This change does the following:
* removes the SPI device table in favor of the OF device table
* adds 'name' && 'chip_id' fields to chip_info
* implements chip ID & silicon revision checking; the device ID for
AD7124-4 is 0x0, so just checking that value can be useless;
but at least the silicon revision isn't 0, so a non-zero value can be
used to check that "a" device is on the SPI bus; it's probably the best
way to narrow it down to one of the 2 AD7124 chip IDs
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SADC component in JZ47xx SoCs provides support for touchscreen
operations (pen position and pen down pressure) in single-ended and
differential modes.
The touchscreen component of SADC takes a significant time to stabilize
after first receiving the clock and a delay of 50ms has been empirically
proven to be a safe value before data sampling can begin.
Of the known hardware to use this controller, GCW Zero and Anbernic RG-350
utilize the touchscreen mode by having their joystick(s) attached to the
X/Y positive/negative input pins.
JZ4770 and later SoCs introduce a low-level command feature. With it, up
to 32 commands can be programmed, each one corresponding to a sampling
job. It allows to change the low-voltage reference, the high-voltage
reference, have them connected to VCC, GND, or one of the X-/X+ or Y-/Y+
pins.
This patch introduces support for 6 stream-capable channels:
- channel #0 samples X+/GND
- channel #1 samples Y+/GND
- channel #2 samples X-/GND
- channel #3 samples Y-/GND
- channel #4 samples X+/X-
- channel #5 samples Y+/Y-
Being able to sample X-/GND and Y-/GND is useful on some devices, where
one joystick is connected to the X+/Y+ pins, and a second joystick is
connected to the X-/Y- pins.
All the boards which probe this driver have the interrupt provided from
Device Tree, with no need to handle a case where the IRQ was not provided.
Co-developed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of having one array of struct iio_chan_spec for all SoCs, and
have some SoCs remove the last item of the array as they can't use it,
have each SoC define its array of supported channels.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provide an of_xlate callback in order to retrieve the correct channel
specifier index from the IIO channels array.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce error checks for the clk_enable calls used in this driver.
As part of the changes, move clk_enable/clk_disable calls out of
ingenic_adc_set_config and into respective logic of its callers.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The change is more cosmetic. There is no need to reference this table in
the probe function since 'of_device_get_match_data' is used, which obtains
this information from the driver object.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is the only use of kerneldoc in the source file and no
descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/rockchip_saradc.c:190: warning: Function parameter or member 'reset' not described in 'rockchip_saradc_reset_controller'
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Kerneldoc is only suitable for documenting functions and struct/enums.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_INTERNAL' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_125V' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_INTERNAL_2' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:133: warning: Excess function parameter 'PM8XXX_CHANNEL_MUXOFF' description in 'PM8XXX_CHANNEL_INTERNAL'
drivers/iio/adc/qcom-pm8xxx-xoadc.c:412: warning: Function parameter or member 'variant' not described in 'pm8xxx_xoadc'
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Very few of the struct attributes have been documented here.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'dev' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'palmas' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'irq' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'irq_auto_0' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'irq_auto_1' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'adc_info' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'conv_completion' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup1_data' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup2_data' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup1_enable' not described in 'palmas_gpadc'
drivers/iio/adc/palmas_gpadc.c:114: warning: Function parameter or member 'wakeup2_enable' not described in 'palmas_gpadc'
Cc: Pradeep Goudagunta <pgoudagunta@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No attempt has been made to document any of the demoted structs here.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/max9611.c:117: warning: cannot understand function prototype: 'const unsigned int max9611_mux_conf[][2] = '
drivers/iio/adc/max9611.c:145: warning: cannot understand function prototype: 'const unsigned int max9611_gain_conf[][2] = '
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Kerneldoc expects attributes/parameters to be in '@*.: ' format.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/max1363.c:190: warning: Function parameter or member 'lock' not described in 'max1363_state'
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rohit Sarkar <rohitsarkar5398@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
None of the headers demoted here provide any descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'ato_in' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'atox_in' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'adc_ps_factor_in' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'atox_ps_factor_in' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'ato_out' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'atox_out' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'adc_ps_factor_out' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c💯 warning: Function parameter or member 'atox_ps_factor_out' not described in 'cpcap_adc_ato'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD0' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTP' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_VBUS' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD3' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BPLUS_AD4' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_CHG_ISENSE' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTI' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_USB_ID' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD8' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_AD9' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_LICELL' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_HV_BATTP' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSX1_AD12' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSX2_AD13' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSY1_AD14' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_TSY2_AD15' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTP_PI16' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_BATTI_PI17' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:153: warning: Enum value 'CPCAP_ADC_CHANNEL_NUM' not described in enum 'cpcap_adc_channel'
drivers/iio/adc/cpcap-adc.c:165: warning: Enum value 'CPCAP_ADC_TIMING_IMM' not described in enum 'cpcap_adc_timing'
drivers/iio/adc/cpcap-adc.c:165: warning: Enum value 'CPCAP_ADC_TIMING_IN' not described in enum 'cpcap_adc_timing'
drivers/iio/adc/cpcap-adc.c:165: warning: Enum value 'CPCAP_ADC_TIMING_OUT' not described in enum 'cpcap_adc_timing'
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All lines should start with ' *'.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/at91_adc.c:160: warning: bad line: (Interruptions registers mostly)
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is the only use of function related kerneldoc in the sourcefile
and no descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/ad799x.c:192: warning: Function parameter or member 'irq' not described in 'ad799x_trigger_handler'
drivers/iio/adc/ad799x.c:192: warning: Function parameter or member 'p' not described in 'ad799x_trigger_handler'
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Kerneldoc expects attributes/parameters to be in '@*.: ' format.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/twl6030-gpadc.c:110: warning: Function parameter or member 'ideal' not described in 'twl6030_gpadc_platform_data'
drivers/iio/adc/twl6030-gpadc.c:110: warning: Function parameter or member 'channel_to_reg' not described in 'twl6030_gpadc_platform_data'
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Nishant Kamat <nskamat@ti.com>
Cc: Balaji T K <balajitk@ti.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Girish S Ghongdemath <girishsg@ti.com>
Cc: Ambresh K <ambresh@ti.com>
Cc: Oleksandr Kozaruk <oleksandr.kozaruk@ti.com>
Cc: Mikko Ylinen <mikko.k.ylinen@nokia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/twl4030-madc.c:170: warning: Function parameter or member 'usb3v1' not described in 'twl4030_madc_data'
Also drop a duplicate description of the lock.
Cc: J Keerthy <j-keerthy@ti.com>
Cc: Mikko Ylinen <mikko.k.ylinen@nokia.com>
Cc: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/twl4030-madc.c: In function ‘twl4030_madc_threaded_irq_handler’:
drivers/iio/adc/twl4030-madc.c:475:9: warning: variable ‘len’ set but not used [-Wunused-but-set-variable]
475 | int i, len, ret;
| ^~~
Cc: Sebastian Reichel <sre@kernel.org>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: Mikko Ylinen <mikko.k.ylinen@nokia.com>
Cc: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/ti_am335x_adc.c: In function ‘tiadc_buffer_preenable’:
drivers/iio/adc/ti_am335x_adc.c:297:21: warning: variable ‘read’ set but not used [-Wunused-but-set-variable]
297 | int i, fifo1count, read;
| ^~~~
drivers/iio/adc/ti_am335x_adc.c: In function ‘tiadc_buffer_predisable’:
drivers/iio/adc/ti_am335x_adc.c:346:21: warning: variable ‘read’ set but not used [-Wunused-but-set-variable]
346 | int fifo1count, i, read;
| ^~~~
Cc: Rachna Patil <rachna@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is the only use of function related kerneldoc in the sourcefile
and no descriptions are provided.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/ad7887.c:119: warning: Function parameter or member 'irq' not described in 'ad7887_trigger_handler'
drivers/iio/adc/ad7887.c:119: warning: Function parameter or member 'p' not described in 'ad7887_trigger_handler'
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No attempt has been made to document either of the demoted functions here
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/ad7923.c:159: warning: Function parameter or member 'indio_dev' not described in 'ad7923_update_scan_mode'
drivers/iio/adc/ad7923.c:159: warning: Function parameter or member 'active_scan_mask' not described in 'ad7923_update_scan_mode'
drivers/iio/adc/ad7923.c:202: warning: Function parameter or member 'irq' not described in 'ad7923_trigger_handler'
drivers/iio/adc/ad7923.c:202: warning: Function parameter or member 'p' not described in 'ad7923_trigger_handler'
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No attempt has been made to document either of the demoted functions here.
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/ad7298.c:106: warning: Function parameter or member 'indio_dev' not described in 'ad7298_update_scan_mode'
drivers/iio/adc/ad7298.c:106: warning: Function parameter or member 'active_scan_mask' not described in 'ad7298_update_scan_mode'
drivers/iio/adc/ad7298.c:154: warning: Function parameter or member 'irq' not described in 'ad7298_trigger_handler'
drivers/iio/adc/ad7298.c:154: warning: Function parameter or member 'p' not described in 'ad7298_trigger_handler'
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes the following W=1 kernel build warning(s):
drivers/iio/adc/ad_sigma_delta.c: In function ‘ad_sd_trigger_handler’:
drivers/iio/adc/ad_sigma_delta.c:405:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
405 | int ret;
| ^~~
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into staging-next
We need the staging fixes in here, and it resolves a merge issue with an
iio driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change attaches the life-cycle of the kfifo buffer & IRQ to the
parent-device. This in turn cleans up the exit & error paths, since we
don't need to explicitly cleanup these resources.
The main intent here is to remove the explicit cleanup of the
'indio_dev->buffer' via 'iio_kfifo_free(indio_dev->buffer);'.
As we want to add support for multiple buffers per IIO device, having it
exposed like this makes it tricky to consider a safe backwards compatible
approach for it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change attaches the life-cycle of the channels array to the parent
device object that is attached to the IIO device.
This way we can remove from the cleanup code, the explicit
tiadc_channels_remove() which simply does a kfree() on the channels array.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Whilst it's unlikely this device will ever be instantiated using
ACPI, there is little advantage not assigning the of_device_id table in all
cases and it avoids providing an example that might be coppied into new
drivers.
Also include mod_devicetable.h whilst here as of_device_id is defined
in there so including the header is best practice.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
These stop us using ACPI PRP0001 to instantiate the device.
I am slowly clearly out use of these in IIO to avoid this being coppied
into new drivers.
Here I also included mod_devicetable.h as we are using of_match_id
which is defined in there and hence it is best practice to include
it directly.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Dropping this allows use of ACPI PRP0001.
I'm also looking to drop all of_match_ptr use in IIO in order to avoid
it getting cut and paste into new drivers in the future.
Also add a direct include of mod_devicetable.h to reflect the use
of struct of_device_id.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Allows ACPI PRP0001 to be used with this driver.
Also adds mod_devicetable.h header as the driver is directly using
struct of_device_id which is defined in that file.
I'm also trying to clear out of_match_ptr use in IIO to avoid it
being cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Mårten Lindahl <martenli@axis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
These just prevent the driver being used with ACPI PRP0001.
I am also trying to remove these from IIO in general to avoid
them being coppied into new drivers.
Also include the mod_devicetable.h header as we are using
of_device_id which is defined in there.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Whilst this driver already supports explicit ACPI bindings we
might as well also allow for PRP0001 based binding.
I'm also keen to remove of_match_ptr from IIO drivers to avoid
this (now) anti-pattern getting coppied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Dropping of_match_ptr allows this driver to be used with ACPI.
The header includes are adjusted to include platform_device.h
and mod_devicetable.h instead of OF specific header as nothing
from that header itself is actually used.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
They stop the driver being used with ACPI PRP0001 and are something
I want to avoid being cut and paste into new drivers.
Also switch the include from of.h to mod_devicetable.h as we
struct of_device_id is defined in there and we don't use anything
actually in of.h.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
These just prevent the driver being used with ACPI PRP0001.
They also get cut and paste into new drivers and we want to discourage
this from happening by cleaning it out in general.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Oskar Andero <oskar.andero@gmail.com>
Cc: Søren Andersen <san@rosetechnology.dk>
Cc: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
These just stop the driver being used with ACPI PRP0001 and
we are trying to clear them out of IIO to avoid them getting copied
into new drivers.
Also add the mod_devicetable.h include as we are using
struct of_device_id which is defined in there.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Allows use of driver with ACPI PRP0001 base binding.
Mostly this is about trying to avoid cut and paste of this into new
drivers (it is a frequent review comment) rather than any
thought that this driver might get used on an ACPI platform.
The mod_devicetable.h include is to encourage best practice of including
any header directly used within the code (here for of_match_id)
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This prevents the driver being used with ACPI PRP0001 based
bindings. Also switch include to mod_devicetable.h which devices
the used id structure.
Note this is most about removing something I don't want want cut
and paste into new driver rather than any thought that this particular
driver will be used in an ACPI system (though it might!)
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Part of a slow effort to avoid OF specific code in IIO.
Whilst the main advantages of this are not likely to be seen in this
particular driver (ACPI support via PRP0001) the change proposed
does make things a bit more maintainable and also ensures that
this particular (now) anti-patern is less likely to be cut and
paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
The macro prevents use of driver with ACPI PRP0001 and
the of_match_id structure is defined in mod_devicetable.h so include
that directly rather than of.h.
Note this is mostly about removing something I don't want cut and
paste into new drivers rather than expectation that this particular
driver will be used on an ACPI platform.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
These just prevent the driver being used with ACPI PRP0001
and provide no major benefits.
Part of clearing these out in general in IIO to avoid cut and paste
repetition in new drivers. Also include mod_devicetable.h as we
directly make use of of_device_id which is defined in there.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Allows driver to use ACPI PRP0001 binding and there was no particular
advantage in having the protections in this driver.
Mostly this part of an effort to remove as many OF specific bits
of handling from IIO and use the generic forms where possible.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Allows use of ACPI with PRP0001 and is generally something we are
trying to avoid having people cut and paste into new drivers without
thinking about it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
I guess this is a left over from some earlier cleanup. Not used
currently.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Whilst is unlikely anyone will be using this part with an ACPI PRP0001
based binding any time soon, we are getting a lot of cut and pasting
of this pattern so I am looking to remove it entirely from IIO.
In this case CONFIG_OF protections also removed and
mod_devicetable.h include added given direct use of struct of_device_id.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
We may want to get rid of the iio_priv_to_dev() helper. The reason is that
we will hide some of the members of the iio_dev structure (to prevent
drivers from accessing them directly), and that will also mean hiding the
implementation of the iio_priv_to_dev() helper inside the IIO core.
Hiding the implementation of iio_priv_to_dev() implies that some fast-paths
may not be fast anymore, so a general idea is to try to get rid of the
iio_priv_to_dev() altogether.
The iio_priv() helper won't be affected by the rework, as the iio_dev
struct will keep a reference to the private information.
For this driver, not using iio_priv_to_dev(), means reworking some paths to
pass the iio device and using iio_priv() to access the private information,
and also keeping a reference to the iio device for some quirky paths.
One [quirky] path is the at91_adc_workq_handler() which requires the IIO
device & the state struct to push to buffers.
Since this requires the back-ref to the IIO device, the
at91_adc_touch_pos() also uses it. This simplifies the patch a bit. The
information required in this function is mostly for debugging purposes.
Replacing it with a reference to the IIO device would have been a slightly
bigger change, which may not be worth it (for just the debugging purpose
and given that we need the back-ref to the IIO device anyway).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If 'ad7780_init_gpios()' fails, we must not release some resources that
have not been allocated yet. Return directly instead.
Fixes: 5bb30e7daf ("staging: iio: ad7780: move regulator to after GPIO init")
Fixes: 9085daa4ab ("staging: iio: ad7780: add gain & filter gpio support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When looking for a registered client to attach with, the wrong reference
counters are being grabbed. The idea is to increment the module and device
counters of the client device and not the counters of the axi device being
probed.
Fixes: ef04070692 (iio: adc: adi-axi-adc: add support for AXI ADC IP core)
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jonathan Cameron