After a bus reset, we should move our state to
Default, in order to be able to re-enumerate again.
I only managed to trigger this problem with g_ether
by removing the cable after a few transfers had been
completed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
All our revision macros are defined with the entire
32-bits which we read from GSNPSID register, so we
must cache all 32-bits properly rather than masking
the top 16-bits.
This will fix all revision checks we have on current
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a very small possibility (previously unimagined
by us) that the whole Mass Storage delayed status happens
rather early, before we even get our XferNotReady event.
In that case, we will be queueing a request to ep0 while
we're still on Setup Phase and we would be waiting for
another usb_ep_queue() forever.
Handle such cases by clearing dwc->delayed_status so that
we start control status from the next XferNotReady like
there was no wait for Delayed Status.
Tested against Linux 3.2-rc3 and USB30CV tool from USB-IF
(on a Windows XP with USB3 PCIe card).
Signed-off-by: Felipe Balbi <balbi@ti.com>
ep->max_streams is a mere hint to the gadget
driver that 'ep' supports stream handling. Using
that as a decision variable for enabling streams
was my worst brain-fart to date.
Instead, we should check from the Superspeed
Endpoint Companion Descriptor if the endpoint
has requested streams. For that we need a little
re-factoring but it is now correct.
Debugged-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
previous commit fixed part of it but it was still
calling usb_ep_queue() from IRQ context without
loosing locks. That cannot be done otherwise we will
have a recursive locking.
Also, we need to assign the 'dep' pointer on
dwc->ep0_usb_req otherwise we will have a NULL
pointer dereference on dwc3_map_buffer_to_dma().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of special functions and shortcuts for sending our internal
answers to the host we started doing what the gadget does and used the
public API for this. Since we only were using a few fields the
usb_request was enough. Later added the list handling in order to
synchronize the host / gadget events and now we require to have the
dwc3_request struct around our usb_request or else we touch memory that
does not belong to us. So this patch does this.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We mask the correct bits within the wrong register. The power
optimization mode is stored hwparam1 register and not in hwparam0.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the new module_platform_driver macro is a helper
for modules which just register and unregister the
platform_driver. It allows us to delete a few
duplicated lines.
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 revisions <1.88a have an issue which would
case a missing Disconnect event if cable is
disconnected while there's a Setup packet
pending the FIFO.
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 revisions <1.90a have an issue which would cause
a missing USB3 Reset event. In such cases, it's
suggested that we follow the steps of a normal
USB3 Reset on Connection Done Event.
Signed-off-by: Felipe Balbi <balbi@ti.com>
RTL revisions <1.83a have an issue where, depending
on the link partner, the USB link might do multiple
entry/exit of low power states before a transfer
takes place causing degraded throughput.
The suggested workaround is to clear bits
12:9 of DCTL register if we see a transition
from U1|U2 to U0 and only re-enable that on
a transfer complete IRQ and we have no pending
transfers on any of the enabled endpoints.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch avoids the compiler spitting out the following warning:
|drivers/usb/dwc3/gadget.c:1304: warning: 'trb' is used uninitialized \
in this function
This is only uninitialized if the list of to-cleanup TRBs is empty which
should not be the case because we call this functions once a transfer
completed so it should be on list.
In order to make the warning disappear we return early. This should
never happen and the WARN_ON_ONCE(1) is there in case it happens
so we can investigate what went wrong.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the re-worked ep0 handling (which uses HW's hints to recognize the ep0
status) we lost the delayed status handling. This is used by the file and mass
storage gadget to gain some extra time so setup its internal status before it
can proceed further requests.
In particular the storage gadget does nothing on USB_REQ_SET_CONFIGURATION but
wakes up a thread which handles the request. If the udc driver continues ep0
handling before the thread did its work then then endpoint is not yet
configured and further requests will fail. Once the gadget is ready, it will
enqueue an empty packet which is used for synchronization.
In order to fix this issue, the patch does the following:
Set ->delayed_status once the delayed_status has been notices and do not
continue on the next XferNotReady event. We will continues ep0 processing once
the gadget enqueued the zero packet for synchronization.
A cleaner approach would be to enforce the gadget to enqueue an empty
(zero) request even for the status phase but this would do for now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We wait for the XferNotReady before we start the transfer and by then we
know ep0 state in which we supposed to be.
This is some cleanup work for the following patch in which we require to
know the ep0 state before the transfer completes.
While here, also change the argument to dwc3_ep0_do_control_status() so
we don't require the complete event structure but only the required
piece of information.
Inspired-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse caught three mistakes on this driver,
fix them:
drivers/usb/dwc3/ep0.c:806:29: warning: duplicate const
drivers/usb/dwc3/debugfs.c:481:15: warning: symbol 'dwc3_debugfs_init' \
was not declared. Should it be static?
drivers/usb/dwc3/debugfs.c:518:16: warning: symbol 'dwc3_debugfs_exit' \
was not declared. Should it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were a few coding style issues with this driver
which are now fixed:
drivers/usb/dwc3/debugfs.c:48: WARNING: Use #include \
<linux/uaccess.h> instead of <asm/uaccess.h>
drivers/usb/dwc3/debugfs.c:484: ERROR: space required \
before the open brace '{'
drivers/usb/dwc3/ep0.c:261: WARNING: line over 80 characters
drivers/usb/dwc3/ep0.c:287: WARNING: suspect code indent \
for conditional statements (16, 23)
drivers/usb/dwc3/gadget.c:749: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.c:1267: WARNING: line over 80 characters
drivers/usb/dwc3/gadget.h:116: WARNING: line over 80 characters
drivers/usb/dwc3/io.h:42: WARNING: Use #include \
<linux/io.h> instead of <asm/io.h>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A few inits like the scale value or the removal of the DISSCRAMBLE is
done in the gadget code however it touches a general register.
Move this piece to the core.c file since it is likely to be requied by
both, parts of the core (device and host).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are two where need to set operational mode:
- during initialization while we decide to run in host,device or DRD
mode
- at runtime via the debugfs interface.
This patch provides a new function which sets the operational mode and
moves its initialiation to the mode switch instead in the gadget code
itself.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In "usb: dwc3: remove special status request handling in ep0" I simplied
a few things and used the generic API for the status transfers. The bug
I introcuded here is that we queue now requests to dep[1] but we don't
clear that list in the stall+start case.
Actually we don't need to use dep[1] at all. We only did in the past to
talk to the correct endpoint (i.e. in or out). This is now take care of
in a diffent place within the ep0 code. So we could queue the in
transfers to dep[0] and don't use dep[1] at all.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first access was correct, the second was wrong.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
hardware will tell us how many event buffers we
need to support, so let's allocate the array
dynamically too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we ever have an omap with multiple instances of
the DWC3 IP, we need unique names for them. In order
to achieve that, let's use the dwc3_get/put_device_id()
calls to give us an unique device identifier.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we want to support situations where we have
both SoC and PCIe versions of the IP on the same
platform, we need to have sequential numbers between
them, otherwise we will still have name collisions.
Because of that, we need to move dwc3_get/put_device_id()
to core.c and export that symbol to be used by glue
layers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The GetStatus (STD)-request is handled the driver and uses a tiny hack
to send the two bytes long answer. This patch removes the custom hack
uses the normal usb_ep_queue() for that.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we stall and restart we have to reset also this flag to 0 as there is
nothing pending anymore.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The read and write operation is atomic and we need no locking around
this operations. What we need however is a lock that is held which
ensures that the content of the DWC3_GCTL has not been changed. With
this, the conten may have been change changed after the first but before
our write back.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can have three modules here: dwc3.ko, dwc3-omap.ko and dwc3-pci.ko.
The later have already ids-aliases for probing and is fine. The omap
module has alias for DT but lacks alias for the "native"
platform_device. Maybe we should get rid of it and stick to the DT name?
Both glue modules create a new device for which the dwc3.ko module is
responsible and that one lacks the platform alias.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sometimes the host might be trying to initiate Data or
Status phase for an older Control transfer. In such
situations we must STALL that transfer and restart
the state machine rather than letting such situation
go through the wire.
Signed-off-by: Felipe Balbi <balbi@ti.com>
I have talked to USB-IF about USB30CV issuing SetAddres()
with a device on Configured state and they have agreed on
changing USB30CV not to do so.
Adding back the STALL reply in such case and while at
that, also add a debugging message for an address which
is too large.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Designware USB3 IP can be configured with
an internal xHCI. If we're running on such a
version, let's start the xHCI stack.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no need to add driver_data for something
we can fetch from HW.
This also makes our id_table unnecessary - at least
for now -, so we also remove it on the same patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this is mainly for testing. In order to be able
to test if we're enumerating correctly on all
speeds, let that be controlled by a module
parameter.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit replaces usb_gadget's is_dualspeed field with
a max_speed field.
[ balbi@ti.com : Fixed DWC3 driver ]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts the drivers in drivers/usb/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The previous patch left an unused variable, I apologize.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This a use example of the regs32 utilities in debugfs, although
this fuse use ":" as separator between name and value, and debugs
uses "=" (as it looked to me a more common practice).
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this the gadget will never be able to allocate a stream capable
endpoint. The manual says that the stream id is a 16bit id. It does not
talk about an upper limit in any other way. So I think 15 is a
reasonable limit :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These files uses the full set of MODULE_ macros and so need to
include module.h directly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
our parameter structures need to be written to
HW, so instead of assuming little endian, we
convert those into bit shifts.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The dwc3 core has internal clock gating support.
Let's allow that to happen by clearing the disable
bit in GCTL register.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cache the contents of GHWPARAMS* registers in
our device structure for easy access.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
That structure will hold a copy of readonly
GHWPARAMS* registers for ease accessing by
the driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch adds support for streams
to dwc3 driver.
While at that, also fix one small issue on
endpoint disable where we should clear all
flags not only ENABLED.
Reviewied-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We already have the value from gadget drivers,
just need to pass it to our controller.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes DWC3_EP_WEDGE do the right thing, which is
prevent DWC3_EP_WEDGE from ever being cleared by a
ClearFeature(HALT) command.
[ balbi@ti.com : allowed set_wedge to send SetHalt command
to controller ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An older version of the databook said to wait for the FIFO to
drain, but that has been removed from the newer databooks.
Waiting for RxFIFO to drain caused problems when testing against
one of the host controllers available in the market.
After talking to one of the RTL engineers, he stated that we
should _not_ wait for RxFIFO to drain.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DEPSTARTCFG for non-EP0 EPs must only be sent once per config
[ balbi@ti.com : changed config_start to start_config_issued ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use "ep0in" and "ep0out" instead "ep1in" and "ep0out" which is confusing
and not consistent with the remaining output.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We already give requests back in dwc3_ep0_stall_and_restart() so
doing it again here will most likely corrupt the list.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The way it was before was really meaningless.
Now it looks saner.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need to care about direction on a two stage
transfer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to USB 3.0 Specification, a SetAddress()
while device is in Configured State has an unspecified
behavior (see Section 9.4.6). Still USB30CV wasn't
happy with my Stall reply.
To make that thing happy, just accept the SetAddress()
always. No problems have been observed thus far.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's useful to know which states core is going
through, as it might help us figure out misbehavior
on specific link states.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag will tell us which direction we're
expecting on the next (data or status) phase.
It will help us catching errors of host going
crazy and requesting data of the wrong direction.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if req->dma isn't DMA_ADDR_INVALID it means gadget driver
mapped the request or allocated from coherent, so it's
unnecessary to do anything.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the gadget drivers sends a ZLP we are trying to map this this request
which does not work on all implementations. So we simply skip mapping
it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3-wrapper can be used by any other wrapper,
using dwc3-omap makes it clear that we're running
on OMAP SoC.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The OMAP wrapper allows us to either control internal
OTG signals via SW or HW. Different boards might wish
to use one or the other mode of operation. Let's have
have that information passed via platform_data for now.
After DT conversion is finished for OMAP, we can easily
convert this to a DT attribute.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to have actual HW in order to implement
and test that part of the code anyway. Until then
it's best to remove it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this field will hold the next expected event.
In certain cases, host might fall into some error
condition and ask from us the wrong Control phase.
On such situations, we should stall and restart.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever we issue a Set Stall command on EP0,
the state machine will be restarted and Stall
is cleared automatically, when core receives
the next SETUP packet.
There's no need to track that EP0_STALL state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when we're going to issue Set Stall command,
we should clear DWC3_EP_STALL flag, but also
we should clear BUSY, HALTED and all others.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are two spots where we wait until the HW finishes processing a
certain command. Initially we had a few problems and we used 500ms as a
limit to be on a the safe side. Paul Zimmerman mentioned this is little too
much. After a debugging session, we noticed that we hardly ever go over 20us
and didn't pass 30usec so far. Using mdelay() seems way overloaded.
Giving the current numbers 500usec as the upper limit is more than enough.
Should it ever timeout then something is definitely wrong.
While here, also replace the type with u32 since long does not really
fit here.
Cc: Paul Zimmerman <paul.zimmerman@synopsys.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- since a while we are disabling an endpoint and purging every requests on
RESET and DISCONNECT which leads to a warning since the endpoint was
disabled twice (once by the UDC, and second time by the gadget). I
think UDC should nuke all requests because all those requests
become invalid. It's gadget driver's responsability, though, to disable
its used endpoints. This is done by merging dwc3_stop_active_transfer()
and dwc3_gadget_nuke_reqs() into dwc3_remove_requests().
- dwc3_stop_active_transfer() is now no longer called unconditionaly.
This has the advantage that it is always called to disable an active
transfer which means if res_trans_idx 0 than something went wrong and
it is an error condition because we can't clean up the requests.
- Remove the DWC3_EP_WILL_SHUTDOWN which was introduced while
introducing the command complete part for dequeue. All requests on
req_queued list should be removed during the dwc3_cleanup_done_reqs()
callback so there is no reason to go through the list again.
We consider it an error condition if requests are still on this
list since we never queue TRB without LST=1 (the last requests has
always LST=1, there are no requests with LST=0 behind it).
[ balbi@ti.com : reworked commit log a bit, made patch apply ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We read the DWC3_GSNPSID register to make sure we got the correct
register offset passed. One of the recent commits moved the soft reset
before this so in case of the wrong offset we end up with "reset timed
out". This patch moves the "id" check before the reset again.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some issues around for enabling/disabling this mode and
handling it. It does not work perfectly (yet). However we have a few
gadgets tested successfuly so far. That means we are quite confident
that we won't need this in near future.
So I'm for removing it and bringing a working version back once there is
a need for it.
Thanks to Dan Carpenter who spotted the wrong memory handling here.
[ balbi@ti.com : made it actually apply ]
Cc: Dan Carpenter <error27@gmail.com>
Cc: wharms@bfs.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The DesignWare USB3 core tells us which phase
of a control transfer should be started, it
also tells us which physical endpoint needs
that transfer.
With these two informations, we have all we
need to simply EP0 handling quite a lot and
get rid rid of the SW state machine tracking
ep0 states.
For achieving this perfectly, we needed to
add support for situations where we get
XferNotReady while endpoint is still busy
and XferNotReady while gadget driver still
hasn't queued a request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we have transfers which aren't aligned
to wMaxPacketSize, we need to be careful with
how we start the transfer with the HW. OUT
transfers _must_ be aligned with wMaxPacketSize
and in order to guarantee that, we use a bounce
buffer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This core cannot handle OUT transfers which aren't
aligned to wMaxPacketSize, but that can happen at
least on control endpoint with the USB Audio Class.
This patch adds a bounce buffer to be used on the
case of a non-aligned ep0out request is queued.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The status field of the Transfer Not Read event
is different on Control Endpoints. On this patch
we are just adding the defines to be used on a
later patch which will re-work the control endpoint
handling.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the previous message had too little meaning. Make
it more human readable and use the macro we already
had for extracting the command completion status out
of DEPCMDn register.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we don't set DMA address to invalid when unmapping,
we might fall in a situation where request buffer
can't be mapped to DMA again.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We may as well fix this potential leak so we don't have to listen to
the static checkers complain.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi