The INIT_MODE endpoint configuration register is only valid for TX
endpoints. Rather than writing a zero to that register for RX
endpoints, avoid writing the register at all.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_HDR_METADATA_MASK endpoint configuration register is only
valid for RX endpoints. Rather than writing a zero to that register
for TX endpoints, avoid writing the register at all.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_HOL_BLOCK_EN and INIT_HOL_BLOCK_TIMER endpoint registers
are only valid for RX endpoints.
Have ipa_endpoint_modem_hol_block_clear_all() skip writing these
registers for TX endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the "limit" local variable in ipa_endpoint_init_aggr() when
setting the aggregation size limit. Simple cleanup.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Halve the time limit used when aggregation is enabled on an RX
endpoint, to half a millisecond.
Use DIV_ROUND_CLOSEST() to compute the value that represents the
time period, to get better accuracy in the event the time limit is
not an even multiple of the granularity.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only QMAP endpoints should be configured to find a pad size field
within packet headers. They are found in the first byte of the QMAP
header (and the hardware fills only the 6 bits in that byte that
constitute the pad_len field).
The RMNet driver assumes the pad_len field is valid for received
packets, so we want to ensure the pad_len field is filled in that
case. That driver also assumes the length in the QMAP header
includes the pad bytes.
The RMNet driver does *not* pad the packets it sends, so the pad_len
field can be ignored.
Fix ipa_endpoint_init_hdr_ext() so it only marks the pad field
offset valid for QMAP RX endpoints, and in that case indicates
that the length field in the header includes the pad bytes.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upper two nibbles of the sequencer type were not used for
SDM845, and were assumed to be 0. But for SC7180 they are used, and
so they must be programmed by ipa_endpoint_init_seq(). Fix this bug.
IPA_SEQ_PKT_PROCESS_NO_DEC_NO_UCP_DMAP doesn't have a descriptive
comment, so add one.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way the mask value is programmed for QMAP RX endpoints was based
on some wrong assumptions about the way metadata containing the QMAP
mux_id value is formatted. The metadata value supplied by the
modem is *not* in QMAP format, and in fact contains the mux_id we
want in its (big endian) low-order byte. That byte must be written
by the IPA into offset 1 of the QMAP header it inserts before the
received packet.
QMAP TX endpoints *do* use a QMAP header as the metadata sent with
each packet. The modem assumes this, and based on that assumes the
mux_id is in the second byte. To match those assumptions we must
program the modem TX (QMAP) endpoint HDR register to indicate the
metadata will be found at offset 0 in the message header.
The previous configuration managed to work, but it was not working
correctly. This patch fixes a bug whose symptom was receipt of
messages containing the wrong QMAP mux_id.
In fixing this, get rid of ipa_rmnet_mux_id_metadata_mask(), which
was more or less defined so there was a separate place to explain
what was happening as we generated the mask value. Instead, put a
longer description of how this works above ipa_endpoint_init_hdr(),
and define the metadata mask to use as a simple constant.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "transactio" -> "transaction". Also an alignment correction.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building arm64 allyesconfig:
drivers/net/ipa/ipa_endpoint.c: In function 'ipa_endpoint_stop_rx_dma':
drivers/net/ipa/ipa_endpoint.c:1274:13: error: 'IPA_ENDPOINT_STOP_RX_SIZE' undeclared (first use in this function)
drivers/net/ipa/ipa_endpoint.c:1274:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ipa/ipa_endpoint.c:1289:2: error: implicit declaration of function 'ipa_cmd_dma_task_32b_addr_add' [-Werror=implicit-function-declaration]
drivers/net/ipa/ipa_endpoint.c:1291:45: error: 'ENDPOINT_STOP_DMA_TIMEOUT' undeclared (first use in this function)
drivers/net/ipa/ipa_endpoint.c: In function 'ipa_endpoint_stop':
drivers/net/ipa/ipa_endpoint.c:1309:16: error: 'IPA_ENDPOINT_STOP_RX_RETRIES' undeclared (first use in this function)
These functions were removed in a series, merged in as
commit 33395f4a5c ("Merge branch 'net-ipa-kill-endpoint-stop-workaround'").
Remove them again so that the build works properly.
Fixes: 3793faad7b ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous commit made ipa_endpoint_stop() be a trivial wrapper
around gsi_channel_stop(). Since it no longer does anything
special, just open-code it in the three places it's used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only reason ipa_endpoint_stop() had a retry loop was that the
just-removed workaround required an IPA DMA command to occur between
attempts. The gsi_channel_stop() call that implements the stop does
its own retry loop, to cover a channel's transition from started to
stop-in-progress to stopped state.
Get rid of the unnecessary retry loop in ipa_endpoint_stop().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_stop(), a workaround is used for IPA version 3.5.1
where a 1-byte DMA request is issued between GSI channel stop
retries.
It turns out that this workaround is only required for IPA versions
3.1 and 3.2, and we don't support those. So remove the call to
ipa_endpoint_stop_rx_dma() in that function. That leaves that
function unused, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_stop(), for TX endpoints we set the number of retries
to 0. When we break out of the loop, retries being 0 means we return
EIO rather than the value of ret (which should be 0).
Fix this by using a non-zero retry count for both RX and TX
channels, and just break out of the loop after calling
gsi_channel_stop() for TX channels. This way only RX channels
will retry, and the retry count will be non-zero at the end
for TX channels (so the proper value gets returned).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 713b6ebb4c)
Signed-off-by: David S. Miller <davem@davemloft.net>
A "delay mode" feature was put in place to work around a problem
that was observed during development of the upstream IPA driver. It
used TX endpoint "delay mode" in order to prevent transmitting
packets toward the modem before it was ready.
A race condition that would explain the problem has long since been
fixed, and we have concluded that the "delay mode" feature is no
longer required. So get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new helper function that encapsulates enabling or disabling
suspend on an RX endpoint. It returns the previous state of the
endpoint (true means suspend mode was enabled).
Create another function that handles enabling or disabling delay mode
on a TX endpoint. Delay mode does not work correctly on IPA version
4.2, so we don't currently use it (and shouldn't).
We only set delay mode in one case, and although we don't expect an
endpoint to already be in delay mode, it doesn't really matter if it
was. So the delay function doesn't return a value.
Stop issuing warnings if the previous suspend or delay mode state
differs from what is expected.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ipa_endpoint_init_ctrl() so it returns the previous state
(whether suspend or delay mode was enabled) rather than indicating
whether the request caused a change in state. This makes it easier
to understand what's happening where called.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places, a Boolean flag is used in the GSI code to
indicate whether the "doorbell engine" should be enabled or not
when a channel is configured. This is basically done to abstract
this property from the IPA version; the GSI code doesn't otherwise
"know" what the IPA hardware version is. The doorbell engine is
enabled only for IPA v3.5.1, not for IPA v4.0 and later.
The next patch makes another change that affects behavior during
channel reset (which also involves programming the channel). It
also distinguishes IPA v3.5.1 hardware from newer hardware.
Rather than creating another flag whose value matches the "db_enable"
value, just rename "db_enable" to be "legacy" so it can be used to
signal more than just the special doorbell handling.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipa_endpoint_stop(), for TX endpoints we set the number of retries
to 0. When we break out of the loop, retries being 0 means we return
EIO rather than the value of ret (which should be 0).
Fix this by using a non-zero retry count for both RX and TX
channels, and just break out of the loop after calling
gsi_channel_stop() for TX channels. This way only RX channels
will retry, and the retry count will be non-zero at the end
for TX channels (so the proper value gets returned).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't assume the receive buffer size is a power-of-2 number of pages.
Instead, define the receive buffer size independently, and then
compute the page order from that size when needed.
This fixes a build problem that arises when the ARM64_PAGE_SHIFT
config option is set to have a page size greater than 4KB. The
problem was identified by Linux Kernel Functional Testing.
The IPA code basically assumed the page size to be 4KB. A larger page
size caused the receive buffer size to become correspondingly larger
(32KB or 128KB for ARM64_16K_PAGES and ARM64_64K_PAGES, respectively).
The receive buffer size is used to compute an "aggregation byte limit"
value that gets programmed into the hardware, and the large page sizes
caused that limit value to be too big to fit in a 5 bit field. This
triggered a BUILD_BUG_ON() call in ipa_endpoint_validate_build().
This fix causes a lot of receive buffer memory to be wasted if
system is configured for page size greater than 4KB. But such a
misguided configuration will now build successfully.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the code implementing an IPA endpoint. This is
the primary abstraction implemented by the IPA. An endpoint is one
end of a network connection between two entities physically
connected to the IPA. Specifically, the AP and the modem implement
endpoints, and an (AP endpoint, modem endpoint) pair implements the
transfer of network data in one direction between the AP and modem.
Endpoints are built on top of GSI channels, but IPA endpoints
represent the higher-level functionality that the IPA provides.
Data can be sent through a GSI channel, but it is the IPA endpoint
that represents what is on the "other end" to receive that data.
Other functionality, including aggregation, checksum offload and
(at some future date) IP routing and filtering are all associated
with the IPA endpoint.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder