Let's add runtime_suspend and resume functions and atomic enabled
flag. This way we can use these when converting to use cpuidle
for saving and restoring device context.
And we need to maintain the driver state in the driver as documented
in "9. Autosuspend, or automatically-delayed suspends" in the
Documentation/power/runtime_pm.rst document related to using driver
private lock and races with runtime_suspend().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200305082715.15861-3-lokeshvutla@ti.com
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200305082715.15861-2-lokeshvutla@ti.com
Generic clock rate needs to be set in case it was selected as timer clock
source in mchp_pit64b_init_mode(). Otherwise it will be enabled with wrong
rate.
Fixes: 625022a5f1 ("clocksource/drivers/timer-microchip-pit64b: Add Microchip PIT64B support")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1584352376-32585-1-git-send-email-claudiu.beznea@microchip.com
Recently all usages of setup_irq() was replaced by request_irq().
request_irq() does a few sanity checks that were not done in
setup_irq(), if they fail irq registration will fail. One of the check
is to ensure that non-NULL dev_id is passed in the case of shared irq.
Fix it by passing non-NULL dev_id while registering the shared irq.
Fixes: cc2550b421 ("clocksource: Replace setup_irq() by request_irq()")
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200312064817.19000-1-afzal.mohd.ma@gmail.com
Using an arch timer with a frequency of less than 1MHz can potentially
result in incorrect functionality in systems that assume a reasonable
rate of the arch timer of 1 to 50MHz, described as typical in the
architecture specification.
Therefore, warn if the arch timer rate is below 1MHz, which is
considered atypical and worth emphasizing.
Suggested-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
request_irq() is preferred over setup_irq(). The early boot setup_irq()
invocations happen either via 'init_IRQ()' or 'time_init()', while
memory allocators are ready by 'mm_init()'.
Per tglx[1], setup_irq() existed in olden days when allocators were not
ready by the time early interrupts were initialized.
Hence replace setup_irq() by request_irq().
Seldom remove_irq() usage has been observed coupled with setup_irq(),
wherever that has been found, it too has been replaced by free_irq().
A build error that was reported by kbuild test robot <lkp@intel.com>
in the previous version of the patch also has been fixed.
[1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/91961c77c1cf93d41523f5e1ac52043f32f97077.1582799709.git.afzal.mohd.ma@gmail.com
The function omap_dm_timer_of_set_source() was originally added in
commit 31a7448f4f ("ARM: OMAP: dmtimer: Add clock source from DT"),
and is designed to set a clock source from DT using the clocks property
of a timer node. This design choice is okay for clk provider nodes but
otherwise is a bad design as typically the clocks property is used to
specify the functional clocks for a device, and not its parents.
The timer nodes now all define a timer functional clock after the
conversion to ti-sysc and the new clkctrl layout, and this results
in an attempt to set the same functional clock as its parent when a
consumer driver attempts to acquire any of these timers in the
omap_dm_timer_prepare() function. This was masked and worked around
in commit 983a5a43ec ("clocksource: timer-ti-dm: Fix pwm dmtimer
usage of fck reparenting"). Fix all of this by simply dropping the
entire function.
Any DT configuration of clock sources should be achieved using
assigned-clocks and assigned-clock-parents properties provided
by the Common Clock Framework.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200213053504.22638-1-s-anna@ti.com
Write to trigger register(OMAP_TIMER_TRIGGER_REG) will load the value
in Load register(OMAP_TIMER_LOAD_REG) into Counter register
(OMAP_TIMER_COUNTER_REG).
omap_dm_timer_set_load() writes into trigger register every time load
register is updated. When timer is configured in pwm mode, this causes
disruption in current pwm cycle, which is not expected especially when
pwm is used as PPS signal for synchronized PTP clocks. So do not write
into trigger register on updating the period.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200224050753.17784-3-lokeshvutla@ti.com
Check the return from clocksource_mmio_init, add messages in case of
an error and in case of not having a defined clock property.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200219004810.411190-1-matheus@castello.eng.br
OST is the OS Timer, a 64-bit timer/counter with buffered reading.
SoCs before the JZ4770 had (if any) a 32-bit OST; the JZ4770 and
JZ4780 have a 64-bit OST.
This driver will register both a clocksource and a sched_clock to the
system.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200212180408.30872-1-paul@crapouillou.net
The arm_arch_timer requires VDSO_CLOCKMODE_ARCHTIMER to be defined to
compile correctly. On ARM the vDSO can be disabled and when this is the
case the compilation ends prematurely with an error:
$ make ARCH=arm multi_v7_defconfig
$ ./scripts/config -d VDSO
$ make
drivers/clocksource/arm_arch_timer.c:73:44: error:
‘VDSO_CLOCKMODE_ARCHTIMER’ undeclared here (not in a function)
static enum vdso_clock_mode vdso_default = VDSO_CLOCKMODE_ARCHTIMER;
Make the usage of VDSO_CLOCKMODE_ARCHTIMER depend on the VDSO enablement
and initialize the vdso clockmode variable with VDSO_CLOCKMODE_NONE
otherwise.
[ tglx: Match changelog and patch content. ]
Fixes: 5e3c6a312a ("ARM/arm64: vdso: Use common vdso clock mode storage")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200224151552.57274-1-vincenzo.frascino@arm.com
In preparation for supporting the ast2600, pass the shutdown and
interrupt functions to the common init callback.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191107094218.13210-3-joel@jms.id.au
In preparation for supporting the ast2600 which uses a different method
to clear bits in the control register, use a callback for performing the
shutdown sequence.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191107094218.13210-2-joel@jms.id.au
Convert ARM/ARM64 to the generic VDSO clock mode storage. This needs to
happen in one go as they share the clocksource driver.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lkml.kernel.org/r/20200207124403.363235229@linutronix.de
All architectures which use the generic VDSO code have their own storage
for the VDSO clock mode. That's pointless and just requires duplicate code.
X86 abuses the function which retrieves the architecture specific clock
mode storage to mark the clocksource as used in the VDSO. That's silly
because this is invoked on every tick when the VDSO data is updated.
Move this functionality to the clocksource::enable() callback so it gets
invoked once when the clocksource is installed. This allows to make the
clock mode storage generic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com> (Hyper-V parts)
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> (VDSO parts)
Acked-by: Juergen Gross <jgross@suse.com> (Xen parts)
Link: https://lkml.kernel.org/r/20200207124402.934519777@linutronix.de
This is some material that we picked up into our tree late, or that had
more complex dependencies on more than one topic branch that makes sense
to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to better
reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards
-----BEGIN PGP SIGNATURE-----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=R7GU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
- Time namespace support:
If a container migrates from one host to another then it expects that
clocks based on MONOTONIC and BOOTTIME are not subject to
disruption. Due to different boot time and non-suspended runtime these
clocks can differ significantly on two hosts, in the worst case time
goes backwards which is a violation of the POSIX requirements.
The time namespace addresses this problem. It allows to set offsets for
clock MONOTONIC and BOOTTIME once after creation and before tasks are
associated with the namespace. These offsets are taken into account by
timers and timekeeping including the VDSO.
Offsets for wall clock based clocks (REALTIME/TAI) are not provided by
this mechanism. While in theory possible, the overhead and code
complexity would be immense and not justified by the esoteric potential
use cases which were discussed at Plumbers '18.
The overhead for tasks in the root namespace (host time offsets = 0) is
in the noise and great effort was made to ensure that especially in the
VDSO. If time namespace is disabled in the kernel configuration the
code is compiled out.
Kudos to Andrei Vagin and Dmitry Sofanov who implemented this feature
and kept on for more than a year addressing review comments, finding
better solutions. A pleasant experience.
- Overhaul of the alarmtimer device dependency handling to ensure that
the init/suspend/resume ordering is correct.
- A new clocksource/event driver for Microchip PIT64
- Suspend/resume support for the Hyper-V clocksource
- The usual pile of fixes, updates and improvements mostly in the
driver code.
-----BEGIN PGP SIGNATURE-----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=x3qT
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The timekeeping and timers departement provides:
- Time namespace support:
If a container migrates from one host to another then it expects
that clocks based on MONOTONIC and BOOTTIME are not subject to
disruption. Due to different boot time and non-suspended runtime
these clocks can differ significantly on two hosts, in the worst
case time goes backwards which is a violation of the POSIX
requirements.
The time namespace addresses this problem. It allows to set offsets
for clock MONOTONIC and BOOTTIME once after creation and before
tasks are associated with the namespace. These offsets are taken
into account by timers and timekeeping including the VDSO.
Offsets for wall clock based clocks (REALTIME/TAI) are not provided
by this mechanism. While in theory possible, the overhead and code
complexity would be immense and not justified by the esoteric
potential use cases which were discussed at Plumbers '18.
The overhead for tasks in the root namespace (ie where host time
offsets = 0) is in the noise and great effort was made to ensure
that especially in the VDSO. If time namespace is disabled in the
kernel configuration the code is compiled out.
Kudos to Andrei Vagin and Dmitry Sofanov who implemented this
feature and kept on for more than a year addressing review
comments, finding better solutions. A pleasant experience.
- Overhaul of the alarmtimer device dependency handling to ensure
that the init/suspend/resume ordering is correct.
- A new clocksource/event driver for Microchip PIT64
- Suspend/resume support for the Hyper-V clocksource
- The usual pile of fixes, updates and improvements mostly in the
driver code"
* tag 'timers-core-2020-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
alarmtimer: Make alarmtimer_get_rtcdev() a stub when CONFIG_RTC_CLASS=n
alarmtimer: Use wakeup source from alarmtimer platform device
alarmtimer: Make alarmtimer platform device child of RTC device
alarmtimer: Update alarmtimer_get_rtcdev() docs to reflect reality
hrtimer: Add missing sparse annotation for __run_timer()
lib/vdso: Only read hrtimer_res when needed in __cvdso_clock_getres()
MIPS: vdso: Define BUILD_VDSO32 when building a 32bit kernel
clocksource/drivers/hyper-v: Set TSC clocksource as default w/ InvariantTSC
clocksource/drivers/hyper-v: Untangle stimers and timesync from clocksources
clocksource/drivers/timer-microchip-pit64b: Fix sparse warning
clocksource/drivers/exynos_mct: Rename Exynos to lowercase
clocksource/drivers/timer-ti-dm: Fix uninitialized pointer access
clocksource/drivers/timer-ti-dm: Switch to platform_get_irq
clocksource/drivers/timer-ti-dm: Convert to devm_platform_ioremap_resource
clocksource/drivers/em_sti: Fix variable declaration in em_sti_probe
clocksource/drivers/em_sti: Convert to devm_platform_ioremap_resource
clocksource/drivers/bcm2835_timer: Fix memory leak of timer
clocksource/drivers/cadence-ttc: Use ttc driver as platform driver
clocksource/drivers/timer-microchip-pit64b: Add Microchip PIT64B support
clocksource/drivers/hyper-v: Reserve PAGE_SIZE space for tsc page
...
Change the Hyper-V clocksource ratings to 250, below the TSC clocksource
rating of 300. In configurations where Hyper-V offers an InvariantTSC,
the TSC is not marked "unstable", so the TSC clocksource is available
and preferred. With the higher rating, it will be the default. On
older hardware and Hyper-V versions, the TSC is marked "unstable", so no
TSC clocksource is created and the selected Hyper-V clocksource will be
the default.
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200109160650.16150-3-parri.andrea@gmail.com
hyperv_timer.c exports hyperv_cs, which is used by stimers and the
timesync mechanism. However, the clocksource dependency is not
needed: these mechanisms only depend on the partition reference
counter (which can be read via a MSR or via the TSC Reference Page).
Introduce the (function) pointer hv_read_reference_counter, as an
embodiment of the partition reference counter read, and export it
in place of the hyperv_cs pointer. The latter can be removed.
This should clarify that there's no relationship between Hyper-V
stimers & timesync and the Linux clocksource abstractions. No
functional or semantic change.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200109160650.16150-2-parri.andrea@gmail.com
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200104152107.11407-12-krzk@kernel.org
Clean-up commit 8c82723414d5 ("clocksource/drivers/timer-ti-dm: Switch to
platform_get_irq") caused a regression where we now try to access
uninitialized data for timer:
drivers/clocksource/timer-ti-dm.c: In function 'omap_dm_timer_probe':
drivers/clocksource/timer-ti-dm.c:798:13: warning: 'timer' may be used
uninitialized in this function [-Wmaybe-uninitialized]
On boot we now get:
Unable to handle kernel NULL pointer dereference at virtual address
00000004
...
(omap_dm_timer_probe) from [<c061ac7c>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c0618c04>] (really_probe+0x1dc/0x348)
(really_probe) from [<c0618ef4>] (driver_probe_device+0x5c/0x160)
Let's fix the issue by moving platform_get_irq to happen after timer has
been allocated.
Fixes: bc83caddf1 ("clocksource/drivers/timer-ti-dm: Switch to platform_get_irq")
Cc: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200106203700.21009-1-tony@atomide.com
platform_get_resource(pdev, IORESOURCE_IRQ) is not recommended for
requesting IRQ's resources, as they can be not ready yet. Using
platform_get_irq() instead is preferred for getting IRQ even if it
was not retrieved earlier.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191221173027.30716-5-tiny.windzz@gmail.com
Use devm_platform_ioremap_resource() to simplify code, which
wraps 'platform_get_resource' and 'devm_ioremap_resource' in a
single helper.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191221173027.30716-4-tiny.windzz@gmail.com
Use devm_platform_ioremap_resource() to simplify code, which
wraps 'platform_get_resource' and 'devm_ioremap_resource' in a
single helper.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191221173027.30716-2-tiny.windzz@gmail.com
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f0898 ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Currently TTC driver is TIMER_OF_DECLARE type driver. Because of
that, TTC driver may be initialized before other clock drivers. If
TTC driver is dependent on that clock driver then initialization of
TTC driver will failed.
So use TTC driver as platform driver instead of using
TIMER_OF_DECLARE.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1573122988-18399-1-git-send-email-rajan.vaja@xilinx.com
Add driver for Microchip PIT64B timer. Timer could be used in continuous
mode or oneshot mode. The hardware has 2x32 bit registers for period
emulating a 64 bit timer. The LSB_PR and MSB_PR registers are used to
set the period value (compare value). TLSB and TMSB keeps the current
value of the counter. After a compare the TLSB and TMSB register resets.
The driver uses PIT64B timer for clocksource or clockevent. First
requested timer would be registered as clockevent, second one would be
registered as clocksource. Individual PIT64B hardware resources were
used for clocksource and clockevent to be able to support high resolution
timers with this hardware implementation.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1576235962-30123-3-git-send-email-claudiu.beznea@microchip.com
Currently, the reserved size for a tsc page is 4K, which is enough for
communicating with hypervisor. However, in the case where we want to
export the tsc page to userspace (e.g. for vDSO to read the
clocksource), the tsc page should be at least PAGE_SIZE, otherwise, when
PAGE_SIZE is larger than 4K, extra kernel data will be mapped into
userspace, which means leaking kernel information.
Therefore reserve PAGE_SIZE space for tsc_pg as a preparation for the
vDSO support of ARM64 in the future. Also, while at it, replace all
reference to tsc_pg with hv_get_tsc_page() since it should be the only
interface to access tsc page.
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Cc: linux-hyperv@vger.kernel.org
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191126021723.4710-1-boqun.feng@gmail.com
Fix lots of typo, spelling, punctuation, and grammar miscues in
drivers/clocksource/Kconfig.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/4deb42a9-82f2-72f9-891f-972a9a399f4f@infradead.org
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191120134236.15959-1-krzk@kernel.org
This is needed for hibernation, e.g. when we resume the old kernel, we need
to disable the "current" kernel's TSC page and then resume the old kernel's.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1574233946-48377-1-git-send-email-decui@microsoft.com
The DM365 platform has a strange quirk (only present when using ancient
u-boot - mainline u-boot v2013.01 and later works fine) where if we
enable the second half of the timer in periodic mode before we do its
initialization - the time won't start flowing and we can't boot.
When using more recent u-boot, we can enable the timer, then reinitialize
it and all works fine.
To work around this issue only enable clockevents once tim34 is
initialized i.e. move clockevents_config_and_register() below tim34
initialization.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Pull timer updates from Ingo Molnar:
"The main changes in the timer code in this cycle were:
- Clockevent updates:
- timer-of framework cleanups. (Geert Uytterhoeven)
- Use timer-of for the renesas-ostm and the device name to prevent
name collision in case of multiple timers. (Geert Uytterhoeven)
- Check if there is an error after calling of_clk_get in asm9260
(Chuhong Yuan)
- ABI fix: Zero out high order bits of nanoseconds on compat
syscalls. This got broken a year ago, with apparently no side
effects so far.
Since the kernel would use random data otherwise I don't think we'd
have other options but to fix the bug, even if there was a side
effect to applications (Dmitry Safonov)
- Optimize ns_to_timespec64() on 32-bit systems: move away from
div_s64_rem() which can be slow, to div_u64_rem() which is faster
(Arnd Bergmann)
- Annotate KCSAN-reported false positive data races in
hrtimer_is_queued() users by moving timer->state handling over to
the READ_ONCE()/WRITE_ONCE() APIs. This documents these accesses
(Eric Dumazet)
- Misc cleanups and small fixes"
[ I undid the "ABI fix" and updated the comments instead. The reason
there were apparently no side effects is that the fix was a no-op.
The updated comment is to say _why_ it was a no-op. - Linus ]
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Zero the upper 32-bits in __kernel_timespec on 32-bit
time: Rename tsk->real_start_time to ->start_boottime
hrtimer: Remove the comment about not used HRTIMER_SOFTIRQ
time: Fix spelling mistake in comment
time: Optimize ns_to_timespec64()
hrtimer: Annotate lockless access to timer->state
clocksource/drivers/asm9260: Add a check for of_clk_get
clocksource/drivers/renesas-ostm: Use unique device name instead of ostm
clocksource/drivers/renesas-ostm: Convert to timer_of
clocksource/drivers/timer-of: Use unique device name instead of timer
clocksource/drivers/timer-of: Convert last full_name to %pOF
New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv
-----BEGIN PGP SIGNATURE-----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=nbwY
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"New features:
- SECCOMP support
- nommu support
- SBI-less system support
- M-Mode support
- TLB flush optimizations
Other improvements:
- Pass the complete RISC-V ISA string supported by the CPU cores to
userspace, rather than redacting parts of it in the kernel
- Add platform DMA IP block data to the HiFive Unleashed board DT
file
- Add Makefile support for BZ2, LZ4, LZMA, LZO kernel image
compression formats, in line with other architectures
Cleanups:
- Remove unnecessary PTE_PARENT_SIZE macro
- Standardize include guard naming across arch/riscv"
* tag 'riscv/for-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (22 commits)
riscv: provide a flat image loader
riscv: add nommu support
riscv: clear the instruction cache and all registers when booting
riscv: read the hart ID from mhartid on boot
riscv: provide native clint access for M-mode
riscv: dts: add support for PDMA device of HiFive Unleashed Rev A00
riscv: add support for MMIO access to the timer registers
riscv: implement remote sfence.i using IPIs
riscv: cleanup the default power off implementation
riscv: poison SBI calls for M-mode
riscv: don't allow selecting SBI based drivers for M-mode
RISC-V: Add multiple compression image format.
riscv: clean up the macro format in each header file
riscv: Use PMD_SIZE to replace PTE_PARENT_SIZE
riscv: abstract out CSR names for supervisor vs machine mode
riscv: separate MMIO functions into their own header file
riscv: enter WFI in default_power_off() if SBI does not shutdown
RISC-V: Issue a tlb page flush if possible
RISC-V: Issue a local tlbflush if possible.
RISC-V: Do not invoke SBI call if cpumask is empty
...
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
Pull x86 hyperv updates from Ingo Molnar:
"Misc updates to the hyperv guest code:
- Rework clockevents initialization to better support hibernation
- Allow guests to enable InvariantTSC
- Micro-optimize send_ipi_one"
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyperv: Initialize clockevents earlier in CPU onlining
x86/hyperv: Allow guests to enable InvariantTSC
x86/hyperv: Micro-optimize send_ipi_one()
-----BEGIN PGP SIGNATURE-----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=QCEy
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow to print symbolic error names via new %pe modifier.
- Use pr_warn() instead of the remaining pr_warning() calls. Fix
formatting of the related lines.
- Add VSPRINTF entry to MAINTAINERS.
* tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits)
checkpatch: don't warn about new vsprintf pointer extension '%pe'
MAINTAINERS: Add VSPRINTF
tools lib api: Renaming pr_warning to pr_warn
ASoC: samsung: Use pr_warn instead of pr_warning
lib: cpu_rmap: Use pr_warn instead of pr_warning
trace: Use pr_warn instead of pr_warning
dma-debug: Use pr_warn instead of pr_warning
vgacon: Use pr_warn instead of pr_warning
fs: afs: Use pr_warn instead of pr_warning
sh/intc: Use pr_warn instead of pr_warning
scsi: Use pr_warn instead of pr_warning
platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning
platform/x86: asus-laptop: Use pr_warn instead of pr_warning
platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning
oprofile: Use pr_warn instead of pr_warning
of: Use pr_warn instead of pr_warning
macintosh: Use pr_warn instead of pr_warning
idsn: Use pr_warn instead of pr_warning
ide: Use pr_warn instead of pr_warning
crypto: n2: Use pr_warn instead of pr_warning
...
Hyper-V has historically initialized stimer-based clockevents late in the
process of onlining a CPU because clockevents depend on stimer
interrupts. In the original Hyper-V design, stimer interrupts generate a
VMbus message, so the VMbus machinery must be running first, and VMbus
can't be initialized until relatively late. On x86/64, LAPIC timer based
clockevents are used during early initialization before VMbus and
stimer-based clockevents are ready, and again during CPU offlining after
the stimer clockevents have been shut down.
Unfortunately, this design creates problems when offlining CPUs for
hibernation or other purposes. stimer-based clockevents are shut down
relatively early in the offlining process, so clockevents_unbind_device()
must be used to fallback to the LAPIC-based clockevents for the remainder
of the offlining process. Furthermore, the late initialization and early
shutdown of stimer-based clockevents doesn't work well on ARM64 since there
is no other timer like the LAPIC to fallback to. So CPU onlining and
offlining doesn't work properly.
Fix this by recognizing that stimer Direct Mode is the normal path for
newer versions of Hyper-V on x86/64, and the only path on other
architectures. With stimer Direct Mode, stimer interrupts don't require any
VMbus machinery. stimer clockevents can be initialized and shut down
consistent with how it is done for other clockevent devices. While the old
VMbus-based stimer interrupts must still be supported for backward
compatibility on x86, that mode of operation can be treated as legacy.
So add a new Hyper-V stimer entry in the CPU hotplug state list, and use
that new state when in Direct Mode. Update the Hyper-V clocksource driver
to allocate and initialize stimer clockevents earlier during boot. Update
Hyper-V initialization and the VMbus driver to use this new design. As a
result, the LAPIC timer is no longer used during boot or CPU
onlining/offlining and clockevents_unbind_device() is not called. But
retain the old design as a legacy implementation for older versions of
Hyper-V that don't support Direct Mode.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lkml.kernel.org/r/1573607467-9456-1-git-send-email-mikelley@microsoft.com
When running in M-mode we can't use the SBI to set the timer, and
don't have access to the time CSR as that usually is emulated by
M-mode. Instead provide code that directly accesses the MMIO for
the timer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de> # for drivers/clocksource
[paul.walmsley@sifive.com: updated to apply; fixed checkpatch
issue; timex.h now includes asm/mmio.h to resolve header file
problems]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Many of the privileged CSRs exist in a supervisor and machine version
that are used very similarly. Provide versions of the CSR names and
fields that map to either the S-mode or M-mode variant depending on
a new CONFIG_RISCV_M_MODE kconfig symbol.
Contains contributions from Damien Le Moal <Damien.LeMoal@wdc.com>
and Paul Walmsley <paul.walmsley@sifive.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de> # for drivers/clocksource, drivers/irqchip
[paul.walmsley@sifive.com: updated to apply]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
(Geert Uytterhoeven)
- Use timer-of for the renesas-ostm and the device name to prevent
name collision in case of multiple timers (Geert Uytterhoeven)
- Check if there is an error after calling of_clk_get in asm9260
(Chuhong Yuan)
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRuKdf4M92Gi9vqihve5qtOL396pgUCXb/z1wAKCRDe5qtOL396
pot/AQCodxfvuLKrIlIuj67XDJ6zSdDgSvDy2AIWqfmvsd/26wD9EtkofyKiPpyX
L6B+UmavGyo4VHCJphQza63NdQPK7wc=
=9C23
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.6' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clockevent updates from Daniel Lezcano:
- Some cleanups for the timer-of, use %p0F and the unique device name
(Geert Uytterhoeven)
- Use timer-of for the renesas-ostm and the device name to prevent
name collision in case of multiple timers (Geert Uytterhoeven)
- Check if there is an error after calling of_clk_get in asm9260
(Chuhong Yuan)
function (Geert Uytterhoeven)
- Fix double free when using timer-of in the mediatek timer driver
(Fabien Parent)
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRuKdf4M92Gi9vqihve5qtOL396pgUCXcA60wAKCRDe5qtOL396
pkSvAQDLwVUlqqObVfctzKDoElTniN4IQgYUrURCqAN4tIdUkwD9GlYHPrD0MC+j
hph2uxc652cDv86n8cvMlplZWKNqSAs=
=2nKq
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.4-rc6' of https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevent fixes from Daniel Lezcano:
- Fix scary messages in sh_mtu2 by using platform_irq_count() helper
function (Geert Uytterhoeven)
- Fix double free when using timer-of in the mediatek timer driver
(Fabien Parent)
asm9260_timer_init misses a check for of_clk_get.
Add a check for it and print errors like other clocksource drivers.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016124330.22211-1-hslester96@gmail.com
Currently all OSTM devices are called "ostm", also in kernel messages.
As there can be multiple instances in an SoC, this can confuse the user.
Hence construct a unique name from the DT node name, like is done for
platform devices.
On RSK+RZA1, the boot log changes like:
-clocksource: ostm: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 57352151442 ns
+clocksource: timer@fcfec000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 57352151442 ns
sched_clock: 32 bits at 33MHz, resolution 30ns, wraps every 64440619504ns
-ostm: used for clocksource
-ostm: used for clock events
+/soc/timer@fcfec000: used for clocksource
+/soc/timer@fcfec400: used for clock events
...
-clocksource: Switched to clocksource ostm
+clocksource: Switched to clocksource timer@fcfec000
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016144747.29538-5-geert+renesas@glider.be
Convert the Renesas OSTM driver to use the timer_of framework.
This reduces the driver object size by 367 bytes (with gcc 7.4.0).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016144747.29538-4-geert+renesas@glider.be
If a hardware-specific driver does not provide a name, the timer-of core
falls back to device_node.name. Due to generic DT node naming policies,
that name is almost always "timer", and thus doesn't identify the actual
timer used.
Fix this by using device_node.full_name instead, which includes the unit
addrees.
Example impact on /proc/timer_list:
-Clock Event Device: timer
+Clock Event Device: timer@fcfec400
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016144747.29538-3-geert+renesas@glider.be
Commit 469869d18a ("clocksource: Convert to using %pOF instead of
full_name") converted all but the one just added before by commit
32f2fea6e7 ("clocksource/drivers/timer-of: Handle
of_irq_get_byname() result correctly").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016144747.29538-2-geert+renesas@glider.be
As said in commit f2c2cbcc35 ("powerpc: Use pr_warn instead of
pr_warning"), removing pr_warning so all logging messages use a
consistent <prefix>_warn style. Let's do it.
Link: http://lkml.kernel.org/r/20191018031850.48498-11-wangkefeng.wang@huawei.com
To: linux-kernel@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
[pmladek@suse.com: Fixed indentation]
Signed-off-by: Petr Mladek <pmladek@suse.com>
As platform_get_irq_by_name() now prints an error when the interrupt
does not exist, looping over possibly non-existing interrupts causes the
printing of scary messages like:
sh_mtu2 fcff0000.timer: IRQ tgi1a not found
sh_mtu2 fcff0000.timer: IRQ tgi2a not found
Fix this by using the platform_irq_count() helper, to avoid touching
non-existent interrupts. Limit the returned number of interrupts to the
maximum number of channels currently supported by the driver in a
future-proof way, i.e. using ARRAY_SIZE() instead of a hardcoded number.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191016143003.28561-1-geert+renesas@glider.be
Old early platform device support is now sh-specific. Before moving on
to implementing new early platform framework based on real platform
devices, prefix all early platform symbols with 'sh_'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperH is the only user of the current implementation of early platform
device support. We want to introduce a more robust approach to early
probing. As the first step - move all the current early platform code
to arch/sh.
In order not to export internal drivers/base functions to arch code for
this temporary solution - copy the two needed routines for driver
matching from drivers/base/platform.c to arch/sh/drivers/platform_early.c.
Also: call early_platform_cleanup() from subsys_initcall() so that it's
called after all early devices are probed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap reports on the sparse list that sparse warns about this
expression:
of_irq->percpu ? free_percpu_irq(of_irq->irq, clkevt) :
free_irq(of_irq->irq, clkevt);
and honestly, sparse is correct to warn. The return type of
free_percpu_irq() is 'void', while free_irq() returns a 'const void *'
that is the devname argument passed in to the request_irq().
You can't mix a void type with a non-void types in a conditional
expression according to the C standard. It so happens that gcc seems to
accept it - and the resulting type of the expression is void - but
there's really no reason for the kernel to have this kind of
non-standard expression with no real upside.
The natural way to write that expression is with an if-statement:
if (of_irq->percpu)
free_percpu_irq(of_irq->irq, clkevt);
else
free_irq(of_irq->irq, clkevt);
which is more legible anyway.
I'm not sure why that timer-of code seems to have this odd pattern. It
does the same at allocation time, but at least there the types match,
and it makes sense as an expression.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
Pull core timer updates from Thomas Gleixner:
"Timers and timekeeping updates:
- A large overhaul of the posix CPU timer code which is a preparation
for moving the CPU timer expiry out into task work so it can be
properly accounted on the task/process.
An update to the bogus permission checks will come later during the
merge window as feedback was not complete before heading of for
travel.
- Switch the timerqueue code to use cached rbtrees and get rid of the
homebrewn caching of the leftmost node.
- Consolidate hrtimer_init() + hrtimer_init_sleeper() calls into a
single function
- Implement the separation of hrtimers to be forced to expire in hard
interrupt context even when PREEMPT_RT is enabled and mark the
affected timers accordingly.
- Implement a mechanism for hrtimers and the timer wheel to protect
RT against priority inversion and live lock issues when a (hr)timer
which should be canceled is currently executing the callback.
Instead of infinitely spinning, the task which tries to cancel the
timer blocks on a per cpu base expiry lock which is held and
released by the (hr)timer expiry code.
- Enable the Hyper-V TSC page based sched_clock for Hyper-V guests
resulting in faster access to timekeeping functions.
- Updates to various clocksource/clockevent drivers and their device
tree bindings.
- The usual small improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (101 commits)
posix-cpu-timers: Fix permission check regression
posix-cpu-timers: Always clear head pointer on dequeue
hrtimer: Add a missing bracket and hide `migration_base' on !SMP
posix-cpu-timers: Make expiry_active check actually work correctly
posix-timers: Unbreak CONFIG_POSIX_TIMERS=n build
tick: Mark sched_timer to expire in hard interrupt context
hrtimer: Add kernel doc annotation for HRTIMER_MODE_HARD
x86/hyperv: Hide pv_ops access for CONFIG_PARAVIRT=n
posix-cpu-timers: Utilize timerqueue for storage
posix-cpu-timers: Move state tracking to struct posix_cputimers
posix-cpu-timers: Deduplicate rlimit handling
posix-cpu-timers: Remove pointless comparisons
posix-cpu-timers: Get rid of 64bit divisions
posix-cpu-timers: Consolidate timer expiry further
posix-cpu-timers: Get rid of zero checks
rlimit: Rewrite non-sensical RLIMIT_CPU comment
posix-cpu-timers: Respect INFINITY for hard RTTIME limit
posix-cpu-timers: Switch thread group sampling to array
posix-cpu-timers: Restructure expiry array
posix-cpu-timers: Remove cputime_expires
...
If we just use the CSRs that these map to directly the code is simpler
and doesn't require extra inline assembly code. Also fix up the top-level
comment in timer-riscv.c to not talk about the cycle count or mention
details of the clocksource interface, of which this file is just a
consumer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Update the CMT driver to mark "renesas,cmt-48" as deprecated.
Instead of documenting a theoretical hardware device based on current software
support level, define DT bindings top-down based on available data sheet
information and make use of part numbers in the DT compat string.
In case of the only in-tree users r8a7740 and sh73a0 the compat strings
"renesas,r8a7740-cmt1" and "renesas,sh73a0-cmt1" may be used instead.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add SoC-specific matching for CMT1 on r8a7740 and sh73a0.
This allows us to move away from the old DT bindings such as
- "renesas,cmt-48-sh73a0"
- "renesas,cmt-48-r8a7740"
- "renesas,cmt-48"
in favour for the now commonly used format "renesas,<soc>-<device>"
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Deferred probe is an expected return value on many platforms and so
there's no need to output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Deferred probe is an expected return value for clk_get() on many
platforms. The driver deals with it properly, so there's no need
to output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
NPCM7XX_Tx_OPER GENMASK bits are wrong, fix them.
Hopefully the NPCM7XX_REG_TICR0 register reset value of those bits was 0,
so it did not cause an issue.
The function npcm7xx_timer_oneshot() reads the register
NPCM7XX_REG_TCSR0, modifies it and then reads it again overwriting the
previous changes. Remove the extra read which is pointless.
The function npcm7xx_timer_periodic() is correct but the code writes
to the NPCM7XX_REG_TICR0 register while it is dealing with the
NPCM7XX_REG_TCSR0 register, that is confusing. Separate the write to
the registers in the code for the sake of clarity.
Fixes: 1c00289ecd ("clocksource/drivers/npcm: Add NPCM7xx timer driver")
Signed-off-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use the DIV_ROUND_CLOSEST() helper instead of open-coding the same
operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The system counter block guide states that the base clock is
internally divided by 3 before use, that means the clock input of
system counter defined in DT should be base clock which is normally
from OSC, and then internally divided by 3 before use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Implement and register delay timer to allow get_cycles() to work properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Newer Allwinner SoCs have different number of interrupts, let's add
different compatibles for all of them to deal with this properly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
There is no particular reason to not enable TSC page clocksource on
32-bit. mul_u64_u64_shr() is available and despite the increased
computational complexity (compared to 64bit) TSC page is still a huge win
compared to MSR-based clocksource.
In-kernel reads:
MSR based clocksource: 3361 cycles
TSC page clocksource: 49 cycles
Reads from userspace (utilizing vDSO in case of TSC page):
MSR based clocksource: 5664 cycles
TSC page clocksource: 131 cycles
Enabling TSC page on 32bits allows to get rid of CONFIG_HYPERV_TSCPAGE as
it is now not any different from CONFIG_HYPERV_TIMER.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lkml.kernel.org/r/20190822083630.17059-1-vkuznets@redhat.com
Hyper-V guests use the default native_sched_clock() in
pv_ops.time.sched_clock on x86. But native_sched_clock() directly uses the
raw TSC value, which can be discontinuous in a Hyper-V VM.
Add the generic hv_setup_sched_clock() to set the sched clock function
appropriately. On x86, this sets pv_ops.time.sched_clock to read the
Hyper-V reference TSC value that is scaled and adjusted to be continuous.
Also move the Hyper-V reference TSC initialization much earlier in the boot
process so no discontinuity is observed when pv_ops.time.sched_clock
calculates its offset.
[ tglx: Folded build fix ]
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lkml.kernel.org/r/20190814123216.32245-3-Tianyu.Lan@microsoft.com
Prepare to add Hyper-V sched clock callback and move Hyper-V Reference TSC
initialization much earlier in the boot process. Earlier initialization is
needed so that it happens while the timestamp value is still 0 and no
discontinuity in the timestamp will occur when pv_ops.time.sched_clock
calculates its offset.
The earlier initialization requires that the Hyper-V TSC page be allocated
statically instead of with vmalloc(), so fixup the references to the TSC
page and the method of getting its physical address.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20190814123216.32245-2-Tianyu.Lan@microsoft.com
This driver handles the TCU (Timer Counter Unit) present on the Ingenic
JZ47xx SoCs, and provides the kernel with a system timer, a clocksource
and a sched_clock.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: od@zcrc.me
There is only one clocksource in RISC-V. The boot cpu initializes
that clocksource. No need to keep a percpu data structure.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Hyper-V clock/timer code and data structures are currently mixed
in with other code in the ISA independent drivers/hv directory as
well as the ISA dependent Hyper-V code under arch/x86.
Consolidate this code and data structures into a Hyper-V clocksource driver
to better follow the Linux model. In doing so, separate out the ISA
dependent portions so the new clocksource driver works for x86 and for the
in-process Hyper-V on ARM64 code.
To start, move the existing clockevents code to create the new clocksource
driver. Update the VMbus driver to call initialization and cleanup routines
since the Hyper-V synthetic timers are not independently enumerated in
ACPI.
No behavior is changed and no new functionality is added.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "bp@alien8.de" <bp@alien8.de>
Cc: "will.deacon@arm.com" <will.deacon@arm.com>
Cc: "catalin.marinas@arm.com" <catalin.marinas@arm.com>
Cc: "mark.rutland@arm.com" <mark.rutland@arm.com>
Cc: "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "linux-hyperv@vger.kernel.org" <linux-hyperv@vger.kernel.org>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: Sunil Muthuswamy <sunilmut@microsoft.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: "sashal@kernel.org" <sashal@kernel.org>
Cc: "vincenzo.frascino@arm.com" <vincenzo.frascino@arm.com>
Cc: "linux-arch@vger.kernel.org" <linux-arch@vger.kernel.org>
Cc: "linux-mips@vger.kernel.org" <linux-mips@vger.kernel.org>
Cc: "linux-kselftest@vger.kernel.org" <linux-kselftest@vger.kernel.org>
Cc: "arnd@arndb.de" <arnd@arndb.de>
Cc: "linux@armlinux.org.uk" <linux@armlinux.org.uk>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "paul.burton@mips.com" <paul.burton@mips.com>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "salyzyn@android.com" <salyzyn@android.com>
Cc: "pcc@google.com" <pcc@google.com>
Cc: "shuah@kernel.org" <shuah@kernel.org>
Cc: "0x7f454c46@gmail.com" <0x7f454c46@gmail.com>
Cc: "linux@rasmusvillemoes.dk" <linux@rasmusvillemoes.dk>
Cc: "huw@codeweavers.com" <huw@codeweavers.com>
Cc: "sfr@canb.auug.org.au" <sfr@canb.auug.org.au>
Cc: "pbonzini@redhat.com" <pbonzini@redhat.com>
Cc: "rkrcmar@redhat.com" <rkrcmar@redhat.com>
Cc: "kvm@vger.kernel.org" <kvm@vger.kernel.org>
Link: https://lkml.kernel.org/r/1561955054-1838-2-git-send-email-mikelley@microsoft.com
Extend the davinci-timer driver to also register a clock source.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Currently the clocksource and clockevent support for davinci platforms
lives in mach-davinci. It hard-codes many things, uses global variables,
implements functionalities unused by any platform and has code fragments
scattered across many (often unrelated) files.
Implement a new, modern and simplified timer driver and put it into
drivers/clocksource. We still need to support legacy board files so
export a config structure and a function that allows machine code to
register the timer.
The timer we're using is 64-bit but can be programmed in dual 32-bit
mode (both chained and unchained).
On all davinci SoCs except for da830 we're using both halves. Lower half
for clockevents and upper half for clocksource. On da830 we're using the
lower half for both with the help of a compare register.
This patch contains the core code and support for clockevent. The
clocksource code will be included in a subsequent patch.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tegra's timer has 29 bits for the counter and for the "load" register
which sets counter to a load-value. The counter's value is lower than
the actual value by 1 because it starts to decrement after one tick,
hence the maximum number of ticks that hardware can handle equals to
29 bits + 1.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tegra's timer uses n+1 scheme for the counter, i.e. timer will fire after
one tick if 0 is loaded. The minimum and maximum numbers of oneshot ticks
are defined by clockevents_config_and_register(min, max) invocation and
the min value is set to 1 tick. Hence "cycles" value can't ever be 0,
unless it's a bug in clocksource core.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We're adjusting the timer's base for each per-CPU timer to point to the
actual start of the timer since device-tree defines a compound registers
range that includes all of the timers. In this case the original base
need to be restore before calling iounmap to unmap the proper address.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Convert all 1MHz literals to a verbose constant for better readability.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
There is no need to cast void because kernel allows to do that without
a warning message from a compiler.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The of_clk structure has a period field that is set up initially by
timer_of_clk_init(), that period value need to be adjusted for a case of
TIMER1-9 that are running at a fixed rate that doesn't match the clock's
rate. Note that the period value is currently used only by some of the
clocksource drivers internally and hence this is just a minor cleanup
change that doesn't fix anything.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It was left unnoticed by accident, which means that the code could be
cleaned up a tad more.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The clocksource rate is initialized only for the first per-CPU clocksource
and then that rate shall be replicated for the rest of clocksource's
because they are initialized manually in the code.
Fixes: 3be2a85a0b61 ("clocksource/drivers/tegra: Support per-CPU timers on all Tegra's")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Different mechanisms are used to test and set elf_hwcaps between ARM
and ARM64, this results in the use of ifdeferry in this file when
setting/testing for the EVTSTRM hwcap.
Let's improve readability by extracting this to an arch helper.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The system counter (sys_ctr) is a programmable system counter
which provides a shared time base to the Cortex A15, A7, A53 etc cores.
It is intended for use in applications where the counter is always
powered on and supports multiple, unrelated clocks. The sys_ctr hardware
supports:
- 56-bit counter width (roll-over time greater than 40 years)
- compare frame(64-bit compare value) contains programmable interrupt
generation when compare value <= counter value.
[dlezcano] Fixed over 80 chars length warning
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Rename driver's source file to better reflect that it's not specific to
older SoC generations.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Arch-timer is more preferable for a range of Tegra SoC generations as
it has higher precision and is not affect by any kind of problems.
Pointed-out-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove build dependency on ARM for compile-testing to allow non-arch
specific build-bots (like Intel's test robot) to compile the driver and
report about problems.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Correct typo and use proper upper casing for acronyms in the comments,
use common style for error messages, prepend error messages with
"tegra-timer:", add error message for cpuhp_setup_state() failure and
clean up whitespaces in the code to fix checkpatch warnings.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Release all requested IRQ's on the request error to properly clean up
allocated resources.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The readl/writel functions are inserting memory barrier to ensure that
outstanding memory writes are completed, this results in L2 cache syncing
being done on Tegra20 and Tegra30 which isn't a very cheap operation.
Replace all readl/writel occurrences in the code with the relaxed versions
since there is no need for the memory-access syncing.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reset timer's hardware state to ensure that initially it is in a
predictable state.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tegra132 is 64bit platform and it has the tegra20-timer hardware unit.
Right now the corresponding timer code isn't compiled for ARM64, remove
ifdef'iness from the code and compile tegra20-timer for both 32 and 64 bit
platforms. Also note that like the older generations, Tegra210 has the
microseconds counter, hence the timer_us clocksource is now made available
for Tegra210 as well.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Assign TMR1-4 per-CPU core on 32bit Tegra's in a way it is done for
Tegra210. In a result each core can handle its own timer events, less
code is unique to ARM64 and Tegra's clock events driver now has higher
rating on all Tegra's, replacing the ARM's TWD timer which isn't very
accurate due to the clock rate jitter caused by CPU frequency scaling.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Exynos SoCs based on CA7/CA15 have 2 timer interfaces: custom Exynos MCT
(Multi Core Timer) and standard ARM Architected Timers.
There are use cases, where both timer interfaces are used simultanously.
One of such examples is using Exynos MCT for the main system timer and
ARM Architected Timers for the KVM and virtualized guests (KVM requires
arch timers).
Exynos Multi-Core Timer driver (exynos_mct) must be however started
before ARM Architected Timers (arch_timer), because they both share some
common hardware blocks (global system counter) and turning on MCT is
needed to get ARM Architected Timer working properly.
To ensure selecting Exynos MCT as the main system timer, increase MCT
timer rating. To ensure proper starting order of both timers during
suspend/resume cycle, increase MCT hotplug priority over ARM Archictected
Timers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This is in-kernel C code, so there is no reason to use _BITUL().
Replace it with equivalent BIT().
I added #include <linux/bits.h> explicitly although it has been included
by other headers eventually.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds delay timer functionality to the IXP4xx
timer driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Comply with the licensing rules defined in the documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is licensed under the gpl v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204654.634736654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull timer fixes from Thomas Gleixner:
"A set of small fixes:
- Repair the ktime_get_coarse() functions so they actually deliver
what they are supposed to: tick granular time stamps. The current
code missed to add the accumulated nanoseconds part of the
timekeeper so the resulting granularity was 1 second.
- Prevent the tracer from infinitely recursing into time getter
functions in the arm architectured timer by marking these functions
notrace
- Fix a trivial compiler warning caused by wrong qualifier ordering"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Repair ktime_get_coarse*() granularity
clocksource/drivers/arm_arch_timer: Don't trace count reader functions
clocksource/drivers/timer-ti-dm: Change to new style declaration
With v5.2-rc1, The ftrace functions_graph tracer locks up whenever it is
enabled on arm64.
Since commit 0ea415390c ("clocksource/arm_arch_timer: Use
arch_timer_read_counter to access stable counters") a function pointer
is consistently used to read the counter instead of potentially
referencing an inlinable function.
The graph tracers relies on accessing the timer counters to compute the
time spent in functions which causes the lockup when attempting to trace
these code paths.
Annotate the arm arch timer counter accessors as notrace.
Fixes: 0ea415390c ("clocksource/arm_arch_timer: Use
arch_timer_read_counter to access stable counters")
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 of
the license as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.144869442@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 107 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.615055994@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 37 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.724130665@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not write to the free software foundation inc 59 temple place suite
330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.251475812@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'dmtimer_ops' was declared const static instead of static const.
../drivers/clocksource/timer-ti-dm.c:899:1: warning: ‘static’ is not at beginning of declaration [-Wold-style-declaration]
const static struct omap_dm_timer_ops dmtimer_ops = {
^~~~~
Signed-off-by: Philippe Mazenauer <philippe.mazenauer@outlook.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----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=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
- allow users to invoke 'make' out of the source tree
- refactor scripts/mkmakefile
- deprecate KBUILD_SRC, which was used to track the source tree
location for O= build.
- fix recordmcount.pl in case objdump output is localized
- turn unresolved symbols in external modules to errors from warnings
by default; pass KBUILD_MODPOST_WARN=1 to get them back to warnings
- generate modules.builtin.modinfo to collect .modinfo data from
built-in modules
- misc Makefile cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zj9w
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- allow users to invoke 'make' out of the source tree
- refactor scripts/mkmakefile
- deprecate KBUILD_SRC, which was used to track the source tree
location for O= build.
- fix recordmcount.pl in case objdump output is localized
- turn unresolved symbols in external modules to errors from warnings
by default; pass KBUILD_MODPOST_WARN=1 to get them back to warnings
- generate modules.builtin.modinfo to collect .modinfo data from
built-in modules
- misc Makefile cleanups
* tag 'kbuild-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
.gitignore: add more all*.config patterns
moduleparam: Save information about built-in modules in separate file
Remove MODULE_ALIAS() calls that take undefined macro
.gitignore: add leading and trailing slashes to generated directories
scripts/tags.sh: fix direct execution of scripts/tags.sh
scripts: override locale from environment when running recordmcount.pl
samples: kobject: allow CONFIG_SAMPLE_KOBJECT to become y
samples: seccomp: turn CONFIG_SAMPLE_SECCOMP into a bool option
kbuild: move Documentation to vmlinux-alldirs
kbuild: move samples/ to KBUILD_VMLINUX_OBJS
modpost: make KBUILD_MODPOST_WARN also configurable for external modules
kbuild: check arch/$(SRCARCH)/include/generated before out-of-tree build
kbuild: remove unneeded dependency for include/config/kernel.release
memory: squash drivers/memory/Makefile.asm-offsets
kbuild: use $(srctree) instead of KBUILD_SRC to check out-of-tree build
kbuild: mkmakefile: generate a simple wrapper of top Makefile
kbuild: mkmakefile: do not check the generated Makefile marker
kbuild: allow Kbuild to start from any directory
kbuild: pass $(MAKECMDGOALS) to sub-make as is
kbuild: fix warning "overriding recipe for target 'Makefile'"
...
Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here, along
with some new IIO drivers.
Also we ended up deleting two drivers, making this pull request remove a
few hundred thousand lines of code, always a nice thing to see. Both of
the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from those
locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by the
various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come in
the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHGMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynQRACgwtlC6DFsEFwCplYxQXP5uzuIVTMAoJ61xzC0
Qim7K31f5ulaa3GJuhzo
=zEY5
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
These files do not define (USBHS_)DRIVER_NAME. Yet, they can be
successfully compiled because they are never built as a module by
anyone, i.e, the MODULE_ALIAS() calls are always no-op.
A problem showed up when a patch "moduleparam: Save information about
built-in modules in separate file" was applied. With this new feature,
MODULE_*() will be populated even if the callers are built-in.
To avoid the build errors, the lines referencing to the undefined
macro must be removed.
The complete fix is to remove all MODULE_* and #include <linux/module.h>
like many "make ... explicitly non-modular" commits did.
For now, I am touching only the offending lines.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Mostly just incremental improvements here:
- Introduce AT_HWCAP2 for advertising CPU features to userspace
- Expose SVE2 availability to userspace
- Support for "data cache clean to point of deep persistence" (DC PODP)
- Honour "mitigations=off" on the cmdline and advertise status via sysfs
- CPU timer erratum workaround (Neoverse-N1 #1188873)
- Introduce perf PMU driver for the SMMUv3 performance counters
- Add config option to disable the kuser helpers page for AArch32 tasks
- Futex modifications to ensure liveness under contention
- Rework debug exception handling to seperate kernel and user handlers
- Non-critical fixes and cleanup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFGgACgkQt6xw3ITB
YzTicAf/TX1h1+ecbx4WJAa4qeiOCPoNpG9efldQumqJhKL44MR5bkhuShna5mwE
ptm5qUXkZCxLTjzssZKnbdbgwa3t+emW8Of3D91IfI9akiZbMoDx5FGgcNbqjazb
RLrhOFHwgontA38yppZN+DrL+sXbvif/CVELdHahkEx6KepSGaS2lmPXRmz/W56v
4yIRy/zxc3Dhjgfm3wKh72nBwoZdLiIc4mchd5pthNlR9E2idrYkQegG1C+gA00r
o8uZRVOWgoh7H+QJE+xLUc8PaNCg8xqRRXOuZYg9GOz6hh7zSWhm+f1nRz9S2tIR
gIgsCHNqoO2I3E1uJpAQXDGtt2kFhA==
=ulpJ
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Mostly just incremental improvements here:
- Introduce AT_HWCAP2 for advertising CPU features to userspace
- Expose SVE2 availability to userspace
- Support for "data cache clean to point of deep persistence" (DC PODP)
- Honour "mitigations=off" on the cmdline and advertise status via
sysfs
- CPU timer erratum workaround (Neoverse-N1 #1188873)
- Introduce perf PMU driver for the SMMUv3 performance counters
- Add config option to disable the kuser helpers page for AArch32 tasks
- Futex modifications to ensure liveness under contention
- Rework debug exception handling to seperate kernel and user
handlers
- Non-critical fixes and cleanup"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
Documentation: Add ARM64 to kernel-parameters.rst
arm64/speculation: Support 'mitigations=' cmdline option
arm64: ssbs: Don't treat CPUs with SSBS as unaffected by SSB
arm64: enable generic CPU vulnerabilites support
arm64: add sysfs vulnerability show for speculative store bypass
arm64: Fix size of __early_cpu_boot_status
clocksource/arm_arch_timer: Use arch_timer_read_counter to access stable counters
clocksource/arm_arch_timer: Remove use of workaround static key
clocksource/arm_arch_timer: Drop use of static key in arch_timer_reg_read_stable
clocksource/arm_arch_timer: Direcly assign set_next_event workaround
arm64: Use arch_timer_read_counter instead of arch_counter_get_cntvct
watchdog/sbsa: Use arch_timer_read_counter instead of arch_counter_get_cntvct
ARM: vdso: Remove dependency with the arch_timer driver internals
arm64: Apply ARM64_ERRATUM_1188873 to Neoverse-N1
arm64: Add part number for Neoverse N1
arm64: Make ARM64_ERRATUM_1188873 depend on COMPAT
arm64: Restrict ARM64_ERRATUM_1188873 mitigation to AArch32
arm64: mm: Remove pte_unmap_nested()
arm64: Fix compiler warning from pte_unmap() with -Wunused-but-set-variable
arm64: compat: Reduce address limit for 64K pages
...
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Allow building the PIT driver when COMPILE_TEST is enabled. Also remove its
default value so it can be disabled.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Move the ATMEL_TCB_CLKSRC option to drivers/clocksource and make it silent
if COMPILE_TEST is not selected.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Now that the driver is registered early enough, use the TCB as the
sched_clock which is much more accurate than the jiffies implementation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
atmel_tclib is probed too late in the boot process to be able to use the
TCB as the boot clocksource. This is an issue for SoCs without the PIT
(sams70, samv70 and samv71 families) as they simply currently can't boot.
Get rid of the atmel_tclib dependency and probe everything on our own using
the correct device tree binding.
This also allows getting rid of ATMEL_TCB_CLKSRC_BLOCK and makes the driver
a bit more flexible as the TCB is not hardcoded in the kernel anymore.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Aggregate common register accesses into shared functions for
maintainability.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add a shutdown operation to support shutdown timer.
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix mlb_set_oneshot_state() to enable one-shot timer.
The function should stop and start a timer, but "start" statement was
dropped. Kick the register to start one-shot timer.
Fixes: b58f28f306 ("clocksource/drivers/timer-milbeaut: Introduce timer for Milbeaut SoCs")
Signed-off-by: Sugaya Taichi <sugaya.taichi@socionext.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Since the clocksource framework has the support for suspend time
compensation. Re-work the driver to use that, so we can reduce the
duplicate code.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This is only used on arm and arm64 platforms. Add COMPILE_TEST option.
Tested with 5.1-rc3+ on Fedora/RISCV. CONFIG_ARM_TIMER_SP804 no more shows
up in riscv config.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The suniv (new F-series) chip has a timer with less functionality than
the A10 timer, e.g. it has only 3 channels.
Add a new compatible for it. As we didn't use the extra channels on A10
either now, the code needn't to be changed.
The suniv chip is based on ARM926EJ-S CPU, thus it has no architecture timer.
Register sun4i_timer as sched_clock on it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Instead of always going via arch_counter_get_cntvct_stable to access the
counter workaround, let's have arch_timer_read_counter point to the
right method.
For that, we need to track whether any CPU in the system has a
workaround for the counter. This is done by having an atomic variable
tracking this.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The use of a static key in a hotplug path has proved to be a real
nightmare, and makes it impossible to have scream-free lockdep
kernel.
Let's remove the static key altogether, and focus on something saner.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tony Lindgren