We have a use case with the da850 SATA controller where at PLL0
frequency of 456MHz (needed to properly service the LCD controller)
the chip becomes unstable and the hardreset operation is ignored the
first time 50% of times.
The sata core driver already retries to resume the link because some
controllers ignore writes to the SControl register, but just retrying
the resume operation doesn't work - we need to issue he phy/wake reset
again to make it work.
Reimplement ahci_hardreset() in the driver and poke the controller a
couple times before really giving up.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need a way to retrieve the information about the online state of
the link in the ahci-da850 driver.
Create a new function: ahci_do_hardreset() which is called from
ahci_hardreset() for backwards compatibility, but has an additional
argument: 'online' - which can be used to check if the link is online
after this function returns.
The new routine will be used in the ahci-da850 driver to avoid code
duplication when implementing a workaround for tha da850 SATA
controller quirk/instability.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There's an issue with the da850 SATA controller: if port multiplier
support is compiled in, but we're connecting the drive directly to
the SATA port on the board, the drive can't be detected.
To make SATA work on the da850-lcdk board: first try to softreset
with pmp - if the operation fails with -EBUSY, retry without pmp.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We're using device tree for da850-lcdk. Add the match table to allow
to probe the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In preparation for using two clocks in the driver (the sysclk2-based
clock and the external REFCLK), check if we got the functional clock
after calling ahci_platform_get_resources(). If not, retry calling
clk_get() with con_id specified.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The SB600 and SB700 southbridge chips from ATI/AMD only have
connections for the primary IDE port. As these chips have unique
pci device ID's use these to mark the secondary port as 'dummy'
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata-sff.c checks for legacy mode by testing if both primary and
secondary ports on a controller are in legacy mode and selects legacy
if either one is. However on some south bridge chips (e.g AMD
SB600/SB700) the secondary port is not wired, and when it is disabled
by setting the disable bit in the PCI header it appears as a fixed
legacy port.
Prevent incorrect detection by not testing ports that are marked as
'dummy'
tj: Addressed Sergei's review points. Other style edits.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
@t1 and @t2i are calculated along with @t2 but never used. Drop them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Binderman <dcb314@hotmail.com>
Ls2088a is new introduced arm-based soc with sata support with
following features:
1. Complies with the serial ATA 3.0 specification and the AHCI 1.3.1
specification
2. Contains a high-speed descriptor-based DMA controller
3. Supports the following:
a. Speeds of 1.5 Gb/s (first-generation SATA), 3 Gb/s
(second-generation SATA), and 6 Gb/s (third-generation SATA)
b. FIS-based switching
c. Native command queuing (NCQ) commands
d. Port multiplier operation
e. Asynchronous notification
f. SATA BIST mode
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For ls1021a, and armv8 chasis 2 socs, sata ecc must be disabled.
If ecc register is not found in sata node in dts, report error.
This is a chip erratum described as bellow:
The Read DMA operations get early termination indication from the
controller. This issue is observed as CRC error in the status registers.
The issue is due to address collision at address 0 in the dual port
memory. The read is a dummy read to flush out the header, but due to
collision the controller logs the mbit error reported by the ECC check
logic. This results in the early termination of the Read DMA operation
by the controller. The issue happens to all the interface
speeds(GEN1/2/3) for all the products.
Workaround:
Disable ECC feature on those platforms.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Enable DMA coherence in SATA controller on condition that
dma-coherent property exists in sata node in DTS.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit a234f7395c.
The commit tried to get rid of the shared global SCSI response buffer.
Unfortunately, it added blocking allocation to atomic path. Revert it
for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
When CONFIG_HWMON is disabled, we now get a link failure:
ERROR: "devm_hwmon_device_register_with_groups" [drivers/ata/ahci_imx.ko] undefined!
drivers/ata/ahci_imx.o: In function `imx_ahci_probe':
ahci_imx.c:(.text.imx_ahci_probe+0x304): undefined reference to `devm_thermal_zone_of_sensor_register'
This makes the code calling into the hwmon subsystem compile-time
conditional, and adds a Kconfig dependency to avoid the corner
case of having HWMON=m and AHCI_IMX=y, by forcing AHCI_IMX=m in this
case. The thermal subsystem already has a check in its header, but
that also doesn't cover the THERMAL=m case, so we need a somewhat
complex Kconfig expression to handle all cases.
Fixes: 54643a83b4 ("ahci: imx: Add imx53 SATA temperature sensor support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add Atari Falcon PATA controller driver. The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode and thus avoiding the need for STDMA
locking magic altogether.
Tested under ARAnyM emulator.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For Atari Falcon PATA support we need to check the current command
in its ->sff_data_xfer method. Update core code and all users
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When libata was merged m68k lacked IOMAP support. This has not been
true for a long time now so allow subsystem to be used on m68k.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Note of the emulated commands in the pageout/pagein path, so just do
a GFP_NOIO dynamic allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
No need to copy a zeroed buffer to the caller if the command is defined
to not have a response in the SCSI spec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We always need to call ->scsi_done after we've finished emulating a
command, so do it in a single place at the end of ata_scsi_simulate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
It's always the scsi_done callback, and we can get at that easily
in the place where ->done is called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
It's only used in libata-scsi.c, so move it closer to the users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We only need to look at 4 bytes of the inquiry response for ATAPI
devices. Instead of using the global ata_scsi_rbuf just use a
a stack buffer. Also factor the fixup into it's own little helper
function to make it more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replace the sparse 256-pointer array for looking up protocol strings by
a switch() statement to reduce kernel size.
According to bloat-o-meter, this saves 910 bytes on m68k (32-bit), and
1892 bytes on arm64 (64-bit).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert to devm_ioremap_resource() which provides more consistent error
handling.
Note that devm_ioremap_resource() provides its own error messages.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
For an ATA device supporting the sense data reporting feature set, a
failed command will trigger the execution of ata_eh_request_sense if
the result task file of the failed command has the ATA_SENSE bit set
(sense data available bit). ata_eh_request_sense executes the REQUEST
SENSE DATA EXT command to retrieve the sense data of the failed
command. On success of REQUEST SENSE DATA EXT, the ATA_SENSE bit will
NOT be set (the command succeeded) but ata_eh_request_sense
nevertheless tests the availability of sense data by testing that bit
presence in the result tf of the REQUEST SENSE DATA EXT command. This
leads us to falsely assume that request sense data failed and to the
warning message:
atax.xx: request sense failed stat 50 emask 0
Upon success of REQUEST SENSE DATA EXT, set the ATA_SENSE bit in the
result task file command so that sense data can be returned by
ata_eh_request_sense.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Add a hwmon entry to get the temperature from the die of imx53
SATA.
The original patch was made by Richard Zhu for kernel 2.6.x:
ENGR00134041-MX53-Add-the-SATA-AHCI-temperature-monitor.patch
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Marko reports that CX1-JB512-HP shows the same timeout issues as
CX1-JB256-HP. Let's apply MAX_SEC_128 to all devices in the series.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marko Koski-Vähälä <marko@koski-vahala.com>
Cc: stable@vger.kernel.org # v3.19+
acpi_get_object_info() allocates the returned structure, which the
caller has to free when the call succeeds. Free it when appropriate.
Fixes: c9802a4be6 ("ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.")
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Tejun Heo <tj@kernel.org>
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/ata/libata.ko] undefined!
To fix this, protect the DMA code by #ifdef CONFIG_HAS_DMA, and provide
dummies of ata_sg_clean() and ata_sg_setup() for the !CONFIG_HAS_DMA
case.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 70e6ad0c6d ("[PATCH] libata: prepare ata_sg_clean() for
invocation from EH") made ata_sg_clean() global, but no user outside
libata-core.c has ever materialized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull another libata patch from Tejun Heo:
"One more patch from Adam added.
It makes libata skip probing for NCQ prio unless the feature is
explicitly requested by the user. This is necessary because some
controllers lock up after the optional feature is probed"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: avoid probing NCQ Prio Support if not explicitly requested
Previously, when the ata device was being initialized we were
probing for NCQ prio support by checking the identify information
and also checking the log page that holds information about ncq prio
support.
This caused an error on an Intel HBA so the code is now updated to
only probe for NCQ prio support when the sysfs variable controlling
NCQ prio support is enabled.
tj: Update formatting, switch to spin_[un]lock_irq() and update
locking a bit, use REVALIDATE instead of RESET, and return -EIO
instead of -EINVAL on config failure.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Adam added opt-in ATA command priority support.
- There are machines which hide multiple nvme devices behind an ahci
BAR. Dan Williams proposed a solution to force-switch the mode but
deemed too hackishd. People are gonna discuss the proper way to
handle the situation in nvme standard meetings. For now, detect and
warn about the situation.
- Low level driver specific changes.
Christoph Hellwig pipes in about the hidden nvme warning:
"I wish that was the case. We've pretty much agreed that we'll want to
implement it as a virtual PCIe root bridge, similar to Intels other
'innovation' VMD that we work around that way.
But Intel management has apparently decided that they don't want to
spend more cycles on this now that Lenovo has an optional BIOS that
doesn't force this broken mode anymore, and no one outside of Intel
has enough information to implement something like this.
So for now I guess this warning is it, until Intel reconsideres and
spends resources on fixing up the damage their Chipset people caused"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: warn about remapped NVMe devices
ahci-remap.h: add ahci remapping definitions
nvme: move NVMe class code to pci_ids.h
pata: imx: support controller modes up to PIO4
pata: imx: add support of setting timings for PIO modes
pata: imx: set controller PIO mode with .set_piomode callback
pata: imx: sort headers out
ata: set ncq_prio_enabled iff device has support
ata: ATA Command Priority Disabled By Default
ata: Enabling ATA Command Priorities
block: Add iocontext priority to request
ahci: qoriq: added ls1046a platform support
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----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=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
SCT Write Same support had been introduced with
commit 7b20309428 ("libata: Add support for SCT Write Same")
Some problems, namely excessive userspace segfaults, had been reported at
http://lkml.kernel.org/r/20160908192736.GA4356@gmail.com
This lead to commit 0ce1b18c42 ("libata: Some drives failing on
SCT Write Same") which strived to disable SCT Write Same on !ZAC devices.
Due to the way this was done and to the logic in sd_config_write_same(),
this didn't work for those devices that have
->max_ws_blocks > SD_MAX_WS10_BLOCKS: for these, ->no_write_same and
->max_write_same_sectors would still be non-zero,
but ->ws10 == ->ws16 == 0. This would cause sd_setup_write_same_cmnd() to
demultiplex REQ_OP_WRITE_SAME requests to WRITE_SAME, and these in turn
aren't supported by libata-scsi:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2625094 at
logical offset 2032 with max blocks 2 with error 121
EXT4-fs (dm-1): This should not happen!! Data will be lost
121 == EREMOTEIO is what scsi_io_completion() asserts in case of
invalid opcodes.
Back to the original problem of userspace segfaults: this can be tracked
down to ata_format_sct_write_same() overwriting the input page. Sometimes,
this page is ZERO_PAGE(0) which ceases to be filled with zeros from that
point on. Since ZERO_PAGE(0) is used for userspace .bss mappings, code of
the following is doomed:
static char *a = NULL; /* .bss */
...
if (a)
*a = 'a';
This problem is not solved by disabling SCT Write Same for !ZAC devices
only.
It can certainly be fixed, but the final release is quite close -- so
disable SCT Write Same for all ATA devices rather than introducing some
SCT key buffer allocation schemes at this point.
Fixes: 7b20309428 ("libata: Add support for SCT Write Same")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some Intel ahci implementations have a completely broken remapping mode
where they hide one or more NVMe devices behind the bar of an AHCI device.
Intel refuses to let the OS reprogram the BIOS to switch out of this
mode at runtime, and so far we're not come up with another good way
to undo the mess that the Chipset people created. So for now the only
thing we can do is to alert users about this situation and switch to the
faster and much saner so called "AHCI" mode insted of the RAID mode in
the BIOS so that the BIOS does not hide the NVMe devices from us.
The sitation is even worse as at least one vendor (thanks a lot Lenovo..)
has started hardcoding their BIOS into the "RAID" mode even for laptops
that don't use AHCI _at all_ and just have a single NVMe device. For now
there is an unspported Linux-only BIOS that undoes this braindamage,
but we'll have to see if things are getting better or worse from here.
Based on an earlier patch from Dan Williams <dan.j.williams@intel.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the nr-ports property is missing ata_host_alloc_pinfo is called with
n_ports = 0. This results in host->ports[0] = NULL which later makes
mv_init_host() oops when dereferencing this pointer.
Instead be a bit more cooperative and fail the probing with an error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Don't try to guess what the errors from pci_irq_alloc_vectors mean, as
that's too fragile. Instead always try allocating a single vector
when multi-MSI mode fails. This makes various intel Desktop and
Laptop CPUs use MSI again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Michael Marley <michael@michaelmarley.com>
Tested-by: Michael Marley <michael@michaelmarley.com>
Fixes: 0b9e2988ab ("ahci: use pci_alloc_irq_vectors")
Signed-off-by: Tejun Heo <tj@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
Having timing settings for all supported by the controller PIO modes
now it is possible to expand its PIO mask.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The controller is capable to operate in up to PIO4 mode, however
before the change the driver relies on timing settings done by
a bootloader for PIO0 mode only. The change adds more flexibility
in PIO mode selection at runtime and makes the driver to work even if
bootloader does not preset ATA timings.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert .set_mode callback function to more specific .set_piomode,
the driver does not have support of DMA modes, thus a simpler version
of the callback is preferred.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There's a typo in ata_gen_passthru_sense(), where the first byte
would be overwritten incorrectly later on.
Reported-by: Charles Machalow <csm10495@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Fixes: 11093cb1ef ("libata-scsi: generate correct ATA pass-through sense")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
We need to make sure hpriv->irq is set properly if we don't use per-port
vectors, so switch from blindly assigning pdev->irq to using
pci_irq_vector, which handles all interrupt types correctly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Robert Richter <robert.richter@cavium.com>
Tested-by: Robert Richter <robert.richter@cavium.com>
Tested-by: David Daney <ddaney.cavm@gmail.com>
Fixes: 0b9e2988ab ("ahci: use pci_alloc_irq_vectors")
Signed-off-by: Tejun Heo <tj@kernel.org>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
commit 17a51f12 ("ahci: only try to use multi-MSI mode if there is more
than 1 port") lead to a case where nvec isn't initialized before it's
used. Fix this by moving the check into the n_ports conditional.
Reported-and-reviewed-by Colin Ian King <colin.king@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We previously had a check to see if the device has support for
prioritized ncq commands and a check to see if a device flag
is set, through a sysfs variable, in order to send a prioritized
command.
This patch only allows the sysfs variable to be set if the device
supports prioritized commands enabling one check in ata_build_rw_tf
in order to determine whether or not to send a prioritized command.
This patch depends on ata: ATA Command Priority Disabled By Default
tj: Minor subject and formatting updates.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a sysfs entry to turn on priority information being passed
to a ATA device. By default this feature is turned off.
This patch depends on ata: Enabling ATA Command Priorities
tj: Renamed ncq_prio_on to ncq_prio_enable and removed trivial
ata_ncq_prio_on() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch checks to see if an ATA device supports NCQ command priorities.
If so and the user has specified an iocontext that indicates
IO_PRIO_CLASS_RT then we build a tf with a high priority command.
This is done to improve the tail latency of commands that are high
priority by passing priority to the device.
tj: Removed trivial ata_ncq_prio_enabled() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We should only try to allocate multiple MSI or MSI-X vectors if the device
actually has multiple ports. Otherwise pci_alloc_irq_vectors will return
a single vector due to n_ports = 1, in which case we shouldn't set the
AHCI_HFLAG_MULTI_MSI flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 0b9e2988 ("ahci: use pci_alloc_irq_vectors")
Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Tested-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 640847298e ("ahci: qoriq: Disable NCQ
on ls2080a SoC")
The erratum has been fixed in ls2080a v2.0 and later soc.
In reality, customer will not get any ls2080a v1.0 soc. Neither apply
to any products. So reverting this commit won't create any side effect.
Blacklisting v2.0 could also be a option, but that needs to check the
soc version which is not suitable in the driver.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replacing dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Harman Kalra <harman4linux@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Restrict support SCT Write Same to devices which also support ZAC where
support is required.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the new pci_alloc_irq_vectors API to allocate MSI-X and MSI vectors.
The big advantage over the old code is that we can use the same API for
MSI and MSI-X, and that we don't need to store the MSI-X vector mapping
in driver-private data structures.
This first conversion keeps the probe order as-is: MSI-X multi vector,
MSI multi vector, MSI single vector, MSI-X single vector and last a
single least legacy interrupt line. There is one small change of
behavior: we now check the "MSI Revert to Single Message" flag for
MSI-X in addition to MSI.
Because the API to find the Linux IRQ number for a MSI/MSI-X vector
is PCI specific, but libahaci is bus-agnostic I had to a
get_irq_vector function pointer to struct ahci_host_priv. The
alternative would be to move the multi-vector case of ahci_host_activate
to ahci.c and just call ata_host_activate directly from the others
users of ahci_host_activate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ninja32 needs to set some flags to indicate it does 32bit IO. However it currently assigns this which
loses the initializing flag and causes a warning spew. Fix it to use a logical or as is intended.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Ellmar Stelnberger <estellnb@elstel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use non DMA write log when ATA_DFLAG_PIO is set.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Correct handling of devices with sector_size other that 512 bytes.
In the case of a 4Kn device sector_size it is possible to describe a much
larger DSM Trim than the current fixed default of 512 bytes.
This patch assumes the minimum descriptor is sector_size and fills out
the descriptor accordingly.
The ACS-2 specification is quite clear that the DSM command payload is
sized as number of 512 byte transfers so a 4Kn device will operate
correctly without this patch.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Acked-by: Tejun Heo <tj@kernel.org>
SATA drives may support write same via SCT. This is useful
for setting the drive contents to a specific pattern (0's).
Translate a SCSI WRITE SAME 16 command to be either a DSM TRIM
command or an SCT Write Same command.
Based on the UNMAP flag:
- When set translate to DSM TRIM
- When not set translate to SCT Write Same
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Safely overwriting the attached page to ATA format from the SCSI formatted
variant.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
irq already contains the interrupt number for the port, don't add the
port index to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d684a90d38 ("ahci: per-port msix support")
Cc: stable@vger.kernel.org v4.5+
Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force_port_map to 1 by using ports-implemented
DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
By default the SATA IP on the qoriq SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
In addition, the dma-coherent property must be set on the
SATA controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
scsi_done() was called repeatedly and apparently because of that,
the kernel would call trace when we touch the Control mode page:
Call Trace:
[<ffffffff812ea0d2>] dump_stack+0x63/0x81
[<ffffffff81079cfb>] __warn+0xcb/0xf0
[<ffffffff81079e2d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa00f51b0>] ata_eh_finish+0xe0/0xf0 [libata]
[<ffffffffa00fb830>] sata_pmp_error_handler+0x640/0xa50 [libata]
[<ffffffffa00470ed>] ahci_error_handler+0x1d/0x70 [libahci]
[<ffffffffa00f55f0>] ata_scsi_port_error_handler+0x430/0x770 [libata]
[<ffffffffa00eff8d>] ? ata_scsi_cmd_error_handler+0xdd/0x160 [libata]
[<ffffffffa00f59d7>] ata_scsi_error+0xa7/0xf0 [libata]
[<ffffffffa00913ba>] scsi_error_handler+0xaa/0x560 [scsi_mod]
[<ffffffffa0091310>] ? scsi_eh_get_sense+0x180/0x180 [scsi_mod]
[<ffffffff81098eb8>] kthread+0xd8/0xf0
[<ffffffff815d913f>] ret_from_fork+0x1f/0x40
[<ffffffff81098de0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 8b7501047e928a17 ]---
Removed the unnecessary code and let ata_scsi_translate() do the job.
Also, since ata_mselect_control() has no ATA command to send to the
device, ata_scsi_mode_select_xlat() should return 1 for it, so that
ata_scsi_translate() will finish early to avoid ata_qc_issue().
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_mselect_*() would initialize a char array for storing a copy of
the current mode page. However, char could be signed char. In that
case, bytes larger than 127 would be converted to negative number.
For example, 0xff from def_control_mpage[] would become -1. This
prevented ata_mselect_control() from working at all, since when it
did the read-only bits check, there would always be a mismatch.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=8lmX
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
Pull libata fix from Tejun Heo:
"Another fallout from max_sectors bump a couple years ago. The lite-on
optical drive times out on large requests"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: LITE-ON CX1-JB256-HP needs lower max_sectors
`changeable` is the "version" of mode page requested by the user.
It will be less confusing/misleading if we do not check it
"together" with the setting bits of the drive.
Not to mention that we currently have ata_mselect_*() implemented
in a way that each of them will serve exclusively a particular bit
on each page. The old style will hence make the condition look even
more unnecessarily arcane if the ata_msense_*() is reflecting more
than one bit.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to PCI subsystem behaviour, unloading AHCI driver will disable
MSI and enable INTx. When HBA supports MSIx or Multiple MSI, Driver's
irq handler doesn't clear GHC.IS register. It works well when reading or
writing data and GHC.IS is always non-zero. But when unloading driver
(or any other operation which causes disable MSIx and enable INTx), PCI
subsystem uses config write(Rx04.bit10) to enable INTx. Because
GHC.IS is non-zero, HBA will falsely assume some port needs interrupt
service. Then it asserts INTx. To make things worse, when AHCI controller
shares the same interrupt pin with other PCI device, that PCI device's ISR
will be called and nobody de-asserts previous INTx.
This patch clears GHC.IS in ahci_port_stop() even when using MSIx or
MMSI to prevent this case. It ensures GHC.IS is zero before PCI subsystem
enables INTx.
tj: Minor updates to the comment.
Signed-off-by: Raymond Pang <raymond_rule@hotmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
This avoid the need to always translate between the two in ata_prot_flags
and generally cleans up the taskfile protocol usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The reset_all variable name is misleading as this bit is also applicable to
open, close, and finish actions. So rename that variable to "all" and remove
the unnecessary mask operation that's already done earlier.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split from the previous patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The subcommand for NCQ NON-DATA must be specified in the feature
(low byte), not the high-order count byte. Also make sure to properly
cast the all bit to a u16 before shiting it by 8 to avoid undefined
behavior.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split the original patch into two, updated changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Include reporting options when translating REPORT ZONES commmand to
ATA NCQ, and make sure we only look at the actually specified bits
in the CDB for the options.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: update patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a new taskfile protocol ATA_PROT_NCQ_NODATA to handle
ATA NCQ NO-DATA commands correctly.
And fixup ata_scsi_zbc_out_xlat() to use it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some taskfile protocol values where missing in ata_eh_link_report().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The taskfile protocol is a numeric value, and can not be ORed. Currently
this is harmless as the protocol is always zeroed before, but if it ever
has a non-zero value the ORing would create incorrect results.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[hch: updated patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use accessor functions instead of the raw value.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently libata statically allows only 1-block (512-byte) payload
for each TRIM command. Each payload can carry 64 TRIM ranges since
each range requires 8 bytes.
It is silly to keep doing the calculation (512 / 8) in different
places. Hence, define the new ATA_MAX_TRIM_RNUM for the result.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently if a WRITE SAME (16) command is issued to the SATL with
"number of blocks" that is larger than the "Maximum write same length"
(which is the maximum number of blocks per TRIM command allowed in
libata, currently 65535 * 512 / 8 blocks), the SATL will accept the
command and translate it to a TRIM command with the upper limit.
However, according to SBC (as of sbc4r11.pdf), the "device server"
should terminate the command with "Invalid field in CDB" in that case.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
To make it consistent with the recently added ata_mselect_control().
We probably shouldn't have the word "mode" in its name anyway, since
that's not the case for other ata_msense_*() / ata_mselect_*() either.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The bit should always be set to 1 when the requested version of
page is "changeable" because we've made it so in ata_mselect_control().
Also, it should always be set to 1 if ATA_DFLAG_D_SENSE is set (when
the requested version of page is "current" or "default").
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
According to the HPT366 data sheet, PCI config space dword 0x40-0x43
bits 11:8 specify the primary drive cmd_high_time, however,
currently just 3 bits of the 4 are being used because the mask
is 0x700 and not 0x0f00. Fix the mask, allowing for the 40MHz clock
to be detected.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The comment suggests we should be having an SPC-3 version descriptor
but the 0260h is the code for "SPC-2 (no version claimed)". Correct
it to 0300h so that it has the "SPC-3 (no version claimed)" descriptor.
Note that we are claiming SPC-3 version compatibility in the VERSION
field of the standard INQUIRY data. Therefore, I assume the typo was
on the code but not on the comment.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Avoid performance bottleneck when being SCSI pass-through'd to
virtual machines with other OSes (e.g. Windows) via virtio-scsi
and scsi-block in qemu.
Ref.: https://github.com/YanVugenfirer/kvm-guest-drivers-windows/issues/63
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Without this fix, the DRA bit of the caching mode page would not
be updated when the read look-ahead feature is toggled (e.g. with
`smartctl --set`), but will only be until, for example, the write
cache feature is touched.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 856c466393 ("libata: support device-managed ZAC devices")
had the line that "bumps" the VERSION field in standard INQUIRY data
removed. Add it back and claim SPC-5 version compatibility, which
matches with the current version descriptor "SPC-5 (no version claimed)"
that is used for ZAC devices.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It does not make sense and is confusing to respond with "Invalid
field in CDB" while we have no support at all implemented for
FORMAT UNIT. It is decent to let it go to the default, which
will respond with "Invalid command operation code" instead.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Two trivial fixes - one for a bug in the allocation failure path and
the other a compiler warning fix"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: sata_mv: fix mis-conversion in mv_write_cached_reg()
ata: fix return value check in ahci_seattle_get_port_info()
Note that `&acdev->host->lock' and `qc->ap->lock' denote the same lock, and it's
particularly confusing to spin_lock on the former but spin_unlock on the latter.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Fix the signed issue in mv_write_cached_reg() where the laddr
is assigned from a (long)addr instead of (unsigned long)addr.
Fixes the following warnings:
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sysfs file for the libata error handling has multiple issues
in the way it prints time stamps:
* it prints a 9-digit nanosecond value using a %06lu format string,
which drops some leading zeroes
* it converts a 64-bit jiffes value to a timespec using
jiffies_to_timespec(), which takes a 'long' argument, so the
result is wrong after a jiffies overflow (49 days).
* we try to avoid using timespec because that generally overflows
in 2038, although this particular usage is ok.
This replaces the jiffies_to_timespec call with an open-coded
implementation that gets it right.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
In case of error, the function devm_kzalloc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.
It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.
Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.
Fixes: 50824d6c56 ("[SCSI] libsas: async ata-eh")
Cc: stable@vger.kernel.org
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This patch converts the drivers and cgroup to use the
op_is_write helper. This should just cover the simple
cases. I did dm, md and bcache in their own patches
because they were more involved.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove extraneous space on if statement and on the following line,
trivial fix, no functional change
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata sata_dwc_460ex updates from Tejun Heo:
"Patches to bring sata_dwc_460ex up to snuff.
It was a separate pull request because it depends on dmaengine dw
platform changes which are now in mainline"
* 'for-4.7-dw' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (24 commits)
ata: dwc: add DMADEVICES dependency
powerpc/4xx: Device tree update for the 460ex DWC SATA
ata: sata_dwc_460ex: make debug messages neat
ata: sata_dwc_460ex: supply physical address of FIFO to DMA
ata: sata_dwc_460ex: use devm_ioremap
ata: sata_dwc_460ex: tidy up sata_dwc_clear_dmacr()
ata: sata_dwc_460ex: use readl/writel_relaxed()
ata: sata_dwc_460ex: switch to new dmaengine_terminate_* API
ata: sata_dwc_460ex: add __iomem to register base pointer
ata: sata_dwc_460ex: get rid of incorrect cast
ata: sata_dwc_460ex: get rid of some pointless casts
ata: sata_dwc_460ex: remove empty libata callback
ata: sata_dwc_460ex: correct HOSTDEV{P}_FROM_*() macros
ata: sata_dwc_460ex: get rid of global data
ata: sata_dwc_460ex: add phy support
ata: sata_dwc_460ex: use "dmas" DT property to find dma channel
ata: sata_dwc_460ex: don't call ata_sff_qc_issue() on DMA commands
ata: sata_dwc_460ex: skip dma setup for non-dma commands
ata: sata_dwc_460ex: select only core part of DMA driver
ata: sata_dwc_460ex: DMA is always a flow controller
...
Pull libata ZAC support from Tejun Heo:
"This contains Zone ATA Command support for Shingled Magnetic Recording
devices.
In addition to sending the new commands down to the device, as ZAC
commands depend on getting a lot of responses from the device, piping
up responses is beefed up too. However, it doesn't involve changes to
libata core mechanism or its interaction with upper layers, so I'm not
expecting too many fallouts.
Kudos to Hannes for driving SMR support"
* 'for-4.7-zac' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (28 commits)
libata: support host-aware and host-managed ZAC devices
libata: support device-managed ZAC devices
libata: NCQ encapsulation for ZAC MANAGEMENT OUT
libata: Implement ZBC OUT translation
libata: implement ZBC IN translation
libata: fixup ZAC device disabling
libata-scsi: Generate sense code for disabled devices
libata-trace: decode subcommands
libata: Check log page directory before accessing pages
libata: Add command definitions for NCQ Encapsulation for READ LOG DMA EXT
libata: Separate out ata_dev_config_ncq_send_recv()
libata/libsas: Define ATA_CMD_NCQ_NON_DATA
libsas: enable FPDMA SEND/RECEIVE
libata: do not attempt to retrieve sense code twice
libata-scsi: Set information sense field for invalid parameter
libata-scsi: set bit pointer for sense code information
libata-scsi: Set field pointer in sense code
scsi: add scsi_set_sense_field_pointer()
libata: Implement control mode page to select sense format
libata-scsi: generate correct ATA pass-through sense
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
This patch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas) there's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJXO8W0AAoJEDeqqVYsXL0MW24H/jGWwfjsDUiSsLwbLca6DWu8
ZCWZ7rSZ27CApwGPgZGpLvUg+vpW8Ykm2zdeBnlZ6ScXS+dT3uo/PHsnemsTextj
6glQNIOFY0Ja2GwkkN00M6IZQhTJ628cqJKIEJxC68lIw16wiOwjZaK68GMrusDO
Sl062rkuLR6Jb2T+YoT/sD8jQfWlSj2V9e9rqJoS/rIbS6B+hUipuybz2yQ2yK2u
XFc30yal9oVz1fHEoh2O8aqckW3/iskukVXVuZ0MQzT/lV/bm9I6AnWVHw7d0Yhp
ZELjXpjx5M2Z/d8k0Wvx1e25oL/ERwa96yLnTvRcqyF5Yt1EgAhT+jKvo4pnGr8=
=L6y/
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"First round of SCSI updates for the 4.6+ merge window.
This batch includes the usual quota of driver updates (bnx2fc, mp3sas,
hpsa, ncr5380, lpfc, hisi_sas, snic, aacraid, megaraid_sas). There's
also a multiqueue update for scsi_debug, assorted bug fixes and a few
other minor updates (refactor of scsi_sg_pools into generic code, alua
and VPD updates, and struct timeval conversions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (138 commits)
mpt3sas: Used "synchronize_irq()"API to synchronize timed-out IO & TMs
mpt3sas: Set maximum transfer length per IO to 4MB for VDs
mpt3sas: Updating mpt3sas driver version to 13.100.00.00
mpt3sas: Fix initial Reference tag field for 4K PI drives.
mpt3sas: Handle active cable exception event
mpt3sas: Update MPI header to 2.00.42
Revert "lpfc: Delete unnecessary checks before the function call mempool_destroy"
eata_pio: missing break statement
hpsa: Fix type ZBC conditional checks
scsi_lib: Decode T10 vendor IDs
scsi_dh_alua: do not fail for unknown VPD identification
scsi_debug: use locally assigned naa
scsi_debug: uuid for lu name
scsi_debug: vpd and mode page work
scsi_debug: add multiple queue support
bfa: fix bfa_fcb_itnim_alloc() error handling
megaraid_sas: Downgrade two success messages to info
cxlflash: Fix to resolve dead-lock during EEH recovery
scsi_debug: rework resp_report_luns
scsi_debug: use pdt constants
...
The dwc_460ex SATA driver has become available on non-powerpc architectures
and may cause randconfig build errors when CONFIG_DMADEVICES is not set
and SATA_DWC_OLD_DMA is enabled:
warning: (SATA_DWC_OLD_DMA) selects DW_DMAC_CORE which has unmet direct dependencies (DMADEVICES)
ERROR: "dw_dma_probe" [drivers/ata/sata_dwc_460ex.ko] undefined!
ERROR: "dw_dma_remove" [drivers/ata/sata_dwc_460ex.ko] undefined!
This adds an explcit Kconfig dependency to CONFIG_SATA_DWC so we
cannot run into broken configurations. While it would also be
possible to build the driver with both CONFIG_DMADEVICES
and SATA_DWC_OLD_DMA disabled, that case is not useful because
there is no fallback to PIO mode when the DMA engine is not
usable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 50b433753d ("ata: sata_dwc_460ex: use "dmas" DT property to find dma channel")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a duplication in the debug messages when accessing SCR registers.
Remove duplication to make the messages neat.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
DMA operates with physical addresses which is not exactly the same as ioremap()
returns.
Introduce variable to keep physical address of the SATA FIFO register and
supply it when prepare DMA channel.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This simplifies error handling and cleanup by using devm to manage
IO mappings.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This consolidates the reads from each of the if/else branches
to one place making the code a lot nicer to look at.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Rename the register access macros and use standard _relaxed()
ops instead of __raw variants with explicit byte swapping.
The original driver used the ppc-specific in/out_le32(). When it
was adapted to other systems, these were added to the driver
under ifdefs. However, those names are not defined as macros on
ppc, so it ended up replacing them there as well with altered
semantics. This patch restores the original semantics on ppc and
makes the accesses no less strict on other systems.
Also fixes too many sparse warnings to count.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pointer to the mmio register base is missing the __iomem
annotation. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The (void *__iomem) cast is wrong. Change the target type of the
"base" pointer to void __iomem instead and drop the cast.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Casting a pointer to unsigned long only to immediately cast it back
to a pointer makes no sense. Fix this.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata_dwc_qc_prep() does nothing. Use the default ata_noop_qc_prep
instead.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here we refactor HOSTDEV{P}_FROM_*() macros to fit one line and fix the
definition of HSDEV_FROM_HSDEVP() where wrong name of the parameter waas used.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This moves all global data into the driver private struct, thus
permitting multiple devices of this type to be used.
The core_scr_read/write() functions are replaced with equivalent
calls to the existing sata_dwc_scr_read/write().
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds support for powering on an optional PHY when activating the
device.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently this driver only works with a DesignWare DMA engine which it
registers manually using the second "reg" address range and interrupt
number from the DT node.
This patch makes the driver instead use the "dmas" property if present,
otherwise optionally falling back on the old way so existing device
trees can continue to work.
With this change, there is no longer any reason to depend on the 460EX
machine type so drop that from Kconfig.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_sff_qc_issue() can't handle DMA commands and thus we have to avoid it for
them. Do call ata_bmdma_qc_issue() instead for this case. Note that the former
one distinguishes PIO and DMA mode and behaves accordingly.
Suggested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Calling dmaengine_prep_slave_sg() for non-dma ATA commands is
unnecessary at best and could be harmful if the dma driver reacts
badly to this. It also causes this driver to print a bogus error
message in these cases.
This patch changes sata_dwc_qc_issue() to only do the dma setup
for dma commands and also reports an error to libata if if fails.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no need to have a platform driver compiled since the DMA driver is
used as a library.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In the original code the DMA is always a flow controller. Set this accordingly
in updated code.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The burst size as defined by DMAengine API is in items of address width. Derive
burst size from AHB_DMA_BRST_DFLT (64 bytes) by dividing it to
DMA_SLAVE_BUSWIDTH_4_BYTES (4 bytes) that gives us 16 items.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The original code states:
Make sure a LLI block is not created that will span 8K max FIS
boundary. If the block spans such a FIS boundary, there is a chance
that a DMA burst will cross that boundary -- this results in an error
in the host controller.
Since we have switched to generic DMAengine API we satisfy above by setting
dma_boundary value to 0x1fff.
Suggested-by: Mans Rullgard <mans@mansr.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes Machine Check "Data Write PLB Error" which happens
when libata-sff's ata_sff_dev_select is trying to write into the
device_addr in order to select a drive. However, SATA has no master
or slave devices like the old ATA Bus, therefore selecting a
different drive is kind of pointless.
Data Write PLB Error
Oops: Machine check, sig: 7 [#1]
PowerPC 44x Platform
Modules linked in:
CPU: 0 PID: 508 Comm: scsi_eh_0 Not tainted 4.6.0-rc3-next-20160412+ #10
[...]
NIP [c027e820] ata_sff_dev_select+0x3c/0x44
LR [c027e810] ata_sff_dev_select+0x2c/0x44
Call Trace:
[cec31cd0] [c027da00] ata_sff_postreset+0x40/0xb4 (unreliable)
[cec31ce0] [c027a03c] ata_eh_reset+0x5cc/0x928
[cec31d60] [c027a840] ata_eh_recover+0x330/0x10bc
[cec31df0] [c027bae0] ata_do_eh+0x4c/0xa4
[...]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bartosz Golaszewski