]: adding tstamp 49.000000000 to clock /dev/ptp1
ts2phc[54.016]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[54.512]: /dev/ptp3 SKIP extts index 0 at 49.449126680 src 49.540147014
ts2phc[55.000]: adding tstamp 49.949122040 to clock /dev/ptp3
ts2phc[55.000]: adding tstamp 50.000000000 to clock /dev/ptp1
ts2phc[55.000]: /dev/ptp3 offset 0 s2 freq +4382
ts2phc[55.492]: /dev/ptp3 SKIP extts index 0 at 50.449117400 src 50.520119078
ts2phc[55.988]: adding tstamp 50.949112768 to clock /dev/ptp3
ts2phc[55.988]: adding tstamp 51.000000000 to clock /dev/ptp1
ts2phc[55.988]: /dev/ptp3 offset 8 s2 freq +4390
ts2phc[56.476]: /dev/ptp3 SKIP extts index 0 at 51.449108120 src 51.504175910
ts2phc[57.132]: adding tstamp 51.949103480 to clock /dev/ptp3
ts2phc[57.132]: adding tstamp 52.000000000 to clock /dev/ptp1
ts2phc[57.132]: /dev/ptp3 offset 0 s2 freq +4384
ts2phc[57.624]: /dev/ptp3 SKIP extts index 0 at 52.449098840 src 52.651833574
ts2phc[58.116]: adding tstamp 52.949094200 to clock /dev/ptp3
ts2phc[58.116]: adding tstamp 53.000000000 to clock /dev/ptp1
ts2phc[58.116]: /dev/ptp3 offset 8 s2 freq +4392
ts2phc[58.612]: /dev/ptp3 SKIP extts index 0 at 53.449089560 src 53.639826918
ts2phc[59.100]: adding tstamp 53.949084920 to clock /dev/ptp3
ts2phc[59.100]: adding tstamp 54.000000000 to clock /dev/ptp1
ts2phc[59.100]: /dev/ptp3 offset 8 s2 freq +4394
ts2phc[59.592]: /dev/ptp3 SKIP extts index 0 at 54.449080272 src 54.619842278
ts2phc[60.084]: adding tstamp 54.949075624 to clock /dev/ptp3
ts2phc[60.084]: adding tstamp 55.000000000 to clock /dev/ptp1
ts2phc[60.084]: /dev/ptp3 offset 8 s2 freq +4397
ts2phc[60.576]: /dev/ptp3 SKIP extts index 0 at 55.449070968 src 55.603885542
ts2phc[61.068]: adding tstamp 55.949066312 to clock /dev/ptp3
ts2phc[61.068]: adding tstamp 56.000000000 to clock /dev/ptp1
ts2phc[61.068]: /dev/ptp3 offset 0 s2 freq +4391
ts2phc[61.560]: /dev/ptp3 SKIP extts index 0 at 56.449061680 src 56.587885798
ts2phc[62.052]: adding tstamp 56.949057032 to clock /dev/ptp3
ts2phc[62.052]: adding tstamp 57.000000000 to clock /dev/ptp1
ts2phc[62.052]: /dev/ptp3 offset -8 s2 freq +4383
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full 802.1q VLAN support to the qca8k, allowing the use of
vlan_filtering and more complicated bridging setups than allowed by
basic port VLAN support.
Tested with a number of untagged ports with separate VLANs and then a
trunk port with all the VLANs tagged on it.
v3:
- Pull QCA8K_PORT_VID_DEF changes into separate cleanup patch
- Reverse Christmas tree notation for variable definitions
- Use untagged instead of tagged for consistency
v2:
- Return sensible errnos on failure rather than -1 (rmk)
- Style cleanups based on Florian's feedback
- Silently allow VLAN 0 as device correctly treats this as no tag
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using a magic value of 1 when configuring the port VIDs add
a QCA8K_PORT_VID_DEF define and use that instead. Also fix up the
bitmask in the process; the top 4 bits are reserved so this wasn't a
problem, but only masking 12 bits is the correct approach.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alter the rtl8366_vlan_add() to call rtl8366_set_vlan()
inside the loop that goes over all VIDs since we now
properly support calling that function more than once.
Augment the loop to postincrement as this is more
intuitive.
The loop moved past the last VID but called
rtl8366_set_vlan() with the port number instead of
the VID, assuming a 1-to-1 correspondence between
ports and VIDs. This was also a bug.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366 would not handle adding new members (ports) to
a VLAN: the code assumed that ->port_vlan_add() was only
called once for a single port. When intializing the
switch with .configure_vlan_while_not_filtering set to
true, the function is called numerous times for adding
all ports to VLAN1, which was something the code could
not handle.
Alter rtl8366_set_vlan() to just |= new members and
untagged flags to 4k and MC VLAN table entries alike.
This makes it possible to just add new ports to a
VLAN.
Put in some helpful debug code that can be used to find
any further bugs here.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the chips in the mv88e6xxx family don't support jumbo
configuration per port. But they do have a chip-wide max frame size that
can be used. Use this to approximate the behaviour of configuring a port
based MTU.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6190 and MV88E6190X both support per port jumbo configuration
just like the other GE switches. Install the appropriate ops.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6097 chip does not support configuring jumbo frames. Prior to
commit 5f4366660d only the 6352, 6351, 6165 and 6320 chips configured
jumbo mode. The refactor accidentally added the function for the 6097.
Remove the erroneous function pointer assignment.
Fixes: 5f4366660d ("net: dsa: mv88e6xxx: Refactor setting of jumbo frames")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c61 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch has a single max frame size configuration register, so we
track the requested MTU for each port and apply the largest.
v2:
- Address review feedback from Vladimir Oltean
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If in-band negotiation or fixed-link modes are specified for a DSA
port, the DSA code will force the link down during initialisation. For
fixed-link mode, this is fine, as phylink will manage the link state.
However, for in-band mode, phylink expects the PCS to detect link,
which will not happen if the link is forced down.
There is a related issue that in in-band mode, the link could come up
while we are making configuration changes, so we should force the link
down prior to reconfiguring the interface mode.
This patch addresses both issues.
Fixes: 3be98b2d5f ("net: dsa: Down cpu/dsa ports phylink will control")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are USXGMII constants available, drop the old definitions
and reuse the generic ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the users of MSCC_OCELOT_SWITCH_LIB depend on REGMAP_MMIO was a
bad idea, since that symbol is not user-selectable. So we should have
kept a 'select REGMAP_MMIO'.
When we do that, we run into 2 more problems:
- By depending on GENERIC_PHY, we are causing a recursive dependency.
But it looks like GENERIC_PHY has no other dependencies, and other
drivers select it, so we can select it too:
drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15: symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22: symbol MSCC_OCELOT_SWITCH depends on GENERIC_PHY
drivers/phy/Kconfig:8: symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
drivers/phy/broadcom/Kconfig:41: symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
drivers/net/phy/Kconfig:13: symbol MDIO_BUS depends on MDIO_DEVICE
drivers/net/phy/Kconfig:6: symbol MDIO_DEVICE is selected by PHYLIB
drivers/net/phy/Kconfig:254: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25: symbol ARC_EMAC depends on OF_IRQ
- By depending on PHYLIB, we are causing a recursive dependency. PHYLIB
only has a single dependency, "depends on NETDEVICES", which we are
already depending on, so we can again hack our way into conformance by
turning the PHYLIB dependency into a select.
drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15: symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22: symbol MSCC_OCELOT_SWITCH depends on PHYLIB
drivers/net/phy/Kconfig:254: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25: symbol ARC_EMAC depends on OF_IRQ
Fixes: f4d0323bae ("net: mscc: ocelot: convert MSCC_OCELOT_SWITCH into a library")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is another switch from Vitesse / Microsemi / Microchip, that has
10 ports (8 external, 2 internal) and is integrated into the Freescale /
NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A,
except that this is a platform device and Felix is a PCI device, and it
doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus
using a phy_device abstraction for it (yes, it will be refactored to use
a raw mdio_device, like other phylink drivers do, but let's keep it like
that for now). But unlike Felix, the MDIO bus and the PCS are not from
the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in
Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it
is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it
would be difficult to reuse that driver (it doesn't even use regmap, and
it's less than 200 lines of code), so we hand-roll here some internal
MDIO bus accessors within seville_vsc9953.c, which serves the purpose of
driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of
SerDes protocol, so we need to do pre-validation of PHY mode from device
tree and not let phylink change it.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix is not actually meant to be a DSA driver only for the switch
inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi /
Microchip switches that are register-compatible with Ocelot and that are
using in DSA mode (with an NPI Ethernet port).
For the dsa_switch_ops exported by the felix driver to be generic enough
to be used by other non-PCI switches, we need to move the PCI-specific
probing to the low-level translation module felix_vsc9959.c. This way,
other switches can have their own probing functions, as platform devices
or otherwise.
This patch also removes the "Felix instance table", which did not stand
the test of time and is unnecessary at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell Switches support jumbo packages. So implement the
callbacks needed for changing the MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This activates the support to use the CPU tag to properly
direct ingress traffic to the right port.
Bit 15 in register RTL8368RB_CPU_CTRL_REG can be set to
1 to disable the insertion of the CPU tag which is what
the code currently does. The bit 15 define calls this
setting RTL8368RB_CPU_INSTAG which is confusing since the
inverse meaning is implied: programmers may think that
setting this bit to 1 will *enable* inserting the tag
rather than disabling it, so rename this setting in
bit 15 to RTL8368RB_CPU_NO_TAG which is more to the
point.
After this e.g. ping works out-of-the-box with the
RTL8366RB.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a number of error conditions that can lead to the driver not
probing successfully, move the print when we are sure
dsa_register_switch() has suceeded. This avoids repeated prints in case
of probe deferral for instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments before struct vsc73xx_platform and struct vsc73xx_spi use
kerneldoc format, but then fail to document the members of these
structures. All the structure members are self evident, and the driver
has not other kerneldoc comments, so change these to plain comments to
avoid warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since lan9303_adjust_link() is a void function, there is no option to
return an error. So just remove the variable and lets any errors be
discarded.
Cc: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oddly, GENMASK() requires signed bit numbers, so that it can compare
them for < 0. If passed an unsigned type, we get warnings about the
test never being true.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oddly, GENMASK() requires signed bit numbers, so that it can compare
them for < 0. If passed an unsigned type, we get warnings about the
test never being true. There is no danger of overflow here, udf is
always a u8, so there is plenty of space when expanding to an int.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A __be16 variable should be initialised with a __be16 value. So add a
htons(). In this case it is pointless, given the value being assigned
is 0xffff, but it stops sparse from warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
leX_to_cpu() expects to be passed an __leX type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't act on any errors reading registers while handling watchdog
interrupt. Since this is an interrupt handler, we cannot return such
errors. So just remove the variable.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow spec member vlan_tci is in network order. Hence comparisons
should be made again network order values.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oddly, GENMASK() requires signed bit numbers, so that it can compare
them for < 0. If passed an unsigned type, we get warnings about the
test never being true.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink now requires that parameters established through
auto-negotiation be written into the MAC at the time of the
mac_link_up() callback. In the case of felix, that means taking the port
out of reset, setting the correct timers for PAUSE frames, and
enabling/disabling TX flow control.
This patch also splits the inband and noinband configuration of the
vsc9959 PCS (currently found in a function called "init") into 2
different functions, which have a nomenclature closer to phylink:
"config", for inband setup, and "link_up", for noinband (forced) setup.
This is necessary as a preparation step for giving up control of the PCS
to phylink, which will be done in further patch series.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylink uses the .mac_an_restart method to offer the user an
implementation of the "ethtool -r" behavior, when the media-side auto
negotiation can be restarted by the local MAC PCS. This is the case for
fiber modes 1000Base-X and 2500Base-X (IEEE clause 37) that don't have
an Ethernet PHY connected locally, and the media is connected to the MAC
PCS directly.
On the other hand, the Cisco SGMII and USXGMII standards also have an
auto negotiation mechanism based on IEEE 802.3 clause 37 (their
respective specs require a MAC PCS and a PHY PCS to implement the same
state machine, which is described in IEEE 802.3 "Auto-Negotiation Figure
37-6"), so the ability to restart auto-negotiation is intrinsically
symmetrical (the MAC PCS can do it too).
However, it appears that not all SGMII/USXGMII PHYs have logic to
restart the MDI-side auto-negotiation process when they detect a
transition of the SGMII link from data mode to configuration mode.
Some do (VSC8234) and some don't (AR8033, MV88E1111). IEEE and/or Cisco
specification wordings to not help to prove whether propagating the "AN
restart" event from MII side ("mr_restart_an") to MDI side
("mr_restart_negotiation") is required behavior - neither of them
specifies any mandatory interaction between the clause 37 AN state
machine from Figure 37-6 and the clause 28 AN state machine from Figure
28-18.
Therefore, even if a certain behavior could be proven as being required,
real-life SGMII/USXGMII PHYs are inconsistent enough that a clause 37 AN
restart cannot be used by phylink to reliably trigger a media-side
renegotiation, when the user requests it via ethtool.
The only remaining use that the .mac_an_restart callback might possibly
have, given what we know now, is to implement some silicon quirks, but
so far that has proven to not be necessary.
So remove this code for now, since it never gets called and we don't
foresee any circumstance in which it might be, either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->speed holds a value of 10, 100, 1000 or 2500, but
SYS_MAC_FC_CFG_FC_LINK_SPEED expects a value in the range 0, 1, 2 or 3.
So set the correct speed encoding into this register.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In VSC9959, the PCS is the one who performs rate adaptation (symbol
duplication) to the speed negotiated by the PHY. The MAC is unaware of
that and must remain configured for gigabit. If it is configured at
OCELOT_SPEED_10 or OCELOT_SPEED_100, it'll start transmitting PAUSE
frames out of control and never recover, _even if_ we then reconfigure
it at OCELOT_SPEED_1000 afterwards.
This patch fixes a bug that luckily did not have any functional impact.
We were writing 10, 100, 1000 etc into this 2-bit field in
DEV_CLOCK_CFG, but the hardware expects values in the range 0, 1, 2, 3.
So all speed values were getting truncated to 0, which is
OCELOT_SPEED_2500, and which also appears to be fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ping tested:
[ 11.808455] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.816497] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x4
[ 18.844591] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 22.048337] mscc_felix 0000:00:00.5 swp0: Link is Up - 100Mbps/Half - flow control off
[root@LS1028ARDB ~] # ip addr add 192.168.1.1/24 dev swp0
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 0.383/0.611/1.051 ms
[root@LS1028ARDB ~] # ethtool -s swp0 advertise 0x10
[ 355.637747] mscc_felix 0000:00:00.5 swp0: Link is Down
[ 358.788034] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Half - flow control off
[root@LS1028ARDB ~] # ping 192.168.1.2
PING 192.168.1.2 (192.168.1.2): 56 data bytes
(...)
^C
--- 192.168.1.2 ping statistics ---
16 packets transmitted, 16 packets received, 0% packet loss
round-trip min/avg/max = 0.301/0.384/1.138 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver appears to write to BMCR_SPEED and BMCR_DUPLEX, fields which
are read-only, since they are actually configured through the
vendor-specific IF_MODE (0x14) register.
But the reason we're writing back the read-only values of MII_BMCR is to
alter these writable fields:
BMCR_RESET
BMCR_LOOPBACK
BMCR_ANENABLE
BMCR_PDOWN
BMCR_ISOLATE
BMCR_ANRESTART
In particular, the only field which is really relevant to this driver is
BMCR_ANENABLE. Clarify that intention by spelling it out, using
phy_set_bits and phy_clear_bits.
The driver also made a few writes to BMCR_RESET and BMCR_ANRESTART which
are unnecessary and may temporarily disrupt the link to the PHY. Remove
them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Private structure members live_ports, on_ports, rx_ports, tx_ports are
initialized but not used anywhere. Let's remove them.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA subsystem moved to phylink and adjust_link() became deprecated in
the process. This patch removes adjust_link from the KSZ DSA switches and
adds phylink_mac_link_up() and phylink_mac_link_down().
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of ports is incorrectly set to the maximum available for a DSA
switch. Even if the extra ports are not used, this causes some functions
to be called later, like port_disable() and port_stp_state_set(). If the
driver doesn't check the port index, it will end up modifying unknown
registers.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9893 3-Port Gigabit Ethernet Switch can be controlled via SPI,
I²C or MDIO (very limited and not supported by this driver). While there
is already a compatible entry for the SPI bus, it was missing for I²C.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 only appears to support pause modes on RGMII interfaces (the
enable bits are in the RGMII control register.) Setup the pause modes
for RGMII connections.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the bcm_sf2 to use the finalised speed and duplex in its
mac_link_up() call rather than the parameters in mac_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
state->link has never been valid in mac_config() implementations -
while it may be correct in some calls, it is not true that it can be
relied upon.
Fix bcm_sf2 to use the correct method of handling forced link status.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the B53 driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config(). This is
just a matter of moving the call to b53_force_port_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the b53_force_port_config() pause argument, which is based on
phylink's MLO_PAUSE_* definitions, to use a pair of booleans. This
will allow us to move b53_force_port_config() from
b53_phylink_mac_config() to b53_phylink_mac_link_up().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'tcfp_burst' with TICK factor, driver side always need to recover
it to the original value, this patch moves the generic calculation and
recover to the 'burst' original value before offloading to device driver.
Signed-off-by: Po Liu <po.liu@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105_gating_cfg_time_to_interval function does this, as per the
comments:
/* The gate entries contain absolute times in their e->interval field. Convert
* that to proper intervals (i.e. "0, 5, 10, 15" to "5, 5, 5, 5").
*/
To perform that task, it iterates over gating_cfg->entries, at each step
updating the interval of the _previous_ entry. So one interval remains
to be updated at the end of the loop: the last one (since it isn't
"prev" for anyone else).
But there was an erroneous check, that the last element's interval
should not be updated if it's also the only element. I'm not quite sure
why that check was there, but it's clearly incorrect, as a tc-gate
schedule with a single element would get an e->interval of zero,
regardless of the duration requested by the user. The switch wouldn't
even consider this configuration as valid: it will just drop all traffic
that matches the rule.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tas_data->enabled would remain true even after deleting all
tc-gate rules from the switch ports, which would cause the
sja1105_tas_state_machine to get unnecessarily scheduled.
Also, if there were any errors which would prevent the hardware from
enabling the gating schedule, the sja1105_tas_state_machine would
continuously detect and print that, spamming the kernel log, even if the
rules were subsequently deleted.
The rules themselves are _not_ active, because sja1105_init_scheduling
does enough of a job to not install the gating schedule in the static
config. But the virtual link rules themselves are still present.
So call the functions that remove the tc-gate configuration from
priv->tas_data.gating_cfg, so that tas_data->enabled can be set to
false, and sja1105_tas_state_machine will stop from being scheduled.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sja1105_compose_gating_subschedule is not prepared to be
called for the case where we want to recompute the global tc-gate
configuration after we've deleted those actions on a port.
After deleting the tc-gate actions on the last port, max_cycle_time
would become zero, and that would incorrectly prevent
sja1105_free_gating_config from getting called.
So move the freeing function above the check for the need to apply a new
configuration.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that sja1105_compose_gating_subschedule must also be called
from sja1105_vl_delete, to recalculate the overall tc-gate
configuration. Currently this is not possible without introducing a
forward declaration. So move the function at the top of the file, along
with its dependencies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the ar9331 DSA driver to use the finalised link parameters in
mac_link_up() rather than the parameters in mac_config().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the mdb hooks in felix and exports the mdb functions from
ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since struct sja1105_private only holds a const pointer to one of these
structures based on device tree compatible string, the structures
themselves can be made const.
Also add an empty line between each structure definition, to appease
checkpatch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-chip instantiations of struct sja1105_table_ops and struct
sja1105_dynamic_table_ops can be made constant, so do that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse is complaining and giving the following warning message:
'Using plain integer as NULL pointer'.
This is not what's going on, instead {0} is used as a zero initializer
for the structure members, to indicate that the particular chip revision
does not support those particular config tables.
But since the config tables are declared globally, the unpopulated
elements are zero-initialized anyway. So, to make sparse shut up, let's
remove the zero initializers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the handling of the SGMII interface on the QCA8K
devices. Previously the driver did no configuration of the port, even if
it was selected. We now configure it up in the appropriate
PHY/MAC/Base-X mode depending on what phylink tells us we are connected
to and ensure it is enabled.
Tested with a device where the CPU connection is RGMII (i.e. the common
current use case) + one where the CPU connection is SGMII. I don't have
any devices where the SGMII interface is brought out to something other
than the CPU.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver to use the new PHYLINK callbacks, removing the
legacy adjust_link callback.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide the CONFIG_MSCC_OCELOT_SWITCH option from users. It is meant to be
only a hardware library which is selected by the drivers that use it
(ocelot, felix).
Since it is "selected" from Kconfig, all its dependencies are manually
transferred to the driver that selects it. This is because "select" in
Kconfig language is a bit of a mess, and doesn't handle dependencies of
selected options quite right.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: dfacc5a23e ("net: dsa: sja1105: support flow-based redirection via virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This shouldn't be there.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't actually described clearly at all in UM10944.pdf, but on TX of
a management frame (such as PTP), this needs to happen:
- The destination MAC address (i.e. 01-80-c2-00-00-0e), along with the
desired destination port, need to be installed in one of the 4
management slots of the switch, over SPI.
- The host can poll over SPI for that management slot's ENFPORT field.
That gets unset when the switch has matched the slot to the frame.
And therein lies the problem. ENFPORT does not mean that the packet has
been transmitted. Just that it has been received over the CPU port, and
that the mgmt slot is yet again available.
This is relevant because of what we are doing in sja1105_ptp_txtstamp_skb,
which is called right after sja1105_mgmt_xmit. We are in a hard
real-time deadline, since the hardware only gives us 24 bits of TX
timestamp, so we need to read the full PTP clock to reconstruct it.
Because we're in a hurry (in an attempt to make sure that we have a full
64-bit PTP time which is as close as possible to the actual transmission
time of the frame, to avoid 24-bit wraparounds), first we read the PTP
clock, then we poll for the TX timestamp to become available.
But of course, we don't know for sure that the frame has been
transmitted when we read the full PTP clock. We had assumed that ENFPORT
means it has, but the assumption is incorrect. And while in most
real-life scenarios this has never been caught due to software delays,
nowhere is this fact more obvious than with a tc-taprio offload, where
PTP traffic gets a small timeslot very rarely (example: 1 packet per 10
ms). In that case, we will be reading the PTP clock for timestamp
reconstruction too early (before the packet has been transmitted), and
this renders the reconstruction procedure incorrect (see the assumptions
described in the comments found on function sja1105_tstamp_reconstruct).
So the PTP TX timestamps will be off by 1<<24 clock ticks, or 135 ms
(1 tick is 8 ns).
So fix this case of premature optimization by simply reordering the
sja1105_ptpegr_ts_poll and the sja1105_ptpclkval_read function calls. It
turns out that in practice, the 135 ms hard deadline for PTP timestamp
wraparound is not so hard, since even the most bandwidth-intensive PTP
profiles, such as 802.1AS-2011, have a sync frame interval of 125 ms.
So if we couldn't deliver a timestamp in 135 ms (which we can), we're
toast and have much bigger problems anyway.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
While trying to use the lantiq_gswip driver on one of my boards I made
a mistake when specifying the phy-mode (because the out-of-tree driver
wants phy-mode "gmii" or "mii" for the internal PHYs). In this case the
following error is printed multiple times:
Unsupported interface: 3
While it gives at least a hint at what may be wrong it is not very user
friendly. Print the human readable phy-mode and also which port is
configured incorrectly (this hardware supports ports 0..6) to improve
the cases where someone made a mistake.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer C compilers are complaining about the fact that there are no
function prototypes in sja1105_vl.c for the non-static functions.
Give them what they want.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dynamic configuration interface for the General Params and the L2
Lookup Params tables was copy-pasted between E/T devices and P/Q/R/S
devices. Nonetheless, these interfaces are bitwise different.
The driver is using dynamic reconfiguration of the General Parameters
table for the port mirroring feature, which was therefore broken on
P/Q/R/S.
Note that this patch can't be backported easily very far to stable trees
(since it conflicts with some other development done since the
introduction of the driver). So the Fixes: tag is purely informational.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer compilers complain with W=1 builds that there are non-static
functions defined in sja1105_static_config.c that don't have a
prototype, because their prototype is defined in sja1105.h which this
translation unit does not include.
I don't entirely understand what is the point of these warnings, since
in principle there's nothing wrong with that. But let's move the
prototypes to a header file that _is_ included by
sja1105_static_config.c, since that will make these warnings go away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be there 2 switches spi/spi2.0 and spi/spi2.1 in a cross-chip setup,
both under the same VLAN-filtering bridge, both in the
SJA1105_VLAN_BEST_EFFORT state.
If we try to change the VLAN state of one of the switches (to
SJA1105_VLAN_FILTERING_FULL) we get the following error:
devlink dev param set spi/spi2.1 name best_effort_vlan_filtering value
false cmode runtime
[ 38.325683] sja1105 spi2.1: Not allowed to overcommit frame memory.
L2 memory partitions and VL memory partitions share the
same space. The sum of all 16 memory partitions is not
allowed to be larger than 929 128-byte blocks (or 910
with retagging). Please adjust
l2-forwarding-parameters-table.part_spc and/or
vl-forwarding-parameters-table.partspc.
[ 38.356803] sja1105 spi2.1: Invalid config, cannot upload
This is because the spi/spi2.1 switch doesn't support tagging anymore in
the SJA1105_VLAN_FILTERING_FULL state, so it doesn't need to have any
retagging rules defined. Great, so it can use more frame memory
(retagging consumes extra memory).
But the built-in low-level static config checker from the sja1105 driver
says "not so fast, you've increased the frame memory to non-retagging
values, but you still kept the retagging rules in the static config".
So we need to rebuild the VLAN table immediately before re-uploading the
static config, operation which will take care, based on the new VLAN
state, of removing the retagging rules.
Fixes: 3f01c91aab ("net: dsa: sja1105: implement VLAN retagging for dsa_8021q sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SJA1105, being AVB/TSN switches, provide hardware assist for the
Credit-Based Shaper as described in the IEEE 8021Q-2018 document.
First generation has 10 shapers, freely assignable to any of the 4
external ports and 8 traffic classes, and second generation has 16
shapers.
The Credit-Based Shaper tables are accessed through the dynamic
reconfiguration interface, so we have to restore them manually after a
switch reset. The tables are backed up by the static config only on
P/Q/R/S, and we don't want to add custom code only for that family,
since the procedure that is in place now works for both.
Tested with the following commands:
data_rate_kbps=67000
port_transmit_rate_kbps=1000000
idleslope=$data_rate_kbps
sendslope=$(($idleslope - $port_transmit_rate_kbps))
locredit=$((-0x80000000))
hicredit=$((0x7fffffff))
tc qdisc add dev swp2 root handle 1: mqprio hw 0 num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7
tc qdisc replace dev swp2 parent 1:1 cbs \
idleslope $idleslope \
sendslope $sendslope \
hicredit $hicredit \
locredit $locredit \
offload 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in other commits before (b9cd75e668 and 87b0f983f6),
ocelot switches have a single egress-untagged VLAN per port, and the
driver would deny adding a second one while an egress-untagged VLAN
already exists.
But on the CPU port (where the VLAN configuration is implicit, because
there is no net device for the bridge to control), the DSA core attempts
to add a VLAN using the same flags as were used for the front-panel
port. This would make adding any untagged VLAN fail due to the CPU port
rejecting the configuration:
bridge vlan add dev swp0 vid 100 pvid untagged
[ 1865.854253] mscc_felix 0000:00:00.5: Port already has a native VLAN: 1
[ 1865.860824] mscc_felix 0000:00:00.5: Failed to add VLAN 100 to port 5: -16
(note that port 5 is the CPU port and not the front-panel swp0).
So this hardware will send all VLANs as tagged towards the CPU.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot core library is written with the idea in mind that the VLAN
table is populated by the bridge. Otherwise, not even a sane default
pvid is provided: in standalone mode, the default pvid is 0, and the
core expects the bridge layer to change it to 1.
So without this patch, the VLAN table is completely empty at the end of
the commands below, and traffic is broken as a result:
ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up
for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do
ip link set dev $eth master br0
ip link set dev $eth up
done
ip link set dev br0 type bridge vlan_filtering 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable new_pvid is being assigned with a value that is never read,
the following if statement updates new_pvid with a new value in both
of the if paths. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of devm_ioremap_resource(), either accidentally
or by wrong assumption, is writing back derived resource data
to global static resource initialization tables that should
have been constant. Meaning that after it computes the final
physical start address it saves the address for no reason
in the static tables. This doesn't affect the first driver
probing after reboot, but it breaks consecutive driver reloads
(i.e. driver unbind & bind) because the initialization tables
no longer have the correct initial values. So the next probe()
will map the device registers to wrong physical addresses,
causing ARM SError async exceptions.
This patch fixes all of the above.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA to add VLAN entries even if VLAN filtering is disabled, so
enabling it will not block the traffic of existent ports in the bridge
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently burst is clamping on rate and not burst, the assignment
of burst from the clamping discards the previous assignment of burst.
This looks like a cut-n-paste error from the previous clamping
calculation on ramp. Fix this by replacing ramp with burst.
Addresses-Coverity: ("Unused value")
Fixes: 0fbabf875d ("net: dsa: felix: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 hardware support the Credit Based Shaper(CBS) which part
of the IEEE-802.1Qav. This patch support sch_cbs set for VSC9959.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot VSC9959 switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. This patch add support for TAS configuration
on egress port of VSC9959 switch.
Felix driver is an instance of Ocelot family, with a DSA front-end. The
patch uses tc taprio hardware offload to setup TAS set function on felix
driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the default QoS Classification based on PCP and DEI of vlan tag,
after that, frames can be Classified to different Qos based on PCP tag.
If there is no vlan tag or vlan ignored, use port default Qos.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the delta commit procedure for VLANs with additional logic for
treating bridge_vlans in the newly introduced operating mode,
SJA1105_VLAN_BEST_EFFORT.
For every bridge VLAN on every user port, a sub-VLAN index is calculated
and retagging rules are installed towards a dsa_8021q rx_vid that
encodes that sub-VLAN index. This way, the tagger can identify the
original VLANs.
Extra care is taken for VLANs to still work as intended in cross-chip
scenarios. Retagging may have unintended consequences for these because
a sub-VLAN encoding that works for the CPU does not make any sense for a
front-panel port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 different features that require some reserved frame memory
space: VLAN retagging and virtual links. Create a central function that
modifies the static config and ensures frame memory is never
overcommitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Retagging Table is an optional feature that allows the switch to
match frames against a {ingress port, egress port, vid} rule and change
their VLAN ID. The retagged frames are by default clones of the original
ones (since the hardware-foreseen use case was to mirror traffic for
debugging purposes and to tag it with a special VLAN for this purpose),
but we can force the original frames to be dropped by removing the
pre-retagging VLAN from the port membership list of the egress port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This devlink parameter enables the handling of DSA tags when enslaved to
a bridge with vlan_filtering=1. There are very good reasons to want
this, but there are also very good reasons for not enabling it by
default. So a devlink param named best_effort_vlan_filtering, currently
driver-specific and exported only by sja1105, is used to configure this.
In practice, this is perhaps the way that most users are going to use
the switch in. It assumes that no more than 7 VLANs are needed per port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a subvlan_map as part of each port's tagger private structure.
This keeps reverse mappings of bridge-to-dsa_8021q VLAN retagging rules.
Note that as of this patch, this piece of code is never engaged, due to
the fact that the driver hasn't installed any retagging rule, so we'll
always see packets with a subvlan code of 0 (untagged).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In VLAN-unaware mode, sja1105 uses VLAN tags with a custom TPID of
0xdadb. While in the yet-to-be introduced best_effort_vlan_filtering
mode, it needs to work with normal VLAN TPID values.
A complication arises when we must transmit a VLAN-tagged packet to the
switch when it's in VLAN-aware mode. We need to construct a packet with
2 VLAN tags, and the switch will use the outer header for routing and
pop it on egress. But sadly, here the 2 hardware generations don't
behave the same:
- E/T switches won't pop an ETH_P_8021AD tag on egress, it seems
(packets will remain double-tagged).
- P/Q/R/S switches will drop a packet with 2 ETH_P_8021Q tags (it looks
like it tries to prevent VLAN hopping).
But looks like the reverse is also true:
- E/T switches have no problem popping the outer tag from packets with
2 ETH_P_8021Q tags.
- P/Q/R/S will have no problem popping a single tag even if that is
ETH_P_8021AD.
So it is clear that if we want the hardware to work with dsa_8021q
tagging in VLAN-aware mode, we need to send different TPIDs depending on
revision. Keep that information in priv->info->qinq_tpid.
The per-port tagger structure will hold an xmit_tpid value that depends
not only upon the qinq_tpid, but also upon the VLAN awareness state
itself (in case we must transmit using 0xdadb).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering is a global property for sja1105, and that means that we
rely on the DSA core to not call us more than once.
But we need to introduce some per-port state for the tagger, namely the
xmit_tpid, and the best place to do that is where the xmit_tpid changes,
namely in sja1105_vlan_filtering. So at the moment, exit early from the
function to avoid unnecessarily resetting the switch for each port call.
Then we'll change the xmit_tpid prior to the early exit in the next
patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the DSA core call our .port_vlan_add methods every time the bridge
layer requests so. We will deal internally with saving/restoring VLANs
depending on our VLAN awareness state.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Managing the VLAN table that is present in hardware will become very
difficult once we add a third operating state
(best_effort_vlan_filtering). That is because correct cleanup (not too
little, not too much) becomes virtually impossible, when VLANs can be
added from the bridge layer, from dsa_8021q for basic tagging, for
cross-chip bridging, as well as retagging rules for sub-VLANs and
cross-chip sub-VLANs. So we need to rethink VLAN interaction with the
switch in a more scalable way.
In preparation for that, use the priv->expect_dsa_8021q boolean to
classify any VLAN request received through .port_vlan_add or
.port_vlan_del towards either one of 2 internal lists: bridge VLANs and
dsa_8021q VLANs.
Then, implement a central sja1105_build_vlan_table method that creates a
VLAN configuration from scratch based on the 2 lists of VLANs kept by
the driver, and based on the VLAN awareness state. Currently, if we are
VLAN-unaware, install the dsa_8021q VLANs, otherwise the bridge VLANs.
Then, implement a delta commit procedure that identifies which VLANs
from this new configuration are actually different from the config
previously committed to hardware. We apply the delta through the dynamic
configuration interface (we don't reset the switch). The result is that
the hardware should see the exact sequence of operations as before this
patch.
This also helps remove the "br" argument passed to
dsa_8021q_crosschip_bridge_join, which it was only using to figure out
whether it should commit the configuration back to us or not, based on
the VLAN awareness state of the bridge. We can simplify that, by always
allowing those VLANs inside of our dsa_8021q_vlans list, and committing
those to hardware when necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment, this can never happen. The 2 modes that we operate in do
not permit that:
- SJA1105_VLAN_UNAWARE: we are guarded from bridge VLANs added by the
user by the DSA core. We will later lift this restriction by setting
ds->vlan_bridge_vtu = true, and that is where we'll need it.
- SJA1105_VLAN_FILTERING_FULL: in this mode, dsa_8021q configuration is
disabled. So the user is free to add these VLANs in the 1024-3071
range.
The reason for the patch is that we'll introduce a third VLAN awareness
state, where both dsa_8021q as well as the bridge are going to call our
.port_vlan_add and .port_vlan_del methods.
For that, we need a good way to discriminate between the 2. The easiest
(and less intrusive way for upper layers) is to recognize the fact that
dsa_8021q configurations are always driven by our driver - we _know_
when a .port_vlan_add method will be called from dsa_8021q because _we_
initiated it.
So introduce an expect_dsa_8021q boolean which is only used, at the
moment, for blacklisting VLANs in range 1024-3071 in the modes when
dsa_8021q is active.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soon we'll add a third operating mode to the driver. Introduce a
vlan_state to make things more easy to manage, and use it where
applicable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sja1105 uses dsa_8021q for DSA tagging, a format which is VLAN at heart
and which is compatible with cascading. A complete description of this
tagging format is in net/dsa/tag_8021q.c, but a quick summary is that
each external-facing port tags incoming frames with a unique pvid, and
this special VLAN is transmitted as tagged towards the inside of the
system, and as untagged towards the exterior. The tag encodes the switch
id and the source port index.
This means that cross-chip bridging for dsa_8021q only entails adding
the dsa_8021q pvids of one switch to the RX filter of the other
switches. Everything else falls naturally into place, as long as the
bottom-end of ports (the leaves in the tree) is comprised exclusively of
dsa_8021q-compatible (i.e. sja1105 switches). Otherwise, there would be
a chance that a front-panel switch transmits a packet tagged with a
dsa_8021q header, header which it wouldn't be able to remove, and which
would hence "leak" out.
The only use case I tested (due to lack of board availability) was when
the sja1105 switches are part of disjoint trees (however, this doesn't
change the fact that multiple sja1105 switches still need unique switch
identifiers in such a system). But in principle, even "true" single-tree
setups (with DSA links) should work just as fine, except for a small
change which I can't test: dsa_towards_port should be used instead of
dsa_upstream_port (I made the assumption that the routing port that any
sja1105 should use towards its neighbours is the CPU port. That might
not hold true in other setups).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One way of utilizing DSA is by cascading switches which do not all have
compatible taggers. Consider the following real-life topology:
+---------------------------------------------------------------+
| LS1028A |
| +------------------------------+ |
| | DSA master for Felix | |
| |(internal ENETC port 2: eno2))| |
| +------------+------------------------------+-------------+ |
| | Felix embedded L2 switch | |
| | | |
| | +--------------+ +--------------+ +--------------+ | |
| | |DSA master for| |DSA master for| |DSA master for| | |
| | | SJA1105 1 | | SJA1105 2 | | SJA1105 3 | | |
| | |(Felix port 1)| |(Felix port 2)| |(Felix port 3)| | |
+--+-+--------------+---+--------------+---+--------------+--+--+
+-----------------------+ +-----------------------+ +-----------------------+
| SJA1105 switch 1 | | SJA1105 switch 2 | | SJA1105 switch 3 |
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
|sw1p0|sw1p1|sw1p2|sw1p3| |sw2p0|sw2p1|sw2p2|sw2p3| |sw3p0|sw3p1|sw3p2|sw3p3|
+-----+-----+-----+-----+ +-----+-----+-----+-----+ +-----+-----+-----+-----+
The above can be described in the device tree as follows (obviously not
complete):
mscc_felix {
dsa,member = <0 0>;
ports {
port@4 {
ethernet = <&enetc_port2>;
};
};
};
sja1105_switch1 {
dsa,member = <1 1>;
ports {
port@4 {
ethernet = <&mscc_felix_port1>;
};
};
};
sja1105_switch2 {
dsa,member = <2 2>;
ports {
port@4 {
ethernet = <&mscc_felix_port2>;
};
};
};
sja1105_switch3 {
dsa,member = <3 3>;
ports {
port@4 {
ethernet = <&mscc_felix_port3>;
};
};
};
Basically we instantiate one DSA switch tree for every hardware switch
in the system, but we still give them globally unique switch IDs (will
come back to that later). Having 3 disjoint switch trees makes the
tagger drivers "just work", because net devices are registered for the
3 Felix DSA master ports, and they are also DSA slave ports to the ENETC
port. So packets received on the ENETC port are stripped of their
stacked DSA tags one by one.
Currently, hardware bridging between ports on the same sja1105 chip is
possible, but switching between sja1105 ports on different chips is
handled by the software bridge. This is fine, but we can do better.
In fact, the dsa_8021q tag used by sja1105 is compatible with cascading.
In other words, a sja1105 switch can correctly parse and route a packet
containing a dsa_8021q tag. So if we could enable hardware bridging on
the Felix DSA master ports, cross-chip bridging could be completely
offloaded.
Such as system would be used as follows:
ip link add dev br0 type bridge && ip link set dev br0 up
for port in sw0p0 sw0p1 sw0p2 sw0p3 \
sw1p0 sw1p1 sw1p2 sw1p3 \
sw2p0 sw2p1 sw2p2 sw2p3; do
ip link set dev $port master br0
done
The above makes switching between ports on the same row be performed in
hardware, and between ports on different rows in software. Now assume
the Felix switch ports are called swp0, swp1, swp2. By running the
following extra commands:
ip link add dev br1 type bridge && ip link set dev br1 up
for port in swp0 swp1 swp2; do
ip link set dev $port master br1
done
the CPU no longer sees packets which traverse sja1105 switch boundaries
and can be forwarded directly by Felix. The br1 bridge would not be used
for any sort of traffic termination.
For this to work, we need to give drivers an opportunity to listen for
bridging events on DSA trees other than their own, and pass that other
tree index as argument. I have made the assumption, for the moment, that
the other existing DSA notifiers don't need to be broadcast to other
trees. That assumption might turn out to be incorrect. But in the
meantime, introduce a dsa_broadcast function, similar in purpose to
dsa_port_notify, which is used only by the bridging notifiers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a soft dependency against dsa_loop_bdinfo.ko which sets up the
MDIO device registration, since there are no symbols referenced by
dsa_loop.ko, there is no automatic loading of dsa_loop_bdinfo.ko which
is needed.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/dsa/sja1105/sja1105_vl.c:468:6: warning: variable ‘prev_time’ set but not used [-Wunused-but-set-variable]
u32 prev_time = 0;
^~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Restrict the TTEthernet hardware support on this switch to operate as
closely as possible to IEEE 802.1Qci as possible. This means that it can
perform PTP-time-based ingress admission control on streams identified
by {DMAC, VID, PCP}, which is useful when trying to ensure the
determinism of traffic scheduled via IEEE 802.1Qbv.
The oddity comes from the fact that in hardware (and in TTEthernet at
large), virtual links always need a full-blown action, including not
only the type of policing, but also the list of destination ports. So in
practice, a single tc-gate action will result in all packets getting
dropped. Additional actions (either "trap" or "redirect") need to be
specified in the same filter rule such that the conforming packets are
actually forwarded somewhere.
Apart from the VL Lookup, Policing and Forwarding tables which need to
be programmed for each flow (virtual link), the Schedule engine also
needs to be told to open/close the admission gates for each individual
virtual link. A fairly accurate (and detailed) description of how that
works is already present in sja1105_tas.c, since it is already used to
trigger the egress gates for the tc-taprio offload (IEEE 802.1Qbv). Key
point here, we remember that the schedule engine supports 8
"subschedules" (execution threads that iterate through the global
schedule in parallel, and that no 2 hardware threads must execute a
schedule entry at the same time). For tc-taprio, each egress port used
one of these 8 subschedules, leaving a total of 4 subschedules unused.
In principle we could have allocated 1 subschedule for the tc-gate
offload of each ingress port, but actually the schedules of all virtual
links installed on each ingress port would have needed to be merged
together, before they could have been programmed to hardware. So
simplify our life and just merge the entire tc-gate configuration, for
all virtual links on all ingress ports, into a single subschedule. Be
sure to check that against the usual hardware scheduling conflicts, and
program it to hardware alongside any tc-taprio subschedule that may be
present.
The following scenarios were tested:
1. Quantitative testing:
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate index 1 base-time 0 \
sched-entry OPEN 1200 -1 -1 \
sched-entry CLOSE 1200 -1 -1 \
action trap
ping 192.168.1.2 -f
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
.............................
--- 192.168.1.2 ping statistics ---
948 packets transmitted, 467 received, 50.7384% packet loss, time 9671ms
2. Qualitative testing (with a phase-aligned schedule - the clocks are
synchronized by ptp4l, not shown here):
Receiver (sja1105):
tc qdisc add dev swp2 clsact
now=$(phc_ctl /dev/ptp1 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate base-time ${base_time} \
sched-entry OPEN 60000 -1 -1 \
sched-entry CLOSE 40000 -1 -1 \
action trap
Sender (enetc):
now=$(phc_ctl /dev/ptp0 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc qdisc add dev eno0 parent root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S 01 50000 \
sched-entry S 00 50000 \
flags 2
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
1425 packets transmitted, 1424 packets received, 0% packet loss
round-trip min/avg/max = 0.322/0.361/0.990 ms
And just for comparison, with the tc-taprio schedule deleted:
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
33 packets transmitted, 19 packets received, 42% packet loss
round-trip min/avg/max = 0.336/0.464/0.597 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement tc-flower offloads for redirect, trap and drop using
non-critical virtual links.
Commands which were tested to work are:
# Send frames received on swp2 with a DA of 42:be:24:9b:76:20 to the
# CPU and to swp3. This type of key (DA only) when the port's VLAN
# awareness state is off.
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw dst_mac 42:be:24:9b:76:20 \
action mirred egress redirect dev swp3 \
action trap
# Drop frames received on swp2 with a DA of 42:be:24:9b:76:20, a VID
# of 100 and a PCP of 0.
tc filter add dev swp2 ingress protocol 802.1Q flower skip_sw \
dst_mac 42:be:24:9b:76:20 vlan_id 100 vlan_prio 0 action drop
Under the hood, all rules match on DMAC, VID and PCP, but when VLAN
filtering is disabled, those are set internally by the driver to the
port-based defaults. Because we would be put in an awkward situation if
the user were to change the VLAN filtering state while there are active
rules (packets would no longer match on the specified keys), we simply
deny changing vlan_filtering unless the list of flows offloaded via
virtual links is empty. Then the user can re-add new rules.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual links are a sja1105 hardware concept of executing various flow
actions based on a key extracted from the frame's DMAC, VID and PCP.
Currently the tc-flower offload code supports only parsing the DMAC if
that is the broadcast MAC address, and the VLAN PCP. Extract the key
parsing logic from the L2 policers functionality and move it into its
own function, after adding extra logic for matching on any DMAC and VID.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the register definitions for the:
- VL Lookup Table
- VL Policing Table
- VL Forwarding Table
- VL Forwarding Parameters Table
These are needed in order to perform TTEthernet operations: QoS
classification, flow-based policing and/or frame redirecting with the
switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of sja1105_port_status_ether structure into the
statistics causes the frame size to go over the warning limit:
drivers/net/dsa/sja1105/sja1105_ethtool.c:421:6: error: stack frame size of 1104 bytes in function 'sja1105_get_ethtool_stats' [-Werror,-Wframe-larger-than=]
Use dynamic allocation to avoid this.
Fixes: 336aa67bd0 ("net: dsa: sja1105: show more ethtool statistics counters for P/Q/R/S")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running 'bridge fdb dump' on Felix, sometimes learnt and static MAC
addresses would appear, sometimes they wouldn't.
Turns out, the MAC table has 4096 entries on VSC7514 (Ocelot) and 8192
entries on VSC9959 (Felix), so the existing code from the Ocelot common
library only dumped half of Felix's MAC table. They are both organized
as a 4-way set-associative TCAM, so we just need a single variable
indicating the correct number of rows.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the sja1105 external timestamping input is not as generic
as we thought. When fed a signal with 50% duty cycle, it will timestamp
both the rising and the falling edge. When fed a short pulse signal,
only the timestamp of the falling edge will be seen in the PTPSYNCTS
register, because that of the rising edge had been overwritten. So the
moral is: don't feed it short pulse inputs.
Luckily this is not a complete deal breaker, as we can still work with
1 Hz square waves. But the problem is that the extts polling period was
not dimensioned enough for this input signal. If we leave the period at
half a second, we risk losing timestamps due to jitter in the measuring
process. So we need to increase it to 4 times per second.
Also, the very least we can do to inform the user is to deny any other
flags combination than with PTP_RISING_EDGE and PTP_FALLING_EDGE both
set.
Fixes: 747e5eb31d ("net: dsa: sja1105: configure the PTP_CLK pin as EXT_TS or PER_OUT")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no specific configuration of the felix switch in the device
tree, but only the default configuration (ie. given by the SoCs dtsi
file), the probe fails because no CPU port has been set. On the other
hand you cannot set a default CPU port because that depends on the
actual board using the switch.
[ 2.701300] DSA: tree 0 has no CPU port
[ 2.705167] mscc_felix 0000:00:00.5: Failed to register DSA switch: -22
[ 2.711844] mscc_felix: probe of 0000:00:00.5 failed with error -22
Thus let the device tree disable this device entirely, like it is also
done with the enetc driver of the same SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading and reporting the 10G link status on the
88e6390 in addition to the 1000BASE-X/2500BASE-X/SGMII status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private MV88E6390_PCS_CONTROL_1 definitions in serdes.h reflects
the IEEE 802.3 standard PCS control register 1 definitions, only
offset by 0x1000 in the PHYXS register space. Rather than inventing
our own, use those that already exist, and name the register
MV88E6390_10G_CTRL1.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d1cbfd771c ("ptp_clock: Allow for it to be optional") changed
all PTP-capable Ethernet drivers from `select PTP_1588_CLOCK` to `imply
PTP_1588_CLOCK`, "in order to break the hard dependency between the PTP
clock subsystem and ethernet drivers capable of being clock providers."
As a result it is possible to build PTP-capable Ethernet drivers without
the PTP subsystem by deselecting PTP_1588_CLOCK. Drivers are required to
handle the missing dependency gracefully.
Some PTP-capable Ethernet drivers (e.g., TI_CPSW) factor their PTP code
out into separate drivers (e.g., TI_CPTS_MOD). The above commit also
changed these PTP-specific drivers to `imply PTP_1588_CLOCK`, making it
possible to build them without the PTP subsystem. But as Grygorii
Strashko noted in [1]:
On Wed, Apr 22, 2020 at 02:16:11PM +0300, Grygorii Strashko wrote:
> Another question is that CPTS completely nonfunctional in this case and
> it was never expected that somebody will even try to use/run such
> configuration (except for random build purposes).
In my view, enabling a PTP-specific driver without the PTP subsystem is
a configuration error made possible by the above commit. Kconfig should
not allow users to create a configuration with missing dependencies that
results in "completely nonfunctional" drivers.
I audited all network drivers that call ptp_clock_register() but merely
`imply PTP_1588_CLOCK` and found five PTP-specific drivers that are
likely nonfunctional without PTP_1588_CLOCK:
NET_DSA_MV88E6XXX_PTP
NET_DSA_SJA1105_PTP
MACB_USE_HWSTAMP
CAVIUM_PTP
TI_CPTS_MOD
Note how these symbols all reference PTP or timestamping in their name;
this is a clue that they depend on PTP_1588_CLOCK.
Change them from `imply PTP_1588_CLOCK` [2] to `depends on PTP_1588_CLOCK`.
I'm not using `select PTP_1588_CLOCK` here because PTP_1588_CLOCK has
its own dependencies, which `select` would not transitively apply.
Additionally, remove the `select NET_PTP_CLASSIFY` from CPTS_TI_MOD;
PTP_1588_CLOCK already selects that.
[1]: https://lore.kernel.org/lkml/c04458ed-29ee-1797-3a11-7f3f560553e6@ti.com/
[2]: NET_DSA_SJA1105_PTP had never declared any type of dependency on
PTP_1588_CLOCK (`imply` or otherwise); adding a `depends on PTP_1588_CLOCK`
here seems appropriate.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d1cbfd771c ("ptp_clock: Allow for it to be optional")
Signed-off-by: Clay McClure <clay@daemons.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is not used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARL searches are done by reading two ARL entries at a time, do not cap
the search at 1024 which would only limit us to half of the possible ARL
capacity, but use b53_max_arl_entries() instead which does the right
multiplication between bins and indexes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for doing proper upper bound checking of FDB/MDB entries
being added to the ARL, provide the number of ARL buckets for each
switch chip we support. All chips have 1024 buckets, except 7278 which
has only 256.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable currently holds the number of ARL bins per ARL buckets,
which is different from the number of ARL entries which would be bins
times buckets. We will be adding a num_arl_buckets in a subsequent patch
so get variables straight now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These struct members named 'phylink_validate' was assigned twice:
static const struct mv88e6xxx_ops mv88e6190_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6190x_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390x_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6191_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
static const struct mv88e6xxx_ops mv88e6290_ops = {
......
.phylink_validate = mv88e6390_phylink_validate,
......
.phylink_validate = mv88e6390_phylink_validate,
};
Remove all the first one and leave the second one which are been used in
fact. Be aware that for 'mv88e6190x_ops' the assignment functions is
different while the others are all the same. This fixes the following
coccicheck warning:
drivers/net/dsa/mv88e6xxx/chip.c:3911:48-49: phylink_validate: first
occurrence line 3965, second occurrence line 3967
drivers/net/dsa/mv88e6xxx/chip.c:3970:49-50: phylink_validate: first
occurrence line 4024, second occurrence line 4026
drivers/net/dsa/mv88e6xxx/chip.c:4029:48-49: phylink_validate: first
occurrence line 4082, second occurrence line 4085
drivers/net/dsa/mv88e6xxx/chip.c:4184:48-49: phylink_validate: first
occurrence line 4238, second occurrence line 4242
Fixes: 4262c38dc4 ("net: dsa: mv88e6xxx: Add SERDES stats counters to all 6390 family members")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it can be seen that the VSC9959 (Felix) switch will not flood
frames if they have a VLAN tag with a PCP of 1-7 (nonzero).
It turns out that Felix is quite different from its cousin, Ocelot, in
that frame flooding can be allowed/denied per traffic class. Where
Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8.
The approach that this driver is going to take is "thanks, but no
thanks". We have no use case of limiting the flooding domain based on
traffic class, so we just want to allow packets to be flooded, no matter
what traffic class they have.
So we copy the line of code from ocelot.c which does the one-shot
initialization of the flooding PGIDs, and we add it to felix.c as well -
except replicated 8 times.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards do not have the RX_ER MII signal connected. Normally in such
situation, those pins would be grounded, but then again, some boards
left it electrically floating.
When sending traffic to those switch ports, one can see that the
N_SOFERR statistics counter is incrementing once per each packet. The
user manual states for this counter that it may count the number of
frames "that have the MII error input being asserted prior to or
up to the SOF delimiter byte". So the switch MAC is sampling an
electrically floating signal, and preventing proper traffic reception
because of that.
As a workaround, enable the internal weak pull-downs on the input pads
for the MII control signals. This way, a floating signal would be
internally tied to ground.
The logic levels of signals which _are_ externally driven should not be
bothered by this 40-50 KOhm internal resistor. So it is not an issue to
enable the internal pull-down unconditionally, irrespective of PHY
interface type (MII, RMII, RGMII, SGMII) and of board layout.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of platform_get_irq_byname_optional() to avoid printing
messages on the kernel console that interrupts cannot be found.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In VLAN-unaware mode, the Egress Tag (EG_TAG) field in Port VLAN
Control register must be set to Consistent to let tagged frames pass
through as is, otherwise their tags will be stripped.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To rehash a previous explanation given in commit 1c44ce560b ("net:
mscc: ocelot: fix vlan_filtering when enslaving to bridge before link is
up"), the switch driver operates the in a mode where a single VLAN can
be transmitted as untagged on a particular egress port. That is the
"native VLAN on trunk port" use case.
The configuration for this native VLAN is driven in 2 ways:
- Set the egress port rewriter to strip the VLAN tag for the native
VID (as it is egress-untagged, after all).
- Configure the ingress port to drop untagged and priority-tagged
traffic, if there is no native VLAN. The intention of this setting is
that a trunk port with no native VLAN should not accept untagged
traffic.
Since both of the above configurations for the native VLAN should only
be done if VLAN awareness is requested, they are actually done from the
ocelot_port_vlan_filtering function, after the basic procedure of
toggling the VLAN awareness flag of the port.
But there's a problem with that simplistic approach: we are trying to
juggle with 2 independent variables from a single function:
- Native VLAN of the port - its value is held in port->vid.
- VLAN awareness state of the port - currently there are some issues
here, more on that later*.
The actual problem can be seen when enslaving the switch ports to a VLAN
filtering bridge:
0. The driver configures a pvid of zero for each port, when in
standalone mode. While the bridge configures a default_pvid of 1 for
each port that gets added as a slave to it.
1. The bridge calls ocelot_port_vlan_filtering with vlan_aware=true.
The VLAN-filtering-dependent portion of the native VLAN
configuration is done, considering that the native VLAN is 0.
2. The bridge calls ocelot_vlan_add with vid=1, pvid=true,
untagged=true. The native VLAN changes to 1 (change which gets
propagated to hardware).
3. ??? - nobody calls ocelot_port_vlan_filtering again, to reapply the
VLAN-filtering-dependent portion of the native VLAN configuration,
for the new native VLAN of 1. One can notice that after toggling "ip
link set dev br0 type bridge vlan_filtering 0 && ip link set dev br0
type bridge vlan_filtering 1", the new native VLAN finally makes it
through and untagged traffic finally starts flowing again. But
obviously that shouldn't be needed.
So it is clear that 2 independent variables need to both re-trigger the
native VLAN configuration. So we introduce the second variable as
ocelot_port->vlan_aware.
*Actually both the DSA Felix driver and the Ocelot driver already had
each its own variable:
- Ocelot: ocelot_port_private->vlan_aware
- Felix: dsa_port->vlan_filtering
but the common Ocelot library needs to work with a single, common,
variable, so there is some refactoring done to move the vlan_aware
property from the private structure into the common ocelot_port
structure.
Fixes: 97bb69e1e3 ("net: mscc: ocelot: break apart ocelot_vlan_port_apply")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Rix