Orange Pi 3 board requires enabling a voltage shifting circuit via GPIO
for the DDC bus to be usable.
Add support for hdmi-connector node's optional ddc-en-gpios property to
support this use case.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806155744.10263-4-megous@megous.com
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Some boards have HDMI VCC pin connected to voltage regulator which may
not be turned on by default.
Add support for such boards by adding voltage regulator handling code to
HDMI driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Icenowy: change supply name to "hvcc"]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-11-icenowy@aosc.io
DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net
While A83T HDMI PHY seems to be just customized Synopsys HDMI PHY, H3
HDMI PHY is completely custom PHY.
However, they still have many things in common like clock and reset
setup, setting sync polarity and more.
Add support for H3 HDMI PHY variant.
While documentation exists for this PHY variant, it doesn't go in great
details. Because of that, almost all settings are copied from BSP linux
4.4. Interestingly, those settings are slightly different to those found
in a older BSP with Linux 3.4. For now, no user visible difference was
found between them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-13-jernej.skrabec@siol.net
There are multiple variants of DW HDMI PHYs in Allwinner SoCs. While
some things like clock and reset setup are the same, PHY configuration
differs a lot.
Split out code which is PHY specific to separate functions and create
a structure which holds pointers to those functions.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180301213442.16677-11-jernej.skrabec@siol.net
A83T has DW HDMI IP block with a custom PHY similar to Synopsys gen2
HDMI PHY.
Only video output was tested, while HW also supports audio and CEC.
Support for them will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-11-jernej.skrabec@siol.net
Ondrej Jirman