Allow an L3 master device to act as the loopback for that L3 domain.
For IPv4 the device can also have the address 127.0.0.1.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.
To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)
This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.
This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow udp and raw sockets to send by oif that is an enslaved interface
versus the l3mdev/VRF device. For example, this allows BFD to use ifindex
from IP_PKTINFO on a receive to send a response without the need to
convert to the VRF index. It also allows ping and ping6 to work when
specifying an enslaved interface (e.g., ping -I swp1 <ip>) which is
a natural use case.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP_INC_STATS_BH() to __IP_INC_STATS(), to
better express this is used in non preemptible context.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For local routes that require a particular output interface we do not want
to cache the result. Caching the result causes incorrect behaviour when
there are multiple source addresses on the interface. The end result
being that if the intended recipient is waiting on that interface for the
packet he won't receive it because it will be delivered on the loopback
interface and the IP_PKTINFO ipi_ifindex will be set to the loopback
interface as well.
This can be tested by running a program such as "dhcp_release" which
attempts to inject a packet on a particular interface so that it is
received by another program on the same board. The receiving process
should see an IP_PKTINFO ipi_ifndex value of the source interface
(e.g., eth1) instead of the loopback interface (e.g., lo). The packet
will still appear on the loopback interface in tcpdump but the important
aspect is that the CMSG info is correct.
Sample dhcp_release command line:
dhcp_release eth1 192.168.204.222 02:11:33:22:44:66
Signed-off-by: Allain Legacy <allain.legacy@windriver.com>
Signed off-by: Chris Friesen <chris.friesen@windriver.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivek reported a kernel exception deleting a VRF with an active
connection through it. The root cause is that the socket has a cached
reference to a dst that is destroyed. Converting the dst_destroy to
dst_release and letting proper reference counting kick in does not
work as the dst has a reference to the device which needs to be released
as well.
I talked to Hannes about this at netdev and he pointed out the ipv4 and
ipv6 dst handling has dst_ifdown for just this scenario. Rather than
continuing with the reinvented dst wheel in VRF just remove it and
leverage the ipv4 and ipv6 versions.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.
Fix this issue by checking and removing route cache when we get route.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit deaa0a6a93 ("net: Lookup actual route when oif is VRF device")
exposed a bug in __ip_route_output_key_hash for VRF devices: on FIB lookup
failure if the oif is specified the current logic drops to make_route on
the assumption that the route tables are wrong. For VRF/L3 master devices
this leads to wrong dst entries and route lookups. For example:
$ ip route ls table vrf-red
unreachable default
broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2
10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2
local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2
broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2
$ ip route get oif vrf-red 1.1.1.1
1.1.1.1 dev vrf-red src 10.0.0.2
cache
With this patch:
$ ip route get oif vrf-red 1.1.1.1
RTNETLINK answers: No route to host
which is the correct response based on the default route
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network namespace is already passed into dst_output pass it into
dst->output lwt->output and friends.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with the other similar methods in the kernel pass a
struct sock into the dst_ops .local_out method.
Simplifying the socket passing case is needed a prequel to passing a
struct net reference into .local_out.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user specifies a VRF device in a get route query the custom route
pointing to the VRF device is returned:
$ ip route ls table vrf-red
unreachable default
broadcast 10.2.1.0 dev eth1 proto kernel scope link src 10.2.1.2
10.2.1.0/24 dev eth1 proto kernel scope link src 10.2.1.2
local 10.2.1.2 dev eth1 proto kernel scope host src 10.2.1.2
broadcast 10.2.1.255 dev eth1 proto kernel scope link src 10.2.1.2
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev vrf-red
cache
Add the flags to skip the custom route and go directly to the FIB. With
this patch the actual route is returned:
$ ip route get oif vrf-red 10.2.1.40
10.2.1.40 dev eth1 src 10.2.1.2
cache
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VRF device needs the same path selection following lookup to set source
address. Rather than duplicating code, move existing code into a
function that is exported to modules.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP packets are inspected to let them route together with the flow they
belong to, minimizing the chance that a problematic path will affect flows
on other paths, and so that anycast environments can work with ECMP.
Signed-off-by: Peter Nørlund <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaces the per-packet multipath with a hash-based multipath using
source and destination address.
Signed-off-by: Peter Nørlund <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib_table_lookup tracepoint found 2 places where the flowi4_flags is
not initialized.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to vrf_dev_get_rth with l3mdev_get_rtable.
The check on the flow flags is handled in the l3mdev operation.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to vrf_master_ifindex_rcu and vrf_master_ifindex with either
l3mdev_master_ifindex_rcu or l3mdev_master_ifindex.
The pattern:
oif = vrf_master_ifindex(dev) ? : dev->ifindex;
is replaced with
oif = l3mdev_fib_oif(dev);
And remove the now unused vrf macros.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IFF_VRF_MASTER to IFF_L3MDEV_MASTER and update the name of the
netif_is_vrf and netif_index_is_vrf macros.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
err is initialized to -EINVAL when it is declared. It is not reset until
fib_lookup which is well after the 3 users of the martian_source jump. So
resetting err to -EINVAL at martian_source label is not needed.
Removing that line obviates the need for the martian_source_keep_err label
so delete it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just swaps the ordering of one of the conditional tests in
ip_route_input_mc. Specifically it swaps the testing for the source
address to see if it is loopback, and the test to see if we allow a
loopback source address.
The reason for swapping these two tests is because it is much faster to
test if an address is loopback than it is to dereference several pointers
to get at the net structure to see if the use of loopback is allowed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Very soon, TCP stack might call inet_csk_route_req(), which
calls inet_csk_route_req() with an unlocked listener socket,
so we need to make sure ip_route_output_flow() is not trying to
change any field from its socket argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Man page of ip-route(8) says following about route types:
unreachable - these destinations are unreachable. Packets are dis‐
carded and the ICMP message host unreachable is generated. The local
senders get an EHOSTUNREACH error.
blackhole - these destinations are unreachable. Packets are dis‐
carded silently. The local senders get an EINVAL error.
prohibit - these destinations are unreachable. Packets are discarded
and the ICMP message communication administratively prohibited is
generated. The local senders get an EACCES error.
In the inet6 address family, this was correct, except the local senders
got ENETUNREACH error instead of EHOSTUNREACH in case of unreachable route.
In the inet address family, all three route types generated ICMP message
net unreachable, and the local senders got ENETUNREACH error.
In both address families all three route types now behave consistently
with documentation.
Signed-off-by: Nikola Forró <nforro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_fill_info which is called for 'route get' requests hardcodes the
table id as RT_TABLE_MAIN which is not correct when multiple tables
are used. Use the newly added table id in the rtable to send back
the correct table similar to what is done for IPv6.
To maintain current ABI a new request flag, RTM_F_LOOKUP_TABLE, is
added to indicate the actual table is wanted versus the hardcoded
response.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the FIB table id to rtable to make the information available for
IPv4 as it is for IPv6.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers to rt_dst_alloc have nearly the same initialization following
a successful allocation. Consolidate it into rt_dst_alloc.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the lwtunnel state resides in per-protocol data. This is
a problem if we encapsulate ipv6 traffic in an ipv4 tunnel (or vice versa).
The xmit function of the tunnel does not know whether the packet has been
routed to it by ipv4 or ipv6, yet it needs the lwtstate data. Moving the
lwtstate data to dst_entry makes such inter-protocol tunneling possible.
As a bonus, this brings a nice diffstat.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the capability to redirect dst input in the same way
that dst output is redirected by LWT.
Also, save the original dst.input and and dst.out when setting up
lwtunnel redirection. These can be called by the client as a pass-
through.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with ingress use the index of VRF master device for route lookups on
egress. However, the oif should only be used to direct the lookups to a
specific table. Routes in the table are not based on the VRF device but
rather interfaces that are part of the VRF so do not consider the oif for
lookups within the table. The FLOWI_FLAG_VRFSRC is used to control this
latter part.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ingress use index of VRF master device for route lookups if real device
is enslaved. Rules are expected to be installed for the VRF device to
direct lookups to a specific table.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lwtunnel encap is applied for forwarded packets, but not for
locally-generated packets. This is because the output function is not
overridden in __mkroute_output, unlike it is in __mkroute_input.
The lwtunnel state is correctly set on the rth through the call to
rt_set_nexthop, so all that needs to be done is to override the dst
output function to be lwtunnel_output if there is lwtunnel state
present and it requires output redirection.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
It saves some lines and simplify a bit the code when the state is returning
by this function. It's also useful to handle a NULL entry.
To avoid too long lines, I've also renamed lwtunnel_state_get() and
lwtunnel_state_put() to lwtstate_get() and lwtstate_put().
CC: Thomas Graf <tgraf@suug.ch>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_default considers alternative routes only when
res->fi is for the first alias in res->fa_head. In the
common case this can happen only when the initial lookup
matches the first alias with highest TOS value. This
prevents the alternative routes to require specific TOS.
This patch solves the problem as follows:
- routes that require specific TOS should be returned by
fib_select_default only when TOS matches, as already done
in fib_table_lookup. This rule implies that depending on the
TOS we can have many different lists of alternative gateways
and we have to keep the last used gateway (fa_default) in first
alias for the TOS instead of using single tb_default value.
- as the aliases are ordered by many keys (TOS desc,
fib_priority asc), we restrict the possible results to
routes with matching TOS and lowest metric (fib_priority)
and routes that match any TOS, again with lowest metric.
For example, packet with TOS 8 can not use gw3 (not lowest
metric), gw4 (different TOS) and gw6 (not lowest metric),
all other gateways can be used:
tos 8 via gw1 metric 2 <--- res->fa_head and res->fi
tos 8 via gw2 metric 2
tos 8 via gw3 metric 3
tos 4 via gw4
tos 0 via gw5
tos 0 via gw6 metric 1
Reported-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new IP tunnel lightweight tunnel type which allows
to specify IP tunnel instructions per route. Only IPv4 is supported
at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new flowi_tunnel structure which is a subset of ip_tunnel_key to
allow routes to match on tunnel metadata. For now, the tunnel id is
added to flowi_tunnel which allows for routes to be bound to specific
virtual tunnels.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces a new dst_metadata which enables to carry per packet metadata
between forwarding and processing elements via the skb->dst pointer.
The structure is set up to be a union. Thus, each separate type of
metadata requires its own dst instance. If demand arises to carry
multiple types of metadata concurrently, metadata dst entries can be
made stackable.
The metadata dst entry is refcnt'ed as expected for now but a non
reference counted use is possible if the reference is forced before
queueing the skb.
In order to allow allocating dsts with variable length, the existing
dst_alloc() is split into a dst_alloc() and dst_init() function. The
existing dst_init() function to initialize the subsystem is being
renamed to dst_subsys_init() to make it clear what is what.
The check before ip_route_input() is changed to ignore metadata dsts
and drop the dst inside the routing function thus allowing to interpret
metadata in a later commit.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For input routes with tunnel encap state this patch redirects
dst output functions to lwtunnel_output which later resolves to
the corresponding lwtunnel output function.
This has been tested to work with mpls ip tunnels.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support in ipv4 fib functions to parse user
provided encap attributes and attach encap state data to fib_nh
and rtable.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags local variable in __mkroute_input is not used as a variable.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is only enabled with the new per-interface or ipv4 global
sysctls called 'ignore_routes_with_linkdown'.
net.ipv4.conf.all.ignore_routes_with_linkdown = 0
net.ipv4.conf.default.ignore_routes_with_linkdown = 0
net.ipv4.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, will report to userspace that a route is
dead and will no longer resolve to this nexthop when performing a fib
lookup. This will signal to userspace that the route will not be
selected. The signalling of a RTNH_F_DEAD is only passed to userspace
if the sysctl is enabled and link is down. This was done as without it
the netlink listeners would have no idea whether or not a nexthop would
be selected. The kernel only sets RTNH_F_DEAD internally if the
interface has IFF_UP cleared.
With the new sysctl set, the following behavior can be observed
(interface p8p1 is link-down):
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 dead linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 dead linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
90.0.0.1 via 70.0.0.2 dev p7p1 src 70.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 via 10.0.5.2 dev p9p1 src 10.0.5.15
cache
While the route does remain in the table (so it can be modified if
needed rather than being wiped away as it would be if IFF_UP was
cleared), the proper next-hop is chosen automatically when the link is
down. Now interface p8p1 is linked-up:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
192.168.56.0/24 dev p2p1 proto kernel scope link src 192.168.56.2
90.0.0.1 via 80.0.0.2 dev p8p1 src 80.0.0.1
cache
local 80.0.0.1 dev lo src 80.0.0.1
cache <local>
80.0.0.2 dev p8p1 src 80.0.0.1
cache
and the output changes to what one would expect.
If the sysctl is not set, the following output would be expected when
p8p1 is down:
default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1 proto kernel scope link src 10.0.5.15
70.0.0.0/24 dev p7p1 proto kernel scope link src 70.0.0.1
80.0.0.0/24 dev p8p1 proto kernel scope link src 80.0.0.1 linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1 metric 1 linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1 metric 2
Since the dead flag does not appear, there should be no expectation that
the kernel would skip using this route due to link being down.
v2: Split kernel changes into 2 patches, this actually makes a
behavioral change if the sysctl is set. Also took suggestion from Alex
to simplify code by only checking sysctl during fib lookup and
suggestion from Scott to add a per-interface sysctl.
v3: Code clean-ups to make it more readable and efficient as well as a
reverse path check fix.
v4: Drop binary sysctl
v5: Whitespace fixups from Dave
v6: Style changes from Dave and checkpatch suggestions
v7: One more checkpatch fixup
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da41301 ("ipv4: Cache ip_error() routes even when not forwarding.")
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In setups with a global scope address on an interface, and a lesser
scope address on an interface sending IGMP reports, the reports can be
sent using the other interfaces global scope address rather than the
local interface address. RFC 2236 suggests:
Ignore the Report if you cannot identify the source address of
the packet as belonging to a subnet assigned to the interface on
which the packet was received.
since such reports could be forged.
Look at the protocol when deciding if a RT_SCOPE_LINK address should
be used for the packet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under stress, ip_idents_reserve() is accessing a contended
cache line twice, with non optimal MESI transactions.
If we place timestamps in separate location, we reduce this
pressure by ~50% and allow atomic_add_return() to issue
a Request for Ownership.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3cdaa5be9e ("ipv4: Don't
increase PMTU with Datagram Too Big message") broke PMTU in cases
where the rt_pmtu value has expired but is smaller than the new
PMTU value.
This obsolete rt_pmtu then prevents the new PMTU value from being
installed.
Fixes: 3cdaa5be9e ("ipv4: Don't increase PMTU with Datagram Too Big message")
Reported-by: Gerd v. Egidy <gerd.von.egidy@intra2net.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for non-NULL pointer is done as x != NULL and sometimes as x. x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As namespaces are sometimes used with overlapping ip address ranges,
we should also use the namespace as input to the hash to select the ip
fragmentation counter bucket.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After my change to neigh_hh_init to obtain the protocol from the
neigh_table there are no more users of protocol in struct dst_ops.
Remove the protocol field from dst_ops and all of it's initializers.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 1191 said, "a host MUST not increase its estimate of the Path
MTU in response to the contents of a Datagram Too Big message."
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not caching dst_entries which cause redirects could be exploited by hosts
on the same subnet, causing a severe DoS attack. This effect aggravated
since commit f886497212 ("ipv4: fix dst race in sk_dst_get()").
Lookups causing redirects will be allocated with DST_NOCACHE set which
will force dst_release to free them via RCU. Unfortunately waiting for
RCU grace period just takes too long, we can end up with >1M dst_entries
waiting to be released and the system will run OOM. rcuos threads cannot
catch up under high softirq load.
Attaching the flag to emit a redirect later on to the specific skb allows
us to cache those dst_entries thus reducing the pressure on allocation
and deallocation.
This issue was discovered by Marcelo Leitner.
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 053c095a82 ("netlink: make nlmsg_end() and genlmsg_end()
void") didn't catch all of the cases where callers were breaking out
on the return value being equal to zero, which they no longer should
when zero means success.
Fix all such cases.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RAW sockets with hdrinc suffer from contention on rt_uncached_lock
spinlock.
One solution is to use percpu lists, since most routes are destroyed
by the cpu that created them.
It is unclear why we even have to put these routes in uncached_list,
as all outgoing packets should be freed when a device is dismantled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: caacf05e5a ("ipv4: Properly purge netdev references on uncached routes.")
Signed-off-by: David S. Miller <davem@davemloft.net>
If we cache them, the kernel will reuse them, independently of
whether forwarding is enabled or not. Which means that if forwarding is
disabled on the input interface where the first routing request comes
from, then that unreachable result will be cached and reused for
other interfaces, even if forwarding is enabled on them. The opposite
is also true.
This can be verified with two interfaces A and B and an output interface
C, where B has forwarding enabled, but not A and trying
ip route get $dst iif A from $src && ip route get $dst iif B from $src
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit f187bc6efb ("ipv4: No need to set generic neighbour pointer")
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we genarate a blackhole route route whenever we have
matching policies but can not resolve the states. Here we assume
that dst_output() is called to kill the balckholed packets.
Unfortunately this assumption is not true in all cases, so
it is possible that these packets leave the system unwanted.
We fix this by generating blackhole routes only from the
route lookup functions, here we can guarantee a call to
dst_output() afterwards.
Fixes: 2774c131b1 ("xfrm: Handle blackhole route creation via afinfo.")
Reported-by: Konstantinos Kolelis <k.kolelis@sirrix.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Lets make this hash function a bit secure, as ICMP attacks are still
in the wild.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nh_exceptions is effectively used under rcu, but lacks proper
barriers. Between kzalloc() and setting of nh->nh_exceptions(),
we need a proper memory barrier.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace uses of get_cpu_var for address calculation through this_cpu_ptr.
Cc: netdev@vger.kernel.org
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since fib_lookup cannot return ESRCH no longer,
checking for this error code is no longer neccesary.
Signed-off-by: Niv Yehezkel <executerx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "Counting Packets Sent Between Arbitrary Internet Hosts", Jeffrey and
Jedidiah describe ways exploiting linux IP identifier generation to
infer whether two machines are exchanging packets.
With commit 73f156a6e8 ("inetpeer: get rid of ip_id_count"), we
changed IP id generation, but this does not really prevent this
side-channel technique.
This patch adds a random amount of perturbation so that IP identifiers
for a given destination [1] are no longer monotonically increasing after
an idle period.
Note that prandom_u32_max(1) returns 0, so if generator is used at most
once per jiffy, this patch inserts no hole in the ID suite and do not
increase collision probability.
This is jiffies based, so in the worst case (HZ=1000), the id can
rollover after ~65 seconds of idle time, which should be fine.
We also change the hash used in __ip_select_ident() to not only hash
on daddr, but also saddr and protocol, so that ICMP probes can not be
used to infer information for other protocols.
For IPv6, adds saddr into the hash as well, but not nexthdr.
If I ping the patched target, we can see ID are now hard to predict.
21:57:11.008086 IP (...)
A > target: ICMP echo request, seq 1, length 64
21:57:11.010752 IP (... id 2081 ...)
target > A: ICMP echo reply, seq 1, length 64
21:57:12.013133 IP (...)
A > target: ICMP echo request, seq 2, length 64
21:57:12.015737 IP (... id 3039 ...)
target > A: ICMP echo reply, seq 2, length 64
21:57:13.016580 IP (...)
A > target: ICMP echo request, seq 3, length 64
21:57:13.019251 IP (... id 3437 ...)
target > A: ICMP echo reply, seq 3, length 64
[1] TCP sessions uses a per flow ID generator not changed by this patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jeffrey Knockel <jeffk@cs.unm.edu>
Reported-by: Jedidiah R. Crandall <crandall@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two different ways to handle changes to sk->sk_dst
First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()
Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.
These ways are not inter changeable for a given socket type.
ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.
Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5dfb2 ("udp: ipv4: do not use
sk_dst_lock from softirq context")
In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 9cb3a50c5f ("ipv4: Invalidate the socket cached route on pmtu events if possible")
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, we would need to generate IP ID using a per destination IP
generator.
linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.
1) each inet_peer struct consumes 192 bytes
2) inetpeer cache uses a binary tree of inet_peer structs,
with a nominal size of ~66000 elements under load.
3) lookups in this tree are hitting a lot of cache lines, as tree depth
is about 20.
4) If server deals with many tcp flows, we have a high probability of
not finding the inet_peer, allocating a fresh one, inserting it in
the tree with same initial ip_id_count, (cf secure_ip_id())
5) We garbage collect inet_peer aggressively.
IP ID generation do not have to be 'perfect'
Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.
We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.
ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)
secure_ip_id() and secure_ipv6_id() no longer are needed.
Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
the value of itag is a random value from stack, and may not be initiated by
fib_validate_source, which called fib_combine_itag if CONFIG_IP_ROUTE_CLASSID
is not set
This will make the cached dst uncertainty
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, routing lookups used for Path PMTU Discovery in
absence of a socket or on unmarked sockets use a mark of 0.
This causes PMTUD not to work when using routing based on
netfilter fwmark mangling and fwmark ip rules, such as:
iptables -j MARK --set-mark 17
ip rule add fwmark 17 lookup 100
This patch causes these route lookups to use the fwmark from the
received ICMP error when the fwmark_reflect sysctl is enabled.
This allows the administrator to make PMTUD work by configuring
appropriate fwmark rules to mark the inbound ICMP packets.
Black-box tested using user-mode linux by pointing different
fwmarks at routing tables egressing on different interfaces, and
using iptables mangling to mark packets inbound on each interface
with the interface's fwmark. ICMPv4 and ICMPv6 PMTU discovery
work as expected when mark reflection is enabled and fail when
it is disabled.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my special case, when a packet is redirected from veth0 to lo,
its skb->dev->ifindex would be LOOPBACK_IFINDEX. Meanwhile we
pass the hard-coded LOOPBACK_IFINDEX to fib_validate_source()
in ip_route_input_slow(). This would cause the following check
in fib_validate_source() fail:
(dev->ifindex != oif || !IN_DEV_TX_REDIRECTS(idev))
when rp_filter is disabeld on loopback. As suggested by Julian,
the caller should pass 0 here so that we will not end up by
calling __fib_validate_source().
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend commit 13378cad02
("ipv4: Change rt->rt_iif encoding.") from 3.6 to return valid
RTA_IIF on 'ip route get ... iif DEVICE' instead of rt_iif 0
which is displayed as 'iif *'.
inet_iif is not appropriate to use because skb_iif is not set.
Use the skb->dev->ifindex instead.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RT_CACHE_STAT_INC macro triggers the new preemption checks
for __this_cpu ops.
I do not see any other synchronization that would allow the use of a
__this_cpu operation here however in commit dbd2915ce8 ("[IPV4]:
RT_CACHE_STAT_INC() warning fix") Andrew justifies the use of
raw_smp_processor_id() here because "we do not care" about races. In
the past we agreed that the price of disabling interrupts here to get
consistent counters would be too high. These counters may be inaccurate
due to race conditions.
The use of __this_cpu op improves the situation already from what commit
dbd2915ce8 did since the single instruction emitted on x86 does not
allow the race to occur anymore. However, non x86 platforms could still
experience a race here.
Trace:
__this_cpu_add operation in preemptible [00000000] code: avahi-daemon/1193
caller is __this_cpu_preempt_check+0x38/0x60
CPU: 1 PID: 1193 Comm: avahi-daemon Tainted: GF 3.12.0-rc4+ #187
Call Trace:
check_preemption_disabled+0xec/0x110
__this_cpu_preempt_check+0x38/0x60
__ip_route_output_key+0x575/0x8c0
ip_route_output_flow+0x27/0x70
udp_sendmsg+0x825/0xa20
inet_sendmsg+0x85/0xc0
sock_sendmsg+0x9c/0xd0
___sys_sendmsg+0x37c/0x390
__sys_sendmsg+0x49/0x90
SyS_sendmsg+0x12/0x20
tracesys+0xe1/0xe6
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ip_rt_dump do nothing after IPv4 route caches removal, so we can remove it.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4_ifdown_dst does nothing after IPv4 route caches removal,
so we can remove it.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit 89aef8921bf("ipv4: Delete routing cache."), the counter
in_slow_tot can't work correctly.
The counter in_slow_tot increase by one when fib_lookup() return successfully
in ip_route_input_slow(), but actually the dst struct maybe not be created and
cached, so we can increase in_slow_tot after the dst struct is created.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since commit 251da413("ipv4: Cache ip_error() routes even when not forwarding."),
the counter IPSTATS_MIB_INADDRERRORS can't work correctly, because the value of
err was always set to ENETUNREACH.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While forwarding we should not use the protocol path mtu to calculate
the mtu for a forwarded packet but instead use the interface mtu.
We mark forwarded skbs in ip_forward with IPSKB_FORWARDED, which was
introduced for multicast forwarding. But as it does not conflict with
our usage in unicast code path it is perfect for reuse.
I moved the functions ip_sk_accept_pmtu, ip_sk_use_pmtu and ip_skb_dst_mtu
along with the new ip_dst_mtu_maybe_forward to net/ip.h to fix circular
dependencies because of IPSKB_FORWARDED.
Because someone might have written a software which does probe
destinations manually and expects the kernel to honour those path mtus
I introduced a new per-namespace "ip_forward_use_pmtu" knob so someone
can disable this new behaviour. We also still use mtus which are locked on a
route for forwarding.
The reason for this change is, that path mtus information can be injected
into the kernel via e.g. icmp_err protocol handler without verification
of local sockets. As such, this could cause the IPv4 forwarding path to
wrongfully emit fragmentation needed notifications or start to fragment
packets along a path.
Tunnel and ipsec output paths clear IPCB again, thus IPSKB_FORWARDED
won't be set and further fragmentation logic will use the path mtu to
determine the fragmentation size. They also recheck packet size with
help of path mtu discovery and report appropriate errors.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPUs can ask for local route via ip_route_input_noref() concurrently.
if nh_rth_input is not cached yet, CPUs will proceed to allocate
equivalent DSTs on 'lo' and then will try to cache them in nh_rth_input
via rt_cache_route()
Most of the time they succeed, but on occasion the following two lines:
orig = *p;
prev = cmpxchg(p, orig, rt);
in rt_cache_route() do race and one of the cpus fails to complete cmpxchg.
But ip_route_input_slow() doesn't check the return code of rt_cache_route(),
so dst is leaking. dst_destroy() is never called and 'lo' device
refcnt doesn't go to zero, which can be seen in the logs as:
unregister_netdevice: waiting for lo to become free. Usage count = 1
Adding mdelay() between above two lines makes it easily reproducible.
Fix it similar to nh_pcpu_rth_output case.
Fixes: d2d68ba9fe ("ipv4: Cache input routes in fib_info nexthops.")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sockets marked with IP_PMTUDISC_INTERFACE won't do path mtu discovery,
their sockets won't accept and install new path mtu information and they
will always use the interface mtu for outgoing packets. It is guaranteed
that the packet is not fragmented locally. But we won't set the DF-Flag
on the outgoing frames.
Florian Weimer had the idea to use this flag to ensure DNS servers are
never generating outgoing fragments. They may well be fragmented on the
path, but the server never stores or usees path mtu values, which could
well be forged in an attack.
(The root of the problem with path MTU discovery is that there is
no reliable way to authenticate ICMP Fragmentation Needed But DF Set
messages because they are sent from intermediate routers with their
source addresses, and the IMCP payload will not always contain sufficient
information to identify a flow.)
Recent research in the DNS community showed that it is possible to
implement an attack where DNS cache poisoning is feasible by spoofing
fragments. This work was done by Amir Herzberg and Haya Shulman:
<https://sites.google.com/site/hayashulman/files/fragmentation-poisoning.pdf>
This issue was previously discussed among the DNS community, e.g.
<http://www.ietf.org/mail-archive/web/dnsext/current/msg01204.html>,
without leading to fixes.
This patch depends on the patch "ipv4: fix DO and PROBE pmtu mode
regarding local fragmentation with UFO/CORK" for the enforcement of the
non-fragmentable checks. If other users than ip_append_page/data should
use this semantic too, we have to add a new flag to IPCB(skb)->flags to
suppress local fragmentation and check for this in ip_finish_output.
Many thanks to Florian Weimer for the idea and feedback while implementing
this patch.
Cc: David S. Miller <davem@davemloft.net>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Half of the rt_cache_stat fields are no longer used after IP
route cache removal, lets shrink this per cpu area.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending out multicast messages, the source address in inet->mc_addr is
ignored and rewritten by an autoselected one. This is caused by a typo in
commit 813b3b5db8 ("ipv4: Use caller's on-stack flowi as-is in output
route lookups").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed last year [1], there is no compelling reason
to limit IPv4 MTU to 0xFFF0, while real limit is 0xFFFF
[1] : http://marc.info/?l=linux-netdev&m=135607247609434&w=2
Willem raised this issue again because some of our internal
regression tests broke after lo mtu being set to 65536.
IP_MTU reports 0xFFF0, and the test attempts to send a RAW datagram of
mtu + 1 bytes, expecting the send() to fail, but it does not.
Alexey raised interesting points about TCP MSS, that should be addressed
in follow-up patches in TCP stack if needed, as someone could also set
an odd mtu anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current net name space has only one genid for both IPv4 and IPv6, it has below
drawbacks:
- Add/delete an IPv4 address will invalidate all IPv6 routing table entries.
- Insert/remove XFRM policy will also invalidate both IPv4/IPv6 routing table
entries even when the policy is only applied for one address family.
Thus, this patch attempt to split one genid for two to cater for IPv4 and IPv6
separately in a fine granularity.
Signed-off-by: Fan Du <fan.du@windriver.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d2d68ba9 (ipv4: Cache input routes in fib_info nexthops)
assmued that "locally destined, and routed packets, never trigger
PMTU events or redirects that will be processed by us".
However, it seems that tunnel devices do trigger PMTU events in certain
cases. At least ip_gre, ip6_gre, sit, and ipip do use the inner flow's
skb_dst(skb)->ops->update_pmtu to propage mtu information from the
outer flows. These can cause the inner flow mtu to be decreased. If
next hop exceptions are not consulted for pmtu, IP fragmentation will
not be done properly for these routes.
It also seems that we really need to have the PMTU information always
for netfilter TCPMSS clamp-to-pmtu feature to work properly.
So for the time being, cache separate copies of input routes for
each next hop exception.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the uses of this unnecessary typedef.
Done via perl script:
$ git grep --name-only -w ctl_table net | \
xargs perl -p -i -e '\
sub trim { my ($local) = @_; $local =~ s/(^\s+|\s+$)//g; return $local; } \
s/\b(?<!struct\s)ctl_table\b(\s*\*\s*|\s+\w+)/"struct ctl_table " . trim($1)/ge'
Reflow the modified lines that now exceed 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern