Usually, there is no palm rejection for touchscreens. You don't rest
your palm on the touchscreen while interacting with it.
However, some wacom devices do so because you can rest your palm while
interacting with the stylus.
Unfortunately, the spec for touchscreens[1] is less precise than the one
for touchpads[2]. This leads to a situation where it's 'legitimate'
for a touchscreen to provide both tipswitch off and confidence off in the
same report.
Work around that by keeping the slot active for one frame where we report
MT_TOOL_PALM, and then synthesizing the release event in a separate frame.
frame
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[rebased and new commit message]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to Microsoft specification [1] for Precision Touchpads (and
Touchscreens) the devices use "confidence" reports to signal accidental
touches, or contacts that are "too large to be a finger". Instead of
simply marking contact inactive in this case (which causes issues if
contact was originally proper and we lost confidence in it later, as
this results in accidental clicks, drags, etc), let's report such
contacts as MT_TOOL_PALM and let userspace decide what to do.
[1] https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[splitted and rebased]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dell Canvas 27 has a tool that can be put on the surface and acts
as a dial. The firmware processes the detection of the tool and forward
regular HID reports with X, Y, Azimuth, rotation, width/height.
The firmware also exports Contact ID, Countact Count which may hint that
several totems can be used at the same time (the FW only supports one).
We can tell that MT_TOOL_DIAL will be reported by setting the min/max
of ABS_MT_TOOL_TYPE to MT_TOOL_DIAL.
This tool is aimed at being used by the system and not the applications,
so the user space processing should not go through the regular touch
inputs.
We set INPUT_PROP_DIRECT which applies ID_INPUT_TOUCHSCREEN to this new
type of devices, but we will counter this for the time being with the
special udev hwdb entry mentioned above.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1511846
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current way of handling multitouch data is not very straightforward:
- in mt_event() we do nothing
- in mt_report() we:
- do some gym to fetch the scantime and the contact count
- then iterate over the input fields where we copy the data to a
temporary place
- when we see the last field in a slot, we then use this data to emit
the input data
A more streamlined way is to first get all of the address in the report
of all fields, and then just pick the fields we are interested in in
mt_report()
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that the driver can handle more than one multitouch collection in
a single HID device, ditch the last bit that contains us to use only
one mt collection.
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a device has more than one multitouch collection, there is a chance
we need per tool quirks. This is the case for the Totem on the Dell
Canvas.
Note that thesysfs attribute quirks can now get out of sync, but there
should not be much users of it as it's debugging only.
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, hid-multitouch can only handle one multitouch collection at
a time. This is an issue for the Dell Canvas, as the Totem (a dial tool)
is also using a multitouch-like collection.
Factor out the multitouch collection data in their own struct.
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
const is a magic keyword here :)
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to [1] and also seemingly agreed by [2], the Scan Time usage
(0x0D 0x56) is a report level usage, not a contact level usage.
However, the hid-multitouch driver currently includes HID_DG_SCANTIME
when calculating `td->last_slot_field', which may lead to
mt_complete_slot() being prematurely called in certain cases (e.g. when
each touch input report includes more than one contact and the Scan Time
usage appears before any contact logical collection).
This patch fixes the issue by skipping mt_store_field() on
HID_DG_SCANTIME, similar to how HID_DG_CONTACTCOUNT and
HID_DG_CONTACTMAX are handled.
[1] https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/windows-precision-touchpad-required-hid-top-level-collections#windows-precision-touchpad-input-reports
[2] https://patchwork.kernel.org/patch/1742181/
Fixes: 29cc309d8b ("HID: hid-multitouch: forward MSC_TIMESTAMP")
Signed-off-by: Ben Chan <benchan@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some exit paths from mt_need_to_apply_feature() returned int instead
of bool; fix that up.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Win8 spec also declare other features we want to support:
latency and surface and button switches.
Though it doesn't seem we need to activate those by default, we have been
proved in the past that manufacturers rely on the Windows driver behavior
so we better mimic it to prevent further issues.
The current way of setting the features is cumbersome. It avoids iterating
over the list of features, but the way we store/retrieve the data just
doesn't scale with more than two values.
So iterate over the features when we decide to switch on the device and
make it simpler to extend.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We now have HID_QUIRK_INPUT_PER_APPLICATION that splits the devices
into several devices. This helps us as we can now rely on hid-input
to set the names for us.
Also, this helps removing some magical numbers '0' when calling
.input_configured().
The only thing to take care of is that the field .report in struct
hid_input is now null. We need to iterate over the full list of
reports attached to a hid_input.
This is required for some Advanced Silicon touchscreen to correctly apply
the HID_QUIRK_INPUT_PER_APPLICATION as they have 2 reports associated
with the hidinput node. One contains the Input data, the other one
contains the Output data.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Given that now the quirk handling is done in hid-quirk.c, we can actually
reset the quirks before calling .probe(), so that the drivers do not need
to keep track of initial quirks.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is set by default now, so there is no point setting it in the driver
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no real point of registering an empty input node.
This should be default, but given some drivers need the blank input
node to set it up during input_configured, we need to postpone
the check for hidinput_has_been_populated().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Razer Blade Stealth detects palms too aggressively and this creates
a dead zone around the touchpad. Users like being able to use their
entire touchpad, so we should probably not filter out the "palm" events
from the device and report them as regular touches, leaving the palm
detection up to the upper stack
Link: https://bugs.freedesktop.org/show_bug.cgi?id=105409
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of using the class name, we better have a specific quirk for it
so other classes can make use of it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Follow the change of return type u32 of hid_report_len,
fix all the types of variables those get the return value of
hid_report_len to u32, and all other code already uses u32.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current hid-multitouch driver only allow the report of two
orientations, vertical and horizontal. We use the Azimuth orientation
usage 0x3F under the Digitizer usage page to report orientation if the
device supports it.
Changelog:
v1 -> v2:
- Fix commit message.
- Remove resolution reporting for ABS_MT_ORIENTATION.
v2 -> v3:
- Fix commit message.
v3 -> v4:
- Fix ABS_MT_ORIENTATION ABS param range.
- Don't set ABS_MT_ORIENTATION in ABS_DG_HEIGHT when it is already
set by ABS_DG_AZIMUTH.
v4 -> v5:
- Improve multi-touch-protocol.rst documentation.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to the Win8 Precision Touchpad spec, inside the HID_UP_BUTTON
usage-page usage 1 is for a clickpad getting clicked, 2 for an external
left button and 3 for an external right button. Since Linux uses
BTN_LEFT for a clickpad being clicked we end up mapping both usage 1
and 2 to BTN_LEFT and if a single report contains both then we ended
up always reporting the value of both in a single SYN, e.g. :
BTN_LEFT 1, BTN_LEFT 0, SYN. This happens for example with Hantick
HTT5288 i2c mt touchpads.
This commit fixes this by not immediately reporting left button when we
parse the report, but instead storing or-ing together the values and
reporting the result from mt_sync_frame() when we've a complete frame.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices in "single finger hybrid mode" will send one report per finger,
on some devices only the first report of such a multi-packet frame will
contain a value for BTN_LEFT, in subsequent reports (if multiple fingers
are down) the value is always 0, causing hid-mt to report BTN_LEFT going
1 - 0 - 1 - 0 when pressing a clickpad and putting down a second finger.
This happens for example on USB 0603:0002 mt touchpads.
This commit fixes this by only reporting non touch fields for the first
packet of a (possibly) multi-packet frame.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Windows Precision Touchpad spec "Figure 4 Button Only Down and Up"
and "Table 9 Report Sequence for Button Only Down and Up" indicate
that the first packet of a (possibly hybrid mode multi-packet) frame
may contain a contact-count of 0 if only a button is pressed and no
fingers are detected.
This means that a value of 0 for contact-count is a valid value and
should be used as expected contact count when it is the first packet
(num_received == 0), as extra check to make sure that this is the first
packet of a buttons only frame, we also check that the timestamp is
different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix alphabetic sorting of mt_devices hid_device_id table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
(introduced by 686fef928b ("timer: Prepare to change timer callback
argument type")) to pass the timer pointer explicitly. Adds pointer back to
hid_device for multitouch.
[jkosina@suse.cz: extend changelog a little bit as asked for by Benjamin]
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Computes and forwards the device timestamp according to the specification.
Many devices use a 16-bit timestamp field, with a resolution of 100us,
therefore rolling around very frequently (every 6.5 seconds). To make sure
there is no ambiguity, the timestamp reported to the input stack reset to
0 whenever the time between 2 received events is greater than
MAX_TIMESTAMP_INTERVAL (1 second).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit fcaa4a07d2.
As noted by Masaki [1], 0x120A + trackpoint will not be used in mass
production machines, so remove the ID accordingly.
[1] http://www.spinics.net/lists/linux-input/msg53222.html
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds ALPS PTP sticks with pid/device id 0x120A to the list of
devices supported by hid-multitouch.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On the 2nd generation Lenovo Tablet only clickpad is working; the
trackpoint and three mouse buttons do not work.
hid_multitouch must export all inputs in order to get trackpoint and
buttons to function.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some laptops have system-control buttons (e.g. KEY_SLEEP) on the same
interface as a hid-multitouch touch-pad.
This commit fixes these buttons not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- support for media keys on Asus T304UA from João Paulo Rechi Vita
- support for Microsoft Win8 Wireless Radio Controls extensions
from João Paulo Rechi Vita
Conflicts:
drivers/hid/hid-ids.h
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
0xff310076 application has been defined by 957b8dffa4 ("HID: multitouch:
Support Asus T304UA media keys") as a vendor-specific application with
symbolic constant HID_VD_ASUS_CUSTOM_MEDIA_KEYS, so let's make use of
it.
Fixes: 957b8dffa4 ("HID: multitouch: Support Asus T304UA media keys")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Asus T304UA convertible sports a magnetic detachable keyboard with
touchpad, which is connected over USB. Most of the keyboard hotkeys are
exposed through the same USB interface as the touchpad, defined in the
report descriptor as follows:
0x06, 0x31, 0xFF, // Usage Page (Vendor Defined 0xFF31)
0x09, 0x76, // Usage (0x76)
0xA1, 0x01, // Collection (Application)
0x05, 0xFF, // Usage Page (Reserved 0xFF)
0x85, 0x5A, // Report ID (90)
0x19, 0x00, // Usage Minimum (0x00)
0x2A, 0xFF, 0x00, // Usage Maximum (0xFF)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x0F, // Report Count (15)
0xB1, 0x02, // Feature (Data,Var,Abs,No Wrap,Linear,Preferred State,No Null Position,Non-volatile)
0x05, 0xFF, // Usage Page (Reserved 0xFF)
0x85, 0x5A, // Report ID (90)
0x19, 0x00, // Usage Minimum (0x00)
0x2A, 0xFF, 0x00, // Usage Maximum (0xFF)
0x15, 0x00, // Logical Minimum (0)
0x26, 0xFF, 0x00, // Logical Maximum (255)
0x75, 0x08, // Report Size (8)
0x95, 0x02, // Report Count (2)
0x81, 0x02, // Input (Data,Var,Abs,No Wrap,Linear,Preferred State,No Null Position)
0xC0, // End Collection
This UsagePage is declared as a variable, but we need to treat it as an
array to be able to map each Usage we care about to its corresponding
input key.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some keyboard + touchpad devices have the Microsoft Win8 Wireless Radio
Controls extensions Usage Page define in the touchpad report descriptor,
so we need to support them in this driver.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that input core insists on having dev->absinfo when device claims to
generate EV_ABS in its dev->evbit, we should not be blindly setting that
bit.
The code in question might have been needed before input_set_abs_params()
started setting EV_ABS in device's evbit, but not anymore, and is now
breaking devices such as SMART SPNL-6075 Touchscreen.
Fixes: 6ecfe51b40 ("Input: refuse to register absolute devices ...")
Reported-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Tested-by: Matthias Fend <Matthias.Fend@wolfvision.net>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of unconditionally expiring the timer and calling a long
mt_release_contacts(), we can check if some slots are used when the
timer expires.
We can also remove the timer if we happen to receive all the releases.
The logic behind the MT_IO_FLAGS_PENDING_SLOTS could be implemented by
counting how many slots are active, but using bits feels slightly more
efficient.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of blindly trusting the hardware to send us release, we should
consider some events can get lost and release them when we judge time has
come.
The Windows 8 spec allows to be confident in the fact that the device
will continuously report events when a finger touches the surface.
This has been tested on the HID recording database I have, and all of
those devices behave properly.
Also, Arek tested it on his Lenovo Yoga 910, which exports such bug in
some situations, when the movements are rather slow.
We use an atomic bit here to guard against concurrent accesses to the mt
slots because both mt_process_mt_event() and mt_expired_timeout() are
called in interrupt context.
Signed-off-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
(1 << X) is wrong. We should use BIT(X)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Arek Burdach <arek.burdach@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Google Rose Touchpad USB PID and required quirks.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Support PTP Stick and Touchpad device. This Touchpad is Precision Touchpad
(PTP), and Stick Pointer data is the same as Mouse; Stick Pointer works as
Mouse.
[jkosina@suse.cz: changelog deuglification]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Quoting from Jonathan Clarke in previous thread(2017/01/24):
"This division by 2 was added along with the touch width/height fields 6 years
ago so that those fields 'match the visual scale of the touch' for a specific
device (3M PCT)" "The scaling is also discarding information about touch size
(1 bit for each of width/height) which is useful for any application that wants
to know about it."
Jonathan mentioned just what I thought in a new project recently. It dosen't
make sense to discard 1 bit width/height in general case according to the spec
in multi-touch-protocol.txt so I would like to make a slight change here.
A quirk MT_QUIRK_TOUCH_SIZE_SCALING was added to service devices like 3M PCT
with a special visual scale and the division by 2 only take effect with devices
like that.
[jkosina@suse.cz: reformat changelog]
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The LG Melfas touchscreen has a bad firmware where it declares the Contact ID
field as constant while it shouldn't. This messes up the autodetection and the
reporting of the events by hid-multitouch given that hid-input ignores constant
fields.
The autodetection is simply worked around by manually adding the device to
hid_have_special_driver[].
The processing of the events requires either a report fixup, or some specific
case handling. Given that the report fixup would require to basically rewrite
all the report descriptor, I went for the programatic way of fixing that after
the report descriptors are loaded.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1416181
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Dmitry Torokhov