Commit Graph

190 Commits

Author SHA1 Message Date
Russell King b65b4781fb ARM: Remove 'node' argument form arch_adjust_zones()
Since we no longer support discontigmem, node is always zero, so
remove this argument.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-16 10:57:36 +01:00
Sudhakar Rajashekhara ca2afb6dbe davinci: mmc: pass number of SG segments as platform data
On some platforms like DM355, the number of EDMA parameter slots available
for EDMA_SLOT_ANY usage are few.  In such cases, if MMC/SD uses 16 slots
for each instance of MMC controller, then the number of slots available
for other modules will be very few.

By passing the number of EDMA slots to be used in MMC driver from platform
data, EDMA slots available for other purposes can be controlled.

Most of the platforms will not use this platform data variable.  But on
DM355, as the number of EDMA resources available is limited, the number of
scatter- gather segments used inside the MMC driver can be 8 (passed as
platform data) instead of 16.  On DM355, when the number of scatter-gather
segments was reduced to 8, I saw a performance difference of about
0.25-0.4 Mbytes/sec during write.  Read performance variations were
negligible.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-27 09:12:39 -07:00
Thomas Koeller 7735227e76 DM365: Added more PINMUX configurations for AEMIF
More complete AEMIF support for boards.

Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 11:10:31 -07:00
Thomas Koeller 0efe2b7442 DM365: Make CLKOUTx available
Added PINMUX configurations for the CLKOUT0 .. CLKOUT2
functions, for boards that want to use these clocks.

Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 11:10:30 -07:00
Thomas Koeller 2168e76d6b DM365: Added PINMUX definitions for GPIO30..32
Board code may want to use them.

Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 11:10:30 -07:00
Cyril Chemparathy bcd6a1c695 Davinci: iotable based ioremap() interception
This patch allows for a more flexible ioremap() interception based on iotable
contents.

With this patch, the ioremap() interception code can properly translate
addresses only after davinci_soc_info has been initialized.  Consequently,
in soc-specific init functions, davinci_common_init() has to happen before any
ioremap() attempts. The da8xx init sequence has been suitably modified to meet
this restriction.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 10:05:31 -07:00
Cyril Chemparathy 779b0d53ca Davinci: pinmux - use ioremap()
This patch modifies the pinmux implementation so as to ioremap() the pinmux
register area on first use.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 10:05:29 -07:00
Cyril Chemparathy bd80894704 Davinci: aintc/cpintc - use ioremap()
This patch implements the following:

 - interrupt initialization uses ioremap() instead of passing a virtual address
   via davinci_soc_info.

 - machine definitions directly point to cp_intc_init() or davinci_irq_init()

 - davinci_intc_type and davinci_intc_base now get initialized in controller
   specific init functions instead of davinci_common_init()

 - minor fix in davinci_irq_init() to use intc_irq_num instead of
   DAVINCI_N_AINTC_IRQ

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 10:05:28 -07:00
Cyril Chemparathy e4c822c7e9 Davinci: psc - use ioremap()
This patch modifies the psc and clock control code to use ioremap()ed
registers.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 10:05:27 -07:00
Cyril Chemparathy 1bcd38ad2d Davinci: timer - use ioremap()
This patch eliminates IO_ADDRESS() usage for Davinci timer definitions.  The
timer code has correspondingly been modified to ioremap() MMRs instead.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 10:05:26 -07:00
Cyril Chemparathy 3347db8392 Davinci: jtag_id - use ioremap()
This patch replaces the jtag id base info in davinci_soc_info with a physical
address which is then ioremap()ed within common code.

This patch (in combination with a similar change for PSC) will allow us to
eliminate the SYSCFG nastiness in DA8xx code.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 10:05:24 -07:00
Cyril Chemparathy b8d4429395 Davinci: gpio - use ioremap()
This patch modifies the gpio_base definition in davinci_soc_info to be a
physical address, which is then ioremap()ed by the gpio initialization
function.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-13 10:05:22 -07:00
Cyril Chemparathy da0122ca8b Davinci: serial - remove unnecessary define
The uart pdata array is already terminated by a zero flag field.

This patch reuses this terminator and eliminates DAVINCI_MAX_NR_UARTS
definition.  This way, future platforms can have different number of uarts
initialized via davinci_serial_init().

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:10 -07:00
Cyril Chemparathy c78a5bc2e7 Davinci: watchdog reset separation across socs
The earlier watchdog reset mechanism had a couple of limitations.  First, it
embedded a reference to "davinci_wdt_device" inside common code.  This
forced all derived platforms (da8xx and tnetv107x) to define such a device.
This also would have caused problems in including multiple socs in a single
build due to symbol redefinition.

With this patch, davinci_watchdog_reset() now takes the platform device as an
argument.  The davinci_soc_info struct has been extended to include a reset
function and a watchdog platform_device.  arch_reset() then uses these
elements to reset the system in a SoC specific fashion.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:09 -07:00
Cyril Chemparathy 5b3a05ca91 Davinci: eliminate pinmux offset verbosity
Pinmux registers are sequential, and do not need to be enumerated out as they
currently are.  This reduces code volume and keeps things simple.

If some future SoC comes up with a discontiguous register map, PINMUX() can
then be expanded with local token pasting.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:09 -07:00
Cyril Chemparathy b27b6d03f2 Davinci: gpio - fine grained locking
This patch eliminates the global gpio_lock, and implements a per-controller
lock instead.  This also switches to irqsave/irqrestore locks in case gpios
are manipulated in isr.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:09 -07:00
Cyril Chemparathy 686b634a07 Davinci: gpio - controller type support
This patch allows for gpio controllers that deviate from those found on
traditional davinci socs.  davinci_soc_info has an added field to indicate the
soc-specific gpio controller type.  The gpio initialization code then bails
out if necessary.

More elements (tnetv107x) to be added later into enum davinci_gpio_type.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:08 -07:00
Cyril Chemparathy c12f415a91 Davinci: gpio - register layout invariant inlines
This patch renders the inlined gpio accessors in gpio.h independent of the
underlying controller's register layout.  This is done by including three new
fields in davinci_gpio_controller to hold the addresses of the set, clear, and
in data registers.

Other changes:

1. davinci_gpio_regs structure definition moved to gpio.c.  This structure is
no longer common across all davinci socs (davinci_gpio_controller is).

2. controller base address calculation code (gpio2controller()) moved to
gpio.c as this was no longer necessary for the inline implementation.

3. modified inline range checks to use davinci_soc_info.gpio_num instead of
DAVINCI_N_GPIO.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:08 -07:00
Cyril Chemparathy 99e9e52de6 Davinci: gpio - structs and functions renamed
Renamed gpio types to something more sensible:
	struct gpio_controller	--> struct davinci_gpio_regs
	struct davinci_gpio	--> struct davinci_gpio_controller
	gpio2controller()	--> gpio2regs()
	irq2controller()	--> irq2regs()

This change also moves davinci_gpio_controller definition to gpio.h.
Eventually, the gpio registers structure will be moved to gpio.c and no longer
a common cross-soc definition.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:08 -07:00
Sergei Shtylyov 7a9978a1e2 DaVinci: move IDE platform device to its proper place
The IDE platform device is registered in three different places (2 board files
for DM644x and in dm646x.c for DM646x) while both the IDE base address and the
IDE IRQ are the same for both SoCs -- therefore,  the proper place for the IDE
platform seems to be in devices.c. Merge the IDE platform data and registration
code and create davinci_init_ide() in place of dm646x_init_ide()...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:07 -07:00
Thomas Koeller 280faffb4e davinci: mach/common.h: add missing includes
linux/compiler.h is required for __iomem
linux/types.h is required u32

Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:07 -07:00
Thomas Koeller ce100669d2 davinci: DM365: Allow use of GPIO64_57
Extended the MUX configuration to allow use of GPIO
terminals 64..57.

Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:06 -07:00
Sergei Shtylyov 7034217467 DaVinci: move AEMIF #define's to the proper headers
Currently each DaVinci board file #define's its own version of the EMIFA base
addresses (all named DAVINCI_ASYNC_EMIF_*_BASE), which leads to duplication.
Move these #define's to the SoC specific headers, changing their prefixes from
'DAVINCI' to the 'DM355', 'DM644X', and 'DM646X' since all these base addresses
are SoC specific...

And while at it, rename DM646X_ASYNC_EMIF_DATA_CE0_BASE to
DM646X_ASYNC_EMIF_CS2_SPACE_BASE in order to match the DM646x datasheet.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:06 -07:00
Cyril Chemparathy ef03592a1a Davinci: tnetv107x cpu types
Added tnetv107x cpu type definitions and cpu identification macros.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:05 -07:00
Cyril Chemparathy 6cc20cd8ed Davinci: tnetv107x IRQ definitions
IRQ numbers as defined for tnetv107x cp_intc.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:05 -07:00
Cyril Chemparathy 7520f4eded Davinci: tnetv107x LPSC modules
Added definitions for LPSC modules in the tnetv107x SOC

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:05 -07:00
Cyril Chemparathy 0e23f71d60 Davinci: tnetv107x pin list
Added list of muxed pins on the tnetv107x SOC.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:04 -07:00
Cyril Chemparathy 3821d10a53 Davinci: promote da8xx_pinmux_setup()
Rename da8xx_pinmux_setup() to davinci_cfg_reg_list() and promote it for use in
other SOCs that may need the ability to configure multiple pins in one shot.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:04 -07:00
Cyril Chemparathy 52958be3ad Davinci: support LPSC SwRstDisable state
The current clock control code always gates the clock (PSC state Disable = 2)
on clk_disable().  Some on-chip peripherals (e.g. LCD controller on TNETV107X)
need to be put into SwRstDisable = 0 on clock disable, to maintain
hardware sanity.

This patch extends the davinci_psc_config() arguments to pass in the desired
module state instead of a boolean enable/disable.  Further, clk_disable() now
checks for the PSC_SWRSTDISABLE clk flag before selecting the target state.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:04 -07:00
Cyril Chemparathy 449ef7f6a9 Davinci: cpintc host map configuration
Host map configuration instructs the interrupt controller to route interrupt
channels to FIQ or IRQ lines.  Currently, DA8xx family of devices leave these
registers at their reset-default values.

TNETV107X however does not have sane reset defaults, and therefore this
architecture needs to reconfigure the host-map such that channels 0 and 1
go to FIQ, and the remaining channels raise IRQs.

This patch adds an optional host map argument to cp_intc_init() for this.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:04 -07:00
Kevin Hilman 28552c2eae davinci: misc cleanups from sparse
- Convert data/functions to static
- include headers for missing declarations
- pointer cleanups:  struct foo *__iomem f --> struct foo __iomem *f;

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-06 15:02:01 -07:00
Sergei Shtylyov 75392dd304 davinci: fix compile warning: <mach/da8xx.h>: #include <linux/platform_device.h>
This hushes the following warning:

arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: ‘struct platform_device’
declared inside parameter list
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-04-07 09:51:58 -07:00
Sekhar Nori 5eb2e891f0 davinci: da8xx/omap-l1: fix build error when CONFIG_DAVINCI_MUX is undefined
The da8xx/omap-l1 boards refuse to build when CONFIG_DAVINCI_MUX is undefined
because arch/arm/mach-davinci/mux.c:da8xx_pinmux_setup() is not defined.

This patch fixes this issue. This is build tested with davinci_all_defconfig
and da8xx_omapl_defconfig and boot tested on DA830 EVM.

Reported-by: Shanmuga Sundaram Mahendran <shanmuga@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-04-05 15:25:11 -07:00
Jiri Kosina 318ae2edc3 Merge branch 'for-next' into for-linus
Conflicts:
	Documentation/filesystems/proc.txt
	arch/arm/mach-u300/include/mach/debug-macro.S
	drivers/net/qlge/qlge_ethtool.c
	drivers/net/qlge/qlge_main.c
	drivers/net/typhoon.c
2010-03-08 16:55:37 +01:00
Linus Torvalds 13dda80e48 Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
  DaVinci DM365: Adding support for SPI EEPROM
  DaVinci DM365: Adding DM365 SPI support
  DaVinci DM355: Modifications to DM355 SPI support
  DaVinci: SPI: Adding header file for SPI support.
  davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
  davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
  DaVinci: DM365: Voice codec support for the DM365 SoC
  davinci: clock: let clk->set_rate function sleep
  Add SDA and SCL pin numbers to i2c platform data
  davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
  davinci: build list of unused EDMA events dynamically
  davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
  davinci: Keep count of channel controllers on a platform
  davinci: Correct return value of edma_alloc_channel api
  davinci: add CDCE949 support on DM6467 EVM
  davinci: add support for CDCE949 clock synthesizer
  davinci: da850/omap-l138 EVM: register for suspend support
  davinci: da850/omap-l138: add support for SoC suspend
  davinci: add power management support
  DaVinci: DM365: Changing default queue for DM365.
  ...
2010-03-01 13:05:40 -08:00
Sandeep Paulraj a3e13e89d6 DaVinci DM365: Adding DM365 SPI support
This patch adds SPI init for DM365.
It does the following
1) Initializes SPI0
2) Defines resources to be used by SPI0
3) Adds platform data for SPI0

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-03-01 10:20:24 -08:00
Sandeep Paulraj 8e2a0013c2 DaVinci: SPI: Adding header file for SPI support.
This patch adds "spi.h" header file that will be used by board and
architecture specific code.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-03-01 10:20:22 -08:00
Linus Torvalds ac0f6f927d Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits)
  ARM: Eliminate decompressor -Dstatic= PIC hack
  ARM: 5958/1: ARM: U300: fix inverted clk round rate
  ARM: 5956/1: misplaced parentheses
  ARM: 5955/1: ep93xx: move timer defines into core.c and document
  ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c
  ARM: 5953/1: ep93xx: fix broken build of clock.c
  ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig
  ARM: 5949/1: NUC900 add gpio virtual memory map
  ARM: 5948/1: Enable timer0 to time4 clock support for nuc910
  ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
  ARM: make_coherent(): fix problems with highpte, part 2
  MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself
  ARM: 5945/1: ep93xx: include correct irq.h in core.c
  ARM: 5933/1: amba-pl011: support hardware flow control
  ARM: 5930/1: Add PKMAP area description to memory.txt.
  ARM: 5929/1: Add checks to detect overlap of memory regions.
  ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
  ARM: 5927/1: Make delimiters of DMA area globally visibly.
  ARM: 5926/1: Add "Virtual kernel memory..." printout.
  ARM: 5920/1: OMAP4: Enable L2 Cache
  ...

Fix up trivial conflict in arch/arm/mach-mx25/clock.c
2010-03-01 09:15:15 -08:00
Murali Karicheri a30d6744cf V4L/DVB: DaVinci - Adding platform & board changes for vpfe capture on DM365
This patch adds following changes:-
	1) add sub device configuration data for TVP5146 used by vpfe capture
	2) registers platform devices for vpfe_capture, isif and vpss
	3) defines hardware resources for the devices listed under 2)
	4) defines clock aliase for isif driver
	5) adding setup_pinmux() for isif

Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2010-02-26 15:11:06 -03:00
Russell King 2741ecb4ce Merge branch 'misc2' into devel 2010-02-25 22:09:41 +00:00
Russell King 186f93ea1f Merge branch 'tmpreg' into devel
Conflicts:
	arch/arm/Kconfig
	arch/arm/mach-ux500/include/mach/debug-macro.S
2010-02-25 22:07:25 +00:00
Fenkart/Bostandzhyan c931b4f655 ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
Makes it consistent with VMALLOC_START

Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-02-15 21:40:33 +00:00
Tony Lindgren 4e6d488af3 ARM: 5910/1: ARM: Add tmp register for addruart and loadsp
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.

NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:

$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
	arch/arm/*/include/*/debug-macro.S

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-02-12 17:27:52 +00:00
Stefan Weil 947af29435 Fix spelling of 'platform' in comments and doc
Replace platfrom -> platform.

This is a frequent spelling bug.

Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-02-05 12:22:34 +01:00
Kevin Hilman 08aca087f2 davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
Remove unneeded 'struct davinci_clk' wrapper around 'struct clk_lookup'
and use clkdev_add_table() to add the list of clocks in one go.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-04 13:30:09 -08:00
Miguel Aguilar e89861e9b4 DaVinci: DM365: Voice codec support for the DM365 SoC
This patch adds the generic Voice Codec support for the DM365 based
platforms.

Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-04 13:30:09 -08:00
Philby John 00642f6616 Add SDA and SCL pin numbers to i2c platform data
Patch adds SDA and SCL pin numbers to the i2c platform data
structure for Davinci DM355 and DM6446. This at present is
used for i2c bus recovery.
TODO: Add SDA and SCL pin number information to include all
Davinci platforms such as dm355-leopard, dm365, dm646x, da8xx etc.

Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-04 13:30:06 -08:00
Sudhakar Rajashekhara f900d552f9 davinci: build list of unused EDMA events dynamically
Currently, the edma_noevent list is passed from platform data.
But on some architectures, there will be many EDMA channels
which will not be used at all. This patch scans all the
platform devices and then builds a list of events which are
not being used. The unused event list will be used to allocate
EDMA channels in case of EDMA_CHANNEL_ANY usage instead of the
edma_noevent being used earlier for this purpose.

This patch is based on David Brownells's suggestion at
http://article.gmane.org/gmane.linux.davinci/15176.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-04 13:30:02 -08:00
Nageswari Srinivasan 5b8972d1b6 davinci: add support for CDCE949 clock synthesizer
This patch adds support for TI's CDCE949 - a clock
synthesizer with 4 PLLs and 9 outputs.

It is used on DM6467 EVM. On the EVM, it generates
clocks required for VPIF, TSIF and Audio modules.

This patch adds it as part of the DaVinci clock framework.

Testing:
The various frequency outputs on Y1 have been tested using
a out-of-tree VPIF video driver supporting HD video.
The register values for Y5 frequency outputs have been
derived from TSIF driver sources in MontaVista LSP kernel,
but actual output has not been tested for lack of TSIF
driver which actually works on the latest kernel.

Signed-off-by: Nageswari Srinivasan <nageswari@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-04 13:29:58 -08:00
Sekhar Nori 044ca01521 davinci: da850/omap-l138: add support for SoC suspend
This patch adds support for registering for suspend-to-RAM
functionality on da850/omap-l138 SoCs.

da850 supports wakeup based on external event and RTC
alarm.

Currently only RTC alarm based wakeup is supported.
Support for wakeup based on external event will be
added as later improvements.

For scheduling an alarm event on RTC some useful code
is present in Documentation/rtc.txt

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-04 13:29:56 -08:00