Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=b0/p
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
MMC core:
- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
* tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc: (68 commits)
mmc: dw_mmc: remove the deprecated "supports-highspeed" property
mmc: dw_mmc: minor cleanup for dw_mci_adjust_fifoth
mmc: dw_mmc: use macro to define ring buffer size
mmc: dw_mmc: fix misleading error print if failing to do DMA transfer
mmc: dw_mmc: avoid race condition of cpu and IDMAC
mmc: dw_mmc: split out preparation of desc for IDMAC32 and IDMAC64
mmc: core: don't try to switch block size for dual rate mode
mmc: sdhci-of-arasan: Set controller to test mode when no CD bit
dt: sdhci-of-arasan: Add device tree option xlnx, fails-without-test-cd
mmc: tmio: add eMMC support
mmc: rtsx_usb: use new macro for R1 without CRC
mmc: rtsx_pci: use new macro for R1 without CRC
mmc: add define for R1 response without CRC
mmc: card: do away with indirection pointer
mmc: sdhci-acpi: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci-pci: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci: Support cap_cmd_during_tfr requests
mmc: mmc_test: Add tests for sending commands during transfer
mmc: core: Add support for sending commands during data transfer
mmc: sdhci-brcmstb: Fix incorrect capability
...
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
In a virtualized environment the APIC timer calibration can go wrong when
the host is overcommitted or the guest is running nested. This results
in the APIC timers operating at an incorrect frequency.
Since VMware supports a mechanism to retrieve the local APIC frequency we
can ask the hypervisor for it and skip the APIC calibration loop.
Signed-off-by: Renat Valiullin <rvaliullin@vmware.com>
Acked-by: Alok N Kataria <akataria@vmware.com>
Cc: virtualization@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20161004201148.GA1421@uu64vm
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
xen_cpuhp_setup() calls mutex_lock() which, when CONFIG_DEBUG_MUTEXES
is defined, ends up calling xen_save_fl(). That routine expects
per_cpu(xen_vcpu, 0) to be already initialized.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Pull s390 updates from Martin Schwidefsky:
"The new features and main improvements in this merge for v4.9
- Support for the UBSAN sanitizer
- Set HAVE_EFFICIENT_UNALIGNED_ACCESS, it improves the code in some
places
- Improvements for the in-kernel fpu code, in particular the overhead
for multiple consecutive in kernel fpu users is recuded
- Add a SIMD implementation for the RAID6 gen and xor operations
- Add RAID6 recovery based on the XC instruction
- The PCI DMA flush logic has been improved to increase the speed of
the map / unmap operations
- The time synchronization code has seen some updates
And bug fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
s390/con3270: fix insufficient space padding
s390/con3270: fix use of uninitialised data
MAINTAINERS: update DASD maintainer
s390/cio: fix accidental interrupt enabling during resume
s390/dasd: add missing \n to end of dev_err messages
s390/config: Enable config options for Docker
s390/dasd: make query host access interruptible
s390/dasd: fix panic during offline processing
s390/dasd: fix hanging offline processing
s390/pci_dma: improve lazy flush for unmap
s390/pci_dma: split dma_update_trans
s390/pci_dma: improve map_sg
s390/pci_dma: simplify dma address calculation
s390/pci_dma: remove dma address range check
iommu/s390: simplify registration of I/O address translation parameters
s390: migrate exception table users off module.h and onto extable.h
s390: export header for CLP ioctl
s390/vmur: fix irq pointer dereference in int handler
s390/dasd: add missing KOBJ_CHANGE event for unformatted devices
s390: enable UBSAN
...
buffers (Thor Thayer)
* Split the memory controller part out of mpc85xx and share it with a
* new Freescale ARM Layerscape driver (York Sun)
* amd64_edac fixes (Yazen Ghannam)
* Misc cleanups, refactoring and fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pcI8
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A lot of movement in the EDAC tree this time around, coarse summary
below:
- Altera Arria10 enablement of NAND, DMA, USB, QSPI and SD-MMC FIFO
buffers (Thor Thayer)
- split the memory controller part out of mpc85xx and share it with a
new Freescale ARM Layerscape driver (York Sun)
- amd64_edac fixes (Yazen Ghannam)
- misc cleanups, refactoring and fixes all over the place"
* tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (37 commits)
EDAC, altera: Add IRQ Flags to disable IRQ while handling
EDAC, altera: Correct EDAC IRQ error message
EDAC, amd64: Autoload module using x86_cpu_id
EDAC, sb_edac: Remove NULL pointer check on array pci_tad
EDAC: Remove NO_IRQ from powerpc-only drivers
EDAC, fsl_ddr: Fix error return code in fsl_mc_err_probe()
EDAC, fsl_ddr: Add entry to MAINTAINERS
EDAC: Move Doug Thompson to CREDITS
EDAC, I3000: Orphan driver
EDAC, fsl_ddr: Replace simple_strtoul() with kstrtoul()
EDAC, layerscape: Add Layerscape EDAC support
EDAC, fsl_ddr: Fix IRQ dispose warning when module is removed
EDAC, fsl_ddr: Add support for little endian
EDAC, fsl_ddr: Add missing DDR DRAM types
EDAC, fsl_ddr: Rename macros and names
EDAC, fsl-ddr: Separate FSL DDR driver from MPC85xx
EDAC, mpc85xx: Replace printk() with pr_* format
EDAC, mpc85xx: Drop setting/clearing RFXE bit in HID1
EDAC, altera: Rename MC trigger to common name
EDAC, altera: Rename device trigger to common name
...
that weren't causing enough problems (or any problems when we're just
clarifying things) to warrant sending outside the merge window. The
majority of changes are in drivers for various SoCs. Full details
are in the logs, but here's the summary.
Core:
- Better support for DeviceTree overlays with the addition of the
CLK_OF_DECLARE_DRIVER macro. Now we won't probe a clk driver
for a device node that matched during of_clk_init(), unless
the driver uses CLK_OF_DECLARE_DRIVER instead of CLK_OF_DECLARE.
This allows overlays to work cleanly for drivers that must probe
before the device model is ready, and also after it's ready
when an overlay is loaded.
- Clarification in the code around how clk_hw pointers are returned
from of clk providers
- Proper migration of prepare/enable counts to parents when the
clk tree is constructed
New Drivers:
- Socionext's UniPhier SoCs
- Loongson1C
- ZTE ZX296718
- Qualcomm MDM9615
- Amlogic GXBB AO clocks and resets
- Broadcom BCM53573 ILP
- Maxim MAX77620
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver (A31, A31s,
A23 and A33)
- Exynos 5xxx audio and DRAM clks
- Loongson1B AC97, DMA and NAND clks
- Rockchip DDR clks and rk3399 driver tweaks
- Renesas R-Car M3-W (r8a7796) SoC SDHI interface and Watchdog timer clks
- Renasas R-Car H3 and M3-W CMT clks and RAVB+Thermal clks for M3-W
- Amlogic GXBB MMC gate clks
- at91 sama5d4 sckc
- Removal of STiH415 and STiH416 clk support as the SoC is being removed
- Rework of STiH4xx clk support for new style bindings
- Continuation of driver migration to clk_hw based registration APIs
- xgene PMD support
- bcm2835 critical clk markings
- ARM versatile ICST
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=NFUB
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk framework updates from Stephen Boyd:
"The core clk framework changes are small again. They're mostly minor
fixes that weren't causing enough problems (or any problems when we're
just clarifying things) to warrant sending outside the merge window.
The majority of changes are in drivers for various SoCs. Full details
are in the logs, but here's the summary.
Core:
- Better support for DeviceTree overlays with the addition of the
CLK_OF_DECLARE_DRIVER macro. Now we won't probe a clk driver for a
device node that matched during of_clk_init(), unless the driver
uses CLK_OF_DECLARE_DRIVER instead of CLK_OF_DECLARE. This allows
overlays to work cleanly for drivers that must probe before the
device model is ready, and also after it's ready when an overlay is
loaded.
- Clarification in the code around how clk_hw pointers are returned
from of clk providers
- Proper migration of prepare/enable counts to parents when the clk
tree is constructed
New Drivers:
- Socionext's UniPhier SoCs
- Loongson1C
- ZTE ZX296718
- Qualcomm MDM9615
- Amlogic GXBB AO clocks and resets
- Broadcom BCM53573 ILP
- Maxim MAX77620
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver (A31,
A31s, A23 and A33)
- Exynos 5xxx audio and DRAM clks
- Loongson1B AC97, DMA and NAND clks
- Rockchip DDR clks and rk3399 driver tweaks
- Renesas R-Car M3-W (r8a7796) SoC SDHI interface and Watchdog timer
clks
- Renasas R-Car H3 and M3-W CMT clks and RAVB+Thermal clks for M3-W
- Amlogic GXBB MMC gate clks
- at91 sama5d4 sckc
- Removal of STiH415 and STiH416 clk support as the SoC is being
removed
- Rework of STiH4xx clk support for new style bindings
- Continuation of driver migration to clk_hw based registration APIs
- xgene PMD support
- bcm2835 critical clk markings
- ARM versatile ICST"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (199 commits)
CLK: Add Loongson1C clock support
clk: Loongson1: Make use of GENMASK
clk: Loongson1: Update clocks of Loongson1B
clk: Loongson1: Refactor Loongson1 clock
clk: change the type of clk_hw_onecell_data.num to unsigned int
clk: zx296718: register driver earlier with core_initcall
clk: mvebu: dynamically allocate resources in Armada CP110 system controller
clk: mvebu: fix setting unwanted flags in CP110 gate clock
clk: nxp: clk-lpc32xx: Unmap region obtained by of_iomap
clk: mediatek: clk-mt8173: Unmap region obtained by of_iomap
clk: sunxi-ng: Fix reset offset for the A23 and A33
clk: at91: sckc: optimize boot time
clk: at91: Add sama5d4 sckc support
clk: at91: move slow clock controller clocks to sckc.c
clk: imx6: initialize GPU clocks
clk: imx6: fix i.MX6DL clock tree to reflect reality
clk: imx53: Add clocks configuration
clk: uniphier: add clock data for UniPhier SoCs
clk: uniphier: add core support code for UniPhier clock driver
clk: bcm: Add driver for BCM53573 ILP clock
...
Move the driver source and Kconfig to the PCI host bridge drivers directory
and move the config option to a more appropriate sub-menu instead of
occupying the top-level location.
Update the Kconfig option with the X86_64 dependency that was implicitly
included from the previous location, and add information about the module
name when built as a loadable module.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jon Derrick <jonathan.derrick@intel.com>
When a CPU is about to be offlined we call fixup_irqs() that resets IRQ
affinities related to the CPU in question. The same thing is also done when
the system is suspended to S-states like S3 (mem).
For each IRQ we try to complete any on-going move regardless whether the
IRQ is actually part of x86_vector_domain. For each IRQ descriptor we fetch
its chip_data, assume it is of type struct apic_chip_data and manipulate it
by clearing old_domain mask etc. For irq_chips that are not part of the
x86_vector_domain, like those created by various GPIO drivers, will find
their chip_data being changed unexpectly.
Below is an example where GPIO chip owned by pinctrl-sunrisepoint.c gets
corrupted after resume:
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in hi
# rtcwake -s10 -mmem
<10 seconds passes>
# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 360-511, parent: platform/INT344B:00, INT344B:00:
gpio-511 ( |sysfs ) in ?
Note '?' in the output. It means the struct gpio_chip ->get function is
NULL whereas before suspend it was there.
Fix this by first checking that the IRQ belongs to x86_vector_domain before
we try to use the chip_data as struct apic_chip_data.
Reported-and-tested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org # 4.4+
Link: http://lkml.kernel.org/r/20161003101708.34795-1-mika.westerberg@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tail calls allow JIT'ed eBPF programs to call into other JIT'ed eBPF
programs. This can be achieved either by:
(1) retaining the stack setup by the first eBPF program and having all
subsequent eBPF programs re-using it, or,
(2) by unwinding/tearing down the stack and having each eBPF program
deal with its own stack as it sees fit.
To ensure that this does not create loops, there is a limit to how many
tail calls can be done (currently 32). This requires the JIT'ed code to
maintain a count of the number of tail calls done so far.
Approach (1) is simple, but requires every eBPF program to have (almost)
the same prologue/epilogue, regardless of whether they need it. This is
inefficient for small eBPF programs which may not sometimes need a
prologue at all. As such, to minimize impact of tail call
implementation, we use approach (2) here which needs each eBPF program
in the chain to use its own prologue/epilogue. This is not ideal when
many tail calls are involved and when all the eBPF programs in the chain
have similar prologue/epilogue. However, the impact is restricted to
programs that do tail calls. Individual eBPF programs are not affected.
We maintain the tail call count in a fixed location on the stack and
updated tail call count values are passed in through this. The very
first eBPF program in a chain sets this up to 0 (the first 2
instructions). Subsequent tail calls skip the first two eBPF JIT
instructions to maintain the count. For programs that don't do tail
calls themselves, the first two instructions are NOPs.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While at it, ensure that the location of the local save area is
consistent whether or not we setup our own stackframe. This property is
utilised in the next patch that adds support for tail calls.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The fadump code calls vmcore_cleanup() which only exists if
CONFIG_PROC_VMCORE=y. We don't want to depend on CONFIG_PROC_VMCORE,
because it's user selectable, so just wrap the call in an #ifdef.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the MSR TM bit is always set if the hardware is TM capable.
This adds extra overhead as it means the TM SPRS (TFHAR, TEXASR and
TFAIR) must be swapped for each process regardless of if they use TM.
For processes that don't use TM the TM MSR bit can be turned off
allowing the kernel to avoid the expensive swap of the TM registers.
A TM unavailable exception will occur if a thread does use TM and the
kernel will enable MSR_TM and leave it so for some time afterwards.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the kernel disables transactional memory (TM) and userspace still
tries TM related actions (TM instructions or TM SPR accesses) TM aware
hardware will cause the kernel to take a facility unavailable
exception.
Add checks for the exception being caused by illegal TM access in
userspace.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Rewrite comment entirely, bugs in it are mine]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make the structures being used for checkpointed state named
consistently with the pt_regs/ckpt_regs.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is currently an inconsistency as to how the entire CPU register
state is saved and restored when a thread uses transactional memory
(TM).
Using transactional memory results in the CPU having duplicated
(almost) all of its register state. This duplication results in a set
of registers which can be considered 'live', those being currently
modified by the instructions being executed and another set that is
frozen at a point in time.
On context switch, both sets of state have to be saved and (later)
restored. These two states are often called a variety of different
things. Common terms for the state which only exists after the CPU has
entered a transaction (performed a TBEGIN instruction) in hardware are
'transactional' or 'speculative'.
Between a TBEGIN and a TEND or TABORT (or an event that causes the
hardware to abort), regardless of the use of TSUSPEND the
transactional state can be referred to as the live state.
The second state is often to referred to as the 'checkpointed' state
and is a duplication of the live state when the TBEGIN instruction is
executed. This state is kept in the hardware and will be rolled back
to on transaction failure.
Currently all the registers stored in pt_regs are ALWAYS the live
registers, that is, when a thread has transactional registers their
values are stored in pt_regs and the checkpointed state is in
ckpt_regs. A strange opposite is true for fp_state/vr_state. When a
thread is non transactional fp_state/vr_state holds the live
registers. When a thread has initiated a transaction fp_state/vr_state
holds the checkpointed state and transact_fp/transact_vr become the
structure which holds the live state (at this point it is a
transactional state).
This method creates confusion as to where the live state is, in some
circumstances it requires extra work to determine where to put the
live state and prevents the use of common functions designed (probably
before TM) to save the live state.
With this patch pt_regs, fp_state and vr_state all represent the
same thing and the other structures [pending rename] are for
checkpointed state.
Acked-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Much of the signal code takes a pt_regs on which it operates. Over
time the signal code has needed to know more about the thread than
what pt_regs can supply, this information is obtained as needed by
using 'current'.
This approach is not strictly incorrect however it does mean that
there is now a hard requirement that the pt_regs being passed around
does belong to current, this is never checked. A safer approach is for
the majority of the signal functions to take a task_struct from which
they can obtain pt_regs and any other information they need. The
caveat that the task_struct they are passed must be current doesn't go
away but can more easily be checked for.
Functions called from outside powerpc signal code are passed a pt_regs
and they can confirm that the pt_regs is that of current and pass
current to other functions, furthurmore, powerpc signal functions can
check that the task_struct they are passed is the same as current
avoiding possible corruption of current (or the task they are passed)
if this assertion ever fails.
CC: paulus@samba.org
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After a thread is reclaimed from its active or suspended transactional
state the checkpointed state exists on CPU, this state (along with the
live/transactional state) has been saved in its entirety by the
reclaiming process.
There exists a sequence of events that would cause the kernel to call
one of enable_kernel_fp(), enable_kernel_altivec() or
enable_kernel_vsx() after a thread has been reclaimed. These functions
save away any user state on the CPU so that the kernel can use the
registers. Not only is this saving away unnecessary at this point, it
is actually incorrect. It causes a save of the checkpointed state to
the live structures within the thread struct thus destroying the true
live state for that thread.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
msr_check_and_set() always performs a mfmsr() to determine if it needs
to perform an mtmsr(), as mfmsr() can be a costly operation
msr_check_and_set() could return the MSR now on the CPU to avoid
callers of msr_check_and_set having to make their own mfmsr() call.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
giveup_all() causes FPU/VMX/VSX facilities to be disabled in a threads
MSR. If the thread performing the giveup was transactional, the kernel
must record which facilities were in use before the giveup as the
thread must have these facilities re-enabled on return to userspace.
>From process.c:
/*
* This is called if we are on the way out to userspace and the
* TIF_RESTORE_TM flag is set. It checks if we need to reload
* FP and/or vector state and does so if necessary.
* If userspace is inside a transaction (whether active or
* suspended) and FP/VMX/VSX instructions have ever been enabled
* inside that transaction, then we have to keep them enabled
* and keep the FP/VMX/VSX state loaded while ever the transaction
* continues. The reason is that if we didn't, and subsequently
* got a FP/VMX/VSX unavailable interrupt inside a transaction,
* we don't know whether it's the same transaction, and thus we
* don't know which of the checkpointed state and the transactional
* state to use.
*/
Calling check_if_tm_restore_required() will set TIF_RESTORE_TM and
save the MSR if needed.
Fixes: c208505 ("powerpc: create giveup_all()")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Comment from arch/powerpc/kernel/process.c:967:
If userspace is inside a transaction (whether active or
suspended) and FP/VMX/VSX instructions have ever been enabled
inside that transaction, then we have to keep them enabled
and keep the FP/VMX/VSX state loaded while ever the transaction
continues. The reason is that if we didn't, and subsequently
got a FP/VMX/VSX unavailable interrupt inside a transaction,
we don't know whether it's the same transaction, and thus we
don't know which of the checkpointed state and the ransactional
state to use.
restore_math() restore_fp() and restore_altivec() currently may not
restore the registers. It doesn't appear that this is more serious
than a performance penalty. If the math registers aren't restored the
userspace thread will still be run with the facility disabled.
Userspace will not be able to read invalid values. On the first access
it will take an facility unavailable exception and the kernel will
detected an active transaction, at which point it will abort the
transaction. There is the possibility for a pathological case
preventing any progress by transactions, however, transactions
are never guaranteed to make progress.
Fixes: 70fe3d9 ("powerpc: Restore FPU/VEC/VSX if previously used")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes warning reported from sparse:
pci-ioda.c:451:49: warning: incorrect type in argument 2 (different base types)
Fixes: 262af557dd ("powerpc/powernv: Enable M64 aperatus for PHB3")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes the warning reported from sparse:
eeh-powernv.c:875:23: warning: constant 0x8000000000000000 is so big it is unsigned long
Fixes: ebe2253127 ("powerpc/powernv: Support PCI slot ID")
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hub diag-data type is filled with big-endian data by OPAL call
opal_pci_get_hub_diag_data(). We need convert it to CPU-endian value
before using it. The issue is reported by sparse as pointed by Michael
Ellerman:
eeh-powernv.c:1309:21: warning: restricted __be16 degrades to integer
This converts hub diag-data type to CPU-endian before using it in
pnv_eeh_get_and_dump_hub_diag().
Fixes: 2a485ad7c8 ("powerpc/powernv: Drop PHB operation next_error()")
Cc: stable@vger.kernel.org # v4.1+
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PE number (@frozen_pe_no), filled by opal_pci_next_error() is in
big-endian format. It should be converted to CPU-endian before it is
passed to opal_pci_eeh_freeze_clear() when clearing the frozen state if
the PE is invalid one. As Michael Ellerman pointed out, the issue is
also detected by sparse:
eeh-powernv.c:1541:41: warning: incorrect type in argument 2 (different base types)
This passes CPU-endian PE number to opal_pci_eeh_freeze_clear() and it
should be part of commit <0f36db77643b> ("powerpc/eeh: Fix wrong printed
PE number"), which was merged to 4.3 kernel.
Fixes: 71b540adff ("powerpc/powernv: Don't escalate non-existing frozen PE")
Cc: stable@vger.kernel.org # v4.3+
Suggested-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We supported POWER7 CPUs for bootstrapping little endian, but the
target was always POWER8. Now that POWER7 specific issues are
impacting performance, change the default target to POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER8 handles unaligned accesses in little endian mode, but commit
0b5e6661ac ("powerpc: Don't set HAVE_EFFICIENT_UNALIGNED_ACCESS on
little endian builds") disabled it for all.
The issue with unaligned little endian accesses is specific to POWER7,
so update the Kconfig check to match. Using the stat() testcase from
commit a75c380c71 ("powerpc: Enable DCACHE_WORD_ACCESS on ppc64le"),
performance improves 15% on POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I see quite a lot of static branch mispredictions on a simple
web serving workload. The issue is in __atomic_add_unless(), called
from _atomic_dec_and_lock(). There is no obvious common case, so it
is better to let the hardware predict the branch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During context switch, switch_mm() sets our current CPU in mm_cpumask.
We can avoid this atomic sequence in most cases by checking before
setting the bit.
Testing on a POWER8 using our context switch microbenchmark:
tools/testing/selftests/powerpc/benchmarks/context_switch \
--process --no-fp --no-altivec --no-vector
Performance improves 2%.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No real need for this to be pr_warn(), reduce it to pr_info().
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are starting to see i40e adapters in recent machines, so enable
it in our configs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change a few devices and filesystems that are seldom used any more
from built in to modules. This reduces our vmlinux about 500kB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we issue a system reset, every CPU in the box prints an Oops,
including a backtrace. Each of these can be quite large (over 4kB)
and we may end up wrapping the ring buffer and losing important
information.
Bump the base size from 128kB to 256kB and the per CPU size from
4kB to 8kB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We see big improvements with the VMX crypto functions (often 10x or more),
so enable it as a module.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Align the hot loops in our assembly implementation of memset()
and backwards_memcpy().
backwards_memcpy() is called from tcp_v4_rcv(), so we might
want to optimise this a little more.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Here is the big TTY and Serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by some
serial drivers, and they were all acked by the DMA maintainer. Also in
here is the long-suffering ACPI SPCR patchset, which was passed around
from maintainer to maintainer like a hot-potato. Seems I was the
sucker^Wlucky one. All of those patches have been acked by the various
subsystem maintainers as well.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNjEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwIcAn2uN
qCD8xQJ0Cs61hD1nUzhNygG8AJ94I4zz/fPGpyh/CtJfLQwtUdLhNA==
=Rken
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems that
flow through me. Nothing major that I can discern, full details are in
the shortlog.
All have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFUEABECABYFAlfyOIQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp9OQAlRy3
gSKfQUlXjTs96Bx/I5PtWysAn0r8nyKZoP1oSgsTddOCEeXngTXc
=4uPs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems
that flow through me. Nothing major that I can discern, full details
are in the shortlog.
All have been in the linux-next tree with no reported issues"
* tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits)
drivers/misc/hpilo: Changes to support new security states in iLO5 FW
at25: fix debug and error messaging
misc/genwqe: ensure zero initialization
vme: fake: remove unexpected unlock in fake_master_set()
vme: fake: mark symbols static where possible
spmi: pmic-arb: Return an error code if sanity check fails
Drivers: hv: get rid of id in struct vmbus_channel
Drivers: hv: make VMBus bus ids persistent
mcb: Add a dma_device to mcb_device
mcb: Enable PCI bus mastering by default
mei: stop the stall timer worker if not needed
clk: probe common clock drivers earlier
vme: fake: fix build for 64-bit dma_addr_t
ttyprintk: Neaten and simplify printing
mei: me: add kaby point device ids
coresight: tmc: mark symbols static where possible
coresight: perf: deal with error condition properly
Drivers: hv: hv_util: Avoid dynamic allocation in time synch
fpga manager: Add hardware dependency to Zynq driver
Drivers: hv: utils: Support TimeSync version 4.0 protocol samples.
...
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
Pull irq updates from Thomas Gleixner:
"The irq departement proudly presents:
- A rework of the core infrastructure to optimally spread interrupt
for multiqueue devices. The first version was a bit naive and
failed to take thread siblings and other details into account.
Developed in cooperation with Christoph and Keith.
- Proper delegation of softirqs to ksoftirqd, so if ksoftirqd is
active then no further softirq processsing on interrupt return
happens. Otherwise we try to delegate and still run another batch
of network packets in the irq return path, which then tries to
delegate to ksoftirqd .....
- A proper machine parseable sysfs based alternative for
/proc/interrupts.
- ACPI support for the GICV3-ITS and ARM interrupt remapping
- Two new irq chips from the ARM SoC zoo: STM32-EXTI and MVEBU-PIC
- A new irq chip for the JCore (SuperH)
- The usual pile of small fixlets in core and irqchip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
softirq: Let ksoftirqd do its job
genirq: Make function __irq_do_set_handler() static
ARM/dts: Add EXTI controller node to stm32f429
ARM/STM32: Select external interrupts controller
drivers/irqchip: Add STM32 external interrupts support
Documentation/dt-bindings: Document STM32 EXTI controller bindings
irqchip/mips-gic: Use for_each_set_bit to iterate over local IRQs
pci/msi: Retrieve affinity for a vector
genirq/affinity: Remove old irq spread infrastructure
genirq/msi: Switch to new irq spreading infrastructure
genirq/affinity: Provide smarter irq spreading infrastructure
genirq/msi: Add cpumask allocation to alloc_msi_entry
genirq: Expose interrupt information through sysfs
irqchip/gicv3-its: Use MADT ITS subtable to do PCI/MSI domain initialization
irqchip/gicv3-its: Factor out PCI-MSI part that might be reused for ACPI
irqchip/gicv3-its: Probe ITS in the ACPI way
irqchip/gicv3-its: Refactor ITS DT init code to prepare for ACPI
irqchip/gicv3-its: Cleanup for ITS domain initialization
PCI/MSI: Setup MSI domain on a per-device basis using IORT ACPI table
ACPI: Add new IORT functions to support MSI domain handling
...
This was not done before the big patches because I only noticed
them afterwards. It has become much easier to see which handlers
are branched to from which exception vectors now, and to see
exactly what vector space is being used for what.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simple substitution. This is possible now that both parts of the OOL
initial handler get linked into their correct location.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is not an exception handler as such, it's called from
local_irq_enable(), not exception entry.
Also clean up some now redundant comments at the end of the
consolidation series.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use assembler sections of fixed size and location to arrange the 64-bit
Book3S exception vector code (64-bit Book3E also uses it in head_64.S
for 0x0..0x100).
This allows better flexibility in arranging exception code and hiding
unimportant details behind macros.
Gas sections can be a bit painful to use this way, mainly because the
assembler does not know where they will be finally linked. Taking
absolute addresses requires a bit of trickery for example, but it can
be hidden behind macros for the most part.
Generated code is mostly the same except locations, offsets, alignments.
The "+ 0x2" is only required for the trap number / kvm exit number,
which gets loaded as a constant into a register.
Previously, code also used + 0x2 for label names, but we changed to
using "H" to distinguish HV case for that. Remove the last vestiges
of that.
__after_prom_start is taking absolute address of a label in another
fixed section. Newer toolchains seemed to compile this okay, but older
ones do not. FIXED_SYMBOL_ABS_ADDR is more foolproof, it just takes an
additional line to define.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With a subsequent patch to put text into different sections,
(_end - _stext) can no longer be computed at link time to determine
the end of the copy. Instead, calculate it at runtime with
(copy_to_here - _stext) + (_end - copy_to_here).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move exception handler alignment directives into the head-64.h macros,
beause they will no longer work in-place after the next patch. This
slightly changes functions that have alignments applied and therefore
code generation, which is why it was not done initially (see earlier
patch).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Create arch/powerpc/include/asm/head-64.h with macros that specify
an exception vector (name, type, location), which will be used to
label and lay out exceptions into the object file.
Naming is moved out of exception-64s.h, which is used to specify the
implementation of exception handlers.
objdump of generated code in exception vectors is unchanged except for
names. Alignment directives scattered around are annoying, but done
this way so that disassembly can verify identical instruction
generation before and after patch. These get cleaned up in future
patch.
We change the way KVMTEST works, explicitly passing EXC_HV or EXC_STD
rather than overloading the trap number. This removes the need to have
SOFTEN values for the overloaded trap numbers, eg. 0x502.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- ARCv2 support for native 64-bit atomics using LLOCK/SCONDD instructions
- Support for upcoming 3.0 release of HS38 cores
- Dwarf unwindinder improvements
- Ebaling unwinding out of hand written assembler code using CFI pseudo-ops
- switching to .eh_frame (as opposed to historic .debug_frame)
- getting rid of bunch of adhoc band-aids in the process
- Miscll fixes
- perf supporting generic cache-referecnes and cache-misses (Alexey)
- default NODE_SHIFT (Noam Camus)
- usage of KFLAG instruction to set IE (Yuriy)
- Platforms
- Adding "model" proprty across the DT (Alexey)
- Enabling MODULE_* in defconfigs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q/md
-----END PGP SIGNATURE-----
Merge tag 'arc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- ARCv2 support for native 64-bit atomics using LLOCK/SCONDD
instructions
- Support for upcoming 3.0 release of HS38 cores
- Dwarf unwindinder improvements:
- enable unwinding of hand written assembler code using CFI
pseudo-ops
- switch to .eh_frame (as opposed to historic .debug_frame)
- get rid of a bunch of adhoc band-aids in the process
- Misc fixes:
- perf supporting generic cache-references and cache-misses (Alexey)
- default NODE_SHIFT (Noam Camus)
- usage of KFLAG instruction to set IE (Yuriy)
- Platforms:
- Add "model" property across the DT (Alexey)
- Enable MODULE_* in defconfigs
* tag 'arc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat*] enables MODULE*
ARCv2: fix local_save_flags
ARC: CONFIG_NODES_SHIFT fix default values
ARCv2: intc: Use kflag if STATUS32.IE must be reset
ARC: .exit.* sections can be discarded in .eh_frame regime
ARC: dw2 unwind: enable cfi pseudo ops in string lib
ARC: dw2 unwind: add infrastructure for adding cfi pseudo ops to asm
ARC: entry: make ret_from_system_call local label
ARC: dw2 unwind: don't force dwarf 2
ARC: dw2 unwind: switch to .eh_frame based unwinding
ARC: dw2 unwind: factor CIE specifics for .eh_frame/.debug_frame
ARC: module: support R_ARC_32_PCREL relocation
arc: perf: Enable generic "cache-references" and "cache-misses" events
ARC: [plat-eznps] add missing atomic_fetch_xxx operations
ARCv2: Implement atomic64 based on LLOCKD/SCONDD instructions
ARCv2: Support dynamic peripheral address space in HS38 rel 3.0 cores
ARCv2: identify HS38 rel 3.0 cores
ARCv2: Add support for ZeBu Emulation platform for HS cores
arc: Add "model" properly in device tree description of all boards
Pull x86 vdso updates from Ingo Molnar:
"The main changes in this cycle centered around adding support for
32-bit compatible C/R of the vDSO on 64-bit kernels, by Dmitry
Safonov"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Use CONFIG_X86_X32_ABI to enable vdso prctl
x86/vdso: Only define map_vdso_randomized() if CONFIG_X86_64
x86/vdso: Only define prctl_map_vdso() if CONFIG_CHECKPOINT_RESTORE
x86/signal: Add SA_{X32,IA32}_ABI sa_flags
x86/ptrace: Down with test_thread_flag(TIF_IA32)
x86/coredump: Use pr_reg size, rather that TIF_IA32 flag
x86/arch_prctl/vdso: Add ARCH_MAP_VDSO_*
x86/vdso: Replace calculate_addr in map_vdso() with addr
x86/vdso: Unmap vdso blob on vvar mapping failure
Pull x86 timer updates from Ingo Molnar:
"This tree includes a HPET overhead micro-optimization plus new TSC
frequencies for newer Intel CPUs"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Add additional Intel CPU models to the crystal quirk list
x86/tsc: Use cpu id defines instead of hex constants
x86/hpet: Reduce HPET counter read contention
Pull x86 platform changes from Ingo Molnar:
"The main changes in this cycle were:
- SGI UV updates (Andrew Banman)
- Intel MID updates (Andy Shevchenko)
- Initial Mellanox systems platform (Vadim Pasternak)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/mellanox: Fix return value check in mlxplat_init()
x86/platform/mellanox: Introduce support for Mellanox systems platform
x86/platform/uv/BAU: Add UV4-specific functions
x86/platform/uv/BAU: Fix payload queue setup on UV4 hardware
x86/platform/uv/BAU: Disable software timeout on UV4 hardware
x86/platform/uv/BAU: Populate ->uvhub_version with UV4 version information
x86/platform/uv/BAU: Use generic function pointers
x86/platform/uv/BAU: Add generic function pointers
x86/platform/uv/BAU: Convert uv_physnodeaddr() use to uv_gpa_to_offset()
x86/platform/uv/BAU: Clean up pq_init()
x86/platform/uv/BAU: Clean up and update printks
x86/platform/uv/BAU: Clean up vertical alignment
x86/platform/intel-mid: Keep SRAM powered on at boot
x86/platform/intel-mid: Add Intel Penwell to ID table
x86/cpu: Rename Merrifield2 to Moorefield
x86/platform/intel-mid: Implement power off sequence
x86/platform/intel-mid: Enable SD card detection on Merrifield
x86/platform/intel-mid: Enable WiFi on Intel Edison
x86/platform/intel-mid: Run PWRMU command immediately
Pull x86 cleanups from Ingo Molnar:
"Header file and a wrapper functions cleanup"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Migrate exception table users off module.h and onto extable.h
x86: Clean up various simple wrapper functions
Pull x86 boot updates from Ingo Molnar:
"The changes in this cycle were:
- Save e820 table RAM footprint on larger kernel configurations.
(Denys Vlasenko)
- pmem related fixes (Dan Williams)
- theoretical e820 boundary condition fix (Wei Yang)"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix kdump, cleanup aborted E820_PRAM max_pfn manipulation
x86/e820: Use much less memory for e820/e820_saved, save up to 120k
x86/e820: Prepare e280 code for switch to dynamic storage
x86/e820: Mark some static functions __init
x86/e820: Fix very large 'size' handling boundary condition
Pull low-level x86 updates from Ingo Molnar:
"In this cycle this topic tree has become one of those 'super topics'
that accumulated a lot of changes:
- Add CONFIG_VMAP_STACK=y support to the core kernel and enable it on
x86 - preceded by an array of changes. v4.8 saw preparatory changes
in this area already - this is the rest of the work. Includes the
thread stack caching performance optimization. (Andy Lutomirski)
- switch_to() cleanups and all around enhancements. (Brian Gerst)
- A large number of dumpstack infrastructure enhancements and an
unwinder abstraction. The secret long term plan is safe(r) live
patching plus maybe another attempt at debuginfo based unwinding -
but all these current bits are standalone enhancements in a frame
pointer based debug environment as well. (Josh Poimboeuf)
- More __ro_after_init and const annotations. (Kees Cook)
- Enable KASLR for the vmemmap memory region. (Thomas Garnier)"
[ The virtually mapped stack changes are pretty fundamental, and not
x86-specific per se, even if they are only used on x86 right now. ]
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/asm: Get rid of __read_cr4_safe()
thread_info: Use unsigned long for flags
x86/alternatives: Add stack frame dependency to alternative_call_2()
x86/dumpstack: Fix show_stack() task pointer regression
x86/dumpstack: Remove dump_trace() and related callbacks
x86/dumpstack: Convert show_trace_log_lvl() to use the new unwinder
oprofile/x86: Convert x86_backtrace() to use the new unwinder
x86/stacktrace: Convert save_stack_trace_*() to use the new unwinder
perf/x86: Convert perf_callchain_kernel() to use the new unwinder
x86/unwind: Add new unwind interface and implementations
x86/dumpstack: Remove NULL task pointer convention
fork: Optimize task creation by caching two thread stacks per CPU if CONFIG_VMAP_STACK=y
sched/core: Free the stack early if CONFIG_THREAD_INFO_IN_TASK
lib/syscall: Pin the task stack in collect_syscall()
x86/process: Pin the target stack in get_wchan()
x86/dumpstack: Pin the target stack when dumping it
kthread: Pin the stack via try_get_task_stack()/put_task_stack() in to_live_kthread() function
sched/core: Add try_get_task_stack() and put_task_stack()
x86/entry/64: Fix a minor comment rebase error
iommu/amd: Don't put completion-wait semaphore on stack
...
Pull x86 apic updates from Ingo Molnar:
"The main changes are:
- Persistent CPU/node numbering across CPU hotplug/unplug events.
This is a pretty involved series of changes that first fetches all
the information during bootup and then uses it for the various
hotplug/unplug methods. (Gu Zheng, Dou Liyang)
- IO-APIC hot-add/remove fixes and enhancements. (Rui Wang)
- ... various fixes, cleanups and enhancements"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86/apic: Fix silent & fatal merge conflict in __generic_processor_info()
acpi: Fix broken error check in map_processor()
acpi: Validate processor id when mapping the processor
acpi: Provide mechanism to validate processors in the ACPI tables
x86/acpi: Set persistent cpuid <-> nodeid mapping when booting
x86/acpi: Enable MADT APIs to return disabled apicids
x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping
x86/acpi: Enable acpi to register all possible cpus at boot time
x86/numa: Online memory-less nodes at boot time
x86/apic: Get rid of apic_version[] array
x86/apic: Order irq_enter/exit() calls correctly vs. ack_APIC_irq()
x86/ioapic: Ignore root bridges without a companion ACPI device
x86/apic: Update comment about disabling processor focus
x86/smpboot: Check APIC ID before setting up default routing
x86/ioapic: Fix IOAPIC failing to request resource
x86/ioapic: Fix lost IOAPIC resource after hot-removal and hotadd
x86/ioapic: Fix setup_res() failing to get resource
x86/ioapic: Support hot-removal of IOAPICs present during boot
x86/ioapic: Change prototype of acpi_ioapic_add()
x86/apic, ACPI: Fix incorrect assignment when handling apic/x2apic entries
...
Pull RAS updates from Ingo Molnar:
"The main changes were:
- Lots of enhancements for AMD SMCA (Scalable MCA
features/extensions) systems: extract, decode and print more
hardware error information and add matching support on the
injection/testing side as well. (Yazn Ghannam)
- Various MCE handling improvements on modern Intel Xeons. (Tony
Luck)
- Plus misc fixes and enhancements"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/RAS/mce_amd_inj: Remove debugfs dir recursively on exit
x86/RAS/mce_amd_inj: Fix signed wrap around when decrementing index 'i'
x86/RAS/mce_amd_inj: Fix some W= warnings
x86/MCE/AMD, EDAC: Handle reserved bank 4 on Fam17h properly
x86/mce/AMD: Extract the error address on SMCA systems
x86/mce, EDAC/mce_amd: Print MCA_SYND and MCA_IPID during MCE on SMCA systems
x86/mce/AMD: Save MCA_IPID in MCE struct on SMCA systems
x86/mce/AMD: Ensure the deferred error interrupt is of type APIC on SMCA systems
x86/mce/AMD: Update sysfs bank names for SMCA systems
x86/mce/AMD, EDAC/mce_amd: Define and use tables for known SMCA IP types
EDAC/mce_amd: Use SMCA prefix for error descriptions arrays
EDAC/mce_amd: Add missing SMCA error descriptions
x86/mce/AMD: Read MSRs on the CPU allocating the threshold blocks
x86/RAS: Add syndrome support to mce_amd_inj
EDAC/mce_amd: Print syndrome register value on SMCA systems
x86/mce: Add support for new MCA_SYND register
x86/mce/AMD: Use msr_ops.misc() in allocate_threshold_blocks()
x86/mce: Drop X86_FEATURE_MCE_RECOVERY and the related model string test
x86/mce: Improve memcpy_mcsafe()
x86/mce: Add PCI quirks to identify Xeons with machine check recovery
...
Pull perf updates from Ingo Molnar:
"The main kernel side changes were:
- uprobes enhancements (Masami Hiramatsu)
- Uncore group events enhancements (David Carrillo-Cisneros)
- x86 Intel: Add support for Skylake server uncore PMUs (Kan Liang)
- x86 Intel: LBR cleanups and enhancements, for better branch
annotation tracking (Peter Zijlstra)
- x86 Intel: Add support for PTWRITE and power event tracing
(Alexander Shishkin)
- ... various fixes, cleanups and smaller enhancements.
Lots of tooling changes - a couple of highlights:
- Support event group view with hierarchy mode in 'perf top' and
'perf report' (Namhyung Kim)
e.g.:
$ perf record -e '{cycles,instructions}' make
$ perf report --hierarchy --stdio
...
# Overhead Command / Shared Object / Symbol
# ...................... ..................................
...
25.74% 27.18%sh
19.96% 24.14%libc-2.24.so
9.55% 14.64%[.] __strcmp_sse2
1.54% 0.00%[.] __tfind
1.07% 1.13%[.] _int_malloc
0.95% 0.00%[.] __strchr_sse2
0.89% 1.39%[.] __tsearch
0.76% 0.00%[.] strlen
- Add branch stack / basic block info to 'perf annotate --stdio',
where for each branch, we add an asm comment after the instruction
with information on how often it was taken and predicted. See
example with color output at:
http://vger.kernel.org/~acme/perf/annotate_basic_blocks.png
(Peter Zijlstra)
- Add support for using symbols in address filters with Intel PT and
ARM CoreSight (hardware assisted tracing facilities) (Adrian
Hunter, Mathieu Poirier)
- Add support for interacting with Coresight PMU ETMs/PTMs, that are
IP blocks to perform hardware assisted tracing on a ARM CPU core
(Mathieu Poirier)
- Support generating cross arch probes, i.e. if you specify a vmlinux
file for different arch than the one in the host machine,
$ perf probe --definition function_name args
will generate the probe definition string needed to append to the
target machine /sys/kernel/debug/tracing/kprobes_events file, using
scripting (Masami Hiramatsu).
- Allow configuring the default 'perf report -s' sort order in
~/.perfconfig, for instance, "sym,dso" may be more fitting for
kernel developers. (Arnaldo Carvalho de Melo)
- ... plus lots of other changes, refactorings, features and fixes"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (149 commits)
perf tests: Add dwarf unwind test for powerpc
perf probe: Match linkage name with mangled name
perf probe: Fix to cut off incompatible chars from group name
perf probe: Skip if the function address is 0
perf probe: Ignore the error of finding inline instance
perf intel-pt: Fix decoding when there are address filters
perf intel-pt: Enable decoder to handle TIP.PGD with missing IP
perf intel-pt: Read address filter from AUXTRACE_INFO event
perf intel-pt: Record address filter in AUXTRACE_INFO event
perf intel-pt: Add a helper function for processing AUXTRACE_INFO
perf intel-pt: Fix missing error codes processing auxtrace_info
perf intel-pt: Add support for recording the max non-turbo ratio
perf intel-pt: Fix snapshot overlap detection decoder errors
perf probe: Increase debug level of SDT debug messages
perf record: Add support for using symbols in address filters
perf symbols: Add dso__last_symbol()
perf record: Fix error paths
perf record: Rename label 'out_symbol_exit'
perf script: Fix vanished idle symbols
perf evsel: Add support for address filters
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- rwsem micro-optimizations (Davidlohr Bueso)
- Improve the implementation and optimize the performance of
percpu-rwsems. (Peter Zijlstra.)
- Convert all lglock users to better facilities such as percpu-rwsems
or percpu-spinlocks and remove lglocks. (Peter Zijlstra)
- Remove the ticket (spin)lock implementation. (Peter Zijlstra)
- Korean translation of memory-barriers.txt and related fixes to the
English document. (SeongJae Park)
- misc fixes and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/cmpxchg, locking/atomics: Remove superfluous definitions
x86, locking/spinlocks: Remove ticket (spin)lock implementation
locking/lglock: Remove lglock implementation
stop_machine: Remove stop_cpus_lock and lg_double_lock/unlock()
fs/locks: Use percpu_down_read_preempt_disable()
locking/percpu-rwsem: Add down_read_preempt_disable()
fs/locks: Replace lg_local with a per-cpu spinlock
fs/locks: Replace lg_global with a percpu-rwsem
locking/percpu-rwsem: Add DEFINE_STATIC_PERCPU_RWSEMand percpu_rwsem_assert_held()
locking/pv-qspinlock: Use cmpxchg_release() in __pv_queued_spin_unlock()
locking/rwsem, x86: Drop a bogus cc clobber
futex: Add some more function commentry
locking/hung_task: Show all locks
locking/rwsem: Scan the wait_list for readers only once
locking/rwsem: Remove a few useless comments
locking/rwsem: Return void in __rwsem_mark_wake()
locking, rcu, cgroup: Avoid synchronize_sched() in __cgroup_procs_write()
locking/Documentation: Add Korean translation
locking/Documentation: Fix a typo of example result
locking/Documentation: Fix wrong section reference
...
Pull EFI updates from Ingo Molnar:
"Main changes in this cycle were:
- Refactor the EFI memory map code into architecture neutral files
and allow drivers to permanently reserve EFI boot services regions
on x86, as well as ARM/arm64. (Matt Fleming)
- Add ARM support for the EFI ESRT driver. (Ard Biesheuvel)
- Make the EFI runtime services and efivar API interruptible by
swapping spinlocks for semaphores. (Sylvain Chouleur)
- Provide the EFI identity mapping for kexec which allows kexec to
work on SGI/UV platforms with requiring the "noefi" kernel command
line parameter. (Alex Thorlton)
- Add debugfs node to dump EFI page tables on arm64. (Ard Biesheuvel)
- Merge the EFI test driver being carried out of tree until now in
the FWTS project. (Ivan Hu)
- Expand the list of flags for classifying EFI regions as "RAM" on
arm64 so we align with the UEFI spec. (Ard Biesheuvel)
- Optimise out the EFI mixed mode if it's unsupported (CONFIG_X86_32)
or disabled (CONFIG_EFI_MIXED=n) and switch the early EFI boot
services function table for direct calls, alleviating us from
having to maintain the custom function table. (Lukas Wunner)
- Miscellaneous cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
x86/efi: Round EFI memmap reservations to EFI_PAGE_SIZE
x86/efi: Allow invocation of arbitrary boot services
x86/efi: Optimize away setup_gop32/64 if unused
x86/efi: Use kmalloc_array() in efi_call_phys_prolog()
efi/arm64: Treat regions with WT/WC set but WB cleared as memory
efi: Add efi_test driver for exporting UEFI runtime service interfaces
x86/efi: Defer efi_esrt_init until after memblock_x86_fill
efi/arm64: Add debugfs node to dump UEFI runtime page tables
x86/efi: Remove unused find_bits() function
fs/efivarfs: Fix double kfree() in error path
x86/efi: Map in physical addresses in efi_map_region_fixed
lib/ucs2_string: Speed up ucs2_utf8size()
firmware-gsmi: Delete an unnecessary check before the function call "dma_pool_destroy"
x86/efi: Initialize status to ensure garbage is not returned on small size
efi: Replace runtime services spinlock with semaphore
efi: Don't use spinlocks for efi vars
efi: Use a file local lock for efivars
efi/arm*: esrt: Add missing call to efi_esrt_init()
efi/esrt: Use memremap not ioremap to access ESRT table in memory
x86/efi-bgrt: Use efi_mem_reserve() to avoid copying image data
...
Pull core SMP updates from Ingo Molnar:
"Two main change is generic vCPU pinning and physical CPU SMP-call
support, for Xen to be able to perform certain calls on specific
physical CPUs - by Juergen Gross"
* 'core-smp-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp: Allocate smp_call_on_cpu() workqueue on stack too
hwmon: Use smp_call_on_cpu() for dell-smm i8k
dcdbas: Make use of smp_call_on_cpu()
xen: Add xen_pin_vcpu() to support calling functions on a dedicated pCPU
smp: Add function to execute a function synchronously on a CPU
virt, sched: Add generic vCPU pinning support
xen: Sync xen header
- Update of the ACPICA code in the kernel to upstream revision 20160831 with
the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table loading.
* Fixes for issues related to so-called module-level code (MLC), that is
AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the Windows
behavior.
* GAS (Generic Address Structure) support fix related to 32-bit FADT
addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new GPE
masking mechanism in ACPICA) and issues related to table loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action Table),
needed on some platforms to replace the iTCO watchdog that doesn't work there
and related updates of the intel_pmc_ipc, i2c/i801 and MFD/lcp_ich drivers
(Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects during
device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86 SoC drivers
and a 8250_dw driver quirk for the APM X-Gene SoC (Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of local
strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel, Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on systems
booting wth ACPI on platforms with a GIC interrupt controller model
fixing the discrepancy between the specification and HW behavior (Lorenzo
Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC driver and
update of that driver to make it cope with the cases when the EC device
defined in the ECDT has to be used throughout the entire system life cycle
(Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent over the
PCC channel (to reduce overhead), to support the fixed functional hardware
(FFH) CPPC registers access type, to notify the mailbox framework about TX
completions when the interrupt flag is set for the PCC mailbox, and to
support HW-Reduced Communication Subspace type 2 (Ashwin Chaugule, Prashanth
Prakash, Srinivas Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the handling of
laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv Zheng).
- Assorted cleanups of the ACPI table parsing code and the x86-specific ACPI
code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei Yongjun).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=xDOQ
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"First off, the ACPICA code in the kernel is updated to upstream
revision 20160831 that brings in a few bug fixes and cleanups. In
particular, it is possible to mask GPEs now (and the sysfs interface
for GPE control is fixed on top of that), problems related to the
table loading mechanism are fixed and all code related to FADT version
2 (which has never been part of the ACPI specification) is dropped.
On the new features front, there is a new watchdog driver based on the
ACPI WDAT (ACPI Watchdog Action Table), needed on some platforms to
replace the iTCO watchdog that doesn't work there, and some UART
devices get new definitions of built-in properties (to be accessed via
the generic device properties API).
Also, included is a fix for an ACPI-related PCI resorces allocation
issue and a few problems in the EC driver and in the button and
battery drivers are fixed.
In addition to that, the ACPI CPPC library is updated to make batching
of requests sent over the PCC channel possible (which reduces the PCC
usage overhead substantially in some cases) and to support functional
fixed hardware (FFH) type of CPPC registers access (which will allow
CPPC to be used on x86 too in the future).
As usual, there are some assorted fixes and cleanups too.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20160831 with the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table
loading.
* Fixes for issues related to so-called module-level code (MLC),
that is AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the
Windows behavior.
* GAS (Generic Address Structure) support fix related to 32-bit
FADT addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new
GPE masking mechanism in ACPICA) and issues related to table
loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action
Table), needed on some platforms to replace the iTCO watchdog that
doesn't work there and related updates of the intel_pmc_ipc,
i2c/i801 and MFD/lcp_ich drivers (Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects
during device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86
SoC drivers and a 8250_dw driver quirk for the APM X-Gene SoC
(Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of
local strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel,
Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on
systems booting wth ACPI on platforms with a GIC interrupt
controller model fixing the discrepancy between the specification
and HW behavior (Lorenzo Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC
driver and update of that driver to make it cope with the cases
when the EC device defined in the ECDT has to be used throughout
the entire system life cycle (Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent
over the PCC channel (to reduce overhead), to support the fixed
functional hardware (FFH) CPPC registers access type, to notify the
mailbox framework about TX completions when the interrupt flag is
set for the PCC mailbox, and to support HW-Reduced Communication
Subspace type 2 (Ashwin Chaugule, Prashanth Prakash, Srinivas
Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the
handling of laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv
Zheng).
- Assorted cleanups of the ACPI table parsing code and the
x86-specific ACPI code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei
Yongjun)"
* tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (98 commits)
ACPI / documentation: Use recommended name in GPIO property names
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / bus: Adjust ACPI subsystem initialization for new table loading mode
ACPICA: Parser: Fix a regression in LoadTable support
ACPICA: Tables: Fix "UNLOAD" code path lock issues
ACPI / watchdog: Add support for WDAT hardware watchdog
ACPI / platform: Pay attention to parent device's resources
PCI: Add pci_find_resource()
ACPI / CPPC: Support PCC with interrupt flag
ACPI / sysfs: Update sysfs signature handling code
ACPI / sysfs: Fix an issue for LoadTable opcode
ACPICA: Tables: Fix a regression in acpi_tb_find_table()
ACPI / tables: Remove duplicated include from tables.c
ACPI / APD: constify local structures
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
...
- Add a mechanism for passing hints from the scheduler to cpufreq governors
via their utilization update callbacks and use it to introduce "IOwait
boosting" into the schedutil governor and intel_pstate that will make them
boost performance if the enqueued task was previously waiting on I/O
(Rafael Wysocki).
- Fix a schedutil governor problem that causes it to overestimate utilization
if SMT is in use (Steve Muckle).
- Update defconfigs trying to use the schedutil governor as a module which is
not possible any more (Javier Martinez Canillas).
- Update the intel_pstate's pstate_sample tracepoint to take "IOwait boosting"
into account (Srinivas Pandruvada).
- Fix a problem in the cpufreq core causing it to mishandle the initialization
of CPUs registered after the cpufreq driver (Viresh Kumar, Rafael Wysocki).
- Make the cpufreq-dt driver support per-policy governor tunables, clean it
up and update its Kconfig description (Viresh Kumar).
- Add support for more ARM platforms to the cpufreq-dt driver (Chanwoo Choi,
Dave Gerlach, Geert Uytterhoeven).
- Make the cpufreq CPPC driver report frequencies in KHz to avoid user space
compatiblility issues (Al Stone, Hoan Tran).
- Clean up a few cpufreq drivers (st, kirkwood, SCPI) a bit (Colin Ian King,
Markus Elfring).
- Constify some local structures in the intel_pstate driver (Julia Lawall).
- Add a Documentation/cpu-freq/ entry to MAINTAINERS (Jean Delvare).
- Add support for PM domain removal to the generic power domains (genpd)
framework, add new DT helper functions to it and make it always enable
debugfs support if available (Jon Hunter, Tomeu Vizoso).
- Clean up the generic power domains (genpd) framework and make it avoid
measuring power-on and power-off latencies during system-wide PM transitions
(Ulf Hansson).
- Add support for the RockChip DFI controller and the rk3399 DMC to the
devfreq framework (Lin Huang, Axel Lin, Arnd Bergmann).
- Add COMPILE_TEST to the devfreq framework (Krzysztof Kozlowski, Stephen
Rothwell).
- Fix a minor issue in the exynos-ppmu devfreq driver and fix up devfreq
Kconfig indentation style (Wei Yongjun, Jisheng Zhang).
- Fix the system suspend interface to make suspend-to-idle work if platform
suspend operations have not been registered (Sudeep Holla).
- Make it possible to use hibernation with PAGE_POISONING_ZERO enabled
(Anisse Astier).
- Increas the default timeout of the system suspend/resume watchdog and make it
depend on EXPERT (Chen Yu).
- Make the operating performance points (OPP) framework avoid using OPPs that
aren't supported by the platform and fix a build warning in it (Dave Gerlach,
Arnd Bergmann).
- Fix the ARM cpuidle driver's return value (Christophe Jaillet).
- Make the SmartReflex AVS (Adaptive Voltage Scaling) driver use more common
logging style (Joe Perches).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=NYkv
-----END PGP SIGNATURE-----
Merge tag 'pm-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Traditionally, cpufreq is the area with the greatest number of
changes, but there are fewer of them than last time. There also is
some activity in the generic power domains and the devfreq frameworks,
a couple of system suspend and hibernation fixes and some assorted
changes in other places.
One new feature is the cpufreq change to allow the scheduler to pass
hints to the governors' utilization update callbacks and some code
rework based on that. Another one is the support for domain removal in
the generic power domains framework. Also it is now possible to use
hibernation with PAGE_POISONING_ZERO enabled and devfreq supports the
RockChip DFI controller and the rk3399 DMC.
The rest of the changes is mostly fixes and cleanups in a number of
places.
Specifics:
- Add a mechanism for passing hints from the scheduler to cpufreq
governors via their utilization update callbacks and use it to
introduce "IOwait boosting" into the schedutil governor and
intel_pstate that will make them boost performance if the enqueued
task was previously waiting on I/O (Rafael Wysocki).
- Fix a schedutil governor problem that causes it to overestimate
utilization if SMT is in use (Steve Muckle).
- Update defconfigs trying to use the schedutil governor as a module
which is not possible any more (Javier Martinez Canillas).
- Update the intel_pstate's pstate_sample tracepoint to take "IOwait
boosting" into account (Srinivas Pandruvada).
- Fix a problem in the cpufreq core causing it to mishandle the
initialization of CPUs registered after the cpufreq driver (Viresh
Kumar, Rafael Wysocki).
- Make the cpufreq-dt driver support per-policy governor tunables,
clean it up and update its Kconfig description (Viresh Kumar).
- Add support for more ARM platforms to the cpufreq-dt driver
(Chanwoo Choi, Dave Gerlach, Geert Uytterhoeven).
- Make the cpufreq CPPC driver report frequencies in KHz to avoid
user space compatiblility issues (Al Stone, Hoan Tran).
- Clean up a few cpufreq drivers (st, kirkwood, SCPI) a bit (Colin
Ian King, Markus Elfring).
- Constify some local structures in the intel_pstate driver (Julia
Lawall).
- Add a Documentation/cpu-freq/ entry to MAINTAINERS (Jean Delvare).
- Add support for PM domain removal to the generic power domains
(genpd) framework, add new DT helper functions to it and make it
always enable debugfs support if available (Jon Hunter, Tomeu
Vizoso).
- Clean up the generic power domains (genpd) framework and make it
avoid measuring power-on and power-off latencies during system-wide
PM transitions (Ulf Hansson).
- Add support for the RockChip DFI controller and the rk3399 DMC to
the devfreq framework (Lin Huang, Axel Lin, Arnd Bergmann).
- Add COMPILE_TEST to the devfreq framework (Krzysztof Kozlowski,
Stephen Rothwell).
- Fix a minor issue in the exynos-ppmu devfreq driver and fix up
devfreq Kconfig indentation style (Wei Yongjun, Jisheng Zhang).
- Fix the system suspend interface to make suspend-to-idle work if
platform suspend operations have not been registered (Sudeep
Holla).
- Make it possible to use hibernation with PAGE_POISONING_ZERO
enabled (Anisse Astier).
- Increas the default timeout of the system suspend/resume watchdog
and make it depend on EXPERT (Chen Yu).
- Make the operating performance points (OPP) framework avoid using
OPPs that aren't supported by the platform and fix a build warning
in it (Dave Gerlach, Arnd Bergmann).
- Fix the ARM cpuidle driver's return value (Christophe Jaillet).
- Make the SmartReflex AVS (Adaptive Voltage Scaling) driver use more
common logging style (Joe Perches)"
* tag 'pm-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (58 commits)
PM / OPP: Don't support OPP if it provides supported-hw but platform does not
cpufreq: st: add missing \n to end of dev_err message
cpufreq: kirkwood: add missing \n to end of dev_err messages
PM / Domains: Rename pm_genpd_sync_poweron|poweroff()
PM / Domains: Don't measure latency of ->power_on|off() during system PM
PM / Domains: Remove redundant system PM callbacks
PM / Domains: Simplify detaching a device from its genpd
PM / devfreq: rk3399_dmc: Remove explictly regulator_put call in .remove
PM / devfreq: rockchip: add PM_DEVFREQ_EVENT dependency
PM / OPP: avoid maybe-uninitialized warning
PM / Domains: Allow holes in genpd_data.domains array
cpufreq: CPPC: Avoid overflow when calculating desired_perf
cpufreq: ti: Use generic platdev driver
cpufreq: intel_pstate: Add io_boost trace
partial revert of "PM / devfreq: Add COMPILE_TEST for build coverage"
cpufreq: intel_pstate: Use IOWAIT flag in Atom algorithm
cpufreq: schedutil: Add iowait boosting
cpufreq / sched: SCHED_CPUFREQ_IOWAIT flag to indicate iowait condition
PM / Domains: Add support for removing nested PM domains by provider
PM / Domains: Add support for removing PM domains
...
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJX7k31AAoJELescNyEwWM0XX0H/iOaWCfKlWOhvBsStGUCsLrK
XryTzQT2KjdnLKf3jwP+1ateCuBR5ROurYxoDCX5/7mD63c5KiI338Vbv61a1lE1
AAwjt1stmQVUg/j+kqnuQwB/0DYg+2C8se3D3q5Iyn7zc19cDZJEGcBHNrvLMufc
XgHrgHgl/rzBDDlHJXleknDFge/MfhU5/Q1vJMRRb4JYrpAtmIokzCO75CYMRcCT
ND2QbmppKtsyuFPGUTVbAFzJlP6dGKb3eruYta7/ct5d0pJQxav3u98D2yWGfjdM
YaYq1EmX5Pol7rWumqLtk0+mA9yCFcKLLc+PrJu20Vx0UkvOq8G8Xt70sHNvZU8=
=gdPM
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"It's a bit all over the place this time with no "killer feature" to
speak of. Support for mismatched cache line sizes should help people
seeing whacky JIT failures on some SoCs, and the big.LITTLE perf
updates have been a long time coming, but a lot of the changes here
are cleanups.
We stray outside arch/arm64 in a few areas: the arch/arm/ arch_timer
workaround is acked by Russell, the DT/OF bits are acked by Rob, the
arch_timer clocksource changes acked by Marc, CPU hotplug by tglx and
jump_label by Peter (all CC'd).
Summary:
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (100 commits)
arm64: tlbflush.h: add __tlbi() macro
arm64: Kconfig: remove SMP dependence for NUMA
arm64: Kconfig: select OF/ACPI_NUMA under NUMA config
arm64: fix dump_backtrace/unwind_frame with NULL tsk
arm/arm64: arch_timer: Use archdata to indicate vdso suitability
arm64: arch_timer: Work around QorIQ Erratum A-008585
arm64: arch_timer: Add device tree binding for A-008585 erratum
arm64: Correctly bounds check virt_addr_valid
arm64: migrate exception table users off module.h and onto extable.h
arm64: pmu: Hoist pmu platform device name
arm64: pmu: Probe default hw/cache counters
arm64: pmu: add fallback probe table
MAINTAINERS: Update ARM PMU PROFILING AND DEBUGGING entry
arm64: Improve kprobes test for atomic sequence
arm64/kvm: use alternative auto-nop
arm64: use alternative auto-nop
arm64: alternative: add auto-nop infrastructure
arm64: lse: convert lse alternatives NOP padding to use __nops
arm64: barriers: introduce nops and __nops macros for NOP sequences
arm64: sysreg: replace open-coded mrs_s/msr_s with {read,write}_sysreg_s
...
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
One uses "print_modules" so that prevents us removing module.h in
that case, however.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
The change adds a new device node with description of generic SRAM
on-chip memory found on NXP LPC32xx SoC series and connected to AHB
matrix slave port 3.
Note that NXP LPC3220 SoC has 128KiB of SRAM memory, the other
LPC3230, LPC3240 and LPC3250 SoCs all have 256KiB SRAM space,
in the shared DTSI file this change specifies 128KiB SRAM size.
Also it's worth to mention that the SRAM area contains of 64KiB banks,
2 banks on LPC3220 and 4 banks on the other SoCs from the series, and
all SRAM banks but the first one have independent power controls,
the description of this feature will be added with the introduction of
power domains for the SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"Three relatively small fixes for ARM:
- Roger noticed that dma_max_pfn() was calculating the upper limit
wrongly, by adding the PFN offset of memory twice.
- A fix from Robin to correct parsing of MPIDR values when the
address size is larger than one BE32 unit.
- A fix from Srinivas to ensure that we do not rely on the boot
loader (or previous Linux kernel) setting the translation table
base register a certain way in the decompressor, which can lead to
crashes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
ARM: 8617/1: dma: fix dma_max_pfn()
ARM: 8616/1: dt: Respect property size when parsing CPUs
If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.
The commit dbece45894 ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.
Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.
Fixes: dbece45894 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull x86 fixes from Thomas Gleixner:
"The last regression fixes for 4.8 final:
- Two patches addressing the fallout of the CR4 optimizations which
caused CR4-less machines to fail.
- Fix the VDSO build on big endian machines
- Take care of FPU initialization if no CPUID is available otherwise
task struct size ends up being zero
- Fix up context tracking in case load_gs_index fails"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
x86/init: Fix cr4_init_shadow() on CR4-less machines
The driver does not handle endianness properly when loading the input
data.
Signed-off-by: Marcelo Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* pm-cpufreq: (24 commits)
cpufreq: st: add missing \n to end of dev_err message
cpufreq: kirkwood: add missing \n to end of dev_err messages
cpufreq: CPPC: Avoid overflow when calculating desired_perf
cpufreq: ti: Use generic platdev driver
cpufreq: intel_pstate: Add io_boost trace
cpufreq: intel_pstate: Use IOWAIT flag in Atom algorithm
cpufreq: schedutil: Add iowait boosting
cpufreq / sched: SCHED_CPUFREQ_IOWAIT flag to indicate iowait condition
cpufreq: CPPC: Force reporting values in KHz to fix user space interface
cpufreq: create link to policy only for registered CPUs
intel_pstate: constify local structures
cpufreq: dt: Support governor tunables per policy
cpufreq: dt: Update kconfig description
cpufreq: dt: Remove unused code
MAINTAINERS: Add Documentation/cpu-freq/
cpufreq: dt: Add support for r8a7792
cpufreq / sched: ignore SMT when determining max cpu capacity
cpufreq: Drop unnecessary check from cpufreq_policy_alloc()
ARM: multi_v7_defconfig: Don't attempt to enable schedutil governor as module
ARM: exynos_defconfig: Don't attempt to enable schedutil governor as module
...
When discovering the number of VPEs per core, smp_num_siblings will be
incorrect for kernels built without support for the MIPS MultiThreading
(MT) ASE running on systems which implement said ASE. This leads to
accesses to VPEs in secondary cores being performed incorrectly since
mips_cm_vp_id calculates the wrong ID to write to the local "other"
registers. Fix this by examining the number of VPEs in the core as
reported by the CM.
This patch presumes that the number of VPEs will be the same in each
core of the system. As this path only applies to systems with CM version
2.5 or lower, and this property is true of all such known systems, this
is likely to be fine but is described in a comment for good measure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* acpi-x86:
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
* acpi-cppc:
ACPI / CPPC: Support PCC with interrupt flag
ACPI / CPPC: Add prefix cppc to cpudata structure name
ACPI / CPPC: Add support for functional fixed hardware address
ACPI / CPPC: Don't return on CPPC probe failure
ACPI / CPPC: Allow build with ACPI_CPU_FREQ_PSS config
ACPI / CPPC: check for error bit in PCC status field
ACPI / CPPC: move all PCC related information into pcc_data
ACPI / CPPC: add sysfs support to compute delivered performance
ACPI / CPPC: set a non-zero value for transition_latency
ACPI / CPPC: support for batching CPPC requests
ACPI / CPPC: acquire pcc_lock only while accessing PCC subspace
ACPI / CPPC: restructure read/writes for efficient sys mapped reg ops
mailbox: pcc: Support HW-Reduced Communication Subspace type 2
* acpi-soc:
ACPI / APD: constify local structures
ACPI / APD: Add device HID for Vulcan SPI controller
Commit d9676fa152 ("ARCv2: Enable LOCKDEP"), changed
local_save_flags() to not return raw STATUS32 but encoded in the form
such that it could be fed directly to CLRI/SETI instructions.
However the STATUS32.E[] was not captured correctly as it corresponds to
bits [4:1] in the register and not [3:0]
Fixes: d9676fa152 ("ARCv2: Enable LOCKDEP")
Cc: Evgeny Voevodin <evgeny.voevodin@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Seem like values assigned as absolute number and not and
shift value, i.e. should be 0 for one node (2^0) and 1 for
couple of nodes (2^1)
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In the end of "arc_init_IRQ" STATUS32.IE flag is going to be affected by
"flag" instruction but "flag" never touches IE flag on ARCv2. So "kflag"
instruction must be used instead of "flag".
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Cc: stable@vger.kernel.org #4.2+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to keep the .exit.* sections as linker would fail in final link
due to references from .debug_frame which itself could not be discardrd
due to the forced "write,alloc" attributes for it.
| LD init/built-in.o
| `.exit.text' referenced in section `.debug_frame' of arch/arc/built-in.o: defined in discarded section `.exit.text' of arch/arc/built-in.o
| Makefile:949: recipe for target 'vmlinux' failed
With .debug_frame now retired, this hack is no longer needed.
kernel binary is now a little bit smaller as well.
closes STAR 9000549913
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This uses a new set of annoations viz. ENTRY_CFI/END_CFI to enabel cfi
ops generation.
Note that we didn't change the normal ENTRY/EXIT as we don't actually
want unwind info in the trap/exception/interrutp handlers which use
these, as unwinder then gets confused (it keeps recursing vs. stopping).
Semantically these are leaf routines and unwinding should stop when it
hits those routines.
Before
------
28.52% 1.19% 9929 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--8.95%--EV_Trap
| --8.25%--sys_write
| |--3.93%--sock_write_iter
...
|--2.62%--memset <==== [LEAF entry as no unwind info]
^^^^^^
After
-----
29.46% 1.24% 13622 hackbench libuClibc-1.0.17.so [.] __write_nocancel
|
---__write_nocancel
|--9.31%--EV_Trap
| --8.62%--sys_write
| |--4.17%--sock_write_iter
...
|--6.19%--sys_write
| --6.19%--sock_write_iter
| unix_stream_sendmsg
| |--1.62%--sock_alloc_send_pskb
| |--0.89%--sock_def_readable
| |--0.88%--_raw_spin_unlock_irqrestore
| |--0.69%--memset
| | ^^^^^^ <==== [now in proper callframe]
| |
| --0.52%--skb_copy_datagram_from_iter
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
1. detect whether binutils supports the cfi pseudo ops
2. define conditional macros to generate the ops
3. define new ENTRY_CFI/END_CFI to annotate hand asm code.
- Needed because we don't want to emit dwarf info in general ENTRY/END
used by lowest level trap/exception/interrutp handlers as unwinder
gets confused trying to unwind out of them. We want unwinder to
instead stop when it hits onfo those routines
- These provide minimal start/end cfi ops assuming routine doesn't
touch stack memory/regs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This essentially removes ENTRY() assembler annotation for this symbol
since it didn't have a pairing END()
This in ahead of introducing cfi pseudo ops in ENTRY/END which expects
paired cfi_startproc/cfi_endproc
| ../arch/arc/kernel/entry.S: Assembler messages:
| ../arch/arc/kernel/entry.S:270: Error: previous CFI entry not closed (missing .cfi_endproc)
| ../scripts/Makefile.build:326: recipe for target 'arch/arc/kernel/entry-arcv2.o' failed
| make[4]: *** [arch/arc/kernel/entry-arcv2.o] Error 1
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In .debug_frame based unwinding regime, we used to force -gdwarf-2 since
kernel unwinder only claimed to handle dwarf 2. This changed since commit
6d0d506012 ("ARC: dw2 unwind: Don't bail for CIE.version != 1")
which added some support beyond dwarf 2, atleast to handle CIE != 1
The ill-effect of -gdwarf-2 is that it forces generation of .debug_*
sections, which bloats loadable modules .ko files. For the curious, this
doesn't affect vmlinx binary since linker script discards .debug_* but
same discard is not yet implemented for modules.
So it seems we can drop the -gdwarf-2 toggle, which should not be needed
anyways given that we now use .eh_frame based unwinding.
I've verified using GNU 2016.09-engo10 that the actual unwind info is
not different with or w/o this toggle - but the debug_* sections are
gone for good.
before
-----
arc-linux-readelf -S q_proc.ko-unwinding-1-eh_frame-switch | grep debug
[15] .debug_info PROGBITS 00000000 000300 00d08d 00 0 0 1
[16] .rela.debug_info RELA 00000000 0162a0 008844 0c I 29 15 4
[17] .debug_abbrev PROGBITS 00000000 00d38d 0005f8 00 0 0 1
[18] .debug_loc PROGBITS 00000000 00d985 000070 00 0 0 1
[19] .rela.debug_loc RELA 00000000 01eae4 0000c0 0c I 29 18 4
[20] .debug_aranges PROGBITS 00000000 00d9f5 000040 00 0 0 1
[21] .rela.debug_arang RELA 00000000 01eba4 000030 0c I 29 20 4
[22] .debug_ranges PROGBITS 00000000 00da35 000018 00 0 0 1
[23] .rela.debug_range RELA 00000000 01ebd4 000030 0c I 29 22 4
[24] .debug_line PROGBITS 00000000 00da4d 000b5b 00 0 0 1
[25] .rela.debug_line RELA 00000000 01ec04 0000cc 0c I 29 24 4
[26] .debug_str PROGBITS 00000000 00e5a8 007831 01 MS 0 0 1
after
----
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
So finally after almost 8 years of dealing with .debug_frame, we are
finally switching to .eh_frame. The reason being stripped kernel
binaries had non-functional unwinder as .debug_frame was gone.
Also, in general .eh_frame seems more common way of doing unwinding.
This also folds a revert of f52e126cc7 ("ARC: unwind: ensure that
.debug_frame is generated (vs. .eh_frame)") to ensure that we start
getting .eh_frame
Reported-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
We used to live with PERF_COUNT_HW_CACHE_REFERENCES and
PERF_COUNT_HW_CACHE_REFERENCES not specified on ARC.
Those events are actually aliases to 2 cache events that we do support
and so this change sets "cache-reference" and "cache-misses" events
in the same way as "L1-dcache-loads" and L1-dcache-load-misses.
And while at it adding debug info for cache events as well as doing a
subtle fix in HW events debug info - config value is much better
represented by hex so we may see not only event index but as well other
control bits set (if they exist).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Build brekeage since last changes to generic atomic operations.
Added couple of missing macros which are now mandatory
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARCv2 ISA provides 64-bit exclusive load/stores so use them to implement
the 64-bit atomics and elide the spinlock based generic 64-bit atomics
boot tested with atomic64 self-test (and GOD bless the person who wrote
them, I realized my inline assmebly is sloppy as hell)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HS release 3.0 provides for even more flexibility in specifying the
volatile address space for mapping peripherals.
With HS 2.1 @start was made flexible / programmable - with HS 3.0 even
@end can be setup (vs. fixed to 0xFFFF_FFFF before).
So add code to reflect that and while at it remove an unused struct
defintion
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The cool thing is that same kernel image can run on
- nsim OSCI simulation platform
- SDPlite FPGA setups
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As it was discussed quite some time ago (see
https://lkml.org/lkml/2015/11/5/862) it's a good practice to add
"model" property in .dts. Moreover as per ePAPR "model" property is
required and should look like "manufacturer,model" so we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This warning:
WARNING: CPU: 0 PID: 3331 at arch/x86/entry/common.c:45 enter_from_user_mode+0x32/0x50
CPU: 0 PID: 3331 Comm: ldt_gdt_64 Not tainted 4.8.0-rc7+ #13
Call Trace:
dump_stack+0x99/0xd0
__warn+0xd1/0xf0
warn_slowpath_null+0x1d/0x20
enter_from_user_mode+0x32/0x50
error_entry+0x6d/0xc0
? general_protection+0x12/0x30
? native_load_gs_index+0xd/0x20
? do_set_thread_area+0x19c/0x1f0
SyS_set_thread_area+0x24/0x30
do_int80_syscall_32+0x7c/0x220
entry_INT80_compat+0x38/0x50
... can be reproduced by running the GS testcase of the ldt_gdt test unit in
the x86 selftests.
do_int80_syscall_32() will call enter_form_user_mode() to convert context
tracking state from user state to kernel state. The load_gs_index() call
can fail with user gsbase, gsbase will be fixed up and proceed if this
happen.
However, enter_from_user_mode() will be called again in the fixed up path
though it is context tracking kernel state currently.
This patch fixes it by just fixing up gsbase and telling lockdep that IRQs
are off once load_gs_index() failed with user gsbase.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1475197266-3440-1-git-send-email-wanpeng.li@hotmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Otherwise arch_task_struct_size == 0 and we die. While we're at it,
set X86_FEATURE_ALWAYS, too.
Reported-by: David Saggiorato <david@saggiorato.net>
Tested-by: David Saggiorato <david@saggiorato.net>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: aaeb5c01c5b ("x86/fpu, sched: Introduce CONFIG_ARCH_WANTS_DYNAMIC_TASK_STRUCT and use it on x86")
Link: http://lkml.kernel.org/r/8de723afbf0811071185039f9088733188b606c9.1475103911.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ever since commit 254d1a3f02 ("xen/pv-on-hvm kexec: shutdown watches
from old kernel") using the INTx interrupt from Xen PCI platform
device for event channel notification would just lockup the guest
during bootup. postcore_initcall now calls xs_reset_watches which
will eventually try to read a value from XenStore and will get stuck
on read_reply at XenBus forever since the platform driver is not
probed yet and its INTx interrupt handler is not registered yet. That
means that the guest can not be notified at this moment of any pending
event channels and none of the per-event handlers will ever be invoked
(including the XenStore one) and the reply will never be picked up by
the kernel.
The exact stack where things get stuck during xenbus_init:
-xenbus_init
-xs_init
-xs_reset_watches
-xenbus_scanf
-xenbus_read
-xs_single
-xs_single
-xs_talkv
Vector callbacks have always been the favourite event notification
mechanism since their introduction in commit 38e20b07ef ("x86/xen:
event channels delivery on HVM.") and the vector callback feature has
always been advertised for quite some time by Xen that's why INTx was
broken for several years now without impacting anyone.
Luckily this also means that event channel notification through INTx
is basically dead-code which can be safely removed without impacting
anybody since it has been effectively disabled for more than 4 years
with nobody complaining about it (at least as far as I'm aware of).
This commit removes event channel notification through Xen PCI
platform device.
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Julien Grall <julien.grall@citrix.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ross Lagerwall <ross.lagerwall@citrix.com>
Cc: xen-devel@lists.xenproject.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
We use __read_cr4() vs __read_cr4_safe() inconsistently. On
CR4-less CPUs, all CR4 bits are effectively clear, so we can make
the code simpler and more robust by making __read_cr4() always fix
up faults on 32-bit kernels.
This may fix some bugs on old 486-like CPUs, but I don't have any
easy way to test that.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: david@saggiorato.net
Link: http://lkml.kernel.org/r/ea647033d357d9ce2ad2bbde5a631045f5052fb6.1475178370.git.luto@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need to call GET_LE to read hdr->e_type.
Fixes: 57f90c3dfc ("x86/vdso: Error out if the vDSO isn't a valid DSO")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: linux-next@vger.kernel.org
Link: http://lkml.kernel.org/r/20160929193442.GA16617@gate.crashing.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The condition for reading CR4 was wrong: there are some CPUs with
CPUID but not CR4. Rather than trying to make the condition exact,
use __read_cr4_safe().
Fixes: 18bc7bd523 ("x86/boot: Synchronize trampoline_cr4_features and mmu_cr4_features directly")
Reported-by: david@saggiorato.net
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Link: http://lkml.kernel.org/r/8c453a61c4f44ab6ff43c29780ba04835234d2e5.1475178369.git.luto@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Switch to new CPU hotplug infrastructure.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Suggested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The message is missing a \n, add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Rename the ia64 only set_curr_task() function to free up the name.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
cmpxchg contained definitions for unused (x)add_* operations, dating back
to the original ticket spinlock implementation. Nowadays these are
unused so remove them.
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Link: http://lkml.kernel.org/r/1474913478-17757-1-git-send-email-n.borisov.lkml@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds
