The helper function for adding a GPIO chip compiles in a lockdep
key for debugging, the same key is needed for nested chips as
well.
The macro construction is unreadable, replace this with two
static inlines instead.
The _gpiochip_irqchip_add prefixed function is not helpful,
rename it with gpiochip_irqchip_add_key() that tell us what the
function is actually doing.
Fixes: d245b3f9bd ("gpio: simplify adding threaded interrupts")
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when
using threaded interrupts: add a new call
gpiochip_irqchip_add_nested() to indicate that we're dealing
with a nested rather than a chained irqchip, then create a
separate gpiochip_set_nested_irqchip() to mirror
the gpiochip_set_chained_irqchip() call to connect the
parent and child interrupts.
In the nested case gpiochip_set_nested_irqchip() does nothing
more than call irq_set_parent() on each valid child interrupt,
which has little semantic effect in the kernel, but this is
probably still formally correct.
Update all drivers using nested interrupts to use
gpiochip_irqchip_add_nested() so we can now see clearly
which these users are.
The DLN2 driver can drop its specific hack with
.irq_not_threaded as we now recognize whether a chip is
threaded or not from its use of gpiochip_irqchip_add_nested()
signature rather than from inspecting .can_sleep.
We rename the .irq_parent to .irq_chained_parent since this
parent IRQ is only really kept around for the chained
interrupt handlers.
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It should have been @reg_clr instead of @reg_clk
Signed-off-by: Anthony Best <anthonybest@bestanthony.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using GPIO irqchip helpers to setup irqchip for a gpiolib based
driver, it is not possible to select which GPIOs to add to the IRQ domain.
Instead it just adds all GPIOs which is not always desired. For example
there might be GPIOs that for some reason cannot generated normal
interrupts at all.
To support this we add a flag irq_need_valid_mask to struct gpio_chip. When
this flag is set the core allocates irq_valid_mask that holds one bit for
each GPIO the chip has. By default all bits are set but drivers can
manipulate this using set_bit() and clear_bit() accordingly.
Then when gpiochip_irqchip_add() is called, this mask is checked and all
GPIOs with bit is set are added to the IRQ domain created for the GPIO
chip.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most shared headers in include/linux don't need to know what the
internals of a struct module are; all they care about is that it
is a struct and hence they may require a pointer to one.
The advantage in this is that module.h is including a lot of stuff
itself, and an otherwise empty C file that just contains module.h
will result in ~750kB from CPP (compared to say 12kB from init.h)
So we have approximately 50 instances of "struct module;" in the
various include/linux headers already that help us keep module.h
out of other headers; here we do the same for gpio.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO controllers has a special hardware bit we can flip
to support open drain / source. This means that on these hardwares
we do not need to emulate OD/OS by setting the line to input
instead of actively driving it high/low. Add an optional vtable
callback to the driver set_single_ended() so that driver can
implement this in hardware if they have it.
We may need a pinctrl_gpio_set_config() call at some point to
propagate this down to a backing pin control device on systems
with split GPIO/pin control.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device managed APIs devm_gpiochip_add_data() and
devm_gpiochip_remove() for the APIs gpiochip_add_data()
and gpiochip_remove().
This helps in reducing code in error path and sometimes
removal of .remove callback for driver unbind.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
The gpio_chip label is useful for userspace to understand what
kind of GPIO chip it is dealing with. Let's store a copy of this
label in the gpio_device, add it to the struct passed to userspace
for GPIO_GET_CHIPINFO_IOCTL and modify lsgpio to show it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My left hand merges code to privatize the descriptor handling
while my right hand merges drivers that poke around and
disrespect with the same gpiolib internals.
So let's expose the proper APIs for drivers to ask the gpiolib
core if a line is marked as open drain or open source and
get some order around things so this driver compiles again.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We move to manage this pointer under gpiolib control rather than
leave it in the subdevice's gpio_chip. We can not NULL it after
gpiochip_remove so at to keep things tight.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of keeping this reference to the pin ranges in the
client driver-supplied gpio_chip, move it to the internal
gpio_device as the drivers have no need to inspect this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This kind of hacks disturbs the refactoring of the gpiolib.
The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need gpio_device to hold the descriptors so that they can
be lifecycled with the struct gpio_device held from userspace.
Move the descriptor array into gpio_device. Also rename it from
"desc" (singularis) to "descs" (pluralis) to reflect the fact
that it is an array.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpio_device is the struct that survives if the backing
gpio_chip is removed, move the sysfs mock device to this state
container so it becomes part of the dangling state of the
GPIO device on removal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO chips have been around for years, but were never real devices,
instead they were piggy-backing on a parent device (such as a
platform_device or amba_device) but this was always optional.
GPIO chips could also exist without any device at all, with its
struct device *parent (ex *dev) pointer being set to null.
When sysfs was in use, a mock device would be created, with the
optional parent assigned, or just floating orphaned with NULL
as parent.
If sysfs is active, it will use this device as parent.
We now create a gpio_device struct containing a real
struct device and move the subsystem over to using that. The
list of struct gpio_chip:s is augmented to hold struct
gpio_device:s and we find gpio_chips:s by first looking up
the struct gpio_device.
The struct gpio_device is designed to stay around even if the
gpio_chip is removed, so as to satisfy users in userspace
that need a backing data structure to hold the state of the
session initiated with e.g. a character device even if there is
no physical chip anymore.
From this point on, gpiochips are devices.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Board files that define their own bgpio_pdata are broken when
CONFIG_GPIO_GENERIC is disabled and the bgpio_pdata structure
definition is hidden by the #ifdef:
arch/arm/mach-clps711x/board-autcpu12.c:148:15: error: variable 'autcpu12_mmgpio_pdata' has initializer but incomplete type
static struct bgpio_pdata autcpu12_mmgpio_pdata __initdata = {
arch/arm/mach-clps711x/board-autcpu12.c:149:2: error: unknown field 'base' specified in initializer
.base = AUTCPU12_MMGPIO_BASE,
Since the board files should generally not care what drivers are
enabled, this makes the structure definition visible again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0f4630f372 ("gpio: generic: factor into gpio_chip struct")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The separate struct bgpio_chip has been a pain to handle, both
by being confusingly similar in name to struct gpio_chip and
for being contained inside a struct so that struct gpio_chip
is contained in a struct contained in a struct, making several
steps of dereferencing necessary.
Make things simpler: include the fields directly into
<linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and
get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix
some of the member variables with bgpio_* and add proper
kerneldoc while we're at it.
Modify all users to handle the change and use a struct
gpio_chip directly. And while we're at it: replace all
container_of() dereferencing by gpiochip_get_data() and
registering the gpio_chip with gpiochip_add_data().
Cc: arm@kernel.org
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a void * pointer to gpio_chip so that driver can
assign and retrieve some states. This is done to get rid of
container_of() calls for gpio_chips embedded inside state
containers, so we can remove the need to have the gpio_chip
or later (planned) struct gpio_device be dynamically allocated
at registration time, so that its struct device can be properly
reference counted and not bound to its parent device (e.g.
a platform_device) but instead live on after unregistration
if it is opened by e.g. a char device or sysfs.
The data is added with the new function gpiochip_add_data()
and for compatibility we add static inline wrapper function
gpiochip_add() that will call gpiochip_add_data() with
NULL as argument. The latter will be removed once we have
exorcised gpiochip_add() from the kernel.
gpiochip_get_data() is added as a static inline accessor
for drivers to quickly get their data out.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpiochip .get() callback may return a negative error value, it
strictly limits the range of possible non-error returned values to
a subset of [30:0] bitmask, however on practice on success all
gpiochip drivers return either 0 for low signal or 1 for high signal,
this is assured by "gpio: *: Be sure to clamp return value" series of
changes. To avoid any confusion, misinterpretation and potential
errors while developing gpiochip drivers in future convert this
implicit assumption to a mandatory rule.
For output signals with unknown output signal state gpiochip drivers
should return a negative error instead of 0.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide generic request/free implementations that pinctrl aware gpio
drivers can use instead of open coding if they use a 1:1 pin to gpio
signal mapping.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This refactors the changes to the GPIO line naming mechanism to
not have so widespread effects, instead we conclude the patch series
by having created a name attribute in the GPIO descriptor, that need
not be globally unique, and it will be initialized from the old
.names array in struct gpio_chip if it exists, then used in the legacy
sysfs code like the array was used previously.
The associated changes to name lines from the device tree are
controversial and need to stand alone from this. Resulting changes:
1. Remove the export and the header for the gpio_name_to_desc() as so
far the only use is inside gpiolib.c. Staticize gpio_name_to_desc()
and move it above the only function using it.
2. Only print a warning if there are two GPIO lines with the same name.
The reason is to preserve current behaviour: before the previous
changes to the naming mechanism this would not reject probing the
driver, instead the error would occur when trying to export the line
in sysfs, so restore this behaviour, but print a friendly warning
if names collide.
Cc: Johan Hovold <johan@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest gpio hogging mechanism assigns each gpio a 'line-name' in the
devicetree. The 'name' field is different from the 'label' field.
'label' is only used for requested GPIOs to describe its current use by
driver or userspace.
The 'name' field describes the GPIO itself, not the use. This is most
likely identical to the label in the schematic on the GPIO line and
should help to find this particular GPIO.
This is equivalent to the gpiochip->names array. However names should be
stored in the GPIO descriptor. We will use gpiochip->names in the future
only as initializer for the GPIO descriptors for drivers that assign
GPIO names hardcoded. All other GPIO names will be parsed from DT and
directly assigned to the GPIO descriptor.
This patch adds a helper function to find gpio descriptors by name
instead of gpio number.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Since IRQ chip helpers were introduced drivers lose ability to
register separate lockdep classes for each registered GPIO IRQ
chip and the gpiolib now is using shared lockdep class for
all GPIO IRQ chips (gpiochip_irq_lock_class).
As result, lockdep will produce warning when there are min two
stacked GPIO chips and all of them are interrupt controllers.
HW configuration which generates lockdep warning (TI dra7-evm):
[SOC GPIO bankA.gpioX]
<- irq - [pcf875x.gpioY]
<- irq - DevZ.enable_irq_wake(pcf_gpioY_irq);
The issue was reported in [1] and discussed [2].
=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted
---------------------------------------------
sh/63 is trying to acquire lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
but task is already holding lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(class);
lock(class);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by sh/63:
#0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164
#1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0
#2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0
#3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4
#4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398
#5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94
#6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
stack backtrace:
CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14)
[<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c)
[<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20)
[<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128)
[<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c)
[<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94)
[<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc)
[<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54)
[<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc)
[<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4)
[<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124)
[<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398)
[<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4)
[<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728)
[<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4)
[<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8)
[<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0)
[<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8)
[<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164)
[<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c)
[<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54)
Lets fix it by using separate lockdep class for each registered GPIO
IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros.
The implementation of this patch inspired by solution done by Nicolas
Boichat for regmap [3]
[1] http://www.spinics.net/lists/linux-gpio/msg05844.html
[2] http://www.spinics.net/lists/linux-gpio/msg06021.html
[3] http://www.spinics.net/lists/arm-kernel/msg429834.html
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Tested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case we unload and load a driver module again that is registering a
lookup table, without this it will result in multiple entries. Provide
an option to remove the lookup table on driver unload
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all[1] users of the gpiod_get functions are converted to make
use of the up to now optional flags parameter, make it mandatory which
allows to remove some cpp magic.
[1] all but etraxfs-uart which is broken anyhow and I'm allowed to
ignore it by Jesper Nilsson :-)
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull LED subsystem updates from Bryan Wu:
"In this cycle, we finished to merge patches for LED Flash class
driver.
Other than that we have some bug fixes and new drivers for LED
controllers"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (33 commits)
leds:lp55xx: fix firmware loading error
leds: fix max77693-led build errors
leds: fix aat1290 build errors
leds: aat1290: pass flags parameter to devm_gpiod_get
leds: ktd2692: pass flags parameter to devm_gpiod_get
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
leds: aat1290: add support for V4L2 Flash sub-device
DT: aat1290: Document handling external strobe sources
leds: max77693: add support for V4L2 Flash sub-device
media: Add registration helpers for V4L2 flash sub-devices
v4l: async: Add a pointer to of_node to struct v4l2_subdev, match it
Documentation: leds: Add description of v4l2-flash sub-device
leds: add BCM6358 LED driver
leds: add DT binding for BCM6358 LED controller
leds: fix brightness changing when software blinking is active
Documentation: leds-lp5523: describe master fader attributes
leds: lp5523: add master_fader support
leds: leds-gpio: Allow compile test if !GPIOLIB
leds: leds-gpio: Add missing #include <linux/of.h>
gpiolib: Add missing dummies for the unified device properties interface
...
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIOLIB=n:
drivers/leds/leds-gpio.c: In function ‘gpio_leds_create’:
drivers/leds/leds-gpio.c:187: error: implicit declaration of function ‘devm_get_gpiod_from_child’
drivers/leds/leds-gpio.c:187: warning: assignment makes pointer from integer without a cast
Add dummies for fwnode_get_named_gpiod() and devm_get_gpiod_from_child()
for the !GPIOLIB case to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 40b7318319 ("gpio: Support for unified device properties interface")
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Passing a fixed base in struct gpio_chip is done for legacy
systems that cannot handle dynamic allocation. Discourage this
behaviour in the kerneldoc.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up chained handler and handler data if they were set by
gpiochip_set_chained_irqchip().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove gpiod_sysfs_set_active_low (and gpio_sysfs_set_active_low) which
allowed code to change the polarity of a gpio line even after it had
been exported through sysfs.
Drivers should not care, and generally does not know, about gpio-line
polarity which is a hardware feature that needs to be described by
firmware.
It is currently possible to define gpio-line polarity in device-tree and
acpi firmware or using platform data. Userspace can also change the
polarity through sysfs.
Note that drivers using the legacy gpio interface could still use
GPIOF_ACTIVE_LOW to change the polarity before exporting the gpio.
There are no in-kernel users of this interface.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harry Wei <harryxiyou@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@zh-kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean gpio-chip class device registration and deregistration.
The class device is registered when a gpio-chip is added (or from
gpiolib_sysfs_init post-core init call), and deregistered when the chip
is removed.
Store the class device in struct gpio_chip directly rather than do a
class-device lookup on deregistration. This also removes the need for
the exported flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These functions do not belong in <asm-generic/gpio.h> since the
split into separate GPIO headers under <linux/gpio/*>. Move them
to <linux/gpio/driver.h> as is apropriate.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device managed variants of gpiod_get_array() / gpiod_put_array()
functions for conveniently obtaining and disposing of an entire array
of GPIOs with one function call.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions for conveniently obtaining and disposing of
an entire array of GPIOs with one function call.
ACPI parts tested by Mika Westerberg, DT parts tested by Rojhalat
Ibrahim.
Change log:
v5: move the ACPI functions to gpiolib-acpi.c
v4: - use shorter names for members of struct gpio_descs
- rename lut_gpio_count to platform_gpio_count for clarity
- add check for successful memory allocation
- use ERR_CAST()
v3: - rebase on current linux-gpio devel branch
- fix ACPI GPIO counting
- allow for zero-sized arrays
- make the flags argument mandatory for the new functions
- clarify documentation
v2: change interface
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio binding document says that new code should always use named
gpios. Patch 40b73183 added support to parse a list of gpios from child
nodes, but does not make it possible to use named gpios. This patch adds
the con_id property and implements it is done in gpiolib.c, where the
old-style of using unnamed gpios still works.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Right now, in consumer.h, there's some vararg hacks that pass 0 as the
flags. What actually is passed however is GPIOD_ASIS, which naturally is
also 0. Using the define/enum rather then the magic 0 makes it the
define more readable to a passer by.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers need to deal with only firmware representation of its
GPIOs. An example would be a GPIO button array driver where each button
is described as a separate firmware node in device tree. Typically these
child nodes do not have physical representation in the Linux device
model.
In order to help device drivers to handle such firmware child nodes we
add dev[m]_get_named_gpiod_from_child() that takes a child firmware
node pointer as its second argument (the first one is the parent device
itself), finds the GPIO using whatever is the underlying firmware
method, and requests the GPIO properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij