"ap" is the address of sdata->u.ap so it can never be NULL here. Also
we dereferenced it on the previous line. I removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using skb_header_cloned to check if it's safe to write to the skb is not
enough - mac80211 also touches the tailroom of the skb.
Initially this check was only used to increase a counter, however this
commit changed the code to also skip skb data reallocation if no extra
head/tailroom was needed:
commit 4cd06a344d
mac80211: skip unnecessary pskb_expand_head calls
It added a regression at least with iwl3945, which is fixed by this patch.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should decrease un-necessary flushes, on/off channel work,
and channel changes in cases where the only scanned channel is
the current operating channel.
* Removes SCAN_OFF_CHANNEL flag, uses SDATA_STATE_OFFCHANNEL
and is-scanning flags instead.
* Add helper method to determine if we are currently configured
for the operating channel.
* Do no blindly go off/on channel in work.c Instead, only call
appropriate on/off code when we really need to change channels.
Always enable offchannel-ps mode when starting work,
and disable it when we are done.
* Consolidate ieee80211_offchannel_stop_station and
ieee80211_offchannel_stop_beaconing, call it
ieee80211_offchannel_stop_vifs instead.
* Accept non-beacon frames when scanning on operating channel.
* Scan state machine optimized to minimize on/off channel
transitions. Also, when going on-channel, go ahead and
re-enable beaconing. We're going to be there for 200ms,
so seems like some useful beaconing could happen.
Always enable offchannel-ps mode when starting software
scan, and disable it when we are done.
* Grab local->mtx earlier in __ieee80211_scan_completed_finish
so that we are protected when calling hw_config(), etc.
* Pass probe-responses up the stack if scanning on local
channel, so that mlme can take a look.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On review of 'zd1211rw: implement beacon fetching and handling
ieee80211_get_buffered_bc()', Christian Lamparter noted that [1]:
Since zd_beacon_done also uploads the next beacon so long in advance,
there could be an equally long race between the outdated state of the
next beacon's DTIM broadcast traffic indicator (802.11-2007 7.3.2.6)
which -in your case- was uploaded almost a beacon interval ago and
the xmit of ieee80211_get_buffered_bc *now*.
The dtim bc/mc bit might be not set, when a mc/bc arrived after the
beacon was uploaded, but before the "beacon done event" from the
hardware. So, dozing stations don't expect the broadcast traffic
and of course, they might miss it completely.
It's probably better to fix this in mac80211 (see the attached hack).
[1] http://marc.info/?l=linux-wireless&m=129435041117256&w=2
CC: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rate-control is performed in HW, we cannot calculate frame
duration as we do not have the skb transmission rate in SW.
ieee80211_tx_h_calculate_duration() should only be called when
ieee80211_tx_h_rate_ctrl() has been called before to initialize data
in skb->cb. This doesn't happen for drivers with HW rate-control.
Fixes the following warning when operating in AP-mode
in a driver with HW rate-control.
WARNING: at net/mac80211/tx.c:57 ieee80211_duration+0x54/0x1d8 [mac80211]()
Modules linked in: wl1271_sdio wl1271 firmware_class crc7 mac80211 cfg80211
[<c0046090>] (unwind_backtrace+0x0/0x124) from [<c0064c10>] (warn_slowpath_common+0x4c/0x64)
[<c0064c10>] (warn_slowpath_common+0x4c/0x64) from [<c0064c40>] (warn_slowpath_null+0x18/0x1c)
[<c0064c40>] (warn_slowpath_null+0x18/0x1c) from [<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211])
[<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211]) from [<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211])
[<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211]) from [<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211])
[<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211]) from [<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211])
[<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211]) from [<c0069a9c>] (tasklet_action+0x68/0xbc)
[<c0069a9c>] (tasklet_action+0x68/0xbc) from [<c006a044>] (__do_softirq+0x84/0x114)
[<c006a044>] (__do_softirq+0x84/0x114) from [<c006a1b8>] (do_softirq+0x48/0x54)
[<c006a1b8>] (do_softirq+0x48/0x54) from [<c006a4f8>] (local_bh_enable+0x98/0xcc)
[<c006a4f8>] (local_bh_enable+0x98/0xcc) from [<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271])
[<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271]) from [<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271])
[<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271]) from [<c0076864>] (process_one_work+0x208/0x350)
[<c0076864>] (process_one_work+0x208/0x350) from [<c0076e14>] (worker_thread+0x1cc/0x300)
[<c0076e14>] (worker_thread+0x1cc/0x300) from [<c007bb88>] (kthread+0x84/0x8c)
[<c007bb88>] (kthread+0x84/0x8c) from [<c0041494>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.
To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mesh is disabled, mac80211 was returning
beacons with an empty mesh ID. That isn't
desirable, even if drivers shouldn't be trying
to get beacons to start with.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mppath is mesh related parameter and maybe unused
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrote code for checking if the destination is proxied by a mesh portal, to facilitate better
understanding of the functionality.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a bunch of
warning: ‘inline’ is not at beginning of declaration
messages when building a 'make allyesconfig' kernel with -Wextra.
These warnings are trivial to kill, yet rather annoying when building with
-Wextra.
The more we can cut down on pointless crap like this the better (IMHO).
A previous patch to do this for a 'allnoconfig' build has already been
merged. This just takes the cleanup a little further.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixed a bug where if a mesh interface has a different MAC address from its bridge
interface, then it would not be able to send data traffic to any other mesh node.
This also adds support for communication between mesh nodes and external bridged
nodes by using a 6 address format if the source is a node within the mesh and the
destination is an external node proxied by a mesh portal.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.
All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an skb is shared, it needs to be duplicated, along with its data buffer.
If the skb does not have enough headroom, using skb_copy might cause the data
buffer to be copied twice (once by skb_copy and once by pskb_expand_head).
Fix this by using skb_clone initially and letting ieee80211_skb_resize sort
out the rest.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the skb is not cloned and we don't need any extra headroom, there
is no point in reallocating the skb head.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4. If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).
The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft. See
section 7.1.3.6.3 in current draft (8.0).
Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats. But I thought I better
remove it before someone does start using it.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last_tx_rate field was also updated for non-data frames that are
often sent with a lower rate (for example management frames at 1 Mbps).
This is confusing when the data rate is actually much higher.
Hence, only update the last_tx_rate field with tx rate information
gathered from last data frames.
If the rate control algorithm filled in txrc.reported_rate we don't need
to verify this information.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for frame injection to work properly for some use cases
(e.g., finding the station entry and keys for encryption), mac80211
needs to find the correct sdata entry. This works when the main vif
is in AP mode, but commit a2c1e3dad5
broke this particular use case for station main vif. While this type of
injection is quite unusual operation, it has some uses and we should fix
it. Do this by changing the monitor vif sdata selection to allow station
vif to be selected instead of limiting it to just AP vifs. We still need
to skip some iftypes to avoid selecting unsuitable vif for injection.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hdr pointer is left dangling after call to ieee80211_skb_resize. This
can cause guards around mesh path selection to fail.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are subqueue helpers so that we don't
need to get the TX queue and then wake/stop
it, use those helpers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Support this
in mac80211 via the cfg80211 API for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to specify their own set of cipher
suites to advertise vendor-specific ciphers. The
driver is then required to implement hardware
crypto offload for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_hdr only used when CONFIG_MAC80211_MESH is defined
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function ieee80211_subif_start_xmit the logic related with
meshdrlen is under CONFIG_MAC80211_MESH macro, but in one place it isn't.
This is some update for this
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I just had the following:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-tx.c:574 iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]()
Call Trace:
<IRQ> [<ffffffff8105c5df>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8105c63a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0290b46>] iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]
[<ffffffffa027076c>] iwl_mac_tx+0x5c/0x260 [iwlagn]
[<ffffffffa01bdf5b>] __ieee80211_tx+0x10b/0x1a0 [mac80211]
[<ffffffffa01bfb86>] ieee80211_tx_pending+0x186/0x2d0 [mac80211]
[<ffffffff81062ea5>] tasklet_action+0x125/0x130
[<ffffffff810634a6>] __do_softirq+0x106/0x270
[<ffffffff8100c09c>] call_softirq+0x1c/0x30
iwlagn 0000:02:00.0: Attempting to modify non-existing station 107
Note that 107 == 0x6b which is slab poison.
The reason is that mac80211 passed a freed station
pointer to mac80211, because as it happened iwlwifi
reset itself while mac80211 was disconnecting from
the network.
It turns out that we do take care to look up the
station pointer in ieee80211_tx_pending_skb, but
then don't use it, which obviously is a bug. Fix
this by removing the ieee80211_tx_h_sta handler
and assigning the station pointer directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver or rate control requests starting
or stopping an aggregation session, that currently
causes a direct callback into the driver, which
could potentially cause locking problems. Also,
the functions need to be callable from contexts
that cannot sleep, and thus will interfere with
making the ampdu_action callback sleeping.
To address these issues, add a new work item for
each station that will process any start or stop
requests out of line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each TX
aggregation session and additionally keep a
state bitmap indicating the state it is in.
By using RCU to protect the pointer, moving
the state into the structure and some locking
trickery we can avoid locking when the TX agg
session is fully operational.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also simplify the flags assignment into a single statement at the
end of ieee80211_beacon_get_tim.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently whenever rts thresold is set, every packet will use RTS
protection no matter its size exceeds the threshold or not. This is
due to a bug in the rts threshold check.
if (len > tx->local->hw.wiphy->rts_threshold) {
txrc.rts = rts = true;
}
Basically it is comparing an int (len) and a u32 (rts_threshold),
and the variable len is assigned as:
len = min_t(int, tx->skb->len + FCS_LEN,
tx->local->hw.wiphy->frag_threshold);
However, when frag_threshold is "-1", len is always "-1", which is
0xffffffff therefore rts is always set to true.
CC: stable@kernel.org
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_cleanup timer is used to periodically expire buffered frames from the
tx buf. The timer is executing periodically, regardless of the need for it.
This is wasting resources.
Fix this simply by not restarting the sta_cleanup timer if the tx buffer was
empty. Restart the timer when there is some more tx-traffic.
Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BIP (part of IEEE 802.11w) is only supposed to be used with
group-addressed frames. We ended up picking it as a default mechanism
for every management whenever we did not have a STA entry for the
destination (e.g., for Probe Response to a STA that is not
associated). While the extra MMIE in the end of management frames
should not break frames completed in most cases, there is no point in
doing this. Fix key selection to pick the default management key only
if the frame is sent to multicast/broadcast address and the frame is a
robust management frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need "sdata" any more after:
d84f323477
mac80211: remove dev_hold/put calls
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many drivers would like to sleep during station
addition and removal, and currently have a high
complexity there from not being able to.
This introduces two new callbacks sta_add() and
sta_remove() that drivers can implement instead
of using sta_notify() and that can sleep, and
the new sta_add() callback is also allowed to
fail.
The reason we didn't do this previously is that
the IBSS code wants to insert stations from the
RX path, which is a tasklet, so cannot sleep.
This patch will keep the station allocation in
that path, but moves adding the station to the
driver out of line. Since the addition can now
fail, we can have IBSS peer structs the driver
rejected -- in that case we still talk to the
station but never tell the driver about it in
the control.sta pointer. If there will ever be
a driver that has a low limit on the number of
stations and that cannot talk to any stations
that are not known to it, we need to do come up
with a new strategy of handling larger IBSSs,
maybe quicker expiry or rejecting peers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upstream radiotap has adopted the namespace
proposal David Young made and I then took care
of, for which I had adapted the radiotap parser
as a library outside the kernel. This brings
the in-kernel parser up to speed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When injecting frames, mac80211 currently looks for the first AP
interface that matches the source address of the injected frame.
This breaks when such a frame is directed at a STA that has been moved
to a VLAN. This patch fixes it by using sta_info_get_bss instead of
sta_info_get, which also finds stations belonging to a VLAN interface
of the same BSS as the AP interface.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an injected frame gets buffered for a powersave STA or filtered
and retransmitted, mac80211 attempts to parse the radiotap header
again, which doesn't work because it's gone at that point.
This patch adds a new flag for checking the availability of a radiotap
header, so that it only attempts to parse it once, reusing the tx info
on the next call to ieee80211_tx().
This fixes severe issues with rekeying in AP mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What a stupid mistake. In
commit 813d766940
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Sun Jan 17 01:47:58 2010 +0100
mac80211: move control.hw_key assignment
I inserted code testing the wrong flags field,
which means that the test is almost always true
(it's really testing for the peer's WMM support)
and thus the later parts of the stack assume hw
crypto will be done even if that's not true.
Obviously, that broke software crypto. Maxim
said so specifically, and Jochen probably uses
some cipher that iwl3945 doesn't support in
hardware, which might also explain that Maxim
reports that even hw crypto is broken.
Fix this to test the right flags field.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Reported-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin reported a crash in ieee80211_tx_h_select_key():
http://marc.info/?l=linux-wireless&m=126419655108528&w=2
This is a regression from patch "mac80211: move control.hw_key assignment".
Fix it as suggested by Johannes, adding an else statement to make sure
that tx->key is not accessed when it's null.
Compile-tested only.
Reported-by: Pavel Roskin <proski@gnu.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_tx_h_select_key might decide that a frame
need not be encrypted at all, in which case it will
clear tx->key. In that case it may crash if a key
was previously selected, e.g. as the default key.
This is also due to my patch
"mac80211: move control.hw_key assignment".
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In an earlier commit,
mac80211: disable software retry for now
Pavel Roskin reported a problem that seems to be due to
software retry of already transmitted frames. It turns
out that we've never done that correctly, but due to
some recent changes it now crashes in the TX code. I've
added a comment in the patch that explains the problem
better and also points to possible solutions -- which
I can't implement right now.
I disabled software retry of failed/filtered frames
because it was broken. With the work of the previous
patches, it now becomes fairly easy to re-enable it
by adding a flag indicating that the frame shouldn't
be modified, but still running it through the transmit
handlers to populate the control information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 asks a driver to encrypt a frame, it
must assign the control.hw_key pointer for it to
know which key to use etc. Currently, mac80211 does
this whenever it would software-encrypt a frame.
Change the logic of this code to assign the hw_key
pointer when selecting the key, and later check it
when deciding whether to encrypt the frame or let
it be encrypted by the hardware. This allows us to
later simply skip the encryption function since it
no longer modifies the TX control.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no value in setting a flag that will
never be checked after this point, this seems
to be legacy code -- I think previously the
flag was used to check whether to encrypt the
frame or not. Now, however, the flag need not
be set, and setting it actually interferes if
the frame will be processed again later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This TX handler is used only for assigning the
station pointer in the control information, so
give it a better name. Also move it before rate
control.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make U-APSD client mode effective, we must not wake up from dynamic power
save when transmitting frames. So if dynamic power save is enabled, it needs
check the queue the transmitted packet is in and decide if we need to wake
up or not.
In a perfect world, where all packets would have correct QoS tags, U-APSD
enabled queues should not trigger wakeup from power save. But in the real
world, where very few packets have correct QoS tags, this won't work. For
example, if only voip class has U-APSD enabled and we send a packet in voip
class, but the packets we receive are in best effort class, we would receive
the packets with the legacy power save method. And that would increase
latencies too much from a voip application point of view.
The workaround is to enable U-APSD for all qeueus and still use dynamic ps
wakeup for all other queues except voip. That way we can still save power
with a voip application and not sacrifice latency. Normal traffic (in
background, best effort or video class) would still trigger wakeup from
dynamic power save.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently dynamic ps check is in ieee80211_xmit(), but it's cleaner
to have a separate tx handler for this. Also this is a prerequisite for
U-APSD client mode which needs to know the queue frame is in.
Also need_dynamic_ps() function is embedded to the tx handler.
No functional changes expect that the code is run in a later phase than
originally.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If frames are transmitted on 4-addr ap vlan interfaces with no station,
they end up being transmitted unencrypted, even if the ap interface
uses WPA. This patch add some sanity checking to make sure that this
does not happen.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Certain type of hardware, for example wl1251 and wl1271, need a template
for the Probe Request. Create a function ieee80211_probereq_get() which
creates the template and drivers send it to hardware.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware, for example wl1251 and wl1271, handle the transmission
of power save related frames in hardware, but the driver is responsible
for creating the templates. It's better to create the templates in mac80211,
that way all drivers can benefit from this.
Add two new functions, ieee80211_pspoll_get() and ieee80211_nullfunc_get()
which drivers need to call to get the frame. Drivers are also responsible
for updating the templates after each association.
Also new struct ieee80211_hdr_3addr is added to ieee80211.h to make it
easy to calculate length of the Nullfunc frame.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend struct cfg80211_bitrate_mask to actually use a bitfield mask
instead of just a single fixed or maximum rate index. This change
itself does not modify the behavior (except for debugfs files), but it
prepares cfg80211 and mac80211 for a new nl80211 command for setting
which rates can be used in TX rate control.
Since frames are now going through the rate control algorithm
unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now
be removed. The RC implementations can use the rate_idx_mask value to
optimize their behavior if only a single rate is enabled.
The old max_rate_idx in struct ieee80211_tx_rate_control is maintained
(but commented as deprecated) for backwards compatibility with existing
RC implementations. Once these implementations have been updated to
use the more generic rate_idx_mask, the max_rate_idx value can be
removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the basic rate set is configured to not include the lowest rate
(e.g., basic rate set = 6, 12, 24 Mbps in IEEE 802.11g mode), the AP
should not send out broadcast frames at 1 Mbps. This type of
configuration can be used to optimize channel usage in cases where
there is no need for backwards compatibility with IEEE 802.11b-only
devices.
In AP mode, mac80211 was unconditionally using the lowest rate for
Beacon frames and similarly, with all rate control algorithms that use
rate_control_send_low(), the lowest rate ended up being used for all
broadcast frames (and all unicast frames that are sent before
association). Change this to take into account the basic rate
configuration in AP mode, i.e., use the lowest rate in the basic rate
set instead of the lowest supported rate when selecting the rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I removed the master netdev, we've been
keeping internal queues only, and even before
that we never told the networking stack above
the virtual interfaces about congestion. This
means that packets are queued in mac80211 and
the upper layers never know, possibly leading
to memory exhaustion and other problems.
This patch makes all interfaces multiqueue and
uses ndo_select_queue to put the packets into
queues per AC. Additionally, when the driver
stops a queue, we now stop all corresponding
queues for the virtual interfaces as well.
The injection case will use VO by default for
non-data frames, and BE for data frames, but
downgrade any data frames according to ACM. It
needs to be fleshed out in the future to allow
chosing the queue/AC in radiotap.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always using netif_running(sdata->dev)
use ieee80211_sdata_running(sdata) now which is
just an inline containing netif_running() for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 suspends it calls a driver's suspend callback
as a last step and after that the driver assumes no calls will
be made to it until we resume and its start callback is kicked.
If such calls are made, however, suspend can end up throwing
hardware in an unexpected state and making the device unusable
upon resume.
Fix this by preventing mac80211 to schedule dynamic_ps_disable_work
by checking for when mac80211 starts to suspend and starts
quiescing. Frames should be allowed to go through though as
that is part of the quiescing steps and we do not flush the
mac80211 workqueue since it was already done towards the
beginning of suspend cycle.
The other mac80211 issue will be hanled in the next patch.
For further details see refer to the thread:
http://marc.info/?t=126144866100001&r=1&w=2
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station management currently uses the virtual
interface, but you cannot add the same station to
multiple virtual interfaces if you're communicating
with it in multiple ways.
This restriction should be lifted so that in the
future we can, for instance, support bluetooth 3
with an access point that mac80211 is already
associated to.
We can do that by requiring all sta_info_get users
to provide the virtual interface and making the RX
code aware that an address may match more than one
station struct. Thanks to the previous patches this
one isn't all that large and except for the RX and
TX status paths changes has low complexity.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.
The rate control algorithms also need TX status, but
they don't require it.
Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.
This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices implement the entire rate control in
firmware in some way, like wl1271 or like iwlwifi
which does some things in software but not a lot.
Therefore generic software rate control is rather
useless for them and just adds avoidable overhead
to the transmit path.
It's fairly simple to let drivers indicate that
they do not need rate control, but they need to
fulfil a number of conditions that we encode in
WARN_ONs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The netdev broadcast address cannot change from
all-ones so there's no need to use it; we can
instead hard-code it. Since we already have an
instance in tkip.c, which will be shared if it
is marked static const, doing this reduces text
size at no data/bss cost.
The real motivation for this is, of course, the
desire to get rid of almost all uses of netdevs
in mac80211 so that auditing their use becomes
easier.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we move the rcu sections a little, there's
no need to touch the device refcount.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BSSID is now set to the TA.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations it might be useful to run a network with an
Access Point and multiple clients, but with each client bridged
to a network behind it. For this to work, both the client and the
AP need to transmit 4-address frames, containing both source and
destination MAC addresses.
With this patch, you can configure a client to communicate using
only 4-address frames for data traffic.
On the AP side you can enable 4-address frames for individual
clients by isolating them in separate AP VLANs which are configured
in 4-address mode.
Such an AP VLAN will be limited to one client only, and this client
will be used as the destination for all traffic on its interface,
regardless of the destination MAC address in the packet headers.
The advantage of this mode compared to regular WDS mode is that it's
easier to configure and does not require a static list of peer MAC
addresses on any side.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices require that all frames to a station
are flushed when that station goes into powersave
mode before being able to send frames to that
station again when it wakes up or polls -- all in
order to avoid reordering and too many or too few
frames being sent to the station when it polls.
Normally, this is the case unless the station
goes to sleep and wakes up very quickly again.
But in that case, frames for it may be pending
on the hardware queues, and thus races could
happen in the case of multiple hardware queues
used for QoS/WMM. Normally this isn't a problem,
but with the iwlwifi mechanism we need to make
sure the race doesn't happen.
This makes mac80211 able to cope with the race
with driver help by a new WLAN_STA_PS_DRIVER
per-station flag that can be controlled by the
driver and tells mac80211 whether it can transmit
frames or not. This flag must be set according to
very specific rules outlined in the documentation
for the function that controls it.
When we buffer new frames for the station, we
normally set the TIM bit right away, but while
the driver has blocked transmission to that sta
we need to avoid that as well since we cannot
respond to the station if it wakes up due to the
TIM bit. Once the driver unblocks, we can set
the TIM bit.
Similarly, when the station just wakes up, we
need to wait until all other frames are flushed
before we can transmit frames to that station,
so the same applies here, we need to wait for
the driver to give the OK.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The multi-line code in this macro wasn't wrapped
in do {} while (0) so we cannot use it in an if()
branch safely in the future -- fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 is asked to buffer multicast frames
in AP mode, it will not set the flag indicating
that the frames should be sent after the DTIM
beacon for those frames buffered in software. Fix
this little inconsistency by always setting that
flag in the buffering code path.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compared to ieee80211_beacon_get(), the new function
ieee80211_beacon_get_tim() returns information on the
location and length of the TIM IE, which some drivers
need in order to generate the TIM on the device. The
old function, ieee80211_beacon_get(), becomes a small
static inline wrapper around the new one to not break
all drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In TX path it was assumed that dynamic power save works only if
IEEE80211_HW_PS_NULLFUNC_STACK is set. But is not the case, there are
devices which have nullfunc support in hardware but need mac80211
to handle dynamic power save timers, TI's wl1251 is one of them.
The fix is to not check for IEEE80211_HW_PS_NULLFUNC_STACK in
is_dynamic_ps_enabled(), instead check IEEE80211_HW_SUPPORTS_PS and
IEEE80211_HW_SUPPORTS_DYNAMIC_PS flags and act accordingly.
Tested with wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor dynamic power save checks to a function of it's own for better
readibility. No functional changes.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hostapd injects a frame, e.g. an authentication or association
response, mac80211 looks for a suitable access point virtual interface
to associate the frame with based on its source address. This makes it
possible e.g. to correctly assign sequence numbers to the frames.
A small typo in the ethernet address comparison statement caused a
failure to find a suitable ap interface. Sequence numbers on such
frames where therefore left unassigned causing some clients
(especially windows-based 11b/g clients) to reject them and fail to
authenticate or associate with the access point. This patch fixes the
typo in the address comparison statement.
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving data frames, we can send them only to
the interface they belong to based on transmitting
station (this doesn't work for probe requests). Also,
don't try to handle other frames for AP_VLAN at all
since those interface should only receive data.
Additionally, the transmit side must check that the
station we're sending a frame to is actually on the
interface we're transmitting on, and not transmit
packets to functions that live on other interfaces,
so validate that as well.
Another bug fix is needed in sta_info.c where in the
VLAN case when adding/removing stations we overwrite
the sdata variable we still need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consider the following step-by step:
1. A STA authenticates and associates with the AP and exchanges
traffic.
2. The STA reports to the AP that it is going to PS state.
3. Some time later the STA device goes to the stand-by mode (not only
its wi-fi card, but the device itself) and drops the association state
without sending a disassociation frame.
4. The STA device wakes up and begins authentication with an
Auth frame as it hasn't been authenticated/associated previously.
At the step 4 the AP "remembers" the STA and considers it is still in
the PS state, so the AP buffers frames, which it has to send to the STA.
But the STA isn't actually in the PS state and so it neither checks
TIM bits nor reports to the AP that it isn't power saving.
Because of that authentication/[re]association fails.
To fix authentication/[re]association stage of this issue, Auth, Assoc
Resp and Reassoc Resp frames are transmitted disregarding of STA's power
saving state.
N.B. This patch doesn't fix further data frame exchange after
authentication/[re]association. A patch in hostapd is required to fix
that.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mesh frames that could not be immediately resolved were queued with a NULL
info->control.vif. This patch moves the call to mesh_nexthop_lookup closer to
the point where it is handed over to ieee80211_tx(). This ensures that the
unresolved frames are ready to be sent once the path is resolved.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address. This was done to avoid interactions with widely
deployed lazy-WDS access points.
This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward. The
address fields used for group addressed frames is:
In 802.11 header
ToDS:0 FromDS:1
addr1: DA (broadcast/multicast address)
addr2: TA
addr3: Mesh SA
In address extension header:
addr4: SA (only present if frame was proxied)
Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's really easier to read if it's not indented
as much, so invert the condition and rearrange
the code so the smaller chunk is indented instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to mask the variable with 0xFFF0
since we ever only use it as a u16 and the lowest
four bits can't ever be non-zero. The compiler
cannot infer the latter, and therefore has to emit
code to do the masking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When encryption is used, the number of bytes
sent to the peer increases by the IV and ICV.
This is accounted if software encryption is
used, but not if the devices does hardware
encryption. To make the numbers comparable,
never account for that overhead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have a lot of frames to transmit at once, for
instance with fragmentation, it can be an optimisation
to only tell the DMA engine about them on the last
fragment/frame to avoid banging the IO too much. This
patch allows implementation such an optimisation by
telling the driver when more frames can be expected.
Currently, this is used by mac80211 only on fragmented
frames, but could also be used in the future on other
frames when the queue was full and there are multiple
frames pending.
Note that drivers need to be careful when using this
flag, they need to kick their DMA engines not just
when this flag is clear, but also when the queue gets
full so that progress can be made.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When enqueuing packets on the internal packet queue, we
need to ensure that we have a valid vif pointer since
that is required since the net namespace work. Add some
assertions to verify this, but also don't crash is for
some reason we don't end up with a vif pointer -- warn
and drop the packet in all these cases.
Since this code touches a number of hotpaths, it is
intended to be temporary, or maybe configurable in the
future, at least the bit that is in the path that gets
hit for every packet, ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was caused by patch:
"mac80211: cooperate more with network namespaces"
The version of the patch applied doesn't match Johannes' latest:
http://johannes.sipsolutions.net/patches/kernel/all/LATEST/NNN-mac80211-netns.patch
The skb->cb virtual interface data wasn't being reset for
reuse so ath9k pooped out when trying to dereference the
private rate control info from the skb.
BUG: unable to handle kernel NULL pointer dereference
RIP: 0010:[<ffffffffa0258173>] ath_tx_rc_status+0x33/0x150 [ath9k]
<-- snip etc -->
Reported-by: Davide Pesavento <davidepesa@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.
Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.
(Also remove a now dead function)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Bob Copeland <me@bobcopeland.com>
Tested-by: Bob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new scan flag "SCAN_OFF_CHANNEL" which basically tells us
that we are currently on a different channel for scanning and cannot
RX/TX. "SCAN_SW_SCANNING" tells us that we are currently running a
software scan but we might as well be on the operating channel to RX/TX.
While "SCAN_SW_SCANNING" is set during the whole scan "SCAN_OFF_CHANNEL"
is set when leaving the operating channel and unset when coming back.
Introduce two new scan states "SCAN_LEAVE_OPER_CHANNEL" and
"SCAN_ENTER_OPER_CHANNEL" which basically implement the functionality we
need to leave the operating channel (send a nullfunc to the AP and stop
the queues) and enter it again (send a nullfunc to the AP and start the
queues again).
Enhance the scan state "SCAN_DECISION" to switch back to the operating
channel after each scanned channel. In the future it sould be simple
to enhance the decision state to scan as much channels in a row as the
qos latency allows us.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are still two places in mac80211 that hardcode
the initial net namespace (init_net). One of them is
mandated by cfg80211 and will be removed by a separate
patch, the other one is used for finding the network
device of a pending packet via its ifindex.
Remove the latter use by keeping track of the device
pointer itself, via the vif pointer, and avoid it
going stale by dropping pending frames for a given
interface when the interface is removed.
To keep track of the vif pointer for the correct
interface, change the info->control.vif pointer's
internal use to always be the correct vif, and only
move it to the vif the driver expects (or NULL for
monitor interfaces and injected packets) right before
giving the packet to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The removal of the master netdev broke the mesh forwarding path. This patch
fixes it by using the new internal 'pending' queue.
As a result of this change, mesh forwarding no longer does the inefficient
802.11 -> 802.3 -> 802.11 conversion that was done before.
[Changes since v1]
Suggested by Johannes:
- Select queue before adding to mpath queue
- ieee80211_add_pending_skb -> ieee80211_add_pending_skbs
- Remove unnecessary header wme.h
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_xmit() cannot be called with tasklets enabled
because it is normally called from within a tasklet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we're associated we should be able to send data to
target sta. If we cannot we may be trying to use the incorrect
band to talk to the sta. Lets catch any such cases, warn, and
drop the frames to not invalidate assumptions being made on
rate control algorithms when they have a valid sta to
communicate with. Any such cases should be handled and fixed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The location of the 802.11 header is calculated incorrectly due to a
wrong placement of parentheses. Found by kmemcheck.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want to trigger moving between PS mode during scan,
because then we will sometimes end up sending nullfunc frames
during scan. We're supposed to only send one prior to scan
and after scan.
This fixes an oops which occured due to an assert in ath9k:
http://marc.info/?l=linux-wireless&m=124277331319024
The assert was happening because the rate control algorithm
figures it should find at least one valid dual stream or
single stream rate. Since we allow mac80211 to send nullfunc
frames during scan and dynamic PS was enabled at times we ended
up trying to send nullfunc frames for the target sta on the
wrong band for which we have no valid rate to communicate with
it. This breaks the assumptions in rate control.
We determine we also need to disable moving between PS modes
when not associated so lets just add that now as well, and we
should not have a ps_sdata when that interface cannot actually
go into PS because it's not associated.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return type has more than two values, but it can validly
only ever return TX_DROP and TX_CONTINUE, so use a bool
instead of ieee80211_tx_result.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.
Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the duration field for TX frames, skip the update for
PS-Poll frames that use this field for other purposes (AID).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's this internal wifi_wme_noack_test variable that
we use to set the QoS control if set. For one, it is
unlikely that it is set. Secondly, if set it needs to
influence the IEEE80211_TX_CTL_NO_ACK TX control flag,
and finally we should also be able to set it at all, so
make it available in debugfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To deter future rate scaling algorithm writers from requesting NO_ACK
packets to be retried, throw a WARN_ON_ONCE if the algorithm hands us
a try count over 1 for NO_ACK packet.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.
All calls are now written as
drv_<op>(local, ...);
instead of
local->ops-><op>(&local->hw, ...);
Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fragmentation threshold is defined to be including the
FCS, and the code that sets the TX_FRAGMENTED flag correctly
accounts for those four bytes. The code that verifies this
doesn't though, which could lead to spurious warnings and
frames being dropped although everything is ok. Correct the
code by accounting for the FCS.
(JWL -- The problem is described here:
http://article.gmane.org/gmane.linux.kernel.wireless.general/32205 )
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts mac80211 to the new cfg80211 IBSS API, the
wext handling functions are called where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets IEEE80211_TX_CTL_CLEAR_PS_FILT for outgoing
frames for a half-wake station.
this is necessary if one wants to get ps-poll working properly with a p54 ap.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of stopping the entire AC queue when enabling aggregation
(which was only done for hardware with aggregation queues) buffer
the packets for each station, and release them to the pending skb
queue once aggregation is turned on successfully.
We get a little more code, but it becomes conceptually simpler and
we can remove the entire virtual queue mechanism from mac80211 in
a follow-up patch.
This changes how mac80211 behaves towards drivers that support
aggregation but have no hardware queues -- those drivers will now
not be handed packets while the aggregation session is being
established, but only after it has been fully established.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We just found a bug in zd1211rw where it would reject
packets in the ->tx() method but leave them modified,
which would cause retransmit attempts with completely
bogus skbs, eventually leading to a panic due to not
having enough headroom in those.
This patch adds a sanity check to mac80211 to catch
such driver mistakes; in this case we warn and drop
the skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tx takes a struct ieee80211_tx_data argument, but only
uses a few of its members, namely 'skb' and 'sta'. Make that explicit,
so that less internal knowledge is required in ieee80211_tx_pending
and the possibility of introducing errors here is removed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pending packets code is quite incomprehensible, uses memory barriers
nobody really understands, etc. This patch reworks it entirely, using
the queue spinlock, proper stop bits and the skb queues themselves to
indicate whether packets are pending or not (rather than a separate
variable like before).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Internally, mac80211 requires the skb's queue mapping to be set
to the AC queue, not the virtual A-MPDU queue. This is not done
correctly currently, this patch moves the code down to directly
before the driver is invoked and adds a comment that it will be
moved into the driver later.
Since this requires __ieee80211_tx() to have the sta pointer,
make sure to provide it in ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmentation currently uses an allocated array to store the
fragment skbs, and then keeps track of which have been sent
and which are still pending etc. This is rather complicated;
make it simpler by just chaining the fragments into skb->next
and removing from that list when sent. Also simplifies all
code that needs to touch fragments, since it now only needs
to walk the skb->next list.
This is a prerequisite for fixing the stored packet code,
which I need to do for proper aggregation packet storing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_tx_h_check_assoc() was dropping everything else than probe
requests during software scan. So the nullfunc frame with the power save
bit was dropped and AP never received it. This meant that AP never
buffered any frames for the station during software scan.
Fix this by allowing to transmit both probe request and nullfunc frames
during software scan. Tested with stlc45xx.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This inline is useless and actually makes the code _longer_
rather than shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible to hit a kernel panic on NULL pointer dereference in
dev_queue_xmit() when sending power save buffered frames to a STA that
woke up from sleep. This happened when the buffered frame was requeued
for transmission in ap_sta_ps_end(). In order to avoid the panic, copy
the skb->dev and skb->iif values from the first fragment to all other
fragments.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits out the ibss code and data from managed (station) mode.
The reason to do this is to better separate the state machines, and have
the code be contained better so it gets easier to determine what exactly
a given change will affect, that in turn makes it easier to understand.
This is quite some churn, especially because I split sdata->u.sta into
sdata->u.mgd and sdata->u.ibss, but I think it's easier to maintain that
way. I've also shuffled around some code -- null function sending is only
applicable to managed interfaces so put that into that file, some other
functions are needed from various places so put them into util, and also
rearranged the prototypes in ieee80211_i.h accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware with AMPDU queues currently has broken aggregation.
This patch fixes it by making all A-MPDUs go over the regular AC queues,
but keeping track of the hardware queues in mac80211. As a first rough
version, it actually stops the AC queue for extended periods of time,
which can be removed by adding buffering internal to mac80211, but is
currently not a huge problem because people rarely use multiple TIDs
that are in the same AC (and iwlwifi currently doesn't operate as AP).
This is a short-term fix, my current medium-term plan, which I hope to
execute soon as well, but am not sure can finish before .30, looks like
this:
1) rework the internal queuing layer in mac80211 that we use for
fragments if the driver stopped queue in the middle of a fragmented
frame to be able to queue more frames at once (rather than just a
single frame with its fragments)
2) instead of stopping the entire AC queue, queue up the frames in a
per-station/per-TID queue during aggregation session initiation,
when the session has come up take all those frames and put them
onto the queue from 1)
3) push the ampdu queue layer abstraction this patch introduces in
mac80211 into the driver, and remove the virtual queue stuff from
mac80211 again
This plan will probably also affect ath9k in that mac80211 queues the
frames instead of passing them down, even when there are no ampdu queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.28.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Monitor mode is able to TX by using injected frames. We should
not allow injected frames to be sent unless allowed by regulatory
rules. Since AP mode uses a monitor interfaces to transmit
management frames we have to take care to not break AP mode as
well while resolving this. We can deal with this by allowing compliant
APs solutions to inform mac80211 if their monitor interface is
intended to be used for an AP by setting a cfg80211 flag for the
monitor interface. hostapd, for example, currently does its own
checks to ensure AP mode is not used on channels which require radar
detection. Once such solutions are available it can can add this
flag for monitor interfaces.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ADDBA request Action frame was sent out before 4-way handshake was
completed and the initial 802.11w code ended up dropping the frame
even if MFP was not enabled. While the sending of Action frames this
early is not really a good idea (will break with MFP enabled), we
should not break this for the MFP disabled case.
This patch fixes ieee80211_tx_h_select_key() not to drop management
frames if MFP is disabled. If MFP is enabled, Action frames will be
dropped before keys are set per IEEE 802.11w/D7.0. Other robust
management frames (i.e., Deauthentication and Disassociation frames)
are allowed unprotected prior to key configuration.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend CCMP to support encryption and decryption of unicast management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies hardware flags for powersave to support three different
flags:
* IEEE80211_HW_SUPPORTS_PS - indicates general PS support
* IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
* IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device
It also adds documentation for all this which explains how to set the
various flags.
Additionally, it fixes a few things:
* a spot where && was used to test flags
* enable CONF_PS only when associated again
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be needed for drivers that set the
IEEE80211_HW_NO_STACK_DYNAMIC_PS flag and still
want to handle dynamic PS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes an unnecessary assignment to info
in __ieee80211_tx() , tx.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a null data frame is generated from mac80211, it goes through
master_start_xmit and not through subif_start_xmit. Hence for the
power save timer to be triggered while sending this null data frame
also, the timer has to be reset from master_start_xmit.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After launching mesh discovery in tx path, reference count was not being
decremented. This was preventing module unload.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements dynamic power save for mac80211. Basically it
means enabling power save mode after an idle period. Implementing it
dynamically gives a good compromise of low power consumption and low
latency. Some hardware have support for this in firmware, but some
require the host to do it.
The dynamic power save is implemented by adding an timeout to
ieee80211_subif_start_xmit(). The timeout can be enabled from userspace
with Wireless Extensions. For example, the command below enables the
dynamic power save and sets the time timeout to 500 ms:
iwconfig wlan0 power timeout 500m
Power save now only works with devices which handle power save in firmware.
It's also disabled by default and the heuristics when and how to enable is
considered as a policy decision and will be left for the userspace to handle.
In case the firmware has support for this, drivers can disable this feature
with IEEE80211_HW_NO_STACK_DYNAMIC_PS.
Big thanks to Johannes Berg for the help with the design and code.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no driver that actually does fragmentation on the
device, and the callback is buggy (when it returns an error,
mac80211's fragmentation status is changed so reading the
frag threshold from userspace reads the new value despite
the error). Let's just remove it, if we really find some
hardware supporting it we can add it back later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unnecessary parameter in ieee80211_beacon_add_tim() and
removes unneeded definition and assignment for bdev (instance of net_device) in
ieee80211_beacon_get() and in ieee80211_get_buffered_bc()
(all in tx.c).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A warning would be printed for every packet that
is transmitted if the rate control information isn't
setup. Change this to WARN_ON_ONCE.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've come to think that not providing sequence numbers for
the normal STA mode case was a mistake, at least two drivers
now had to implement code they wouldn't otherwise need, and
I believe at76_usb and adm8211 might be broken.
This patch makes mac80211 assign a sequence number to all
those frames that need one except beacons. That means that
if a driver only implements modes that do not do beaconing
it need not worry about the sequence number.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also remove a few stray DECLARE_MAC_BUF that were no longer
used at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- This patch (against the linux-wireless-next git tree) removes a
redundant check in ieee80211_master_start_xmit (net/mac80211/tx.c)
and adjust indentation in this method accordingly.
In this method, there is no need to call again the
ieee80211_is_data() method; this is checked immediately before, in the
"if" command (we will not enter this block unless ieee80211_is_data()
is true, so that the "and" (&&) condition in that "if" command will be
fullfilled ).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes doubly defined variables in ieee80211_master_start_xmit
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.
There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.
Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mesh code doesn't support bridging mesh point interfaces
with wired ethernet or AP to construct an MPP or MAP. This patch adds
code to support the "6 address frame format packet" functionality to
mesh point interfaces. Now the mesh network can be used as backhaul
for end to end communication.
Signed-off-by: Li YanBo <dreamfly281@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to register the master netdev with cfg80211,
in fact, this is quite dangerous and lead to having to add
checks for the master interface all over the config handlers.
This patch removes the "ieee80211_ptr" from the master iface
in favour of having a small netdev_priv() associated with
the master interface that stores the ieee80211_local pointer.
Because of this, a lot of code in the configuration handlers
can go away. To make this patch easier to verify I have also
removed a number of wiphy_priv() calls in favour of getting
the sdata first and then the local pointer from that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
You can just pull up a monitor interface to get much more
detailed information, or, when debugging a driver, insert
dump code into the driver (which usually you will have to
do anyway to dump the driver-specific information). Hence
this option is useless.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon counters mac80211 keeps are only used for debugfs,
unfortunately, they are incorrect for many hardware designs,
namely any design that has a beacon template. Hence, remove the
counters so we don't create the impression they are usable.
This also allows removing the beacon MESH #ifdef again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, virtual interface pointers passed to drivers might be
from monitor interfaces and as such completely uninitialised
because we do not tell the driver about monitor interfaces when
those are created. Instead of passing them, we should therefore
indicate to the driver that there is no information; do that by
passing a NULL value and adjust drivers to cope with it.
As a result, some mac80211 API functions also need to cope with
a NULL vif pointer so drivers can still call them unconditionally.
Also, when injecting frames we really don't want to pass NULL all
the time, if we know we are the source address of a frame and have
a local interface for that address, we can to use that interface.
This also helps with processing the frame correctly for that
interface which will help the 802.11w implementation. It's not
entirely correct for VLANs or WDS interfaces because there the MAC
address isn't unique, but it's already a lot better than what we
do now.
Finally, when injecting without a matching local interface, don't
assign sequence numbers at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We cannot pass a VLAN vif pointer to the driver since those are
entirely virtual and we never tell the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_info->txrate_idx member isn't used by all RC algorithms
in the way it was intended to be used, move it into those that
require it (only PID) and keep track in the core code of which
rate was last used for reporting to userspace and the mesh MLME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need to know the basic rateset to be able to configure
the ACK/CTS programming in hardware correctly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some comments refer to 80211.o or similar; also remove
a comment about implementing fragments better, we really
have better things to do.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the scan functions are called ieee80211_sta_scan_*
or similar, make clean it up so they are all just called
ieee80211_scan_*.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits off mesh handling from the STA/IBSS.
Unfortunately it increases mesh code size a bit, but I
think it makes things clearer. The patch also reduces
per-interface run-time memory usage.
Also clean up a few places where ifdef is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.
It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.
If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.
This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the last users of the rx/tx_data->fc data members and use the
le16 frame_control from the header directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those functions that still use ieee80211_get_hdrlen are moved over
to use the little endian frame control.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we deal with mesh forwarding before the 802.11->802.3 conversion, thus
eliminating a few unnecessary steps. The next hop lookup is called from
ieee80211_master_start_xmit() instead of subif_start_xmit(). Until the next hop
is found, RA in the frame will be all zeroes for frames originating from the
device. For forwarded frames, RA will contain the TA of the received frame,
which will be necessary to send a path error if a next hop is not found.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make mac80211 transmit correctly fragmented packet after
queue was stopped
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In net/mac80211/tx.c, there are some #ifdef which checks
MAC80211_VERBOSE_PS_DEBUG
(which in fact is never set) instead of
CONFIG_MAC80211_VERBOSE_PS_DEBUG, as should be.
This patch replaces MAC80211_VERBOSE_PS_DEBUG with
CONFIG_MAC80211_VERBOSE_PS_DEBUG in these #ifdef commands in
net/mac80211/tx.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use dev_kfree_skb_any(); instead of dev_kfree_skb();, since
ieee80211_beacon_get function might be called from atomic.
(It's in a fail path.)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, almost every interface type has a 'bss' pointer
pointing to BSS information. This BSS information, however,
is for a _local_ BSS, not for the BSS we joined, so having
it on a STA mode interface makes little sense, but now they
have it pointing to the master device, which is an AP mode
virtual interface. However, except for some bitrate control
data, this pointer is only used in AP/VLAN modes (for power
saving stations.)
Overall, it is not necessary to even have the master netdev
be a valid virtual interface, and it doesn't have to be on
the list of interfaces either.
This patch changes the master netdev to be special, it now
- no longer is on the list of virtual interfaces, which
lets me remove a lot of tests for that
- no longer has sub_if_data attached, since that isn't used
Additionally, this patch changes some vlan/ap mode handling
that is related to these 'bss' pointers described above (but
in the VLAN case they actually make sense because there they
point to the AP they belong to); it also adds some debugging
code to IEEE80211_DEV_TO_SUB_IF to validate it is not called
on the master netdev any more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reworks the mac80211 debug settings making them more focused
and adding help text for those that didn't have one. It also removes a
number of printks that can be triggered remotely and add no value, e.g.
"too short deauthentication frame received - ignoring".
If somebody really needs to debug that they should just add a monitor
interface and look at the frames in wireshark.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the TX path to no longer use function pointers for
TX handlers but rather invoke them directly. If debugging is
enabled, mark the TX handlers noinline because otherwise they
all get inlined into invoke_tx_handlers() which makes it harder
to see where a bug is.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes warning: unused variable in invoke_tx_handlers
when compiling without MAC80211_DEBUG option
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes TX fragmentation caused by
tx handlers reordering and 'tx info to cb' patches
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies mac80211 to only have a single function calling the
TX handlers rather than them being invoked in multiple places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a driver rejects a frame in it's ->tx() callback, it must also
stop queues, otherwise mac80211 can go into a loop here. Detect this
situation and abort the loop after five retries, warning about the
driver bug.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 608961a5ec.
The problem is that the mac80211 stack not only needs to be able to
muck with the link-level headers, it also might need to mangle all of
the packet data if doing sw wireless encryption.
This fixes kernel bugzilla #10903. Thanks to Didier Raboud (for the
bugzilla report), Andrew Prince (for bisecting), Johannes Berg (for
bringing this bisection analysis to my attention), and Ilpo (for
trying to analyze this purely from the TCP side).
In 2.6.27 we can take another stab at this, by using something like
skb_cow_data() when the TX path of mac80211 ends up with a non-NULL
tx->key. The ESP protocol code in the IPSEC stack can be used as a
model for implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch denies the use of framentation while ampdu is used.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes doubly defined sband variable
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes unbalanced locking in ieee80211_get_buffered_bc
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 2e92e6f2c5 ("mac80211: use rate
index in TX control") I forgot to initialise a few new variables to -1 which
means that the rate control algorithm is never triggered and 0 is used as
the only rate index, effectively fixing the transmit bitrate at the lowest
supported.
This patch adds the missing initialisation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Bisected-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix bss not initialized in ieee80211_get_buffered_bc
and unbalanced locking
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cleans up the skb reallocation code to avoid problems with
skb->truesize, not resize an skb twice for a single output path
because we didn't expand it enough during the first copy and also
removes the code to further expand it during crypto operations
which will no longer be necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The useless channel use statistics are quite a lot of code, currently
use integer divisions in the packet fast path, are rather inaccurate
since they do not account for retries and finally nobody even cares.
Hence, remove them completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mac80211 and drivers to be multi-queue aware and
use that instead of the internal queue mapping. Also does a number
of cleanups in various pieces of the code that fall out and reduces
internal mac80211 state size.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no reason for a driver to reject a frame on
an A-MPDU queue when it can stop that queue for any period
of time and is given frames one by one. Hence, disallow it
with a big warning and reduce mac80211-internal state.
Also add a warning when we try to fragment a frame destined
for an A-MPDU queue and drop it, the actual bug needs to be
fixed elsewhere but I'm not exactly sure how to yet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The next patch will require that transmit handlers that are after
fragmentation are aware of the fact that the control info is also
fragmented. To make that easier, this patch moves a number of
transmit handlers before fragmentation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All interfaces should set the IEEE80211_TXPD_REQ_TX_STATUS flag for all TX frames
which will force the master interface to set the IEEE80211_TX_CTL_REQ_TX_STATUS
flag. This in turn will allow drivers to check for that flag before reporting
the TX status to mac80211.
This is very usefull when frames (like beacons, RTS and CTS-to-self) should not
be reported back to mac80211. Later we could add more extensive checks to
exclude more frames from being reported, or let mac80211 decide if it wants
the frame for status reporting or not.
v2: Monitor interfaces should also set IEEE80211_TXPD_REQ_TX_STATUS
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed earlier, we can unify locking in struct sta_info
and use just a single spinlock protecting all members of the
structure that need protection. Many don't, but one of the
especially bad ones is the 'flags' member that can currently
be clobbered when RX and TX is being processed on different
CPUs at the same time.
Because having four spinlocks for different, mostly exclusive
parts of a single structure is overkill, this patch also kills
the ampdu and mesh plink spinlocks and uses just a single one
for everything. Because none of the spinlocks are nested, this
is safe.
It remains to be seen whether or not we should make the sta
flags use atomic bit operations instead, for now though this
is a safe thing and using atomic operations instead will be
very simple using the new static inline functions this patch
introduces for accessing sta->flags.
Since spin_lock_bh() is used with this lock, there shouldn't
be any contention even if aggregation is enabled at around the
same time as both requires frame transmission/reception which
is in a bh context.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Tomas Winkler <tomasw@gmail.com>
Cc: Ron Rindjunsky <ron.rindjunsky@intel.com>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 only announce QoS/HT support when
the underlying hardware has four (or more) queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Ron Rindjunksi <ron.rindjunksi@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 should set the IEEE80211_TX_CTL_DO_NOT_ENCRYPT flag in tx_control
structure to inform drivers not to encrypt the beacon. Drivers that only check
for that flag before accessing the hw_key field, will otherwise cause a NULL
pointer dereference since that field is not configured for beacons.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames all mac80211 files (except ieee80211_i.h) to get rid
of the useless ieee80211_ prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is necessary for the upcoming Accesspoint patch for p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split it into ieee80211_tx_data and ieee80211_rx_data to clarify
usage/flag usage and remove the stupid union thing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various cleanups, reducing the #ifdef mess and other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the TX/RX paths in mac80211 to support mesh interfaces.
This code will be cleaned up later again before being enabled.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the code for TX filtered frames, splitting it out to
a new function to handle those cases, making the clear instruction
a flag and renaming a few things to be easier to understand and
less Atheros hardware specific. Finally, it also makes the comments
explain more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This consolidates all TIM handling code to avoid re-introducing
errors with the bitmap/set_tim order and to reduce code. While
reading the code I noticed a possible problem so I also added
a comment about that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM flag that is kept in each station's info is completely
useless, there's no code (aside from the debugfs display code)
checking it, hence it can be removed. While doing that, I noticed
that the TIM handling is broken when buffered frames expire, so
fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should be allowed to simply get a complete new beacon when
set_tim() is invoked (and set_tim() is required for drivers that
just want a beacon template!), so we need to update our own TIM
bitmap before calling set_tim() so that getting the beacon will
now get an already updated beacon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't really need to be a full int variable since it's
just a flag to indicate a PS-poll is in progress.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't really make sense to have extra pointers to the RX/TX
handler arrays instead of just using the arrays directly, that
also allows us to make them static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The _DROP result will need to be split in the RX path but not
in the TX path, so for preparation split up the type into two
types, one for RX and one for TX. Also make sure (via sparse)
that they cannot be confused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the 802.1X port acess control enable flag
since it is not required. Instead, set the authorized flag for
each station that we normally communicate with (WDS peers, IBSS
peers and APs we're associated to) and require hostapd to set
the authorized flag for all stations when port control is not
enabled.
Also, since I was working in that area, this documents station
flags and removes the unused "permanent" one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows qdisc support in A-MPDU Tx. a method to
handle QoS <-> TID switches is present in this patch.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reworking the port access control code, I forgot multicast frames
and those are now always rejected because the destination station is
not known. This changes the code to allow through multicast frames and
also avoid the sta hash lookup (which is bound to fail) for them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before calling update_beacon() mac80211 must
initialize the control.vif pointer so it can
be used by the driver to determine which
interface is trying to send the beacon.
v2: ieee80211_beacon_get() should also initialize the
vif pointer since it can be called by mac80211 internally
before calling config_interface().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the cfg80211 hooks for configuring beaconing
on an access point interface in mac80211. While doing so, it fixes
a number of races that could badly crash the machine when the
beacon is changed while being requested by the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this function returns != CONTINUE, it needs to put the
station struct it has acquired. Hence, having this unused
variable is not just superfluous but also misleading.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the decision making about whether a frame is encrypted
with a certain algorithm up into the TX handlers rather than having it
in the crypto algorithm implementation.
This fixes a problem with the radiotap injection code where injecting
a non-data packet and requesting encryption could end up asking the
driver to encrypt a packet without giving it a key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are various decisions influencing the decision whether to buffer
a frame for after the next DTIM beacon. The "do we have stations in PS
mode" condition cannot be tested by the driver so mac80211 has to do
that. To ease driver writing for hardware that can buffer frames until
after the next DTIM beacon, introduce a new txctl flag telling the
driver to buffer a specific frame.
While at it, restructure and comment the code for multicast buffering
and remove spurious "inline" directives.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch left only one user of the ieee80211_is_eapol()
function and that user can be eliminated easily by introducing
a new "frame is EAPOL" flag to handle the frame specially (we
already have this information) instead of doing the (expensive)
ieee80211_is_eapol() all the time.
Also, allow unencrypted frames to be sent when they are injected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Kosina