Like ipv4, we have to propagate the ipv6 route peer into
the ipsec top-level route during instantiation.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that causes TCP RST packets to be generated
on otherwise correctly behaved applications, e.g., no unread data
on close,..., etc. To trigger the bug, at least two conditions must
be met:
1. The FIN flag is set on the last data packet, i.e., it's not on a
separate, FIN only packet.
2. The size of the last data chunk on the receive side matches
exactly with the size of buffer posted by the receiver, and the
receiver closes the socket without any further read attempt.
This bug was first noticed on our netperf based testbed for our IW10
proposal to IETF where a large number of RST packets were observed.
netperf's read side code meets the condition 2 above 100%.
Before the fix, tcp_data_queue() will queue the last skb that meets
condition 1 to sk_receive_queue even though it has fully copied out
(skb_copy_datagram_iovec()) the data. Then if condition 2 is also met,
tcp_recvmsg() often returns all the copied out data successfully
without actually consuming the skb, due to a check
"if ((chunk = len - tp->ucopy.len) != 0) {"
and
"len -= chunk;"
after tcp_prequeue_process() that causes "len" to become 0 and an
early exit from the big while loop.
I don't see any reason not to free the skb whose data have been fully
consumed in tcp_data_queue(), regardless of the FIN flag. We won't
get there if MSG_PEEK is on. Am I missing some arcane cases related
to urgent data?
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.
To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts the following set of commits:
d1ed113f16 ("ipv6: remove duplicate neigh_ifdown")
29ba5fed1b ("ipv6: don't flush routes when setting loopback down")
9d82ca98f7 ("ipv6: fix missing in6_ifa_put in addrconf")
2de7957072 ("ipv6: addrconf: don't remove address state on ifdown if the address is being kept")
8595805aaf ("IPv6: only notify protocols if address is compeletely gone")
27bdb2abcc ("IPv6: keep tentative addresses in hash table")
93fa159abe ("IPv6: keep route for tentative address")
8f37ada5b5 ("IPv6: fix race between cleanup and add/delete address")
84e8b803f1 ("IPv6: addrconf notify when address is unavailable")
dc2b99f71e ("IPv6: keep permanent addresses on admin down")
because the core semantic change to ipv6 address handling on ifdown
has broken some things, in particular "disable_ipv6" sysctl handling.
Stephen has made several attempts to get things back in working order,
but nothing has restored disable_ipv6 fully yet.
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a conflict between commit b00916b1 and a77f5db3. This patch resolves
the conflict by clearing the heap allocation in ethtool_get_regs().
Cc: stable@kernel.org
Signed-off-by: Eugene Teo <eugeneteo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not handle PMTU vs. route lookup creation any differently
wrt. offlink routes, always clone them.
Reported-by: PK <runningdoglackey@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE get/set app handlers use generic routines and do not
require the net_device to implement the dcbnl_ops routines. This
patch makes it symmetric so user space and drivers do not have
to handle the CEE version and IEEE DCBx versions differently.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a8b690f98b (tcp: Fix slowness in read /proc/net/tcp)
introduced a bug in handling of SYN_RECV sockets.
st->offset represents number of sockets found since beginning of
listening_hash[st->bucket].
We should not reset st->offset when iterating through
syn_table[st->sbucket], or else if more than ~25 sockets (if
PAGE_SIZE=4096) are in SYN_RECV state, we exit from listening_get_next()
with a too small st->offset
Next time we enter tcp_seek_last_pos(), we are not able to seek past
already found sockets.
Reported-by: PK <runningdoglackey@yahoo.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Family was hard-coded to AF_INET but should be daddr->family.
This fixes crashes when unlinking ipv6 peer entries, since the
unlink code was looking up the base pointer properly.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppose that several linear skbs of the same flow were received by GRO. They
were thus merged into one skb with a frag_list. Then a new skb of the same flow
arrives, but it is a paged skb with data starting in its frags[].
Before adding the skb to the frag_list skb_gro_receive() will of course adjust
the skb to throw away the headers. It correctly modifies the page_offset and
size of the frag, but it leaves incorrect information in the skb:
->data_len is not decreased at all.
->len is decreased only by headlen, as if no change were done to the frag.
Later in a receiving process this causes skb_copy_datagram_iovec() to return
-EFAULT and this is seen in userspace as the result of the recv() syscall.
In practice the bug can be reproduced with the sfc driver. By default the
driver uses an adaptive scheme when it switches between using
napi_gro_receive() (with skbs) and napi_gro_frags() (with pages). The bug is
reproduced when under rx load with enough successful GRO merging the driver
decides to switch from the former to the latter.
Manual control is also possible, so reproducing this is easy with netcat:
- on machine1 (with sfc): nc -l 12345 > /dev/null
- on machine2: nc machine1 12345 < /dev/zero
- on machine1:
echo 1 > /sys/module/sfc/parameters/rx_alloc_method # use skbs
echo 2 > /sys/module/sfc/parameters/rx_alloc_method # use pages
- See that nc has quit suddenly.
[v2: Modified by Eric Dumazet to avoid advancing skb->data past the end
and to use a temporary variable.]
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 941666c2e3 "net: RCU conversion of dev_getbyhwaddr() and
arp_ioctl()" introduced a regression, reported by Jamie Heilman.
"arp -Ds 192.168.2.41 eth0 pub" triggered the ASSERT_RTNL() assert
in pneigh_lookup()
Removing RTNL requirement from arp_ioctl() was a mistake, just revert
that part.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
You always needed them when you were a module, but the builtin versions
of the macros used to be more lenient.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In commit 44b8288308 (net_sched: pfifo_head_drop problem), we fixed
a problem with pfifo_head drops that incorrectly decreased
sch->bstats.bytes and sch->bstats.packets
Several qdiscs (CHOKe, SFQ, pfifo_head, ...) are able to drop a
previously enqueued packet, and bstats cannot be changed, so
bstats/rates are not accurate (over estimated)
This patch changes the qdisc_bstats updates to be done at dequeue() time
instead of enqueue() time. bstats counters no longer account for dropped
frames, and rates are more correct, since enqueue() bursts dont have
effect on dequeue() rate.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
The option name of Delayed SACK Timer should be SCTP_DELAYED_SACK,
not SCTP_DELAYED_ACK.
Left SCTP_DELAYED_ACK be concomitant with SCTP_DELAYED_SACK,
for making compatibility with existing applications.
Reference:
8.1.19. Get or Set Delayed SACK Timer (SCTP_DELAYED_SACK)
（http://tools.ietf.org/html/draft-ietf-tsvwg-sctpsocket-25)
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0363466866 (net offloading: Convert checksums to use
centrally computed features.) mistakenly swapped can_checksum_protocol()
arguments.
This broke IPv6 on bnx2 for instance, on NIC without TCPv6 checksum
offloads.
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conn->sec_level value is supposed to represent the current level of
security that the connection has. However, by assigning to it before
requesting authentication it will have the wrong value during the
authentication procedure. To fix this a pending_sec_level variable is
added which is used to track the desired security level while making
sure that sec_level always represents the current level of security.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When there is an existing connection l2cap_check_security needs to be
called to ensure that the security level of the new socket is fulfilled.
Normally l2cap_do_start takes care of this, but that function doesn't
get called for SOCK_RAW type sockets. This patch adds the necessary
l2cap_check_security call to the appropriate branch in l2cap_do_connect.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The logic for determining the needed auth_type for an L2CAP socket is
rather complicated and has so far been duplicated in
l2cap_check_security as well as l2cap_do_connect. Additionally the
l2cap_check_security code was completely missing the handling of
SOCK_RAW type sockets. This patch creates a unified function for the
evaluation and makes l2cap_do_connect and l2cap_check_security use that
function.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If an existing connection has a MITM protection requirement (the first
bit of the auth_type) then that requirement should not be cleared by new
sockets that reuse the ACL but don't have that requirement.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This reverts commit 045309820a. That
commit is wrong for two reasons:
- The conn->sec_level shouldn't be updated without performing
authentication first (as it's supposed to represent the level of
security that the existing connection has)
- A higher auth_type value doesn't mean "more secure" like the commit
seems to assume. E.g. dedicated bonding with MITM protection is 0x03
whereas general bonding without MITM protection is 0x04. hci_conn_auth
already takes care of updating conn->auth_type so hci_connect doesn't
need to do it.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Fix a bug introduced in commit 9cf5b0ea3a7f1432c61029f7aaf4b8b338628884:
function rfcomm_recv_ua calls rfcomm_session_put without checking that
the session is not referenced by some DLC. If the session is freed, that
DLC would refer to deallocated memory, causing an oops later, as shown
in this bug report: https://bugzilla.kernel.org/show_bug.cgi?id=15994
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The blacklist should be freed before the hci device gets unregistered.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: "Gustavo F. Padovan" <padovan@profusion.mobi>
CC: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In netif_skb_features() we return only the features that are valid for vlans
if we have a vlan packet. However, we should not mask out NETIF_F_HW_VLAN_TX
since it enables transmission of vlan tags and is obviously valid.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network namespace is created (via CLONE_NEWNET), the loopback
interface is automatically added to the new namespace, triggering a
printk in ipv6_add_dev() if CONFIG_IPV6_PRIVACY is set.
This is problematic for applications which use CLONE_NEWNET as
part of a sandbox, like Chromium's suid sandbox or recent versions of
vsftpd. On a busy machine, it can lead to thousands of useless
"lo: Disabled Privacy Extensions" messages appearing in dmesg.
It's easy enough to check the status of privacy extensions via the
use_tempaddr sysctl, so just removing the printk seems like the most
sensible solution.
Signed-off-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code we check if (servl == NULL) twice. The first time
should print the message that cfmuxl_remove_uplayer() failed and set
"ret" correctly, but instead it just returns success. The second check
should be checking the value of "ret" instead of "servl".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the CAN socket code conform to the manpage of sendmsg.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux 2.6.21 defines different macros for __attribute__ which are also
used inside batman-adv. The next version of checkpatch.pl warns about
the usage of __attribute__((packed))).
Linux 2.6.33 defines an extra macro __always_unused which is used to
assist source code analyzers and can be used to removed the last
existing __attribute__ inside the source code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
* 'for-2.6.38' of git://linux-nfs.org/~bfields/linux: (62 commits)
nfsd4: fix callback restarting
nfsd: break lease on unlink, link, and rename
nfsd4: break lease on nfsd setattr
nfsd: don't support msnfs export option
nfsd4: initialize cb_per_client
nfsd4: allow restarting callbacks
nfsd4: simplify nfsd4_cb_prepare
nfsd4: give out delegations more quickly in 4.1 case
nfsd4: add helper function to run callbacks
nfsd4: make sure sequence flags are set after destroy_session
nfsd4: re-probe callback on connection loss
nfsd4: set sequence flag when backchannel is down
nfsd4: keep finer-grained callback status
rpc: allow xprt_class->setup to return a preexisting xprt
rpc: keep backchannel xprt as long as server connection
rpc: move sk_bc_xprt to svc_xprt
nfsd4: allow backchannel recovery
nfsd4: support BIND_CONN_TO_SESSION
nfsd4: modify session list under cl_lock
Documentation: fl_mylease no longer exists
...
Fix up conflicts in fs/nfsd/vfs.c with the vfs-scale work. The
vfs-scale work touched some msnfs cases, and this merge removes support
for that entirely, so the conflict was trivial to resolve.
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a problem in net/batman-adv/unicast.c::frag_send_skb().
dev_alloc_skb() allocates memory and may fail, thus returning NULL. If
this happens we'll pass a NULL pointer on to skb_split() which in turn
hands it to skb_split_inside_header() from where it gets passed to
skb_put() that lets skb_tail_pointer() play with it and that function
dereferences it. And thus the bat dies.
While I was at it I also moved the call to dev_alloc_skb() above the
assignment to 'unicast_packet' since there's no reason to do that
assignment if the memory allocation fails.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes. The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.
Thanks Johannes for helping me figure this one out.
Cc: stable@kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of the fixes for the
reorder timer, mac80211 will cause lockdep
warnings because lockdep confuses
local->skb_queue and local->rx_skb_queue
and treats their lock as the same.
However, their locks are different, and are
valid in different contexts (the former is
used in IRQ context, the latter in BH only)
and the only thing to be done is mark the
former as a different lock class so that
lockdep can tell the difference.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Sujith <m.sujith@gmail.com>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Sujith <m.sujith@gmail.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (41 commits)
fs: add documentation on fallocate hole punching
Gfs2: fail if we try to use hole punch
Btrfs: fail if we try to use hole punch
Ext4: fail if we try to use hole punch
Ocfs2: handle hole punching via fallocate properly
XFS: handle hole punching via fallocate properly
fs: add hole punching to fallocate
vfs: pass struct file to do_truncate on O_TRUNC opens (try #2)
fix signedness mess in rw_verify_area() on 64bit architectures
fs: fix kernel-doc for dcache::prepend_path
fs: fix kernel-doc for dcache::d_validate
sanitize ecryptfs ->mount()
switch afs
move internal-only parts of ncpfs headers to fs/ncpfs
switch ncpfs
switch 9p
pass default dentry_operations to mount_pseudo()
switch hostfs
switch affs
switch configfs
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix cleanup when trying to mount inexistent image
net/ceph: make ceph_msgr_wq non-reentrant
ceph: fsc->*_wq's aren't used in memory reclaim path
ceph: Always free allocated memory in osdmap_decode()
ceph: Makefile: Remove unnessary code
ceph: associate requests with opening sessions
ceph: drop redundant r_mds field
ceph: implement DIRLAYOUTHASH feature to get dir layout from MDS
ceph: add dir_layout to inode
This patch fixes a loop in ctnetlink_get_conntrack() that can be
triggered if you use the same socket to receive events and to
perform a GET operation. Under heavy load, netlink_unicast()
may return -EAGAIN, this error code is reserved in nfnetlink for
the module load-on-demand. Instead, we return -ENOBUFS which is
the appropriate error code that has to be propagated to
user-space.
Reported-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix new kernel-doc warning (copy-paste typo):
Warning(net/ethernet/eth.c:366): No description found for parameter 'rxqs'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller