On LoPAR "DMA Window Manipulation Calls", it's recommended to remove the
default DMA window for the device, before attempting to configure a DDW,
in order to make the maximum resources available for the next DDW to be
created.
This is a requirement for using DDW on devices in which hypervisor
allows only one DMA window.
If setting up a new DDW fails anywhere after the removal of this
default DMA window, it's needed to restore the default DMA window.
For this, an implementation of ibm,reset-pe-dma-windows rtas call is
needed:
Platforms supporting the DDW option starting with LoPAR level 2.7 implement
ibm,ddw-extensions. The first extension available (index 2) carries the
token for ibm,reset-pe-dma-windows rtas call, which is used to restore
the default DMA window for a device, if it has been deleted.
It does so by resetting the TCE table allocation for the PE to it's
boot time value, available in "ibm,dma-window" device tree node.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200805030455.123024-5-leobras.c@gmail.com
Move the window-removing part of remove_ddw into a new function
(remove_dma_window), so it can be used to remove other DMA windows.
It's useful for removing DMA windows that don't create DIRECT64_PROPNAME
property, like the default DMA window from the device, which uses
"ibm,dma-window".
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200805030455.123024-4-leobras.c@gmail.com
>From LoPAR level 2.8, "ibm,ddw-extensions" index 3 can make the number of
outputs from "ibm,query-pe-dma-windows" go from 5 to 6.
This change of output size is meant to expand the address size of
largest_available_block PE TCE from 32-bit to 64-bit, which ends up
shifting page_size and migration_capable.
This ends up requiring the update of
ddw_query_response->largest_available_block from u32 to u64, and manually
assigning the values from the buffer into this struct, according to
output size.
Also, a routine was created for helping reading the ddw extensions as
suggested by LoPAR: First reading the size of the extension array from
index 0, checking if the property exists, and then returning it's value.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200805030455.123024-3-leobras.c@gmail.com
Create defines to help handling ibm,ddw-applicable values, avoiding
confusion about the index of given operations.
Signed-off-by: Leonardo Bras <leobras.c@gmail.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200805030455.123024-2-leobras.c@gmail.com
Update the CPU to ISA Version Mapping document to include Power10 and
ISA v3.1.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Make sure ISA reference is unique]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200827040556.1783-1-jniethe5@gmail.com
As of commit bdc48fa11e, scripts/checkpatch.pl now has a default line
length warning of 100 characters. The powerpc wrapper script was using
a length of 90 instead of 80 in order to make checkpatch less
restrictive, but now it's making it more restrictive instead.
I think it makes sense to just use the default value now.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200828020542.393022-1-ruscur@russell.cc
The signal handler in the alignment handler self test has the ability
to jump over the instruction that triggered the signal. It does this
by incrementing the PT_NIP in the user context by 4. If it were a
prefixed instruction this will mean that the suffix is then executed
which is incorrect. Instead check if the major opcode indicates a
prefixed instruction (e.g. it is 1) and if so increment PT_NIP by 8.
If ISA v3.1 is not available treat it as a word instruction even if
the major opcode is 1.
Fixes: 620a6473df ("selftests/powerpc: Add prefixed loads/stores to alignment_handler test")
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Fix 32-bit build, rename haveprefixes to prefixes_enabled]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200824131231.14008-1-jniethe5@gmail.com
As of commit 147c05168f ("powerpc/boot: Add support for 64bit little
endian wrapper") the comment in the Makefile is misleading. The wrapper
packaging 64bit kernel may built as a 32 or 64 bit elf. Update the
comment to reflect this.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200825035147.3239-1-jniethe5@gmail.com
The last caller was removed in 2014 in commit fb5a515704 ("powerpc:
Remove platforms/wsp and associated pieces").
As Jordan noticed even though there are no callers, the code above in
fsl_secondary_thread_init() falls through into
generic_secondary_thread_init(). So we can remove the _GLOBAL but not
the body of the function.
However because fsl_secondary_thread_init() is inside #ifdef
CONFIG_PPC_BOOK3E, we can never reach the body of
generic_secondary_thread_init() unless CONFIG_PPC_BOOK3E is enabled,
so we can wrap the whole thing in a single #ifdef.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200819015704.1976364-1-mpe@ellerman.id.au
On older CPUs the switch_endian() syscall doesn't work. Currently that
causes the switch_endian_test to just crash. Instead detect the
failure and properly exit with a failure message.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200819015727.1977134-9-mpe@ellerman.id.au
If we're running on a CPU without VMX/VSX then don't touch them. This
is fragile, the compiler could spill a VMX/VSX register and break the
test anyway. But in practice it seems to work, ie. the test runs to
completion on a system without VSX with this change.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200819015727.1977134-8-mpe@ellerman.id.au
utils.h provides have_hwcap() and have_hwcap2() which check for a
feature bit. Those bits are defined in asm/cputable.h, so include it
in utils.h so users of utils.h don't have to do it manually.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200819015727.1977134-4-mpe@ellerman.id.au
This version of set_dscr() was added for the RFI flush test, and is
fairly specific to it. It also clashes with the version of set_dscr()
in dscr/dscr.h. So move it into the RFI flush test where it's used.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200819015727.1977134-3-mpe@ellerman.id.au
This test creates some threads, which write to TM SPRs, and then makes
sure the registers maintain the correct values across context switches
and contention with other threads.
But currently the test finishes almost instantaneously, which reduces
the chance of it hitting an interesting condition.
So increase the number of loops, so it runs a bit longer, though still
less than 2s on a Power8.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200813013445.686464-3-mpe@ellerman.id.au
This test tries to set affinity to CPUs that don't exist, especially
if the set of online CPUs doesn't start at 0.
But there's no real reason for it to use setaffinity in the first
place, it's just trying to create lots of threads to cause contention.
So drop the setaffinity entirely.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200813013445.686464-2-mpe@ellerman.id.au
Several of the TM tests fail spuriously if CPU 0 is offline, because
they blindly try to affinitise to CPU 0.
Fix them by picking any online CPU and using that instead.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200813013445.686464-1-mpe@ellerman.id.au
These annoy me every time I see them. Why are they here? They're not even
needed for 80cols compliance.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200818044557.135497-1-oohall@gmail.com
Currently, using llvm-objtool, this script just silently succeeds without
actually do the intended checking. So this updates it to work properly.
Firstly, llvm-objdump does not add target symbol names to the end
of branches in its asm output, so we have to drop the branch to
__start_initialization_multiplatform using its address.
Secondly, v9 and 10 specify branch targets as .+<offset>, so we convert
those to actual addresses.
Thirdly, v10 and 11 error out on a vmlinux if given the -R option
complaining that it is "not a dynamic object". The -R does not make
any difference to the asm output, so remove it.
Lastly, v11 produces asm that is very similar to Gnu objtool (at least
as far as branches are concerned), so no further changes are necessary
to make it work.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200812081036.7969-3-sfr@canb.auug.org.au
This is considerably faster then parsing the objdump asm output. It will
also make the enabling of llvm-objdump a little easier.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200812081036.7969-2-sfr@canb.auug.org.au
If we can't find the address of __end_interrupts, then we still exit
successfully as that is the current behaviour.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200811140435.20957-8-sfr@canb.auug.org.au
Also start using sed -E and make all the separate expressions into a
single one with comments. Pull the stripping of condition registers
back into the sed command.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200811140435.20957-5-sfr@canb.auug.org.au
We don't use the raw hex instruction dump, so elide it and adjust the
following expressions.
Also use \s instead of [[:space:]] everywhere.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200811140435.20957-4-sfr@canb.auug.org.au
At memory hot-remove time we can retrieve an LMB's nid from its
corresponding memory_block. There is no need to store the nid
in multiple locations.
Note that lmb_to_memblock() uses find_memory_block() to get the
corresponding memory_block. As find_memory_block() runs in sub-linear
time this approach is negligibly slower than what we do at present.
In exchange for this lookup at hot-remove time we no longer need to
call memory_add_physaddr_to_nid() during drmem_init() for each LMB.
On powerpc, memory_add_physaddr_to_nid() is a linear search, so this
spares us an O(n^2) initialization during boot.
On systems with many LMBs that initialization overhead is palpable and
disruptive. For example, on a box with 249854 LMBs we're seeing
drmem_init() take upwards of 30 seconds to complete:
[ 53.721639] drmem: initializing drmem v2
[ 80.604346] watchdog: BUG: soft lockup - CPU#65 stuck for 23s! [swapper/0:1]
[ 80.604377] Modules linked in:
[ 80.604389] CPU: 65 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc2+ #4
[ 80.604397] NIP: c0000000000a4980 LR: c0000000000a4940 CTR: 0000000000000000
[ 80.604407] REGS: c0002dbff8493830 TRAP: 0901 Not tainted (5.6.0-rc2+)
[ 80.604412] MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE> CR: 44000248 XER: 0000000d
[ 80.604431] CFAR: c0000000000a4a38 IRQMASK: 0
[ 80.604431] GPR00: c0000000000a4940 c0002dbff8493ac0 c000000001904400 c0003cfffffede30
[ 80.604431] GPR04: 0000000000000000 c000000000f4095a 000000000000002f 0000000010000000
[ 80.604431] GPR08: c0000bf7ecdb7fb8 c0000bf7ecc2d3c8 0000000000000008 c00c0002fdfb2001
[ 80.604431] GPR12: 0000000000000000 c00000001e8ec200
[ 80.604477] NIP [c0000000000a4980] hot_add_scn_to_nid+0xa0/0x3e0
[ 80.604486] LR [c0000000000a4940] hot_add_scn_to_nid+0x60/0x3e0
[ 80.604492] Call Trace:
[ 80.604498] [c0002dbff8493ac0] [c0000000000a4940] hot_add_scn_to_nid+0x60/0x3e0 (unreliable)
[ 80.604509] [c0002dbff8493b20] [c000000000087c10] memory_add_physaddr_to_nid+0x20/0x60
[ 80.604521] [c0002dbff8493b40] [c0000000010d4880] drmem_init+0x25c/0x2f0
[ 80.604530] [c0002dbff8493c10] [c000000000010154] do_one_initcall+0x64/0x2c0
[ 80.604540] [c0002dbff8493ce0] [c0000000010c4aa0] kernel_init_freeable+0x2d8/0x3a0
[ 80.604550] [c0002dbff8493db0] [c000000000010824] kernel_init+0x2c/0x148
[ 80.604560] [c0002dbff8493e20] [c00000000000b648] ret_from_kernel_thread+0x5c/0x74
[ 80.604567] Instruction dump:
[ 80.604574] 392918e8 e9490000 e90a000a e92a0000 80ea000c 1d080018 3908ffe8 7d094214
[ 80.604586] 7fa94040 419d00dc e9490010 714a0088 <2faa0008> 409e00ac e9490000 7fbe5040
[ 89.047390] drmem: 249854 LMB(s)
With a patched kernel on the same machine we're no longer seeing the
soft lockup. drmem_init() now completes in negligible time, even when
the LMB count is large.
Fixes: b2d3b5ee66 ("powerpc/pseries: Track LMB nid instead of using device tree")
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200811015115.63677-1-cheloha@linux.ibm.com
Nothing prevents flush_cache_instruction() from being writen in C.
Do it to improve readability and maintainability.
This function is only use by low level callers, it is not
intended to be used by module. Don't export it.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f989eff8296800c427622c0985384148404e4f0b.1597384512.git.christophe.leroy@csgroup.eu
Nothing prevents flush_cache_instruction() from being writen in C.
Do it to improve readability and maintainability.
This function is very small and isn't called from assembly,
make it static inline in asm/cacheflush.h
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/93d93fc69b4b3ad3ceba2fc0756333c0c0245bb7.1597384512.git.christophe.leroy@csgroup.eu
The only callers of flush_instruction_cache() are:
arch/powerpc/kernel/swsusp_booke.S: bl flush_instruction_cache
arch/powerpc/mm/nohash/40x.c: flush_instruction_cache();
arch/powerpc/mm/nohash/44x.c: flush_instruction_cache();
arch/powerpc/mm/nohash/fsl_booke.c: flush_instruction_cache();
arch/powerpc/platforms/44x/machine_check.c: flush_instruction_cache();
arch/powerpc/platforms/44x/machine_check.c: flush_instruction_cache();
This function is not used by book3s/32, drop it.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/50098f49877cea0f46730a9df82dcabf84160e4b.1597384512.git.christophe.leroy@csgroup.eu
The drmem lmb list can have hundreds of thousands of entries, and
unfortunately lookups take the form of linear searches. As long as
this is the case, traversals have the potential to monopolize the CPU
and provoke lockup reports, workqueue stalls, and the like unless
they explicitly yield.
Rather than placing cond_resched() calls within various
for_each_drmem_lmb() loop blocks in the code, put it in the iteration
expression of the loop macro itself so users can't omit it.
Introduce a drmem_lmb_next() iteration helper function which calls
cond_resched() at a regular interval during array traversal. Each
iteration of the loop in DLPAR code paths can involve around ten RTAS
calls which can each take up to 250us, so this ensures the check is
performed at worst every few milliseconds.
Fixes: 6c6ea53725 ("powerpc/mm: Separate ibm, dynamic-memory data from DT format")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200813151131.2070161-1-nathanl@linux.ibm.com
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe
function ("probe_new") can be used instead.
This avoids scanning the identifier tables during probes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200807152713.381588-1-steve@sk2.org
The H_GetPerformanceCounterInfo (GPCI) PHYP hypercall has a subcall,
Affinity_Domain_Info_By_Partition, which returns, among other things,
a "partition affinity score" for a given LPAR. This score, a value on
[0-100], represents the processor-memory affinity for the LPAR in
question. A score of 0 indicates the worst possible affinity while a
score of 100 indicates perfect affinity. The score can be used to
reason about performance.
This patch adds the score for the local LPAR to the lparcfg procfile
under a new 'partition_affinity_score' key.
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200727184605.2945095-2-cheloha@linux.ibm.com
The H_GetPerformanceCounterInfo (GPCI) hypercall input/output structs are
useful to modules outside of perf/, so move them into asm/hvcall.h to live
alongside the other powerpc hypercall structs.
Leave the perf-specific GPCI stuff in perf/hv-gpci.h.
Signed-off-by: Scott Cheloha <cheloha@linux.ibm.com>
Acked-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200727184605.2945095-1-cheloha@linux.ibm.com
Since commit identified below, the forward declaration of
struct irq_chip is useless (was struct hw_interrupt_type at that time)
Remove it, together with the associated comment.
Fixes: c0ad90a32f ("[PATCH] genirq: add ->retrigger() irq op to consolidate hw_irq_resend()")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/fbe58d27cf128d5fe581e4510ded8701858f268e.1596716328.git.christophe.leroy@csgroup.eu
There are spelling mistakes in two debug messages. As recommended
by Wolfram Sang, these can be removed as there is plenty of debug
in the driver core.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200806102901.44988-1-colin.king@canonical.com
Leonardo Bras