These SoCs make use of the 14nm phy, but at different
addresses than other 14nm units.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We haven't sync'd for a while.. pull in updates to get definitions for
some fields in pkt7 payloads.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On SDM845 and SC7180 DSI needs to express a performance state
requirement on a power domain depending on the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
dev_pm_opp_set_rate() is designed to be equivalent to clk_set_rate()
for devices without an OPP table, hence the change works fine
on devices/platforms which only need to set a clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
"The PM core always increments the runtime usage counter
before calling the ->suspend() callback and decrements it
after calling the ->resume() callback"
DPU and DSI are managed as runtime devices. When
suspend is triggered, PM core adds a refcount on all the
devices and calls device suspend, since usage count is
already incremented, runtime suspend was not getting called
and it kept the clocks on which resulted in target not
entering into XO shutdown.
Add changes to force suspend on runtime devices during pm sleep.
Changes in v1:
- Remove unnecessary checks in the function
_dpu_kms_disable_dpu (Rob Clark).
Changes in v2:
- Avoid using suspend_late to reset the usagecount
as suspend_late might not be called during suspend
call failures (Doug).
Changes in v3:
- Use force suspend instead of managing device usage_count
via runtime put and get API's to trigger callbacks (Doug).
Changes in v4:
- Check the return values of pm_runtime_force_suspend and
pm_runtime_force_resume API's and pass appropriately (Doug).
Changes in v5:
- With v4 patch, test cycle has uncovered issues in device resume.
On bubs: cmd tx failures were seen as SW is sending panel off
commands when the dsi resources are turned off.
Upon suspend, DRM driver will issue a NULL composition to the
dpu, followed by turning off all the HW blocks.
v5 changes will serialize the NULL commit and resource unwinding
by handling them under PM prepare and PM complete phases there by
ensuring that clks are on when panel off commands are being
processed.
Changes in v6:
- Use drm_mode_config_helper_suspend/resume() instead of legacy API
drm_atomic_helper_suspend/resume() (Doug).
Trigger runtime callbacks from the suspend/resume call to turn
off the resources.
Changes in v7:
- Add "__maybe_unused" to the functions to avoid compilation
failures. Cleanup unnecessary configs (Doug).
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Spelling out _unlocked for each and every driver is a annoying.
Especially if we consider how many drivers, do not know (or need to)
about the horror stories involving struct_mutex.
Just drop the suffix. It makes the API cleaner.
Done via the following script:
__from=drm_gem_object_put_unlocked
__to=drm_gem_object_put
for __file in $(git grep --name-only $__from); do
sed -i "s/$__from/$__to/g" $__file;
done
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20200515095118.2743122-25-emil.l.velikov@gmail.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl5lkYceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGpHQH/RJrzcaZHo4lw88m
Jf7vBZ9DYUlRgqE0pxTHWmodNObKRqpwOUGflUcWbb/7GD2LQUfeqhSECVQyTID9
N9y7FcPvx321Qhc3EkZ24DBYk0+DQ0K2FVUrSa/PxO0n7czxxXWaLRDmlSULEd3R
D4pVs3zEWOBXJHUAvUQ5R+lKfkeWKNeeepeh+rezuhpdWFBRNz4Jjr5QUJ8od5xI
sIwobYmESJqTRVBHqW8g2T2/yIsFJ78GCXs8DZLe1wxh40UbxdYDTA0NDDTHKzK6
lxzBgcmKzuge+1OVmzxLouNWMnPcjFlVgXWVerpSy3/SIFFkzzUWeMbqm6hKuhOn
wAlcIgI=
=VQUc
-----END PGP SIGNATURE-----
Merge v5.6-rc5 into drm-next
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
For a given byte clock, if VCO recalc value is exactly same as
vco set rate value, vco_set_rate does not get called assuming
VCO is already set to required value. But Due to GDSC toggle,
VCO values are erased in the HW. To make sure VCO is programmed
correctly, we forcefully call set_rate from vco_prepare.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Save pll state before dsi host is powered off. Without this change
some register values gets resetted.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
I was hitting kCFI crashes when building with clang, and after
some digging finally narrowed it down to the
dsi_mgr_connector_mode_valid() function being implemented as
returning an int, instead of an enum drm_mode_status.
This patch fixes it, and appeases the opaque word of the kCFI
gods (seriously, clang inlining everything makes the kCFI
backtraces only really rough estimates of where things went
wrong).
Thanks as always to Sami for his help narrowing this down.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: freedreno@lists.freedesktop.org
Cc: clang-built-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
the normal collection of driver updates to support new SoCs, fix incorrect
data, and convert various drivers to clk_hw based APIs.
In the core, we allow clk_ops::init() to return an error code now so that we
can fail clk registration if the callback does something like fail to allocate
memory. We also add a new "terminate" clk_op so that things done in
clk_ops::init() can be undone, e.g. free memory. We also spit out a warning now
when critical clks fail to enable and we support changing clk rates and
enable/disable state through debugfs when developers compile the kernel
themselves.
On the driver front, we get support for what seems like a lot of Qualcomm and
NXP SoCs given that those vendors dominate the diffstat. There are a couple new
drivers for Xilinx and Amlogic SoCs too. The updates are all small things like
fixing the way glitch free muxes switch parents, avoiding div-by-zero problems,
or fixing data like parent names. See the updates section below for more
details.
Finally, the "basic" clk types have been converted to support specifying
parents with clk_hw pointers. This work includes an overhaul of the fixed-rate
clk type to be more modern by using clk_hw APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting
-----BEGIN PGP SIGNATURE-----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=UjXu
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
+ sc7180 display + DSI support
+ a618 (sc7180) support
+ more UBWC (bandwidth compression) support
+ various cleanups to handle devices that use vs don't
use zap fw, etc
+ usual random cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGvv03ifuP0tp7-dmqZtr1iS=s8Vc=az8BNGtEoSMD-dkw@mail.gmail.com
LANE_CTRL register in latest version of DSI controller (v2.2)
has additional functionality introduced to enable/disable HS
signalling with default value set to enabled. To accommodate this
change, LANE_CTRL register should be read and bit wise ORed to enable
non continuous clock mode. Without this change, if register is written
directly, HS signalling will be disabled resulting in black screen.
Changes in v1:
-Update LANE_CTRL register value
Changes in v2:
-Changing commit message accordingly.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add support for v2.4.1 DSI block in the sc7180 SoC.
Changes in v1:
-Modify commit text to indicate DSI version and SOC detail(Jeffrey Hugo).
-Splitting visionox panel driver code out into a
different patch(set), since panel drivers are merged into
drm-next via a different tree(Rob Clark).
Changes in v2:
-Update commit text accordingly(Matthias Kaehlcke).
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
[cleanup subject / commit message]
Signed-off-by: Rob Clark <robdclark@chromium.org>
After commit fc0c209c14 ("clk: Allow parents to be specified without
string names") we can use DT or direct clk_hw pointers to specify
parents. Create a generic function that shouldn't be used very often to
encode the multitude of ways of registering a mux clk with different
parent information. Then add a bunch of wrapper macros that only pass
down what needs to be passed down to the generic function to support
this with less arguments.
Note: the msm drm driver passes an anonymous array through the macro
which seems to confuse my compiler. Adding a parenthesis around the
whole thing at the call site seems to fix it but it must be wrong. Maybe
it's better to split this patch and pick out the array bits there?
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190830150923.259497-11-sboyd@kernel.org
Decouple enable and rate setting. Prep work to handle bootloader
enabled display.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
At the moment, the MSM DSI driver calls drm_panel_enable() rather early
from the DSI bridge pre_enable() function. At this point, the encoder
(e.g. MDP5) is not enabled, so we have not started transmitting
video data.
However, the drm_panel_funcs documentation states that enable()
should be called on the panel *after* video data is being transmitted:
The .prepare() function is typically called before the display controller
starts to transmit video data. [...] After the display controller has
started transmitting video data, it's safe to call the .enable() function.
This will typically enable the backlight to make the image on screen visible.
Calling drm_panel_enable() too early causes problems for some panels:
The TFT LCD panel used in the Samsung Galaxy Tab A 9.7 (2015) (APQ8016)
uses the MIPI_DCS_SET_DISPLAY_BRIGHTNESS command to control
backlight/brightness of the screen. The enable sequence is therefore:
drm_panel_enable()
drm_panel_funcs.enable():
backlight_enable()
backlight_ops.update_status():
mipi_dsi_dcs_set_display_brightness(dsi, bl->props.brightness);
The panel seems to silently ignore the MIPI_DCS_SET_DISPLAY_BRIGHTNESS
command if it is sent too early. This prevents setting the initial brightness,
causing the display to be enabled with minimum brightness instead.
Adding various delays in the panel initialization code does not result
in any difference.
On the other hand, moving drm_panel_enable() to dsi_mgr_bridge_enable()
fixes the problem, indicating that the panel requires the video stream
to be active before the brightness command is accepted.
Therefore: Move drm_panel_enable() to dsi_mgr_bridge_enable() to
delay calling it until video data is being transmitted.
Move drm_panel_disable() to dsi_mgr_bridge_disable() for similar reasons.
(This is not strictly required for the panel affected above...)
Tested-by: Jasper Korten <jja2000@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuXvWqAysSYEJGuVH/lWMcqZwE8MFAl34lkkACgkQ/lWMcqZw
E8M76g//WRYl9fWnV063s44FBVJYjGxaus0vQJSGidaPCIE6Ep6TNjXp8DVzV82M
HR79P9glL02DC9B8pflioNNXdIRGSVk/FJcKVB2seFAqEFCAknvWDM/X/y+mOUpp
fUeFl+Znlwx3YlM8f4Qujdbm+CbTewfbya4VAWeWd8XG2V8jfq5cmODPPlUMNenZ
J6Ja+W3ph741uSIfAKaP69LVJgOcuUjXINE4SWhRk/i5QF3GIRej/A7ZjWGLQ/t2
2zUUF7EiCzhPomM40H3ddKtXb4ZjNJuc5pOD4GpxR8ciNbe2gUOHEZ5aenwYBdsU
5MwbxNKyMbKXATtn3yv3fSc4jH3DtmEKpmovONeO8ZDBrQBnxeYa3tQvfkNghA2f
acoZMzYUImV+ft6DMIgpXppASvo7mQYDAbLPOGEJ9E44AL4UP00jesEjnK5FOHSR
3BEzGUnK/6QL5zFNPni8YZQ8dan4jDIno1mqIV+cQ4WCGlaKckzIWO6243Bf13b/
kROSJpgWkiK6Ngq0ofhD0MHyT/m1QnqUzWRKTJhRtPflSWRBsDZqWCQ5Vx1QlNIE
/HfTNbTpXWwa+5wXbbB8TkDw5t9cQGnR+QcrEd9HgoIec7B5Re8rx9i0TJAT4N05
03RCQCecSfD8gwKd2wgaFIpFGRl9lTdLYSpffSmyL2X5a20lZhM=
=b15X
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-12-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
+ OCMEM support to enable the couple generations that had shared OCMEM
rather than GMEM exclusively for the GPU (late a3xx and I think basically
all of a4xx). Bjorn and Brian decided to land this through the drm
tree to avoid having to coordinate merge requests.
+ a510 support, and various associated display support
+ the usual misc cleanups and fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CAF6AEGv-JWswEJRxe5AmnGQO1SZnpxK05kO1E29K6UUzC9GMMw@mail.gmail.com
MSM8976, MSM8976 and APQ variants have DSI version 3:10040002
(DSI 6G V1.4.2), featuring two DSIs.
They need three clocks (mdp_core, iface, bus), one GDSC and
two vregs, VDDA at 1.2V and VDDIO at 1.8V.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The 28nm PLL has a different iospace on MSM/APQ family B SoCs:
add a new configuration and use it when the DT reports the
"qcom,dsi-phy-28nm-hpm-fam-b" compatible.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The DSI PHY regulator supports two regulator modes: LDO and DCDC.
This mode can be selected using the "qcom,dsi-phy-regulator-ldo-mode"
device tree property.
However, at the moment only the 20nm PHY driver actually implements
that option. Add a check in the 28nm PHY driver to program the
registers correctly for LDO mode.
Tested-by: Nikita Travkin <nikitos.tr@gmail.com> # l8150
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191023165617.28738-1-stephan@gerhold.net
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl2su/AeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvm4H/1jkheCrvB/GJS69
wd18vizAg+eFmNCzxlGVhpQTKGymNRy+g6clnoli3cNJ3pSVKcYgVyB3oXaONIhp
g/ANudnBjTdjqYgJzfLij5AGecrGwDpF3YL0kuKrCB63s2I/HwQGYy/aPrYY8emy
gAYdaf1DGRu5/DIIB6soTo/TnpKoAyTE+XY5MaPSug++t/Flov19tlU40IZxXW94
bjTXbm0yklrsIx+LL5mYYGGnygSTCF66JjFg1qhDCBQaS2MZ21h1ZgaOtGZTwZcc
WgEiqLC5S1Iyj96zir1t78RcVQ4RzgvDbhUOgIqUFsYAO2wOicvxyFE3Hj8rPOKd
uGgVPRM=
=xgZa
-----END PGP SIGNATURE-----
Merge v5.4-rc4 into drm-next
Thierry needs fd70c7755b ("drm/bridge: tc358767: fix max_tu_symbol
value") to be able to merge his dp_link patch series.
Some adjacent changes conflicts, plus some clashes in i915 due to
cherry-picking and git trying to be helpful and leaving both versions
in.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP. This is because the reset
logic is not correct per the hardware documentation.
The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.
wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes. Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.
Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Cc: Hai Li <hali@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
[seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/msm/dsi/dsi_host.c: In function dsi_cmd_dma_rx:
drivers/gpu/drm/msm/dsi/dsi_host.c:1302:7: warning: variable lp set but not used [-Wunused-but-set-variable]
It is not used since commit a689554ba6 ("drm/msm:
Initial add DSI connector support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1570690506-83287-5-git-send-email-zhengbin13@huawei.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c: In function msm_dsi_dphy_timing_calc_v2:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c:156:17: warning: variable lpx set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c: In function msm_dsi_dphy_timing_calc_v3:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c:273:17: warning: variable lpx set but not used [-Wunused-but-set-variable]
'lpx' in msm_dsi_dphy_timing_calc_v2 is not used since commit a4df68fa23
("drm/msm/dsi: Add new method to calculate 14nm PHY timings")
'lpx' in msm_dsi_dphy_timing_calc_v3 is not used since commit f1fa7ff440
("drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1570690506-83287-4-git-send-email-zhengbin13@huawei.com
Move the static keyword to the front of declarations
of msm_dsi_v2_host_ops, msm_dsi_6g_host_ops and
msm_dsi_6g_v2_host_ops, and resolve the following
compiler warnings that can be seen when building
with warnings enabled (W=1):
drivers/gpu/drm/msm/dsi/dsi_cfg.c:150:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
drivers/gpu/drm/msm/dsi/dsi_cfg.c:161:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
drivers/gpu/drm/msm/dsi/dsi_cfg.c:172:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
We haven't done any backmerge for a while due to the merge window, and it
starts to become an issue for komeda. Let's bring 5.4-rc1 in.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
clk_get_parent returns an error pointer upon failure, not NULL. So the
checks as they exist won't catch a failure. This patch changes the
checks and the return values to properly handle an error pointer.
Fixes: c4d8cfe516 ("drm/msm/dsi: add implementation for helper functions")
Cc: Sibi Sankar <sibis@codeaurora.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The following errors show up when booting the Nexus 5:
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_regulator_init: failed to init regulator, ret=-517
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_driver_probe: failed to init regulator
dsi_phy_regulator_init() already logs the error, so no need to log
the same error a second time in dsi_phy_driver_probe(). This patch
also changes dsi_phy_regulator_init() to not log the error if the
error code is -EPROBE_DEFER to reduce noise in dmesg.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[add some {}'s]
Signed-off-by: Rob Clark <robdclark@chromium.org>
This DSI driver uses the new descriptor API so these old
GPIO API includes are surplus.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop the deprecated drmP.h header file, and trim msm_drv.h
to the relevant include files.
This resulted in a suprisingly many edits as many files relied
on headers included via msm_drv.h.
But msm_drv.h is not supposed to carry include files it do not need, so
the individual files have to include what extra they needs.
v2:
- Rebased on top of https://gitlab.freedesktop.org/drm/msm.git msm-next
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Bruce Wang <bzwang@chromium.org>
Cc: Shayenne Moura <shayenneluzmoura@gmail.com>
Cc: Mamta Shukla <mamtashukla555@gmail.com>
Cc: Jonathan Marek <jonathan@marek.ca>
Cc: Carsten Behling <carsten.behling@googlemail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Cc: Sibi Sankar <sibis@codeaurora.org>
Cc: Todor Tomov <todor.tomov@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190804065551.GA5211@ravnborg.org
We are about to add a drm_bridge_state that inherits from
drm_private_state which is defined in drm_atomic.h. Problem is,
drm_atomic.h includes drm_crtc.h which in turn includes drm_bridge.h,
leading to "drm_private_state has incomplete type" error.
Let's force all users of the drm_bridge API to explicitly include
drm_bridge.h.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826152649.13820-2-boris.brezillon@collabora.com
+ usual progress on cleanups
+ dsi vs EPROBE_DEFER fixes
+ msm8998 (snapdragon 835 support)
+ a540 gpu support (mesa support already landed)
+ dsi, dsi-phy support
+ mdp5 and dpu interconnect (bus/memory scaling) support
+ initial prep work for per-context pagetables (at least the parts that
don't have external dependencies like iommu/arm-smmu)
There is one more patch for fixing DSI cmd mode panels (part of a set of
patches to get things working on nexus5), but it would be conflicty with
1cff7440a8 in drm-next without rebasing or back-merge,
and since it doesn't conflict with anything in msm-next, I think it best
if Sean merges that through drm-mix-fixes instead.
(In other news, I've been making some progress w/ getting efifb working
properly on sdm850 laptop without horrible hacks, and drm/msm + clk stuff
not totally falling over when bootloader enables display and things are
already running when driver probes.. but not quite ready yet, hopefully
we can post some of that for 5.4.. should help for both the sdm835 and
sdm850 laptops.)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsj3N4XzDLSDoa+4RHZ9wXObYmhcep0M3LjnRg48BeLvg@mail.gmail.com
Now that the panel probe/setup is in the modeset path, we can call
dsi_manager_setup_encoder() in a common place for both internal and
external bridge setups.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-10-sean@poorly.run
Since deferred probe from the modeset init path now works, we can move
the panel initialization from detect() into connector init. This
avoids doing work in detect() and hopefully will result in a more
deterministic boot sequence between devices with a dsi panel, and those
with an external bridge.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-9-sean@poorly.run
It's a bit dangerous to store the flags in msm_dsi since there's no way to
tell when they're populated. Fortunately the only place that uses them
is the same place that fills them. So just use a local variable and
delete the struct member.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-5-sean@poorly.run
The 10nm pll driver didn't have any failure-path cleanup in register,
and the destroy function didn't unregister any of the hardware. This
patch adds both.
The reason things haven't been blowing up horribly is that msm_drv has a
reference count issue that keeps devices alive, so the destroy function
was never called. That will be fixed in a follow-up patch.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-1-sean@poorly.run
Clang warns:
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: warning: logical not is
only applied to the left hand side of this bitwise operator
[-Wlogical-not-parentheses]
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^ ~
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
after the '!' to evaluate the bitwise operator first
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
around left hand side expression to silence this warning
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
1 warning generated.
Add parentheses around the bitwise AND so it is evaluated first then
negated.
Fixes: 3dbbf8f09e ("drm/msm/dsi: Add old timings quirk for 10nm phy")
Link: https://github.com/ClangBuiltLinux/linux/issues/547
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
When panel probe happens after DSI probe, the DSI probe is deferred as
per current design. In the probe defer path dsi device is destroyed.
This NULL dsi device could be deferenced by the panel probe in the
mipi_dsi_attach path.
Check for NULL dsi device before accessing it.
Changes in v2:
- Add more comments on how this NULL pointer situation will be hit
Reported-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The DSI controller on the MSM8998 SoC is a 6G v2.0.0 controller which is
very similar to the v2.0.1 of SDM845.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The v3.0.0 10nm phy has two different implementations between MSM8998 and
SDM845, which require different timings calculations. Unfortunately, the
hardware designers did not choose to revise the version to account for this
delta so implement a quirk instead.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The MSM8998 dsi phy is 10nm v3.0.0 like SDM845, however there appear to
be minor differences such as the address space location.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
wait_for_completion_timeout() returns 0 on timeout and aleast 1 otherwise
so checking for < makes no sense here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXD+OHgAKCRDj7w1vZxhR
xe3IAP4s59sFVMZseVJpwSe41OJ1ipD/cyIbtXU94X6nFd6zCAD+Jm4q+XIIS+uv
7ElmJ2BD7rwicqSViWNG8tteHYfjrAU=
=XPsb
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
[airlied: patch rcar-du to add drm_modes.h]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190116200428.u2n4jbk4mzza7n6e@flea
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-next has been forwarded to 5.0-rc1, and we need it to apply the damage
helper for dirtyfb series from Noralf Trønnes.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Fix the dsi clock names in the DSI 10nm PLL driver to
match the names in the dispcc driver as those are
according to the clock plan of the chipset.
Changes in v2:
- Update the clock diagram with the new clock name
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For debugging purposes it is useful to assign descriptions
to buffers so that we know what they are used for. Add
a field to the buffer object and use that to name the various
kernel side allocations which ends up looking like like this
in /d/dri/X/gem:
flags id ref offset kaddr size madv name
00040000: I 0 ( 1) 00000000 0000000070b79eca 00004096 memptrs
vmas: [gpu: 01000000,mapped,inuse=1]
00020000: I 0 ( 1) 00000000 0000000031ed4074 00032768 ring0
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a reference count to track how many times a particular
chunk of iova memory is pinned (mapped) in the iomu and
add msm_gem_unpin_iova to give up references.
It is important to note that msm_gem_unpin_iova replaces
msm_gem_put_iova because the new implicit behavior
that an assigned iova in a given vma is now valid for the
life of the buffer and what we are really focusing on is
the use of that iova.
For now the unmappings are lazy; once the reference counts
go to zero they *COULD* be unmapped dynamically but that
will require an outside force such as a shrinker or
mm_notifiers. For now, we're just focusing on getting
the counting right and setting ourselves up to be ready
for the future.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a new function to get and pin the iova memory in one
step (basically renaming the old msm_gem_get_iova function)
and switch msm_gem_get_iova() to only allocate an iova but
not map it in the IOMMU. This is only currently used by
msm_ioctl_gem_info() since all other users of of the iova
expect that the memory be immediately available.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use DRM_DEV_INFO/ERROR/WARN instead of dev_info/err/debug to generate
drm-formatted specific log messages so that it will be easy to
differentiate in case of multiple instances of driver.
Signed-off-by: Mamta Shukla <mamtashukla555@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currenty the VCO rate in the 10nm PLL driver relies
on the parent rate which is not configured.
Configure the VCO rate to 19.2 Mhz as required by
the 10nm PLL driver.
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If there is no bridge or panel connected to a dsi node, don't fail the
entire msm bind. Just ignore the dsi block and move on.
Cc: Doug Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If dt parsing fails, we should return an error instead of pretending
everything completed successfully.
Cc: Doug Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently msm_dsi->id is initialized to 0 during kzalloc. If bind fails
for a secondary dsi device before its id can be properly set (such as
during dt parsing), the id will point to the primary dsi device, causing
its reference to be removed from dsi_manager's global (msm_dsim_glb)
array.
This patch initializes the id to -1 and checks for negative in the
manager cleanup.
Cc: Doug Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This fixes up a collision between introducing dual-channel support and
the dsi refactors. This patch applies the same dual-channel
considerations and pclk calculations to both v2 and 6G, with a bit of
abstracting for good measure.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make the pclk_rate u64 to accommodate higher pixel clock
rates.
Changes in v3:
- Converted pclk_rate to u32 (Archit)
- Rebase on dsi cleanup set in msm-next
Cc: Sibi Sankar <sibis@codeaurora.org>
Cc: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently, DRM bridge for DPU relies on the default video
mode setting to set the encoder mode.
Add an explicit call to set the encoder mode for bridges.
Changes in v3:
- None
Reviewed-by: Archit Taneja <architt@codeauorora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
postdiv_lock spinlock was used before initialization
for 10nm pll. It causes following spin_bug:
"BUG: spinlock bad magic on CPU#0".
Initialize spinlock before its usage.
Changes in v3:
- Added Archit's R-b
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Current DSI driver uses two connectors for dual DSI case even
though we only have one panel. Fix this by implementing one
connector/bridge for dual DSI use case. Use master DSI
controllers to register one connector/bridge.
Changes in v3:
- None
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
[seanpaul removed unused local var causing a build warning]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For dual dsi mode, the horizontal timing needs
to be divided by half since both the dsi controllers
will be driving this panel. Adjust the pixel clock and
DSI timing accordingly.
Changes in v3:
- Added Archit's R-b
- Rebase on dsi cleanup set in msm-next
Cc: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Replace version checks with the helper functions bound to
cfg_handler for DSI v2, DSI 6G 1.x and DSI 6G v2.0+ controllers
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add dsi host helper function implementation for DSI v2
DSI 6G 1.x and DSI 6G v2.0+ controllers
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add dsi host helper functions support for DSI v2 and DSI 6G 1.x
controllers that are under version checks
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since there's very few callers of these I've decided to do them all in
one patch. With this the unecessarily long drm_mode_connector_ prefix
is gone from the codebase! The only exception being struct
drm_mode_connector_set_property, which is part of the uapi so can't be
renamed.
Again done with sed+some manual fixups for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-8-daniel.vetter@ffwll.ch
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
This patch avoids dereferencing msm_host->dev when it is NULL.
If we find ourselves tearing down dsi before calling
(mdp4|mdp5|dpu)_kms_init(), we'll end up in a state where the dev
pointer is NULL and trying to extract priv from it will fail.
This was introduced in a seemingly innocuous commit to ensure the
arguments to msm_gem_put_iova() are correct (even though that
function has been a stub for ~5 years). Correctness FTW! \o/
Fixes: b01884a286b0 drm/msm: use correct aspace pointer in msm_gem_put_iova()
Cc: Daniel Mack <daniel@zonque.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Even though msm_gem_put_iova() is currently a NOP function, the caller
should pass in the address space pointer it used to obtain the object.
Other call sites were changed in 8bdcd949bb ("drm/msm: pass
address-space to _get_iova() and friends"), but this one seems to have
been forgotten.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This regression stems from 0e08270a1f ("drm/msm: Separate locking of
buffer resources from struct_mutex").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Rob Clark <rclark@redhat.com>
Fixes: 0e08270a1f ("drm/msm: Separate locking of buffer resources from struct_mutex")
Signed-off-by: Rob Clark <robdclark@gmail.com>
The function dsi_get_cmd_fmt returns enum dsi_cmd_dst_format,
use the correct enum value also for MIPI_DSI_FMT_RGB666/_PACKED.
This has been discovered using clang:
drivers/gpu/drm/msm/dsi/dsi_host.c:743:35: warning: implicit conversion
from enumeration type 'enum dsi_vid_dst_format' to different
enumeration type 'enum dsi_cmd_dst_format' [-Wenum-conversion]
case MIPI_DSI_FMT_RGB666: return VID_DST_FORMAT_RGB666;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the DSI PHY timings are hard-coded for a specific panel
for the 10nm PHY.
Replace this with the auto PHY timing calculator which can calculate
the PHY timings for any panel.
Changes in v4:
- None
Changes in v3:
- None
Changes in v2:
- None
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make sure the video mode engine is on before waiting
for the video done interrupt.
Changes in v4:
- Move setting enabled to false earlier
Changes in v3:
- Move the return value check to another
patch
Changes in v2:
- Replace pr_err with dev_err
- Changed error message
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Check for the return value of wait for video
done waits and print appropriate error message.
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This should be using drm_gem_object_put(). Also since this is done only
in driver unload path, we don't need to synchronize setting tx_gem_obj
to NULL, so juse use the _unlocked() variant.
Signed-off-by: Rob Clark <robdclark@gmail.com>
_dev_ is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after _dev_ has been
null checked.
Fixes: d4e7f38d70ef ("drm/msm/dsi: check msm_dsi and dsi pointers before use")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Newer DSI host controllers (SDM845 in particular) require a new clock
called byte_intf_clk. A recent patch tried to add this as an optional
clock, but it still set 'ret' to an error number if it didn't find it.
This breaks the host's probe for all previous DSI host versions.
Instead of setting this up as an optional clock, try to get the clock
only for the DSI version that supports it.
Fixes: 56558fb ("drm/msm/dsi: Add byte_intf_clk")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI6G v2.0+ blocks have a new clock input to them called
byte_intf_clk. It's rate is to be set as byte_clk / 2.
Within the clock controller (CC) subsystem, this clock is a
child/descendant of the byte_clk.
Set it up as an optional clock in the DSI host driver. Make sure
that we enable/set its rate only after we configure byte_clk.
This is required for the ancestor clocks in the CC to be
configured correctly.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SDM845 contains 2 DSI6G v2.2.1 host controllers. Add them in dsi_cfg.
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We try to get the interface clock in dsi_get_config early during DSI's
component bind. Try getting both the "iface" and "iface_clk" clock name
variants so that we are compatible with both new and legacy DT.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate the PHY ops with the downstream driver as reference.
There are a couple of TODOs which need to be resolved:
- The PHY timings are all hardcoded for now. This needs to be replaced
with automatic calculations once we get/understand them.
- There are some lane configuration registers which use a new
representation between physical and logical lane mappings. For now,
we've hardcoced them to follow the default mapping (i.e
logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate PLL clock ops from downstream. This contains the VCO PLL
ops and the registration of standard clk_divider and clk_mux clocks.
Unlike 14nm PLL, the postdividers/mux of the slave PLL doesn't need
to be set to the same values of the postdivs/mux of the master PLL.
Hence, we don't need special postdivider clock ops like we did with
the 14nm PLL driver.
Like the previous PLL drivers, the implementation is slightly different
from downstream. We don't use shadow clocks, but have the ability to
reparent the RCGs to a different source.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move null checks of pointer arguments to the beginning of the
modeset init function since they are referenced immediately
instead of after they have already been used.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Check DSI instance id argument against the proper boundary size
to protect against invalid configuration of the DSI id.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make msm_dsi_pll_init consistently return an error code instead
of NULL when pll initialization fails so that later pll
retrieval can check against an error code. Add checks for these
failures after retrieval of src_pll to avoid invalid pointer
dereferences later in msm_dsi_pll_get_clk_provider.
Signed-off-by: Lloyd Atkinson <latkinso@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Konrad Dybcio