When emulating an instruction that reads the destination memory operand (i.e.,
instructions without the Mov flag in the emulator), the operand is first read.
If a page-fault is detected in this phase, the error-code which would be
delivered to the VM does not indicate that the access that caused the exception
is a write one. This does not conform with real hardware, and may cause the VM
to enter the page-fault handler twice for no reason (once for read, once for
write).
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When access to descriptor in LDT/GDT wraparound outside long-mode, the address
of the descriptor should be truncated to 32-bit. Citing Intel SDM 2.1.1.1
"Global and Local Descriptor Tables in IA-32e Mode": "GDTR and LDTR registers
are expanded to 64-bits wide in both IA-32e sub-modes (64-bit mode and
compatibility mode)."
So in other cases, we need to truncate. Creating new function to return a
pointer to descriptor table to avoid too much code duplication.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Wrap 64-bit check with #ifdef CONFIG_X86_64, to avoid a "right shift count
>= width of type" warning and consequent undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When segment is loaded, the segment access bit is set unconditionally. In
fact, it should be set conditionally, based on whether the segment had the
accessed bit set before. In addition, it can improve performance.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to Intel SDM: "If the ESP register is used as a base register for
addressing a destination operand in memory, the POP instruction computes the
effective address of the operand after it increments the ESP register."
The current emulation does not behave so. The fix required to waste another
of the precious instruction flags and to check the flag in decode_modrm.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, if em_call_far fails it returns success instead of the resulting
error-code. Fix it.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM emulator does not emulate JMP and CALL that target a call gate or a
task gate. This patch does not try to implement these scenario as they are
presumably rare; yet it returns X86EMUL_UNHANDLEABLE error in such cases
instead of generating an exception.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the operand size of fnstcw and fnstsw is updated during the execution,
the emulation may cause spurious exceptions as it reads the memory beforehand.
Marking these instructions as Mov (since the previous value is ignored) and
DstMem16 to simplify the setting of operand size.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Although pop sreg updates RSP according to the operand size, only 2 bytes are
read. The current behavior may result in incorrect #GP or #PF exceptions.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove FIXME comments about needing fault addresses to be returned. These
are propaagated from walk_addr_generic to gva_to_gpa and from there to
ops->read_std and ops->write_std.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- spring cleaning: removed support for IA64, and for hardware-assisted
virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken because
the (non-KVM) XSAVES patches inadvertently changed the KVM userspace
ABI whenever XSAVES was enabled; hence, this part is going to stable.
Guest support is just a matter of exposing the feature and CPUID leaves
support.
Right now KVM is broken for PPC BookE in your tree (doesn't compile).
I'll reply to the pull request with a patch, please apply it either
before the pull request or in the merge commit, in order to preserve
bisectability somewhat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUkpg+AAoJEL/70l94x66DUmoH/jzXYkptSW9NGgm79KqxGJlD
lzLnLBkitVvx++Mz5YBhdJEhKKLUlCtifFT1zPJQ/pthQhIRSaaAwZyNGgUs5w5x
yMGKHiPQFyZRbmQtZhCInW0BftJoYHHciO3nUfHCZnp34My9MP2D55W7/z+fYFfQ
DuqBSE9ThyZJtZ4zh8NRA9fCOeuqwVYRyoBs820Wbsh4cpIBoIK63Dg7k+CLE+ZV
MZa/mRL6bAfsn9W5bnOUAgHJ3SPznnWbO3/g0aV+roL/5pffblprJx9lKNR08xUM
6hDFLop2gDehDJesDkY/o8Ckp1hEouvfsVpSShry4vcgtn0hgh2O5/6Orbmj6vE=
=Zwq1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM update from Paolo Bonzini:
"3.19 changes for KVM:
- spring cleaning: removed support for IA64, and for hardware-
assisted virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken
because the (non-KVM) XSAVES patches inadvertently changed the KVM
userspace ABI whenever XSAVES was enabled; hence, this part is
going to stable. Guest support is just a matter of exposing the
feature and CPUID leaves support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (179 commits)
KVM: move APIC types to arch/x86/
KVM: PPC: Book3S: Enable in-kernel XICS emulation by default
KVM: PPC: Book3S HV: Improve H_CONFER implementation
KVM: PPC: Book3S HV: Fix endianness of instruction obtained from HEIR register
KVM: PPC: Book3S HV: Remove code for PPC970 processors
KVM: PPC: Book3S HV: Tracepoints for KVM HV guest interactions
KVM: PPC: Book3S HV: Simplify locking around stolen time calculations
arch: powerpc: kvm: book3s_paired_singles.c: Remove unused function
arch: powerpc: kvm: book3s_pr.c: Remove unused function
arch: powerpc: kvm: book3s.c: Remove some unused functions
arch: powerpc: kvm: book3s_32_mmu.c: Remove unused function
KVM: PPC: Book3S HV: Check wait conditions before sleeping in kvmppc_vcore_blocked
KVM: PPC: Book3S HV: ptes are big endian
KVM: PPC: Book3S HV: Fix inaccuracies in ICP emulation for H_IPI
KVM: PPC: Book3S HV: Fix KSM memory corruption
KVM: PPC: Book3S HV: Fix an issue where guest is paused on receiving HMI
KVM: PPC: Book3S HV: Fix computation of tlbie operand
KVM: PPC: Book3S HV: Add missing HPTE unlock
KVM: PPC: BookE: Improve irq inject tracepoint
arm/arm64: KVM: Require in-kernel vgic for the arch timers
...
commit d50eaa1803 ("KVM: x86: Perform limit checks when assigning EIP")
mistakenly used zero as cpl on em_ret_far. Use the actual one.
Fixes: d50eaa1803
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel SDM table 6-2 ("Priority Among Simultaneous Exceptions and Interrupts")
shows that faults from decoding the next instruction got higher priority than
general protection. Moving the protected-mode check before the CPL check to
avoid wrong exception on vm86 mode.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The pushf instruction does not push eflags.VM, so emulation should not do so as
well. Although eflags.RF should not be pushed as well, it is already cleared
by the time pushf is executed.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The macro GP already sets the flag Prefix. Remove the redundant flag for
0f_38_f0 and 0f_38_f1 opcodes.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Certain x86 instructions that use modrm operands only allow memory operand
(i.e., mod012), and cause a #UD exception otherwise. KVM ignores this fact.
Currently, the instructions that are such and are emulated by KVM are MOVBE,
MOVNTPS, MOVNTPD and MOVNTI. MOVBE is the most blunt example, since it may be
emulated by the host regardless of MMIO.
The fix introduces a new group for handling such instructions, marking mod3 as
illegal instruction.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove FIXME comments about needing fault addresses to be returned. These
are propaagated from walk_addr_generic to gva_to_gpa and from there to
ops->read_std and ops->write_std.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The check on the higher limit of the segment, and the check on the
maximum accessible size, is the same for both expand-up and
expand-down segments. Only the computation of "lim" varies.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
register_address has been a duplicate of address_mask ever since the
ancestor of __linearize was born in 90de84f50b (KVM: x86 emulator:
preserve an operand's segment identity, 2010-11-17).
However, we can put it to a better use by including the call to reg_read
in register_address. Similarly, the call to reg_rmw can be moved to
register_address_increment.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In __linearize there is check of the condition whether to check if masking of
the linear address is needed. It occurs immediately after switch that
evaluates the same condition. Merge them.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When SS is used using a non-canonical address, an #SS exception is generated on
real hardware. KVM emulator causes a #GP instead. Fix it to behave as real x86
CPU.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If branch (e.g., jmp, ret) causes limit violations, since the target IP >
limit, the #GP exception occurs before the branch. In other words, the RIP
pushed on the stack should be that of the branch and not that of the target.
To do so, we can call __linearize, with new EIP, which also saves us the code
which performs the canonical address checks. On the case of assigning an EIP >=
2^32 (when switching cs.l), we also safe, as __linearize will check the new EIP
does not exceed the limit and would trigger #GP(0) otherwise.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When segment is accessed, real hardware does not perform any privilege level
checks. In contrast, KVM emulator does. This causes some discrepencies from
real hardware. For instance, reading from readable code segment may fail due to
incorrect segment checks. In addition, it introduces unnecassary overhead.
To reference Intel SDM 5.5 ("Privilege Levels"): "Privilege levels are checked
when the segment selector of a segment descriptor is loaded into a segment
register." The SDM never mentions privilege level checks during memory access,
except for loading far pointers in section 5.10 ("Pointer Validation"). Those
are actually segment selector loads and are emulated in the similarily (i.e.,
regardless to __linearize checks).
This behavior was also checked using sysexit. A data-segment whose DPL=0 was
loaded, and after sysexit (CPL=3) it is still accessible.
Therefore, all the privilege level checks in __linearize are removed.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When performing segmented-read/write in the emulator for stack operations, it
ignores the stack size, and uses the ad_bytes as indication for the pointer
size. As a result, a wrong address may be accessed.
To fix this behavior, we can remove the masking of address in __linearize and
perform it beforehand. It is already done for the operands (so currently it is
inefficiently done twice). It is missing in two cases:
1. When using rip_relative
2. On fetch_bit_operand that changes the address.
This patch masks the address on these two occassions, and removes the masking
from __linearize.
Note that it does not mask EIP during fetch. In protected/legacy mode code
fetch when RIP >= 2^32 should result in #GP and not wrap-around. Since we make
limit checks within __linearize, this is the expected behavior.
Partial revert of commit 518547b32a (KVM: x86: Emulator does not
calculate address correctly, 2014-09-30).
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 10e38fc7cab6 ("KVM: x86: Emulator flag for instruction that only support
16-bit addresses in real mode") introduced NoBigReal for instructions such as
MONITOR. Apparetnly, the Intel SDM description that led to this patch is
misleading. Since no instruction is using NoBigReal, it is safe to remove it,
we fully understand what the SDM means.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 3b32004a66 ("KVM: x86: movnti minimum op size of 32-bit is not kept")
did not fully fix the minimum operand size of MONTI emulation. Still, MOVNTI
may be mistakenly performed using 16-bit opsize.
This patch add No16 flag to mark an instruction does not support 16-bits
operand size.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that KVM injects #UD on "unhandlable" error, it makes better sense to
return such error on sysenter instead of directly injecting #UD to the guest.
This allows to track more easily the unhandlable cases the emulator does not
support.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 7fe864dc94 (KVM: x86: Mark VEX-prefix instructions emulation as
unimplemented, 2014-06-02) marked VEX instructions as such in protected
mode. VEX-prefix instructions are not supported relevant on real-mode
and VM86, but should cause #UD instead of being decoded as LES/LDS.
Fix this behaviour to be consistent with real hardware.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Check for mod == 3, rather than 2 or 3. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Task-switch emulation checks the privilege level prior to performing the
task-switch. This check is incorrect in the case of task-gates, in which the
tss.dpl is ignored, and can cause superfluous exceptions. Moreover this check
is unnecassary, since the CPU checks the privilege levels prior to exiting.
Intel SDM 25.4.2 says "If CALL or JMP accesses a TSS descriptor directly
outside IA-32e mode, privilege levels are checked on the TSS descriptor" prior
to exiting. AMD 15.14.1 says "The intercept is checked before the task switch
takes place but after the incoming TSS and task gate (if one was involved) have
been checked for correctness."
This patch removes the CPL checks for CALL and JMP.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When emulating LTR/LDTR/LGDT/LIDT, #GP should be injected if the base is
non-canonical. Otherwise, VM-entry will fail.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
LGDT and LIDT emulation logic is almost identical. Merge the logic into a
single point to avoid redundancy. This will be used by the next patch that
will ensure the bases of the loaded GDTR and IDTR are canonical.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Although Intel SDM mentions bit 63 is reserved, MOV to CR3 can have bit 63 set.
As Intel SDM states in section 4.10.4 "Invalidation of TLBs and
Paging-Structure Caches": " MOV to CR3. ... If CR4.PCIDE = 1 and bit 63 of the
instruction’s source operand is 0 ..."
In other words, bit 63 is not reserved. KVM emulator currently consider bit 63
as reserved. Fix it.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to Intel SDM push of segment selectors is done in the following
manner: "if the operand size is 32-bits, either a zero-extended value is pushed
on the stack or the segment selector is written on the stack using a 16-bit
move. For the last case, all recent Core and Atom processors perform a 16-bit
move, leaving the upper portion of the stack location unmodified."
This patch modifies the behavior to match the core behavior.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CMPS and SCAS instructions are evaluated in the wrong order. For reference (of
CMPS), see http://www.fermimn.gov.it/linux/quarta/x86/cmps.htm : "Note that the
direction of subtraction for CMPS is [SI] - [DI] or [ESI] - [EDI]. The left
operand (SI or ESI) is the source and the right operand (DI or EDI) is the
destination. This is the reverse of the usual Intel convention in which the
left operand is the destination and the right operand is the source."
Introducing em_cmp_r for this matter that performs comparison in reverse order
using fastop infrastructure to avoid a wrapper function.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SYSCALL emulation currently clears in 64-bit mode eflags according to
MSR_SYSCALL_MASK. However, on bare-metal eflags[1] which is fixed to one
cannot be cleared, even if MSR_SYSCALL_MASK masks the bit. This wrong behavior
may result in failed VM-entry, as VT disallows entry with eflags[1] cleared.
This patch sets the bit after masking eflags on syscall.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In x86, you can only MOV-sreg to memory with either 16-bits or 64-bits size.
In contrast, KVM may write to 32-bits memory on MOV-sreg. This patch fixes KVM
behavior, and sets the destination operand size to two, if the destination is
memory.
When destination is registers, and the operand size is 32-bits, the high
16-bits in modern CPUs is filled with zero. This is handled correctly.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In one occassion, decode_modrm uses the rm field after it is extended with
REX.B to determine the addressing mode. Doing so causes it not to read the
offset for rip-relative addressing with REX.B=1.
This patch moves the fetch where we already mask REX.B away instead.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The emulator could reuse an op->type from a previous instruction for some
immediate values. If it mistakenly considers the operands as memory
operands, it will performs a memory read and overwrite op->val.
Consider for instance the ROR instruction - src2 (the number of times)
would be read from memory instead of being used as immediate.
Mark every immediate operand as such to avoid this problem.
Cc: stable@vger.kernel.org
Fixes: c44b4c6ab8
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When read access is performed using a readable code segment, the "conforming"
and "non-conforming" checks should not be done. As a result, read using
non-conforming readable code segment fails.
This is according to Intel SDM 5.6.1 ("Accessing Data in Code Segments").
The fix is not to perform the "non-conforming" checks if the access is not a
fetch; the relevant checks are already done when loading the segment.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In long-mode, when the address size is 4 bytes, the linear address is not
truncated as the emulator mistakenly does. Instead, the offset within the
segment (the ea field) should be truncated according to the address size.
As Intel SDM says: "In 64-bit mode, the effective address components are added
and the effective address is truncated ... before adding the full 64-bit
segment base."
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the operand size is not 64-bit, then the sysexit instruction should assign
ECX to RSP and EDX to RIP. The current code assigns the full 64-bits.
Fix it by masking.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In 64-bit, stack operations default to 64-bits, but can be overriden (to
16-bit) using opsize override prefix. In contrast, near-branches are always
64-bit. This patch distinguish between the different behaviors.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Breaking grp45 to the relevant functions to speed up the emulation and simplify
the code. In addition, it is necassary the next patch will distinguish between
far and near branches according to the flags.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the current canonical address check with the new function which is
identical.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit d1442d85cc ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit d1442d85cc ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Emulation of code that is 14 bytes to the segment limit or closer
(e.g. RIP = 0xFFFFFFF2 after reset) is broken because we try to read as
many as 15 bytes from the beginning of the instruction, and __linearize
fails when the passed (address, size) pair reaches out of the segment.
To fix this, let __linearize return the maximum accessible size (clamped
to 2^32-1) for usage in __do_insn_fetch_bytes, and avoid the limit check
by passing zero for the desired size.
For expand-down segments, __linearize is performing a redundant check.
(u32)(addr.ea + size - 1) <= lim can only happen if addr.ea is close
to 4GB; in this case, addr.ea + size - 1 will also fail the check against
the upper bound of the segment (which is provided by the D/B bit).
After eliminating the redundant check, it is simple to compute
the *max_size for expand-down segments too.
Now that the limit check is done in __do_insn_fetch_bytes, we want
to inject a general protection fault there if size < op_size (like
__linearize would have done), instead of just aborting.
This fixes booting Tiano Core from emulated flash with EPT disabled.
Cc: stable@vger.kernel.org
Fixes: 719d5a9b24
Reported-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error code for #GP and #SS is zero when the segment is used to
access an operand or an instruction. It is only non-zero when
a segment register is being loaded; for limit checks this means
cases such as:
* for #GP, when RIP is beyond the limit on a far call (before the first
instruction is executed). We do not implement this check, but it
would be in em_jmp_far/em_call_far.
* for #SS, if the new stack overflows during an inter-privilege-level
call to a non-conforming code segment. We do not implement stack
switching at all.
So use an error code of zero.
Reviewed-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The decode phase of the x86 emulator assumes that every instruction with the
ModRM flag, and which can be used with RIP-relative addressing, has either
SrcMem or DstMem. This is not the case for several instructions - prefetch,
hint-nop and clflush.
Adding SrcMem|NoAccess for prefetch and hint-nop and SrcMem for clflush.
This fixes CVE-2014-8480.
Fixes: 41061cdb98
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nadav Amit