Remove initialisers that set .aneg_done to genphy_aneg_done - this is
the default for clause 22 PHYs, so the initialiser is redundant.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.6. Major changes:
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
The FIELD_SIZEOF() macro was redundant, and is being removed from the
kernel. Since commit c593642c8b ("treewide: Use sizeof_field() macro")
this is one of the last users of the old macro, so replace it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Three of the WMI command handlers were not casting to the right data type.
Lets make the code consistent with the other handlers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
set_cqm_rssi_config() is used by the kernel to configure connection
quality monitor RSSI threshold.
wil6210 uses WMI_SET_LINK_MONITOR_CMDID to set the RSSI threshold to
FW which in turn reports RSSI threshold changes with
WMI_LINK_MONITOR_EVENTID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wil6210 AP has a separate ring for transmitting multicast packets,
multicast packets are transmitted without an ack from the receiver side.
Therefore, 802.11 spec defines some low MCS rates for multicat packets.
However, there is no guarantee that these packets were really received
and handled on the client side.
Some applications that rely on multicast packets, may prefer to
transmit these packets as a unicast to ensure reliability, and also
to ensure better performance with high MCS rates.
multicast to unicast is done by duplicating multicast packets to all
clients and changing the DA (multicast) to the MAC address of the
client.
see NL80211_CMD_SET_MULTICAST_TO_UNICAST for more info.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix incorrect definitions of MAC ID bits inside Rx status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ucode_debug memory region defined as 4K bytes. Fix this according to
Talyn device memory map.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
max_assoc_sta can receive values (from the user or from the FW)
that are higher than WIL6210_MAX_CID.
Verify that cid doesn't exceed the upper bound of WIL6210_MAX_CID.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some crash dump cases mem_lock is already taken, error
returns and crash dump copy fails.
In this case wait until mem_lock available instead of failing
the operation.
Also take the mem_lock for writing to prevent other threads from
altering the state of the device while collecting crash dump.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mem_lock is taken for the entire wil_reset().
Optimize this by taking mem_lock just before device is
being reset and release the lock after FW download.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dump all the Rx status message on different errors to allow more
visibility of the case.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. ixgbe_down already calls synchronize_rcu after setting __IXGBE_DOWN.
2. After switching the XDP program, call synchronize_rcu to let
ixgbe_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down.
4. Disabling UMEM sets __IXGBE_TX_DISABLED before closing hardware
resources and resetting xsk_umem. Check that bit in ixgbe_xsk_wakeup to
avoid using the XDP ring when it's already destroyed. synchronize_rcu is
called from ixgbe_txrx_ring_disable.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-5-maximmi@mellanox.com
Use synchronize_rcu to wait until the XSK wakeup function finishes
before destroying the resources it uses:
1. i40e_down already calls synchronize_rcu. On i40e_down either
__I40E_VSI_DOWN or __I40E_CONFIG_BUSY is set. Check the latter in
i40e_xsk_wakeup (the former is already checked there).
2. After switching the XDP program, call synchronize_rcu to let
i40e_xsk_wakeup exit before the XDP program is freed.
3. Changing the number of channels brings the interface down (see
i40e_prep_for_reset and i40e_pf_quiesce_all_vsi).
4. Disabling UMEM sets __I40E_CONFIG_BUSY, too.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-4-maximmi@mellanox.com
After disabling resources necessary for XSK (the XDP program, channels,
XSK queues), use synchronize_rcu to wait until the XSK wakeup function
finishes, before freeing the resources.
Suspend XSK wakeups during switching channels. If the XDP program is
being removed, synchronize_rcu before closing the old channels to allow
XSK wakeup to complete.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191217162023.16011-3-maximmi@mellanox.com
For ARCHs that don't support 64 bits division we need to use the
helpers.
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle TC_SETUP_QDISC_ETS, add a new ops structure for the ETS Qdisc.
Invoke the extended prio handlers implemented in the previous patch. For
stats ops, invoke directly the prio callbacks, which are not sensitive to
differences between PRIO and ETS.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to the similarity between PRIO and ETS it is possible to simply
reuse most of the code for offloading PRIO Qdisc. Extract the common
functionality into separate functions, making the current PRIO handlers
thin API adapters.
Extend the new functions to pass quanta for individual bands, which allows
configuring a subset of bands as WRR. Invoke mlxsw_sp_port_ets_set() as
appropriate to de/configure WRR-ness and weight of individual bands.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These enums want to be named MLXSW_REG_QEEC_HIERARCHY_, but due to a typo
lack the second H. That is confusing and complicates searching.
But actually the enumerators should be named _HR_, because that is how
their enum type is called. So rename them as appropriate.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the comment at mlxsw_sp_qdisc_prio_graft() to make the problem that
this function is trying to handle clearer.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be useful for debug. Add these counters on GMAC5+ cores just
like we did for XGMAC.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the HW specific support for Frame Preemption on XGMAC3+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the HW specific support for Frame Preemption on GMAC5+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for Frame Preemption using TAPRIO API. This works along
with EST feature and allows to select if preemptable traffic shall be
sent during specific queues opening time.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the EST code for XGMAC and QoS we can use it with the
TAPRIO scheduler. Integrate it into the main driver and use the API to
configure the EST feature.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for EST in XGMAC cores. This feature allows to offload
scheduling of queues opening time to the IP.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for EST in GMAC5+ cores. This feature allows to offload
scheduling of queues opening time to the IP.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have pending packets we re-arm the TX timer with a magic value.
This changes the re-arm of the timer from 10us to the user-defined
coalesce value. As we support different speeds, having a magic value of
10us can be either too short or to large depending on the speed so we
let user configure it. The default value of the timer is 1ms but it can
be reconfigured by ethtool.
Changes from v1:
- Reword commit message (Jakub)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using this mechanism we can get rid of the not so nice method of
scheduling TX NAPI when the RX was scheduled. No bandwidth reduction was
seen with this change.
Changes from v1:
- Remove useless comment (Jakub)
- Do not bind the TX clean to NAPI budget (Jakub)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA Capabilites have grown but the DebugFS that shows this info has not
been updated. Lets add the missing information.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the last received buffer contains the FCS field. Check for end of
packet before trying to strip the FCS field.
Fixes: 88ebe2cf7f ("net: stmmac: Rework stmmac_rx()")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.
Changes from v2:
- Do not try to align already aligned buffer size
Fixes: 67afd6d1cf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.
Check if available multicast addresses is enough before running the
tests.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ezusb_init, if upriv is NULL, the code crashes. However, the caller
in ezusb_probe can handle the error and print the failure message.
The patch replaces the BUG_ON call to error return.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NVIDIA Tegra SoCs do not like when OOB wake is enabled and WiFi interface
is in DOWN state during suspend. This results in a CPU hang on programming
OOB wake-up state of the GPIO controller during of system's suspend.
The solution is trivial: don't enable wake for the OOB interrupt when it
should be disabled.
This fixes hang on Tegra20 (Acer A500) and Tegra30 (Nexus 7) devices which
are using BCM4329 and BCM4330 WiFi chips respectively.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_usbdev_qinit() the allocated memory for
reqs is leaking if usb_alloc_urb() fails. Release reqs in the error
handling path.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With RSDB mode, FMAC and firmware are able to create 2 or more AP,
so we should not set mbss in vif structure if firmware does not
support MBSS feature.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With firmware RSDB feature
1. The maximum support interface is four.
2. The maximum difference channel is two.
3. The maximum interfaces of {station/p2p client/AP} are two.
4. The maximum interface of p2p device is one.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BCM4359 is a 2x2 802.11 abgn+ac Dual-Band HT80 combo chip and it
supports Real Simultaneous Dual Band feature.
Based on a similar patch by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4359 dongles do not support setting roaming parameters (error -52).
Do not fail the 80211 configuration in this case.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer 4359 chip revisions need a different rambase address.
This fixes firmware download on such devices which fails otherwise.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4359. Also
enable and configure F1 MesBusyCtrl. It fixes DMA error while having
UDP bi-directional traffic.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
[slightly adapted for rebase on mainline linux]
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two D11 cores in RSDB chips like 4359. We have to reset two
D11 cores simutaneously before firmware download, or the firmware may
not be initialized correctly and cause "fw initialized failed" error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92de_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92de_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92c_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92ce_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92ce_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92d_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92c_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92c_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
storage interface descriptors to avoid submitting an URB to an invalid
endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: a1030e92c1 ("[PATCH] zd1211rw: Convert installer CDROM device into WLAN device")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Cc: stable <stable@vger.kernel.org> # 4.4
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 9afac70a73 ("orinoco: add orinoco_usb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Cc: stable <stable@vger.kernel.org> # 3.4
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting, which may not be the
same as the first alternate setting, also when printing the number of
endpoints at probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's important as brcmfmac creates one main interface for each PHY and
doesn't allow deleting it. Not setting carrier could result in other
subsystems misbehaving (e.g. LEDs "netdev" trigger turning LED on).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 7afb94da3c ("mwifiex: update set_mac_address logic") fixed the
only user of this function, partly because the author seems to have
noticed that, as written, it's on the borderline between highly
misleading and buggy.
Anyway, no sense in keeping dead code around: let's drop it.
Fixes: 7afb94da3c ("mwifiex: update set_mac_address logic")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'forced' is duplicated in the message, axe one of them.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
error: dereferencing freed memory 'pkt'
It looks like there was supposed to be a continue after we free "pkt".
Fixes: 4754fceeb9 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver expects at least one bulk-in endpoint when in "wifi-alone"
operating mode and two bulk-in endpoints otherwise, and would otherwise
fail to to submit the corresponding bulk URB to the default pipe during
probe with a somewhat cryptic message:
rsi_91x: rsi_rx_urb_submit: Failed in urb submission
rsi_91x: rsi_probe: Failed in probe...Exiting
RSI-USB WLAN: probe of 2-2.4:1.0 failed with error -8
The current endpoint sanity check looks broken and would only bail out
early if there was no bulk-in endpoint but at least one bulk-out
endpoint.
Tighten this check to always require at least one bulk-in and one
bulk-out endpoint, and add the missing sanity check for a Bluetooth
bulk-in endpoint when in a BT operating mode. Also make sure to log an
informative error message when the expected endpoints are missing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB completion handlers are called in atomic context and must
specifically not allocate memory using GFP_KERNEL.
Fixes: a1854fae14 ("rsi: improve RX packet handling in USB interface")
Cc: stable <stable@vger.kernel.org> # 4.17
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to free the skb on failed receive-URB submission (e.g. on
disconnect or currently also due to a missing endpoint).
Fixes: a1854fae14 ("rsi: improve RX packet handling in USB interface")
Cc: stable <stable@vger.kernel.org> # 4.17
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver would fail to stop the command timer in most error paths,
something which specifically could lead to the timer being freed while
still active on I/O errors during probe.
Fix this by making sure that each function starting the timer also stops
it in all relevant error paths.
Reported-by: syzbot+1d1597a5aa3679c65b9f@syzkaller.appspotmail.com
Fixes: b78e91bcfb ("rsi: Add new firmware loading method")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to stop both URBs before returning after failed probe as well
as on disconnect to avoid use-after-free in the completion handler.
Reported-by: syzbot+b563b7f8dbe8223a51e8@syzkaller.appspotmail.com
Fixes: a4302bff28 ("rsi: add bluetooth rx endpoint")
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can not set IV when we are under reset. Previously we read previous
IV value from registers and zeroed IV registers when key was deleted,
but this could possibly not work if DEL_KEY command was not performed.
Now when we have ->reconfig_complete ops and we fully mark mac80211
reset state via DEVICE_STATE_RESET flag, we can just skip setting IV
when keys are set during reset.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 has .reconfig_complete that can be used as indicator of
HW restart end. This will allow to configure keys/IV differently
for HW restart and normal configuration.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As 'channel' is declared as u16, the following expression is always false.
channel < 0
So we can remove unnecessary 'always false' statement.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All usage of the local macros have been removed, thus the remaining
definitions are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changed macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The special macros are used in several places in the base driver.
These are replaced by standard bit manipulation macros or code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changes macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changes macros for the RX and TX descriptors.
the local macros are used in other places. These are replaced with
standard bit manipulation macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Besides the previously changes macros in trx.h, there are some of these
local macros in the driver. These are replaced with standard bit
manipulations. Unused macros are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
and other warnings are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_p2p_create_p2pdev() the allocated memory
for p2p_vif is leaked when the mac address is the same as primary
interface. To fix this, go to error path to release p2p_vif via
brcmf_free_vif().
Fixes: cb746e4783 ("brcmfmac: check p2pdev mac address uniqueness")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the signal stregth decays smoothly and physical connnection
is already gone and no deauth has arrived, the qcom soc is not
able to indicate neither WCN36XX_HAL_MISSED_BEACON_IND nor
WCN36XX_HAL_MISSED_BEACON_IND. It was noticed that such situation gets
even more reproducible, when the driver fails to enter bmps mode - which is
highly likely to occur. Thus, in order to provide proper disconnection
of the connected STA, let mac80211 handle it, instead of wcn3xx driver.
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
storage interface descriptors to avoid submitting an URB to an invalid
endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 36bcce4306 ("ath9k_htc: Handle storage devices")
Cc: stable <stable@vger.kernel.org> # 2.6.39
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The list iterator is always non-NULL so it doesn't need to be checked.
I also removed the unnecessary initializer because the list iterator is
always initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath11k_ce_alloc_ring() function returns error pointers on error, not
NULL. The rest of the driver assumes that "pipe->src_ring" is either
valid or NULL so this patch introduces a temporary varaible to avoid
leaving it as an error pointer.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The callers unlock this lock so this error path has a double unlock.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error handling when the call to ath11k_hal_srng_get_entrysize fails
leaks skb, fix this by returning via the err_free return path that will
ensure the skb is free'd.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable radioup is not uninitalized so it may contain a garbage
value and hence the detection of a radio that is not up is buggy.
Fix this by initializing it to zero.
Addresses-Coverity: ("Uninitalized scalar variable")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently a return path is leaking the previously allocate reg_info. Fix
this by exiting via the return path mem_free. Since the return value ret
is defaulted to 0, there is no need to re-assign ret to the 0 before
the goto.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns:
drivers/net/wireless/ath/ath11k/wmi.c:1827:23: warning: implicit
conversion from enumeration type 'enum wmi_scan_priority' to different
enumeration type 'enum scan_priority' [-Wenum-conversion]
arg->scan_priority = WMI_SCAN_PRIORITY_LOW;
~ ^~~~~~~~~~~~~~~~~~~~~
1 warning generated.
wmi_scan_priority and scan_priority have the same values but the wmi one
has WMI prefixed to the names. Since that enum is already being used,
get rid of scan_priority and switch its one use to wmi_scan_priority to
fix this warning.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/808
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several spelling mistakes in warning and debug messages,
fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch sets the correct BA buffer size when we are in HE mode.
Without this change we are not able to receive 256 bitmapped BA frames.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code currently uses the wrong pdev id when enabling TWT. Fix this by
using the correct ones.
Fixes: e65a616f4e74 ("ath11k: add TWT support")
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the function into dp_tx.c allows gcc to optimize the code better
and also avoid chace invalidates and context switches.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the current code does 4 memcpys for each completion frame.
1) duplicate the desc
2 + 3) inside kfifo insertion
4) kfifo remove
The code simply drops the kfifo and uses a trivial ring buffer. This
requires a single memcpy for insertion. There is no removal needed as
we can simply use the inserted data for processing. As the code runs
inside the NAPI context it is atomic and there is no need for most of
the locking.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the fields are only used by debugfs. Move the parsing of these
from the data hot path to the debugfs code.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes the code consistent with the recent sc to ab rename.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no point in zero'ing out the structure if we set all values in the
following line.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After applying this setting the TX performance issue of STA interfaces is
gone and we can see TX performance go up to ~900mbit on HE80.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a WMI call helper to set the powersave mode of a STA interface.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing the 'hotplug-status' node in netback_remove() is wrong; the script
may not have completed. Only remove the node once the watch has fired and
has been unregistered.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
...as the comment above the function states.
The switch to Initialising at the start of the function is somewhat bogus
as the toolstack will have set that initial state anyway. To behave
correctly, a backend should switch to InitWait once it has set up all
xenstore values that may be required by a initialising frontend. This
patch calls backend_switch_state() to make the transition at the
appropriate point.
NOTE: backend_switch_state() ignores errors from xenbus_switch_state()
and so this patch removes an error path from netback_probe(). This
means a failure to change state at this stage (in the absence of
other failures) will leave the device instantiated. This is highly
unlikley to happen as a failure to change state would indicate a
failure to write to xenstore, and that will trigger other error
paths. Also, a 'stuck' device can still be cleaned up using 'unbind'
in any case.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
...of xenbus.c
This is a cosmetic function re-ordering to reduce churn in a subsequent
patch. Some style fix-up was done to make checkpatch.pl happier.
No functional change.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As flower rules are added, they are given a stats ID based on the number
of rules that can be supported in firmware. Only after the initial
allocation of all available IDs does the driver begin to reuse those that
have been released.
The initial allocation of IDs was modified to account for multiple memory
units on the offloaded device. However, this introduced a bug whereby the
counter that controls the IDs could be decremented before the ID was
assigned (where it is further decremented). This means that the stats ID
could be assigned as -1/0xfffffff which is out of range.
Fix this by only decrementing the main counter after the current ID has
been assigned.
Fixes: 467322e262 ("nfp: flower: support multiple memory units for filter offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_probe':
drivers/net/ethernet/atheros/ag71xx.c:1776:30: warning: passing argument 2 of
'of_get_phy_mode' makes pointer from integer without a cast [-Wint-conversion]
In file included from drivers/net/ethernet/atheros/ag71xx.c:33:
./include/linux/of_net.h:15:69: note: expected 'phy_interface_t *'
{aka 'enum <anonymous> *'} but argument is of type 'int'
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit c219399988 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in connection failures for
ULDs.
So, fix all related code to properly recalculate the TID start index
based on whether high priority filters are enabled or not.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c219399988 ("cxgb4: add support for high priority filters")
has missed considering high priority region calculation in some code
paths. This patch fixes them.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ql_alloc_large_buffers() has the usual RX buffer allocation
loop where it allocates skbs and maps them for DMA. It also
treats failure as a fatal error.
There are (at least) three bugs in the error paths:
1. ql_free_large_buffers() assumes that the lrg_buf[] entry for the
first buffer that couldn't be allocated will have .skb == NULL.
But the qla_buf[] array is not zero-initialised.
2. ql_free_large_buffers() DMA-unmaps all skbs in lrg_buf[]. This is
incorrect for the last allocated skb, if DMA mapping failed.
3. Commit 1acb8f2a7a ("net: qlogic: Fix memory leak in
ql_alloc_large_buffers") added a direct call to dev_kfree_skb_any()
after the skb is recorded in lrg_buf[], so ql_free_large_buffers()
will double-free it.
The bugs are somewhat inter-twined, so fix them all at once:
* Clear each entry in qla_buf[] before attempting to allocate
an skb for it. This goes half-way to fixing bug 1.
* Set the .skb field only after the skb is DMA-mapped. This
fixes the rest.
Fixes: 1357bfcf71 ("qla3xxx: Dynamically size the rx buffer queue ...")
Fixes: 0f8ab89e82 ("qla3xxx: Check return code from pci_map_single() ...")
Fixes: 1acb8f2a7a ("net: qlogic: Fix memory leak in ql_alloc_large_buffers")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd+P4eAAoJEG4XJFUm622bnOQH/RHSFFQNjxfPboZoozKb0/mT
6YtrG+0K1z8E21Os2bd+s4aRJgq1oGKDocMie5y53M38qQ5N3FchzcGopNRCRy/a
gF1PzEqceOysbEtPOx4yI+c0Gfi7rS0SjEyf2XKGowXsoIZh4j+1xlWbF/JtHt6n
J901W1GW0ZUCHaP8KuZcbsS2nfdV8tFW2NQW3Xuhy+nOdBhNRL/lKSvlhZLCCAfY
f1eJrB0rAzQpCqw8Wuz2JzWsxBiTt+6Ucuzv4EkFVrt7Xnj00feghTKJkVDqa+fL
B9hTiiYh8sLGJkYHsZLDZIzAdOW8jmun1I+XFsjdl7ucLRYz6U8NL9jc6oIGK00=
=KJmM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
First set of fixes for v5.5. Fixing security issues, some regressions
and few major bugs.
mwifiex
* security fix for handling country Information Elements (CVE-2019-14895)
* security fix for handling TDLS Information Elements
ath9k
* fix endian issue with ath9k_pci_owl_loader
mt76
* fix default mac address handling
iwlwifi
* fix merge damage which lead to firmware crashing during boot on some devices
* fix device initialisation regression on some devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reusing the ptp_qoriq driver, the ptp_qoriq_free() function was
used on the remove path to free any allocated resources.
The ptp_qoriq IRQ is among these resources that are freed in
ptp_qoriq_free() even though it is also a managed one (allocated using
devm_request_threaded_irq).
Drop the resource managed version of requesting the IRQ in order to not
trigger a double free of the interrupt as below:
[ 226.731005] Trying to free already-free IRQ 126
[ 226.735533] WARNING: CPU: 6 PID: 749 at kernel/irq/manage.c:1707
__free_irq+0x9c/0x2b8
[ 226.743435] Modules linked in:
[ 226.746480] CPU: 6 PID: 749 Comm: bash Tainted: G W
5.4.0-03629-gfd7102c32b2c-dirty #912
[ 226.755857] Hardware name: NXP Layerscape LX2160ARDB (DT)
[ 226.761244] pstate: 40000085 (nZcv daIf -PAN -UAO)
[ 226.766022] pc : __free_irq+0x9c/0x2b8
[ 226.769758] lr : __free_irq+0x9c/0x2b8
[ 226.773493] sp : ffff8000125039f0
(...)
[ 226.856275] Call trace:
[ 226.858710] __free_irq+0x9c/0x2b8
[ 226.862098] free_irq+0x30/0x70
[ 226.865229] devm_irq_release+0x14/0x20
[ 226.869054] release_nodes+0x1b0/0x220
[ 226.872790] devres_release_all+0x34/0x50
[ 226.876790] device_release_driver_internal+0x100/0x1c0
Fixes: d346c9e86d ("dpaa2-ptp: reuse ptp_qoriq driver")
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no clocks, resets or gpios referenced by Tegra ACPI
device so don't access clocks, resets or gpios interface with
ACPI device.
Clocks, resets and GPIOs for ACPI devices will be handled via
ACPI interface.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic device api so that driver can work both with DT
or ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT2712 SoC can provide the rmii reference clock, and the clock
will output from TXC pin only, which means ref_clk pin of external
PHY should connect to TXC pin in this case.
Add corresponding clock and timing settings.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up the mvpp2 validate implementation to adopt the same behaviour as
mvneta:
- only allow the link modes that the specified PHY interface mode
supports with the exception of 1000base-X and 2500base-X.
- use the basex helper to deal with SFP modules that can be switched
between 1000base-X vs 2500base-X.
This gives consistent behaviour between mvneta and mvpp2.
This commit depends on "net: phylink: extend clause 45 PHY validation
workaround" so is not marked for backporting to stable kernels.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e45d1f5288 ("net: phylink: support Clause 45 PHYs on SFP+
modules") added a workaround to support clause 45 PHYs which
dynamically switch their interface mode on SFP+ modules. This was
implemented by validating the PHYs supported/advertising using
PHY_INTERFACE_MODE_NA, rather than the specific interface mode that
we attached the PHY with.
However, we already have a situation where phylink is used to connect
a Marvell 88X3310 PHY which also behaves in exactly the same way, but
which seemingly doesn't need this. The reason seems to be that the
mvpp2 driver sets a whole bunch of link modes for
PHY_INTERFACE_MODE_10GKR down to 10Mb/s, despite 10GBASE-R not actually
supporting anything but 10Gb/s speeds.
When testing with drivers that (correctly) take the mvneta approach,
where the validate() method only returns what can be supported /
advertised for the specified link mode, we find that Clause 45 PHYs do
not behave as we expect: their advertisement is restricted to what
the current link will support, rather than what the PHY supports
through its dynamic switching.
Extend this workaround to all such cases; if we have a Clause 45 PHY
attaching via any means, except in USXGMII, XAUI and RXAUI which are
all unable to support this dynamic switching or have other solutions
to it, then we need to validate using PHY_INTERFACE_MODE_NA.
This should allow mvpp2 to switch to a more conformant validate()
implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing ethtool with the Methode DM7052 module, it was noticed
that attempting to set the advertising mask results in the mask being
truncated to the support offered by the currently chosen PHY interface
mode.
When a PHY dynamically changes the PHY interface mode, limiting the
advertising mask in this way is not correct - if the PHY happened to
negotiate 10GBASE-T, and selected 10GBASE-R as the host interface, we
don't want to restrict the advertisement to just 10GBASE-* modes.
Rework setting the advertisement to take account of this; do not pass
the requested advertisement through phylink_validate(), but rely on
the advertisement restriction (supported mask) set when the PHY was
initially setup.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some typo:
s/to to/to/
s/even/event/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The capabilities for the HE mesh are generated from the capabilities
reported by the fw. But the firmware only reports the overall capabilities
and not the one which are specific for mesh. Some of them (TWT, MU UL/DL,
TB PPDU, ...) require an infrastructure setup with a main STA (AP)
controlling the operations. This is not the case for mesh and thus these
capabilities are removed from the list of capabilities.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* disable AQL on most drivers, addressing the iwlwifi issues
* fix double-free on network namespace changes
* fix TID field in frames injected through monitor interfaces
* fix ieee80211_calc_rx_airtime()
* fix NULL pointer dereference in rfkill (and remove BUG_ON)
-----BEGIN PGP SIGNATURE-----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=tvTq
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2019-10-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* disable AQL on most drivers, addressing the iwlwifi issues
* fix double-free on network namespace changes
* fix TID field in frames injected through monitor interfaces
* fix ieee80211_calc_rx_airtime()
* fix NULL pointer dereference in rfkill (and remove BUG_ON)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting MSCC_OCELOT_SWITCH is not possible when NET_VENDOR_MICROSEMI
is disabled:
WARNING: unmet direct dependencies detected for MSCC_OCELOT_SWITCH
Depends on [n]: NETDEVICES [=y] && ETHERNET [=n] && NET_VENDOR_MICROSEMI [=n] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y]
Selected by [m]:
- NET_DSA_MSCC_FELIX [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && NET_DSA [=y] && PCI [=y]
Add a Kconfig dependency on NET_VENDOR_MICROSEMI, which also implies
CONFIG_NETDEVICES.
Depending on a vendor config violates menuconfig locality for the DSA
driver, but is the smallest compromise since all other solutions are
much more complicated (see [0]).
https://www.spinics.net/lists/netdev/msg618808.html
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove <linux/version.h> from the includes for main.c, which is unused.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
[Jason: reworded commit message]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two spelling errors in source code comments.
Signed-off-by: Josh Soref <jsoref@gmail.com>
[Jason: rewrote commit message]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the crypto selection submenu depenencies. Otherwise, we'd
wind up issuing warnings in which certain dependencies we also select
couldn't be satisfied. This condition was triggered by the addition of
the test suite autobuilder in the previous commit.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In caif_xmit, there is a crash if the ptr dev is NULL. However, by
returning the error to the callers, the error can be handled. The
patch fixes this issue.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of gmac_setup_txqs() the allocated desc_ring is
leaked if TX queue base is not aligned. Release it via
dma_free_coherent.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike mlxsw, the other listeners to the FIB notification chain do not
require any special modifications as they never considered multiple
identical routes.
This patch removes the old route notifications and converts all the
listeners to use the new replace / delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new notifications mlxsw does not need to handle identical
routes itself, as this is taken care of by the core IPv4 code.
Instead, mlxsw only needs to take care of inserting and removing routes
from the device.
Convert mlxsw to use the new IPv4 route notifications and simplify the
code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
service_task will be scheduled per second to do some periodic
jobs. When reset fails, it means this device is not available
now, so the periodic jobs do not need to be handled.
This patch adds flag HCLGE_STATE_RST_FAIL/HCLGEVF_STATE_RST_FAIL
to indicate that reset fails, and checks this flag before
schedule periodic task.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hns3 driver may be used in memory reclaim path when it
is the low level transport of a network file system, so it
needs to guarantee forward progress even under memory pressure.
This patch allocates a private WQ with WQ_MEM_RECLAIM set for
both hclge_main and hclgevf_main modules.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are four work (mbx_service_task, service_task,
rst_service_task and keep_alive_task)in the hclgevf module,
mbx_service_task is for handling mailbox issue, service_task is
for periodic management issue and rst_service_task is for reset
related issue, keep_alive_task is used to keepalive between PF
and VF, which can be done in a single work.
This patch removes the mbx_service_task, rst_service_task and
keep_alive_task, and moves the related handling to the
service_task work in order to remove concurrency between the four
work and to improve efficiency.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three work (mbx_service_task, service_task,
rst_service_task) in the HNS3 driver, mbx_service_task is for
handling mailbox work, service_task is for periodic management
issue and rst_service_task is for reset related issue, which can
be handled in a single work.
This patch removes the mbx_service_task and rst_service_task
work, and moves the related handling to the service_task work
in order to remove concurrency between the three work and to
improve efficiency.
BTW, since stats_timer in struct hclge_hw_stats is not needed
anymore, so removes the definition of struct hclge_hw_stats,
and moves mac_stats into struct hclge_dev.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a timer is defined to schedule hclgevf_service per
second. To simplify the code, this patch uses the delayed work
instead of timer to schedule hclgevf_serive.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several issues with 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback") that resulted in breaking connectivity for standalone ports:
- both user and CPU ports must allow unicast and multicast forwarding by
default otherwise this just flat out breaks connectivity for
standalone DSA ports
- IP multicast is treated similarly as multicast, but has separate
control registers
- the UC, MC and IPMC lookup failure register offsets were wrong, and
instead used bit values that are meaningful for the
B53_IP_MULTICAST_CTRL register
Fixes: 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add external trigger event support
for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function xenvif_disconnect_queue(), the value of queue->rx_irq is
zeroed *before* queue->task is stopped. Unfortunately that task may call
notify_remote_via_irq(queue->rx_irq) and calling that function with a
zero value results in a NULL pointer dereference in evtchn_from_irq().
This patch simply re-orders things, stopping all tasks before zero-ing the
irq values, thereby avoiding the possibility of the race.
Fixes: 2ac061ce97 ("xen/netback: cleanup init and deinit code")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Display the return code as decimal integer.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
A mismerge between the following two commits:
c678726305 ("net: phylink: ensure consistent phy interface mode")
27755ff88c ("net: phylink: Add phylink_mac_link_{up, down} wrapper functions")
resulted in the wrong interface being passed to the mac_link_up()
function. Fix this up.
Fixes: b4b12b0d2f ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
of_phy_attach() hides the return value of phy_attach_direct(), forcing
us to return a "generic" ENODEV error code that is indistinguishable
from the lack-of-phy-property case.
Switch to using of_phy_find_device() to find the PHY device, and then
propagating any phy_attach_direct() error back to the caller.
Link: https://lore.kernel.org/lkml/20191210113829.GT25745@shell.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
GTP default hashtable size is 1024 and userspace could set specific
hashtable size with IFLA_GTP_PDP_HASHSIZE. If hashtable size is set to 0
from userspace, hashtable will not work and panic will occur.
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
ipv4_pdp_find() is called in TX packet path of GTP.
ipv4_pdp_find() internally uses gtp->tid_hash to lookup pdp context.
In the current code, gtp->tid_hash and gtp->addr_hash are freed by
->dellink(), which is gtp_dellink().
But gtp_dellink() would be called while packets are processing.
So, gtp_dellink() should not free gtp->tid_hash and gtp->addr_hash.
Instead, dev->priv_destructor() would be used because this callback
is called after all packet processing safely.
Test commands:
ip link add veth1 type veth peer name veth2
ip a a 172.0.0.1/24 dev veth1
ip link set veth1 up
ip a a 172.99.0.1/32 dev lo
gtp-link add gtp1 &
gtp-tunnel add gtp1 v1 200 100 172.99.0.2 172.0.0.2
ip r a 172.99.0.2/32 dev gtp1
ip link set gtp1 mtu 1500
ip netns add ns2
ip link set veth2 netns ns2
ip netns exec ns2 ip a a 172.0.0.2/24 dev veth2
ip netns exec ns2 ip link set veth2 up
ip netns exec ns2 ip a a 172.99.0.2/32 dev lo
ip netns exec ns2 ip link set lo up
ip netns exec ns2 gtp-link add gtp2 &
ip netns exec ns2 gtp-tunnel add gtp2 v1 100 200 172.99.0.1 172.0.0.1
ip netns exec ns2 ip r a 172.99.0.1/32 dev gtp2
ip netns exec ns2 ip link set gtp2 mtu 1500
hping3 172.99.0.2 -2 --flood &
ip link del gtp1
Splat looks like:
[ 72.568081][ T1195] BUG: KASAN: use-after-free in ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.568916][ T1195] Read of size 8 at addr ffff8880b9a35d28 by task hping3/1195
[ 72.569631][ T1195]
[ 72.569861][ T1195] CPU: 2 PID: 1195 Comm: hping3 Not tainted 5.5.0-rc1 #199
[ 72.570547][ T1195] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 72.571438][ T1195] Call Trace:
[ 72.571764][ T1195] dump_stack+0x96/0xdb
[ 72.572171][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.572761][ T1195] print_address_description.constprop.5+0x1be/0x360
[ 72.573400][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.573971][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.574544][ T1195] __kasan_report+0x12a/0x16f
[ 72.575014][ T1195] ? ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.575593][ T1195] kasan_report+0xe/0x20
[ 72.576004][ T1195] ipv4_pdp_find.isra.12+0x130/0x170 [gtp]
[ 72.576577][ T1195] gtp_build_skb_ip4+0x199/0x1420 [gtp]
[ ... ]
[ 72.647671][ T1195] BUG: unable to handle page fault for address: ffff8880b9a35d28
[ 72.648512][ T1195] #PF: supervisor read access in kernel mode
[ 72.649158][ T1195] #PF: error_code(0x0000) - not-present page
[ 72.649849][ T1195] PGD a6c01067 P4D a6c01067 PUD 11fb07067 PMD 11f939067 PTE 800fffff465ca060
[ 72.652958][ T1195] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 72.653834][ T1195] CPU: 2 PID: 1195 Comm: hping3 Tainted: G B 5.5.0-rc1 #199
[ 72.668062][ T1195] RIP: 0010:ipv4_pdp_find.isra.12+0x86/0x170 [gtp]
[ ... ]
[ 72.679168][ T1195] Call Trace:
[ 72.679603][ T1195] gtp_build_skb_ip4+0x199/0x1420 [gtp]
[ 72.681915][ T1195] ? ipv4_pdp_find.isra.12+0x170/0x170 [gtp]
[ 72.682513][ T1195] ? lock_acquire+0x164/0x3b0
[ 72.682966][ T1195] ? gtp_dev_xmit+0x35e/0x890 [gtp]
[ 72.683481][ T1195] gtp_dev_xmit+0x3c2/0x890 [gtp]
[ ... ]
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
gtp_genl_dump_pdp() is ->dumpit() callback of GTP module and it is used
to dump pdp contexts. it would be re-executed because of dump packet size.
If dump packet size is too big, it saves current dump pointer
(gtp interface pointer, bucket, TID value) then it restarts dump from
last pointer.
Current GTP code allows adding zero TID pdp context but dump code
ignores zero TID value. So, last dump pointer will not be found.
In addition, this patch adds missing rcu_read_lock() in
gtp_genl_dump_pdp().
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
GTP RX packet path lookups pdp context with TID. If duplicate TID pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, TID value should be unique.
GTP TX packet path lookups pdp context with ms_addr. If duplicate ms_addr pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, ms_addr value should be unique.
Fixes: 459aa660eb ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After the recent fix in commit 1899bb3251 ("bonding: fix state
transition issue in link monitoring"), the active-backup mode with
miimon initially come-up fine but after a link-failure, both members
transition into backup state.
Following steps to reproduce the scenario (eth1 and eth2 are the
slaves of the bond):
ip link set eth1 up
ip link set eth2 down
sleep 1
ip link set eth2 up
ip link set eth1 down
cat /sys/class/net/eth1/bonding_slave/state
cat /sys/class/net/eth2/bonding_slave/state
Fixes: 1899bb3251 ("bonding: fix state transition issue in link monitoring")
CC: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The bond slave actor/partner operating state is exported as
bitfield to userspace, which lacks a way to interpret it, e.g.,
iproute2 only prints the state as a number:
ad_actor_oper_port_state 15
For userspace to interpret the bitfield, the bitfield definitions
should be part of the uapi. The bitfield itself is defined in the
802.3ad standard.
This commit moves the 802.3ad bitfield definitions to uapi.
Related iproute2 patches, soon to be posted upstream, use the new uapi
headers to pretty-print bond slave state, e.g., with ip -d link show
ad_actor_oper_port_state_str <active,short_timeout,aggregating,in_sync>
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Driver doesn't calculate total number of PFs configured on a
given engine correctly which messed up resources in the PFs
loaded on that engine, leading driver to exceed configuration
of resources (like vlan filters etc.) beyond the limit per
engine, which ended up with asserts from the firmware.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Parity error from the hardware will cause PF to lose the state
of their VFs due to PF's internal reload and hardware reset following
the parity error. Restrict any configuration request from the VFs after
the parity as it could cause unexpected hardware behavior, only way
for VFs to recover would be to trigger FLR on VFs and reload them.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Without the common part of the driver, the new file fails to link:
drivers/net/ethernet/ti/cpsw_new.o: In function `cpsw_probe':
cpsw_new.c:(.text+0x312c): undefined reference to `ti_cm_get_macid'
Use the same Makefile hack as before, and build cpsw-common.o for
any driver that needs it.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The new driver misses a dependency:
drivers/net/ethernet/ti/cpsw_new.o: In function `cpsw_rx_handler':
cpsw_new.c:(.text+0x259c): undefined reference to `__page_pool_put_page'
cpsw_new.c:(.text+0x25d0): undefined reference to `page_pool_alloc_pages'
drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_fill_rx_channels':
cpsw_priv.c:(.text+0x22d8): undefined reference to `page_pool_alloc_pages'
cpsw_priv.c:(.text+0x2420): undefined reference to `__page_pool_put_page'
drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_create_xdp_rxqs':
cpsw_priv.c:(.text+0x2624): undefined reference to `page_pool_create'
drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_run_xdp':
cpsw_priv.c:(.text+0x2dc8): undefined reference to `__page_pool_put_page'
Other drivers use 'select' for PAGE_POOL, so do the same here.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Host can provide send indirection table messages anytime after RSS is
enabled by calling rndis_filter_set_rss_param(). So the host provided
table values may be overwritten by the initialization in
rndis_set_subchannel().
To prevent this problem, move the tx_table initialization before calling
rndis_filter_set_rss_param().
Fixes: a6fb6aa3cf ("hv_netvsc: Set tx_table to equal weight after subchannels open")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
phylink requires the MAC to report when its link status changes when
operating in inband modes. Failure to report link status changes
means that phylink has no idea when the link events happen, which
results in either the network interface's carrier remaining up or
remaining permanently down.
For example, with a fiber module, if the interface is brought up and
link is initially established, taking the link down at the far end
will cut the optical power. The SFP module's LOS asserts, we
deactivate the link, and the network interface reports no carrier.
When the far end is brought back up, the SFP module's LOS deasserts,
but the MAC may be slower to establish link. If this happens (which
in my tests is a certainty) then phylink never hears that the MAC
has established link with the far end, and the network interface is
stuck reporting no carrier. This means the interface is
non-functional.
Avoiding the link interrupt when we have phylink is basically not
an option, so remove the !port->phylink from the test.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This reverts commit 78beef629f ("nfp: abm: fix memory leak in
nfp_abm_u32_knode_replace").
The quoted commit does not fix anything and resulted in a bogus
CVE-2019-19076.
If match is NULL then it is known there is no matching entry in
list, hence, calling nfp_abm_u32_knode_delete() is pointless.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
This conditional is missing a bang, with the intent
being to break when the retry count reaches zero.
Fixes: 476d96ca9c ("ibmvnic: Bound waits for device queries")
Suggested-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock. It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.
Fix by applying the corrected clamp value.
Fixes: 74706afa71 ("bnxt_en: Update interrupt coalescing logic.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Instead of just having an airtime flag in debugfs, turn AQL into a proper
NL80211_EXT_FEATURE, so drivers can turn it on when they are ready, and so
we also expose the presence of the feature to userspace.
This also has the effect of flipping the default, so drivers have to opt in
to using AQL instead of getting it by default with TXQs. To keep
functionality the same as pre-patch, we set this feature for ath10k (which
is where it is needed the most).
While we're at it, split out the debugfs interface so AQL gets its own
per-station debugfs file instead of using the 'airtime' file.
[Johannes:]
This effectively disables AQL for iwlwifi, where it fixes a number of
issues:
* TSO in iwlwifi is causing underflows and associated warnings in AQL
* HE (802.11ax) rates aren't reported properly so at HE rates, AQL could
never have a valid estimate (it'd use 6 Mbps instead of up to 2400!)
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191212111437.224294-1-toke@redhat.com
Fixes: 3ace10f5b5 ("mac80211: Implement Airtime-based Queue Limit (AQL)")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first_interrupt field is accessed in ena_intr_msix_io() upon
receiving an interrupt.The rx_ring and tx_ring fields of napi can
be NULL when receiving interrupt for xdp queues. This patch fixes
the issue by moving the field to the ena_napi struct.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the XDP_TX action in the ena driver. We allocate
separate tx queues for the XDP_TX. We currently allow xdp only when
there is enough queues to allocate for xdp.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit implements the basic functionality of drop/pass logic in the
ena driver.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver doesn't accommodate the configuration for max number
of multicast mac addresses, in such particular case it leaves
the device with improper/invalid multicast configuration state,
causing connectivity issues (in lacp bonding like scenarios).
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.
Fixes: ce85e13ad6 ("lan78xx: Update to use phylib instead of mii_if_info.")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some 1000BASE-T PHY modules take a while for the PHY to wake up.
Retry the probe a number of times before deciding that the module has
no PHY.
Tested with:
Sourcephotonics SPGBTXCNFC - PHY takes less than 50ms to respond.
Champion One 1000SFPT - PHY takes about 200ms to respond.
Mikrotik S-RJ01 - no PHY
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename sm_retries as sm_fault_retries, as this is what this member is
tracking.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via
the normal I2C address. Detect 10G BASE-T PHYs which may have an
accessible PHY and probe for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a rudimentary Clause 45 driver for the BCM84881 PHY, found on
Methode DM7052 SFPs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM84881 does not appear to send the SGMII control word
when operating in SGMII mode, which causes network adapters to fail
to link with the PHY, or decide to operate at fixed 1G speed, even if
the PHY negotiated 100M.
Work around this by detecting the Broadcom BCM84881 and switch to phy
mode rather than inband mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing whether we need to delay the MAC configuration because a module
may have a PHY is useful to phylink to allow NBASE-T modules to work on
systems supporting no more than 2.5G speeds.
This commit allows us to delay such configuration until after the PHY
has been probed by recording the parsed capabilities, and if the module
may have a PHY, doing no more until the module_start() notification is
called. At that point, we either have a PHY, or we don't.
We move the PHY-based setup a little later, and use the PHYs support
capabilities rather than the EEPROM parsed capabilities to determine
whether we can support the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the configuration step from phylink_sfp_module_insert() so
we can re-use this later.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split link_an_mode between the configured setting and the current
operating setting. This is an important distinction to make when we
need to configure PHY mode for a plugged SFP+ module that does not
use in-band signalling.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP+ modules have Clause 45 PHYs embedded on them, which need a
little more handling in order to ensure that they are correctly setup,
as they switch the PHY link mode according to the negotiated speed.
With Clause 22 PHYs, we assumed that they would operate in SGMII mode,
but this assumption is now false. Adapt phylink to support Clause 45
PHYs on SFP+ modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support Clause 45 PHYs on SFP+ modules, which have an
indeterminant phy interface mode, we need to be able to call
phylink_bringup_phy() with a different interface mode to that used when
binding the PHY. Reduce __phylink_connect_phy() to an attach operation,
and move the call to phylink_bringup_phy() to its call sites.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP+ modules have PHYs on them just like SFP modules do, except
they are Clause 45 PHYs. The I2C protocol used to access them is
modified slightly in order to send the device address and 16-bit
register index.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move phy_start() and phy_stop() into the module_start and module_stop
notifications in phylink, rather than having them in the SFP code.
This gives phylink responsibility for controlling the PHY, rather
than having SFP start and stop the PHY state machine.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with some copper modules, we can't positively know the
module capabilities are until we have probed the PHY. Without the full
capabilities, we may end up failing a module that we could otherwise
drive with a restricted set of capabilities.
An example of this would be a module with a NBASE-T PHY plugged into
a host that supports phy interface modes 2500BASE-X and SGMII. The
PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes,
which means a subset of the capabilities are compatible with the host.
However, reading the module EEPROM leads us to believe that the module
only supports ethtool link mode 10GBASE-T, which is incompatible with
the host - and thus results in the module being rejected.
This patch adds an extra notification which are triggered after the
SFP module's PHY probe, and a corresponding notification just before
the PHY is removed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications. Split these constants from the enum, and
rename them to indicate that they're defined by SFF-8024.
Add and use updated SFF-8024 extended compliance code definitions for
10GBASE-T, 5GBASE-T and 2.5GBASE-T modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need the EEPROM ID to derive the phy interface mode as we can
derive it merely from the ethtool link modes. Remove the EEPROM ID
argument to sfp_select_interface().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this
is probably an incorrect assumption. In any case, sfp_parse_support()
will fail such a module. Let's stop pretending we support these
modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netpoll the napi handler could be called with budget equal to zero.
Current ENA napi handler doesn't take that into consideration.
The napi handler handles Rx packets in a do-while loop.
Currently, the budget check happens only after decrementing the
budget, therefore the napi handler, in rare cases, could run over
MAX_INT packets.
In addition to that, this moves all budget related variables to int
calculation and stop mixing u32 to avoid ambiguity
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 has a separate region known as high priority filter region
that allows classifying packets going through ULD path. So,
query firmware for HPFILTER resources and enable the high
priority offload filter support when it is available.
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF driver also needs to create the health reporters since
VFs are also involved in firmware reset and recovery. Modify
bnxt_dl_register() and bnxt_dl_unregister() so that they can
be called by the VFs to register/unregister devlink. Only the PF
will register the devlink parameters. With devlink registered,
we can now create the health reporters on the VFs.
Fixes: 6763c779c2 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the logic to properly check the fw capabilities and create the
devlink health reporters only when needed. The current code creates
the reporters unconditionally as long as bp->fw_health is valid, and
that's not correct.
Call bnxt_dl_fw_reporters_create() directly from the init and reset
code path instead of from bnxt_dl_register(). This allows the
reporters to be adjusted when capabilities change. The same
applies to bnxt_dl_fw_reporters_destroy().
Fixes: 6763c779c2 ("bnxt_en: Add new FW devlink_health_reporter")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After fixing the allocation of bp->fw_health in the previous patch,
the driver will not go through the fw reset and recovery code paths
if bp->fw_health allocation fails. So we can now remove the
unnecessary NULL checks.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bp->fw_health needs to be allocated for either the firmware initiated
reset feature or the driver initiated error recovery feature. The
current code is not allocating bp->fw_health for all the necessary cases.
This patch corrects the logic to allocate bp->fw_health correctly when
needed. If allocation fails, we clear the feature flags.
We also add the the missing kfree(bp->fw_health) when the driver is
unloaded. If we get an async reset message from the firmware, we also
need to make sure that we have a valid bp->fw_health before proceeding.
Fixes: 07f83d72d2 ("bnxt_en: Discover firmware error recovery capabilities.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will trigger new context memory to be rediscovered and allocated
during the re-probe process after a firmware reset. Without this, the
newly reset firmware does not have valid context memory and the driver
will eventually fail to allocate some resources.
Fixes: ec5d31e3c1 ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic needs to check both bp->total_irqs and the reserved IRQs in
hw_resc->resv_irqs if applicable and see if both are enough to cover
the L2 and RDMA requested vectors. The current code is only checking
bp->total_irqs and can fail in some code paths, such as the TX timeout
code path with the RDMA driver requesting vectors after recovery. In
this code path, we have not reserved enough MSIX resources for the
RDMA driver yet.
Fixes: 75720e6323 ("bnxt_en: Keep track of reserved IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device stats are currently hard coded in the PCI BAR0 layout.
Add a ability to read them from the TLV area instead.
Names for the stats are maintained by the driver, and their
meaning documented. This allows us to more easily add and
remove device stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a software TX timestamp and add it to the ethtool query
interface.
skb_tx_timestamp() is also needed if one would like to use PHY
timestamping.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for v5.6. Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
We need to reset the NIC after setting the bits to enable power
gating and that cannot be done too late in the flow otherwise it
cleans other registers and things that were already configured,
causing initialization to fail.
In order to fix this, move the function to the common code in trans.c
so it can be called directly from there at an earlier point, just
after the reset we already do during initialization.
Fixes: 9a47cb9883 ("iwlwifi: pcie: add workaround for power gating in integrated 22000")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205719
Cc: stable@ver.kernel.org # 5.4+
Reported-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 968dcfb490.
Both that commit and commit 809805a820
attempted to fix the same bug (dead assignments to the local variable
cfg), but they did so in incompatible ways. When they were both merged,
independently of each other, the combination actually caused the bug to
reappear, leading to a firmware crash on boot for some cards.
https://bugzilla.kernel.org/show_bug.cgi?id=205719
Signed-off-by: Anders Kaseorg <andersk@mit.edu>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns:
../drivers/net/ppp/ppp_async.c:877:6: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
ap->rpkt = skb;
^
../drivers/net/ppp/ppp_async.c:875:5: note: previous statement is here
if (!skb)
^
1 warning generated.
This warning occurs because there is a space before the tab on this
line. Clean up this entire block's indentation so that it is consistent
with the Linux kernel coding style and clang no longer warns.
Fixes: 6722e78c90 ("[PPP]: handle misaligned accesses")
Link: https://github.com/ClangBuiltLinux/linux/issues/800
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
../drivers/net/ethernet/smsc/smc911x.c:939:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if (!lp->ctl_rfduplx)
^
../drivers/net/ethernet/smsc/smc911x.c:936:2: note: previous statement
is here
if (lp->ctl_rspeed != 100)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 0a0c72c911 ("[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips")
Link: https://github.com/ClangBuiltLinux/linux/issues/796
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
../drivers/net/ethernet/dec/tulip/uli526x.c:1812:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch (mode) {
^
../drivers/net/ethernet/dec/tulip/uli526x.c:1809:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
../drivers/net/ethernet/dec/tulip/dmfe.c:2217:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch(mode) {
^
../drivers/net/ethernet/dec/tulip/dmfe.c:2214:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
This warning occurs because there is a space before the tab on these
lines. Remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
While we are here, adjust the default block in dmfe_init_module to have
a proper break between the label and assignment and add a space between
the switch and opening parentheses to avoid a checkpatch warning.
Fixes: e1c3e50140 ("[PATCH] initialisation cleanup for ULI526x-net-driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/795
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code changes the TI specific ti,fifo-depth to the common
tx-fifo-depth property. The tx depth is applicable for both RGMII and
SGMII modes of operation.
rx-fifo-depth was added as well but this is only applicable for SGMII
mode.
So in summary
if RGMII mode write tx fifo depth only
if SGMII mode write both rx and tx fifo depths
If the property is not populated in the device tree then set the value
to the default values.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fjes_acpi_add() misses a check for platform_device_register_simple().
Add a check to fix it.
Fixes: 658d439b22 ("fjes: Introduce FUJITSU Extended Socket Network Device driver")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Nokia GPON module can hold tx-fault active while it is initialising
which can take up to 60s. Avoid this causing the module to be declared
faulty after the SFP MSA defined non-cooled module timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable rc is assigned with a value that is never read and
it is re-assigned a new value later on. The assignment is redundant
and can be removed. Clean up multiple occurrances of this pattern.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI CPSW(s) driver produces warning with DMA API debug options enabled:
WARNING: CPU: 0 PID: 1033 at kernel/dma/debug.c:1025 check_unmap+0x4a8/0x968
DMA-API: cpsw 48484000.ethernet: device driver frees DMA memory with different size
[device address=0x00000000abc6aa02] [map size=64 bytes] [unmap size=42 bytes]
CPU: 0 PID: 1033 Comm: ping Not tainted 5.3.0-dirty #41
Hardware name: Generic DRA72X (Flattened Device Tree)
[<c0112c60>] (unwind_backtrace) from [<c010d270>] (show_stack+0x10/0x14)
[<c010d270>] (show_stack) from [<c09bc564>] (dump_stack+0xd8/0x110)
[<c09bc564>] (dump_stack) from [<c013b93c>] (__warn+0xe0/0x10c)
[<c013b93c>] (__warn) from [<c013b9ac>] (warn_slowpath_fmt+0x44/0x6c)
[<c013b9ac>] (warn_slowpath_fmt) from [<c01e0368>] (check_unmap+0x4a8/0x968)
[<c01e0368>] (check_unmap) from [<c01e08a8>] (debug_dma_unmap_page+0x80/0x90)
[<c01e08a8>] (debug_dma_unmap_page) from [<c0752414>] (__cpdma_chan_free+0x114/0x16c)
[<c0752414>] (__cpdma_chan_free) from [<c07525c4>] (__cpdma_chan_process+0x158/0x17c)
[<c07525c4>] (__cpdma_chan_process) from [<c0753690>] (cpdma_chan_process+0x3c/0x5c)
[<c0753690>] (cpdma_chan_process) from [<c0758660>] (cpsw_tx_mq_poll+0x48/0x94)
[<c0758660>] (cpsw_tx_mq_poll) from [<c0803018>] (net_rx_action+0x108/0x4e4)
[<c0803018>] (net_rx_action) from [<c010230c>] (__do_softirq+0xec/0x598)
[<c010230c>] (__do_softirq) from [<c0143914>] (do_softirq.part.4+0x68/0x74)
[<c0143914>] (do_softirq.part.4) from [<c0143a44>] (__local_bh_enable_ip+0x124/0x17c)
[<c0143a44>] (__local_bh_enable_ip) from [<c0871590>] (ip_finish_output2+0x294/0xb7c)
[<c0871590>] (ip_finish_output2) from [<c0875440>] (ip_output+0x210/0x364)
[<c0875440>] (ip_output) from [<c0875e2c>] (ip_send_skb+0x1c/0xf8)
[<c0875e2c>] (ip_send_skb) from [<c08a7fd4>] (raw_sendmsg+0x9a8/0xc74)
[<c08a7fd4>] (raw_sendmsg) from [<c07d6b90>] (sock_sendmsg+0x14/0x24)
[<c07d6b90>] (sock_sendmsg) from [<c07d8260>] (__sys_sendto+0xbc/0x100)
[<c07d8260>] (__sys_sendto) from [<c01011ac>] (__sys_trace_return+0x0/0x14)
Exception stack(0xea9a7fa8 to 0xea9a7ff0)
...
The reason is that cpdma_chan_submit_si() now stores original buffer length
(sw_len) in CPDMA descriptor instead of adjusted buffer length (hw_len)
used to map the buffer.
Hence, fix an issue by passing correct buffer length in CPDMA descriptor.
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: 6670acacd5 ("net: ethernet: ti: davinci_cpdma: add dma mapped submit")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
In case the driver vetoes the addition of an IPv6 multipath route, the
IPv6 stack will emit delete notifications for the sibling routes that
were already added to the FIB trie. Since these siblings are not present
in hardware, a warning will be generated.
Have the driver ignore notifications for routes it does not have.
Fixes: ebee3cad83 ("ipv6: Add IPv6 multipath notifications for add / replace")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_cleanup() has not been used for seven years, and was a wrong design.
Messing with shared pointer in bond_neigh_init() without proper
memory barriers would at least trigger syzbot complains eventually.
It is time to remove this stuff.
Fixes: b63b70d877 ("IPoIB: Use a private hash table for path lookup in xmit path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl3s3dwTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIKhhB/sE+kGrGECa6DSehxKsSTCvh/5AGw2U
AGh+AHgpfCRKOPNBeN0yKCdBVSE40fURsIjNvn5SDZ1cY8tUOVCJAyUU31MfgzkW
b+Xiro5iOu6G/UpfZgMCeGV617FZg/65rz7ylwNzzA7zuUcoml6o4A55/QUFNIXx
juDzhdKmpmLRQusekzbP9qyCgDGXv8/cPBloI+frzqaDU5bgS6Q3ldHe26lkQzNH
bwF6bCGpJYykuNFIrLoFpSuJ+7ttZhLexXCwsl90UfpwmHVvUgQKJuF8JVR1AF3x
5mjHWi3GFyi4aUL4yY4kU3cWWPse3MQLPt5QqMu56dW4UADp1k3FHByo
=YMzV
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.5-20191208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-12-08
this is a pull request of 13 patches for net/master.
The first two patches are by Dan Murphy. He adds himself as a maintainer to the
m-can MMIO and tcan SPI driver.
The next two patches the j1939 stack. The first one is by Oleksij Rempel and
fixes a locking problem found by the syzbot, the second one is by me an fixes a
mistake in the documentation.
Srinivas Neeli fixes missing RX CAN packets on CANFD2.0 in the xilinx driver.
Sean Nyekjaer fixes a possible deadlock in the the flexcan driver after
suspend/resume. Joakim Zhang contributes two patches for the flexcan driver
that fix problems with the low power enter/exit.
The next 4 patches all target the tcan part of the m_can driver. Sean Nyekjaer
adds the required delay after reset and fixes the device tree binding example.
Dan Murphy's patches make the wake-gpio optional.
In the last patch Xiaolong Huang fixes several kernel memory info leaks to the
USB device in the kvaser_usb_leaf driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WireGuard is a layer 3 secure networking tunnel made specifically for
the kernel, that aims to be much simpler and easier to audit than IPsec.
Extensive documentation and description of the protocol and
considerations, along with formal proofs of the cryptography, are
available at:
* https://www.wireguard.com/
* https://www.wireguard.com/papers/wireguard.pdf
This commit implements WireGuard as a simple network device driver,
accessible in the usual RTNL way used by virtual network drivers. It
makes use of the udp_tunnel APIs, GRO, GSO, NAPI, and the usual set of
networking subsystem APIs. It has a somewhat novel multicore queueing
system designed for maximum throughput and minimal latency of encryption
operations, but it is implemented modestly using workqueues and NAPI.
Configuration is done via generic Netlink, and following a review from
the Netlink maintainer a year ago, several high profile userspace tools
have already implemented the API.
This commit also comes with several different tests, both in-kernel
tests and out-of-kernel tests based on network namespaces, taking profit
of the fact that sockets used by WireGuard intentionally stay in the
namespace the WireGuard interface was originally created, exactly like
the semantics of userspace tun devices. See wireguard.com/netns/ for
pictures and examples.
The source code is fairly short, but rather than combining everything
into a single file, WireGuard is developed as cleanly separable files,
making auditing and comprehension easier. Things are laid out as
follows:
* noise.[ch], cookie.[ch], messages.h: These implement the bulk of the
cryptographic aspects of the protocol, and are mostly data-only in
nature, taking in buffers of bytes and spitting out buffers of
bytes. They also handle reference counting for their various shared
pieces of data, like keys and key lists.
* ratelimiter.[ch]: Used as an integral part of cookie.[ch] for
ratelimiting certain types of cryptographic operations in accordance
with particular WireGuard semantics.
* allowedips.[ch], peerlookup.[ch]: The main lookup structures of
WireGuard, the former being trie-like with particular semantics, an
integral part of the design of the protocol, and the latter just
being nice helper functions around the various hashtables we use.
* device.[ch]: Implementation of functions for the netdevice and for
rtnl, responsible for maintaining the life of a given interface and
wiring it up to the rest of WireGuard.
* peer.[ch]: Each interface has a list of peers, with helper functions
available here for creation, destruction, and reference counting.
* socket.[ch]: Implementation of functions related to udp_socket and
the general set of kernel socket APIs, for sending and receiving
ciphertext UDP packets, and taking care of WireGuard-specific sticky
socket routing semantics for the automatic roaming.
* netlink.[ch]: Userspace API entry point for configuring WireGuard
peers and devices. The API has been implemented by several userspace
tools and network management utility, and the WireGuard project
distributes the basic wg(8) tool.
* queueing.[ch]: Shared function on the rx and tx path for handling
the various queues used in the multicore algorithms.
* send.c: Handles encrypting outgoing packets in parallel on
multiple cores, before sending them in order on a single core, via
workqueues and ring buffers. Also handles sending handshake and cookie
messages as part of the protocol, in parallel.
* receive.c: Handles decrypting incoming packets in parallel on
multiple cores, before passing them off in order to be ingested via
the rest of the networking subsystem with GRO via the typical NAPI
poll function. Also handles receiving handshake and cookie messages
as part of the protocol, in parallel.
* timers.[ch]: Uses the timer wheel to implement protocol particular
event timeouts, and gives a set of very simple event-driven entry
point functions for callers.
* main.c, version.h: Initialization and deinitialization of the module.
* selftest/*.h: Runtime unit tests for some of the most security
sensitive functions.
* tools/testing/selftests/wireguard/netns.sh: Aforementioned testing
script using network namespaces.
This commit aims to be as self-contained as possible, implementing
WireGuard as a standalone module not needing much special handling or
coordination from the network subsystem. I expect for future
optimizations to the network stack to positively improve WireGuard, and
vice-versa, but for the time being, this exists as intentionally
standalone.
We introduce a menu option for CONFIG_WIREGUARD, as well as providing a
verbose debug log and self-tests via CONFIG_WIREGUARD_DEBUG.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: David Miller <davem@davemloft.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
Uninitialized Kernel memory can leak to USB devices.
Fix this by using kzalloc() instead of kmalloc().
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com>
Fixes: 7259124eac ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.19
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device has the ability to disable the wake-up pin option. The
wake-up pin can be either force to GND or Vsup and does not have to be
tied to a GPIO. In order for the device to not use the wake-up feature
write the register to disable the WAKE_CONFIG option.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to section "8.3.8 RST Pin" in the datasheet we are required to
wait >700us after the device is reset.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stop Mode is entered when Stop Mode is requested at chip level and
MCR[LPM_ACK] is asserted by the FlexCAN.
Double check with IP owner, the MCR[LPM_ACK] bit should be polled for
stop mode acknowledgment, not the acknowledgment from chip level which
is used to gate flexcan clocks.
This patch depends on:
b7603d080f ("can: flexcan: add low power enter/exit acknowledgment helper")
Fixes: 5f186c257f (can: flexcan: fix stop mode acknowledgment)
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The MCR[LPMACK] read-only bit indicates that FlexCAN is in a lower-power
mode (Disabled mode, Doze mode, Stop mode).
The CPU can poll this bit to know when FlexCAN has actually entered low
power mode. The low power enter/exit acknowledgment helper will reduce
code duplication for disabled mode, doze mode and stop mode.
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When suspending, and there is still CAN traffic on the interfaces the
flexcan immediately wakes the platform again. As it should :-). But it
throws this error msg:
[ 3169.378661] PM: noirq suspend of devices failed
On the way down to suspend the interface that throws the error message
calls flexcan_suspend() but fails to call flexcan_noirq_suspend(). That
means flexcan_enter_stop_mode() is called, but on the way out of suspend
the driver only calls flexcan_resume() and skips flexcan_noirq_resume(),
thus it doesn't call flexcan_exit_stop_mode(). This leaves the flexcan
in stop mode, and with the current driver it can't recover from this
even with a soft reboot, it requires a hard reboot.
This patch fixes the deadlock when using self wakeup, by calling
flexcan_exit_stop_mode() from flexcan_resume() instead of
flexcan_noirq_resume().
This also fixes another issue: CAN frames are received out-of-order in
first IRQ handler run after wakeup.
The problem is that the wakeup latency from frame reception to the IRQ
handler (where the CAN frames are sorted by timestamp) is much bigger
than the time stamp counter wrap around time. This means it's
impossible to sort the CAN frames by timestamp.
The reason is that the controller exits stop mode during noirq resume,
which means it receives frames immediately, but interrupt handling is
still not possible.
So exit stop mode during resume stage instead of noirq resume fixes this
issue.
Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CANFD2.0 core uses BRAM for storing acceptance filter ID(AFID) and MASK
(AFMASK)registers. So by default AFID and AFMASK registers contain random
data. Due to random data, we are not able to receive all CAN ids.
Initializing AFID and AFMASK registers with Zero before enabling
acceptance filter to receive all packets irrespective of ID and Mask.
Fixes: 0db9071353 ("can: xilinx: add can 2.0 support")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3b ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 also requires to enable RX for WoL.
v2: add missing Fixes tag
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit ef87f7da6b ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.
To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.
Fixes: ef87f7da6b ("net: phy: dp83867: move dt parsing to probe")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feab ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing NULL to pppoe_pernet causes a crash via BUG_ON.
Dereferencing net in net_generici() also has the same effect. This patch
removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl3pcFUACgkQSD+KveBX
+j4tNgf/VJ1FgeYn4INueeliFebX+8sgk7pA8zI5Wf3s0gzmCLulNeF8sK3sV7o4
U94dHauU1CZxTpI9P2AVJVQ5CnTi2GBjuEKHh1Rz9bVwU3N5D4miShtHUEI1PLna
VhLJiMSU1ffUerL66zgW+QYbPAKSlp+INysr+KeBBOwxoco4C17pGwJ9idpaHYnL
sdVsHVcWmD1fen+eSN/8i4RzqVFTjM3cCsMg1OJn8KuDH+z6bQZ9cOWWLn+hz9lc
uBZHZHvRFRTg1NeN1BFcMEL0RBoG0sTtfJLkVeyQxmLbmTeBPHDBIAJysqjAe1kY
OFvEnq5t3HScuZIxTd5yXQ3rHy1EIg==
=InW3
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-12-05
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.19:
('net/mlx5e: Query global pause state before setting prio2buffer')
For -stable v5.3
('net/mlx5e: Fix SFF 8472 eeprom length')
('net/mlx5e: Fix translation of link mode into speed')
('net/mlx5e: Fix freeing flow with kfree() and not kvfree()')
('net/mlx5e: ethtool, Fix analysis of speed setting')
('net/mlx5e: Fix TXQ indices to be sequential')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We may have found a bug in the nxp/lpc_eth.c driver. The function
platform_set_drvdata() is called twice, the second time it is called,
in lpc_mii_init(), it overwrites the struct net_device which should be
at pdev->dev->driver_data with pldat->mii_bus. When trying to remove
the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will
return the pldat->mii_bus pointer and try to use it as a struct
net_device pointer. This causes unregister_netdev to segfault and
generate a kernel BUG. Is this reproducible?
Signed-off-by: Daniel Martinez <linux@danielsmartinez.com>
Signed-off-by: Bruno Carneiro da Cunha <brunocarneirodacunha@usp.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to call pci_release_regions() in remove like that
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refer to the databook of DesignWare Cores Ethernet MAC Universal:
6.2.1.5 Register 4 (Transmit Descriptor List Address Register
If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.
The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_fprog_kern::len is in units of struct sock_filter, not bytes.
Fixes: 3e859adf36 ("compat_ioctl: unify copy-in of ppp filters")
Reported-by: syzbot+eb853b51b10f1befa0b7@syzkaller.appspotmail.com
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when set VF VLAN with command "ip link set <pf name>
vf <vf id> vlan <vlan id>", the VF ID 0 is handled as PF incorrectly,
which should be the first VF. This patch fixes it.
Fixes: 21e043cd81 ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, hns3_nic_maybe_stop_tx() uses skb_copy() to linearize a
SKB if the BD num required by the SKB does not meet the hardware
limitation, and it linearizes the SKB by allocating a new linearized SKB
and freeing the old SKB, if hns3_nic_maybe_stop_tx() returns -EBUSY
because there are no enough space in the ring to send the linearized
skb to hardware, the sch_direct_xmit() still hold reference to old SKB
and try to retransmit the old SKB when dev_hard_start_xmit() return
TX_BUSY, which may cause use after freed problem.
This patch fixes it by using __skb_linearize() to linearize the
SKB in hns3_nic_maybe_stop_tx().
Fixes: 51e8439f34 ("net: hns3: add 8 BD limit for tx flow")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is timing window between ring_space checking and
netif_stop_subqueue when transmiting a SKB, and the TX BD
cleaning may be executed during the time window, which may
caused TX queue not restarted problem.
This patch fixes it by rechecking the ring_space after
netif_stop_subqueue to make sure TX queue is restarted.
Also, the ring->next_to_clean is updated even when pkts is
zero, because all the TX BD cleaned may be non-SKB, so it
needs to check if TX queue need to be restarted.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "select NET_SWITCHDEV" vs "depends on NET_SWITCHDEV" to fix Kconfig
warning with CONFIG_COMPILE_TEST=y
WARNING: unmet direct dependencies detected for NET_SWITCHDEV
Depends on [n]: NET [=y] && INET [=n]
Selected by [y]:
- TI_CPSW_SWITCHDEV [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && (ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST [=y])
because TI_CPSW_SWITCHDEV blindly selects NET_SWITCHDEV even though
INET is not set/enabled, while NET_SWITCHDEV depends on INET.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
In cited commit, when prio tag mode is enabled, FTE creation fails
due to missing group with valid match criteria.
Hence,
(a) create prio tag group metadata_prio_tag_grp when prio tag is
enabled with match criteria for vlan push FTE.
(b) Rename metadata_grp to metadata_allmatch_grp to reflect its purpose.
Also when priority tag is enabled, delete metadata settings after
deleting ingress rules, which are using it.
Tide up rest of the ingress config code for unnecessary labels.
Fixes: 10652f3994 ("net/mlx5: Refactor ingress acl configuration")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When setting speed to 100G via ethtool (AN is set to off), only 25G*4 is
configured while the user, who has an advanced HW which supports
extended PTYS, expects also 50G*2 to be configured.
With this patch, when extended PTYS mode is available, configure
PTYS via extended fields.
Fixes: 4b95840a6c ("net/mlx5e: Fix matching of speed to PRM link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a missing value in translation of PTYS ext_eth_proto_oper to its
corresponding speed. When ext_eth_proto_oper bit 10 is set, ethtool
shows unknown speed. With this fix, ethtool shows speed is 100G as
expected.
Fixes: a08b4ed137 ("net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It could be neigh update flow took a refcount on peer flow so
sometimes we cannot release peer flow even if parent flow is
being freed now.
Fixes: 5a7e5bcb66 ("net/mlx5e: Extend tc flow struct with reference counter")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flows are allocated with kzalloc() so free with kfree().
Fixes: 04de7dda73 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
SFF 8472 eeprom length is 512 bytes. Fix module info return value to
support 512 bytes read.
Fixes: ace329f4ab ("net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the user changes prio2buffer mapping while global pause is
enabled, mlx5 driver incorrectly sets all active buffers
(buffer that has at least one priority mapped) to lossy.
Solution:
If global pause is enabled, set all the active buffers to lossless
in prio2buffer command.
Also, add error message when buffer size is not enough to meet
xoff threshold.
Fixes: 0696d60853 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cited patch changed (channel index, tc) => (TXQ index) mapping to be a
static one, in order to keep indices consistent when changing number of
channels or TCs.
For 32 channels (OOB) and 8 TCs, real num of TXQs is 256.
When reducing the amount of channels to 8, the real num of TXQs will be
changed to 64.
This indices method is buggy:
- Channel #0, TC 3, the TXQ index is 96.
- Index 8 is not valid, as there is no such TXQ from driver perspective
(As it represents channel #8, TC 0, which is not valid with the above
configuration).
As part of driver's select queue, it calls netdev_pick_tx which returns an
index in the range of real number of TXQs. Depends on the return value,
with the examples above, driver could have returned index larger than the
real number of tx queues, or crash the kernel as it tries to read invalid
address of SQ which was not allocated.
Fix that by allocating sequential TXQ indices, and hold a new mapping
between (channel index, tc) => (real TXQ index). This mapping will be
updated as part of priv channels activation, and is used in
mlx5e_select_queue to find the selected queue index.
The existing indices mapping (channel_tc2txq) is no longer needed, as it
is used only for statistics structures and can be calculated on run time.
Delete its definintion and updates.
Fixes: 8bfaf07f78 ("net/mlx5e: Present SW stats when state is not opened")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Since commit 2b3e88ea65 ("net: phy: improve phy state checking")
phy_start_aneg() expects phy state to be >= PHY_UP. Call phy_start()
before calling phy_start_aneg() during probe so that autonegotiation
is initiated.
As phy_start() takes care of calling phy_start_aneg(), drop the explicit
call to phy_start_aneg().
Network fails without this patch on Octeon TX.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The referenced commit below allowed more than one hwmon device to be
created per SFP, which is definitely not what we want. Avoid this by
only creating the hwmon device just as we transition to WAITDEV state.
Fixes: 139d3a212a ("net: sfp: allow modules with slow diagnostics to probe")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unbinding, we don't correctly tear down the module state, leaving
(for example) the hwmon registration behind. Ensure everything is
properly removed by sending a remove event at unbind.
Fixes: 6b0da5c9c1 ("net: sfp: track upstream's attachment state in state machine")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user has specified their own RSS hash key, don't
lose it across queue resets such as DOWN/UP, MTU change,
and number of channels change. This is fixed by moving
the key initialization to a little earlier in the lif
creation.
Also, let's clean up the RSS config a little better on
the way down by setting it all to 0.
Fixes: aa3198819b ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
As per linux can framework, driver not allowed to touch the skb memory
after can_put_echo_skb() call.
This patch fixes the same.
https://www.spinics.net/lists/linux-can/msg02199.html
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the CAN bus clock is provided from the clock wizard, clock wizard
driver may not be available when can driver probes resulting to the
error message "bus clock not found error".
As this error message is not very useful to the end user, skip printing
in the case of deferred probe.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
USB completion handlers are called in atomic context and must
specifically not allocate memory using GFP_KERNEL.
Fixes: 9f2d3eae88 ("can: ucan: add driver for Theobroma Systems UCAN devices")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Slcan_open doesn't clean-up device which registration failed from the
slcan_devs device list. On next open this list is iterated and freed
device is accessed. Fix this by calling slc_free_netdev in error path.
Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was
identified in slip_open by syzboz. Same bug is in slcan.c. Here is the
trace from the Syzbot slip report:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:634
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
sl_sync drivers/net/slip/slip.c:725 [inline]
slip_open+0xecd/0x11b7 drivers/net/slip/slip.c:801
tty_ldisc_open.isra.0+0xa3/0x110 drivers/tty/tty_ldisc.c:469
tty_set_ldisc+0x30e/0x6b0 drivers/tty/tty_ldisc.c:596
tiocsetd drivers/tty/tty_io.c:2334 [inline]
tty_ioctl+0xe8d/0x14f0 drivers/tty/tty_io.c:2594
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xdb6/0x13e0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: ed50e1600b ("slcan: Fix memory leak in error path")
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Miller <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of things to
convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just need
to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a variety of
systems (and to not take over huge systems entirely in particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need to
load a lot of paper.
- A script and documentation making it easy for maintainers to add Link:
tags at commit time.
Also included is the removal of a bunch of spurious CR characters.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl3j5B0PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YtBcH/jIN2cO8/0YW2rjVT+1G6ytSdFUKx5WJ/lpf
5uBeCvuCeYhtCB6+BgnXvjykJ7jDW11/NJNjWqz/gsvD5l5FJK1rXarI/oz2Klyi
kcPtDmBF/ki4wz9qXzEpa0vg8LXdjeys50S1vE75qCzxZoPP7YjuRbPnLrlIJukv
JbDVi4p9kxgeHfRB4+BHOe5rFwA3mMmaxKNIX34Y+UUO2KZ0g/yUi1bAaQwQAdt+
PsORmkVQ8Puh3K9xRIr7dYlcWBlBiPqzYdvDgTVxSjrxdK6wjYjSgVk2VjC5MBUN
mTSTWgyfsIcD/76/s8tq7ZRl2fw+SkCSkFo79Rb/hJwDTb7Vnng=
=LPBr
-----END PGP SIGNATURE-----
Merge tag 'docs-5.5a' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"Here are the main documentation changes for 5.5:
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of
things to convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just
need to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a
variety of systems (and to not take over huge systems entirely in
particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need
to load a lot of paper.
- A script and documentation making it easy for maintainers to add
Link: tags at commit time.
Also included is the removal of a bunch of spurious CR characters"
* tag 'docs-5.5a' of git://git.lwn.net/linux: (91 commits)
docs: remove a bunch of stray CRs
docs: fix up the maintainer profile document
libnvdimm, MAINTAINERS: Maintainer Entry Profile
Maintainer Handbook: Maintainer Entry Profile
MAINTAINERS: Reclaim the P: tag for Maintainer Entry Profile
docs, parallelism: Rearrange how jobserver reservations are made
docs, parallelism: Do not leak blocking mode to other readers
docs, parallelism: Fix failure path and add comment
Documentation: Remove bootmem_debug from kernel-parameters.txt
Documentation: security: core.rst: fix warnings
Documentation/process/howto/kokr: Update for 4.x -> 5.x versioning
Documentation/translation: Use Korean for Korean translation title
docs/memory-barriers.txt: Remove remaining references to mmiowb()
docs/memory-barriers.txt/kokr: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt/kokr: Fix style, spacing and grammar in I/O section
Documentation/kokr: Kill all references to mmiowb()
docs/memory-barriers.txt/kokr: Rewrite "KERNEL I/O BARRIER EFFECTS" section
docs: Add initial documentation for devfreq
Documentation: Document how to get links with git am
docs: Add request_irq() documentation
...
mwifiex_process_tdls_action_frame() without checking
the incoming tdls infomation element's vality before use it,
this may cause multi heap buffer overflows.
Fix them by putting vality check before use it.
IE is TLV struct, but ht_cap and ht_oper aren’t TLV struct.
the origin marvell driver code is wrong:
memcpy(&sta_ptr->tdls_cap.ht_oper, pos,....
memcpy((u8 *)&sta_ptr->tdls_cap.ht_capb, pos,...
Fix the bug by changing pos(the address of IE) to
pos+2 ( the address of IE value ).
Signed-off-by: qize wang <wangqize888888888@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation always use default eeprom mac address to
configure device registers even if it is updated using
mt76_eeprom_override. Fix it initializing macaddr filed of mt76_dev data
structure with eeprom mac address and running mt76_eeprom_override
before mt76x02_mac_setaddr
Fixes: d1bc9bf207 ("mt76: mt76x0: eeprom: add support for MAC address from OF")
Tested-by: Kevin Schmidt <kevin.patrick.schmidt@googlemail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some sdio chips of rome QCA6174's regulatory domain code of EEPROM is
empty, then ath_is_world_regd will return false for this case, and
it will lead function __ath_reg_dyn_country not work, thus the regdomain
will not update for NL80211_REGDOM_SET_BY_COUNTRY_IE type, it result
ath10k set the same regdomain/reg_5ghz_ctl/reg_2ghz_ctl to firmware,
then the tx power will not changed with different regdomain's AP. The
regulatory domain code of EEPROM of some QCA6174 PCIE chip is 0x6c, it
means world wide regdomain, for this chip, it does not have the issue.
For empty reulatory domain code chip, set it to world regulatory domain
in functio ath_regd_sanitize, then it will fix the issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For max bundle size 32, the bundle mask is not same with 8/16.
Change it to match the max bundle size of htc. Otherwise it
will not match with firmware, for example, when bundle count
is 17, then flags of ath10k_htc_hdr is 0x4, if without this
patch, it will be considered as non-bundled packet because it
does not have mask 0xF0, then trigger error message later:
payload length 56747 exceeds max htc length: 4088.
htc->max_msgs_per_htc_bundle is the min value of
HTC_HOST_MAX_MSG_PER_RX_BUNDLE and
msg->ready_ext.max_msgs_per_htc_bundle of ath10k_htc_wait_target,
it will be sent to firmware later in ath10k_htc_start, then
firmware will use it as the final max rx bundle count, in
WLAN.RMH.4.4.1-00029, msg->ready_ext.max_msgs_per_htc_bundle
is 32, it is same with HTC_HOST_MAX_MSG_PER_RX_BUNDLE, so the
final max rx bundle count will be set to 32 in firmware.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Fixes: 224776520e ("ath10k: change max RX bundle size from 8 to 32 for sdio")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For tcp RX, the quantity of tcp acks to remote is 1/2 of the quantity
of tcp data from remote, then it will have many small length packets
on TX path of sdio bus, then it reduce the RX packets's bandwidth of
tcp.
This patch enable napi on RX path, then the RX packet of tcp will not
feed to tcp stack immeditely from mac80211 since GRO is enabled by
default, it will feed to tcp stack after napi complete, if rx bundle
is enabled, then it will feed to tcp stack one time for each bundle
of RX. For example, RX bundle size is 32, then tcp stack will receive
one large length packet, its length is neary 1500*32, then tcp stack
will send a tcp ack for this large packet, this will reduce the tcp
acks ratio from 1/2 to 1/32. This results in significant performance
improvement for tcp RX.
Tcp rx throughout is 240Mbps without this patch, and it arrive 390Mbps
with this patch. The cpu usage has no obvious difference with and
without NAPI.
call stack for each RX packet on GRO path:
(skb length is about 1500 bytes)
skb_gro_receive ([kernel.kallsyms])
tcp4_gro_receive ([kernel.kallsyms])
inet_gro_receive ([kernel.kallsyms])
dev_gro_receive ([kernel.kallsyms])
napi_gro_receive ([kernel.kallsyms])
ieee80211_deliver_skb ([mac80211])
ieee80211_rx_handlers ([mac80211])
ieee80211_prepare_and_rx_handle ([mac80211])
ieee80211_rx_napi ([mac80211])
ath10k_htt_rx_proc_rx_ind_hl ([ath10k_core])
ath10k_htt_rx_pktlog_completion_handler ([ath10k_core])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
call stack for napi complete and send tcp ack from tcp stack:
(skb length is about 1500*32 bytes)
_tcp_ack_snd_check ([kernel.kallsyms])
tcp_v4_do_rcv ([kernel.kallsyms])
tcp_v4_rcv ([kernel.kallsyms])
local_deliver_finish ([kernel.kallsyms])
ip_local_deliver ([kernel.kallsyms])
ip_rcv_finish ([kernel.kallsyms])
ip_rcv ([kernel.kallsyms])
netif_receive_skb_core ([kernel.kallsyms])
netif_receive_skb_one_core([kernel.kallsyms])
netif_receive_skb ([kernel.kallsyms])
netif_receive_skb_internal ([kernel.kallsyms])
napi_gro_complete ([kernel.kallsyms])
napi_gro_flush ([kernel.kallsyms])
napi_complete_done ([kernel.kallsyms])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
__softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) Fix several scatter gather list issues in kTLS code, from Jakub
Kicinski.
2) macb driver device remove has to kill the hresp_err_tasklet. From
Chuhong Yuan.
3) Several memory leak and reference count bug fixes in tipc, from Tung
Nguyen.
4) Fix mlx5 build error w/o ipv6, from Yue Haibing.
5) Fix jumbo frame and other regressions in r8169, from Heiner
Kallweit.
6) Undo some BUG_ON()'s and replace them with WARN_ON_ONCE and proper
error propagation/handling. From Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (24 commits)
openvswitch: remove another BUG_ON()
openvswitch: drop unneeded BUG_ON() in ovs_flow_cmd_build_info()
net: phy: realtek: fix using paged operations with RTL8105e / RTL8208
r8169: fix resume on cable plug-in
r8169: fix jumbo configuration for RTL8168evl
net: emulex: benet: indent a Kconfig depends continuation line
selftests: forwarding: fix race between packet receive and tc check
net: sched: fix `tc -s class show` no bstats on class with nolock subqueues
net: ethernet: ti: ale: ensure vlan/mdb deleted when no members
net/mlx5e: Fix build error without IPV6
selftests: pmtu: use -oneline for ip route list cache
tipc: fix duplicate SYN messages under link congestion
tipc: fix wrong timeout input for tipc_wait_for_cond()
tipc: fix wrong socket reference counter after tipc_sk_timeout() returns
tipc: fix potential memory leak in __tipc_sendmsg()
net: macb: add missed tasklet_kill
selftests: bpf: correct perror strings
selftests: bpf: test_sockmap: handle file creation failures gracefully
net/tls: use sg_next() to walk sg entries
net/tls: remove the dead inplace_crypto code
...
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
It was reported [0] that since the referenced commit a warning is
triggered in phylib that complains about paged operations being used
with a PHY driver that doesn't support this. The commit isn't wrong,
just for one chip version (RTL8105e) no dedicated PHY driver exists
yet. So add the missing PHY driver.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 3a129e3f9a ("r8169: switch to phylib functions in more places")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported [0] that network doesn't wake up on cable plug-in with
certain chip versions. Reason is that on these chip versions the PHY
doesn't detect cable plug-in when being in power-down mode. So prevent
the PHY from powering down if WoL is enabled.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 95fb8bb318 ("net: phy: force phy suspend when calling phy_stop")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan reported [0] that network is broken since the referenced commit
when using jumbo frames. This commit isn't wrong, it just revealed
another issue that has been existing before. According to the vendor
driver the RTL8168e-specific jumbo config doesn't apply for RTL8168evl.
[0] https://lkml.org/lkml/2019/11/30/119
Fixes: 4ebcb113ed ("r8169: fix jumbo packet handling on resume from suspend")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Tested-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Hibernation support (Dexuan Cui).
- Latency testing framework (Branden Bonaby).
- Decoupling Hyper-V page size from guest page size (Himadri Pandya).
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE4n5dijQDou9mhzu83qZv95d3LNwFAl3f5YIACgkQ3qZv95d3
LNzBww/8Cpv/BnOs2cp56OhC+2++3YlWfmxGnvQb9h52weElgr1AZF33lAynp8BZ
YssOcDnS/G2iAkNDffbQA7s3WTwIjP1weJibOeKbtcXp4SuhNR3gnJafufNddNDv
bw8ZReLQV7hy3sHb3OUx0aJk5Mssp0N9ZpxRilyIpLELPfVp63gFebq6s1MQYljk
BAiNO4SKqsGQGZApt2F4Cc3hX2wU2ZfiDm6SifXiLYITGnvilIn7XFIht+2jJBWS
CdzRoGXcwhQhlj68XWlc89SOzJb7vVUMO1sr84psfbQ2LbhJU8lfJKRJ4b4lR07Z
Uv5FYxjr14S65fv7DkzCfWU+uPN/sObG4pPXihlfqcTraOvYLQ6/x8cw+9tGZg4H
aTtnF40hnO81aKsvPAeIsSzVkoyPaSrt7KKhk+Bw/5EUDTTNp6EbIuL4xwnKt6Rt
2UpA5HM9guQqNb6OZrjlpZfJgd9bNP4CZLBTfOukmnZpONKr2Wv3wubcwQJ8ibQc
1WZ5SfN2Wmg999Ski7j9qzHk0tWJxa6SX+2NLEHRKxy2nJSJ1zlAr//bznMyMgH/
yKPDaSkOFoy0aqiTKV2WzuOY6FGXTrSo5vq8YAgYRgp3xB+5+7zLeqlj3ipXhLYE
HH/eqB27eSnvi0jpub4TbszGJG0o4Z1aYx3aHYYqrOfWX/A5Vls=
=oJGE
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Sasha Levin:
- support for new VMBus protocols (Andrea Parri)
- hibernation support (Dexuan Cui)
- latency testing framework (Branden Bonaby)
- decoupling Hyper-V page size from guest page size (Himadri Pandya)
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (22 commits)
Drivers: hv: vmbus: Fix crash handler reset of Hyper-V synic
drivers/hv: Replace binary semaphore with mutex
drivers: iommu: hyperv: Make HYPERV_IOMMU only available on x86
HID: hyperv: Add the support of hibernation
hv_balloon: Add the support of hibernation
x86/hyperv: Implement hv_is_hibernation_supported()
Drivers: hv: balloon: Remove dependencies on guest page size
Drivers: hv: vmbus: Remove dependencies on guest page size
x86: hv: Add function to allocate zeroed page for Hyper-V
Drivers: hv: util: Specify ring buffer size using Hyper-V page size
Drivers: hv: Specify receive buffer size using Hyper-V page size
tools: hv: add vmbus testing tool
drivers: hv: vmbus: Introduce latency testing
video: hyperv: hyperv_fb: Support deferred IO for Hyper-V frame buffer driver
video: hyperv: hyperv_fb: Obtain screen resolution from Hyper-V host
hv_netvsc: Add the support of hibernation
hv_sock: Add the support of hibernation
video: hyperv_fb: Add the support of hibernation
scsi: storvsc: Add the support of hibernation
Drivers: hv: vmbus: Add module parameter to cap the VMBus version
...
Indent a Kconfig continuation line to improve readability.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The recently updated ALE APIs cpsw_ale_del_mcast() and
cpsw_ale_del_vlan_modify() have an issue and will not delete ALE entry even
if VLAN/mcast group has no more members. Hence fix it here and delete ALE
entry if !port_mask.
The issue affected only new cpsw switchdev driver.
Fixes: e85c143707 ("net: ethernet: ti: ale: modify vlan/mdb api for switchdev")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If IPV6 is not set and CONFIG_MLX5_ESWITCH is y,
building fails:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c:322:5: error: redefinition of mlx5e_tc_tun_create_header_ipv6
int mlx5e_tc_tun_create_header_ipv6(struct mlx5e_priv *priv,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.c:7:0:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_tun.h:67:1: note: previous definition of mlx5e_tc_tun_create_header_ipv6 was here
mlx5e_tc_tun_create_header_ipv6(struct mlx5e_priv *priv,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Use #ifdef to guard this, also move mlx5e_route_lookup_ipv6
to cleanup unused warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e689e998e1 ("net/mlx5e: TC, Stub out ipv6 tun create header function")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware expects all the required REO destination rings setup
while processing wmi_init command. Not doing this causes connected
stations getting disconnected and not able to connect back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is to prepare REO ring setup before sending wmi_init command.
Firmware expects all the required REO rings to be setup while processing
wmi_init command. But as per the current initialization sequence, REO ring
configurations are done only after wmi_init command is sent.
Also refactoring ath11k_mac_create() into ath11k_mac_alloc() and
ath11k_mac_register() to it mac80211 hw structure available before sending
wmi_init command.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently HTT_PPDU_STATS_TAG_USR_COMPLTN_ACK_BA_STATUS tag of PPDU stats
doesn't have valid success bytes info of management frames.
So skip update peer stats for management packets.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update tx duration in station info form PPDU stats
so that users can dump tx duration of the station.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Guard interval value which comes from VHT_SIG_A TLV has a mapping
where value 0 corresponds to LGI, 1 and 3 corresponds to SGI.
Value 3 which is SGI(0.4us) in VHT was incorrectly mapped to a GI
of 3.2us(only applicable in HE) resulting in incorrect rx GI stats.
Fixing the mapping.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove tail check to avoid last amsdu leak.
recycle skb in ppdu id wrap around case
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adverise MPDU start spacing as no restriction in ht capabilities,
Since IPQ8074 hw support all sorts of mpdu start spcing. With this
observed minor uplink performance improvement in lower data frame
size case with Veriwave clients.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set the number of tx and rx chains properly on drv_set_antenna().
This will ensure the related ht/vht/he caps are properly recalculated
based on the tx/rx chains set.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add necessary peer assoc params in WMI debug message
while sending the peer assoc command to firmware
to aid in debugging.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
qmi firmware ready event start to initialize the core modules and
the sequence executed with mutex lock. In case of any failure
mutex should be unlocked otherwise it will hang during the recovery.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add the support to control the transmit power
for traffic to a station associated with the AP.
Underlying firmware will enforce that the maximum tx power will
be based on the regulatory requirements. If the user given
transmit power is greater than the allowed tx power in the given
channel, then the firmware will use the maximum tx power in the
same channel.
Max and Min tx power values will depends on number of tx chain
masks. The allowed tx power range values are from 6 to 23.
When 0 is sent to the firmware as tx power, it will revert to
the default tx power for the station.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currenly in delba process calling ath11k_peer_rx_tid_delete() updates
reo with desc invalid and add tid queue to the flush list. If station
send data traffic without addba req and before tid flush, hw gives
those packets as invalid desc reo error. Since we are dropping these
invalid desc packets results in traffic stall.
This patch fix this issue by updating the reo queue with bawindow size 1
instead of tid removal in delba process.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Accessing already stored first msdu data after the skb expand trigger
use_after_free, since first msdu got deleted. so do the descriptor copy
operation before the skb expand operation.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WMI_VDEV_SET_WMM_PARAMS commmand expects the txoplimit param in the units of
32 microseconds. convert the txop unit from 32 microseconds to absolute
microseconds leads to the higher burst values which is incorrect. so no need
to convert the txop unit from 32 microseconds to absolute microseconds.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes sending the pdev id(0,1,2 for mac0, mac1, mac2)
to FW in wmi cmd pktlog enable/disable.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Russell King