The driver can match by multiple methods. Its of_device_id table is
referenced via of_match_ptr() so it will be unused for !CONFIG_OF
builds:
sound/soc/codecs/tlv320aic23-i2c.c:38:34: warning: ‘tlv320aic23_of_match’ defined but not used [-Wunused-const-variable=]
sound/soc/codecs/tlv320adcx140.c:1076:34: warning: ‘tlv320adcx140_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201125164452.89239-32-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to configure the GPIO pin to the specific configuration.
The GPIO pin can be configured as GPO, IRQ, SDOUT2, PDMCLK, MICBASE_EN,
GPI, MCLK, SDIN, PDMDIN1, PDMDIN2, PDMDIN3 or PDMDIN4 and the output
drive can be configured with various configuration.
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200918114025.18205-2-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add code to allow the ASI Tx output to be placed into High-z mode
during unused ASI cycles. This allows for other devices that may be on
the bus to drive the ASI out. By default the 320adcx140 sends 0's for
unused cycles.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the BCLK inversion for DSP modes
This is how it is defined by ASoC:
* BCLK:
* - "normal" polarity means signal is available at rising edge of BCLK
* - "inverted" polarity means signal is available at falling edge of BCLK
The adcx140 defines the BCLK edge based on coding type.
The PCM (DSP_A/B) should drive on rising and sample on falling edge, so
from ASoC pov, it is IB_NF. But from the codec pov if it is configured in
DSP mode, then the BCLK should not be inverted, defaults to the coding
standard.
For i2s, it is NB_NF from ASoC pov (drive on falling, sample on rising).
>From the codec's pov BCLK should not invert either, as this is the default
for the coding.
So, inversion must take the format into account:
IB_NF + DSP_A/B == the codec bclk inversion should be disabled
NB_NF + DSP_A/B == the codec bclk inversion should be enabled
NB_NF + I2S == the codec bclk inversion should be disabled
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It was observed that if the device was active and register writes were
performed there were some unwanted behaviors particularly when writing
the word length and some filter options. So when writing to the device
the device should be placed in sleep mode and then exit sleep mode once
the register update is complete.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its datasheet, the digital gain should be -100 dB when
CHx_DVOL is 1 and 27 dB when CHx_DVOL is 255. But with the current
dig_vol_tlv, "Digital CHx Out Volume" shows 27.5 dB if CHx_DVOL is 255
and -95.5 dB if CHx_DVOL is 1. This commit fixes this bug.
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200908090417.16695-1-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its datasheet, after reset this codec goes into sleep
mode. In this mode, any register accessing should be avoided except for
exiting sleep mode. Hence this commit moves SLEEP_CFG access before any
register accessing.
Signed-off-by: Camel Guo <camelg@axis.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200908083521.14105-2-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In adcx140_i2c_probe, adcx140->dev is accessed before its
initialization. This commit fixes this bug.
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20200901135736.32036-1-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the audio routing map to enable the digital mic paths when the
analog mic paths are not enabled.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200828112855.10112-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reset the device before programming the registers or all programming
will be lost as the device resets registers to default settings.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200730142419.28205-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The header was updated to align with the data sheet to start the GPO_CFG
at GPO_CFG0. The code was not updated to the change and therefore the
GPO_CFG0 register was not written to.
Fixes: 6617cff6a0 ("ASoC: tlv320adcx140: Add GPO configuration and drive output config")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200730142419.28205-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add General Purpose Output (GPO) configuration and driver output
configuration. The GPOs can be configured as a GPO, IRQ, SDOUT or a
PDMCLK output. In addition the output drive can be configured with
various configurations.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200728160833.24130-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix white space issues and remove else case where it was not needed.
Convert "static const char *" to "static const char * const"
Fixes: 689c7655b5 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200728164339.16841-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719153822.59788-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the TX offset slot programming. There is no RX offset slot
register.
Since there is no RX offset the check for slot symmetry can be removed.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200709185129.10505-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the warnings when using the W=1 compiler flag.
sound/soc/codecs/tlv320adcx140.c: In function ‘adcx140_reset’:
sound/soc/codecs/tlv320adcx140.c:570:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
570 | int ret = 0;
| ^~~
This was set but only used in case where the reset GPIO is not defined.
Have the function return the value of ret.
sound/soc/codecs/tlv320adcx140.c: In function ‘adcx140_codec_probe’:
sound/soc/codecs/tlv320adcx140.c:778:18: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
778 | if (bias_source < ADCX140_MIC_BIAS_VAL_VREF ||
| ^
sound/soc/codecs/tlv320adcx140.c:789:18: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
789 | if (vref_source < ADCX140_MIC_BIAS_VREF_275V ||
This condition will not occur since if the dt property is not set then
the *_source variable is set to the default value. So there is no way
that *_source can be less then 0. Which is what each #define is set to.
The code just needs to make sure that the dt property is not out of the
upper bounds.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200526175247.15309-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to configure the GPI pins to the specific configuration.
The pins can be disabled or be configured as data input for any of the
digital mic channels. In addition the GPI can be used a a general
purpose input, a Master clock input or an ASI input for daisy chaining
devices.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200526200917.10385-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add ALSA controls to configure the PDM clocks.
The clocks need to be configurable to accommodate various microphones
that use clocks for low power/low resolution modes to high power/high
resolution modes.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200514123338.20392-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The device tree binding declares the ti,mic-bias-source and the
ti,vref-source properties as u32. The code reads them as u8 which is
incorrect. Since the device tree binding indicates them as u32 the
conde needs to be updated to read u32.
In addition the bias source needs to be shifted 4 bits to
correctly write the register.
driver family")
Fixes: 37bde5acf040 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200513142807.11802-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the mic gain registers for channels 2-4.
The incorret register was being set as it was touching the CH1 config
registers.
Fixes: 37bde5acf040 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200427203608.7031-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the range verification check for the mic_bias and vref device tree
entries.
Fixes 37bde5acf040 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec driver family")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200304193427.16886-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add decimation filter selection support.
Per Section 8.3.6.7 the Digital Decimation Filter is selectable between
a Linear Phase, Low Latency, and Ultra Low Latency filer.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200221181358.22526-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320ADCx140 parts support Dynamic Range Enhancer (DRE) as defined
in Section 8.3.2 of the data sheets.
The DRE achieves a complete-channel dynamic range as high as 120 dB.
At a system level, the DRE scheme enables far-field, high-fidelity recording
of audio signals in very quiet environments and low-distortion recording in
loud environments.
There are 2 enables for DRE. The first is a global setting that enables
the DRE engine in the device and the other enable is per channel. If
the DRE is enabled globally then either DRE or AGC can be used per each
configured channel. If global DRE is disabled then even setting the DRE
enable bit in the channel config register will have no effect.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200221181358.22526-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the tlv320adcx140 codec driver family.
The TLV320ADCx140 is a Burr-Brown™ highperformance, audio analog-to-digital
converter (ADC) that supports simultaneous sampling of up to four analog
channels or eight digital channels for the pulse density modulation (PDM)
microphone input. The device supports line and microphone inputs, and
allows for both single-ended and differential input configurations.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200220210759.31466-3-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuninori Morimoto