This one doesn't have one of these nice cryptic names unfortunately.
v2: Added missing register bitmap
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Dont add WaDisableThreadStallDopClockGating as not SKL WA. (Found
by Damien Lespiau)
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Bikeshed commit message a bit as per Damien's suggestions.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add Skylake stepping Revision IDs definitions.
v1: Use existing revision id.
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Use magic __I915__ and bikeshed #defines as suggested by
Damien.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add framework for gen 9 HW WAs
v1: Changed SOC specific WA function to gen 9 common function (Req: Damien Lespiau)
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want to end up in a state where we track that the pipe has its
primary plane enabled when primary plane registers are programmed with
values that look possible but the plane actually disabled.
Refuse to read out the fb state when the primary plane isn't enabled.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now, we get a warning when taking over the firmware fb:
[drm:drm_atomic_plane_check] FB set but no CRTC
with the following backtrace:
[<ffffffffa010339d>] drm_atomic_check_only+0x35d/0x510 [drm]
[<ffffffffa0103567>] drm_atomic_commit+0x17/0x60 [drm]
[<ffffffffa00a6ccd>] drm_atomic_helper_plane_set_property+0x8d/0xd0 [drm_kms_helper]
[<ffffffffa00f1fed>] drm_mode_plane_set_obj_prop+0x2d/0x90 [drm]
[<ffffffffa00a8a1b>] restore_fbdev_mode+0x6b/0xf0 [drm_kms_helper]
[<ffffffffa00aa969>] drm_fb_helper_restore_fbdev_mode_unlocked+0x29/0x80 [drm_kms_helper]
[<ffffffffa00aa9e2>] drm_fb_helper_set_par+0x22/0x50 [drm_kms_helper]
[<ffffffffa050a71a>] intel_fbdev_set_par+0x1a/0x60 [i915]
[<ffffffff813ad444>] fbcon_init+0x4f4/0x580
That's because we update the plane state with the fb from the firmware, but we
never associate the plane to that CRTC.
We don't quite have the full DRM take over from HW state just yet, so
fake enough of the plane atomic state to pass the checks.
v2: Fix the state on which we set the CRTC in the case we're sharing the
initial fb with another pipe. (Matt)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment we use crtc->base.primary->fb to hold the initial
framebuffer allocation, disregarding if it's valid or not.
This lead to believe we were actually updating the fb at this point, but
it's not true and we haven't even called drm_framebuffer_init() on this
fb.
Instead, let's store the state in struct intel_initial_plane_config
until we know we can reuse that framebuffer.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tvrtko noticed a new warning on boot:
WARNING: CPU: 1 PID: 353 at include/linux/kref.h:47 drm_framebuffer_reference+0x6c/0x80 [drm]()
Call Trace:
[<ffffffff8161f10c>] dump_stack+0x4f/0x7b
[<ffffffff81052caa>] warn_slowpath_common+0xaa/0xd0
[<ffffffff81052d8a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa00d035c>] drm_framebuffer_reference+0x6c/0x80 [drm]
[<ffffffffa01c0df7>] update_state_fb.isra.54+0x47/0x50 [i915]
[<ffffffffa01ccd5c>] skylake_get_initial_plane_config+0x93c/0x950 [i915]
[<ffffffffa01e8721>] intel_modeset_init+0x1551/0x17c0 [i915]
[<ffffffffa02476e0>] i915_driver_load+0xed0/0x11e0 [i915]
[<ffffffff81627aa1>] ? _raw_spin_unlock_irqrestore+0x51/0x70
[<ffffffffa00ca8b7>] drm_dev_register+0x77/0x110 [drm]
[<ffffffffa00cda3b>] drm_get_pci_dev+0x11b/0x1f0 [drm]
[<ffffffff81098e3d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff81627aa1>] ? _raw_spin_unlock_irqrestore+0x51/0x70
[<ffffffffa0145276>] i915_pci_probe+0x56/0x60 [i915]
[<ffffffff813ad59c>] pci_device_probe+0x7c/0x100
[<ffffffff81466aad>] driver_probe_device+0x16d/0x380
We cannot take a reference at this point, not before
intel_framebuffer_init() and the underlying drm_framebuffer_init().
Introduced in:
commit 706dc7b549175e47f23e913b7f1e52874a7d0f56
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Feb 3 13:10:04 2015 -0800
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
v2: Don't move update_state_fb(). It was moved around because I
originally put update_state_fb() in intel_alloc_plane_obj() before
finding a better place. (Matt)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code look slightly better this way and will ease the next commit,
changing where we take the fb pointer from.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
update_state_fb() at the end of intel_find_plane_obj() is misleading as
it leads us to believe the update is done for all code path.
A successful call to intel_alloc_plane_obj() will return and
update_state_fb() is then only needed when we share a fb from another
CRTC. Put the update() function there then.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The check for previously reserved stolen space size for FBC in
i915_gem_stolen_setup_compression() did not take the compression
threshold into account. Fix this by storing and comparing to
uncompressed size instead.
The bug has been introduced in
commit 5e59f7175f
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Mon Jun 30 10:41:24 2014 -0700
drm/i915: Try harder to get FBC
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88975
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch implements core logic of SKL display power well.
v2: Addressed Imre's comments
- Added respective DDIs under power well #1 and #2
- Simplified repetitive code in power well programming
v3: Implemented Imre's comments
- Further simplified power well programming
- Made sure that PW 1 is enabled prior to PW 2
v4: Fix minor conflict with the the cherryview support (Damien)
v5: Add the PLL power domain to the always on power well (Damien)
v6: Disable BIOS power well (Imre)
Use power well data for comparison (Imre)
Put the PLL power domain into PW1 as its needed for CDCLK (Satheesh,
Damien)
v7: Addressed Imre's comments
- Lowered the time out to 1ms
- Added parantheses in macro
- Moved debug message and fixed wait_for interval
v8:
- Add a WARN() when swiching on an unknown power well (Imre, done by Damien)
- Whitespace fixes (spaces instead of tabs) (Damien)
v9: (Imre, done by Damien)
- Merge the register definitions with this patch
- Merge the MISC IO power well in this patch
v10: (Imre, done by Damien)
- Define the Misc I/O power domains to be the power well 1 ones as Misc I/O
needs to be enabled with PW1
- Added Transcoder A and VGA domains to PW 2
- Remove the MISC_IO power domains as well in the the always on
domains definition
- Move Misc I/O power well at the top of the power well list so it's turned
on right after PW1.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3,v6,v7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
plane->state->fb and plane->fb should always reference the same FB so
that atomic and legacy codepaths have the same view of display state.
In commit
commit db068420560511de80ac59222644f2bdf278c3d5
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Fri Jan 30 16:22:36 2015 -0800
drm/i915: Keep plane->state updated on pageflip
we already fixed one case where these two pointers could get out of
sync. However it turns out there are a few other places (mainly dealing
with initial FB setup at boot) that directly set plane->fb and neglect
to update plane->state->fb. If we never do a successful update through
the atomic pipeline, the RmFB cleanup code will look at the
plane->state->fb pointer, which has never actually been set to a
legitimate value, and try to clean it up, leading to BUG's.
Add a quick helper function to synchronize plane->state->fb with
plane->fb (and update reference counts accordingly) and call it
everywhere the driver tries to manually set plane->fb outside of the
atomic pipeline.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88909
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already track this in the intel_info struct.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Make the commit message a bit less terse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This isuue got introduced in -
commit 24ee0e6490
Author: Gaurav K Singh <gaurav.k.singh@intel.com>
Date: Fri Dec 5 14:24:21 2014 +0530
drm/i915: Update the DSI enable path to support dual
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the valleyview_set_rps() and gen6_set_rps() calls with
intel_set_rps() which itself does the IS_VALLEYVIEW() check. The
code becomes simpler since the callers don't have to do this check
themselves.
Most of the change was performe with the following semantic patch:
@@
expression E1, E2, E3;
@@
- if (IS_VALLEYVIEW(E1)) {
- valleyview_set_rps(E2, E3);
- } else {
- gen6_set_rps(E2, E3);
- }
+ intel_set_rps(E2, E3);
Adding intel_set_rps() and making valleyview_set_rps() and gen6_set_rps()
static was done manually. Also valleyview_set_rps() had to be moved a
bit avoid a forward declaration.
v2: Use a less greedy semantic patch
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter spotted a bug while reviewing some of my refactoring in this
are of the code. I'll quote:
"""
> @@ -9764,6 +9768,7 @@ static int intel_crtc_page_flip(struct drm_crtc *crtc,
> work->event = event;
> work->crtc = crtc;
> work->old_fb_obj = intel_fb_obj(old_fb);
> + work->old_tiling_mode = to_intel_framebuffer(old_fb)->tiling_mode;
Hm, that's actually an interesting bugfix - currently userspace could be
sneaky and destroy the old fb immediately after the flip completes and the
change the tiling of the underlying object before the unpin work had a
chance to run (needs some fudgin with rt prios to starve workers to make
this work though).
Imo the right fix is to hold a reference onto the fb and not the
underlying gem object. With that tiling is guaranteed not to change.
"""
This patch tries to implement the above proposed change.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are two sets of helper functions provided by the DRM core that can
implement the .update_plane() and .disable_plane() hooks in terms of a
driver's atomic entrypoints. The transitional helpers (which we have
been using so far) create a plane state and then use the plane's atomic
entrypoints to perform the atomic begin/check/prepare/commit/finish
sequence on that single plane only. The full atomic helpers create a
top-level atomic state (which is capable of holding multiple object
states for planes, crtc's, and/or connectors) and then passes the
top-level atomic state through the full "atomic modeset" pipeline.
Switching from the transitional to full helpers here shouldn't result in
any functional change, but will enable us to exercise/test more of the
internal atomic pipeline with the legacy API's used by existing
applications.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Until all drivers have transitioned to atomic, the framebuffer
associated with a plane is tracked in both plane->fb (for legacy) and
plane->state->fb (for all the new atomic codeflow). All of our modeset
and plane updates use drm_plane->update_plane(), so in theory plane->fb
and plane->state->fb should always stay in sync and point at the same
thing for i915. However we forgot about the pageflip ioctl case, which
currently only updates plane->fb and leaves plane->state->fb at a stale
value.
Surprisingly, this doesn't cause any real problems at the moment since
internally we use the plane->fb pointer in most of the places that
matter, and on the next .update_plane() call, we use plane->fb to figure
out which framebuffer to cleanup. However when we switch to the full
atomic helpers for update_plane()/disable_plane(), those helpers use
plane->state->fb to figure out which framebuffer to cleanup, so not
having updated the plane->state->fb pointer causes things to blow up
following a pageflip ioctl.
The fix here is to just make sure we update plane->state->fb at the same
time we update plane->fb in the pageflip ioctl.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
You can _never_ assert that a lock is not held, except in some very
restricted corner cases where it's guranteed that your code is running
single-threade (e.g. driver load before you've published any pointers
leading to that lock).
In addition the early return breaks a bunch of testcases since with
highly concurrent hangcheck stress tests the reset fails to work and
the test doesn't recover and time out.
This regression has been introduced in
commit b8d24a0656
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Wed Jan 28 17:03:14 2015 +0200
drm/i915: Remove nested work in gpu error handling
Aside: It is possible to check whether a given task doesn't hold a
lock, but only when lockdep is enabled, using the lockdep_assert_held
stuff.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88908
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The get_config() functions for ddi and dp_mst, used to read the value
of cpu_transcoder from the crtc->config instead of the state passed as
an argument. On the hardware state readout path, that happens to work
since the proper value is written to it before encoder->get_config() is
called. However, in the check_crtc() path, the state will be read from
the cpu_transcoder in the software tracking, instead of the one just
read out from hw. Using the field in the supplied intel_crtc_state
should do the right thing in both cases.
v2: Fix intel_ddi_get_config() too. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove request from list before unreferencing it, in case it's actually
the only reference. (Found by Tvrtko Ursulin)
This issue has been most likely introduced in
commit 6d3d8274bc
Author: Nick Hoath <nicholas.hoath@intel.com>
Date: Thu Jan 15 13:10:39 2015 +0000
drm/i915: Subsume intel_ctx_submit_request in to drm_i915_gem_request
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This simplifies __intel_set_mode() a little.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The checking for ack and also any subsequent mmio access
will serialize with setting the forcewake bit. Drop the
posting read as superfluous.
Note that in the put side we still want to keep the posting read
as it will ensure that the hw sees our forcewake release in a
timely manner and doesn't keep the hw powered up.
Comment from Chris:
On Wed, Jan 28, 2015 at 05:54:14PM +0200, Mika Kuoppala wrote:
> Ville Syrjälä <ville.syrjala@linux.intel.com> writes:
> > IIRC the posting read from same cache line actually fixed real bugs. So
> > I'm a bit worried about dropping them. But I suppose it's possible only
> > the _put side was important for those bugs.
>
> I found these:
>
> commit 6af2d180f8
> Author: Daniel Vetter <daniel.vetter@ffwll.ch>
> Date: Thu Jul 26 16:24:50 2012 +0200
>
> drm/i915: fix forcewake related hangs on snb
>
> commit 8dee3eea3c
> Author: Ben Widawsky <ben@bwidawsk.net>
> Date: Sat Sep 1 22:59:50 2012 -0700
>
> drm/i915: Never read FORCEWAKE
>
> https://bugs.freedesktop.org/show_bug.cgi?id=51738
> https://bugs.freedesktop.org/show_bug.cgi?id=52424
>
> The snb here seems to survive gem_dummy_reloc_loop and
> gem_ring_sync_loop in here with the get side posting removed.
Note that we kept the once associated with #52424, but judging by my
comments in #51738 the posting read is just a band aid anyway as a full
mb() itself was not adequate.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: paste relevant review discussion in.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_uncore_early_sanitize() will reset the forcewake registers. When
forcewake domains were introduced, the domain init was done after the
sanitization of the forcewake registers. And as the resetting of
registers use the domain accessors, we tried to reset the forcewake
registers with unitialized forcewake domains and failed.
Fix this by sanitizing after all the domains have been initialized. Do
per domain clearing of forcewake register on domain init so that
IVB can do early access to ECOBUS do determine the final configuration.
This regression was introduced in
commit 05a2fb157e
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Mon Jan 19 16:20:43 2015 +0200
drm/i915: Consolidate forcewake code
v2: Carve out ellc detect, fw_domain_reset for ivb/ecobus (Chris)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88805
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Darren Hart <dvhart@linux.intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV check into vlv_set_rps_idle() to simplify the caller a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now when we declare gpu errors only through our own dedicated
hangcheck workqueue there is no need to have a separate workqueue
for handling the resetting and waking up the clients as the deadlock
concerns are no more.
The only exception is i915_debugfs::i915_set_wedged, which triggers
error handling through process context. However as this is only used through
test harness it is responsibility for test harness not to introduce hangs
through both debug interface and through hangcheck mechanism at the same time.
Remove gpu_error.work and let the hangcheck work do the tasks it used to.
v2: Add a big warning sign into i915_debugfs::i915_set_wedged (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The removed functions can be resurrected in intel_dsi.c as need arises.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All of these are replaced by the drm core mipi dsi functions.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the drm core interfaces in preparation of removing our homebrew.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add basic support for using the drm mipi dsi framework for DSI. We don't
use device tree which is pretty much required by mipi_dsi_host_register
and friends, and we don't have the kind of device model the functions
expect either. So we cheat and use it as a library to abstract what we
need: a nice, clean interface for DSI transfers. This means we will have
to be careful with what functions we call, as the driver model devices
in mipi_dsi_host and mipi_dsi_device will *not* be initialized.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace intel_dsi_device and intel_dsi_dev_ops with drm_panel and
drm_panel_funcs. They are adequate for what we have now, and if we end
up needing more than this we should improve drm_panel. This will keep us
better aligned with the drm core infrastructure.
The panel driver initialization changes a bit. It still remains hideous,
but fixing that is beyond the scope here.
v2: extend mode config mutex to cover drm_panel_get_modes (Shobhit)
vbt_panel->intel_dsi = intel_dsi in vbt panel init (Shobhit)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mainly taking care of some register offsets, otherwise things are similar to
hsw. Also, programming ddi aux to use hardcoded values for psr data select.
v2: introduce EDP_PSR_AUX_BASE macro (Chris)
v3: Moving to HW tracking for SKL+ platforms, so activating source psr during
psr_enabling and then avoiding psr entries and exits for each frontbuffer
updates.
v4: Using SKL DDI AUX regs instead of changing PSR_AUX regs definition (Rodrigo)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Drop the hunks to short-circuit sw tracking: We'd need to
push this down one level, and I don't fully trust the test coverage
yet to do so. So much prefer we pick a whitelist approach for the
cases we know work correctly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The core fix was applied in
commit a63b03e2d2
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jan 6 10:29:35 2015 +0000
mutex: Always clear owner field upon mutex_unlock()
(note the absence of stable@ tag)
so we can now revert our band-aid commit 226e5ae9e5 for -next.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have had %x and %u intermixed. Bring everything in line and
use %x
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For example,
/sys/kernel/debug/dri/0/i915_hangcheck_info:
Hangcheck active, fires in 15887800ms
render ring:
seqno = -4059 [current -583]
action = 2
score = 0
ACTHD = 1ee8 [current 21f980]
max ACTHD = 0
v2: Include expiration ETA. Can anyone spot a problem?
v3: Convert for workqueued hangcheck (Mika)
v4: Print seqnos as unsigned ints (Ville)
v5: Print seqnos as hex (Chris)
Tested-By: PRC QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com) (v2)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When run as a timer, i915_hangcheck_elapsed() must adhere to all the
rules of running in a softirq context. This is advantageous to us as we
want to minimise the risk that a driver bug will prevent us from
detecting a hung GPU. However, that is irrelevant if the driver bug
prevents us from resetting and recovering. Still it is prudent not to
rely on mutexes inside the checker, but given the coarseness of
dev->struct_mutex doing so is extremely hard.
Give in and run from a work queue, i.e. outside of softirq.
v2: Use own workqueue to avoid deadlocks (Daniel)
Cleanup commit msg and add comment to i915_queue_hangcheck() (Chris)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <dnaiel.vetter@ffwll.chm>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Remove accidental kerneldoc comment starter, to appease the 0
day builder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The comment for intel_cpu_fifo_underrun_irq_handler() is not consistent
with the code and the rest of the comment for this routine. This patch
fixes this typo in comment.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have full atomic modeset support yet, but the "nuclear
pageflip" subset of functionality (i.e., plane operations only) should
be ready. Allow the user to force atomic on for debug purposes, or for
fixed-purpose embedded devices that will only use atomic for plane
updates.
The term 'nuclear' is used here instead of 'atomic' to make it clear
that this doesn't allow full atomic modeset support, just a (very
useful) subset of the atomic functionality.
We'll drop the kernel parameter and unconditionally enable atomic in a
future patch once all of the necessary pieces are in.
v2:
- Use module_param_named_unsafe() (Daniel)
- Simplify comment on DRIVER_ATOMIC guard (Daniel)
v3:
- Make the parameter "nuclear_pageflip" rather than just "nuclear"
for clarity. (Ander)
v4:
- Make the internal variable "nuclear_pageflip" as well as the
command-line option. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will exercise our atomic pipeline for legacy property updates.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The atomic helpers need these to prepare a new state object when
starting a new atomic operation.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even though we only support atomic plane updates at the moment, we still
need to add an .atomic_get_property() entrypoint for connectors before
we allow the driver to flip on the DRIVER_ATOMIC bit. As soon as that
bit gets set, the DRM core will start adding atomic connector properties
(in addition to the plane properties we care about at the moment), so we
need to be able to handle the new way the DRM core will interact with
us.
For simplicity, we just lookup driver-specific connector properties in
the usual shadow array maintained by the core. Once we get real atomic
modeset support for crtc's and planes, this code should be re-written to
pull the data out of crtc/connector state structures.
v2: Fix intel_dvo and intel_dsi that I missed on the first pass (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to enable/test plane updates via the atomic interface, but as
soon as we flip DRIVER_ATOMIC on, the DRM core will take some atomic
codepaths to lookup properties during drmModeGetConnector() and some of
those codepaths unconditionally dereference connector->state
(specifically when looking up the CRTC ID property in
drm_atomic_connector_get_property()). Create a dummy connector state
for each connector at init time to ensure the DRM core doesn't try to
dereference a NULL connector->state. The actual connector properties
will never be updated or contain useful information, but since we're
doing this specifically for testing/debug of the plane operations (and
only when a specific kernel module option is given), that shouldn't
really matter.
Once we start creating connector states, the DRM core will want to be
able to clean them up for us. We also need to hook up the destruction
entrypoint to the core's helper.
v2: Squash in the patch to set the state destruction hook (Ander & Bob)
v3: Only create dummy connector states when we're actually faking
atomic support. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the top-level atomic entrypoints for check/commit. These won't get
called yet; we still need to either enable the atomic ioctl or switch to
using the non-transitional atomic helpers for legacy operations.
v2:
- Use plane->pipe rather than plane->possible_crtcs while ensuring that
only a single CRTC is in use. Either way will work fine since i915
drm_plane's are always tied to a single CRTC, but plane->pipe is
slightly more intuitive. (Ander)
- Simplify crtc/connector checking logic. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we flip on the DRIVER_ATOMIC bit, the DRM core will start calling
this entrypoint to set and lookup driver-specific plane property values,
rather than maintaining a shadow copy in object->properties.
Note that although we add these functions to the plane vtable, they will
not yet be called. Future patches that switch our .set_property()
handler and/or enable full atomic functionality are required before
these code paths will be executed.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All of the previous refactoring/consolidation of plane code has resulted
in intel_primary_plane_funcs, intel_cursor_plane_funcs, and
intel_sprite_plane_funcs being identical. Replace all of these with a
single 'intel_plane_funcs' vtable for simplicity.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Runtime state that can be manipulated via properties should now go in
intel_plane_state/drm_plane_state so that it can be tracked as part of
an atomic transaction.
We add a new 'intel_create_plane_state' function so that the proper
initial value for this property (and future properties) doesn't have to
be repeated at each plane initialization site.
v2:
- Stick rotation in common drm_plane_state rather than
intel_plane_state. (Daniel)
- Add intel_create_plane_state() to consolidate the places where we
have to set initial state values. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace all the vlv_gpu_freq(), vlv_freq_opcode(),
*GT_FREQUENCY_MULTIPLIER, and /GT_FREQUENCY_MULTIPLIER instances
with intel_gpu_freq() and intel_freq_opcode() calls.
Most of the change was performed with the following semantic patch:
@@
expression E;
@@
(
- E * GT_FREQUENCY_MULTIPLIER
+ intel_gpu_freq(dev_priv, E)
|
- E *= GT_FREQUENCY_MULTIPLIER
+ E = intel_gpu_freq(dev_priv, E)
|
- E /= GT_FREQUENCY_MULTIPLIER
+ E = intel_freq_opcode(dev_priv, E)
|
- do_div(E, GT_FREQUENCY_MULTIPLIER)
+ E = intel_freq_opcode(dev_priv, E)
)
@@
expression E1, E2;
@@
(
- vlv_gpu_freq(E1, E2)
+ intel_gpu_freq(E1, E2)
|
- vlv_freq_opcode(E1, E2)
+ intel_freq_opcode(E1, E2)
)
@@
expression E1, E2, E3, E4;
@@
(
- if (IS_VALLEYVIEW(E1)) {
- E2 = intel_gpu_freq(E3, E4);
- } else {
- E2 = intel_gpu_freq(E3, E4);
- }
+ E2 = intel_gpu_freq(E3, E4);
|
- if (IS_VALLEYVIEW(E1)) {
- E2 = intel_freq_opcode(E3, E4);
- } else {
- E2 = intel_freq_opcode(E3, E4);
- }
+ E2 = intel_freq_opcode(E3, E4);
)
One hunk was manually undone as intel_gpu_freq() ended up
calling itself. Supposedly it would be possible to exclude
certain functions via !=~, but I couldn't get that to work.
Also the removal of vlv_gpu_freq() and vlv_opcode_freq() compat
wrappers was done manually.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the vlv_gpu_freq() and vlv_freq_opecode() functions to have
an intel_ prefix, and handle non-VLV/CHV platforms in them as well.
Leave the vlv_ names around for now since they're currently used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the 'gt_cur_freq_mhz' file shows the actual GPU frequency on
VLV/CHV, and the last requested frequency on other platforms. Change the
meaning of the file on VLV/CHV to follow the the other platforms, and
introduce a new file 'gt_act_freq_mhz' which shows the actual frequency
on all platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we don't call valleyview_set_rps() when changing the min/max
limits through sysfs if the current frequency is still within the new
limits. However that means we sometimes forget to update PMINTRMSK.
Eg. if the current frequency is at the old minimum, and then we reduce
the minum further we should then enable the 'down' interrupts in PMINTRMSK
but currently we don't.
Fix it up by always calling valleyview_set_rps() (just like we do for
!vlv/chv platforms). This also allows the code to be simplified a bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calls have been added to invalidate/flush DRRS whenever invalidate/flush is
called as part of frontbuffer tracking.
Apart from calls as a result of GEM tracking to fb invalidate/flush, a
call has been added to invalidate fb obj from crtc_page_flip as well. This
is to track busyness through flip calls.
The call to fb_obj_invalidate (in flip) is placed before queuing flip for this
obj.
drrs_invalidate() and drrs_flush() check for drrs.dp which would be NULL if
it was setup in drrs_enable(). This covers for the condition when DRRS is
not supported.
v2: Removing the call to invalidate_drrs from page_flip.
This has not been tested on Android yet, but, in case DRRS transtions do not
work as expected, check by adding back this call in page_flip.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calling enable/disable DRRS when enable/disable DDI are called.
These functions are responsible for setup of drrs data (in enable) and
reset of drrs (in disable).
has_drrs is true when downclock_mode is found and SEAMLESS_DRRS is set in
the VBT. A check has been added for has_drrs in these functions, to make
sure the functions go through only if DRRS will work on the platform with
the attached panel.
V2: [By Ram]: WARN_ON is used when intel_edp_drrs_enable() is called more than
once [Rodrigo]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add DRRS work function to trigger a switch to low refresh rate,
when no activity is detected on screen till 1 sec duration.
v2: [By Ram]: drrs.dp also protected with drrs.mutex and worker function
is renamed to intel_edp_drrs_downclock_work [Chris]
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Self-explanatory code is better code.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Const is good for you. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove all the trivial and/or dummy callbacks from intel dsi device
ops. Merge send_otp_cmds into panel_reset as they're called back to
back.
This will be helpful for switching to use drm_panel for the
callbacks. If we ever need the additional callbacks, we should add them
to drm_panel funcs.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Resolve tiny conflict with ongoing atomic work.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add port parameter to wait_for_dsi_fifo_empty, and call it for each dsi
port.
We can now remove the transitional intel_dsi_pipe_to_port() function.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
wait_for_dsi_fifo_empty can be static in intel_dsi.c. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This seems like the right thing to do. This also gets rid of a call to
intel_dsi_pipe_to_port() which we want to remove eventually.
v2: add braces to fix else logic (Shobhit)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of having the for each dsi port loop within dpi_send_cmd(), add
a port parameter to the function and call it for each port instead.
This is a rewrite of
commit 4510cd779e
Author: Gaurav K Singh <gaurav.k.singh@intel.com>
Date: Thu Dec 4 10:58:51 2014 +0530
drm/i915: Dual link needs Shutdown and Turn on packet for both ports
to add more flexibility in using dpi_send_cmd() for just one port as
necessary. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We set the WIZ hashing mode to 16x4 for all the other gen6+
platfotrms, so let's follow suit on VLV.
My VLV is AWOL currently so I didn't test this, but since the results
for all the other platforms agree that 16x4 is the fastest we might
assume the same holds for VLV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I ran a few tests with xonotic and synmark2 trying out the
different WIZ hashing modes on CHV. The results seem to match the
results I got with IVB/HSW when I did the similar tests on them
in the past. That is 16x4 is generally the fastest mode, 8x8 comes
next and finally 8x4. On CHV the difference between the modes is
at most ~1% in most tests. IIRC on IVB/HSW the difference was a little
bigger, but as there doesn't seem to be any real downside to 16x4
let's use it by default.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop WaDisablePwrmtrEvent:chv as it's no longer needed.
Also remove the WaSetMaskForGfxBusyness:chv note, but we still
leave the GEN6_RP_MEDIA_IS_GFX bit enabled as that's still the
recommended setting.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wa4x4STCOptimizationDisable got only implemented for BDW, but according
to the w/a database CHV needs it too, so add it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can push down the decision whether to force flushing into the
implementation since in all places that matter obj->pin_display is
accurate already. The only place where the optimization really matters
is the sw_finish_ioctl, and that already checks for obj->pin_display
on its own.
I suspect that this was simply an artifact of how
commit 2c22569bba
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Aug 9 12:26:45 2013 +0100
drm/i915: Update rules for writing through the LLC with the cpu
evolved - only v2 added the pin_display tracking.
Note that we still retain the gist of this logic from the above commit
with the explicit force argument for the low-level clflush function.
Ville noted in his review that there's a slight behavioural change in
the set_to_gtt_domain function, which now also will flush display
plane data. This opens-open the potential for userspace to start doing
buggy things by omitting the sw_finish_ioctl, which is why I've
rejected a functional equivalent patch from Ville a while ago:
http://lists.freedesktop.org/archives/intel-gfx/2013-November/036421.html
But on second consideration it's not that evil, and in any case the
justification here is more clarity, not allowing crazy userspace.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Smatch doesn't like:
struct drm_framebuffer *fb;
fb = kzalloc(sizeof(struct intel_framebuffer), GFP_KERNEL);
and warns with:
warn: struct type mismatch 'drm_framebuffer vs intel_framebuffer'
This implicit cast was correct as struct intel_framebuffer has struct
drm_framebuffer as its first member, but in case someone want to reorder
the fields for some reason, it's slightly safer to access the underlying
drm_framebuffer through intel_fb->base.
Also, having fewer static analysis warnings is a worthy goal.
Cc: kbuild@01.org
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we are hitting the WARN inside
i915_gem_object_set_cache_level() as we can now have an unbound object
in the GTT write domain (due to 43566dedde "drm/i915: Broaden
application of set-domain(GTT)"). To avoid the warning, we need to track
when we elided the clflush on a cacheable object and then evict the
cache for the object when we move the object out of a cacheable domain.
Reported-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Testcase: igt/gem_mmap_wc/set-cache-level
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88607
Tested-by: huax.lu@intel.com
[danvet: Split if into nested if as discussion on the m-l.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We increase it when we pin, so for the casual reader
rename it to cause less confusion.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We pin when we submit to execlist queue. Balance
the pinning when the submitted queue is cleaned on reset.
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will let userland only try to use the new ring
when the appropriate kernel is present
v2: change the number to be consistent with upstream (Zhipeng)
Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed--by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Skylake GT3 we have 2 Video Command Streamers (VCS), which is asymmetrical.
For example, HEVC GPU commands can be only dispatched to VCS1 ring.
But userspace has no control when using VCS1 or VCS2. This patch introduces
a mechanism to avoid the default ping-pong mode and use one specific ring
through execution flag. This mechanism is usable for all the platforms
with 2 VCS rings.
The open source usage is from these two commits in vaapi/intel:
commit 702050f04131a44ef8ac16651708ce8a8d98e4b8
Author: Zhao, Yakui <yakui.zhao@intel.com>
Date: Mon Nov 17 12:44:19 2014 +0800
Allow the batchbuffer to be submitted with override flag
commit a56efcdf27d11ad9b21664b4a2cda72d7f90f5a8
Author: Zhao Yakui <yakui.zhao@intel.com>
Date: Mon Nov 17 12:44:22 2014 +0800
Add the override flag to assure that HEVC video command
always uses BSD ring0 for SKL GT3 machine
v2: fix whitespace (Rodrigo)
v3: remove incorrect chunk that came on -collector rebase. (Rodrigo)
v4: change the comment (Zhipeng)
v5: address Daniel's comment (Zhipeng)
Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This vfunc and related structure are only used for fast boot, so let's
rename them to not take them as general purpose ones.
v2: Fix conflicts caused by the introduction of struct intel_crtc_state
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Universal planes have changed a bit the register organization.
v2: Rebase on top of the latest drm-intel-nightly
v3: Use PLANE_SIZE to retrieve the fb size (Tvrtko)
Don't use BUG() (Tvrtko)
v4: Use MISSING_CASE (Daniel)
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will have a skl_ version shortly!
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may as well try to be consistent everywhere and know the pipes by
their name.
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
crtc->plane can only be different from crtc->pipe pre-Gen4. Don't use it
in new-ish code.
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
crtc->base.primary->fb was used everywhere. Use fb to temporarily point
there and don't forget to assign fb to its final destination at the end.
v2: Rebase on top of misc changes (mask of DSPSURF, PAGE_ALIGN)
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we need to change the fb height constraints, it sounds like a good
idea to have to do it in one place only.
v2: v2: Rebase on top of Ander's "Make intel_crtc->config a pointer"
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than having "tiled" meaning "is it X-tiled?" convert the field to
explicitely store the tiling mode. The code doesn't have to change much
as 1 is conveniently I915_TILING_X.
This is to accommodate future changes around tiling modes and scannout
buffers.
v2: Rebase on top of Ander's "Make intel_crtc->config a pointer"
Reviewed-By: Tvrtko Ursulin <tvrtko.ursulin@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable coarse power gating for Gen9. This feature allows render and
media engine to enter RC6 independently. Policies are configured
together with RC6. This feature will only be enabled when RC6 is
enabled.
v2: Rebase after Chris'/Mika's forcewake change (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use the new function, gen6_init_rps_frequencies() (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per latest PM programming guide.
v2: the wrong flavour of the function updating the ring frequency was
called, leading to dead locks (Tvrtko)
v3: Add GEN6_RP_MEDIA_IS_GFX to RP_CONTROL (Imre, done by Damien)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fixup conflicts with Mika's forcewake refactor.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding new power doamins for AUX controllers
v2: Added new power domains in power_domain_str per Imre's comment
v3: Added AUX power domains to older platforms
v4: Rebase on top of POWER_DOMAIN_PLLS.
v5: Modified to address review comments from Imre
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v3)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are multiple forcewake domains in newer architectures.
Rename 'i915_gen6_forcewake_count_info' debugfs entry to
'i915_forcewake_domains' to reflect this.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the domains and domain identifiers enums. To emphasize
the difference in order to avoid mistakes.
v2: s/fw_domain/forcewake_domain (Jani)
v3: rebase
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have multiple forcewake domains now on recent gens. Change the
function naming to reflect this.
v2: More verbose names (Chris)
v3: Rebase
v4: Rebase
v5: Add documentation for forcewake_get/put
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These two were using a fw dance logic where posting read was done
after both domain bit were set. When in other gens, the posting
read is done immediately after setting the forcewake bit for each
domain.
Now bring these in line with other gens.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we now have forcewake domains, take advantage of it
by putting the differences in gen fw handling in data rather
than in code.
In past we have opencoded this quite extensively as the fw handling
is in the fast path. There has also been a lot of cargo-culted
copy'n'pasting from older gens to newer ones.
Now when the releasing of the forcewake is done by deferred timer,
it gives chance to consolidate more. Due to the frequency of actual hw
access being significantly less.
Take advantage of this and generalize the fw handling code
as much as possible. But we still aim to keep the forcewake sequence
particularities for each gen intact. So the access pattern
to fw engines should remain the same.
v2: - s/old_ack/clear_ack (Chris)
- s/post_read/posting_read (Chris)
- less polite commit msg (Chris)
v3: - rebase
- check and clear wake_count in init
v4: - fix posting reads for gen8 (PRTS)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a structure to track the individual forcewake domains and use
that to eliminate duplicate logic.
v2: - Rebase on latest dinq (Mika)
- for_each_fw_domain macro (Mika)
- Handle reset atomically, keeping the timer running (Mika)
- for_each_fw_domain parameter ordering (Chris)
- defer timer on new register access (Mika)
v3: - Fix forcewake_reset/get race by waiting pending timers
v4: - cond_resched and verbose warning on timer deletion (Chris)
- need to run pending timers manually on reset
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With gen < 6 we don't need to take uncore lock as we
don't have anything to protect from concurrent access.
v2: rebase and account for gen9 changes
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On user forcewake access, assert that runtime pm reference is held.
Fix and cleanup the callsites accordingly.
v2: Remove intel_runtime_pm_get() rebasehap (Deepak)
v3: use drivers own runtime state tracking as pm_runtime_active()
will return wrong results when we are in resume callchain (Mika)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calling intel_runtime_pm_put() is illegal from a soft-irq context, so
revert the crude hack
commit aa0b3b5bb8
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Apr 1 14:55:07 2014 -0300
drm/i915: don't schedule force_wake_timer at gen6_read
and apply the single line corrective instead.
v2: assert forcewake is off after the forcewake_reset (Paulo)
References: https://bugs.freedesktop.org/show_bug.cgi?id=80913
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move all remaining elements that were unique to execlists queue items
in to the associated request.
Issue: VIZ-4274
v2: Rebase. Fixed issue of overzealous freeing of request.
v3: Removed re-addition of cleanup work queue (found by Daniel Vetter)
v4: Rebase.
v5: Actual removal of intel_ctx_submit_request. Update both tail and postfix
pointer in __i915_add_request (found by Thomas Daniel)
v6: Removed unrelated changes
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Reformat comment with strange linebreaks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The first pass implementation of execlists required a backpointer to the context to be held
in the intel_ringbuffer. However the context pointer is available higher in the call stack.
Remove the backpointer from the ring buffer structure and instead pass it down through the
call stack.
v2: Integrate this changeset with the removal of duplicate request/execlist queue item members.
v3: Rebase
v4: Rebase. Remove passing of context when the request is passed.
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Where there were duplicate variables for the tail, context and ring (engine)
in the gem request and the execlist queue item, use the one from the request
and remove the duplicate from the execlist queue item.
Issue: VIZ-4274
v1: Rebase
v2: Fixed build issues. Keep separate postfix & tail pointers as these are
used in different ways. Reinserted missing full tail pointer update.
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a reference and pointer from the execlist queue item to the associated
gem request. For execlist requests that don't have a request, create one
as a placeholder.
Issue: VIZ-4274
v1: Rebase after upstream of "Replace seqno values with request structures" patchset.
Signed-off-by: Nick Hoath <nicholas.hoath@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that atomic operations will reference the right crtc state.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The previous patch changed the config field in intel_crtc to a pointer,
but to keep the mechanical changes (done with spatch) separate from the
new code, the pointer was made to point to a new _config field with type
struct intel_crtc_state added to that struct. This patch improves that
code by getting rid of that field, allocating a state struct in
intel_crtc_init() a keeping it properly updated when a mode set
happens.
v2: Manual changes split from previous patch. (Matt)
Don't leak the current state when the crtc is destroyed (Matt)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[danvet: Squash in fixup from Matt Roper for driver unload.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To match the semantics of drm_crtc->state, which this will eventually
become. The allocation of the memory for config will be fixed in a
followup patch. By adding the extra _config field to intel_crtc it was
possible to generate this entire patch with the cocci script below.
@@ @@
struct intel_crtc {
...
-struct intel_crtc_state config;
+struct intel_crtc_state _config;
+struct intel_crtc_state *config;
...
}
@@ struct intel_crtc *crtc; @@
-memset(&crtc->config, 0, sizeof(crtc->config));
+memset(crtc->config, 0, sizeof(*crtc->config));
@@ @@
__intel_set_mode(...) {
<...
-to_intel_crtc(crtc)->config = *pipe_config;
+(*(to_intel_crtc(crtc)->config)) = *pipe_config;
...>
}
@@ @@
intel_crtc_init(...) {
...
WARN_ON(drm_crtc_index(&intel_crtc->base) != intel_crtc->pipe);
+intel_crtc->config = &intel_crtc->_config;
return;
...
}
@@ struct intel_crtc *crtc; @@
-&crtc->config
+crtc->config
@@ struct intel_crtc *crtc; identifier member; @@
-crtc->config.member
+crtc->config->member
@@ expression E; @@
-&(to_intel_crtc(E)->config)
+to_intel_crtc(E)->config
@@ expression E; identifier member; @@
-to_intel_crtc(E)->config.member
+to_intel_crtc(E)->config->member
v2: Clarify manual changes by splitting them into another patch. (Matt)
Improve cocci script to generate even more of the changes. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In functions that define a local pipe_config variable to point to
crtc->config, replace remaining references to crtc->config with
the local variable. This makes the code more consistent and easier
to change in an automated manner.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reduces the number of direct users of crtc->new_config, opening up
the possibilty of removing it altogether.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:
@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Earlier, DRRS structures were specific to eDP (used only in intel_dp).
Since DRRS can be extended to other internal display types
(if the panel supports multiple RR), modifying structures
to be part of drm_i915_private and have a provision to add display related
structs like intel_dp.
Also, aligning with frontbuffer tracking mechanism, the new structure
contains data for busy frontbuffer bits.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV the rc6 residency calculations read a second register to
determine the actual units used for the residency value. The variable
name 'reg' where that register value is stored shadows the function
argument 'reg'. That can easily leave the reader utterly confused, so
rename the internal variable to 'clk_reg'.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
[danvet: Spellfix in commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't register the rc6p and rc6pp sysfs files on VLV, so there's no
point in having any VLV checks in them. Drop the checks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The performance regression from the CHV RC6 EI->TO change is now fixed
so re-enable TO mode for better RC6 resicency.
This reverts commit e85a5c7989.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CherryViewA0_iGfx_BIOS_DRIVER_PUNIT_spec_y14w28d5 tells us not to enable
the RP down timeout interrupt, and says that the timeout value is hence
not used. We do enable that interrupt currently though, so leaving the
timeout as 0 results in very poor performance as the GPU frequency keeps
dropping constantly. So just program the register with the recommended
value.
Leaving the interrupt enabled doesn't seem to do any harm so far. So
I've decided to leave it on for now, just to avoid making CHV a
special case.
This fixes the performance regression from:
commit 5a0afd4b78
Author: Deepak S <deepak.s@linux.intel.com>
Date: Sat Dec 13 11:43:27 2014 +0530
drm/i915/chv: Use timeout mode for RC6 on chv
Cc: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use decimal for all the other RP magic values, so change
GEN6_RP_DOWN_TIMEOUT to decimal as well. Also change the order
of the register writes to match the BIOS spec for easier verification.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the sequence in the BIOS spec and clear the RC_CONTROL register
before changing any of the other RC6/RP registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use new Sideband offset to read max/min/gaur freq based on the SKU it
is running on. Based on the Number of EU, we read different bits to
identify the max frequencies at which system can run.
v2: reuse mask definitions & INTEL_INFO() to get device info (Ville)
v3: add break in switch conditions (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like latest BSW/CHV production system has sideband address > 128.
Use u32 data types to cover new offset/address range :)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting with Cherryview, devices may have a varying number of EU for
a given ID due to creative fusing. Punit support different frequency for
different fuse data. We use this patch to help get total eu enabled and
read the right offset to get RP0
Based upon a patch from Jeff, but reworked to only store eu_total and
avoid sending info to userspace
v2: Format register definitions (Jani)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we transitioned to the atomic plane helpers in commit:
commit ea2c67bb4a
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Dec 23 10:41:52 2014 -0800
drm/i915: Move to atomic plane helpers (v9)
one of the changes was to call intel_plane_destroy_state() while tearing
down a plane to prevent leaks when unloading the driver. That made
sense when the patches were first written, but before they were merged,
commit 3009c0377f
Author: Thierry Reding <treding@nvidia.com>
Date: Tue Nov 25 12:09:49 2014 +0100
drm: Free atomic state during cleanup
had already landed, which made this the responsibility of the DRM core.
The result was that we were kfree()'ing the state twice, and also
possibly double-unref'ing a framebuffer, leading to memory corruption
when the driver was unloaded.
The fix is to simply not try to cleanup the state in the i915 teardown
code now that the core handles this for us.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88433
Testcase: igt/drv_module_reload
Root-cause-analysis-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rotation property is shared by multiple drivers, so it makes sense
to store the rotation value (for atomic-converted drivers) in the common
plane state so that core code can eventually access it as well.
Cc: dri-devel@lists.freedesktop.org
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Radeon drm-next changes for 3.20. Highlights:
- Indirect draw support for evergreen/NI hw
- SMC fan control support for SI/CI
- Manual fan control for SI/CI
- DP audio support
- Lots of code cleanup
* 'drm-next-3.20' of git://people.freedesktop.org/~agd5f/linux: (45 commits)
drm/radeon: make MMU_NOTIFIER optional
drm/radeon: use NULL rather then 0 in audio detect
drm/radeon: whitespace clean up in radeon_audio.c
radeon/audio: enable DP audio
radeon/audio: moved audio caps programming to audio_hotplug() function
radeon/audio: applied audio_dpms() and audio_mode_set() calls
radeon/audio: consolidate audio_mode_set() functions
radeon/audio: removed unnecessary debug settings
radeon/audio: moved mute programming to a separate function
radeon/audio: moved audio packet programming to a separate function
radeon/audio: set_avi_packet() function cleanup
radeon/audio: removed unnecessary CRC control programing
radeon: moved HDMI color depth programming to a separate function
radeon/audio: moved VBI packet programming to separate functions
radeon/audio: consolidate update_acr() functions (v2)
radeon/audio: consolidate update_avi_infoframe() functions
radeon/audio: consolidate audio_set_dto() functions
radeon/audio: consolidate audio_fini() functions
radeon/audio: consolidate audio_enable() functions
radeon/audio: consolidate select_pin() functions
...
This pull request includes some code refactoring which removes
Exynos specific structure names and uses generic structure
names instead, and makes all plane updating to be done
by only exynos_update_plane function. And also it includes
some cleanup and fixup patches.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (22 commits)
drm/exynos: fimd: check error status for drm_iommu_attach_device
drm/exynos: create exynos_check_plane()
drm/exynos: remove mode_set() ops from exynos_crtc
drm/exynos: don't duplicate drm_display_mode in fimd context
drm/exynos: remove struct exynos_drm_manager
drm/exynos: remove drm_dev from struct exynos_drm_manager
drm/exynos: move 'type' from manager to crtc struct
drm/exynos: remove pipe member of struct exynos_drm_manager
drm/exynos: add pipe param to exynos_drm_crtc_create()
drm/exynos: rename base object of struct exynos_drm_crtc to 'base'
drm/exynos: remove exynos_drm_crtc_mode_set_commit()
drm/exynos: call exynos_update_plane() directly on page flips
drm/exynos: unify plane update on exynos_update_plane()
drm/exynos: remove exynos_plane_commit() wrapper
drm/exynos: don't do any DPMS operation while updating planes
drm/exynos: Don't touch DPMS when updating overlay planes
drm/exynos/vidi: remove useless ops->commit()
drm/exynos/fimd: don't initialize 'ret' variable in fimd_probe()
drm/exynos: remove struct exynos_drm_overlay
drm/exynos: remove exynos_drm_crtc_plane_* wrappers
...
Here is a pull request of fixes for 3.20 patches, including the fix you asked
me when you merged the previous pull request.
* tag 'drm-amdkfd-next-fixes-2015-01-25' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: change amdkfd version to 0.7.1
drm/radeon: cik_sdma_ctx_switch_enable() can be static
drm/amdkfd: Fix sparse errors
drm/amdkfd: Handle case of invalid queue type
drm/amdkfd: Add break at the end of case
drm/amdkfd: Remove negative check of uint variable
formats and num_formats arguments were previously called fmts and nfmts.
Fix the kernel doc comment so that it matches the new argument names.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- refactor i915/snd-hda interaction to use the component framework (Imre)
- psr cleanups and small fixes (Rodrigo)
- a few perf w/a from Ken Graunke
- switch to atomic plane helpers (Matt Roper)
- wc mmap support (Chris Wilson & Akash Goel)
- smaller things all over
* tag 'drm-intel-next-2015-01-17' of git://anongit.freedesktop.org/drm-intel: (40 commits)
drm/i915: Update DRIVER_DATE to 20150117
i915: reuse %ph to dump small buffers
drm/i915: Ensure the HiZ RAW Stall Optimization is on for Cherryview.
drm/i915: Enable the HiZ RAW Stall Optimization on Broadwell.
drm/i915: PSR link standby at debugfs
drm/i915: group link_standby setup and let this info visible everywhere.
drm/i915: Add missing vbt check.
drm/i915: PSR HSW/BDW: Fix inverted logic at sink main_link_active bit.
drm/i915: PSR VLV/CHV: Remove condition checks that only applies to Haswell.
drm/i915: VLV/CHV PSR needs to exit PSR on every flush.
drm/i915: Fix kerneldoc for i915 atomic plane code
drm/i915: Don't pretend SDVO hotplug works on 915
drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV
drm/i915: Remove I915_HAS_HOTPLUG() check from i915_hpd_irq_setup()
drm/i915: Make hpd arrays big enough to avoid out of bounds access
Revert "drm/i915/chv: Use timeout mode for RC6 on chv"
drm/i915: Improve HiZ throughput on Cherryview.
drm/i915: Reset CSB read pointer in ring init
drm/i915: Drop unused position fields (v2)
drm/i915: Move to atomic plane helpers (v9)
...
Just flushing out my drm-misc branch, nothing major. Well too old patches
I've dug out from years since a patch from Rob look eerily familiar ;-)
* tag 'topic/core-stuff-2015-01-23' of git://anongit.freedesktop.org/drm-intel:
drm/probe-helper: clamp unknown connector status in the poll work
drm/probe-helper: don't lose hotplug event
next: drm/atomic: Use copy_from_user to copy 64 bit data from user space
drm: Make drm_read() more robust against multithreaded races
drm/fb-helper: Propagate errors from initial config failure
drm: Drop superfluous "select VT_HW_CONSOLE_BINDING"
check error status for drm_iommu_attach_device() and make sure
it propagates till the caller.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Inki Dae <daeinki@gmail.com>
Split update plane in two parts, an initial check part that can fail
and the update part that can't fail.
This is a important step for the upcoming atomic modesetting support.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We can safely use the mode stored in the crtc.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos_drm_manager was just a redundant struct to represent the crtc as
well. In this commit we merge exynos_drm_manager into exynos_drm_crtc to
remove an unnecessary level of indirection easing the understand of the
flow on exynos.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
manager-drm_dev is only accessed by exynos_drm_crtc_create() so this patch
pass drm_dev as argument on exynos_drm_crtc_create() and remove it from
struct exynos_drm_manager.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
'type' is now part of the struct exynos_drm_crtc. This is just another
step in the struct exynos_drm_manager removal.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
It is not longer used. This is part of the process of removing
struct exynos_drm_manager entirely.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Get the pipe value from a parameter instead of getting it from
manager->pipe. We are removing manager->pipe.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
'base' is more widely used name in the drm subsystem for the base object.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This was just as extra chain in the call stack. We just rename it to
_set_base() and let it do everything alone.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Avoid an extra call to exynos_drm_crtc_mode_set_commit() that only calls
exynos_update_plane().
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We can safely use the exynos_update_plane() to update the plane
framebuffer for both the overlay and primary planes.
Note that this patch removes a call to manager->ops->commit() in
exynos_drm_crtc_mode_set_commit(). The commit() call is used only by the
fimd driver to set underlying timings and need only in full modeset
operations. For plane update only win_commit is needed.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
It's doing nothing but calling exynos_crtc->ops->win_commit(), so let's
call this directly to avoid extra layers of abstraction.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DPMS only makes sense when the mode changes, for plane update changes do
not perform any dpms operation.
This move places the win_commit() and commit() calls directly in the code
instead of calling exynos_drm_crtc_commit() thus avoiding DPMS operations.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DPMS settings should only be changed by a full modeset.
exynos_plane_update() should only care about updating the planes itself
and nothing else.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
vidi_commit does nothing, remove it and its callers.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We set it in the beginning of the function, thus no need to set it at
initialization.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
struct exynos_drm_overlay has no practical advantage nor serves as
important piece of the exynos API design. The only place it was used
was inside the struct exynos_plane which was just causing a extra
access overhead. Users had to access the overlay first and just then
get the plane information it contains.
This patch merges struct exynos_drm_overlay into struct exynos_plane.
It also renames struct exynos_plane to struct exynos_drm_plane.
The rational is to cut one step to access plane information.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Nick Hoath