Resending patch considering Grants G's code review.
Main goal to submit this patch is code cleaup.
1. Better driver debug prints and code indentation.
2. fault_reset_work_lock is not used anywhere. driver is using taskmgmt_lock
instead of fault_reset_work_lock.
3. setting pci_set_drvdata properly.
4. Ingore config request when IOC is in reset state.( ioc_reset_in_progress
is set).
5. Init/clear managment frame proprely.(INITIALIZE_MGMT_STATUS and
CLEAR_MGMT_STATUS)
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) SAS topology Rescan is added. If Firmware is doing Reset and we get
Device add interrupt from Firmware, we will not receive it as part of Reset
is going ON. After Reset we will do special Rescan of SAS topology.
2.) Driver version changed from 3.04.08 to 3.04.09.
Added proper lock/unlock in mptsas_not_responding_devices() as per James'
comment.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SAS topology scan is restructured. HBA firmware is generating more
events. Expander Events are added, Link status events are also added with
respect to SAS topology scan optimization.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now Firmware events are handled by firmware event queue.
Previously it was handled in interrupt context/WorkQueue of Linux.
Firmware Event handling is restructured and optimized.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) rewrite of ioctl_cmds internal generated function that issue commands to
firmware, porting them to be single threaded using the generic MPT_MGMT
struct. All wait Queues are replace by completion Queue.
2) added seperate callback handler for ioctl task managment
(mptctl_taskmgmt_reply), to handle command that timeout
3) rewrite mptctl_bus_reset
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) Added taskmgmt_quiesce_io flag in IOC and removed resetPending from
_MPT_SCSI_HOST struct.
2.) Reset from Scsi mid layer and internal Reset are seperate context.
Adding DeviceResetCtx for internal Device reset frame.
mptsas_taskmgmt_complete is optimized as part of implementation.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1.) rewrite taskmanagement request and completion routines, making them
single threaded and using the generic MPT_MGMT struct, deleting
mptscsih_TMHandler, replacing with single request TM handler
mptscsih_IssueTaskMgmt, and killing the watchdog timer functions.
2.) cleanup ioc_reset callback handlers, introducing wrappers for
synchronizing error recovery (mpt_set_taskmgmt_in_progress_flag,
mpt_clear_taskmgmt_in_progress_flag), as the fusion firmware only handles
one task management request at a time
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Rewrite of all internal generated functions that issue commands to firmware,
porting them to be single threaded using the generic MPT_MGMT
struct. Implemented using completion Queue.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
1) Previously we had mutliple #defines to use same values.
Now those #defines are optimized.
MPT_IOCTL_STATUS_* is removed and MPT_MGMT_STATUS_* are new
#defines.
2.) config path is optimized.
Instead of wait Queue and timer, using completion Q.
3.) mpt_timer_expired is not used.
[jejb: elide patch to eliminate mpt_timer_expired]
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SendEventNotification was handled through FIFO, now it is using doorbell to
communicate with hardware. Added Sleep Flag as an extra argument to support
Can-Sleep feature. Resending patch including compilation error fix reviewed
by Grant Grundler.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sas_discovery_quiesce_io flag is used to control IO start/resume functionality.
IO will be stoped while doing discovery of topology. Once discovery is completed
It will resume IO. Resending patch including James review.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The reason for this change is there is a data corruption when four different
physical memory regions in the 36GB to 37GB region are
accessed. This is only affecting 1078.
The solution is we need to use different addressing when filling in
the scatter gather table for the effected memory regions. So instead
of snooping on all four different memory holes, we treat any physical
addresses in the 36GB address with the same algorithm.
The fix is explained below
1) Ensure that the message frames are NOT located in the trouble
region. There is no remapping available for message frames, they must
be allocated outside the problem region.
2) Ensure that Sense buffers are NOT in the trouble region. There is
no remapping available.
3) Walk through the SGE entries and if any are inside the trouble region
then they need to be remapped as discussed below.
1) Set the Local Address bit in the SGE Flags field.
MPI_SGE_FLAGS_LOCAL_ADDRESS
2) Ensure we are using 64-bit SGEs
3) Set MSb (Bit 63) of the 64-bit address, this will indicate buffer
location is Host Memory.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
plat-omap/mailbox, floppy, viocd, mspro_block, i2o_block and
mmc/card/queue are already pretty close to dequeueing model and can be
converted with simple changes. Convert them.
While at it,
* xen-blkfront: !fs check moved downwards to share dequeue call with
normal path.
* mspro_block: __blk_end_request(..., blk_rq_cur_byte()) converted to
__blk_end_request_cur()
* mmc/card/queue: loop of __blk_end_request() converted to
__blk_end_request_all()
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With the previous changes, the followings are now guaranteed for all
requests in any valid state.
* blk_rq_sectors() == blk_rq_bytes() >> 9
* blk_rq_cur_sectors() == blk_rq_cur_bytes() >> 9
Clean up accessor usages. Notable changes are
* nbd,i2o_block: end_all used instead of explicit byte count
* scsi_lib: unnecessary conditional on request type removed
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement accessors - blk_rq_pos(), blk_rq_sectors() and
blk_rq_cur_sectors() which return rq->hard_sector, rq->hard_nr_sectors
and rq->hard_cur_sectors respectively and convert direct references of
the said fields to the accessors.
This is in preparation of request data length handling cleanup.
Geert : suggested adding const to struct request * parameter to accessors
Sergei : spotted error in patch description
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Ackec-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
end_request() has been kept around for backward compatibility;
however, it's about time for it to go away.
* There aren't too many users left.
* Its use of @updtodate is pretty confusing.
* In some cases, newer code ends up using mixture of end_request() and
[__]blk_end_request[_all](), which is way too confusing.
So, add [__]blk_end_request_cur() and replace end_request() with it.
Most conversions are straightforward. Noteworthy ones are...
* paride/pcd: next_request() updated to take 0/-errno instead of 1/0.
* paride/pf: pf_end_request() and next_request() updated to take
0/-errno instead of 1/0.
* xd: xd_readwrite() updated to return 0/-errno instead of 1/0.
* mtd/mtd_blkdevs: blktrans_discard_request() updated to return
0/-errno instead of 1/0. Unnecessary local variable res
initialization removed from mtd_blktrans_thread().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Joerg Dorchain <joerg@dorchain.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Laurent Vivier <Laurent@lvivier.info>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: unsik Kim <donari75@gmail.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Impact: fix bug
the third param in module_param(,,) is perm instead of default value.
we still need to assign default at first. Also, the default is now
zero not one, so fix the parameter text to reflect that.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for MSI enable/disable for different buses FC,SPI,SAS
instead of having single MSI enable/disable feature.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This Patch is submitted to increment the MPI headers used by LSI MPT
fusion drivers to the latest version 01.05.19. Year is changed in
CopyRight.
Signed-off-by: Kashyap Desai <kadesai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k1.
[SCSI] qla2xxx: Add ISP81XX support.
[SCSI] qla2xxx: Use proper request/response queues with MQ instantiations.
[SCSI] qla2xxx: Correct MQ-chain information retrieval during a firmware dump.
[SCSI] qla2xxx: Collapse EFT/FCE copy procedures during a firmware dump.
[SCSI] qla2xxx: Don't pollute kernel logs with ZIO/RIO status messages.
[SCSI] qla2xxx: Don't fallback to interrupt-polling during re-initialization with MSI-X enabled.
[SCSI] qla2xxx: Remove support for reading/writing HW-event-log.
[SCSI] cxgb3i: add missing include
[SCSI] scsi_lib: fix DID_RESET status problems
[SCSI] fc transport: restore missing dev_loss_tmo callback to LLDD
[SCSI] aha152x_cs: Fix regression that keeps driver from using shared interrupts
[SCSI] sd: Correctly handle 6-byte commands with DIX
[SCSI] sd: DIF: Fix tagging on platforms with signed char
[SCSI] sd: DIF: Show app tag on error
[SCSI] Fix error handling for DIF/DIX
[SCSI] scsi_lib: don't decrement busy counters when inserting commands
[SCSI] libsas: fix test for negative unsigned and typos
[SCSI] a2091, gvp11: kill warn_unused_result warnings
[SCSI] fusion: Move a dereference below a NULL test
...
Fixed up trivial conflict due to moving the async part of sd_probe
around in the async probes vs using dev_set_name() in naming.
Convert to net_device_ops and internal net_device_stats
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Remove excess kernel-doc function parameter notation from i2o/.
Warning(drivers/message/i2o/iop.c:64): Excess function parameter 'msg' description in 'i2o_msg_get_wait'
Warning(drivers/message/i2o/device.c:62): Excess function parameter 'drv' description in 'i2o_device_claim'
Warning(drivers/message/i2o/device.c:95): Excess function parameter 'drv' description in 'i2o_device_claim_release'
Warning(drivers/message/i2o/driver.c:186): Excess function parameter 'msg' description in 'i2o_driver_dispatch'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the NULL test is necessary, then the dereference should be moved below
the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/).
// <smpl>
@disable is_null@
identifier f;
expression E;
identifier fld;
statement S;
@@
+ if (E == NULL) S
f(...,E->fld,...);
- if (E == NULL) S
@@
identifier f;
expression E;
identifier fld;
statement S;
@@
+ if (!E) S
f(...,E->fld,...);
- if (!E) S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove excess kernel-doc function parameter notation:
Warning(drivers/message/fusion/mptbase.c:964): Excess function parameter or struct member 'handle' description in 'mpt_free_msg_frame'
Warning(drivers/message/fusion/mptbase.c:5434): Excess function parameter or struct member 'portnum' description in 'mpt_findImVolumes'
Warning(drivers/message/fusion/mptbase.c:6949): Excess function parameter or struct member 'mr' description in 'mpt_spi_log_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Eric.Moore@lsi.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt fusion: clear list of outstanding commands on host reset
[SCSI] scsi_lib: only call scsi_unprep_request() under queue lock
[SCSI] ibmvstgt: move crq_queue_create to the end of initialization
[SCSI] libiscsi REGRESSION: fix passthrough support with older iscsi tools
[SCSI] aacraid: disable Dell Percraid quirk on Adaptec 2200S and 2120S
A bug in the fusion driver was exposed by the switch to block timeout.
Basically, drivers are supposed to terminate commands once error
handling begins on them. The fusion apparently wasn't doing this.
Under the old timeout regime, completions on terminated commands would
by and large get ignored because of the way command timeouts used to
work. The new block timers are very intolerant to this, though,
becuase the request gets cleaned and freed.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=12195
Reported-by: Alex Shi <alex.shi@intel.com>
Tested-by: Ming Lin <ming.m.lin@intel.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
no argument named @msg in i2o_msg_get_wait(), remove it.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix incorrect use of loose in i2o_block.c
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This triggers false bug reports as it does a bogus kmalloc with locks held
but is never really compiled into the kernel.
Closes#8329
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixup i2o kernel-doc warnings:
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:579): No description found for parameter 'bdev'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:579): No description found for parameter 'mode'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:608): No description found for parameter 'disk'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:608): No description found for parameter 'mode'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:657): No description found for parameter 'bdev'
Warning(linux-next-20081022//drivers/message/i2o/i2o_block.c:657): No description found for parameter 'mode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (21 commits)
[SCSI] sd: fix computation of the full size of the device
[SCSI] lib: string_get_size(): don't hang on zero; no decimals on exact
[SCSI] sun3x_esp: Convert && to ||
[SCSI] sd: remove command-size switching code
[SCSI] 3w-9xxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] 3w-xxxx: remove unnecessary local_irq_save/restore for scsi sg copy API
[SCSI] fix netlink kernel-doc
[SCSI] sd: Fix handling of NO_SENSE check condition
[SCSI] export busy state via q->lld_busy_fn()
[SCSI] refactor sdev/starget/shost busy checking
[SCSI] mptfusion: Increase scsi-timeouts, similariy to the LSI 4.x driver.
[SCSI] aic7xxx: Take the LED out of diagnostic mode on PM resume
[SCSI] aic79xx: user visible misuse wrong SI units (not disk size!)
[SCSI] ipr: use memory_read_from_buffer()
[SCSI] aic79xx: fix shadowed variables
[SCSI] aic79xx: fix shadowed variables, add statics
[SCSI] aic7xxx: update *_shipped files
[SCSI] aic7xxx: update .reg files
[SCSI] aic7xxx: introduce "dont_generate_debug_code" keyword in aicasm parser
[SCSI] scsi_dh: Initialize path state to be passive when path is not owned
...
Make SPI timeout 10s the same as SAS
Signed-off-by: Bernd Schubert <bs@q-leap.de>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The I2O ioctls assume 32bits. In itself that is fine as they are old
cards and nobody uses 64bit. However on LKML it was noted this
assumption is also made for allocated memory and is unsafe on 64bit
systems.
Fixing this is a mess. It turns out there is tons of crap buried in a
header file that does racy 32/64bit filtering on the masks.
So we:
- Verify all callers of the racy code can sleep (i2o_dma_[re]alloc)
- Move the code into a new i2o/memory.c file
- Remove the gfp_mask argument so nobody can try and misuse the function
- Wrap a mutex around the problem area (a single mutex is easy to do and
none of this is performance relevant)
- Switch the remaining problem kmalloc holdout to use i2o_dma_alloc
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (59 commits)
[SCSI] replace __FUNCTION__ with __func__
[SCSI] extend the last_sector_bug flag to cover more sectors
[SCSI] qla2xxx: Update version number to 8.02.01-k6.
[SCSI] qla2xxx: Additional NPIV corrections.
[SCSI] qla2xxx: suppress uninitialized-var warning
[SCSI] qla2xxx: use memory_read_from_buffer()
[SCSI] qla2xxx: Issue proper ISP callbacks during stop-firmware.
[SCSI] ch: fix ch_remove oops
[SCSI] 3w-9xxx: add MSI support and misc fixes
[SCSI] scsi_lib: use blk_rq_tagged in scsi_request_fn
[SCSI] ibmvfc: Update driver version to 1.0.1
[SCSI] ibmvfc: Add ADISC support
[SCSI] ibmvfc: Miscellaneous fixes
[SCSI] ibmvfc: Fix hang on module removal
[SCSI] ibmvfc: Target refcounting fixes
[SCSI] ibmvfc: Reduce unnecessary log noise
[SCSI] sym53c8xx: free luntbl in sym_hcb_free
[SCSI] scsi_scan.c: Release mutex in error handling code
[SCSI] scsi_eh_prep_cmnd should save scmd->underflow
[SCSI] sd: Support for SCSI disk (SBC) Data Integrity Field
...
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Compile warning:
ignoring return value of `sysfs_create_link', declared with attribute warn_unused_result.
If sysfs_create_link failed, take care of the return value and do some
error handle after the failure.
Since sysfs_remove_link() will check whether a link exists, when removing the
link in error path, we don't need to care whether a link was created.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
When the firmware is in Fault state it will be identifed only when the next time
the driver access the IOC state.
This patch includes a polling function in the driver which will be executed in
regular interval to check the status of the firmware and if it is in Fault
state, then the firmware will be reset by the driver.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The initial period is set to 0xFF
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a fault on the FC controllers that makes them not respond
correctly to MSI. The SPI controllers are fine, but are likely to be
onboard on older motherboards which don't handle MSI correctly, so
default both these cases to disabled. Enable by setting the module
parameter mpt_msi_enable=1.
For the SAS case, enable MSI by default, but it can be disabled by
setting the module parameter mpt_msi_enable=0.
Cc: "Prakash, Sathya" <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The problem here is that if the ioc faults too early in the bring up
sequence (as it usually does for an irq routing problem), ioc_reset gets
called before the scsi host is even allocated. This causes an oops when
it later schedules a renegotiation. Fix this by checking ioc->sh before
trying to renegotiate.
Cc: "Moore, Eric" <Eric.Moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Updating copyright statement to include the year 2008
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Updating driver version to 3.04.07 from 3.04.06
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the needlessly global struct mpt_proc_root_dir static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following a hard reset of a SAS raid, one of the raid targets is occasionally
missing. I tracked this down to a pretty obscure little bug.
The LSI fusion drivers for SAS and Fibre Channel both use their respective
transport layers. Those transport layers increment the target number
assigned to new targets.
The routine __scsi_scan_target uses the "this_id" element of the Scsi_Host
structure to avoid scanning the scsi host adapter. Both fusion drivers set
"this_id" from a value returned in a firmware PortFacts response. For my
particular test case (SAS) the firmware id assigned to the initiator was
173. After enough raid resets to cause the raid targets to go and come a
sufficient number of times, the id assigned by the transport to a raid
target would match the id assigned by the host adapter to the "this_id"
field, resulting in that target not being scanned.
Fix by not assigning this_id and not checking it in slave_configure.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a problem with the combination of the upstream power
management fixes and the enabling of MSI by default in that the
suspend path still uses the global variable. Convert it to check
ioc->msi_enable.
Cc: "Moore, Eric" <Eric.Moore@lsi.com>
Cc: "Prakash, Sathya" <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While performing hardware raid reset testing via the raid's client, I
noticed that sometimes, following the reset, that there would be more
raid targets in the lsscsi output than there actually were raid
targets. I tracked this down to the following issue.
Fusion cannot always find the mptsas_portinfo structure for the hba
because it uses the handle stored in ioc->handle to locate it. The
problem is that the firmware can change the handle associated with the
hba when h/w raid is reset (via the raid client). When this happens,
the driver will allocate another mptsas_portinfo structure and link it
into the chain of said structures. This ultimately causes confusion
within the driver resulting in targets not being removed when they
should be.
Eric Moore pointed out that the hba's portinfo structure is always the
first structure on the sas_topology list. This patch modifies
mptsas.c to access the hba's portinfo structure by taking the first
structure on said list.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
the semaphore inactive_list_mutex is used as a mutex, convert it to
the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the driver to enable MSI by default for all SAS chips.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The system power state changes like hibernation and standby are not happening
properly with 106XE controllers, this patch modifies the driver to free
resources and allocate resources in power management entry points
[jejb: compile fixes for upstream]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Don't oops if NumPhys==0, instead return -ENODEV.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=9909
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix docbook problems in fusion source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ioc->name is used in the printk's after ioc has been freed. Free
after prinks to fix this.
This patch fixes two use-after-free's introduced by
commit e78d5b8f1e and spotted by the
Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Verified all the arches necessary select the CONFIG_64BIT symbol. This
also kills the warning (since it was using the 32-bit case) on parisc64
and mips64.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the I/O resource allocation behavior of FUSION
driver. The current version of driver allocates the I/O resources
even if they are not required and this creates trouble in low resource
environments. This driver now uses
pci_enable_device_mem/pci_enable_device functions to differentiate the
resource allocations.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch sets the IOC pointer in drvrdata of pcidev before adding
the IOC into the list of IOCs. Without this patch the driver oops when
the mptsas and mptctl modules are loaded in parallel.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts i2o_block to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, i2o_block_end_request(),
is changed.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes the module unload problem in flash less 1030
controller environment where firmware download boot functionality is
invoked. The problem is due to the firmware download is being done in
the reverse order, which this patch solves by insureing the download
occurs to the last controller being reset.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch fixes mptsas_smp_handler to update both din_resid or
dout_resid on success. bsg can report back the residual.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
drivers/message/i2o/exec-osm.c:539: warning: `i2o_exec_lct_notify' defined but not used
comes when CONFIG_I2O_LCT_NOTIFY_ON_CHANGES=n, because its only callsite
is #ifdef'ed as such. So let's #ifdef the function definition also. Also
move the definition to before the callsite, to get rid of forward prototype.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-api docbook warnings.
Warning(linux-2.6.23-git8//drivers/message/fusion/mptscsih.c:2618): No description found for parameter 'sc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/message/fusion/mptctl.c: In function ‘mptctl_mpt_command’:
drivers/message/fusion/mptctl.c:1764: warning: ‘bufIn.len’ may be used uninitialized in this function
drivers/message/fusion/mptctl.c:1765: warning: ‘bufOut.len’ may be used uninitialized in this function
come because gcc gets confused by some "goto" statements in above
function. The warnings have been verified to be bogus, however, the
function does initialize these later (after the offending goto's) in
the function anyway. So let's move those initializations to top of
function, thereby also shutting up these warnings.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
NB = number of blocks. This represents the number of blocks to
transfer. The block size is based on the message frame size provided
in the ioc_facts. A value of zero indicates the entire message frame
should be copied. This is two bit value. So by setting this to
non-zero vaule, you increase performance by reducing amount of data
needing to be dma'd. The value that is stored in ioc->ReqeustNB is
sometimes a non-zero vaule, which creates a bug in mptlan, where not
the entire message frame is getting transfer to firware, resulting in
corruption. This fix sets the default to zero, thus entire message
frame is copied.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up prints that use the xxx_printk API, in that the fusion
preamble "mptbase: iocX" follows the info provided by the print API.
The way its currently coded, the [H:C:T] print in sdev_printk will be
inbetween "mptbase" and "iocX", instead of before.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ScsiLookup is an array of pending scmd pointers that the scsi lld
maintains. This array is touched from queuecommand, eh threads, and
interrupt context. This array should put under locks, hence this patch
to synchronize its access. I've added some nice little function
wrappers for this, and moved the ScsiLookup array over to MPT_ADAPTER
struct.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
List below is output from C=2 sparse compilation, which are fixed with
this patch.
1) mptspi: pg0 is defined in x86 version of include/asm/pgtable.h
2) mptsas: context imbalance in 'mptsas_probe' different lock contexts
for basic block
3) mptbase: from mpt_attach - cast adds address space to expression
4) mptbase: from mpt_do_upload - request[] is bad constant expression
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is currently typecasting to obtain the shost hostdata. The
driver is updated to use the shost_priv macro.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding 949X, 949E, and 1078 to Kconfig. Adding "depends on FUSION"
required in the FUSION_LOGGING section, and fixing a spelling error.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some other vender has concerns over this copyright, and Dell has
approved removing it.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up code by accesing the ioc pointer directly instead of via hd->ioc. In the future, most data members of struct MPT_SCSI_HOST will be either deleted or moved to struct MPT_ADAPTER.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
common naming of vdevice through out driver
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
cleaning up some white space that was introduce in a recent "cb_idx int to u8" patch.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Standardize all prints using common MYIOC_s_XXX_FMT macro defined in mptbase.h. Currently the driver uses several different methods to display info, where in some cases the "controller name" generating the printk is not provided.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
alloc_fcdev() calls alloc_netdev() which uses kzalloc to alloc all the
memory together with dev->priv region hence no zeroing of structs inside
struct mpt_lan_priv needed.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker spotted two potential memory leaks in
drivers/message/fusion/mptbase.c::mpt_attach().
There are two returns that may leak the storage allocated for 'ioc'
(sizeof(MPT_ADAPTER) bytes).
A simple fix would be to simply add two kfree() calls before the return
statements, but a better fix (that this patch implements) is to reorder the
code so that if we hit the first return condition we don't have to do the
allocation at all and then just add a kfree() call for the second case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recently LSI Logic Corp was renamed as LSI Corp, so whereever there is
a reference of LSI Logic, it is changed to LSI in mpt fusion driver
code.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When there is state change in FC links, a message is displayed with
old and new link speed.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The data structure definitions from mptsas.c are moved to a new header
file mptsas.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The call back index requires only u8 but in lot of places it is
referred as int, now everywhere the call back index variables are
declared as u8 with uniform name cb_idx
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Added support for sending the task management requests through High priority
request FIFO instead of Doorbell writes when firmware support High priority
FIFO.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Per request from Matthew Wilcox - using PCI_VENDOR_ATTO.
Add support for ATTO UL4D, they are rebranded 53C1030.
The changes are
1. Adding a new PCI vendor ID in pci table
2. The spi_port_page_2 is in different format than that of LSI generic
spi_port_page_2 and hence mapping code is added.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/message/i2o/i2o_block.c: In function 'i2o_block_transfer':
drivers/message/i2o/i2o_block.c:837: warning: integer overflow in expression
msg->u.head[1] = cpu_to_le32(I2O_CMD_PRIVATE << 24 | HOST_TID << 12 | tid);
and I2O_CMD_PRIVATE is defined as 0xFF. This gets "0xFF0100 | tid" and fits
into 32-bit unsigned but not into 32-bit signed integer properly. Target
value is defined as u32 so the claculation does not fit during computation.
Change local variable tid to u32 so the whole expression is of u32 type and
fits well into u32 result.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Cc: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for SAS Management Protocol (SMP) passthrough
support via bsg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wire up the mpt_debug_level module parameter so you can write to the
/sys/module/mptbase/parameters/mpt_debug_level and have it take effect
in every ioc.
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
This patch contains changes in mptctl.c to support logging in MPT fusion drivers
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptfc.c, mptlan.c, mptsas.c and mptspi.c to
support logging in MPT fusion drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptscsih.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new sysfs attribute is added to retrieve and modify the debug level.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains changes in mptbase.c to support logging in MPT fusion
drivers.
The changes are majorly in debug printks, the existing debugprintk are
modified accroding to new debug macros defined in the file mptbdebug.h
A new module parameter mpt_debug_level is added to pass the debug level as
module parameter.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a new file mptdebug.h in the fusion source directory,
which contains different debug macros. The existing debug macros and
flags are removed from the mptbase.h and Makefile In Kconfig a new
configuration parameter FUSION_LOGGING is added to enable/disable the
logging support during compile time.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Update help in Kconfig for mptfc driver to indicate the driver supports
Brocade FC 4G HBA.
signed-off-by: Gwendal Grignou <ggrignou@brocade.com>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Brocade 410/420 4Gbit FC HBAs.
They are re-branded LSI HBAs [LSI7104EP-LC/LSI7204EP-LC]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The mptspi and mptsas drivers are modified to deregister from transport layer
if registration with PCI driver failed
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New sysfs scsi_host attributes are added to provide information about Firmware
version, BIOS version, MPI version and other product related information
signed-off-by: Sathya Praksh <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix oops on reading from some i2o proc files (i2o_seq_show_driver_store() and
other) because their handlers uses "exec" field in struct i2o_controller
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to free i2o msg in case of error.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes access to memory that has not been allocated:
i2o_msg_get_wait() can returns errors different from I2O_QUEUE_EMPTY. But the
result is checked only against this code. If it is not I2O_QUEUE_EMPTY then
we dereference the error code as the pointer later.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a number of issues in i2o_cfg_passthru{,32}:
- i2o_msg_get_wait() return vaile is not checked;
- i2o_message memory leaks on error paths;
- infinite loop to sg_list_cleanup in passthru32
It's important issue because of i2o_cfg_passthru is used by raidutils for
monitorig controllers state, and in case of memory shortage it leads to the
node crash or disk IO stall.
[akpm@linux-foundation.org: fix null-ptr deref]
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make some offending drivers depend on it and set CONFIG_ARCH_NO_VIRT_TO_BUS
for ppc64 so that we don't build those drivers.
This gets PowerPC allmodconfig and allyesconfig much closer to building.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The I2O driver uses two semaphores as mutexes. Use the mutex API instead of
the (binary) semaphores.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
drivers/message/i2o/device.c:i2o_parm_field_get() unnecessarily passes
GFP_ATOMIC (along with GFP_KERNEL) to kmalloc() from a context that is not
atomic. Remove the pointless GFP_ATOMIC.
Signed-off-by: Satyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If there is IO going to the volume while a hidden disk is being torn down,
there is a case where we would return a DID_NO_CONNECT for IO sent to the
volume. The end result is the volume goes read-only. This problem is due to the
fact the firmware mapped target ids saved in per device object is phys_disk_num
for hidden raid components, and target_id for the volume. There is a single
case when both phys_disk_num and target_id are equal, so enters this issue. We
fix this issue by checking the tflags when the device is torned down,
insuring the IO being completed is meant for hidden raid component, not the
volume. In addition to this fix, there are a couple other cases to address
hidden raid components. For instance task_abort and device reset are not
supported by mpt fw for hidden raid components, a bus reset would be required
or target reset to volume.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
nice cosmetic cleaning of eh thread callback funtions
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
rewrite of mpt_fc_log_info to use the enum/defines from mpi_log_fc.h
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update assocated fusion sources with new support email address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Note: needs to change i2o_dma_map_sg when the chaining sg is ready.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch for: http://bugzilla.kernel.org/show_bug.cgi?id=8426
A recent code cleanup that moved code from mptscsih to mptspi
inadvertently change the order some code was called. This caused
a massive slowdown (of 150x to 300x) on the CD/DVD drive on the
high-end HP Integrity servers.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
TODO: use scsi_for_each_sg().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] megaraid_sas: intercept cmd timeout and throttle io
[SCSI] fusion: Fix |/|| confusion
[SCSI] aic94xx: asd_clear_nexus should fail if the cleared task does not complete
[SCSI] aic7xxx: fix aicasm build failure with gcc-3.4.6
[SCSI] aacraid: apply commit config for reset_devices flag
[SCSI] sd: fix refcounting regression in suspend/resume routines
[SCSI] aacraid: fix panic on short Inquiry
[SCSI] aacraid: Correct sa platform support. (Was: [Bug 8469] Bad EIP value on pentium3 SMP kernel-2.6.21.1)
[SCSI] NCR53C9x: correct spelling mistake in deprecation notice
[SCSI] tgt: fix a rdma indirect transfer error bug
[SCSI] MegaRAID: Update MAINTAINERS email-id
[SCSI] stex: minor cleanup and version update
[SCSI] stex: fix reset recovery for console device
[SCSI] stex: extend hard reset wait time
[SCSI] stex: fix id mapping issue
[SCSI] ipr: Proper return codes for eh_dev_reset for SATA devices
[SCSI] zfcp: IO stall after deleting and path checker changes after reenabling zfcp devices
[SCSI] zfcp: avoid clutter in erp_dbf
There is no reason i2o_max_drivers must be a power of two. This patch
eliminates such a constraint.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maximum number of I2O drivers which could be registered is configurable by
max_drivers module parameter.
But the module parameter is ignored and default value (I2O_MAX_DRIVERS = 8)
is used in the loops to notify all registered drivers.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2o_driver_register() initalizes event queue for driver only when
drv->event is set. So similarly the event queue should be destroyed only
when drv->event is set in the error path. Otherwise destroy_workqueue()
will called with NULL.
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several cases where the fusion driver uses the logical || to
try to do an arithmetical or ... fix by replacing with |.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Refine some depends statements to limit their visibility to the
environments that are actually supported.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After host reset, the device are programmed to default asyn narrow nego.
We need to reprogram the parameter back to previous values. If the host
reset is called as a result of spi_dv_device() commands timing out, its
possible to get into an infinite loop of dv to host reset. This will
prevent that case, as we merely program old values. If host reset is
called outside context of domain validation, then we can call
spi_dv_device.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I2O subsystem has been broken in mainstream several months ago (after
2.6.18). Commit 4aff5e2333 from Jens
Axboe split struct request ->flags into two parts: cmd_type and
cmd_flags.
In i2o layer this patch has replaced flag REQ_SPECIAL by the according
cmd_type. However i2o has used REQ_SPECIAL not as command type but as
driver-specific flag for the debug purposes. As result all i2o requests
have type "special" now, are not processed to the hardware and fail with
I/O error:
i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
unable to read partition table
block-osm: device added (TID: 207): i2o/hda
The following patch removes the extra debug checks without any drawbacks and
restores the normal driver's work.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This address the issue of VMWare guest OS being remounted as read-only
becuase the underlying device was held busy too long and at the
same time address Engenio MPP driver concerns over infinite retries.
This patch removes the code that snoops the SAM STATUS on busy, which
would be returning DID_BUS_BUSY, instead we return the status as is.
Retry hanlding seems to be properly handled in scsi_softirq_done,
where a busy sam status would only occurr for the time specified by
(cmd->allowed +1) * cmd->timeout_per_command.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Honour the return value of pci_enable_device(), which
seems to be a desirable thing to do:
2.6.20-rc4
gcc (GCC) 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)
CC [M] drivers/message/fusion/mptbase.o
drivers/message/fusion/mptbase.c: In function `mpt_resume':
drivers/message/fusion/mptbase.c:1541: warning: ignoring return value
of `pci_enable_device', declared with attribute warn_unused_result
It also in turn has mptscsih_resume() honour the return value of
mpt_resume()
I'm not sure about the handling of the other potential error cases
in mpt_resume(), of which there appear to be many. But this does
seem to be a good start.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It seems that most of the code in mptscsih_resume() doesn't
do anything. This patch removes that code.
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fix's an oops during driver load time. mptsas_probe calls
mpt_attach(over in mptbase.c). Inside that call, we read some
manufacturing config pages to setup some defaults. While reading the
config pages, the firmware doesn't complete the reply in time, and we
have a timeout. The timeout results in hardreset handler being called.
The hardreset handler calls all the fusion upper layer driver reset
callback handlers. The mptsas_ioc_reset function is the callback
handler in mptsas.c. So where I'm getting to, is mptsas_ioc_reset is
getting called before scsi_host_alloc is called, and the pointer ioc->sh
is NULL as well as the hostdata.
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@sdl.org: dvb fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bump version, and fix email addr for lsi support
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
misc error handling bug fix's
- properly interpret iocstatus returned after task management request
- clear tmState after a failed doorbell
- cleanup mptscsih_taskmgmt_complete
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return proper sas address to sas transport layer for parent phys that
form a wide port. Current implementation returns a different address
for each phy, incremented by one from the base address.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fusion firmware requires target reset following hotplug removal event,
with purpose to flush target outstanding request in fw. Current implementation
does the target resets from delayed work tasks, that in heavy load
conditions, take too long to be invoked, resulting in command time outs
This patch will issue target reset immediately from ISR context, and will
queue remaining target resets to be issued after the previous one completes.
The delayed work tasks are spawned during the target reset completion.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
inactive raid support, e.g. exposing hidden raid components
belonging to a volume that are inactive. Also misc bug fix's for
various raid asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
various string updates for iocstatus, logingo, and fw asyn events.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move some functions that only apply to the mptspi module over from mptscsih.c
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for greater than 255 target and luns.
Kill the hd->Target[] field, and change all references
of bus_id/target_id, to channel/id.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here are the lastest mpi headers for mpt fusion driver, which defines
the firmware to driver interface.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes the mptctl pass through available if
the mptsas driver is selected. Without this patch
if mptsas is the only fusion driver chosen, then
the mptctl is not presented as an option.
smp_utils uses the mptctl driver to pass SAS SMP
functions through a MPT SAS HBA.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Add modinfo driver version support.
* Change copyright year to 2007.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Endian fix's for warnings found in ppc environment.
* Fix compile time warning when calling scsi_device_reprobe, where
in newer kernels this API expects its return value to be examined.
* Fix compile errors when debug messages are enabled.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A repost of a patch forwarded by Mikael Reed from 2006-12-20.
The fibre channel IOC may kill a request for a variety of
reasons, some of which may be recovered by a retry, some of
which are unlikely to be recovered. Return DID_ERROR
instead of DID_RESET to permit retry of the command,
just not an infinite number of them.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i2o_exec_exit and i2o_driver_exit were marked as __exit which is a bug
because both are invoked from __init and __exit functions.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With I2O_CONFIG=y and I2O_EXT_ADAPTEC=n, kernel build gets:
drivers/message/i2o/i2o_config.c:1115: error: 'i2o_cfg_compat_ioctl' undeclared here (not in a function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle __copy_from_user() return value.
Noticed by inspection, not from build warning.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i2o_scsi: handle sysfs failure
i2o_device:
* convert i2o_device_add() to return integer error code
rather than pointer. Fortunately -nobody- checks the return code of
this function, so changing has nil impact.
* handle errors thrown by device_register()
More work in i2o_device remains.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Change drivers/message/i20 pci driver to simply do a nestable
enable()/disable() instead of checking for it.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Thanks to James Smart for the inspiration.
Stall error handler if attempting recovery while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Also verify that VirtDevice is available before issuing scsi command.
VirtDevice is removed when fc transport removes a target.
See James Smart's patch of 08/17/2006 for greater detail.
http://marc.theaimsgroup.com/?l=linux-scsi&m=115583213624803&w=2
Also bump version number per Eric's request.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Eric Moore <eric.moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Just like everyone else.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Use the safe ref-counted API for the bridge check
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This flag denotes local attachment of the phy. There are two problems
with it:
1) It's actually redundant ... you can get the same information simply
by seeing whether a host is the phys parent
2) we condition a lot of phy parameters on it on the false assumption
that we can only control local phys. I'm wiring up phy resets in the
aic94xx now, and it will be able to reset non-local phys as well.
I fixed 2) by moving the local check into the reset and stats function
of the mptsas, since that seems to be the only HBA that can't
(currently) control non-local phys.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add host_supported_speeds, host_maxframe_size, host_speed, host_fabric_name,
host_port_type, host_port_state, and host_symbolic_name transport attributes
to fusion fibre channel.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch corrects a problem in mptfc which can result in targets
being removed after executing an "lsiutil 99" reset of the fibre
channel ports.
The last rescan event was being processed before the setup reset work
due to an inappropriate optimization in the event processing logic.
Every rescan event is now queued for execution and the setup reset
work now executes in the proper sequence.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based upon a conversation I had with LSI's fibre channel firmware guru,
this patch adds another condition under which the driver waits for the
firmware link initialization / target discovery to complete.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This takes advantage of the sas class backlink function to show which
port on an expander is used to communicate with the parent.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (38 commits)
[SCSI] More buffer->request_buffer changes
[SCSI] mptfusion: bump version to 3.04.01
[SCSI] mptfusion: misc fix's
[SCSI] mptfusion: firmware download boot fix's
[SCSI] mptfusion: task abort fix's
[SCSI] mptfusion: sas nexus loss support
[SCSI] mptfusion: sas loginfo update
[SCSI] mptfusion: mptctl panic when loading
[SCSI] mptfusion: sas enclosures with smart drive
[SCSI] NCR_D700: misc fixes (section and argument ordering)
[SCSI] scsi_debug: must_check fixes
[SCSI] scsi_transport_sas: kill the use of channel
[SCSI] scsi_transport_sas: add expander backlink
[SCSI] hide EH backup data outside the scsi_cmnd
[SCSI] ibmvscsi: handle inactive SCSI target during probe
[SCSI] ibmvscsi: allocate lpevents for ibmvscsi on iseries
[SCSI] aic7[9x]xx: Remove last vestiges of reverse_scan
[SCSI] aha152x: stop poking at saved scsi_cmnd members
[SCSI] st.c: Improve sense output
[SCSI] lpfc 8.1.7: Change version number to 8.1.7
...
Fix's to insure download boot could occur when
either channel of 1030 is reset. Necessary in order
for onboard controller in flashless environment
to become operational.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix's to insure proper status is returned to midlayer
when a task abort failed to be aborted by controller
firmware.
Also sanity checks to prevent scsi cmd from being
double completed during error recovery.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas nexus loss support for systems that suport failover.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix panic for when mptctl is loading at the same time
when one of the fusion llds (mptsas/mptfc/mptspi) is loading.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding support for sas enclosures with smart drives.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Using the port_id for the channel is completely unnecessary since the
host_id/target_id are constructed to be globally unique. Also move
the mptsas driver on to virtual channel 1 for its raid devices.
Acked-by: "Moore, Eric" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a proper prototype for i2o_parm_issue() in core.h.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows us to be rid of the machinery in mptsas for creating and
tracking port numbers. Since mptsas is merely inventing the numbers,
the SAS transport class may as well do it instead.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the current problems the mptsas driver has is that of "ghost"
devices (these are devices the firmware reports as existing, but what
they actually represent are the parents of a lower device), so for
example in my dual expander configuration, three expanders actually show
up, two for the real expanders but a third is created because the
firmware reports that the lower expander also has another expander
connected (which is simply the port going back to the upper expander).
The attached patch eliminates all these ghosts by not allocating any
devices for them if the SAS address is the SAS address of the parent.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The way mpt_interrupt() was coded, it was impossible for the unhandled
interrupt detection logic to ever trigger. All interrupt handlers should
return IRQ_NONE when they have nothing to do.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
Conflicts:
drivers/scsi/aacraid/comminit.c
Fixed up by removing the now renamed CONFIG_IOMMU option from
aacraid
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Adding 1078 ROC (Raid On Chip) Support - New host adapter
* Moving all PCI Vendor/Device ids to using internal defines; a request
from Christoph/James B. some time ago for when the next chip was added.
* Removing SAS 1066/1066E Vendor/Device IDs, as there are no plans to
manufacture that controller.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Wide port support added - using James Bottomley's new SAS wide port API.
(There is a known problem in sas transport layer reported yesterday to
James. The Kobject dev.bus_ids for end devices are not unique across
expanders. I have added a work around in this patch, where I asigning
an unique port identifier for every port within the host - this solves
the problem, but I expect a fix from James in the sas transport).
* Adding target_alloc and target_destroy entry points, and moving code over
from the slave entry points.
* The renaming of some mptscsih_xxx functions declared in mptsas.c,
to mptsas_xxx.
* Target Reset moved from slave_destroy to hotplug work thread
handling (with regard to device removal). Also inhibit IO to end device
while device is being broken down . Talked to James Smart about this
at Linux Expo (with questions of how the fc transport handles this).
* Cleaning up the kzalloc's, and kfree's
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's available in a header as a static inline - there's no need to export it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
With Achim patch the last user (gdth) is switched away from scsi_request
so we an kill it now. Also disables some code in i2o_scsi that was
broken since the sg driver stopped using scsi_requests.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bump driver version number to reflect addition of various
fibre channel patches.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver uses msleep_interruptible() in the code path responsible
for resetting the card's ports via the lsiutil command. If a
<ctrl-c> is received during the reset it can leave a port in such
a state that the only way to regain its use is to reboot the system.
Changing from msleep_interruptible() to msleep() corrects the problem.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While doing board reset testing I was able to put the system in
an infinite request/response loop between the scsi layer and
mptscsih_qcmd() by aborting the reset. This patch installs
a "SETUP RESET" handler which calls fc_remote_port_delete()
for all registered rports. This blocks the target which
prevents the loop. Additionally, should the reset fail to
complete, the transport will now terminate i/o to the target.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The fibre channel firmware provides a timer which is similar in purpose
to the fibre channel transport's device loss timer. The effect of this
timer is to extend the total time that a target will be missing beyond
the value associated with the transport's timer. This patch changes
the firmware timer to a default of one second which significantly reduces
the lag between when a target goes missing and the notification of the
fibre channel transport.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move fibre channel event and reset handling to mptfc. This will
result in fewer changes over time that need to be applied to
either mptbase.c or mptscsih.c.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Avoid JBUS errors on some Niagara systems.
[FUSION]: Fix mptspi.c build with CONFIG_PM not set.
[TG3]: Handle Sun onboard tg3 chips more correctly.
[SPARC64]: Dump local cpu registers in sun4v_log_error()
From: Markus Lidel <Markus.Lidel@shadowconnect.com>
- Fixed locking of struct i2o_exec_wait in Executive-OSM
- Removed LCT Notify in i2o_exec_probe() which caused freeing memory and
accessing freed memory during first enumeration of I2O devices
- Added missing locking in i2o_exec_lct_notify()
- removed put_device() of I2O controller in i2o_iop_remove() which caused
the controller structure get freed to early
- Fixed size of mempool in i2o_iop_alloc()
- Fixed access to freed memory in i2o_msg_get()
See http://bugzilla.kernel.org/show_bug.cgi?id=6561
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MPT fusion driver initialization fails while second kernel is booting,
after a system crash (if kdump kernel is configured). Oops message is
pasted below.
*****************************************************************************
Fusion MPT base driver 3.03.08
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SAS Host driver 3.03.08 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
mptbase: Initiating ioc0 bringup
BUG: unable to handle kernel paging request at virtual address 00002608
printing eip:
c11782fd
*pde = 00000000
Oops: 0000 [#1]
Modules linked in:
CPU: 0
EIP: 0060:[<c11782fd>] Not tainted VLI
EFLAGS: 00010046 (2.6.17-rc1-16M #2)
EIP is at mptscsih_io_done+0x27/0x3a3
eax: c4fed000 ebx: c4fed000 ecx: 00002600 edx: 00000298
esi: c11782d6 edi: 00002600 ebp: 00000000 esp: c1332f74
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c1332000 task=c128f9c0) Stack: <0>0000006c 00000020 00000298 00002600 c4fed000 c4fed000 c11782d6 0000260 0
00000000 c1172c49 c4fed000 c1305b40 00000005 00000000 c1172d75 c48877e0
c1029687 00000000 c1307fb8 00000000 c1305a00 00000001 00000000 c1307fb8
Call Trace:
<c11782d6> mptscsih_io_done+0x0/0x3a3 <c1172c49> mpt_turbo_reply+0xbb/0xd3
<c1172d75> mpt_interrupt+0x22/0x2b <c1029687> misrouted_irq+0x63/0xcb
<c10297b3> note_interrupt+0x43/0x98 <c10292f9> __do_IRQ+0x68/0x8f
<c1003fac> do_IRQ+0x36/0x4e
=======================
<c1002aa6> common_interrupt+0x1a/0x20 <c1001150> mwait_idle+0x1a/0x2a
<c10010bf> cpu_idle+0x40/0x5c <c1308610> start_kernel+0x17a/0x17c Code: 5e 5f 5d c3 55 89 cd 57 56 53 83 ec 14 89 54 24 0c 89 44 24 10 8b 90 cc 00 00 00 8b 4c 24 0c 81 c2 98 02 00 00 85 ed 89 54 24 08 <0f> b7 79 08 89 fe 74 04 0f b7 75 08 66 39 f7 75 0d 8b 44 24 0c
*******************************************************************************
o Kdump capture kernel boot fails during initialization of MPT fusion driver.
(LSI Logic / Symbios Logic SAS1064E PCI-Express Fusion-MPT SAS (rev 01))
o Problem is easily reproducible, if system crashed while some disk activity
like cp operation was going on.
o After a system crash, devices are not shutdown and capture kernel starts
booting while skipping BIOS. Hence underlying device is left in operational
state. In this case scsi contoller was left with interrupt line asserted
reply FIFO was not empty. When driver starts initializing in the second
kernel, it receives the interrupt the moment request_irq() is called.
Interrupt handler, reads the message from reply FIFO and tries to access
the associated message frame and panics, as in the new kernel's context
that message frame is not valid at all.
o In this scenario, probably we should delay the request_irq() call. First
bring up the IOC, reset it if needed and then should register for irq.
o I have tested the patch with SAS1064E and 53c1030 controllers.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All registered reset callback handlers are called during reset processing.
The mptspi modules has its own reset callback handler, just recently
added for issuing domain validation after host reset. If either the mptsas or
mptfc driver are loaded, this callback could be called. Thus resulting
in domain validation being issued for sas or fibre end devices.
Fix this by having mptbase.c check the bus type against the driver
type and only call the reset handler if they match (or if it's a
non-bus specific reset handler).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A race condition exists in mptfc between the thread registering a device
with the fc transport and the scan work generated by the transport.
This race existed prior to the application of the mptfc bug fix patch.
mptfc_register_dev() calls fc_remote_port_add() with the FC_RPORT_ROLE_TARGET
bit set in the rport ids passed to the function. Having this bit set causes
fc_remote_port_add() to schedule a scan of the device.
This scan can execute before mptfc_register_dev() can fill in the dd_data
in the rport structure. When this happens, mptfc_target_alloc() will fail
because dd_data is null.
Attached is a patch which fixes the problem. The patch changes the rport ids
passed to fc_remote_port_add() to not have the TARGET bit set. This prevents
the scan from being scheduled. After mptfc_register_dev() fills in the rport
dd_data field, fc_remote_port_rolechg() is called, changing the role of the
rport to TARGET. Thus, the scan is scheduled after dd_data is filled
in which prevents the failure in mptfc_target_alloc().
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a bug fix for mptspi driver, where after a host reset or
resume, we revalidate the negotiation parameters for all devices.
This bug was introduced when the driver was ported to use the spi
transport layer.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fix for stack overflow in EventDescriptionStr, (a function
for debuging firmware events). We allocated 50 bytes on local stack
for buff[], however there are places in the code where we've attempted
copying in greater than 50 bytes into buff[].
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
mptbase.h
bump version number to 3.03.09
remove unneeded flags
define workq and remove old fc specific locks
mptbase.c
initialize new lock and don't initialize two removed locks
mptscsih.c
when firmware reports target is no longer there, return
DID_REQUEUE for fc hosts so that i/o doesn't get killed until
the transport has an opportunity to manage the loss via its
dev loss timer
when the "eh_abort" routine is called, check to see if the
driver has the command or not before looking to see if a reset
is pending. James Smart and I talked about this and believe
that the API for this routine is: if driver doesn't have
command, return SUCCESS. This change helps prevent a target
from being taken offline. SUCCESS is returned because it's
likely that the command completed after error recovery timed
it out but before it could be aborted.
provide a routine to queue work to newly created workq, and
use it.
remove "ioc" from mptscsih_abort() it was only used one time.
the other references were via hd->ioc, so I just moved it....
net change in references to ioc via hd->ioc is zero
move hd->resetPending test and hd->timeouts increment to after
the test for whether the command to be aborted remains known
to the driver
Make certain that the workq exists before queuing work to it.
mptfc.c
no longer need to lock rport data structures as I was able to
single thread the code! I fixed up the debug code to
eliminate compilation messages due to type mismatch in the
printk. Got rid of some no longer needed rport flags.
Initialize and destroy the workq used for the rescan work.
simplify the logic regarding the increment of
fc_rescan_work_count. use post increment and test for zero
vs. pre increment and test for one; eliminate work_count
variable: queue_work can be called with the work_lock held as
it doesn't sleep
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch handles case where raid hidden components
are not being removed when power turned off to device
attached to expander, as well as the case of
exposing raid components when power is turned back on
to devices attached to an expander. (This is a repost
of this patch, with mptsas_is_end_device declared
further up in the code.)
This patch contains some other miscellaneous bug fix's.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Driver panic when RAID logical volume was present when driver
loaded, or when a RAID logical volume was created on the fly.
This issue was created in due to recent scsi_transport_sas change,
when sas_read_port_mode_page was added into the mptsas drivers
slave_config entry point.
This new API expects that all sdev's to be assocated to an rphy, however
that is not the case for logical volumes, as they are created using
scsi_add_device, instead of sas_rphy_add().
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The conversion of mptsas should allow the elimination of the contained
flag in the sas transport class.
Acked-by: "Moore, Eric" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds support for hot adding and removing
expanders, and its associated attached devices.
When there is a change in topology,
the fusion firmware sends the
MPI_EVENT_SAS_DISCOVERY event to the driver.
The driver will read firmware config pages
to determine what changes took place, and refresh
drivers view of the world stored in ioc->sas_topology.
Here is the details of the action the driver does:
(1) Expander Added : The mptsas_discovery_work
workqueue is called. Config pages read, and
ioc->sas_topology is refreshed. The sas_phy_add()
is called for each phy of the expander. The
expanders attached devices are added via
sas_rphy_add(). Added end devices are handled within
the MPT_ADD_DEVICE logic in mptsas_hotplug_work
workqueue.
(2) Expander Delete : The sas_rphy_delete() will be
called for the top most compenent of the parent that the
expander is attached to. The sas_rphy_delete call
will delete all the children phys, rphys, and end devices.
This is handled from mptsas_discovery_work workqueue.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Suppport for exposing hidden raid components
for sg interface. The sdev->no_uld_attach flag
will set set accordingly.
The sas module supports adding/removing raid
volumes using online storage management application
interface.
This patch rely's on patch's provided to me
by Christoph Hellwig, that exports device_reprobe.
I will post those patch's on behalf of Christoph.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changelog:
(1) fix memory leak: p->phy_info
(2) initialize device_info and port_info data fields
(3) initialize the hba firmware handle
(4) initialize phy_id for attached phy_info data fields
(5) initialize attached phy_info data fields
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanup of mptsas firmware event handlers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It makes no sense in keeping the target_id and bus_id
in the VirtDevice structure, when it can be obtained
from the VirtTarget structure.
In addition, this patch fix's couple compilation bugs
in mptfc.c when MPT_DEBUG_FC is enabled. This
provided by Micheal Reed.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch previously provided from Adrian Bunk <bunk@stusta.de>,
moving some functions to static. This is already in
the -mm tree.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Created a debug level MPT_DEBUG_VERBOSE_EVENTS.
Moving some of the more vebose debug messages
for firwmare events into new debug level. Also
added some more firmware events descriptions.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This header is provided to better understand
loginfo codes returned by the mpt fusion firmware.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It was actually rendered unused by the move to the spi transport
class, but never taken out.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
i2o_exec_lct_modified() does not release memory allocated for work_struct.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Although your patch is the same, i've rewritten it a little bit for
naming consistency in the I2O driver.
Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the first half of a patch to add the generic domain validation
to mptspi. It also creates a secondary "virtual" channel for raid
component devices since these are now exported with no_uld_attach.
What Eric and I would have really liked is to export all physical
components on channel 0 and all raid components on channel 1.
Unfortunately, this would result in device renumbering on platforms with
mixed RAID/Physical devices which was considered unacceptable for
userland stability reasons.
Still to be done is to plug back the extra parameter setting and DV
pieces on reset and hotplug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds support to retrieve the enclosure and bay identifiers. This patch
is from Eric with minor modifications from me, rewritten from a buggy
patch of mine, based on the earlier CSMI implementation from Eric..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removes wierd humor, and bad language printk in mptlan.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=5923
When a scsi command failed, an oops would result.
Back-to-back SMART queries would make the Seagate drives unhappy. The
second SMART query would timeout, and the command would be aborted.
Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Kenny Simpson <theonetruekenny@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix's firmware download ioctl to work with SAS.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moving the toolbox call from mptbase.c, over to
mptctl.c, and using the mptctl infastructure to issue
the call. The existing code is hanging on certain HP platforms
when this ioctl is issued, and this patch fix's that.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bug fix for correctly setting sense width
for the MPTCOMMAND ioctl.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use the hard coded value MPTCTL_EVENT_LOG_SIZE to fix
bug where in certain cases, the ioc->eventLogSize was
initialized.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change from using wait_event_interruptible_timeout to
wait_event_timeout. Also delete white space and duplicate
line of code.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add bus_type recognization in ioctl path for SAS.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds support for new function types in
the existing MPTCOMMAND ioctl.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- This controller violates the I2O spec for the I/O registers. The patch
contains a workaround which moves the registers to the proper location.
(originally author: Matthew Starzewski)
- If a message frame is beyond the mapped address range a error is
returned.
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If PCI device is enabled before probing, it will not be disabled at exit.
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a sanity check in the interrupt routine
insures incoming message frames are a valid
message frames.
The code for setting 0xdeadbeaf in the freed message
frames, apparently was already submitted by Christoph
in previous patch submission.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch inhibits sending spi negotiation parameters
for non-configured devices from the slave_destroy function.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ioc->alt_ioc->alt_ioc pointer is not getting cleared
during driver unload time. This dangling pointer
can result in panic in certain circumstances, such
as error recovery, or firmware download in flashless
environments. This only impacts dual functions controllers,
such as 1030. Please apply.
This patch also includes a small cosmetic name change
for mpt_spi_log_info.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When people use the userspace scanning facilities on SAS hardware the
LLDD gets bogus slave_alloc calls. Just fail those gracefully instead
of printing a warning in mptsas and another one in the midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding verbose message returned from firmware
when a task mangment request fails.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:24PM -0700, Moore, Eric wrote:
> Adding MSI support, and command line for enabling
> it. By default, the command line option has MSI disabled.
mpt_msi_enable is initialized to 0 implicitly, no need to do that. Also
replace if (mpt_msi_enable == 1) tests with just if (mpt_msi_enable).
Updated patch below:
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A customer request to send raid asyn actions
from firmware to the event syslog. This shows
when raid volumes go degraded, or complete resync,
or volumes created/deleted, etc.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increasing the reply frame size by 16 bytes, to
be in sync with the other fusion drivers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:13PM -0700, Moore, Eric wrote:
> The task managment request timeout in the eh threads was set
> for U320 timing, which is between 2-5 seconds.
> This is too small for FC and SAS.
> According to the firmware engineers, Fibre needs to be 40 seconds
> and SAS needs to be 10 seconds.
The timeout selection should probably be done in a little helper instead
of duplicated in a few places. Updated patch below.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increase the port enable timeout only for SAS from 30 to 300 seconds.
A customer request for the handling large topologies.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is for spi. This issues bus reset when driver
loads. Handling cases when initator has negotiated for packetized,
and target negotiated for non-packetized; effectly this bus reset
is getting both target and initiator on the same sheet of music.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The prior fusion patches moved an invocation of a function,
mptscsih_TMHandler(), static to mptscsih.c into mptsas.c
Make the function unstatic, move the header to mptscsih.h and export it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fix's problems with recent fc submission regarding
i/o being redirected to the wrong target.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves code intented for SAS from
the generic mptscsih module over to the
mptsas module.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The issuing of the target reset
used in device hot removal case so the
firmware queue is flushed out off outstanding
commands.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
RAID event support.
This will hot add and remove raid volumes
when managment application creates and
deletes the volumes. The driver is basically
responding to firmware asyn events, and reporting
the changes to the above layers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fix is to write 'MPI_HIM_DIM' to the Host Interrupt Mask
register, when enabling interrupts. Instead of the
tilde of MPI_HIM_RIM.
Apparently writing '1's to some of the reserved bits was causing
all the bits to go to `1`, which effectly disabled all interrupts.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This updates mpi headers in fusion drivers to version 1.5.12.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SAS RAID volumes are reported beyond the expected number of phys.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add software recognition for the new LSI Logic Fibre Channel controller.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kashyap, Desai