PREEMPT_RT forces qcom-ipcc's handler to be threaded with interrupts
enabled, which triggers a warning in __handle_irq_event_percpu():
irq 173 handler irq_default_primary_handler+0x0/0x10 enabled interrupts
WARNING: CPU: 0 PID: 77 at kernel/irq/handle.c:161 __handle_irq_event_percpu+0x4c4/0x4d0
Mark it IRQF_NO_THREAD to avoid running the handler in a threaded
context with threadirqs or PREEMPT_RT enabled.
Signed-off-by: Eric Chanudet <echanude@redhat.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
There is a spelling mistake in a pr_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
dma_map_sg return 0 on error, fix the error check, and return -EIO
to caller.
Fixes: dbc049eee7 ("mailbox: Add driver for Broadcom FlexRM ring manager")
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
IPQ8074 has the APSS clock controller utilizing the same register space as
the APCS, so provide access to the APSS utilizing a child device like
IPQ6018.
IPQ6018 and IPQ8074 use the same controller and driver, so just utilize
IPQ6018 match data for IPQ8074.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The mailbox offset is not only used for receiving messages, but it is
also used by messages sent to the system controller by Linux that have a
payload, such as the "digital signature service". It is also overloaded
by certain other services (reprogramming of the FPGA fabric, see Link:)
to have a meaning other than the offset the system controller should
read from.
When the driver was written, no such services of the latter type were
in use & those of the former used an offset of zero so this has gone
un-noticed.
Link: https://www.microsemi.com/document-portal/doc_download/1245815-polarfire-fpga-and-polarfire-soc-fpga-system-services-user-guide # Section 5.2
Fixes: 83d7b15608 ("mbox: add polarfire soc system controller mailbox")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The "data" region of the PolarFire SoC's system controller mailbox is
not one continuous register space - the system controller's QSPI sits
between the control and data registers. Split the "data" reg into two
parts: "data" & "control". Optionally get the "data" register address
from the 3rd reg property in the devicetree & fall back to using the
old base + MAILBOX_REG_OFFSET that the current code uses.
Fixes: 83d7b15608 ("mbox: add polarfire soc system controller mailbox")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Because IMX_MU_xCR_MAX was increased to 5, some mu cfgs were not updated
to include the CR register. Add the missed CR register to xcr array.
Fixes: 82ab513bae ("mailbox: imx: support RST channel")
Reported-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Liu Ying <victor.liu@nxp.com> # i.MX8qm/qxp MEK boards boot
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This allows clients running in atomic context to poll for messages to
arrive.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This allows clients to use the atomic-safe mailbox API style.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
During MU initialization, there maybe pending GSR and RSR pending
interrupt, clear them to avoid unexpected kernel dump when requesting
mailbox channel
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX generic MU supports MU-A/B reset feature.
When stop/start remotecore, MU is not reset. So when Linux stop
remotecore, the MU-B side BCR may contain valid configuration,
because MU-B is not reset. So when linux start Mcore
again and notify Mcore, Mcore is not ready to handle MU interrupt
and cause issues. So need reset MU when stop Mcore.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
rx_callback is a standard mailbox callback mechanism and could cover the
function of proprietary cmdq_task_cb, so use the standard one instead of
the proprietary one. Client driver has changed to use standard
rx_callback, so remove proprietary cmdq_task_cb.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PM_SLEEP is not set, there is a warning that
qcom_ipcc_pm_resume() is unused:
drivers/mailbox/qcom-ipcc.c:258:12: error: 'qcom_ipcc_pm_resume' defined but not used [-Werror=unused-function]
258 | static int qcom_ipcc_pm_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Commit 1a3c7bb088 ("PM: core: Add new *_PM_OPS macros, deprecate old
ones") reworked the PM_OPS macros to avoid this problem. Use
NOIRQ_SYSTEM_SLEEP_PM_OPS directly so that qcom_ipcc_pm_resume() always
appears to be used to the compiler, even though it will be dead code
eliminated in the !CONFIG_PM_SLEEP case.
Fixes: c25f778997 ("mailbox: qcom-ipcc: Log the pending interrupt during resume")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This reverts commit c7dacf5b0f,
"mailbox: avoid timer start from callback"
The previous commit was reverted since it lead to a race that
caused the hrtimer to not be started at all. The check for
hrtimer_active() in msg_submit() will return true if the
callback function txdone_hrtimer() is currently running. This
function could return HRTIMER_NORESTART and then the timer
will not be restarted, and also msg_submit() will not start
the timer. This will lead to a message actually being submitted
but no timer will start to check for its compleation.
The original fix that added checking hrtimer_active() was added to
avoid a warning with hrtimer_forward. Looking in the kernel
another solution to avoid this warning is to check hrtimer_is_queued()
before calling hrtimer_forward_now() instead. This however requires a
lock so the timer is not started by msg_submit() inbetween this check
and the hrtimer_forward() call.
Fixes: c7dacf5b0f ("mailbox: avoid timer start from callback")
Signed-off-by: Björn Ardö <bjorn.ardo@axis.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Enable logging of the pending interrupt that triggered device wakeup. This
logging information helps to debug IRQs that cause periodic device wakeups
by printing the detailed information of pending IPCC interrupts.
Scenario: Device wakeup caused by Modem crash
Logs:
qcom-ipcc mailbox: virq: 182 triggered client-id: 2; signal-id: 2
From the IPCC bindings it can further be understood that the client here is
IPCC_CLIENT_MPSS and the signal was IPCC_MPROC_SIGNAL_SMP2P.
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Prasad Sodagudi <quic_psodagud@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
`pcc_mailbox_probe` doesn't initialize all memory that has been allocated
before the first time that one of it's members `txdone_irq` may be
accessed.
This leads to a an invalid load any time that this member is accessed:
[ 2.429769] UBSAN: invalid-load in drivers/mailbox/pcc.c:684:22
[ 2.430324] UBSAN: invalid-load in drivers/mailbox/mailbox.c:486:12
[ 4.276782] UBSAN: invalid-load in drivers/acpi/cppc_acpi.c:314:45
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215587
Fixes: ce028702dd ("mailbox: pcc: Move bulk of PCCT parsing into pcc_mbox_probe")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Correct kerneldoc warnings like:
drivers/mailbox/arm_mhu_db.c:47:
warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/mailbox/qcom-ipcc.c:58:
warning: Function parameter or member 'num_chans' not described in 'qcom_ipcc'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ran jianping <ran.jianping@zte.com.cn>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ran jianping <ran.jianping@zte.com.cn>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add support for 128-bit shared mailboxes found on Tegra234 chips.
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The list iterator is always non-NULL so it doesn't need to be checked.
Thus just remove the unnecessary NULL check.
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Smatch reports this issue
imx-mailbox.c:887:10: warning: Initializer entry defined twice
imx-mailbox.c:889:10: also defined here
.rxdb = imx_mu_generic_rxdb,
Is listed twice, so remove one.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
During the system suspend path we must set all queues to operate in
polled mode as it is possible for any protocol built using this mailbox,
such as TISCI, to require communication during the no irq phase of suspend,
and we cannot rely on interrupts there.
Polled mode is implemented by allowing the mailbox user to define an
RX channel as part of the message that is sent which is what gets polled
for a response. If polled mode is enabled, this will immediately be
polled for a response at the end of the mailbox send_data op before
returning success for the data send or timing out if no response is
received.
Finally, to ensure polled mode is always enabled during system suspend,
iterate through all queues to set RX queues to polled mode during system
suspend and disable polled mode for all in the resume handler.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Refactor the portion of code that actually reads received messages from
a queue into its own function, ti_msgmgr_queue_rx_data, that is called
by the interrupt handler instead of reading directly from the handler.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX93 S401 MU support two interrupts: tx empty and rx full.
- Introduce a new flag IMX_MU_V2_IRQ for the dual interrupt case
- Update Copyright
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
To i.MX93 S401 MU, there are two interrupts: rx full and tx empty.
So extend irq to an array to prepare i.MX93 S401 MU support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX8/8X SECO firmware IPC is an implementation of passing messages.
But current imx-mailbox driver only support one word message,
i.MX8/8X linux side firmware has to request four TX, four RX and a
TXDB to support IPC to SECO firmware. This is low efficent and
more interrupts triggered compared with one TX and one RX.
To make SECO MU work,
- parse the size of msg.
- Only enable TR0/RR0 interrupt for transmit/receive message.
- For TX/RX, only support one TX channel and one RX channel
- For RX, support receive msg of any size, limited by hardcoded value
of 30.
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add a rxdb callback to prepare for i.MX8 SECO MU rxdb which has a
different logic.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Mailbox driver needs to wait and read all the words in response to a
SCFW API call, else the protocol gets messed up and results in kernel hang.
When the responses are longer than 3 words its possible that SCFW will
take some time to fill up the rest of the words in the MU, a timeout of
100us is arbritrary and too short. While waiting for Linux to consume the
first 3 words of the response SCFW can be busy doing other stuff and hence
Linux needs to wait for the rest of the words.
Similar restriction applies when writing messages that are longer than
3 words.
This patch increases the timeout to 5secs while waiting for response
or writing long messages to SCFW.
Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
check 'priv->clk' before 'imx_mu_read()' otherwise crash happens on
i.mx8ulp, since clock not enabled.
Fixes: 4f0b776ef5 ("mailbox: imx-mailbox: support i.MX8ULP MU")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Since IRQF_NO_SUSPEND used for imx mailbox driver, that means this irq
can't be used for wakeup source so that can't wakeup from freeze mode.
Add pm_system_wakeup() to wakeup from freeze mode.
Fixes: b7b2796b9b31e("mailbox: imx: ONLY IPC MU needs IRQF_NO_SUSPEND flag")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch is to for MediaTek ADSP IPC mailbox controller driver
It is used to send short messages between processors with adsp
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
MSM8976 APCS block is similar to one found in MSM8994.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The txdone can re-fill the mailbox. Keep polling the mailbox during the
flush until all the messages have been delivered.
This fixes an issue with the Tegra Combined UART (TCU) where output can
get truncated under high traffic load.
Signed-off-by: Pekka Pessi <ppessi@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 91b1b1c3da ("mailbox: tegra-hsp: Add support for shared mailboxes")
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
Use IRQF_NO_SUSPEND flag instead of enable_irq_wake to
support interrupt wake up from suspend.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Since hardware is supporting multiple IPCC instance,
use ipcc_%d instead of ipcc as the irq name to support
in driver.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Dynamic alloc for channel arrangement instead of static alloced
array, it is more flexible and can reduce memory usage.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The Polarfire SoC is currently using two different compatible string
prefixes. Fix this by changing "polarfire-soc-*" strings to "mpfs-*" in
its system controller in order to match the compatible string used in
the soc binding and device tree.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Smatch static checker warns:
| drivers/mailbox/pcc.c:292 pcc_mbox_request_channel()
| error: uninitialized symbol 'dev'.
Fix the same by using pr_err instead of dev_err as the variable 'dev'
is uninitialized at that stage.
Fixes: ce028702dd ("mailbox: pcc: Move bulk of PCCT parsing into pcc_mbox_probe")
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix following coccicheck warning:
WARNING: Function "for_each_child_of_node"
should have of_node_put() before return.
Early exits from for_each_child_of_node should decrement the
node reference counter.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix following coccicheck warning:
WARNING: Function "for_each_available_child_of_node"
should have of_node_put() before return.
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The devm_kzalloc() function does not return error pointers, it returns
NULL on failure.
Fixes: 97961f78e8 ("mailbox: imx: support i.MX8ULP S4 MU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Eric Chanudet