Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements reading of the Signal Quality Index for better
cable/link troubleshooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be able
to automatically handle this issue, but we need to log it or notify user
(if possible).
With this patch, the cable will be tested on "ip l s dev .. up" attempt
and send ethnl notification to the user space.
This patch was tested with TJA1102 PHY and "ethtool --monitor" command.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial cable testing support.
This PHY needs only 100usec for this test and it is recommended to run it
before the link is up. For now, provide at least ethtool support, so it
can be tested by more developers.
This patch was tested with TJA1102 PHY with following results:
- No cable, is detected as open
- 1m cable, with no connected other end and detected as open
- a 40m cable (out of spec, max lenght should be 15m) is detected as OK.
Current patch do not provide polarity test support. This test would
indicate not proper wire connection, where "+" wire of main phy is
connected to the "-" wire of the link partner.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TJA11xx PHYs have a vendor specific Master/Slave configuration bit,
which is not compatible with IEEE 803.2-2018 spec for 100Base-T1
devices. So, provide a custom config_ange call back to solve this
problem.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detection by
compatible, on other hand we should be able to reset complete chip
before PHY1 configured it, and we need to define dependencies for proper
power management.
We can solve it by defining PHY1 as child of PHY0:
tja1102_phy0: ethernet-phy@4 {
reg = <0x4>;
interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
reset-assert-us = <20>;
reset-deassert-us = <2000>;
tja1102_phy1: ethernet-phy@5 {
reg = <0x5>;
interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
};
};
The PHY1 should be a subnode of PHY0 and registered only after PHY0 was
completely reset and initialized.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For
example PHY 1 has no PHY ID and no health monitor.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn