The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the address configured in the device tree is invalid, the
driver will fallback to using a random address from the locally
administered range.
Signed-off-by: Daniel Romell <daro@hms.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new copper device X557.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This shouldn't matter as nothing should be attached still to be
consisted control MDIO speed for these devices as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X557 devices use a different interface to the LED for the port.
This patch reflect that change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add geneve Rx offload support for x550em_a.
The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.
Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().
Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver was only receiving the first 4 bytes of the MAC due
to an incorrect size parameter for ixgbevf_write_msg_read_ack()
in ixgbevf_set_rar_vf().
Correct the size by calculating it on a fly for all instances where
we call ixgbevf_write_msg_read_ack()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adjust a jump target according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-08-19
This series contains updates to i40e and i40evf only.
Jake provides several patches, first just moves a function to co-locate
the two functions related to configuring RSS via the admin queue, which
should help in spotting bugs when comparing the two functions. Fixed
an issue where commit e69ff813af ("i40e: rework the functions to
configure RSS with similar parameters") missed checking whether the seed
is NULL before using it and did not use the passed in *lut parameter.
Fixed an issue where a previous refactor missed i40e_vsi_config_rss()
and the values were being ignored, so checked for the fields and used
them instead of default values. Lastly replaced calls to
create_singlethread_workqueue() with alloc_workqueue() to provide more
control over workqueue creation and allows explicit setting of the
desired mode of operation.
Mitch adds link speed to log messages and reports speed through ethtool.
Carolyn refactors tail bump check and fixes byte ordering problems found
when enabling this feature support. Adds support for HMC resources and
profile commands for x722 firmware.
Heinrich Schuchardt fixes format identifiers from %u to %d since the
variable is defined as an integer.
Catherine fixes an issue where there was a race condition between the
completion of the client open and calls to the client ops, so ensured
that client ops are not called until we are sure client is open.
Harshitha makes sure that i40e_client_release() does not try to use
an adapter pointer which may not be initialized, so make sure it is.
Joe Perches fixes the use of the local macro XSTRINGIFY() to use
__stringify() instead.
Avinash corrects the mutex usage in client_subtask(). Fixed the RDMA
client to open again after reset since it is closed during a PF reset.
Jeff (me) clean up whitespace issues, where indentation was done
inconsistently and with spaces versus tabs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
'Commit 3c8b3efc06 ("vmxnet3: allow variable length transmit data ring
buffer")' changed the size of the buffers in the tx data ring from a
fixed size of 128 bytes to a variable size.
However, while copying data to the data ring, vmxnet3_copy_hdr continues
to carry the old code that assumes fixed buffer size of 128. This patch
fixes it by adding correct offset based on the actual data ring buffer
size.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code uses busy retry when unable to send out receive
completions due to full ring buffer. It also gives up retrying after limit
is reached, and causes receive buffer slots not being recycled.
This patch implements batching of receive completions. It also prevents
dropping receive completions due to full ring buffer.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RAR entry for the SAN MAC address was being cleared when we were
clearing the VMDq pool bits. In order to prevent this we need to add
an extra check to protect the SAN MAC from being cleared.
Fixes: 6e982aeae ("ixgbe: Clear stale pool mappings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDMA client is closed during the PF reset and needs to be opened again.
Setting the flag so that RDMA client is opened in watchdog() function.
Change-ID: I507b1e4cbd05528cdff68fd360ef3dcac8901263
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.
Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Correcting the mutex usage, in client_subtask(), mutex_unlock has
to be called just before client_del_instance() since this function opens
and later closes the same mutex again.
Similarly in client_is_registered removing the mutex since it closes
the mutex twice.
This is a patch suggested by RDMA team.
Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __stringify instead.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_client_release has a print statement that uses an
adapter pointer which is not initialized if a previous if statement
is not true. Hence, intialize it in the right place.
Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were having a race between the completion of the client open and
calls to the client ops so don't call a client op unless we are sure the
client is open.
Testing Hints: Load IWARP driver and make sure it works as expected.
Change-Id: I741f4f2aa4fcbfdad3e40dabbbb1b005856c396b
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i is defined as int but output as %u several times.
Adjust the format identifiers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for HMC resource and profile cmds for X722
firmware.
Change-ID: Icc332101f38ab15d1bfa167823100eb4f6822f7e
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes byte ordering problems found when enabling this feature
support. Without this patch, the feature will not work correctly. This
patch fixes the definitions to have the correct byte order.
Change-ID: Ic7489fbcbe2195df7be62ff5e359201b827cefe6
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver tells us the link speed, so do something with that
information. Add link speed to log messages, and report speed through
ethtool.
Change-Id: I279dc9540cc5203376406050a3e8d67e128d5882
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".
Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pool index has to be converted by get_pool helper to work correctly for
egress pool. In mlxsw the egress pool index starts from 0.
Fixes: 0f433fa0ec ("mlxsw: spectrum_buffers: Implement shared buffer configuration")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware for the qed* adpaters fixes several issues:
- Better blocking of malicious VFs.
- After FLR, Tx-switching [internal routing] of packets might
be incorrect.
- Deletion of unicast MAC filters would sometime have side-effect
of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.
In addition, it would allow driver some new functionality, including:
- Allowing PF/VF driver compaitibility with old drivers [running
pre-8.10.5.0 firmware].
- Better debug facilities.
This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-08-18
This series contains updates to ixgbe and ixgbevf.
Emil cleans up confusing amongst the users by making an error message
into a debug message, since the TXDCTL.ENABLE (and comparable
VFTXDCTL.ENABLE for ixgbevf) bit is set only when the
transmit queue is actually enabled, which may not happen during the
configure phase eve if we waited for it. Converts to using netdev_dbg()
macro instead of our home brewed macro for ixgbevf. Converted the
service task to use atomic bitwise operations when setting and checking
reset requests to reduce the possibility of race conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the drivers into a proper platform device
driver, we can use the device managed helper functions to simplify the
error paths a bit wrt. register resources and IRQs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.
The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv88e6xxx_wait() returns a timeout, something bad has
happened. Make sure it is noticed by logging an error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mv88e6xx_wait() iterated on a counter than a fixed time
interval, it implements the same mechanism as mv88e6xxx_update() uses.
So use it in mv88e6xx_wait().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx driver times out operations on the switch based on
looping until an elapsed wall clock time is reached. However, if
usleep_range() sleeps much longer than expected, it could timeout with
an error without actually checking to see if the devices has completed
the operation. So replace the elapsed time with a fixed upper bound on
the number of loops.
Testing on various switches has shown that switches takes either 0 or
1 iteration, so a maximum of 16 iterations is a safe limit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the redundant "Support for" and "Drivers for" from the Kconfig
short description. This makes the manufacture much more prominent in
the list and makes the shortcut keys useful.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort the files to reduce merge conflicts and to make it easier to find
drivers by name. Also separate the MDIO bus drivers from the PHY
drivers, again to help find what you need.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It added reset function for RoCE driver. RoCE is a feature of hns.
In hip06 SoC, in RoCE reset process, it's needed to configure dsaf
channel reset, port and sl map info. Reset function of RoCE is
located in dsaf module, we only call it in RoCE driver when needed.
This patch is used to fix the conflict, please refer to this link:
https://www.spinics.net/lists/linux-rdma/msg39114.html
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in the switchdev/offloads mode, HW matching is done as
dictated by the offloaded rules and hence we don't need to enable
the ACLs mechanism used by the legacy mode.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding actual offloading support to the new switchdev mode, we didn't
change the setup of the send-to-vport rules to put them in the slow path
table, fix that.
Fixes: 1033665e63 ('net/mlx5: E-Switch, Use two priorities for SRIOV offloads mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mlx5 has also the NONE e-switch mode, we must translate from mlx5
mode to devlink mode on the devlink eswitch mode get call, do that.
While here, remove the mlx5_ prefix from the static function helpers
that deal with the mode to comply with the rest of the code.
Fixes: c930a3ad74 ('net/mlx5e: Add devlink based SRIOV mode change')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid firmware command execution each time the switchdev HW ID attr get
call is made. We do that by reading the ID (PF NIC MAC) only once at
load time and store it on the representor structure.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong key is used when extracting the address type field set by
the flower offload code. We have to use the control key and not the
basic key, fix that.
Fixes: e3a2b7ed01 ('net/mlx5e: Support offload cls_flower with drop action')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set lastuse statistic, when number of packets is changed compared to
last query. This was wrongly dropped when bulk counter reading was added.
Fixes: a351a1b03b ('net/mlx5: Introduce bulk reading of flow counters')
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB
adapters')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PCI error is detected we should save the state of the pci prior to
disabling it.
Also when receiving pci slot reset call we need to verify that the
device is responsive.
Fixes: 89d44f0a6c ('net/mlx5_core: Add pci error handlers to mlx5_core
driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary interface down/up operations upon an MTU change
when it does not affect the rings configuration.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mtu shouldn't be written to hardware on every single interface
open.
Here we set it only when needed, on change_mtu and netdevice creation.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new commmon infrastructure to allocate reosurces dynamically to
Upper layer driver's(ULD) when they register with cxgb4 driver and free
them during unregistering. All the queues and the interrupts for
them will be allocated during ULD probe only and freed during remove.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't really change anything as BGMAC_CHIPCTL_1_IF_TYPE_RMII is
equal to 0. It make code a bit clener, so far when reading it one could
think we forgot to set a proper mode. It also keeps this mode code in
sync with other ones.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can
be found in two packages (versions): BCM53573 and BCM47189. It shares
some code with the Northstar family, but also requires some new quirks.
First of all there can be up to 2 Ethernet cores on this SoC. If that is
the case, they are connected to two different switch ports allowing some
more complex/optimized setups. It seems the second unit doesn't come
fully configured and requires some IRQ quirk.
Other than that only the first core is connected to the PHY. For the
second one we have to register fixed PHY (similarly to the Northstar),
otherwise generic PHY driver would get some invalid info.
This has been successfully tested on Tenda AC9 (BCM47189B0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful to be able to see the hash configuration when running tests.
This patch adds a debugfs node for that purpose.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The division is already being done properly in efx_ef10_get_timer_config
which returns zero-on-success, unlike the old efx_ef10_get_sysclk_freq.
Fixes: d95e329a55 ("sfc: get timer configuration from adapter")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the oops discovered by the Umap2 project and Alan Stern.
The intf member needs to be set before the firmware is downloaded.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was failing on successful registration returning meaningless errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 55954f3bfd ("net: ethernet: bgmac: move BCMA MDIO Phy code into a separate file")
Signed-off-by: David S. Miller <davem@davemloft.net>
At present the code to check in kdump kernel was not disabling
allocation of resources when CONFIG_CHELSIO_T4_DCB is defined, move the
code outside #defines so that it gets disabled irrespective of #define,
when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a write the VFTXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of the home brewed macro make use of netdev_dbg same as
the ixgbe driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use error "rmgr: Cannot insert RX class rule: Operation not supported" is
more meaningful than "rmgr: Cannot insert RX class rule: Unknown error 524"
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to allow for RX network flow classification to insert
and remove ethertype filter by ethtool
Example:
Add an ethertype filter:
$ ethtool -N eth0 flow-type ether proto 0x88F8 action 2
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules
Filter: 15
Flow Type: Raw Ethernet
Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Ethertype: 0x88F8 mask: 0x0
Action: Direct to queue 2
Delete the filter by location:
$ ethtool -N delete 15
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to allow for RX network flow classification to insert
and remove Rx filter by ethtool. Ethtool interface has it's own rules
manager
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 2 rules
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.
Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG. A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.
At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.
While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].
Fixes: 312e06761c ("qede: Utilize xmit_more")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implementing this driver most of the inputs is
provided by Andrew Lunn.
Updating the driver with Andrew Copy right.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the platforms like zynqmp ultrascale+ has a
separate clock gate for the rx clock. Add an optional
rx_clk so that the clock can be enabled.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables
ip -d l
to indicate if trust is on or off for VFs.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shifted the locking around a bit but forgot to delete this unlock so
now it can unlock twice.
Fixes: cd3be169a5 ('i40e: Move the mutex lock in i40e_client_unregister')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.
Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we allocate memory, we must free it. It's simple courtesy.
Change-ID: Id007294096fb53344f1a8b9a0f78eddf9853c5d6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the bug which causes RSS to continue to work
after being disabled. After disabling RSS, traffic would continue
to be assigned to different queues instead of falling back to a
single queue. Without this patch, attempting to disable RSS would
not work as expected. This patch fixes the bug by clearing the
lookup table used by RSS such that all traffic is assigned to a
single queue. This patch also addresses the issue of reinstating
the lookup table should RSS then be re-enabled.
Change-ID: Ib20c7c6a7e9f1f772bb787370f8a8c664796b141
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF goes through reset path during VF creation which happens to also
have notification of VF reset to client. Adding conditional check to
avoid wrongly notifying VF reset during VF creation.
Also changing the call order of VF enable, calling it after VF creation
rather than before.
Change-ID: I96eabd99deae746a2f0fc465194c886f196178ce
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a fix for the bug i.e. unable to create iwarp device
in VF. This is a sync issue and the iwarp device open is called even
before the PCI register writes are done.
Forcing the PCI register writes to happen just before it exits the
function.
Change-ID: I60c6a2c709da89e845f2764cc50ce8b7373c8c44
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a driver is unable to maintain all current user supplied settings
from ethtool (or other sources), it is not ok for a user request to
succeed and silently trample over previous configuration.
To that end, if you change the number of channels, it must not be
allowed to reduce the number of channels (queues) below the current
flow director filter rules targets. In this case, return -EINVAL when
a request to reduce the number of channels would do so. In addition
log a warning to the kernel buffer explaining why we failed, and report
the rules which prevent us from lowering the number of channels.
Change-ID: If41464d63d7aab11cedf09e4f3aa1a69e21ffd88
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where a static analysis tool generates
a warning for "INVARIANT_CONDITION: Expression 'enabled_tc' used
in the condition always yields the same result."
Without this patch, the driver will not pass the static analysis
tool checks without generating warnings.
This patch fixes the problem by eliminating the irrelevant check
and redundant assignment for the value of enabled_tc.
Change-ID: Ia7d44cb050f507df7de333e96369d322e08bf408
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function calls netif_set_real_num_(tx|rx)_queues, both of which
should be done only under rntl lock. Unfortunately the
i40evf_init_task did not hold the rtnl_lock as necessary. This patch
adds the locking needed.
Change-ID: Ib72a21c3ce22b71a226b16f9bbe0f5f8cc3e849b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we are resetting the pf stats we should also reset the RX csum
error stat.
Change-ID: I7af5ee0ec81a10f6deee1a7b8c2082ea068ef620
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we do a reset, all the VLAN filters get added again. Therefore we also
want to reset the VLAN count to 0 or we quickly run out of filters.
Change-ID: I459f26851e22204dc8b8999928ad87cde8170119
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The client->open call in this path was not protected with the
client instance mutex, and hence the client->close can get initiated
before the open completes.
Change-Id: I0ed60c38868dd3f44966b6ed49a063d0e5b7edf5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add sniffer TX and RX namespaces to receive ingoing and outgoing
traffic.
Each outgoing/incoming packet is duplicated and steered to the sniffer
TX/RX namespace in addition to the regular flow.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When mlx5_ib is loaded, we would like each card's IB devices
to be added according to its LAG state (one IB device, instead of
two, is to be added if LAG is active).
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add interfaces for issuing CREATE_VPORT_LAG and
DESTROY_VPORT_LAG commands.
Used for receiving PF1's eth traffic on PF0's
root ft.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
This namespace is used for LAG demux flowtable.
The idea is to position the LAG demux ft between
bypass and kernel flowtables, allowing raw-eth
traffic from both ports to be received by the PF0
IB device.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add interfaces to allow the creation and destruction of a
LAG demux flow table.
It is a special flow table used during LAG for redirecting
non user-mode packets from PF0 to PF1 root ft, if a packet was
received on phys port two.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Until support will be added for RoCE LAG SRIOV.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
TISes belonging to the mlx5e NIC should not be
subject to port remap.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Used by IB driver for determining the IB bond
device's netdev, when LAG is active.
Returns PF0's netdev if mode is not active-backup,
or the PF netdev of the active slave when mode is
active-backup.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Available on dual port cards only, this feature keeps
track, using netdev LAG events, of the bonding
and link status of each port's PF netdev.
When both of the card's PF netdevs are enslaved to the
same bond/team master, and only them, LAG state
is active.
During LAG, only one IB device is present for both ports.
In addition to the above, this commit includes FW commands
used for managing the LAG, new facilities for adding and removing
a single device by interface, and port remap functionality according to
bond events.
Please note that this feature is currently used only for mimicking
Ethernet bonding for RoCE - netdevs functionality is not altered,
and their bonding continues to be managed solely by bond/team driver.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Exposed LAG commands enum and layouts:
- CREATE_LAG
HW enters LAG mode:
RoCE traffic from port two is received on PF0 core dev.
Allows to set tx_affinity (tx port) for QPs and TISes.
Allows to port remap QPs and TISes, overriding their
tx_affinity behavior.
- MODIFY_LAG
Remap QPs and TISes to another port.
- QUERY_LAG
Query whether LAG mode is active.
- DESTROY_LAG
HW exits LAG mode, returning to non-LAG behavior.
- CREATE_VPORT_LAG
Merge Ethernet flow steering, such that traffic received on port
two jumps to PF0 root flow table.
Available only in LAG mode.
- DESTROY_VPORT_LAG
Ethernet flow steering returns to non-LAG behavior.
Caps added:
- lag_master
Driver is in charge of managing the LAG.
This is currently the only option.
- num_lag_ports
LAG is supported only if this field's value is 2.
Other fields:
- QP/TIS tx port affinity
During LAG, this field controls on which port a QP or TIS resides.
- TIS strict tx affinity
When this field is set, the TIS will not be subject to port remap by
CREATE_LAG/MODIFY_LAG.
- LAG demux flow table
Flow table used for redirecting non user-space traffic back to
PF1 root flow table, if the packet was received on port two.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Replaced mlx5_query_port_proto_oper with separate functions per link
type. The functions should take different arguments so no point in
trying to unite them.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The mlx5e_link_mode enumeration will also be used in mlx5_ib for RoCE.
This patch moves the enumeration to the mlx5 driver port header file.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Use mlx5 ifc MODIFY_BITMASK_VSD in mlx5e_modify_rq_vsd and expose counter
set capability bit in hca caps structure.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-08-16
This series contains fixes to e1000e, igb, ixgbe and i40e.
Kshitiz Gupta provides a fix for igb to resolve the PHY delay compensation
math in several functions.
Jarod Wilson provides a fix for e1000e which had to broken up into 2
patches, first is prepares the driver for expanding the list of NICs
that have occasional ~10 hour clock jumps when being used for PTP.
Second patch actually fixes i218 silicon which has been experiencing
the clock jumps while using PTP.
Alex provides 2 patches for ixgbe now that he is back at Intel. First
fixes setting VLNCTRL.VFE bit, which was left unchanged in earlier patches
which resulted in disabling VLAN filtering for all the VFs. Second
corrects the support for disabling the VLAN tag filtering via the
feature bit.
Lastly, David fixes i40e which was causing a kernel panic when
non-contiguous traffic classes or traffic classes not starting with TC0,
were configured on a link partner switch. To fix this, changed the
logic when determining the total number of TCs enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets enter the device they are classified to a priority group
(PG) buffer based on their PCP value. After their egress port and
traffic class are determined they are moved to the switch's shared
buffer and await transmission, if:
(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)
Packets scheduled to transmission through CPU port (trapped to CPU) use
traffic class 7, which has a zero maximum and minimum quotas. However,
when such packets arrive from PG 0 they are admitted to the shared
buffer as PG 0 has a non-zero minimum quota.
Allow all packets to be trapped to the CPU - regardless of the PG they
were classified to - by assigning a 10KB minimum quota for CPU port and
TC7.
Fixes: 8e8dfe9fdf ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralue pack function needs to set op, otherwise it is 0 for add always.
Fixes: d5a1c749d2 ("mlxsw: reg: Add Router Algorithmic LPM Unicast Entry Register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Reported-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following traps:
1) MTU Error: Trap packets whose size is bigger than the egress RIF's
MTU. If DF bit isn't set, traffic will continue to be routed in slow
path.
2) TTL Error: Trap packets whose TTL expired. This allows traceroute to
work properly.
3) OSPF packets.
Fixes: 7b27ce7bb9 ("mlxsw: spectrum: Add traps needed for router implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of init sequence")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement low-level commands to support vxlan encapsulation.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Implement the low-level part of the PF side in setting minimum
inline header mode for VFs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove duplicate pci dev name printing in mlx5_core_err.
Use mlx5_core_{warn,info,err} where possible to have the pci info in the
driver log messages.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Parvi Kaustubhi <parvik@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Now as all commands use mlx5 ifc interface, instead of doing two calls
for executing a command we embed command status checking into
mlx5_cmd_exec to simplify the interface.
Also we do here some cleanup for redundant software structures
(inbox/outbox) and functions and improved command failure output.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Prior to this patch we assumed that modify QP commands have the
same layout.
In ConnectX-4 for each QP transition there is a specific command
and their layout can vary.
e.g: 2err/2rst commands don't have QP context in their layout and before
this patch we posted the QP context in those commands.
Fortunately the FW only checks the suffix of the commands and executes
them, while ignoring all invalid data sent after the valid command
layout.
This patch removes mlx5_modify_qp_mbox_in and changes
mlx5_core_qp_modify to receive the required transition and QP context
with opt_param_mask if needed. This way the caller is not required to
provide the command inbox layout and it will be generated automatically.
mlx5_core_qp_modify will generate the command inbox/outbox layouts
according to the requested transition and will fill the requested
parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created QP/XRCD commands layout
amd use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.
To fix this, the patch changes the logic when determining
the total number of TCs enabled. Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled. Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous. If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 1636956491 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is prepatory work for an expanding list of adapter families that have
occasional ~10 hour clock jumps when being used for PTP. Factor out the
sanitization function and convert to using a feature (bug) flag, per
suggestion from Jesse Brandeburg.
Littering functional code with device-specific checks is much messier than
simply checking a flag, and having device-specific init set flags as needed.
There are probably a number of other cases in the e1000e code that
could/should be converted similarly.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com>
Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency)
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Runtime warning occurs if DMA-API debug feature is enabled that would be
raised by pointers passed to DMA API as arguments to inconsistent struct
device objects, so that the patch makes them usage aligned between DMA
operations such as dma_map_*() and dma_unmap_*() to eliminate the warning.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08ef55c6f2
("net-next: mediatek: fix gigabit and flow control advertisement")
had supported proper flow control settings for GMAC1. But for GMAC0,
1.GMAC0 shares the common logic with GMAC1 inside mtk_phy_link_adjust()
to adapt various settings for the target phy.
2.GMAC0 uses fixed-phy to connect to a builtin gigabit switch with
fixed link speed as commit 0c72c50f6f
("net-next: mediatek: add fixed-phy support") describes.
3.However, fixed-phy doesn't enable SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flag on default that would cause mtk_phy_link_adjust() not to
enable flow control setting on GMAC0 properly and cause packet dropped
when high traffic.
Due to these reasons, the patch adds SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flags on fixed-phy used by the driver to have proper handling on
the both GMAC with the shared common logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes up the incorrect setup of reduced MII (RMII) on GMAC
and adds the supplement for the setup of reverse MII (REVMII) on GMAC
, and rearranges the error handling for invalid PHY argument.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces every MDIO direct or indirect access with the new
generic mv88e6xxx_phy_* routines.
This allows us to get rid of the mv88e6xxx_mdio_{read,write}_{,in}direct
and {_,}mv88e6xxx_mdio_page_{read,write} functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mv88e6xxx_phy_page_{read,write} routines and use them to access the
SerDes PHY device registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old chips use a direct access to the PHY devices registers. Next chips
have a PHY Polling Unit (PPU) which needs to be disabled before
accessing PHY registers. Newer chips have an indirect access to the PHY
devices so that disabling the PPU is not necessary.
Introduce a new phy_ops structure in the chip to describe the required
PHY access routines.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe the presence of the Global2 SMI PHY registers, used to
indirectly access the internal SMI devices registers on some chips.
Also temporarily forward declare mv88e6xxx_g2_smi_phy_{read,write} to
use them in mv88e6xxx_mdio_{read,write}_indirect, before getting rid of
the later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of SMI Command and Data registers
used to indirectly access internal SMI devices registers when the switch
SMI address is not zero.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no locked version of the wait routine anymore, rename
the _ prefixed version and make it use the new read API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the invalid dma width
error handling case instead of 0.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding driver sets IFF_BONDING on both master (the bonding device) and
slave (the real NIC) devices and in netvsc_netdev_event() we want to skip
master devices only. Currently, there is an uncertainty when a slave
interface is removed: if bonding module comes first in netdev_chain it
clears IFF_BONDING flag on the netdev and netvsc_netdev_event() correctly
handles NETDEV_UNREGISTER event, but in case netvsc comes first on the
chain it sees the device with IFF_BONDING still attached and skips it. As
we still hold vf_netdev pointer to the device we crash on the next inject.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're not guaranteed to see NETDEV_REGISTER/NETDEV_UNREGISTER notifications
only once per VF but we increase/decrease module refcount unconditionally.
Check vf_netdev to make sure we don't take/release it twice. We presume
that only one VF per netvsc device may exist.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We reset vf_inject on VF going down (netvsc_vf_down()) but we don't on
VF removal (netvsc_unregister_vf()) so vf_inject stays 'true' while
vf_netdev is already NULL and we're trying to inject packets into NULL
net device in netvsc_recv_callback() causing kernel to crash.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a deadlock scenario:
- netvsc_vf_up() schedules netvsc_notify_peers() work and quits.
- netvsc_vf_down() runs before netvsc_notify_peers() gets executed. As it
is being executed from netdev notifier chain we hold rtnl lock when we
get here.
- we enter while (atomic_read(&net_device_ctx->vf_use_cnt) != 0) loop and
wait till netvsc_notify_peers() drops vf_use_cnt.
- netvsc_notify_peers() starts on some other CPU but netdev_notify_peers()
will hang on rtnl_lock().
- deadlock!
Instead of introducing additional synchronization I suggest we drop
gwrk.dwrk completely and call NETDEV_NOTIFY_PEERS directly. As we're
acting under rtnl lock this is legitimate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct netvsc_device is not suitable for storing VF information as this
structure is being destroyed on MTU change / set channel operation (see
rndis_filter_device_remove()). Move all VF related stuff to struct
net_device_context which is persistent.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The null check on mdio->irq is redundant since mdio->irq is an array
of PHY_MAX_ADDR ints and hence can never be null. Remove the redundant
check.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch touches various prints in the driver - it reduces the
verbosity of some prints [which were previously logged by default]
while adding several new debug prints and modifying others.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change qed* code in trivial manner; This isn't necessarily
semantic-only, but the end result is the same, i.e., no change
should occur from user perspective. Changes include:
- Using temporary variables to better fit 80-character restrictions.
- Removal of unused variables & code with no effect.
[plus some additional minor modifications].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make semantic-only adjustments to qed* drivers, such as:
- Changes in code indentation.
- Usage of BIT() macro.
- re-naming of variables.
- Re-ordering of variable declerations.
- Removal of (== 0) and (!= 0) in conditions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use struct gre_base_hdr directly in pptp_gre_header instead of
duplicated members;
2. Use existing macros like GRE_KEY, GRE_SEQ, and so on instead of
duplicated macros defined by PPTP;
3. Add new macros like GRE_IS_ACK/SEQ and so on instead of
PPTP_GRE_IS_A/S and so on;
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlxsw_sp_router_fib4_add_info_destroy(), the fib_entry pointer is used
after it has been freed by mlxsw_sp_fib_entry_destroy(). Use a temporary
variable to fix this.
Fixes: 61c503f976 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner and .bus fields since module_spi_driver() is used
which set them automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function macb_probe()
in the platform_get_irq() error handling case.
Fixes: c69618b3e4 ("net/macb: fix probe sequence to setup clocks earlier")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'dcbx_info is malloced in qed_dcbnl_get_ieee_pfc() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: a1d8d8a51e ("qed: Add dcbnl support.")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_vf_mac support which allows to set the MAC address
for cxgb4vf interfaces from the host
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue:
For instance, the current APIs assume a 1-to-1 mapping of Network Ports,
Physical Functions and the SR-IOV Virtual Functions of those Physical
Functions. This is not the case with our cards where any Virtual
Function can be hooked up to any Port -- or any number of Ports the
current Linux APIs also assume only 1 Network Interface/Port can be
accessed per Virtual Function.
Another issue is that these APIs assume that the Administrative Driver
is attached to the Physical Function Associated with a Virtual Function.
This is not the case with our card where all administration is performed
by a Driver which is not attached to any of the Physical Functions which
have SR-IOV PCI Capabilities.
Another consequence of these assumptions is the inability to utilize all
of the cards SR-IOV resources. For instance, our cards have SR-IOV
Capabilities on Physical Functions 0..3 and the administrative Driver
attaches to Physical Function 4. Each of the Physical Functions 0..3 can
support up to 16 Virtual Functions. With the current Linux APIs, a
2-Port card would only be able to use the Virtual Functions on Physical
Function 0..1 and not allow the Virtual Functions on Physical Functions
2..3 to be used since there are no Ports 2..3 on a 2-Port card.
Fix:
Since the control node is always the netdevice for all VF ACL commands.
Created a dummy netdevice for each Physical Function from 0 to 3 through
which one could control their VFs. The device won't be associated with
any port, since it doesn't need to transmit/receive. Its purely used
for VF management purpose only. The device will be registered only when
VF for a particular PF is configured using PCI sysfs interface and
unregistered while pci_disable_sriov() for the PF is called.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove old representation of manually created MKey/PSV commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created CQ commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created EQ commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created Pages management
commands layout, and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created MCG commands layout
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created PD/UAR commands layouts
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created ACCESS_REG/MAD_IFC
commands layout and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created Init/Teardown hca
commands layout and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
In the case where phydev->interrupts is not PHY_INTERRUPT_ENABLED
function vsc85xx_ack_interrupt is returning an uninitialized
garbage value. Fix this by initializing rc to zero.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea for type_check in dev_get_nest_level() was to count the number
of nested devices of the same type (currently, only macvlan or vlan
devices).
This prevented the false positive lockdep warning on configurations such
as:
eth0 <--- macvlan0 <--- vlan0 <--- macvlan1
However, this doesn't prevent a warning on a configuration such as:
eth0 <--- macvlan0 <--- vlan0
eth1 <--- vlan1 <--- macvlan1
In this case, all the locks end up with a nesting subclass of 1, so
lockdep thinks that there is still a deadlock:
- in the first case we have (macvlan_netdev_addr_lock_key, 1) and then
take (vlan_netdev_xmit_lock_key, 1)
- in the second case, we have (vlan_netdev_xmit_lock_key, 1) and then
take (macvlan_netdev_addr_lock_key, 1)
By removing the linktype check in dev_get_nest_level() and always
incrementing the nesting depth, lockdep considers this configuration
valid.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, trying to setup a vlan over a macsec device, or other
combinations of devices, triggers a lockdep warning.
Use netdev_lockdep_set_classes and ndo_get_lock_subclass, similar to
what macvlan does.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch respell some word badly spelled.
- Invidate instead of Invalidate
- proble instead of probe
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing of_node_put() after finishing the usage
of of_parse_phandle() or of_node_get() used by fixed_phy.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix runtime warning with lockdep is enabled due that u64_stats_sync
is not initialized well, so add it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of leftover symbol conflicts caused by hashtable.h
being included by netdevice.h; those were not caught as build failure
(they're "only" a warning, but in fact real bugs). Fix those up.
Fixes: e87a8f24c ("net: resolve symbol conflicts with generic hashtable.h")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting BGXX_SPUX_MISC_CONTROL::RX_PACKET_DIS is not needed as
packet reception is anyway disabled by BGXX_CMRX_CONFIG::DATA_PKT_RX_EN.
Also setting RX_PACKET_DIS causes a bogus remote fault condition
which delays link detection.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard API to generate a random RSS hash key
on every boot.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables parsing of inner layers for tunnelled packets.
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables bulk freeing on the Tx side.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set MAC addresses only for primary VF's and don't for
secondary VFs.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SQ/TXQ is reclaimed i.e reset it's stats also automatically reset
by HW. This is not the case with RQ. Also VF doesn't have write access
to statistics counter registers. Hence a new Mbox msg is introduced which
supports resetting RQ, SQ and full Qset stats. Currently only RQ stats
are being reset using this mbox message.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding debug messages in case of NACK for a mailbox message, also
did small cleanups.
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of a round about way of converting buffers to SKBs and
combining them into a frag list, use standard skb_add_rx_frag()
API to merge page fragments. This code is useful when incoming
packets are of size more than RCV_FRAG_LEN which is currently
set to 2048bytes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the way VF's irqs are visible in /proc/interrupts.
Instead of VF id, logical interface's netdev name is used for IRQ
naming and also all secondary VF's interrupts in multiqset config
use primary VF's netdev name.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx has 4 BGX blocks and are enabled mixed QLM/DLM
configs. BGX0/BGX1 are from QLM2/QLM3, BGX3 is DLM4
and BGX2 is split across DLM5 & DLM6.
This patch adds support for BGX2's split config and also
enables all 4 BGXs to be used.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx will have 4 BGX blocks i.e 16 LMACs, to avoid changing
the same with every platform, nicpf struct elements which
track LMAC related info are now allocated runtime based
on platform's max possible BGX count.
Also fixed configuring min packet size for all LMAC's
supported on a platform.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RGX/RGMII interface type support to BGX
driver. This type of interface is supported by 81xx SOC.
CN81XX VNIC has 8 VFs and max possible LMAC interfaces are 9,
hence RGMII interface will not work if all DLMs are in BGX mode
and all 8 LMACs are enabled
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for QSGMII interface type to
the BGX driver. This type of interface is supported by
81xx SOC.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for BGX module on 81xx where a BGX
can be split and have different LMACs configured in
different modes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 88xx all LMACs in a BGX will be in same mode but on 81xx
BGX can be split as two and there can be LMACs configured in
different modes.
These changes move lmac_type, lane2serdes fields into per lmac
struct from BGX struct. Got rid of qlm_mode field which has become
redundant with these changes. And now no of valid LMACs is read
from CSRs configured by low level firmware and figuring out the
same based on QLM mode is discarded
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
88xx has 128 VFs, 81xx has 8 VFs and 83xx will have 32VFs.
Made changes to PF driver such that mailbox interrupt enable
registers are configuired based on number of VFs HW supports.
Also cleanedup mailbox irq handler registration code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike 88xx, CQE_RX descriptor's tunnelling extension i.e CQE_RX2_S
is always enabled on 81xx/83xx and HW does insert these fields into
CQE_RX. As a result receive buffer addresses will now be present at
7th word of CQE_RX instead of 6th.
Enable CQE_RX2_S on 88xx pass 2.x as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
81xx has only 4 CPUs, so it doesn't make sense to initialize
entire Qset i.e 8 queues by default. Made changes to queue
initialization to init queues equal to number of CPUs or
8 queues whichever is lesser. Also this will be applicable to
VMs with VNIC VF attached and having less VCPUs
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds info on HW maximums of 81xx/83xx and also
configures receive and transmit datapaths accordingly.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device IDs of VNIC on newer chips and also
registers VF driver with them. Device id remains same for all
versions of chips but subsystem device id changes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver has most of the HW maximums info like no of channels,
traffic limiters, RSS indices e.t.c in the form of macros. These have
been moved into a 'hw_info' structure so that support for VNIC on
newer chips with different set of HW maximums can be added.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the backward compatibility on handling phy_connect(), by
iterating over the phy-handle, when new DT is used with older kernel.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 10GbE SFP+ module is not plugged in or cable is not connected,
the link status register does not report the proper state due
to floating signal. This patch checks the module present status via an
GPIO to determine whether to ignore the link status register and report
link down.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the link recovery issue, by doing PCS reset
when the link is down.
Signed-off-by: Fushen Chen <fchen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rearranges the port initialization sequence as recommended by
hardware specification. This patch also removes, mac_init() call from
xgene_enet_link_state(), as it was not required.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes FPSel and NxtFPSel fields length to 5-bit value.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since register_netdev() call in xgene_enet_probe() was moved down to
the end, it doesn't properly handle errors that may occur, by
deconstructing everything that was setup before the error occurred.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgene_enet_init_hw() should delete any descriptor rings and
buffer pools setup should le_ops->cle_init() return an error.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to xgene_enet_delete_bufpool() freeing skbs, their associated
dma memory should also be unmapped.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed compiler warnings reported with -Wmaybe-uninitialized W=1,
/drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_rx_frame’:
../drivers/net/ethernet/apm/xgene/xgene_enet_main.c:455:27: warning: variable ‘pdata’ set but not used [-Wunused-but-set-variable]
struct xgene_enet_pdata *pdata;
^
../drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_remove’:
../drivers/net/ethernet/apm/xgene/xgene_enet_main.c:1691:30: warning: variable ‘mac_ops’ set but not used [-Wunused-but-set-variable]
const struct xgene_mac_ops *mac_ops;
^
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SFN8000 series adapters the MC provides a method to get the timer
quantum and the maximum timer setting. We revert to the old values if the
new call is unavailable.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFN8000-series NICs require a new method of setting interrupt moderation,
via MCDI. This is indicated by a workaround flag. This new MCDI command
takes an explicit time value rather than a number of ticks. It therefore
makes sense to also store the moderation values in terms of time, since
that is what the ethtool interface is interested in.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than explicitly specifying flags we can now specify a desired
performance target to the firmware, ie higher throughput or lower latency.
For now we use the default "auto" configuration.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these critical sections protected by page_lock are all entered
from the user context or bottom half context, they can be replaced
with the spin_lock() or spin_lock_bh instead of spin_lock_irqsave().
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_DSA_HWMON is disabled, we get warnings about two unused
functions whose only callers are all inside of an #ifdef:
drivers/net/dsa/mv88e6xxx.c:3257:12: 'mv88e6xxx_mdio_page_write' defined but not used [-Werror=unused-function]
drivers/net/dsa/mv88e6xxx.c:3244:12: 'mv88e6xxx_mdio_page_read' defined but not used [-Werror=unused-function]
This adds another ifdef around the function definitions. The warnings
appeared after the functions were marked 'static', but the problem
was already there before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 57d3231057 ("net: dsa: mv88e6xxx: fix style issues")
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a driver for the ENA family of networking devices.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for gmiitorgmii converter.
The GMII to RGMII IP core provides the Reduced Gigabit Media
Independent Interface (RGMII) between Ethernet physical media
Devices and the Gigabit Ethernet controller. This core can
Switch dynamically between the three different speed modes of
Operation by configuring the converter register through mdio write.
MDIO interface is used to set operating speed of Ethernet MAC.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macsec_notify() loops over the list of macsec devices configured on the
underlying device when this device is being removed. This list is part
of the rx_handler data.
However, macsec_dellink unregisters the rx_handler and frees the
rx_handler data when the last macsec device is removed from the
underlying device.
Add macsec_common_dellink() to delete macsec devices without
unregistering the rx_handler and freeing the associated data.
Fixes: 960d5848db ("macsec: fix memory leaks around rx_handler (un)registration")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've clean skb_array in macvtap_put_queue() but still try to pop from
it during macvtap_sock_destruct(). Fix this use after free by moving
the skb array cleanup to macvtap_sock_destruct() instead.
Fixes: 362899b872 ("macvtap: switch to use skb array")
Reported-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 64 bit addressing and BDs.
-> Enable 64 bit addressing in DMACFG register.
-> Set DMA mask when design config register shows support for 64 bit addr.
-> Add new BD words for higher address when 64 bit DMA support is present.
-> Add and update TBQPH and RBQPH for MSB of BD pointers.
-> Change extraction and updation of buffer addresses to use
64 bit address.
-> In gem_rx extract address in one place insted of two and use a
separate flag for RXUSED.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.
Please consider applying this to 'net-next' branch.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale, cpts, version, rx_packet_max, bus_freq, interrupt pacing
parameters are common per net device that uses the same h/w. So,
move them to common driver structure.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi structs are common for both net devices in dual_emac
mode, In order to not hold duplicate links to them, move to
cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These data are common for net devs in dual_emac mode. No need to hold
it for every priv instance, so move them under cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irq data are common for net devs in dual_emac mode. So no need to
hold these data in every priv struct, move them under cpsw_common.
Also delete irq_num var, as after optimization it's not needed.
Correct number of irqs to 2, as anyway, driver is using only 2,
at least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every net device private struct holds links to shared cpdma resources.
No need to save and every time synchronize these resources per net dev.
So, move it to common driver struct.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King