When we had a connection for WoWLAN and after resume it
needed to be disconnected, the previous commit enabled
sending a deauth frame to the AP. This frame would not
go through on MFP-enabled networks as the key for it is
marked tainted before the frame is transmitted.
Allow a tainted key to be used for deauth frames. Worst
case, we'll use a wrong key because the PTK was rekeyed
while suspended, but more likely the PTK is still fine
and the taint flag really only applies to the GTK(s).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
gcc cannot prove that the value of sdata->vif.type does not
change between the switch() statement and the second
comparison to NL80211_IFTYPE_AP, causing a harmless
warning.
Slightly reordering the code makes the warning go away
with no functional change.
Without this patch, building ARM at91sam9g45_defconfig with
gcc-4.6 results in:
net/mac80211/tx.c: In function 'ieee80211_subif_start_xmit':
net/mac80211/tx.c:1797:22: warning: 'chanctx_conf' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This functions will be used for mesh beacons, too.
Signed-off-by: Marco Porsch <marco@cozybit.com>
[some formatting fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel contexts are not always used with monitor interfaces. If no channel
context is set, use the oper channel, otherwise tx fails.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[check local->use_chanctx]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes more wifi status skb leaks, leading to hostapd/wpa_supplicant hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One error path in ieee80211_subif_start_xmit() will
double-free the SKB. Set it to NULL to prevent that.
This issue was introduced by my channel context
changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:
+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+ ps = &sdata->u.mesh.ps;
Some references to the AP's beacon structure are removed where they
were obviously not used.
The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places free skbs using dev_kfree_skb even though they're called
after ieee80211_subif_start_xmit might have cloned it for tracking tx
status. Use ieee80211_free_txskb here to prevent skb leaks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.
Conflicts:
drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The destination address of unicast frames forwarded through a mesh gate
was being replaced with the broadcast address. Instead leave the
original destination address as the mesh DA. If the nexthop address is
not in the mpath table it will be resolved. If that fails, the frame
will be forwarded to known mesh gates.
Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.
[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we only need the band, remove the channel
pointer from struct ieee80211_tx_data and also
assign it properly, depending on context, to the
correct operating or current channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.
Add the appropriate parameters to respect the difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When drop_unencrypted is enabled and MFP is disabled,
non-robust management frames for not-yet associated STA are dropped.
This isn't visible as many management frames sent from the kernel
have TX_INTFL_DONT_ENCRYPT set and management frames injected
from a monitor vif have TX_CTL_INJECTED so aren't dropped.
But management frames sent from userspace via NL80211_CMD_FRAME
do not have this flag set, so are dropped.
This patch make it always accept non-robust management frames.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "no key" case in key selection that decides
whether to drop the frame or not is impossible
to understand, restructure the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[cavallar@lri.fr: removed blank line and restructured action frame clause]
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
This patch fixes the problem of unreachable mesh STA from
Distribution System (DS) due to the introduction of previous
patch solving the mesh STA joining from one MBSS to another
MBSS.
Reported-by: Georgiewskiy Yuriy <bottleman@icf.org.ru>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee802_1d_to_ac is defined as a const int[8],
but the tid parameter has a range from 0 to 15.
Cc: stable@vger.kernel.org
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_TX_MAX_RATES can be reduced from 5 to 4 as there
is no current hardware supporting a rate chain with 5 multi
rate stages (mrr), so 4 mrr stages are sufficient.
The memory that is freed within the ieee80211_tx_info struct
will be used in the upcoming Transmission Power Control (TPC)
implementation.
Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The implementation of tx_frags is buggy due to
not handling queue stop, and there's no driver
implementing it so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.
Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This and ieee80211_add_ext_srates_ie() aren't
exported, so can't be used by drivers anyway,
but there's also no reason that they should be
so make them private to mac80211 and use sdata
instead of vif arguments.
Acked-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh station that joins an MBSS is reachable using mesh portal with 6
address frame by mesh stations from another MBSS if these two different
MBSSes are bridged. However, if the mesh station later moves into the
same MBSS of those mesh stations, it is unreachable by mesh stations
in the MBSS due to the mpp_paths table is not deleted. A quick fix
is to perform mesh_path_lookup, if it is available for the target
destination, mpp_path_lookup is not performed. When the mesh station
moves back to its original MBSS, the mesh_paths will be deleted once
expired. So, it will be reachable using mpp_path_lookup again.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used to test for BSS multicast receivers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removes hw.conf.channel usage from the following functions:
* ieee80211_mandatory_rates
* ieee80211_sta_get_rates
* ieee80211_frame_duration
* ieee80211_rts_duration
* ieee80211_ctstoself_duration
This is in preparation for multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 currently only supports one hardware queue
per AC. This is already problematic for off-channel
uses since if we go off channel while the BE queue
is full and then try to send an off-channel frame
the frame will never go out. This will become worse
when we support multi-channel since then a queue on
one channel might be full, but we have to stop the
software queue for all channels. That is obviously
not desirable.
To address this problem allow drivers to register
more hardware queues, and allow them to map them to
virtual interfaces. When they stop a hardware queue
the corresponding AC software queues on the correct
interfaces will be stopped as well. Additionally,
there's an off-channel queue to solve that problem
and a per-interface after-DTIM beacon queue. This
allows drivers to manage software queues closer to
how the hardware works.
Currently, there's a limit of 16 hardware queues.
This may or may not be sufficient, we can adjust it
as needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.
So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates are added with supported rates IE and extended supported
rates IE.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds MBSS extensible synchronization framework (Sec.
13.13.2 of IEEE Std. 802.11-2012).
The framework is implemented via an ops table which defines the
following functions:
rx_bcn_presp() - this is called every time a mesh beacon is
received.
adjust_tbtt() - this is called immediately before a beacon is about
to be transmitted.
The default neighbor offset synchronization defined in the standard is
implemented. We also provide template functions for vendor specific
methods.
When neighbor offset synchronization is active (which is the default)
mesh neighbors in the same MBSS will track timing offsets to each other
and compensate clock drift.
In our tests we observed that this mesh synchronization implementation
successfully corrected drifts between stations of ~2PPM while
introducing a jitter of ~20us.
It is also possible to test this framework on mac80211_hwsim simulated
phys to see how it behaves under different topologies, over poor links,
etc.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While associated we should never have empty SSID, but life can be full
of surprises, and is allways better to print a warning than crash.
Before memcpy() in ieee80211_probereq_get() check ssid_len instead of
ssid pointer, sice pointer it always passed by "ssidie + 2" expression
to send probe functions, so practically never can be NULL.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the code formatting and also replace
the constant 0 by IEEE80211_AC_VO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bad indentation & pointless if nesting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling mod_timer from the rx/tx hotpath is somewhat expensive, and the
timeout doesn't need to be so precise.
Switch to a different strategy: Schedule the timer initially, store jiffies
of all last rx/tx activity which would previously modify the timer, and
let the timer re-arm itself after checking the last rx/tx timestamp.
Make the session timers deferrable to avoid causing extra wakeups on systems
running on battery.
This visibly reduces CPU load under high network load on small embedded
systems.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since some of the HT code pre-dates 802.11n-2009
some names are wrong. The one that bothers me most
is that "HT operation" is called "HT information"
in our code and that causes confusion.
Rename "HT information" to "HT operation" and also
the control_chan field to primary_chan to match
the name used in the spec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uapsd_queues and uapsd_max_sp_len are relevant only for managed
interfaces, and can be configured differently for each vif.
Move them from the local struct to sdata->u.mgd, and update
the debugfs functions accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While setting up or tearing down a BA session mac80211 is buffering
pending frames for the according TID. However, there's currently no
limit on how many frames are buffered possibly leading to an out-of-
memory situation. This can happen on systems with little memory when
the CPU is fully loaded since the BA session work is executed in
process context while frames can still come via softirq.
Apply a limitation to the TIDs pending queue to avoid consuming
too much memory in this situation.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This renames the IEEE80211_TX_CTL_POLL_RESPONSE
TX flag to IEEE80211_TX_CTL_NO_PS_BUFFER and also
uses it for non-bufferable MMPDUs (all MMPDUs but
deauth, disassoc and action frames.)
Previously, mac80211 would let the MMPDU through
but not set the flag so drivers supporting some
hardware aids for avoiding the PS races would
then reject the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That's a lot longer than open-coding it and
doesn't really add value, so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In function ieee80211_tx_h_encrypt the var info was
initialized from tx->skb, since the fucntion
is called after the function ieee80211_tx_h_fragment
tx->skb is not valid anymore.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently BAR, ADDBA and DELBA frames are always sent using AC_VO. If
the TID for which a BA session is established is assigned to a different
queue BAR, ADDBA and DELBA frames can "overtake" frames of the according
BA session.
Hence, always put BA session related frames into the same queue as the
BA sessions data frames.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that IBSS no longer needs to insert stations
from atomic context, we can get rid of all the
special cases for that, and even get rid of the
sta_lock (though it needs to stay as tim_lock.)
This makes the station management code much more
straight-forward.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, each AP interface will send multicast
traffic if any interface has a station entry even
if that station entry is allocated only. With the
new station state management we can easily fix it
by adding a counter that counts each authorized
station only and send multicast traffic only when
the correct interface has at least one authorized
station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station entries can have various states, the most
important ones being auth, assoc and authorized.
This patch prepares us for telling the driver about
these states, we don't want to confuse drivers with
strange transitions, so with this we enforce that
they move in the right order between them (back and
forth); some transitions might happen before the
driver even knows about the station, but at least
runtime transitions will be ordered correctly.
As a consequence, IBSS and MESH stations will now
have the ASSOC flag set (so they can transition to
AUTHORIZED), and we can get rid of a special case
in TX processing.
When freeing a station, unwind the state so that
other parts of the code (or drivers later) can rely
on the transitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes another regression from my "pass all
fragments to driver at once" patches -- if the
packet is being retransmitted then we don't go
through all handlers, but we still need to move
it to the skbs list, otherwise we run into the
first warning in __ieee80211_tx() and leak the
skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to initiate a path discovery when receiving a frame for which
there is no forwarding information. To cut down on PREQ spam, just send
a (gated) PERR in response.
Also separate path discovery logic from nexthop querying. This patch
means we no longer queue frames when forwarding, so kill the PERR TX
stuff in discard_frame().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't have any actual effect here, but we should
skb_put() *before* copying the data.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel reported that my previous patches to enable
handing all fragments to drivers at once triggered
the warning that the SKB queue wasn't empty. This is
happening when we actually queue up some frames and
don't hand them to the driver (queues are stopped).
The reason for it is that my code that splices the
frame(s) over to the pending queue didn't re-init
the local queue, so skb_queue_empty() was false. Fix
this by using the _init versions of the splicing.
Also, convert the warning to WARN_ON_ONCE.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently tx aggregation is not being timed out even if timeout is
specified when aggregation is opened. Tx tid stays active until delba
arrives from recipient (i.e. recipient times out tid when it is
inactive).
The problem with this approach is that delba can get lost in the air
and tx tid will stay perpetually opened on the originator while closed
on recipient thus all data sent via this tid will be lost.
This patch implements tx tid timeouting in way very similar to rx tid
timeouting.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature has been superseded by the NoAck per Queue feature.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers can usually handle fragmented packets
much easier when they get the entire list of
fragments at once. The only thing they need to
do is keep enough space on the queues for up
to ten fragments of a single MSDU.
This allows them to implement this with a new
operation tx_frags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This just prepares for passing the entire fragment
list to the driver. No significant changes, but the
TX throughput is calculated slightly differently
now and we blink only once for each MSDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of adjusting the fragment flags at
TX time, adjust them at fragmentation time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are currently linking the skbs by using skb->next
directly. This works, but the preferred way is to use
a struct sk_buff_head instead. That also prepares for
passing that to drivers directly.
While at it I noticed we calculate the duration for
fragments twice -- remove one of them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The shared key authentication frame that needs to be
encrypted (the third one in the shared key handshake)
is directly encrypted in ieee80211_send_auth and the
IEEE80211_TX_INTFL_DONT_ENCRYPT is set. All others
are not encrypted, so the only way to get to this is
erroneously on no-monitor AP side.
Remove the special case for authentication frames to
fix the AP shared key side when operating without
cooked monitor interfaces -- with cooked monitor the
IEEE80211_TX_INTFL_DONT_ENCRYPT also gets set, so we
never get here -- an AP never encrypts auth frames.
Without this patch, an AP operating in WEP mode with
my no-monitor patches would erroneously encrypt all
authentication frames, instead of none.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting a probe response template for an interface operating in
AP mode. Low level drivers are notified about changes in the probe
response template and are able to retrieve a copy of the current probe
response. This data can, for example, be uploaded to hardware as a
template.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the socket wifi TX status error
queue reflection in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Ashok Nagarajan <anagar6@uic.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove most references to magic numbers, save a few bytes and hopefully
improve readability.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reformat the check, the indentation is completely strange.
Also change the last part of the condition to make the
code shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was another workaround for truesize "bugs".
The reason we did this was that when we orphaned
the SKB it wouldn't be truesize-checked later.
Now that the check is gone (and we just charge
the former smaller size to the socket) there's
no longer a reason to orphan the skb here.
Keep the skb charged to the socket until it is
really freed (or orphaned in TX status). This
helps flow control and allows us to get at the
socket later for other purposes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to adjust truesize.
The history of this was that we always ran into
skb_truesize_bug (via skb_truesize_check) which
has since been removed in commit 92a0acce18.
skb_truesize_check() checked that truesize was
bigger or equal to the actual allocation, which
would trigger in mac80211 due to header adding.
The check no longer exists and we shouldn't be
messing with the truesize anwyay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can now move the radiotap header parsing into
ieee80211_monitor_start_xmit(). This moves it out of
the hotpath, and also helps the code since now the
radiotap header will no longer be present in
ieee80211_xmit() etc. which is easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The purpose of this is two-fold:
1) by moving it out of tx_data.flags, we can in
another patch move the radiotap parsing so it
no longer is in the hotpath
2) if a device implements fragmentation but can
optionally skip it, the radiotap request for
not doing fragmentation may be honoured
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the only way the interface can be a monitor
interface in ieee80211_xmit() is because the frame
came from ieee80211_monitor_start_xmit() we can
move all the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow injected unicast frames to be sent without having to wait
for an ACK.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11 says:
"Sequence numbers for QoS (+)Null frames may be
set to any value."
However, if we use the normal counters then peers
will get confused with aggregation since there'll
be holes in the sequence number sequence.
To avoid that, neither assign a sequence number
to QoS null frames nor put them on aggregation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PS-poll, there's a possible race between
us expiring a frame and the station polling
for it -- send it a null frame in that case.
For uAPSD, the standard says that we have to
send a frame in each SP, so send null if we
don't have any other frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.
Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For uAPSD support we'll need to have per-AC PS
buffers. As this is a major undertaking, split
the buffers before really adding support for
uAPSD. This already makes some reference to the
uapsd_queues variable, but for now that will
never be non-zero.
Since book-keeping is complicated, also change
the logic for keeping a maximum of frames only
and allow 64 frames per AC (up from 128 for a
station).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the TIM bit for a given station is set
and cleared all over the place. Since the logic to
set/clear it will become much more complex when we
add uAPSD support, as a first step let's collect
the entire logic in one place. This requires a few
small adjustments to other places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the
presence of the mesh control header in their QoS header.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support QoS in mesh, we need to assign queue mapping only
after the next hop has been resolved, both for forwarded and locally
originated frames. Also, now that this is fixed, remove the XXX comment
in ieee80211_select_queue().
Also, V-Shy Ho reported that the queue mapping was not being applied to
the forwarded frame (fwd_skb instead of skb). Fixed that as well.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When this flag is set, Tx A-MPDU sessions will not be started by
mac80211. This flag is required for devices that support Tx A-MPDU setup
in hardware.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct ordering of IEs in the mesh beacon while removing unneeded IEs
from mesh peering frames. Set privacy bit in capability info if security
is enabled. Add utility functions to aid in construction
of IEs and reduce code duplication.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (ath9k for example) are using skb->protocol to treat EAPOL
frames somehow special (disallow aggregation for example).
When running in AP mode hostapd injects the EAPOL frames through a
monitor interface and thus skb->protocol isn't set at all. Hence, if the
injected frame is a data frame and carries a rfc1042 headaer update the
skb->protocol field accordingly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In WoWLAN, devices may use crypto keys for TX/RX
and could also implement GTK rekeying. If the
driver isn't able to retrieve replay counters and
similar information from the device upon resume,
or if the device isn't responsive due to platform
issues, it isn't safe to keep the connection up
as GTK rekey messages from during the sleep time
could be replayed against it.
The only protection against that is disconnecting
from the AP. Modifying mac80211 to do that while
it is resuming would be very complex and invasive
in the case that the driver requires a reconfig,
so do it after it has resumed completely. In that
case, however, packets might be replayed since it
can then only happen after TX/RX are up again, so
mark keys for interfaces that need to disconnect
as "tainted" and drop all packets that are sent
or received with those keys.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on inputs from Johannes Berg <johannes@sipsolutions.net>
from http://article.gmane.org/gmane.linux.kernel.wireless.general/68193
and http://article.gmane.org/gmane.linux.kernel.wireless.general/71702
In xmit path, devices that do full hardware crypto (including
MMIC and ICV) need no tailroom. For such devices, tailroom
reservation can be skipped if all the keys are programmed into
the hardware (i.e software crypto is not used for any of the
keys) and none of the keys wants software to generate Michael
MIC and IV.
v2: Added check for IV along with MMIC.
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Tested-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Cc: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
v3: Fixing races to avoid WARNING: at net/mac80211/wpa.c:397
ccmp_encrypt_skb+0xc4/0x1f0
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
v4: Added links with message ID
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds sparse RCU annotations to most of
mac80211, only the mesh code remains to be
done.
Due the the previous patches, the annotations
are pretty simple. The only thing that this
actually changes is removing the RCU usage of
key->sta in debugfs since this pointer isn't
actually an RCU-managed pointer (it only has
a single assignment done before the key even
goes live). As that is otherwise harmless, I
decided to make it part of this patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we are disconnecting, we set PS off, but this happens before we
send the deauth/disassoc request. When the deauth/disassoc frames are
sent, we trigger the dynamic ps timer, which then times out and turns
PS back on. Thus, PS remains on after disconnecting, causing problems
when associating again.
This can be fixed by preventing the timer to start when we're not
associated anymore.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping of internal mgmt packets is set to VO. Set the TID
value to match the queue mapping. Otherwise drivers that only look at
the TID might get confused.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In xmit path, devices that do full hardware crypto (including
TKIP MMIC) need no tailroom. For such devices, tailroom
reservation can be skipped if all the keys are programmed into
the hardware (i.e software crypto is not used for any of the
keys) and none of the keys wants software to generate Michael
MIC.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These warnings are exposed by gcc 4.6.
net/mac80211/sta_info.c: In function 'sta_info_cleanup_expire_buffered':
net/mac80211/sta_info.c:590:32: warning: variable 'sdata' set but not used
net/mac80211/ibss.c: In function 'ieee80211_rx_mgmt_auth_ibss':
net/mac80211/ibss.c:43:34: warning: variable 'status_code' set but not used
net/mac80211/work.c: In function 'ieee80211_send_assoc':
net/mac80211/work.c:203:9: warning: variable 'len' set but not used
net/mac80211/tx.c: In function '__ieee80211_parse_tx_radiotap':
net/mac80211/tx.c:1039:35: warning: variable 'sband' set but not used
net/mac80211/mesh.c: In function 'ieee80211_mesh_rx_queued_mgmt':
net/mac80211/mesh.c:616:28: warning: variable 'ifmsh' set but not used
...
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To NL80211_MESH_SETUP_IE. This reflects our ability to insert any ie
into a mesh beacon, not simply path selection ies.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clear IEEE80211_STA_NULLFUNC_ACKED flag on disabling power
save. Without this fix, there is a chance of setting CONF_PS
before sending nullfunc frame.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ap" is the address of sdata->u.ap so it can never be NULL here. Also
we dereferenced it on the previous line. I removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using skb_header_cloned to check if it's safe to write to the skb is not
enough - mac80211 also touches the tailroom of the skb.
Initially this check was only used to increase a counter, however this
commit changed the code to also skip skb data reallocation if no extra
head/tailroom was needed:
commit 4cd06a344d
mac80211: skip unnecessary pskb_expand_head calls
It added a regression at least with iwl3945, which is fixed by this patch.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should decrease un-necessary flushes, on/off channel work,
and channel changes in cases where the only scanned channel is
the current operating channel.
* Removes SCAN_OFF_CHANNEL flag, uses SDATA_STATE_OFFCHANNEL
and is-scanning flags instead.
* Add helper method to determine if we are currently configured
for the operating channel.
* Do no blindly go off/on channel in work.c Instead, only call
appropriate on/off code when we really need to change channels.
Always enable offchannel-ps mode when starting work,
and disable it when we are done.
* Consolidate ieee80211_offchannel_stop_station and
ieee80211_offchannel_stop_beaconing, call it
ieee80211_offchannel_stop_vifs instead.
* Accept non-beacon frames when scanning on operating channel.
* Scan state machine optimized to minimize on/off channel
transitions. Also, when going on-channel, go ahead and
re-enable beaconing. We're going to be there for 200ms,
so seems like some useful beaconing could happen.
Always enable offchannel-ps mode when starting software
scan, and disable it when we are done.
* Grab local->mtx earlier in __ieee80211_scan_completed_finish
so that we are protected when calling hw_config(), etc.
* Pass probe-responses up the stack if scanning on local
channel, so that mlme can take a look.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On review of 'zd1211rw: implement beacon fetching and handling
ieee80211_get_buffered_bc()', Christian Lamparter noted that [1]:
Since zd_beacon_done also uploads the next beacon so long in advance,
there could be an equally long race between the outdated state of the
next beacon's DTIM broadcast traffic indicator (802.11-2007 7.3.2.6)
which -in your case- was uploaded almost a beacon interval ago and
the xmit of ieee80211_get_buffered_bc *now*.
The dtim bc/mc bit might be not set, when a mc/bc arrived after the
beacon was uploaded, but before the "beacon done event" from the
hardware. So, dozing stations don't expect the broadcast traffic
and of course, they might miss it completely.
It's probably better to fix this in mac80211 (see the attached hack).
[1] http://marc.info/?l=linux-wireless&m=129435041117256&w=2
CC: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rate-control is performed in HW, we cannot calculate frame
duration as we do not have the skb transmission rate in SW.
ieee80211_tx_h_calculate_duration() should only be called when
ieee80211_tx_h_rate_ctrl() has been called before to initialize data
in skb->cb. This doesn't happen for drivers with HW rate-control.
Fixes the following warning when operating in AP-mode
in a driver with HW rate-control.
WARNING: at net/mac80211/tx.c:57 ieee80211_duration+0x54/0x1d8 [mac80211]()
Modules linked in: wl1271_sdio wl1271 firmware_class crc7 mac80211 cfg80211
[<c0046090>] (unwind_backtrace+0x0/0x124) from [<c0064c10>] (warn_slowpath_common+0x4c/0x64)
[<c0064c10>] (warn_slowpath_common+0x4c/0x64) from [<c0064c40>] (warn_slowpath_null+0x18/0x1c)
[<c0064c40>] (warn_slowpath_null+0x18/0x1c) from [<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211])
[<bf040e34>] (ieee80211_duration+0x54/0x1d8 [mac80211]) from [<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211])
[<bf04200c>] (invoke_tx_handlers+0xfa0/0x1088 [mac80211]) from [<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211])
[<bf042178>] (ieee80211_tx+0x84/0x248 [mac80211]) from [<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211])
[<bf042f44>] (ieee80211_tx_pending+0x12c/0x278 [mac80211]) from [<c0069a9c>] (tasklet_action+0x68/0xbc)
[<c0069a9c>] (tasklet_action+0x68/0xbc) from [<c006a044>] (__do_softirq+0x84/0x114)
[<c006a044>] (__do_softirq+0x84/0x114) from [<c006a1b8>] (do_softirq+0x48/0x54)
[<c006a1b8>] (do_softirq+0x48/0x54) from [<c006a4f8>] (local_bh_enable+0x98/0xcc)
[<c006a4f8>] (local_bh_enable+0x98/0xcc) from [<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271])
[<bf074e60>] (wl1271_rx+0x2e8/0x3a4 [wl1271]) from [<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271])
[<bf071ae4>] (wl1271_irq_work+0x230/0x310 [wl1271]) from [<c0076864>] (process_one_work+0x208/0x350)
[<c0076864>] (process_one_work+0x208/0x350) from [<c0076e14>] (worker_thread+0x1cc/0x300)
[<c0076e14>] (worker_thread+0x1cc/0x300) from [<c007bb88>] (kthread+0x84/0x8c)
[<c007bb88>] (kthread+0x84/0x8c) from [<c0041494>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.
To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mesh is disabled, mac80211 was returning
beacons with an empty mesh ID. That isn't
desirable, even if drivers shouldn't be trying
to get beacons to start with.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mppath is mesh related parameter and maybe unused
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrote code for checking if the destination is proxied by a mesh portal, to facilitate better
understanding of the functionality.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a bunch of
warning: ‘inline’ is not at beginning of declaration
messages when building a 'make allyesconfig' kernel with -Wextra.
These warnings are trivial to kill, yet rather annoying when building with
-Wextra.
The more we can cut down on pointless crap like this the better (IMHO).
A previous patch to do this for a 'allnoconfig' build has already been
merged. This just takes the cleanup a little further.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fixed a bug where if a mesh interface has a different MAC address from its bridge
interface, then it would not be able to send data traffic to any other mesh node.
This also adds support for communication between mesh nodes and external bridged
nodes by using a 6 address format if the source is a node within the mesh and the
destination is an external node proxied by a mesh portal.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi and other drivers like to blink their LED
based on throughput. Implement this generically in
mac80211, based on a throughput table the driver
specifies. That way, drivers can set the blink
frequencies depending on their desired behaviour
and max throughput.
All the drivers need to do is provide an LED class
device, best with blink hardware offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an skb is shared, it needs to be duplicated, along with its data buffer.
If the skb does not have enough headroom, using skb_copy might cause the data
buffer to be copied twice (once by skb_copy and once by pskb_expand_head).
Fix this by using skb_clone initially and letting ieee80211_skb_resize sort
out the rest.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the skb is not cloned and we don't need any extra headroom, there
is no point in reallocating the skb head.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4. If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).
The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft. See
section 7.1.3.6.3 in current draft (8.0).
Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats. But I thought I better
remove it before someone does start using it.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for split default keys (unicast
and multicast) in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last_tx_rate field was also updated for non-data frames that are
often sent with a lower rate (for example management frames at 1 Mbps).
This is confusing when the data rate is actually much higher.
Hence, only update the last_tx_rate field with tx rate information
gathered from last data frames.
If the rate control algorithm filled in txrc.reported_rate we don't need
to verify this information.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for frame injection to work properly for some use cases
(e.g., finding the station entry and keys for encryption), mac80211
needs to find the correct sdata entry. This works when the main vif
is in AP mode, but commit a2c1e3dad5
broke this particular use case for station main vif. While this type of
injection is quite unusual operation, it has some uses and we should fix
it. Do this by changing the monitor vif sdata selection to allow station
vif to be selected instead of limiting it to just AP vifs. We still need
to skip some iftypes to avoid selecting unsuitable vif for injection.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.
If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hdr pointer is left dangling after call to ieee80211_skb_resize. This
can cause guards around mesh path selection to fail.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are subqueue helpers so that we don't
need to get the TX queue and then wake/stop
it, use those helpers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some vendor specified mechanisms for 802.1X-style
functionality use a different protocol than EAP
(even if EAP is vendor-extensible). Support this
in mac80211 via the cfg80211 API for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers to specify their own set of cipher
suites to advertise vendor-specific ciphers. The
driver is then required to implement hardware
crypto offload for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_hdr only used when CONFIG_MAC80211_MESH is defined
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Standardize logging messages from
printk(KERN_<level> "%s: " fmt , wiphy_name(foo), args);
to
wiphy_<level>(foo, fmt, args);
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function ieee80211_subif_start_xmit the logic related with
meshdrlen is under CONFIG_MAC80211_MESH macro, but in one place it isn't.
This is some update for this
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I just had the following:
WARNING: at drivers/net/wireless/iwlwifi/iwl-agn-tx.c:574 iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]()
Call Trace:
<IRQ> [<ffffffff8105c5df>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8105c63a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0290b46>] iwlagn_tx_skb+0x1576/0x15f0 [iwlagn]
[<ffffffffa027076c>] iwl_mac_tx+0x5c/0x260 [iwlagn]
[<ffffffffa01bdf5b>] __ieee80211_tx+0x10b/0x1a0 [mac80211]
[<ffffffffa01bfb86>] ieee80211_tx_pending+0x186/0x2d0 [mac80211]
[<ffffffff81062ea5>] tasklet_action+0x125/0x130
[<ffffffff810634a6>] __do_softirq+0x106/0x270
[<ffffffff8100c09c>] call_softirq+0x1c/0x30
iwlagn 0000:02:00.0: Attempting to modify non-existing station 107
Note that 107 == 0x6b which is slab poison.
The reason is that mac80211 passed a freed station
pointer to mac80211, because as it happened iwlwifi
reset itself while mac80211 was disconnecting from
the network.
It turns out that we do take care to look up the
station pointer in ieee80211_tx_pending_skb, but
then don't use it, which obviously is a bug. Fix
this by removing the ieee80211_tx_h_sta handler
and assigning the station pointer directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver or rate control requests starting
or stopping an aggregation session, that currently
causes a direct callback into the driver, which
could potentially cause locking problems. Also,
the functions need to be callable from contexts
that cannot sleep, and thus will interfere with
making the ampdu_action callback sleeping.
To address these issues, add a new work item for
each station that will process any start or stop
requests out of line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we allocate some memory for each TX
aggregation session and additionally keep a
state bitmap indicating the state it is in.
By using RCU to protect the pointer, moving
the state into the structure and some locking
trickery we can avoid locking when the TX agg
session is fully operational.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also simplify the flags assignment into a single statement at the
end of ieee80211_beacon_get_tim.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently whenever rts thresold is set, every packet will use RTS
protection no matter its size exceeds the threshold or not. This is
due to a bug in the rts threshold check.
if (len > tx->local->hw.wiphy->rts_threshold) {
txrc.rts = rts = true;
}
Basically it is comparing an int (len) and a u32 (rts_threshold),
and the variable len is assigned as:
len = min_t(int, tx->skb->len + FCS_LEN,
tx->local->hw.wiphy->frag_threshold);
However, when frag_threshold is "-1", len is always "-1", which is
0xffffffff therefore rts is always set to true.
CC: stable@kernel.org
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta_cleanup timer is used to periodically expire buffered frames from the
tx buf. The timer is executing periodically, regardless of the need for it.
This is wasting resources.
Fix this simply by not restarting the sta_cleanup timer if the tx buffer was
empty. Restart the timer when there is some more tx-traffic.
Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BIP (part of IEEE 802.11w) is only supposed to be used with
group-addressed frames. We ended up picking it as a default mechanism
for every management whenever we did not have a STA entry for the
destination (e.g., for Probe Response to a STA that is not
associated). While the extra MMIE in the end of management frames
should not break frames completed in most cases, there is no point in
doing this. Fix key selection to pick the default management key only
if the frame is sent to multicast/broadcast address and the frame is a
robust management frame.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.
In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need "sdata" any more after:
d84f323477
mac80211: remove dev_hold/put calls
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many drivers would like to sleep during station
addition and removal, and currently have a high
complexity there from not being able to.
This introduces two new callbacks sta_add() and
sta_remove() that drivers can implement instead
of using sta_notify() and that can sleep, and
the new sta_add() callback is also allowed to
fail.
The reason we didn't do this previously is that
the IBSS code wants to insert stations from the
RX path, which is a tasklet, so cannot sleep.
This patch will keep the station allocation in
that path, but moves adding the station to the
driver out of line. Since the addition can now
fail, we can have IBSS peer structs the driver
rejected -- in that case we still talk to the
station but never tell the driver about it in
the control.sta pointer. If there will ever be
a driver that has a low limit on the number of
stations and that cannot talk to any stations
that are not known to it, we need to do come up
with a new strategy of handling larger IBSSs,
maybe quicker expiry or rejecting peers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upstream radiotap has adopted the namespace
proposal David Young made and I then took care
of, for which I had adapted the radiotap parser
as a library outside the kernel. This brings
the in-kernel parser up to speed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When injecting frames, mac80211 currently looks for the first AP
interface that matches the source address of the injected frame.
This breaks when such a frame is directed at a STA that has been moved
to a VLAN. This patch fixes it by using sta_info_get_bss instead of
sta_info_get, which also finds stations belonging to a VLAN interface
of the same BSS as the AP interface.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an injected frame gets buffered for a powersave STA or filtered
and retransmitted, mac80211 attempts to parse the radiotap header
again, which doesn't work because it's gone at that point.
This patch adds a new flag for checking the availability of a radiotap
header, so that it only attempts to parse it once, reusing the tx info
on the next call to ieee80211_tx().
This fixes severe issues with rekeying in AP mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What a stupid mistake. In
commit 813d766940
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Sun Jan 17 01:47:58 2010 +0100
mac80211: move control.hw_key assignment
I inserted code testing the wrong flags field,
which means that the test is almost always true
(it's really testing for the peer's WMM support)
and thus the later parts of the stack assume hw
crypto will be done even if that's not true.
Obviously, that broke software crypto. Maxim
said so specifically, and Jochen probably uses
some cipher that iwl3945 doesn't support in
hardware, which might also explain that Maxim
reports that even hw crypto is broken.
Fix this to test the right flags field.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Reported-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin reported a crash in ieee80211_tx_h_select_key():
http://marc.info/?l=linux-wireless&m=126419655108528&w=2
This is a regression from patch "mac80211: move control.hw_key assignment".
Fix it as suggested by Johannes, adding an else statement to make sure
that tx->key is not accessed when it's null.
Compile-tested only.
Reported-by: Pavel Roskin <proski@gnu.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_tx_h_select_key might decide that a frame
need not be encrypted at all, in which case it will
clear tx->key. In that case it may crash if a key
was previously selected, e.g. as the default key.
This is also due to my patch
"mac80211: move control.hw_key assignment".
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In an earlier commit,
mac80211: disable software retry for now
Pavel Roskin reported a problem that seems to be due to
software retry of already transmitted frames. It turns
out that we've never done that correctly, but due to
some recent changes it now crashes in the TX code. I've
added a comment in the patch that explains the problem
better and also points to possible solutions -- which
I can't implement right now.
I disabled software retry of failed/filtered frames
because it was broken. With the work of the previous
patches, it now becomes fairly easy to re-enable it
by adding a flag indicating that the frame shouldn't
be modified, but still running it through the transmit
handlers to populate the control information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 asks a driver to encrypt a frame, it
must assign the control.hw_key pointer for it to
know which key to use etc. Currently, mac80211 does
this whenever it would software-encrypt a frame.
Change the logic of this code to assign the hw_key
pointer when selecting the key, and later check it
when deciding whether to encrypt the frame or let
it be encrypted by the hardware. This allows us to
later simply skip the encryption function since it
no longer modifies the TX control.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no value in setting a flag that will
never be checked after this point, this seems
to be legacy code -- I think previously the
flag was used to check whether to encrypt the
frame or not. Now, however, the flag need not
be set, and setting it actually interferes if
the frame will be processed again later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This TX handler is used only for assigning the
station pointer in the control information, so
give it a better name. Also move it before rate
control.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make U-APSD client mode effective, we must not wake up from dynamic power
save when transmitting frames. So if dynamic power save is enabled, it needs
check the queue the transmitted packet is in and decide if we need to wake
up or not.
In a perfect world, where all packets would have correct QoS tags, U-APSD
enabled queues should not trigger wakeup from power save. But in the real
world, where very few packets have correct QoS tags, this won't work. For
example, if only voip class has U-APSD enabled and we send a packet in voip
class, but the packets we receive are in best effort class, we would receive
the packets with the legacy power save method. And that would increase
latencies too much from a voip application point of view.
The workaround is to enable U-APSD for all qeueus and still use dynamic ps
wakeup for all other queues except voip. That way we can still save power
with a voip application and not sacrifice latency. Normal traffic (in
background, best effort or video class) would still trigger wakeup from
dynamic power save.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently dynamic ps check is in ieee80211_xmit(), but it's cleaner
to have a separate tx handler for this. Also this is a prerequisite for
U-APSD client mode which needs to know the queue frame is in.
Also need_dynamic_ps() function is embedded to the tx handler.
No functional changes expect that the code is run in a later phase than
originally.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If frames are transmitted on 4-addr ap vlan interfaces with no station,
they end up being transmitted unencrypted, even if the ap interface
uses WPA. This patch add some sanity checking to make sure that this
does not happen.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Certain type of hardware, for example wl1251 and wl1271, need a template
for the Probe Request. Create a function ieee80211_probereq_get() which
creates the template and drivers send it to hardware.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware, for example wl1251 and wl1271, handle the transmission
of power save related frames in hardware, but the driver is responsible
for creating the templates. It's better to create the templates in mac80211,
that way all drivers can benefit from this.
Add two new functions, ieee80211_pspoll_get() and ieee80211_nullfunc_get()
which drivers need to call to get the frame. Drivers are also responsible
for updating the templates after each association.
Also new struct ieee80211_hdr_3addr is added to ieee80211.h to make it
easy to calculate length of the Nullfunc frame.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend struct cfg80211_bitrate_mask to actually use a bitfield mask
instead of just a single fixed or maximum rate index. This change
itself does not modify the behavior (except for debugfs files), but it
prepares cfg80211 and mac80211 for a new nl80211 command for setting
which rates can be used in TX rate control.
Since frames are now going through the rate control algorithm
unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now
be removed. The RC implementations can use the rate_idx_mask value to
optimize their behavior if only a single rate is enabled.
The old max_rate_idx in struct ieee80211_tx_rate_control is maintained
(but commented as deprecated) for backwards compatibility with existing
RC implementations. Once these implementations have been updated to
use the more generic rate_idx_mask, the max_rate_idx value can be
removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the basic rate set is configured to not include the lowest rate
(e.g., basic rate set = 6, 12, 24 Mbps in IEEE 802.11g mode), the AP
should not send out broadcast frames at 1 Mbps. This type of
configuration can be used to optimize channel usage in cases where
there is no need for backwards compatibility with IEEE 802.11b-only
devices.
In AP mode, mac80211 was unconditionally using the lowest rate for
Beacon frames and similarly, with all rate control algorithms that use
rate_control_send_low(), the lowest rate ended up being used for all
broadcast frames (and all unicast frames that are sent before
association). Change this to take into account the basic rate
configuration in AP mode, i.e., use the lowest rate in the basic rate
set instead of the lowest supported rate when selecting the rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I removed the master netdev, we've been
keeping internal queues only, and even before
that we never told the networking stack above
the virtual interfaces about congestion. This
means that packets are queued in mac80211 and
the upper layers never know, possibly leading
to memory exhaustion and other problems.
This patch makes all interfaces multiqueue and
uses ndo_select_queue to put the packets into
queues per AC. Additionally, when the driver
stops a queue, we now stop all corresponding
queues for the virtual interfaces as well.
The injection case will use VO by default for
non-data frames, and BE for data frames, but
downgrade any data frames according to ACM. It
needs to be fleshed out in the future to allow
chosing the queue/AC in radiotap.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always using netif_running(sdata->dev)
use ieee80211_sdata_running(sdata) now which is
just an inline containing netif_running() for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 suspends it calls a driver's suspend callback
as a last step and after that the driver assumes no calls will
be made to it until we resume and its start callback is kicked.
If such calls are made, however, suspend can end up throwing
hardware in an unexpected state and making the device unusable
upon resume.
Fix this by preventing mac80211 to schedule dynamic_ps_disable_work
by checking for when mac80211 starts to suspend and starts
quiescing. Frames should be allowed to go through though as
that is part of the quiescing steps and we do not flush the
mac80211 workqueue since it was already done towards the
beginning of suspend cycle.
The other mac80211 issue will be hanled in the next patch.
For further details see refer to the thread:
http://marc.info/?t=126144866100001&r=1&w=2
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station management currently uses the virtual
interface, but you cannot add the same station to
multiple virtual interfaces if you're communicating
with it in multiple ways.
This restriction should be lifted so that in the
future we can, for instance, support bluetooth 3
with an access point that mac80211 is already
associated to.
We can do that by requiring all sta_info_get users
to provide the virtual interface and making the RX
code aware that an address may match more than one
station struct. Thanks to the previous patches this
one isn't all that large and except for the RX and
TX status paths changes has low complexity.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.
The rate control algorithms also need TX status, but
they don't require it.
Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.
This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's very likely that not many devices will support
four-address mode in station or AP mode so introduce
capability bits for both modes, set them in mac80211
and check them when userspace tries to use the mode.
Also, keep track of 4addr in cfg80211 (wireless_dev)
and not in mac80211 any more. mac80211 can also be
improved for the VLAN case by not looking at the
4addr flag but maintaining the station pointer for
it correctly. However, keep track of use_4addr for
station mode in mac80211 to avoid all the derefs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the flags moved into skb->cb, there's no
longer a need to have the encrypt bool passed
into the function, anyone who requires it set
to 0 (false) can just set the flag directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices implement the entire rate control in
firmware in some way, like wl1271 or like iwlwifi
which does some things in software but not a lot.
Therefore generic software rate control is rather
useless for them and just adds avoidable overhead
to the transmit path.
It's fairly simple to let drivers indicate that
they do not need rate control, but they need to
fulfil a number of conditions that we encode in
WARN_ONs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The netdev broadcast address cannot change from
all-ones so there's no need to use it; we can
instead hard-code it. Since we already have an
instance in tkip.c, which will be shared if it
is marked static const, doing this reduces text
size at no data/bss cost.
The real motivation for this is, of course, the
desire to get rid of almost all uses of netdevs
in mac80211 so that auditing their use becomes
easier.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we move the rcu sections a little, there's
no need to touch the device refcount.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BSSID is now set to the TA.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Andrey Yurovsky <andrey@cozybit.com>
Tested-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations it might be useful to run a network with an
Access Point and multiple clients, but with each client bridged
to a network behind it. For this to work, both the client and the
AP need to transmit 4-address frames, containing both source and
destination MAC addresses.
With this patch, you can configure a client to communicate using
only 4-address frames for data traffic.
On the AP side you can enable 4-address frames for individual
clients by isolating them in separate AP VLANs which are configured
in 4-address mode.
Such an AP VLAN will be limited to one client only, and this client
will be used as the destination for all traffic on its interface,
regardless of the destination MAC address in the packet headers.
The advantage of this mode compared to regular WDS mode is that it's
easier to configure and does not require a static list of peer MAC
addresses on any side.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices require that all frames to a station
are flushed when that station goes into powersave
mode before being able to send frames to that
station again when it wakes up or polls -- all in
order to avoid reordering and too many or too few
frames being sent to the station when it polls.
Normally, this is the case unless the station
goes to sleep and wakes up very quickly again.
But in that case, frames for it may be pending
on the hardware queues, and thus races could
happen in the case of multiple hardware queues
used for QoS/WMM. Normally this isn't a problem,
but with the iwlwifi mechanism we need to make
sure the race doesn't happen.
This makes mac80211 able to cope with the race
with driver help by a new WLAN_STA_PS_DRIVER
per-station flag that can be controlled by the
driver and tells mac80211 whether it can transmit
frames or not. This flag must be set according to
very specific rules outlined in the documentation
for the function that controls it.
When we buffer new frames for the station, we
normally set the TIM bit right away, but while
the driver has blocked transmission to that sta
we need to avoid that as well since we cannot
respond to the station if it wakes up due to the
TIM bit. Once the driver unblocks, we can set
the TIM bit.
Similarly, when the station just wakes up, we
need to wait until all other frames are flushed
before we can transmit frames to that station,
so the same applies here, we need to wait for
the driver to give the OK.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The multi-line code in this macro wasn't wrapped
in do {} while (0) so we cannot use it in an if()
branch safely in the future -- fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac80211 is asked to buffer multicast frames
in AP mode, it will not set the flag indicating
that the frames should be sent after the DTIM
beacon for those frames buffered in software. Fix
this little inconsistency by always setting that
flag in the buffering code path.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compared to ieee80211_beacon_get(), the new function
ieee80211_beacon_get_tim() returns information on the
location and length of the TIM IE, which some drivers
need in order to generate the TIM on the device. The
old function, ieee80211_beacon_get(), becomes a small
static inline wrapper around the new one to not break
all drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In TX path it was assumed that dynamic power save works only if
IEEE80211_HW_PS_NULLFUNC_STACK is set. But is not the case, there are
devices which have nullfunc support in hardware but need mac80211
to handle dynamic power save timers, TI's wl1251 is one of them.
The fix is to not check for IEEE80211_HW_PS_NULLFUNC_STACK in
is_dynamic_ps_enabled(), instead check IEEE80211_HW_SUPPORTS_PS and
IEEE80211_HW_SUPPORTS_DYNAMIC_PS flags and act accordingly.
Tested with wl1251.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refactor dynamic power save checks to a function of it's own for better
readibility. No functional changes.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hostapd injects a frame, e.g. an authentication or association
response, mac80211 looks for a suitable access point virtual interface
to associate the frame with based on its source address. This makes it
possible e.g. to correctly assign sequence numbers to the frames.
A small typo in the ethernet address comparison statement caused a
failure to find a suitable ap interface. Sequence numbers on such
frames where therefore left unassigned causing some clients
(especially windows-based 11b/g clients) to reject them and fail to
authenticate or associate with the access point. This patch fixes the
typo in the address comparison statement.
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving data frames, we can send them only to
the interface they belong to based on transmitting
station (this doesn't work for probe requests). Also,
don't try to handle other frames for AP_VLAN at all
since those interface should only receive data.
Additionally, the transmit side must check that the
station we're sending a frame to is actually on the
interface we're transmitting on, and not transmit
packets to functions that live on other interfaces,
so validate that as well.
Another bug fix is needed in sta_info.c where in the
VLAN case when adding/removing stations we overwrite
the sdata variable we still need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consider the following step-by step:
1. A STA authenticates and associates with the AP and exchanges
traffic.
2. The STA reports to the AP that it is going to PS state.
3. Some time later the STA device goes to the stand-by mode (not only
its wi-fi card, but the device itself) and drops the association state
without sending a disassociation frame.
4. The STA device wakes up and begins authentication with an
Auth frame as it hasn't been authenticated/associated previously.
At the step 4 the AP "remembers" the STA and considers it is still in
the PS state, so the AP buffers frames, which it has to send to the STA.
But the STA isn't actually in the PS state and so it neither checks
TIM bits nor reports to the AP that it isn't power saving.
Because of that authentication/[re]association fails.
To fix authentication/[re]association stage of this issue, Auth, Assoc
Resp and Reassoc Resp frames are transmitted disregarding of STA's power
saving state.
N.B. This patch doesn't fix further data frame exchange after
authentication/[re]association. A patch in hostapd is required to fix
that.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mesh frames that could not be immediately resolved were queued with a NULL
info->control.vif. This patch moves the call to mesh_nexthop_lookup closer to
the point where it is handed over to ieee80211_tx(). This ensures that the
unresolved frames are ready to be sent once the path is resolved.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address. This was done to avoid interactions with widely
deployed lazy-WDS access points.
This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward. The
address fields used for group addressed frames is:
In 802.11 header
ToDS:0 FromDS:1
addr1: DA (broadcast/multicast address)
addr2: TA
addr3: Mesh SA
In address extension header:
addr4: SA (only present if frame was proxied)
Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's really easier to read if it's not indented
as much, so invert the condition and rearrange
the code so the smaller chunk is indented instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to mask the variable with 0xFFF0
since we ever only use it as a u16 and the lowest
four bits can't ever be non-zero. The compiler
cannot infer the latter, and therefore has to emit
code to do the masking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When encryption is used, the number of bytes
sent to the peer increases by the IV and ICV.
This is accounted if software encryption is
used, but not if the devices does hardware
encryption. To make the numbers comparable,
never account for that overhead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have a lot of frames to transmit at once, for
instance with fragmentation, it can be an optimisation
to only tell the DMA engine about them on the last
fragment/frame to avoid banging the IO too much. This
patch allows implementation such an optimisation by
telling the driver when more frames can be expected.
Currently, this is used by mac80211 only on fragmented
frames, but could also be used in the future on other
frames when the queue was full and there are multiple
frames pending.
Note that drivers need to be careful when using this
flag, they need to kick their DMA engines not just
when this flag is clear, but also when the queue gets
full so that progress can be made.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When enqueuing packets on the internal packet queue, we
need to ensure that we have a valid vif pointer since
that is required since the net namespace work. Add some
assertions to verify this, but also don't crash is for
some reason we don't end up with a vif pointer -- warn
and drop the packet in all these cases.
Since this code touches a number of hotpaths, it is
intended to be temporary, or maybe configurable in the
future, at least the bit that is in the path that gets
hit for every packet, ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was caused by patch:
"mac80211: cooperate more with network namespaces"
The version of the patch applied doesn't match Johannes' latest:
http://johannes.sipsolutions.net/patches/kernel/all/LATEST/NNN-mac80211-netns.patch
The skb->cb virtual interface data wasn't being reset for
reuse so ath9k pooped out when trying to dereference the
private rate control info from the skb.
BUG: unable to handle kernel NULL pointer dereference
RIP: 0010:[<ffffffffa0258173>] ath_tx_rc_status+0x33/0x150 [ath9k]
<-- snip etc -->
Reported-by: Davide Pesavento <davidepesa@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.
Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.
(Also remove a now dead function)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Bob Copeland <me@bobcopeland.com>
Tested-by: Bob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new scan flag "SCAN_OFF_CHANNEL" which basically tells us
that we are currently on a different channel for scanning and cannot
RX/TX. "SCAN_SW_SCANNING" tells us that we are currently running a
software scan but we might as well be on the operating channel to RX/TX.
While "SCAN_SW_SCANNING" is set during the whole scan "SCAN_OFF_CHANNEL"
is set when leaving the operating channel and unset when coming back.
Introduce two new scan states "SCAN_LEAVE_OPER_CHANNEL" and
"SCAN_ENTER_OPER_CHANNEL" which basically implement the functionality we
need to leave the operating channel (send a nullfunc to the AP and stop
the queues) and enter it again (send a nullfunc to the AP and start the
queues again).
Enhance the scan state "SCAN_DECISION" to switch back to the operating
channel after each scanned channel. In the future it sould be simple
to enhance the decision state to scan as much channels in a row as the
qos latency allows us.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are still two places in mac80211 that hardcode
the initial net namespace (init_net). One of them is
mandated by cfg80211 and will be removed by a separate
patch, the other one is used for finding the network
device of a pending packet via its ifindex.
Remove the latter use by keeping track of the device
pointer itself, via the vif pointer, and avoid it
going stale by dropping pending frames for a given
interface when the interface is removed.
To keep track of the vif pointer for the correct
interface, change the info->control.vif pointer's
internal use to always be the correct vif, and only
move it to the vif the driver expects (or NULL for
monitor interfaces and injected packets) right before
giving the packet to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The removal of the master netdev broke the mesh forwarding path. This patch
fixes it by using the new internal 'pending' queue.
As a result of this change, mesh forwarding no longer does the inefficient
802.11 -> 802.3 -> 802.11 conversion that was done before.
[Changes since v1]
Suggested by Johannes:
- Select queue before adding to mpath queue
- ieee80211_add_pending_skb -> ieee80211_add_pending_skbs
- Remove unnecessary header wme.h
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_xmit() cannot be called with tasklets enabled
because it is normally called from within a tasklet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we're associated we should be able to send data to
target sta. If we cannot we may be trying to use the incorrect
band to talk to the sta. Lets catch any such cases, warn, and
drop the frames to not invalidate assumptions being made on
rate control algorithms when they have a valid sta to
communicate with. Any such cases should be handled and fixed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The location of the 802.11 header is calculated incorrectly due to a
wrong placement of parentheses. Found by kmemcheck.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't want to trigger moving between PS mode during scan,
because then we will sometimes end up sending nullfunc frames
during scan. We're supposed to only send one prior to scan
and after scan.
This fixes an oops which occured due to an assert in ath9k:
http://marc.info/?l=linux-wireless&m=124277331319024
The assert was happening because the rate control algorithm
figures it should find at least one valid dual stream or
single stream rate. Since we allow mac80211 to send nullfunc
frames during scan and dynamic PS was enabled at times we ended
up trying to send nullfunc frames for the target sta on the
wrong band for which we have no valid rate to communicate with
it. This breaks the assumptions in rate control.
We determine we also need to disable moving between PS modes
when not associated so lets just add that now as well, and we
should not have a ps_sdata when that interface cannot actually
go into PS because it's not associated.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return type has more than two values, but it can validly
only ever return TX_DROP and TX_CONTINUE, so use a bool
instead of ieee80211_tx_result.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.
Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the duration field for TX frames, skip the update for
PS-Poll frames that use this field for other purposes (AID).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's this internal wifi_wme_noack_test variable that
we use to set the QoS control if set. For one, it is
unlikely that it is set. Secondly, if set it needs to
influence the IEEE80211_TX_CTL_NO_ACK TX control flag,
and finally we should also be able to set it at all, so
make it available in debugfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To deter future rate scaling algorithm writers from requesting NO_ACK
packets to be retried, throw a WARN_ON_ONCE if the algorithm hands us
a try count over 1 for NO_ACK packet.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to later add tracing or verifications to the driver
calls mac80211 makes, this patch adds static inline wrappers
for all operations.
All calls are now written as
drv_<op>(local, ...);
instead of
local->ops-><op>(&local->hw, ...);
Where necessary, the wrappers also do existence checking and
return default values as appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fragmentation threshold is defined to be including the
FCS, and the code that sets the TX_FRAGMENTED flag correctly
accounts for those four bytes. The code that verifies this
doesn't though, which could lead to spurious warnings and
frames being dropped although everything is ok. Correct the
code by accounting for the FCS.
(JWL -- The problem is described here:
http://article.gmane.org/gmane.linux.kernel.wireless.general/32205 )
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts mac80211 to the new cfg80211 IBSS API, the
wext handling functions are called where appropriate.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets IEEE80211_TX_CTL_CLEAR_PS_FILT for outgoing
frames for a half-wake station.
this is necessary if one wants to get ps-poll working properly with a p54 ap.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of stopping the entire AC queue when enabling aggregation
(which was only done for hardware with aggregation queues) buffer
the packets for each station, and release them to the pending skb
queue once aggregation is turned on successfully.
We get a little more code, but it becomes conceptually simpler and
we can remove the entire virtual queue mechanism from mac80211 in
a follow-up patch.
This changes how mac80211 behaves towards drivers that support
aggregation but have no hardware queues -- those drivers will now
not be handed packets while the aggregation session is being
established, but only after it has been fully established.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We just found a bug in zd1211rw where it would reject
packets in the ->tx() method but leave them modified,
which would cause retransmit attempts with completely
bogus skbs, eventually leading to a panic due to not
having enough headroom in those.
This patch adds a sanity check to mac80211 to catch
such driver mistakes; in this case we warn and drop
the skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tx takes a struct ieee80211_tx_data argument, but only
uses a few of its members, namely 'skb' and 'sta'. Make that explicit,
so that less internal knowledge is required in ieee80211_tx_pending
and the possibility of introducing errors here is removed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pending packets code is quite incomprehensible, uses memory barriers
nobody really understands, etc. This patch reworks it entirely, using
the queue spinlock, proper stop bits and the skb queues themselves to
indicate whether packets are pending or not (rather than a separate
variable like before).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Internally, mac80211 requires the skb's queue mapping to be set
to the AC queue, not the virtual A-MPDU queue. This is not done
correctly currently, this patch moves the code down to directly
before the driver is invoked and adds a comment that it will be
moved into the driver later.
Since this requires __ieee80211_tx() to have the sta pointer,
make sure to provide it in ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fragmentation currently uses an allocated array to store the
fragment skbs, and then keeps track of which have been sent
and which are still pending etc. This is rather complicated;
make it simpler by just chaining the fragments into skb->next
and removing from that list when sent. Also simplifies all
code that needs to touch fragments, since it now only needs
to walk the skb->next list.
This is a prerequisite for fixing the stored packet code,
which I need to do for proper aggregation packet storing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_tx_h_check_assoc() was dropping everything else than probe
requests during software scan. So the nullfunc frame with the power save
bit was dropped and AP never received it. This meant that AP never
buffered any frames for the station during software scan.
Fix this by allowing to transmit both probe request and nullfunc frames
during software scan. Tested with stlc45xx.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This inline is useless and actually makes the code _longer_
rather than shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible to hit a kernel panic on NULL pointer dereference in
dev_queue_xmit() when sending power save buffered frames to a STA that
woke up from sleep. This happened when the buffered frame was requeued
for transmission in ap_sta_ps_end(). In order to avoid the panic, copy
the skb->dev and skb->iif values from the first fragment to all other
fragments.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits out the ibss code and data from managed (station) mode.
The reason to do this is to better separate the state machines, and have
the code be contained better so it gets easier to determine what exactly
a given change will affect, that in turn makes it easier to understand.
This is quite some churn, especially because I split sdata->u.sta into
sdata->u.mgd and sdata->u.ibss, but I think it's easier to maintain that
way. I've also shuffled around some code -- null function sending is only
applicable to managed interfaces so put that into that file, some other
functions are needed from various places so put them into util, and also
rearranged the prototypes in ieee80211_i.h accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware with AMPDU queues currently has broken aggregation.
This patch fixes it by making all A-MPDUs go over the regular AC queues,
but keeping track of the hardware queues in mac80211. As a first rough
version, it actually stops the AC queue for extended periods of time,
which can be removed by adding buffering internal to mac80211, but is
currently not a huge problem because people rarely use multiple TIDs
that are in the same AC (and iwlwifi currently doesn't operate as AP).
This is a short-term fix, my current medium-term plan, which I hope to
execute soon as well, but am not sure can finish before .30, looks like
this:
1) rework the internal queuing layer in mac80211 that we use for
fragments if the driver stopped queue in the middle of a fragmented
frame to be able to queue more frames at once (rather than just a
single frame with its fragments)
2) instead of stopping the entire AC queue, queue up the frames in a
per-station/per-TID queue during aggregation session initiation,
when the session has come up take all those frames and put them
onto the queue from 1)
3) push the ampdu queue layer abstraction this patch introduces in
mac80211 into the driver, and remove the virtual queue stuff from
mac80211 again
This plan will probably also affect ath9k in that mac80211 queues the
frames instead of passing them down, even when there are no ampdu queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.28.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Monitor mode is able to TX by using injected frames. We should
not allow injected frames to be sent unless allowed by regulatory
rules. Since AP mode uses a monitor interfaces to transmit
management frames we have to take care to not break AP mode as
well while resolving this. We can deal with this by allowing compliant
APs solutions to inform mac80211 if their monitor interface is
intended to be used for an AP by setting a cfg80211 flag for the
monitor interface. hostapd, for example, currently does its own
checks to ensure AP mode is not used on channels which require radar
detection. Once such solutions are available it can can add this
flag for monitor interfaces.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ADDBA request Action frame was sent out before 4-way handshake was
completed and the initial 802.11w code ended up dropping the frame
even if MFP was not enabled. While the sending of Action frames this
early is not really a good idea (will break with MFP enabled), we
should not break this for the MFP disabled case.
This patch fixes ieee80211_tx_h_select_key() not to drop management
frames if MFP is disabled. If MFP is enabled, Action frames will be
dropped before keys are set per IEEE 802.11w/D7.0. Other robust
management frames (i.e., Deauthentication and Disassociation frames)
are allowed unprotected prior to key configuration.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend CCMP to support encryption and decryption of unicast management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies hardware flags for powersave to support three different
flags:
* IEEE80211_HW_SUPPORTS_PS - indicates general PS support
* IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
* IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device
It also adds documentation for all this which explains how to set the
various flags.
Additionally, it fixes a few things:
* a spot where && was used to test flags
* enable CONF_PS only when associated again
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be needed for drivers that set the
IEEE80211_HW_NO_STACK_DYNAMIC_PS flag and still
want to handle dynamic PS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes an unnecessary assignment to info
in __ieee80211_tx() , tx.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a null data frame is generated from mac80211, it goes through
master_start_xmit and not through subif_start_xmit. Hence for the
power save timer to be triggered while sending this null data frame
also, the timer has to be reset from master_start_xmit.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After launching mesh discovery in tx path, reference count was not being
decremented. This was preventing module unload.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements dynamic power save for mac80211. Basically it
means enabling power save mode after an idle period. Implementing it
dynamically gives a good compromise of low power consumption and low
latency. Some hardware have support for this in firmware, but some
require the host to do it.
The dynamic power save is implemented by adding an timeout to
ieee80211_subif_start_xmit(). The timeout can be enabled from userspace
with Wireless Extensions. For example, the command below enables the
dynamic power save and sets the time timeout to 500 ms:
iwconfig wlan0 power timeout 500m
Power save now only works with devices which handle power save in firmware.
It's also disabled by default and the heuristics when and how to enable is
considered as a policy decision and will be left for the userspace to handle.
In case the firmware has support for this, drivers can disable this feature
with IEEE80211_HW_NO_STACK_DYNAMIC_PS.
Big thanks to Johannes Berg for the help with the design and code.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no driver that actually does fragmentation on the
device, and the callback is buggy (when it returns an error,
mac80211's fragmentation status is changed so reading the
frag threshold from userspace reads the new value despite
the error). Let's just remove it, if we really find some
hardware supporting it we can add it back later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unnecessary parameter in ieee80211_beacon_add_tim() and
removes unneeded definition and assignment for bdev (instance of net_device) in
ieee80211_beacon_get() and in ieee80211_get_buffered_bc()
(all in tx.c).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A warning would be printed for every packet that
is transmitted if the rate control information isn't
setup. Change this to WARN_ON_ONCE.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've come to think that not providing sequence numbers for
the normal STA mode case was a mistake, at least two drivers
now had to implement code they wouldn't otherwise need, and
I believe at76_usb and adm8211 might be broken.
This patch makes mac80211 assign a sequence number to all
those frames that need one except beacons. That means that
if a driver only implements modes that do not do beaconing
it need not worry about the sequence number.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also remove a few stray DECLARE_MAC_BUF that were no longer
used at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- This patch (against the linux-wireless-next git tree) removes a
redundant check in ieee80211_master_start_xmit (net/mac80211/tx.c)
and adjust indentation in this method accordingly.
In this method, there is no need to call again the
ieee80211_is_data() method; this is checked immediately before, in the
"if" command (we will not enter this block unless ieee80211_is_data()
is true, so that the "and" (&&) condition in that "if" command will be
fullfilled ).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes doubly defined variables in ieee80211_master_start_xmit
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.
There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.
Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mesh code doesn't support bridging mesh point interfaces
with wired ethernet or AP to construct an MPP or MAP. This patch adds
code to support the "6 address frame format packet" functionality to
mesh point interfaces. Now the mesh network can be used as backhaul
for end to end communication.
Signed-off-by: Li YanBo <dreamfly281@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to register the master netdev with cfg80211,
in fact, this is quite dangerous and lead to having to add
checks for the master interface all over the config handlers.
This patch removes the "ieee80211_ptr" from the master iface
in favour of having a small netdev_priv() associated with
the master interface that stores the ieee80211_local pointer.
Because of this, a lot of code in the configuration handlers
can go away. To make this patch easier to verify I have also
removed a number of wiphy_priv() calls in favour of getting
the sdata first and then the local pointer from that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
You can just pull up a monitor interface to get much more
detailed information, or, when debugging a driver, insert
dump code into the driver (which usually you will have to
do anyway to dump the driver-specific information). Hence
this option is useless.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon counters mac80211 keeps are only used for debugfs,
unfortunately, they are incorrect for many hardware designs,
namely any design that has a beacon template. Hence, remove the
counters so we don't create the impression they are usable.
This also allows removing the beacon MESH #ifdef again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg