The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.
For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.
Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the tx_packets and
tx_bytes fields of struct net_device_stats when sending an error
message frame because no actual payload will be transmitted on the
wire.
N.B. Sending error message frames is a very specific feature which, at
the moment, is only supported by the Kvaser Hydra hardware. Please
refer to [1] for more details on the topic.
[1] https://lore.kernel.org/linux-can/CAMZ6RqK0rTNg3u3mBpZOoY51jLZ-et-J01tY6-+mWsM4meVw-A@mail.gmail.com/t/#u
Link: https://lore.kernel.org/all/20211207121531.42941-3-mailhol.vincent@wanadoo.fr
Co-developed-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the rx_packets and
rx_bytes fields of struct net_device_stats because no actual payload
were transmitted on the wire.
This patch fixes all the CAN drivers.
Link: https://lore.kernel.org/all/20211207121531.42941-2-mailhol.vincent@wanadoo.fr
CC: Marc Kleine-Budde <mkl@pengutronix.de>
CC: Nicolas Ferre <nicolas.ferre@microchip.com>
CC: Alexandre Belloni <alexandre.belloni@bootlin.com>
CC: Ludovic Desroches <ludovic.desroches@microchip.com>
CC: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
CC: Maxime Ripard <mripard@kernel.org>
CC: Chen-Yu Tsai <wens@csie.org>
CC: Jernej Skrabec <jernej.skrabec@gmail.com>
CC: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
CC: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The field dev_port of struct net_device indicates the port number of a
network device [1]. This patch populates this field.
This field can be helpful to distinguish between the two network
interfaces of a dual channel device (i.e. ES581.4 or ES582.1). Indeed,
at the moment, all the network interfaces of a same device share the
same static udev attributes c.f. output of:
| udevadm info --attribute-walk /sys/class/net/canX
The dev_port attribute can then be used to write some udev rules to,
for example, assign a permanent name to each network interface based
on the serial/dev_port pair (which is convenient when you have a test
bench with several CAN devices connected simultaneously and wish to
keep consistent interface names upon reboot).
[1] https://www.kernel.org/doc/Documentation/ABI/testing/sysfs-class-net
Link: https://lore.kernel.org/all/20211026180553.1953189-1-mailhol.vincent@wanadoo.fr
Suggested-by: Lukas Magel <lukas.magel@escrypt.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue when
using hierarchical interrupt domains using "interrupts" property in
the node as this bypasses the hierarchical setup and messes up the irq
chaining.
In preparation for removal of static setup of IRQ resource from DT
core code use platform_get_irq().
Link: https://lore.kernel.org/all/20211221194508.11737-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
GPIO library does copy the of_node from the parent device of the GPIO
chip, there is no need to repeat this in the individual drivers.
Remove assignment here.
For the details one may look into the of_gpio_dev_init()
implementation.
Link: https://lore.kernel.org/all/20211202205855.76946-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Depending on BIOS configuration IOSM driver exchanges
protocol required for putting device into D3L2 or D3L1.2.
ipc_pcie_suspend_s2idle() is implemented to put device to D3L1.2.
This patch forces PCI core know this device should stay at D0.
- pci_save_state()is expensive since it does a lot of slow PCI
config reads.
The reported issue is not observed on x86 platform. The supurios
wake on AMD platform needs to be futher debugged with orignal patch
submitter [1]. Also the impact of adding pci_save_state() needs to be
assessed by testing it on other platforms.
This reverts commit f4dd5174e273("net: wwan: iosm: Keep device
at D0 for s2idle case").
[1] https://lore.kernel.org/all/20211224081914.345292-2-kai.heng.feng@canonical.com/
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Link: https://lore.kernel.org/r/20220104150213.1894-1-m.chetan.kumar@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Return value from efx_mcdi_rpc() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent bpf-next merge brought in header changes which uncovered
includes missing in net-next which were not present in bpf-next.
Build problems happen only on less-popular arches like hppa,
sparc, alpha etc.
I could repro the build problem with ice but not the mlx5 problem
Abdul was reporting. mlx5 does look like it should include filter.h,
anyway.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Fixes: e63a023489 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next")
Link: https://lore.kernel.org/all/7c03768d-d948-c935-a7ab-b1f963ac7eed@linux.vnet.ibm.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for scatter gather DMA. DMA in PMAC splits
the packet into several buffers when the MTU on the CPU port is
less than the MTU of the switch. The first buffer starts at an
offset of NET_IP_ALIGN. In subsequent buffers, dma ignores the
offset. Thanks to this patch, the user can still connect to the
device in such a situation. For normal configurations, the patch
has no effect on performance.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for external timestamp and periodic signal output.
TJA1103 have one periodic signal and one external time stamp signal that
can be multiplexed on all 11 gpio pins.
The periodic signal can be only enabled or disabled. Have no start time
and if is enabled will be generated with a period of one second in sync
with the LTC seconds counter. The phase change is possible only with a
half of a second.
The external timestamp signal has no interrupt and no valid bit and
that's why the timestamps are handled by polling in .do_aux_work.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get originating device from tuple offload metadata match ingress_ifindex,
and set flow_source hint to either LOCAL for vf/sf reps, UPLINK for
uplink/wire/tunnel devices/bond, or ANY (as before this patch)
for all others.
This allows lower layer (software steering or firmware) to insert the tuple
rule only in one table (either rx or tx) instead of two (rx and tx).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'high_dma' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including a now
useless parameter to vxge_device_register().
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'dma_flag' can only be 'true' after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly, including the now
useless 'high_dma_flag' field in 'struct s2io_nic'.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sorry for being rude but new vendors/drivers are supposed to be disabled
by default, otherwise we will have to manually keep track of all vendors
we are not interested in building.
Fixes: 2f207cbf0d ("net: vertexcom: Add MSE102x SPI support")
CC: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcs-lynx.c used lynx_pcs and lynx as a variable name within the same file.
This standardizes all internal variables to just "lynx"
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple variable update from "pcs" to "mdio_device" for the mdio device
will make things a little cleaner.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple rename of a variable to make things more logical.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove references to lynx_pcs structures so drivers like the Felix DSA
can reference alternate PCS drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.
Some reasons why this API should be removed have been given by Julia
Lawall in [2].
A coccinelle script has been used to perform the needed transformation
Only relevant parts are given below.
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
[1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
Now that qed_set_coherency_mask() is mostly a single call to
dma_set_mask_and_coherent(), fold it in its only caller.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask() with a 64-bit mask will never
fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
Moreover, as stated in [1], dma_set_mask_and_coherent() with a 64-bit mask
will never fail if dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
That said, 'pci_using_dac' can only be 1 after a successful
dma_set_mask_and_coherent().
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_set_mask_and_coherent() instead of unrolling it with some
dma_set_mask()+dma_set_coherent_mask().
This simplifies code and removes some dead code (dma_set_coherent_mask()
can not fail after a successful dma_set_mask())
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 Software steering, New features and optimizations
This patch series brings various SW steering features, optimizations and
debug-ability focused improvements.
1) Expose debugfs for dumping the SW steering resources
2) Removing unused fields
3) support for matching on new fields
4) steering optimization for RX/TX-only rules
5) Make Software steering the default steering mechanism when
available, applies only to Switchdev mode FDB
From Yevgeny Kliteynik and Muhammad Sammar:
- Patch 1 fixes an error flow in creating matchers
- Patch 2 fix lower case macro prefix "mlx5_" to "MLX5_"
- Patch 3 removes unused struct member in mlx5dr_matcher
- Patch 4 renames list field in matcher struct to list_node to reflect the
fact that is field is for list node that is stored on another struct's lists
- Patch 5 adds checking for valid Flex parser ID value
- Patch 6 adds the missing reserved fields to dr_match_param and aligns it to
the format that is defined by HW spec
- Patch 7 adds support for dumping SW steering (SMFS) resources using debugfs
in CSV format: domain and its tables, matchers and rules
- Patch 8 adds support for a new destination type - UPLINK
- Patch 9 adds WARN_ON_ONCE on refcount checks in SW steering object destructors
- Patches 10, 11, 12 add misc5 flow table match parameters and add support for
matching on tunnel headers 0 and 1
- Patch 13 adds support for matching on geneve_tlv_option_0_exist field
- Patch 14 implements performance optimization for for empty or RX/TX-only
matchers by splitting RX and TX matchers handling: matcher connection in the
matchers chain is split into two separate lists (RX only and TX only), which
solves a usecase of many RX or TX only rules that create a long chain of
RX/TX-only paths w/o the actual rules
- Patch 15 ignores modify TTL if device doesn't support it instead of
adding and unsupported action
- Patch 16 sets SMFS as a default steering mode
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmHOvKsACgkQSD+KveBX
+j4CpQf8Cc3NkWhGVYYhRBlntdpyVTDpoVhw6RDXVwboIRZ3GcMm81SxgwKrDuUx
Yhup4K1CNKt44D1RRhX4ElSemfo/afxfGIcq7S87vciUOaebWTIZgRyNvuYr/buI
v9LIM7zTb1aXL7m3KQHOGc7cucVRvsNjteTxvp/DR0bPFEuzAr5tw9Y5qop9pBbM
cfgdmXKUoRxA039mqZ2Fl7y+z51zRkfsCza7lEHcGgpvwOLubFEaghj7YTIT6h1m
+We8w3/+B0mqS0HpByIxmyf/EQBG5Hl7FTbFj1Somn7EFEP4E+LaFzg8nGsUHEeI
f5027uM7XGlThAUrgdaOMcwBfIuOww==
=BE8m
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-12-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 Software steering, New features and optimizations
This patch series brings various SW steering features, optimizations and
debug-ability focused improvements.
1) Expose debugfs for dumping the SW steering resources
2) Removing unused fields
3) support for matching on new fields
4) steering optimization for RX/TX-only rules
5) Make Software steering the default steering mechanism when
available, applies only to Switchdev mode FDB
From Yevgeny Kliteynik and Muhammad Sammar:
- Patch 1 fixes an error flow in creating matchers
- Patch 2 fix lower case macro prefix "mlx5_" to "MLX5_"
- Patch 3 removes unused struct member in mlx5dr_matcher
- Patch 4 renames list field in matcher struct to list_node to reflect the
fact that is field is for list node that is stored on another struct's lists
- Patch 5 adds checking for valid Flex parser ID value
- Patch 6 adds the missing reserved fields to dr_match_param and aligns it to
the format that is defined by HW spec
- Patch 7 adds support for dumping SW steering (SMFS) resources using debugfs
in CSV format: domain and its tables, matchers and rules
- Patch 8 adds support for a new destination type - UPLINK
- Patch 9 adds WARN_ON_ONCE on refcount checks in SW steering object destructors
- Patches 10, 11, 12 add misc5 flow table match parameters and add support for
matching on tunnel headers 0 and 1
- Patch 13 adds support for matching on geneve_tlv_option_0_exist field
- Patch 14 implements performance optimization for for empty or RX/TX-only
matchers by splitting RX and TX matchers handling: matcher connection in the
matchers chain is split into two separate lists (RX only and TX only), which
solves a usecase of many RX or TX only rules that create a long chain of
RX/TX-only paths w/o the actual rules
- Patch 15 ignores modify TTL if device doesn't support it instead of
adding and unsupported action
- Patch 16 sets SMFS as a default steering mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
currently most cmdq APIs are unified in hclge_comm_cmd.c. Newly developed
cmdq APIs should also be placed in hclge_comm_cmd.c. So there is no need to
keep hclge_cmd.c and hclgevf_cmd.c.
This patch moves the hclge(vf)_cmd_send to hclge(vf)_main.c and deletes
the source files and makefile scripts.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq init and uninit APIs to replace the old APIs in
VF cmdq module init and uninit module. Then the old VF init and uninit
APIs is deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq init and uninit APIs to replace the old APIs in
PF cmdq module init and uninit modules. Then the old PF init and uninit
APIs is deleted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF and VF cmdq init and uninit APIs are also almost same espect the
suffixes of API names.
This patch creates common cmdq init and uninit APIs needed by PF and VF
cmdq modules. The next patch will use the new unified APIs to replace init
and uninit APIs in PF module.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq resource allocate/free/query APIs to replace
the old APIs in VF cmdq module and deletes the old cmdq resource APIs.
Still we kept hclgevf_cmd_setup_basic_desc name as a seam API to avoid too
many meaningless replacement.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses common cmdq resource allocate/free/query APIs to replace
the old APIs in PF cmdq module and deletes the old cmdq resource APIs.
Still we kept hclge_cmd_setup_basic_desc name as a seam API to avoid too
many meaningless replacement.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF and VF cmdq module resource allocate/free/query APIs are almost the
same espect the suffixes of API names. These same implementations bring
double development and bugfix work.
This patch creates common cmdq resource allocate/free/query APIs called by
PF and VF cmdq init/uninit APIs. The next patch will use the new unified
APIs to replace init/uninit APIs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclgevf_hw and deletes the old hardware description child
members. All the hclgevf_hw variables used in VF module is modified
according to the new hclgevf_hw.
Secondly hclgevf_cmd_send is refactored to use hclge_comm_cmd_send APIs.
The old functions called by hclgevf_cmd_send are all deleted. Still we kept
hclgevf_cmd_send to avoid too many meaningless modifications.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch firstly uses new hardware description struct hclge_comm_hw as
child member of hclge_hw and deletes the original child memebers of
hclge_hw. All the hclge_hw variables used in PF module is modified
according to the new hclge_hw.
Secondly hclge_cmd_send is refactored to use hclge_comm_cmd_send APIs. The
old functions called by hclge_cmd_send are deleted and hclge_cmd_send is
kept to avoid too many meaningless modifications.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch create new set of unified hclge_comm_cmd_send APIs for PF and VF
cmdq module. Subfunctions called by hclge_comm_cmd_send are also created
include cmdq result check, cmdq return code conversion and ring space
opertaion APIs.
These new common cmdq APIs will be used to replace the old PF and VF cmdq
APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch use new common struct hclge_desc to replace struct hclgevf_desc
in VF cmdq module and then delete the old struct hclgevf_desc.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PF and VF cmdq APIs use struct hclge(vf)_hw to describe cmdq
hardware information needed by hclge(vf)_cmd_send. There are a little
differences between its child struct hclge_cmq_ring and hclgevf_cmq_ring.
It is redundent to use two sets of structures to support same functions.
So this patch creates new set of common cmdq hardware description
structures(hclge_comm_hw) to unify PF and VF cmdq functions. The struct
hclge_desc is still kept to avoid too many meaningless replacement.
These new structures will be used to unify hclge(vf)_hw structures in PF
and VF cmdq APIs in next patches.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we plan to refactor PF and VF cmdq module. A new file folder
hns3_common will be created to store new common APIs used by PF and VF
cmdq module. Thus the PF and VF compilation process will both depends on
the hns3_common. This may cause parallel building problems if we add a new
makefile building unit.
So this patch combined the PF and VF makefile scripts to the top level
makefile to support the new hns3_common which will be created in the next
patch.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set SMFS (SW-managed flow steering) as a default steering mode
instead of DMFS (device-managed flow steering)
In SMFS, the driver writes the STEs (Steering Table Entries) directly
to the device's ICM, which allows for a higher rule insertion rate
than through using FW command interface, as it is done in DMFS.
SMFS/DMFS steering modes can be configured through devlink param
'flow_steering_mode'. The possible values are 'smfs' or 'dmfs'.
The desired 'flow_steering_mode' param value should be set before
enabling switchdev mode.
Example:
# devlink dev param set pci/0000:05:00.0 name flow_steering_mode smfs
# devlink dev eswitch set pci/0000:05:00.0 mode switchdev
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
When modifying TTL, packet's csum has to be recalculated.
Due to HW issue in ConnectX-5, csum recalculation for modify TTL
is supported through a work-around that is specifically enabled
by configuration.
If the work-around isn't enabled, ignore the modify TTL action
rather than adding an unsupported action.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Every matcher has RX and TX paths. When a new matcher is created, its RX
and TX start/end anchors are connected to the respective RX and TX anchors
of the previous and next matchers.
This creates a potential performance issue: when a certain rule is added
to a matcher, in many cases it is RX or TX only rule, which may create a
long chain of RX/TX-only paths w/o the actual rules.
This patch aims to handle this issue.
RX and TX matchers are now handled separately: matcher connection in the
matchers chain is split into two separate lists: RX only and TX only.
when a new matcher is created, it is initially created 'detached' - its
RX/TX members are not inserted into the table's matcher list.
When an actual rule is added, only its appropriate RX or TX nic matchers
are then added to the table's nic matchers list and inserted into its
place in the chain of matchers.
I.e., if the rule that is being added is an RX-only rule, only the RX
part of the matcher will be connected to the chain, while TX part of the
matcher remains detached and doesn't prolong the TX chain of the matchers.
Same goes for rule deletion: when the last RX/TX rule of the nic matcher
is destroyed, the nic matcher is removed from its list.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Match on geneve_tlv_option_0_exist field on devices that support STEv1.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Vincent Mailhol