pci_disable_device() is called in _suspend but there's no corresponding
pci_enable_device() in _resume.
This causes "disabling already-disabled device" warning on 2nd suspend.
Add pci_enable_device() call to _resume to fix this problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tlan_reset_adapter, we disable internal PHY when an external one is used.
On cards which use internal PHY in 10 Mbps mode, we enable it later when
setting 10 Mbps mode but it does not really work (PHY fails to reset).
Leave it enabled instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a timeout to prevent infinite loop waiting for PHY to reset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the autonegotiation poll interval from 8 seconds to 2.
This greatly reduces the time needed to detect link presence,
especially on Olicom cards at 10 Mbps (two autonegoatiations required).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess printks when the link is down.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link is lost on a card which uses internal PHY for 10 Mbit speeds,
restart autonegotiation to allow switching between 10 and 100 Mbps speeds.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM.
Byte-swap the MAC address if it's located at offset 0xF8.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ethtool support to tlan driver:
- driver info - link detect (this allows NetworkManager to detect carrier)
- EEPROM read
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable old link monitoring code and modify it:
- control LINK LED
- use separate timer so it does not interfere with ACT LED
Tested with Olicom OC-2326.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olicom OC-2325 and OC-2326 ethernet cards have an activity LED but it does not
work with tlan driver as it's not enabled. Enable it.
Tested with OC-2326.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 629c9a8fd0 (drivers: net: cpsw: Add
default vlan for dual emac case also), api cpsw_add_default_vlan() also
changes the port vlan which is required to seperate the ports which results
in the following behavior
In Dual EMAC mode, when both the Etnernet connected is connected to same
switch, it creates a loop in the switch and when a broadcast packet is
received it is forwarded to the other port which stalls the whole switch
and needs a reset/power cycle to the switch to recover. So intead of using
the api, add only the default VLAN entry in dual EMAC case.
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently change the kzalloc() to devm_kzalloc() so freeing "ctlr"
here could lead to a double free.
Fixes: e194312854 ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit cd11cf5053 I accidentally
added an error message. I used it for debugging and forgot to remove
it before submitting the patch.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e194312854 (drivers: net:
davinci_cpdma: Convert kzalloc() to devm_kzalloc()) triggered
a bug in emac_probe() wherein dev member of net_device is used
for devres allocations even before it is initialized.
This patch fixes that by using the struct device in platform_device
instead.
While at it, use &pdev->dev consistently for console messages instead
of using ndev->dev for just one case and remove an unnecessary line
continuation.
Reported-by: Kevin Hilman <khilman@linaro.org>
Helped-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These should not have trailing semicolons so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert kzalloc() to devm_kzalloc().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the lone pr_err() to dev_err() call.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all pr_*() calls to dev_*() calls.
No functional changes.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM43xx phy mode selection is similar to AM33xx platform, so adding only
the compatibility string to the driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dra7xx support for selecting the phy mode which is present in control
module of dra7xx SoC
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->dev is uninitialized, initializing with pdev->dev
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).
Cc: stable <stable@vger.kernel.org> # v3.8
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f8d56d8f89 ("net:
eth: cpsw: Correctly attach to GPIO bitbang MDIO driver").
Fix potential null-pointer dereference at probe if the mdio-gpio device
has not been successfully probed yet.
The offending commit is plain wrong for a number of reasons. First of
all it accesses internal driver data of an unrelated device. Neither
does it check that the data is non-null (which it is in case the device
has not been probed yet).
Furthermore, the decision on whether to treat any driver data according
to the mdio-gpio driver's internals is made based on the node name. But
the name is not compared against "mdio" which is the normal name for the
node, but rather against "gpio" which the node does not have to be named
(and shouldn't be according to the binding documentation). [ If this
hack is to be kept out-of-tree it should at least be matching against
the compatible property. ]
Cc: Stefan Roese <sr@denx.de>
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the Annex F Time Sync explicitly for DRA7x and AM4372.
With this enabled the L2 PTP is working.
while at that rename TS_BIT8 to TS_TTL_NONZERO
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable cpts hardware time stamping for Dra7xx and AM4372.
This enables PTPv2 for DRA7xx and AM4372.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPTS refclk name is hardcoded, which makes it fail in case of DRA7x
Remove the hardcoded clock name for CPTS refclk and get the same from DT.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify IO memory mapping by using devm_ioremap_resource()
which will do all errors handling and reporting for us.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "default" pinctrl state is set by Drivers core now before
calling the driver's probe.
Hence, it's safe to drop pinctrl_pm_select_default_state() call
from Davinci mdio driver probe.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_* API for memory allocation and to get device's clock
to simplify driver's code.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpmac_config() refuses changing the base address parameter, and ignores
all other parameters, which means that it is pretty useless as it is, so
let's remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Ethernet interface is put down and up with heavy Ethernet
traffic, then there is prossibility of an interrupt waiting in irq
controller to be processed, so when the interface is brought up again
just after enable interrupt, it goes to ISR due to the previous
unhandled interrutp and in ISR napi is not scheduled as the napi
is not enabled in ndo_open which results in disabled interrupt for
CPSW and no packets are received in cpsw. So this patch moves enabling
of interupts after napi_enable and clearing CPDMA interrupts.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Ethernet interface is brought down during high Ethernet traffic,
then cpsw creates the following warn dump. When cpdma has already processed
the packet then the status will be greater than 0, so the cpsw_rx_handler
considers that the interface is up and try to resubmit one more rx buffer
to cpdma which fails as the DMA is in teardown process. This can be avoided
by checking the interface state and then process the received packet, if the
interface is down just discard and free the skb and return.
[ 2823.104591] WARNING: CPU: 0 PID: 1823 at drivers/net/ethernet/ti/cpsw.c:711 cpsw_rx_handler+0x148/0x164()
[ 2823.114654] Modules linked in:
[ 2823.117872] CPU: 0 PID: 1823 Comm: ifconfig Tainted: G W 3.14.0-11992-gf34c4a3 #11
[ 2823.126860] [<c0014b5c>] (unwind_backtrace) from [<c00117e4>] (show_stack+0x10/0x14)
[ 2823.135030] [<c00117e4>] (show_stack) from [<c0533a9c>] (dump_stack+0x80/0x9c)
[ 2823.142619] [<c0533a9c>] (dump_stack) from [<c003f0e0>] (warn_slowpath_common+0x6c/0x90)
[ 2823.151141] [<c003f0e0>] (warn_slowpath_common) from [<c003f120>] (warn_slowpath_null+0x1c/0x24)
[ 2823.160336] [<c003f120>] (warn_slowpath_null) from [<c03caeb0>] (cpsw_rx_handler+0x148/0x164)
[ 2823.169314] [<c03caeb0>] (cpsw_rx_handler) from [<c03c730c>] (__cpdma_chan_free+0x90/0xa8)
[ 2823.178028] [<c03c730c>] (__cpdma_chan_free) from [<c03c7418>] (__cpdma_chan_process+0xf4/0x134)
[ 2823.187279] [<c03c7418>] (__cpdma_chan_process) from [<c03c7560>] (cpdma_chan_stop+0xb4/0x17c)
[ 2823.196349] [<c03c7560>] (cpdma_chan_stop) from [<c03c766c>] (cpdma_ctlr_stop+0x44/0x9c)
[ 2823.204872] [<c03c766c>] (cpdma_ctlr_stop) from [<c03cb708>] (cpsw_ndo_stop+0x154/0x188)
[ 2823.213321] [<c03cb708>] (cpsw_ndo_stop) from [<c046f0ec>] (__dev_close_many+0x84/0xc8)
[ 2823.221761] [<c046f0ec>] (__dev_close_many) from [<c046f158>] (__dev_close+0x28/0x3c)
[ 2823.230012] [<c046f158>] (__dev_close) from [<c0474ca8>] (__dev_change_flags+0x88/0x160)
[ 2823.238483] [<c0474ca8>] (__dev_change_flags) from [<c0474da0>] (dev_change_flags+0x18/0x48)
[ 2823.247316] [<c0474da0>] (dev_change_flags) from [<c04d12c4>] (devinet_ioctl+0x61c/0x6e0)
[ 2823.255884] [<c04d12c4>] (devinet_ioctl) from [<c045c660>] (sock_ioctl+0x68/0x2a4)
[ 2823.263789] [<c045c660>] (sock_ioctl) from [<c0125fe4>] (do_vfs_ioctl+0x78/0x61c)
[ 2823.271629] [<c0125fe4>] (do_vfs_ioctl) from [<c01265ec>] (SyS_ioctl+0x64/0x74)
[ 2823.279284] [<c01265ec>] (SyS_ioctl) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dual EMAC works with VLAN segregation of the ports, so default vlan needs
to be added in dual EMAC case else default vlan will be tagged for all
egress packets and vlan unaware switches/servers will drop packets
from the EVM.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix build errors:
drivers/net/ethernet/ti/cpts.c:266:12: error: 'ETH_HLEN' undeclared (first use in this function)
drivers/net/ethernet/ti/cpts.c:276:23: error: 'VLAN_HLEN' undeclared (first use in this function)
Fixes: 408eccce32 ("net: ptp: move PTP classifier in its own file")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently pch_gbe, cpts, and ixp4xx_eth drivers that open-code
and reimplement a BPF classifier for the PTP protocol. Since all of them
effectively do the very same thing and load the very same PTP/BPF filter,
we can just consolidate that code by introducing ptp_classify_raw() in
the time-stamping core framework which can be used in drivers.
As drivers get initialized after bootstrapping the core networking
subsystem, they can make use of ptp_insns wrapped through
ptp_classify_raw(), which allows to simplify and remove PTP classifier
setup code in drivers.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs during the initialization in emac_dev_open() (the
driver's ndo_open function), interrupts, DMA descriptors etc. must be freed.
The current rollback code is buggy in several ways.
1) Freeing the interrupts. The current code will not free all interrupts
that were requested by the driver. Furthermore, the code tries to do a
platform_get_resource(priv->pdev, IORESOURCE_IRQ, -1) in its last
iteration.
This patch fixes these bugs.
2) Wrong order of err: and rollback: labels. If the setup of the PHY in
the code fails, the interrupts that have been requested before are
not freed:
request irq
if requesting irqs fails, goto rollback
setup phy
if phy setup fails, goto err
return 0
rollback:
free irqs
err:
This patch brings the code into the correct order.
3) The code calls napi_enable() and emac_int_enable(), but does not
undo both in case of an error.
This patch adds calls of emac_int_disable() and napi_disable() to the
rollback code.
4) RX DMA descriptors are not freed in case of an error: Right before
requesting the irqs, the function creates DMA descriptors for the
RX channel. These RX descriptors are never freed when we jump to either
rollback or err.
This patch adds code for freeing the DMA descriptors in the case of
an initialization error. This required a modification of
cpdma_ctrl_stop() in davinci_cpdma.c: We must be able to call this
function to free the DMA descriptors while the DMA channels are
in IDLE state (before cpdma_ctlr_start() was called).
Tested on a custom board with the Texas Instruments AM1808.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6892b41d97
Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date: Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api
the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.
This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.
Reported-by: Jon Ringle <jon@ringle.org>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit f280e89a (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.
[ 18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[ 19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[ 19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[ 19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using an own copy of struct net_device_stats in struct
cpsw_priv, use stats from struct net_device. Also remove the thus
unnecessary .ndo_get_stats function, as it just returns dev->stats,
which is the default.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a CPDMA RX Descriptor leak that occurs after taking
the interface down when the CPSW is in Dual MAC mode. Previously
the CPSW_ALE port was left open up which causes packets to be received
and processed by the RX interrupt handler and were passed to the
non active network interface where they were ignored.
The fix is for the slave_stop function of the selected interface
to disable the respective CPSW_ALE Port from forwarding packets. This
blocks traffic from being received on the inactive interface.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the use of a generic timestamping phy connected
to the cpsw if CPTS support is not enabled. This also adds support
of the SIOCGMIIREG and SIOCSMIIREG, and moves handling of SIOCGMIIPHY
to the generic driver.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0cd8f9cc06 ("drivers: net: cpsw:
enable promiscuous mode support")
Enable promiscuous mode support for CPSW.
Introduced a crash on an am335x based board (similiar to am335x-evm).
Reason is buggy end condition in for loop in cpsw_set_promiscious()
for (i = 0; i <= priv->data.slaves; i++)
should be
for (i = 0; i < priv->data.slaves; i++)
Fix this ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's wrong if the device tree doesn't provide a phy-mode property for
the cpsw slaves as it is documented to be required in
Documentation/devicetree/bindings/net/cpsw.txt.
Anyhow it's nice to catch that problem, still more as it used to work
without this property up to commit 388367a5a9 (drivers: net: cpsw: use
cpsw-phy-sel driver to configure phy mode) which is in v3.13-rc1.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the GPIO bitbang MDIO driver is used instead of the Davinci MDIO driver
we need to configure the phy_id string differently. Otherwise this string
looks like this "gpio.6" instead of "gpio-0" and the PHY is not found when
phy_connect() is called.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following sparse warning
davinci_mdio.c:85:27: warning: symbol 'default_pdata' was not declared. Should it be static?
Also makes the default_pdata as a constant.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During checking the interrupts with "cat /proc/interrupts", it is showing
device name as (null), this change was done with commit id aa1a15e2d where
request_irq is changed to devm_request_irq also changing the irq name from
platform device name to net device name, but the net device is not
registered at this point with the network frame work, so devm_request_irq
is called with device name as NULL, by which it is showed as "(null)" in
"cat /proc/interrupts". So this patch changes back irq name to platform
device name itself in devm_request_irq so that the device name shows as
below.
Previous to this patch
root@am335x-evm:~# cat /proc/interrupts
CPU0
28: 2265 INTC 12 edma
30: 80 INTC 14 edma_error
56: 0 INTC 40 (null)
57: 1794 INTC 41 (null)
58: 7 INTC 42 (null)
59: 0 INTC 43 (null)
With this patch
root@am335x-evm:~# cat /proc/interrupts
CPU0
28: 213 INTC 12 edma
30: 9 INTC 14 edma_error
56: 0 INTC 40 4a100000.ethernet
57: 16097 INTC 41 4a100000.ethernet
58: 11964 INTC 42 4a100000.ethernet
59: 0 INTC 43 4a100000.ethernet
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling In Band mode in 10 mbps speed.
RGMII supports 1 Gig and 100 mbps mode for Forced mode of operation.
For 10mbps mode it should be configured to in band mode so that link
status, duplexity and speed are determined from the RGMII input data
stream
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPSW and Davinci MDIO are build as modules, CPSW crashes when
accessing CPSW registers in CPSW probe. The same is working in built-in
as the CPSW clocks are enabled in Davindi MDIO probe, SO Enabling the
clocks before accessing the version register and moving out the other
register access to cpsw device open.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor fix for printk format of a phys_addr_t, and the switch of two local
functions to static since they're not used outside of the file.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silences the below warnings when building with ARM_LPAE enabled, which
gives longer dma_addr_t by default:
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
drivers/net/ethernet/ti/davinci_cpdma.c:182:3: warning: passing argument 3 of 'dma_alloc_attrs' from incompatible pointer type [enabled by default]
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'desc_phys':
drivers/net/ethernet/ti/davinci_cpdma.c:222:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/net/ethernet/ti/davinci_cpdma.c:223:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
When booted with device tree, we may still have platform data passed
as auxdata. For am3517 this is needed for passing the interrupt_enable
and interrupt_disable callbacks that access the omap system control module
registers. These callback functions will eventually go away when we have
a separate system control module driver.
Some of the things that are currently passed as platform data we don't need
to set up as device tree properties as they are always the same on am3517.
So let's use a new compatible flag for those so we can get those from
the device tree match data.
Also note that we need to fix setting of phy_dev to NULL instead of an empty
string as the code later on uses that to find the first phy on the mdio bus.
This seems to have been caused by 5d69e0076a (net: davinci_emac: switch to
new mdio).
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When only one port of the two port is pinned out, then dt probe is failing
because second port phy is not found. fixing this by checking the number of
slaves and breaking the loop.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During resume, use for_each_slave to walk the slaves of the cpsw, and
soft-reset each of them. This prevents oopses if there is only one
slave configured.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpsw_hwtstamp_ioctl() should validate all fields of hwtstamp_config,
and the hardware version, before making any changes. Currently it
sets the TX configuration before validating the rx_filter field
or that the hardware supports timestamping.
Also correct the error code for hardware versions that don't
support timestamping. ENOTSUPP is used by the NFS implementation
and is not part of userland API; we want EOPNOTSUPP (which glibc
also calls ENOTSUP, with one 'P').
Untested as I don't have a cross-compiler to hand.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFF_ALLMULTI flag is set on interface and IFF_PROMISC isn't,
emac_dev_mcast_set should only enable RX of multicasts and reset
MACHASH registers.
It does this, but afterwards it either sets up multicast MACs
filtering or disables RX of multicasts and resets MACHASH registers
again, rendering IFF_ALLMULTI flag useless.
This patch fixes emac_dev_mcast_set, so that multicast MACs filtering and
disabling of RX of multicasts are skipped when IFF_ALLMULTI flag is set.
Tested with kernel 2.6.37.
Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If interrupts happen before napi_enable was called, the driver will not
work as expected. Network transmissions are impossible in this state.
This bug can be reproduced easily by restarting the network interface in
a loop. After some time any network transmissions on the network
interface will fail.
This patch fixes the bug by enabling napi before enabling the network
interface interrupts.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/netdevice.h
net/core/sock.c
Trivial merge issues.
Removal of "extern" for functions declaration in netdevice.h
at the same time "const" was added to an argument.
Two parallel line additions in net/core/sock.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation searches the whole DT for nodes named
"slave".
This patch changes it to search only child nodes for slaves.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Phy mode can be configured via the cpsw-phy-sel driver, this patch enabled the
cpsw driver to utilise the api provided by the cpsw-phy-sel driver to configure
the phy mode.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw currently lacks code to properly set up the hardware interface
mode on AM33xx. Other platforms might be equally affected.
Usually, the bootloader will configure the control module register, so
probably that's why such support wasn't needed in the past. In suspend
mode though, this register is modified, and so it needs reprogramming
after resume.
This patch adds a new driver in which hardware interface can configure
correct register bits when the slave is opened.
The AM33xx also has a bit for each slave to configure the RMII reference
clock direction. Setting it is now supported by a per-slave DT property.
This code path introducted by this patch is currently exclusive for
am33xx and same can be extened to various platforms via the DT compatibility
property.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the allocation and error unwind paths, which
allows us to carry less information in struct cpsw_priv and reduce the
amount of jump labels in the probe functions.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed when the cpsw driver is built as module.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some phy's can be configured to enable wake on lan (e.g. at803x or marvell 88E1318S).
There is no way how to enable wol on CPSW with such connected phys. This patch
adds this support. It is provided by calling the phy's related code.
Tested on board with at8030x connected phy. Wol interrupt line is
connected to GPIO0 on am335x.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version which is present in AM43xx SoC has a minor changes and the
offsets are same as the previous version, so adding new IP version support in
the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version has a minor changes and the offsets are same as the
previous version, so adding new IP version support in the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQF_DISABLED is a no-op by now and should be
removed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for setting MAC address to cpsw device via ndo_set_mac_address
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to show CPSW hardware statistics to user via ethtool
so user can find if there were any error reported by hardware or
the system is over loaded duing high data rate transfer.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to add a newline after logging the device's MACID.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
guard the davinci_mdio_of_mtable table and davinci_mdio_probe_dt()
with CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the OF parser code, removes unnecessary checks
on of_property_read_*() and guards davinci_emac_of_match table with
CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource instead of devm_request_mem_region()/devm_ioremap()
and devm_request_irq() instead of request_irq().
This ensures more consistent error values and simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_suspend':
drivers/net/ethernet/ti/cpsw.c:1979:26: error: 'priv' undeclared (first use in this function)
drivers/net/ethernet/ti/cpsw.c:1979:26: note: each undeclared identifier is reported only once for each function it appears in
make[4]: *** [drivers/net/ethernet/ti/cpsw.o] Error 1
The compilation error was introduced by the following commit
6d3d76f (drivers: net: cpsw: fix cpsw clock gating issue across suspend/resume)
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the DMA mapping may fail the caller should check the return value.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to some hardware integration issue, CPSW sliver modules requires a
reset across suspend/resume cycle for a successful clock gating to
CPGMAC (CPSW and Davinci MDIO) in AM335x PG1.0.
This issue is fixed in PG2.x, though to support suspend/resume on PG1.0
this reset is required.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
after priv->cpts got allocated then this pointer should check to determine
if the allocation succeeded or not.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This utilize the new pinctrl core PM helpers to transition
the driver to "default" and "sleep" states.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This utilize the new pinctrl core PM helpers to transition
the driver to "default" and "sleep" states.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
was playing with suspend and run into this:
|BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891
|in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash
|6 locks held by bash/1963:
|CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50
|[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14)
|[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac)
|[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c)
|[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54)
|[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64)
|[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c)
|[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230)
|[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350)
|[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c)
|[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc)
|[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20)
|[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c)
|[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190)
|[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70)
|[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48)
I don't see a reason why the pm_runtime call must be under the lock.
Further I don't understand why this is a spinlock and not mutex.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding phy-mode support to cpsw driver and updating the cpsw binding
documentation.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional 4 bytes found in the skb is the CRC calculated by the
CPDMA hardware, check the CRC bit in CPDMA status field of
Descriptor and remove the CRC length from the skb. This extra
4 byte can be seen when capturing packets using tcpdump.
This has been tested in TI816x platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 2 places are the only matches for is_eisa in the whole tree.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In CPSW NAPI, after processing all interrupts IRQ is enabled and then book
keeping irq_enabled is updated. In random cases when a packet is transmitted
or received between processing packets and IRQ enabled, then just after
enabled IRQ and before irq_enabled is updated, ISR is called so IRQs are
not disabled as irq_enabled is still false and CPU gets locked in CPSW ISR.
By changing the sequence as update the irq_enabled and then enable IRQ
fixes the issue. This issue is not captured always as it is a timing issue
whether Tx or Rx IRQ is invoked between packet processing and enable IRQ.
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
With the commit a11fbba (net/cpsw: fix irq_disable() with threaded interrupts)
from Sebastian Siewior, a kernel warning is generated as below. This warning
is generated as the irq_enabled is not initialized for the primary interface
and in probe it is initialized for the second interface. This patch moves
irq_enabled initialization from second interface to primary interface.
[ 3.049173] net eth0: phy found : id is : 0x4dd074
[ 3.054552] net eth0: phy found : id is : 0x4dd074
[ 3.070421] ------------[ cut here ]------------
[ 3.075308] WARNING: at kernel/irq/manage.c:437 enable_irq+0x3c/0x74()
[ 3.082173] Unbalanced enable for IRQ 56
[ 3.086299] Modules linked in:
[ 3.089557] [<c001abcc>] (unwind_backtrace+0x0/0xf0) from [<c004294c>] (warn_slowpath_common+0x4c/0x68)
[ 3.099450] [<c004294c>] (warn_slowpath_common+0x4c/0x68) from [<c00429fc>] (warn_slowpath_fmt+0x30/0x40)
[ 3.109521] [<c00429fc>] (warn_slowpath_fmt+0x30/0x40) from [<c00a29fc>] (enable_irq+0x3c/0x74)
[ 3.118681] [<c00a29fc>] (enable_irq+0x3c/0x74) from [<c03a7818>] (cpsw_ndo_open+0x61c/0x684)
[ 3.127669] [<c03a7818>] (cpsw_ndo_open+0x61c/0x684) from [<c0445c08>] (__dev_open+0x9c/0xf8)
[ 3.136646] [<c0445c08>] (__dev_open+0x9c/0xf8) from [<c0445e34>] (__dev_change_flags+0x78/0x13c)
[ 3.145988] [<c0445e34>] (__dev_change_flags+0x78/0x13c) from [<c0445f64>] (dev_change_flags+0x10/0x48)
[ 3.155884] [<c0445f64>] (dev_change_flags+0x10/0x48) from [<c0736d88>] (ip_auto_config+0x198/0x111c)
[ 3.165592] [<c0736d88>] (ip_auto_config+0x198/0x111c) from [<c00086a4>] (do_one_initcall+0x34/0x180)
[ 3.175309] [<c00086a4>] (do_one_initcall+0x34/0x180) from [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8)
[ 3.185393] [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8) from [<c04f36ec>] (kernel_init+0x8/0xe4)
[ 3.194929] [<c04f36ec>] (kernel_init+0x8/0xe4) from [<c00133d0>] (ret_from_fork+0x14/0x24)
[ 3.203712] ---[ end trace d6f979da080bc391 ]---
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During high throughput it is likely that we receive both: an RX and TX
interrupt. The normal behaviour is that once we enter the ISR the
interrupts are disabled in the IRQ chip and so the ISR is invoked only
once and the interrupt line is disabled once. It will be re-enabled
after napi completes.
With threaded interrupts on the other hand the interrupt the interrupt
is disabled immediately and the ISR is marked for "later". By having TX
and RX interrupt marked pending we invoke them both and disable the
interrupt line twice. The napi callback is still executed once and so
after it completes we remain with interrupts disabled.
The initial patch simply removed the cpsw_{enable|disable}_irq() calls
and it worked well on my AM335X ES1.0 (beagle bone). On ES2.0 (beagle
bone black) it caused an never ending interrupt (even after the mask via
cpsw_intr_disable()) according to Mugunthan V N. Since I don't have the
ES2.0 and no idea what is going on this patch tracks the state of the
irq_disable() call and execute it only when not yet done.
The book keeping is done on the first struct since with dual_emac we can
have two of those and only one interrupt line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
text data bss dec hex filename
15530 92 4 15626 3d0a cpsw.o.before
15478 92 4 15574 3cd6 cpsw.o.after
52 bytes smaller, 13 for each invocation.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not clean up properly after leaving. Here is a list:
- Use unregister_netdev(). free_netdev() is good but not enough
- Use the above also on the other ndev in case of dual mac
- Free data.slave_data. The name of the strucre makes it look like
it is platform_data but it is not. It is just a trick!
- Free all irqs. Again: freeing one irq is good start, but freeing all
of them is better.
With this rmmod & modprobe of cpsw seems to work. The remaining issue
is:
|WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0x9c/0xd4()
|sysfs: cannot create duplicate filename '/devices/ocp.2/4a100000.ethernet/4a101000.mdio'
|WARNING: at lib/kobject.c:196 kobject_add_internal+0x1a4/0x1c8()
comming from of_platform_populate() and I am not sure that this belongs
here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If compiled as modules each one of these modules is missing something.
With this patch the modules are loaded on demand and don't taint the
kernel due to license issues.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that we run into OOM during the allocation of the new rx-skb we
don't get one and we have one skb less than we used to have. If this
continues to happen then we end up with no rx-skbs at all.
This patch changes the following:
- if we fail to allocate the new skb, then we treat the currently
completed skb as the new one and so drop the currently received data.
- instead of testing multiple times if the device is gone we rely one
the status field which is set to -ENOSYS in case the channel is going
down and incomplete requests are purged.
cpdma_chan_stop() removes most of the packages with -ENOSYS. The
currently active packet which is removed has the "tear down" bit set.
So if that bit is set, we send ENOSYS as well otherwise we pass the
status bits which are required to figure out which of the two possible
just finished.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp_mask argument is not used in cpdma_chan_submit() and always set
to GFP_KERNEL even in atomic sections. This patch drops it since it is
unused.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_running() reports false before the ->ndo_stop() callback is
called. That means if one executes "ifconfig down" and the system
receives an interrupt before the interrupt source has been disabled we
hang for always for two reasons:
- we never disable the interrupt source because devices claim to be
already inactive and don't feel responsible.
- since the ISR always reports IRQ_HANDLED the line is never deactivated
because it looks like the ISR feels responsible.
This patch changes the logic in the ISR a little:
- If none of the status registers reports an active source (RX or TX,
misc is ignored because it is not actived) we leave with IRQ_NONE.
- the interrupt is deactivated
- The first active network device is taken and napi is scheduled. If
none are active (a small race window between ndo_down() and the
interrupt the) then we leave and should not come back because the
source is off.
There is no need to schedule the second NAPI because both share the
same dma queue.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if during "ifconfig up" we run out of mem we continue regardless how
many skbs we got. In worst case we have zero RX skbs and can't ever
receive further packets since the RX skbs are never reallocated. If
cpdma_chan_submit() fails we even leak the skb.
This patch changes the behavior here:
If we fail to allocate an skb during bring up we don't continue and
report that error. Same goes for errors from cpdma_chan_submit().
While here I changed to __netdev_alloc_skb_ip_align() so GFP_KERNEL can
be used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__cpdma_chan_process() holds the lock with interrupts off (and its
caller as well), same goes for cpdma_ctlr_start(). With interrupts off,
jiffies will not make any progress and if the wait condition never gets
true we wait for ever.
Tgis patch adds a a simple udelay and counting down attempt.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
the work has been scheduled from interrupt, and not been
cancelled when the driver is unloaded, which doesn't remove
the work item from the global workqueue. call the
cancel_work_sync when the driver is removed (rmmod'ed).
Cc: Sriram <srk@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Vinay Hegde <vinay.hegde@ti.com>
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dual EMAC slave VLAN id must be got from slave node instead of cpsw node as
VLAN id for each slave will be different.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devres APIs where possible to simplify error handling
in driver probe.
While at it, also rename the goto targets in error path to
introduce some consistency in how they are named.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull to get the thermal netlink multicast group name fix, otherwise
the assertion added in net-next to netlink to detect that kind of bug
makes systems unbootable for some folks.
Signed-off-by: David S. Miller <davem@davemloft.net>
The error check in cpsw_probe_dt() has an '&&' where an '||' is
meant to be. This causes a NULL pointer dereference when incomplet DT
data is passed to the driver ('phy_id' property for cpsw_emac1
missing).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
emac_poll_controller() was not declared. It should be static.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary