This
* makes the queue number passed to drivers a u16
(as it will be with skb_get_queue_mapping)
* removes the useless queue number defines
* splits hw->queues into hw->queues/ampdu_queues
* removes the debugfs files for per-queue counters
* removes some dead QoS code
* removes the beacon queue configuration for IBSS
so that the drivers now never get a queue number
bigger than (hw->queues + hw->ampdu_queues - 1)
for tx and only in the range 0..hw->queues-1 for
conf_tx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the IRQ-disable from mac_suspend.
The main advantage of this is to get rid of the IRQ-sync call in mac_suspend.
We need to remove the MAC suspend bit from the IRQ service mask, as otherwise
the IRQ handler would race with us.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch distributes the Local Oscillator calibration bursts over time,
so that calibration only happens when it's actually needed.
Currently we periodically perform a recalibration of the whole table.
The table is huge and this takes lots of time. Additionally only small bits
of the table are actually needed at a given time. So instead of maintaining
a huge table with all possible calibration values, we create dynamic calibration
settings that
a) We only calibrate when they are actually needed.
b) Are cached for some time until they expire.
So a recalibration might happen if we need a calibration setting that's not
cached, or if the active calibration setting expires.
Currently the expire timeout is set to 30 seconds. We may raise that in future.
This patch reduces overall memory consumption by nuking the
huge static calibration tables.
This patch has been tested on several 4306, 4311 and 4318 flavours.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some TX/RX related locking issues.
With this patch applied, some of the PHY transmission errors are fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes operation of dual-PHY (A/B/G) devices.
Do not anounce the A-PHY to mac80211, as that's not supported, yet.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
tun: Multicast handling in tun_chr_ioctl() needs proper locking.
[NET]: Fix heavy stack usage in seq_file output routines.
[AF_UNIX] Initialise UNIX sockets before general device initcalls
[RTNETLINK]: Fix bogus ASSERT_RTNL warning
iwlwifi: Fix built-in compilation of iwlcore (part 2)
tun: Fix minor race in TUNSETLINK ioctl handling.
ppp_generic: use stats from net_device structure
iwlwifi: Don't unlock priv->mutex if it isn't locked
wireless: rndis_wlan: modparam_workaround_interval is never below 0.
prism54: prism54_get_encode() test below 0 on unsigned index
mac80211: update mesh EID values
b43: Workaround DMA quirks
mac80211: fix use before check of Qdisc length
net/mac80211/rx.c: fix off-by-one
mac80211: Fix race between ieee80211_rx_bss_put and lookup routines.
ath5k: Fix radio identification on AR5424/2424
ssb: Fix all-ones boardflags
b43: Add more btcoexist workarounds
b43: Fix HostFlags data types
b43: Workaround invalid bluetooth settings
...
This adds more workarounds for devices with broken BT bits.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HostFlags are a bitmask of 48bit. So we must use an u64 datatype
to hold all bits.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a workaround for invalid bluetooth SPROM settings
on ASUS PCI cards.
This will stop the microcode from poking with the BT GPIO line.
This fixes data transmission on this device, as the BT GPIO line
is used for something TX related on this device
(probably the power amplifier or the radio).
This also adds a modparam knob to help debugging this in the future,
as more devices with this bug may show up.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After 2.6.24 there was a plan to make the PM core acquire all device
semaphores during a suspend/hibernation to protect itself from
concurrent operations involving device objects. That proved to be
too heavy-handed and we found a better way to achieve the goal, but
before it happened, we had introduced the functions
device_pm_schedule_removal() and destroy_suspended_device() to allow
drivers to "safely" destroy a suspended device and we had adapted some
drivers to use them. Now that these functions are no longer necessary,
it seems reasonable to remove them and modify their users to use the
normal device unregistration instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a fastpath for the common workloads to the
MAC suspend flushing.
In common workloads the FIFO flush will take between 100 and
200 microseconds. So we want to avoid calling msleep() in the
common case, as it will waste over 800 microseconds + scheduler
overhead.
This fastpath will hit in workloads where only small chunks
of data are transmitted (downloading a file) or when a TX rate bigger
or equal to 24MBit/s is used when transmitting lots of stuff (iperf).
So in the commonly used workloads it will basically always hit.
In case the fastpath is not hit, there's no real performance or latency
disadvantage from that.
And yes, I measured this. So this is not one of these
bad Programmer Likeliness Assumptions that are always wrong. ;)
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must use the b43_is_mode() call to check the current interface
operation mode.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the initialization of the PHY TX control words in
shared memory. These control words are used for management frames
like beacons.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes beacon updating in the bottomhalf.
In case the device is busy, we will defer to later in the IRQ handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are some beaconing related fixes. Basically it prevents
the card from triggering the beacon IRQ over and over again.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some timings for pre-TBTT and synthetic PU.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some minor stuff for N-PHY support. Nothing special.
Adds Analog switching and some TODOs for RSSI processing.
Just a patch I had floating around for quite some time now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds PIO support back (D'oh!) for PCMCIA devices.
This is a complete rewrite of the old PIO code. It does actually work
and we get reasonable performance out of it on a modern machine.
On a PowerBook G4 I get a few MBit for TX and a few more for RX.
So it doesn't work as well as DMA (of course), but it's a _lot_ faster
than the old PIO code (only got a few kBit with that).
The limiting factor is the host CPU speed. So it will generate 100%
CPU usage when the network interface is heavily loaded. A voluntary preemption
point in the RX path makes sure Desktop Latency isn't hurt.
PIO is needed for 16bit PCMCIA devices, as we really don't want to poke with
the braindead DMA mechanisms on PCMCIA sockets. Additionally, not all
PCMCIA sockets do actually support DMA in 16bit mode (mine doesn't).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all irqs_disabled() sanity checks, as they are not safe on
a RT-enabled kernel and will trigger bogus warnings.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43_mac_{enable,suspend}() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the DMA ring pointers to have more descriptive and standard
names. Also remove the 6th unused TX ring. We can add it back later,
if we need it. The unused TX-status rx-ring is also removed, as that's
only used by legacy devices not supported by this driver anyway.
This is no functional change, except less memory allocation for
the removed rings.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds QOS support to the b43 driver.
QOS can be disabled on driver level with a module parameter for debugging purposes.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps verify that nothing bad is going on in mac80211,
it is unfortunately not possible to implement this generically
in mac80211 easily because there we can't assume that we only
have a single vif which b43 currently can assume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the high 16 bits of the hostflags.
No functional change.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes bandswitching for the new mac80211 band API.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware version information should always get printed. Not only
on a debug build.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds printk messages with basic information about the driver being loaded.
This information includes a summary of the compiled-in features, which
simplifies bug-reporting and debugging a lot.
Also a firmware ID is printed. This is a unique identifier blob for a specific
version of the firmware. This ID is attached to a specific version of the firmware
blob in b43-fwcutter (see fwcutter git).
This helps users to select the right firmware for their device.
This also makes it possible to use automated scripts to fetch and extract the right
firmware for the driver. (the script will grep the .ko for the "Firmware-ID: xxx" string.
While the driver might still support other versions of the firmware for backward
compatibility, this will always print out the officially supported version, which
people _should_ use.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the b43 driver to avoid deadlocking suspend and resume, which happens
as a result of attempting to unregister device objects locked by the PM core
during suspend/resume cycles. Also, make it use a suspend-safe method of
unregistering device object in the resume error path.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes suspend/resume.
We must not overwrite the MAC addresses on resume. Otherwise
the card won't ACK any packets anymore.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must kill rfkill in any error paths that trigger after rfkill init.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This zeros out all microcode related memory before loading
the microcode.
This also fixes initialization of the MAC control register.
The _only_ place where we overwrite the contents of the MAC control
register is at the beginning of b43_chip_init().
All other places must do read() -> mask/set -> write() to not
overwrite existing bits.
This also adds a longer delay for waiting for the microcode
to initialize itself. It seems that the current timeout is sufficient
on all available devices, but there's no real reason why we shouldn't
wait for up to one second. Slow embedded devices might exist.
Better safe than sorry.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must also store the ID string (filename) for the cached firmware blobs
and verify that we really have the right firmware cached before using it.
If we don't have the right fw cached, we must free it and request the
correct blobs.
This fixes bandswitch on A/B/G multi-PHY devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some code to init the 2055 radio.
This patch adds two files "tables_nphy.h" and "tables_nphy.c"
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for new firmware.
Old firmware is still supported until July 2008.
To get new firmware, go to
ftp://ftp.linksys.com/opensourcecode/wrt150nv11/1.51.3/
and download the tarball. We don't have a smaller tarball, yet.
That will be fixed later.
You can extract firmware out of the "wl_ap.o" file contained
in this tarball using latest fwcutter. You must pass the option
--unsupported to fwcutter.
Fwcutter-010 with official support for a new firmware image will
be released soon.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes reading of the high 16 bits of the radio ID
on new devices. 2055 radios want lo16 to be read first.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the initval filenames for the N-PHY firmware.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the length of the variable section of the beacon instead of the
whole beacon length for bounds checking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This queues frames flagged as "send after DTIM" by mac80211
on the special multicast queue. The firmware will take care
to send the packet after the DTIM.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes uploading of the beacon data and writing of the
TIM and DTIM offsets.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a sparse warning about weird locking.
The spinlock is not needed, so simply remove it.
This also adds some sanity checks to the PHY and radio locking
to protect against recursive locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a new Kconfig option for enabling probing of N-PHYs.
This option will be removed again once the stuff works.
For now it is to help in development. This way real users won't
execute the broken N-PHY codepaths, but the developers can easily
enable N-PHY stuff.
To enable N-PHY probing simply remove the BROKEN dependency
and enable the option in the kernel config.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg