In lag mode, setting roce enabled/disable of lag device have no effect.
e.g.: bond device (roce/vf_lag) roce status remain unchanged.
Therefore disable it and add an error message.
Fixes: cc9defcbb8 ("net/mlx5: Handle "enable_roce" devlink param")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In dual port mode, setting roce enabled/disable for the slave device
have no effect. e.g.: the slave device roce status remain unchanged.
Therefore disable it and add an error message.
Enable or disable roce of the master device affect both master and slave
devices.
Fixes: cc9defcbb8 ("net/mlx5: Handle "enable_roce" devlink param")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Devlink reload can't be allowed on a multi port slave device, because
reload of slave device doesn't take effect.
The right flow is to disable devlink reload for multi port slave
device. Hence, disabling it in mlx5_core probing.
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
wait_for_resync is unreliable - if it timeouts, priv_rx will be freed
anyway. However, mlx5e_ktls_handle_get_psv_completion will be called
sooner or later, leading to use-after-free. For example, it can happen
if a CQ error happened, and ICOSQ stopped, but later on the queues are
destroyed, and ICOSQ is flushed with mlx5e_free_icosq_descs.
This patch converts the lifecycle of priv_rx to fully refcount-based, so
that the struct won't be freed before the refcount goes to zero.
Fixes: 0419d8c9d8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The commit mentioned below has split the parameters of ICOSQ and async
ICOSQ, but it contained a typo: the CQ parameters were swapped for ICOSQ
and async ICOSQ. Async ICOSQ is longer than the normal ICOSQ, and the CQ
size must be the same as the size of the corresponding SQ, but due to
this bug, the CQ of async ICOSQ was much shorter than async ICOSQ
itself. It led to overflows of the CQ with such messages in dmesg, in
particular, when running multiple kTLS-offloaded streams:
mlx5_core 0000:08:00.0: cq_err_event_notifier:529:(pid 9422): CQ error
on CQN 0x406, syndrome 0x1
mlx5_core 0000:08:00.0 eth2: mlx5e_cq_error_event: cqn=0x000406
event=0x04
This commit fixes the issue by using the corresponding parameters for
ICOSQ and async ICOSQ.
Fixes: c293ac927f ("net/mlx5e: Refactor build channel params")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The commit cited below switched from using napi_synchronize to
synchronize_rcu to have a guarantee that it will finish in finite time.
However, on average, synchronize_rcu takes more time than
napi_synchronize. Given that it's called multiple times per channel on
deactivation, it accumulates to a significant amount, which causes
timeouts in some applications (for example, when using bonding with
NetworkManager).
This commit replaces synchronize_rcu with synchronize_net, which is
faster when called under rtnl_lock, allowing to speed up the described
flow.
Fixes: 9c25a22dfb ("net/mlx5e: Use synchronize_rcu to sync with NAPI")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, when we discover a fatal error, we are queueing a work that
will wait for a lock in order to enter the device to error state.
Meanwhile, FW commands are still being processed, and gets timeouts.
This can block the driver for few minutes before the work will manage
to get the lock and enter to error state.
Setting the device to error state before queueing health work, in order
to avoid FW commands being processed while the work is waiting for the
lock.
Fixes: c1d4d2e92a ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
struct mlx5e_params contains fields ({rx,tx}_cq_moderation) that depend
on two things: whether DIM is enabled and the state of a private flag
(MLX5E_PFLAG_{RX,TX}_CQE_BASED_MODER). Whenever the DIM state changes,
mlx5e_reset_{rx,tx}_moderation is called to update the fields, however,
only if the channels are open. The flow where the channels are closed
misses the required update of the fields. This commit moves the calls of
mlx5e_reset_{rx,tx}_moderation, so that they run in both flows.
Fixes: ebeaf084ad ("net/mlx5e: Properly set default values when disabling adaptive moderation")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When mlx5e_ethtool_set_coalesce doesn't change DIM state
(enabled/disabled), it calls mlx5e_set_priv_channels_coalesce
unconditionally, which in turn invokes a firmware command to set
interrupt moderation parameters. It shouldn't happen while DIM manages
those parameters dynamically (it might even be happening at the same
time).
This patch fixes it by splitting mlx5e_set_priv_channels_coalesce into
two functions (for RX and TX) and calling them only when DIM is disabled
(for RX and TX respectively).
Fixes: cb3c7fd4f8 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This limitation was inherited by previous Innova (FPGA) IPsec
implementation, it uses its private set of RQ handlers which
does not support XDP, for Connect-X this is no longer true.
Fix by keeping this limitation only for Innova IPsec supporting devices,
as otherwise this limitation effectively wrongly blocks XDP for all
future Connect-X devices for all flows even if IPsec offload is not
used.
Fixes: 2d64663cd5 ("net/mlx5: IPsec: Add HW crypto offload support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This limitation was inherited by previous Innova (FPGA) IPsec
implementation, it uses its private set of RQ handlers which does
not support striding rq, for Connect-X this is no longer true.
Fix by keeping this limitation only for Innova IPsec supporting devices,
as otherwise this limitation effectively wrongly blocks striding RQs for
all future Connect-X devices for all flows even if IPsec offload is not
used.
Fixes: 2d64663cd5 ("net/mlx5: IPsec: Add HW crypto offload support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
rate_bytes_ps is a 64-bit field. It passed as 32-bit field to
apply_police_params(). Due to this when police rate is higher
than 4Gbps, 32-bit calculation ignores the carry. This results
in incorrect rate configurationn the device.
Fix it by performing 64-bit calculation.
Fixes: fcb64c0f56 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Cleaning up tx descriptors first increases the chance that
rtl_rx() can allocate new skb's from the cache.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If xdp_do_redirect() fails, the calling driver should handle recycling
or freeing of the page associated with the frame. The dpaa2-eth driver
didn't do either of them and just incremented a counter.
Fix this by trying to DMA map back the page and recycle it or, if the
mapping fails, just free it.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FSL_ENETC_MDIO use symbols from PHYLIB (MDIO_BUS) and MDIO_DEVRES,
however there are no dependency specified in Kconfig
ERROR: modpost: "__mdiobus_register" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "mdiobus_unregister" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "devm_mdiobus_alloc_size" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
add depends on MDIO_DEVRES && MDIO_BUS
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition should be skipped if CPU ID equal to nthreads.
The patch doesn't fix any actual issue since
nthreads = min_t(unsigned int, num_present_cpus(), MVPP2_MAX_THREADS).
On all current Armada platforms, the number of CPU's is
less than MVPP2_MAX_THREADS.
Fixes: e531f76757 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
J721e, J7200 and AM64 have multi port switches which can work in multi
mac mode and in switch mode. Add support for configuring this HW in
switch mode using devlink and switchdev notifiers.
Support is similar to existing CPSW switchdev implementation of TI's 32 bit
platform like AM33/AM43/AM57.
To enable switch mode:
devlink dev param set platform/8000000.ethernet name switch_mode value true cmode runtime
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence AM65 CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register netdevice notifiers in order to receive notification when
individual MAC ports are added to the HW bridge.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM65 NUSS ethernet switch on K3 devices can be configured to work either
in independent mac mode where each port acts as independent network
interface (multi mac) or switch mode.
Add devlink hooks to provide a way to switch b/w these modes.
Rationale to use devlink instead of defaulting to bridge mode is that
SoC use cases require to support multiple independent MAC ports with no
switching so that users can use software bridges with multi-mac
configuration (e.g: to support LAG, HSR/PRP, etc). Also, switching
between multi mac and switch mode requires significant Port and ALE
reconfiguration, therefore is easier to be made as part of mode change
devlink hooks. It also allows to keep user interface similar to what
was implemented for the previous generation of TI CPSW IP
(on AM33/AM43/AM57 SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use le32_to_cpu() for reading __le32 struct field filled by hw.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ETH_FCS_LEN instead of magic value and drop incorrect + 2
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Fix "ensable" typo noticed by Andrew
2. Fix chipset name in the struct net_device_ops variable
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems preferred to let compiler optimize code if applicable.
While at it drop unused enet_umac_maskset().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_alloc_coherent takes care of zeroing allocated memory
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compatible string was updated to match normal naming convention so
update driver as well
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K silicon support loopback for selftest or debug purposes.
This patch does necessary configuration to loopback packets upon receiving
request from LMAC mapped RVU PF's netdev via mailbox.
Also MAC (CGX) on OcteonTx2 silicon variants and MAC (RPM) on
OcteonTx3 CN10K are different and loopback needs to be configured
differently. Upper layer interface between RVU AF and PF netdev is
kept same. Based on silicon variant appropriate fn() pointer is
called to config the MAC.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPM supports below list of counters as an extension to existing counters
* class based flow control pause frames
* vlan/jabber/fragmented packets
* fcs/alignment/oversized error packets
This patch adds support to display supported RPM counters via debugfs
and define new mbox rpm_stats to read all support counters.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control configuration is different for CGX(Octeontx2)
and RPM(CN10K) functional blocks. This patch adds the necessary
changes for RPM to support 802.3 pause frames configuration on
cn10k platforms.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K supports max MTU of 16K on LMAC links and 64k on LBK
links and Octeontx2 silicon supports 9K mtu on both links.
Get the same from nix_get_hw_info mbox message in netdev probe.
This patch also calculates receive buffer size required based
on the MTU set.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OcteonTx3 CN10K silicon supports bigger MTU when compared
to 9216 MTU supported by OcteonTx2 silicon variants. Lookback
interface supports upto 64K and RPM LMAC interfaces support
upto 16K.
This patch does the necessary configuration and adds support
for PF/VF drivers to retrieve max packet size supported via mbox
This patch also configures tx link credit by considering supported
fifo size and max packet length for Octeontx3 silicon.
This patch also removes platform specific name from the driver name.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX uses unique channel numbers to identify the packet sources/sinks
like CGX,LBK and SDP. The channel numbers assigned to each block are
hardwired in CN9xxx silicon.
The fixed channel numbers in CN9xxx are:
0x0 | a << 8 | b - LBK(0..3)_CH(0..63)
0x0 | a << 8 - Reserved
0x700 | a - SDP_CH(0..255)
0x800 | a << 8 | b << 4 | c - CGX(0..7)_LMAC(0..3)_CH(0..15)
All the channels in the above fixed enumerator(with maximum
number of blocks) are not required since some chips
have less number of blocks.
For CN10K silicon the channel numbers need to be programmed by
software in each block with the base channel number and range of
channels. This patch calculates and assigns the channel numbers
to efficiently distribute the channel number range(0-4095) among
all the blocks. The assignment is made based on the actual number of
blocks present and also contiguously leaving no holes.
The channel numbers remaining after the math are used as new CPT
replay channels present in CN10K. Also since channel numbers are
not fixed the transmit channel link number needed by AF consumers
is calculated by AF and sent along with nix_lf_alloc mailbox response.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OcteonTx2's next gen platform the CN10K has RPM MAC which has a
different serdes when compared to CGX MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with CGX MAC, with few exceptions though. So we are using the same
CGX driver for RPM MAC as well and will have a different set of APIs
for RPM where ever necessary.
This patch adds initial support for CN10K's RPM MAC i.e. the driver
registration, communication with firmware etc. For communication with
firmware, RPM provides a different IRQ when compared to CGX.
The CGX and RPM blocks support different features. Currently few
features like ptp, flowcontrol and higig are not supported by RPM. This
patch adds new mailbox message "CGX_FEATURES_GET" to get the list of
features supported by underlying MAC.
RPM has different implementations for RX/TX stats. Unlike CGX,
bar offset of stat registers are different. This patch adds
support to access the same and dump the values in debugfs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to use new LMTST lines for NPA batch free
and burst SQE flush. Adds new dev_hw_ops structure to hold platform
specific functions and create new files cn10k.c and cn10k.h.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On CN10K platform transmit/receive buffer alloc and free from/to hardware
had changed to support burst operation. Whereas pervious silicon's only
support single buffer free at a time.
To Support the same firmware allocates a DRAM region for each PF/VF for
storing LMTLINES. These LMTLINES are used for NPA batch free and for
flushing SQE to the hardware.
PF/VF LMTST region is accessed via BAR4. PFs LMTST region is followed
by its VFs mbox memory. The size of region varies from 2KB to 256KB based
on number of LMTLINES configured.
This patch adds support for
- Mapping PF/VF LMTST region.
- Reserves 0-71 (RX + TX + XDP) LMTST lines for NPA batch
free operation.
- Reserves 72-512 LMTST lines for NIX SQE flush.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On CN10K platform NIX RQ and SQ context structure got changed.
This patch uses new mbox message "NIX_CN10K_AQ_ENQ" for NIX
context initialization on CN10K platform.
This patch also updates the nix_rx_parse_s and nix_sqe_sg_s
structures to add packet steering bit feilds.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On CN10K platform NPA and NIX context structure bit fields
had changed to support new features like bandwidth steering etc.
This patch dumps approprate context for CN10K platform.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIX hardware context structure got changed to accommodate new
features like bandwidth steering, L3/L4 outer/inner checksum
enable/disable etc., on CN10K platform.
This patch defines new mbox message NIX_CN10K_AQ_INST for new
NIX context initialization.
This patch also updates the NPA context structures to accommodate
bit field changes made for CN10K platform.
This patch also removes Big endian bit fields from existing
structures as its support got deprecated in current and upcoming silicons.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitate communication between AF-PF and PF-VF.
On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.
On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.
This patch changes mbox initialization to support both CN9XX and CN10K
platform.
The patch also adds new hw_cap flag to setting hw features like TSO etc
and removes platform specific name from the PF/VF driver name to make it
appropriate for all supported platforms
This patch also removes platform specific name from the PF/VF driver name
to make it appropriate for all supported platforms
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitates communication between AF-PF and PF-VF.
On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.
On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.
This patch changes mbox initialization to support both CN9XX and CN10K
platform.
This patch also adds CN10K PTP subsystem and device IDs to ptp
driver id table.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch check that TX FC firmware is running in CM3.
If not, global TX FC would be disabled.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix GMAC TX flow control autoneg.
Flow control autoneg wrongly were disabled with enabled TX
flow control.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add ethtool flow control configuration support.
Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.
Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.
Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".
This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds CM3 memory map.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The running fw.psid version is in decimal format but the stored
fw.psid is in hex format. This can mislead the user to reset the
NIC to activate the stored version to become the running version.
Fix it to display the stored fw.psid in decimal format.
Fixes: 1388875b39 ("bnxt_en: Add stored FW version info to devlink info_get cb.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up. Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If set_link_state() fails for any reason, we still cleanup the adapter
state and cannot recover from a partial close anyway. So set the adapter
to CLOSED state. That way if a new soft/hard reset is processed, the
adapter will remain in the CLOSED state until the next ibmvnic_open().
Fixes: 01d9bd792d ("ibmvnic: Reorganize device close")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several years ago these two entries have been added, but it's not clear
why. There's no trace that there has ever been such a chip version, and
not even the r8101 vendor driver knows these id's. So let's disable
detection, and if nobody complains remove them completely later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we do the initialization of coalescing values on load.
per queue coalesce values are also restored across up/down of
ethernet interface.
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
per queue coalescing allows better and more finegrained control
over interrupt rates.
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
handle netpoll case when qede_poll is called by
netpoll layer with budget 0
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a random stack value is being returned because variable
_ret_ is not properly initialized. This variable is actually not
used anymore and it should be removed.
Fix this by removing all instances of variable ret and return 0.
Fixes: 64749c9c38 ("net: hns3: remove redundant return value of hns3_uninit_all_ring()")
Addresses-Coverity-ID: 1501700 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
plat_dat is initialized by stmmac_probe_config_dt().
So, initialization is not required by priv->plat.
This removes unnecessary initialization and variables.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we don't re-configure WOL-related register bits when waking up
from hibernation. I'm not aware of any problem reports, but better
play safe and call __rtl8169_set_wol() in the resume() path too.
To achieve this move calling __rtl8169_set_wol() to
rtl8169_net_resume() and rename the function to rtl8169_runtime_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stats_lock is no longer used. So remove it.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several spinlock_t definitions without comments.
Add them.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following checkpatch checks:
CHECK: Macro argument 'off' may be better as '(off)' to
avoid precedence issues
CHECK: Alignment should match open parenthesis
CHECK: multiple assignments should be avoided
CHECK: Blank lines aren't necessary before a close brace '}'
CHECK: Please use a blank line after function/struct/union/enum
declarations
CHECK: Unnecessary parentheses around 'rc != H_FUNCTION'
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following checkpatch warning:
WARNING: Avoid multiple line dereference
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following checkpatch warning:
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following checkpatch warning:
WARNING: networking block comments don't use an empty /* line, use /* Comment...
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following checkpatch warnings:
WARNING: Prefer 'unsigned long' over 'unsigned long int' as the int is unnecessary
WARNING: Prefer 'long' over 'long int' as the int is unnecessary
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-02-10
This series contains updates to i40e driver only.
Arkadiusz adds support for software controlled DCB. Upon disabling of the
firmware LLDP agent, the driver configures DCB with default values
(only one Traffic Class). At the same time, it allows a software based
LLDP agent - userspace application i.e. lldpad) to receive DCB TLVs
and set desired DCB configuration through DCB related netlink callbacks.
Aleksandr implements get and set ethtool ops for Energy Efficient
Ethernet.
Przemyslaw extends support for ntuple filters allowing for Flow Director
IPv6 and VLAN filters.
Kaixu Xia removes an unneeded assignment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return negative error code -ENOMEM from the ioremap() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix to return negative error code from the mlx5e_tc_tun_init() error
handling case instead of 0, as done elsewhere in this function.
This commit also using 0 instead of 'ret' when success since it is
always equal to 0.
Fixes: 8914add2c9 ("net/mlx5e: Handle FIB events to update tunnel endpoint device")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The mlx5_chains_get_table() function doesn't return NULL, it returns
error pointers so we need to fix this condition.
Fixes: 34ca65352d ("net/mlx5: E-Switch, Indirect table infrastructure")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Exclude contents of tc_tun.h header when CONFIG_MLX5_ESWITCH is disabled to
prevent compile-time errors when compiling with such config.
Fixes: 0d9f964714 ("net/mlx5e: Extract tc tunnel encap/decap code to dedicated file")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There is a spelling mistake in a netdev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There is a spelling mistake in a netdev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove including <generated/utsrelease.h> that don't need it.
Fixes: 17a7612b99 ("net/mlx5_core: Clean driver version and name")
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There are some spelling mistakes in the Kconfig. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This entry used when skipping the parser needed,
for example, the custom header pretended to ethernet header.
Suggested-by: Liron Himi <liron@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register set_link_ksetting callback with driver such that
link configurations parameters like advertised mode,speed, duplex
and autoneg can be configured.
below command
ethtool -s eth0 advertise 0x1 speed 10 duplex full autoneg on
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register get_link_ksettings callback to get link status information
from the driver. As virtual function (vf) shares same physical link
same API is used for both the drivers and for loop back drivers
simply returns the fixed values as its does not have physical link.
ethtool eth3
Settings for eth3:
Supported ports: [ ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
10000baseKR/Full
1000baseX/Full
Supports auto-negotiation: No
Supported FEC modes: BaseR RS
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: None
ethtool lbk0
Settings for lbk0:
Speed: 100000Mb/s
Duplex: Full
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CGX supports setting advertised link modes on physical link.
This patch adds support to derive cgx mode from ethtool
link mode and pass it to firmware to configure the same.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CGX LMAC, the physical interface support link configuration parameters
like speed, auto negotiation, duplex etc. Firmware saves these into
memory region shared between firmware and this driver.
This patch adds mailbox handler set_link_mode, fw_data_get to
configure and read these parameters.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to configure fec modes baser/rs and
support to fecth FEC stats from CGX as well PHY.
Configure fec mode
- ethtool --set-fec eth0 encoding rs/baser/off/auto
Query fec mode
- ethtool --show-fec eth0
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to fetch fec stats from PHY. The stats are
put in the shared data struct fwdata. A PHY driver indicates
that it has FEC stats by setting the flag fwdata.phy.misc.has_fec_stats
Besides CGX_CMD_GET_PHY_FEC_STATS, also add CGX_CMD_PRBS and
CGX_CMD_DISPLAY_EYE to enum cgx_cmd_id so that Linux's enum list is in sync
with firmware's enum list.
Signed-off-by: Felix Manlunas <fmanlunas@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CGX block supports forward error correction modes baseR
and RS. This patch adds support to set encoding mode
and to read corrected/uncorrected block counters
Adds new mailbox handlers set_fec to configure encoding modes
and fec_stats to read counters and also increase mbox timeout
to accomdate firmware command response timeout.
Along with new CGX_CMD_SET_FEC command add other commands to
sync with kernel enum list with firmware.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel pointed that the return of dma_addr_t in
otx2_alloc_rbuf/__otx2_alloc_rbuf() seem suspicious because a negative
error code may be returned in some cases. For a dma_addr_t, the error
code such as -ENOMEM does seem a valid value, so we can't judge if the
buffer allocation fail or not based on that value. Add a parameter for
otx2_alloc_rbuf/__otx2_alloc_rbuf() to store the dma address and make
the return value to indicate if the buffer allocation really fail or
not.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect serial config version information directly from an internal
register, instead of explicitly resizing VPD.
v2:
- Add comments on info stored in PCIE_STATIC_SPARE2 register.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable ret is overwritten by the following call
i40e_clean_arq_element() and the assignment is useless, so remove it.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow user to specify VLAN field and add it to flow director. Show VLAN
field in "ethtool -n ethx" command.
Handle VLAN type and tag field provided by ethtool command. Refactored
filter addition, by replacing static arrays with runtime dummy packet
creation, which allows specifying VLAN field.
Previously, VLAN field was omitted.
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Flow director for IPv6 is not supported.
1) Implementation of support for IPv6 flow director.
2) Added handlers for addition of TCP6, UDP6, SCTP6, IPv6.
3) Refactored legacy code to make it more generic.
4) Added packet templates for TCP6, UDP6, SCTP6, IPv6.
5) Added handling of IPv6 source and destination address for flow director.
6) Improved argument passing for source and destination portin TCP6, UDP6
and SCTP6.
7) Added handling of ethtool -n for IPv6, TCP6,UDP6, SCTP6.
8) Used correct bit flag regarding FLEXOFF field of flow director data
descriptor.
Without this patch, there would be no support for flow director on IPv6,
TCP6, UDP6, SCTP6.
Tested based on x710 datasheet by using:
ethtool -N enp133s0f0 flow-type tcp4 src-port 13 dst-port 37 user-def 0x44142 action 1
ethtool -N enp133s0f0 flow-type tcp6 src-port 13 dst-port 40 user-def 0x44142 action 2
ethtool -N enp133s0f0 flow-type udp4 src-port 20 dst-port 40 user-def 0x44142 action 3
ethtool -N enp133s0f0 flow-type udp6 src-port 25 dst-port 40 user-def 0x44142 action 4
ethtool -N enp133s0f0 flow-type sctp4 src-port 55 dst-port 65 user-def 0x44142 action 5
ethtool -N enp133s0f0 flow-type sctp6 src-port 60 dst-port 40 user-def 0x44142 action 6
ethtool -N enp133s0f0 flow-type ip4 src-ip 1.1.1.1 dst-ip 1.1.1.4 user-def 0x44142 action 7
ethtool -N enp133s0f0 flow-type ip6 src-ip fe80::3efd:feff:fe6f:bbbb dst-ip fe80::3efd:feff:fe6f:aaaa user-def 0x44142 action 8
Then send traffic from client which matches the criteria provided to ethtool.
Observe that packets are redirected to user set queues with ethtool -S <interface>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement Energy Efficient Ethernet (EEE) status getting & setting.
The i40e_get_eee() requesting PHY EEE capabilities from firmware.
The i40e_set_eee() function requests PHY EEE capabilities
from firmware and sets PHY EEE advertising to full abilities or 0
depending whether EEE is to be enabled or disabled.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks used by software based LLDP agent, which allows to
configure DCB feature from userspace.
Update copyright dates as appropriate.
If LLDP agent is turned off in BIOS, or after setting private flag
("disable-fw-lldp on"). The driver initialized DCB functionality with
default values, one traffic class with 100% bandwidth allocated.
The new netlink callbacks are required for software LLDP agent, it
must be able to acquire current DCB configuration of a network port
and apply DCB configuration changes, if required.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add extra handling on changing the "disable-fw-lldp" private
flag to properly initialize software based DCB feature.
Add default configuration of DCB functionality when Firmware
LLDP agent is turned off, in case of driver probe and device
reset on reconfiguration.
Update copyright dates as appropriate.
Software based DCB is a brand-new feature in i40e driver.
Before, DCB was implemented by Firmware LLDP agent only. The agent was
responsible for handling incoming DCB-related LLDP frames and
applying received DCB configuration to hardware.
Default configuration and new initialization flow for software based
DCB is required. If LLDP agent is turned off in BIOS, or after
setting private flag ("disable-fw-lldp on"). The driver initializes
DCB functionality with default values, one traffic class with 100%
bandwidth allocated.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add registers and definitions required for applying
DCB related hardware configuration.
Add functions responsible for calculating and setting proper
hardware configuration values for software based DCB functionality.
Add function responsible for invoking Admin Queue command, which
results in applying new DCB configuration to the hardware.
Update copyright dates as appropriate.
Software based DCB is a brand-new feature in i40e driver.
Before, DCB was implemented by Firmware LLDP agent only. The agent was
responsible for handling incoming DCB-related LLDP frames and
applying received DCB configuration to hardware.
New communication channel between software and hardware is required
for software driver. It must be able to calculate and configure all
the registers related for DCB feature.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-02-08
This series contains updates to i40e driver only.
Cristian makes improvements to driver XDP path. Avoids writing
next-to-clean pointer on every update, removes redundant updates of
cleaned_count and buffer info, creates a helper function to consolidate
XDP actions and simplifies some of the behavior.
Eryk adds messages to inform the user when MTU is larger than supported
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-02-08
This series contains updates to the ice driver and documentation.
Brett adds a log message when a trusted VF goes in and out of promiscuous
for consistency with i40e driver.
Dave implements a new LLDP command that allows adding VSI destinations to
existing filters and adds support for netdev bonding events, current
support is software based.
Michal refactors code to move from VSI stored xsk_buff_pools to
netdev-provided ones.
Kiran implements the creation scheduler aggregator nodes and distributing
VSIs within the nodes.
Ben modifies rate limit calculations to use clock frequency from the
hardware instead of using a hardcoded one.
Jesse adds support for user to control writeback frequency.
Chinh refactors DCB variables out of the ice_port_info struct.
Bruce removes some unnecessary casting.
Mitch fixes an error message that was reported as if_up instead of if_down.
Tony adjusts fallback allocation for MSI-X to use all given vectors instead
of using only the minimum configuration and updates documentation for
the ice driver.
====================
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the RSS commands of VF are using host byte order.
According to the user manual, it should use little endian in
the command to firmware. For the host and firmware are both
using little endian, so it can work well in this case.
Do cleanup to make it more explicitly.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some macros are defined but unused, so remove them.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameter vf in hclge_vf_rate_param_check() is unused now,
so remove it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hns3_uninit_all_ring() only returns 0, so remove this
redundant return value and function declaration in hns3_enet.h.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of parameter mpf_bd_num and pf_bd_num in
hclge_query_bd_num() should be u32* instead of int*,
so change them.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of parameters in hclge_parse_speed() should be
unsigned type, so change them.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an issue where the formatting symbol of the formatting input and
output function does not match the actual type.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In macro definitions, parentheses are unnecessary in some cases,
such as the calling parameter of a function, the left variable
of the equal sign, and so on. So remove these unnecessary
parentheses according to these rules.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the code more readable, this patch adds a definition for
the magic number 126 used for the default shaper param ir_b, and
rename macro DIVISOR_IR_B_126.
No functional change.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the real tx queue number and real rx queue number
always be updated when netdev opens, it's redundant
to call hclge_client_setup_tc to do the same thing.
So remove it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue_id, qset_id and other IDs are unsigned type, so modify
the corresponding local variables' type in hclge_dbg_dump_tm_map()
from signed to unsigned. kstrtouint() and the print format should
be updated as well.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this index before using it in hclge_get_rss_key().
Fixes: a638b1d8cc ("net: hns3: fix get VF RSS issue")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tqp_index is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this tqp_index before using it in hclge_get_ring_chain_from_mbx().
Fixes: 84e095d64e ("net: hns3: Change PF to add ring-vect binding & resetQ to mailbox")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The queue_id is received from vf, if use it directly,
an out-of-bound issue may be caused, so add a check for
this queue_id before using it in hclge_reset_vf_queue().
Fixes: 1a426f8b40 ("net: hns3: fix the VF queue reset flow error")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM4908 SoCs family uses Ethernel controller that includes UniMAC but
uses different DMA engine (than other controllers) and requires
different programming.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to link XDP prog with MTU larger than supported,
user is not informed why XDP linking fails. Adding proper
error message: "MTU too large to enable XDP".
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Consolidate the actions performed on the packet based on the XDP
program result into a separate function that is easier to read and
maintain. Simplify the i40e_construct_skb_zc function, so that the
input xdp buffer is always freed, regardless of whether the output
skb is successfully created or not. Simplify the behavior of the
i40e_clean_rx_irq_zc function, so that the current packet descriptor
is dropped when function i40_construct_skb_zc returns an error as
opposed to re-processing the same description on the next invocation.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For performance reasons, remove the redundant buffer info updates
(*bi = NULL). The buffers ready to be cleaned can easily be tracked
based on the ring next-to-clean variable, which is consistently
updated.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For performance reasons, remove the redundant updates of the cleaned_count
variable, as its value can be computed based on the ring next-to-clean
variable, which is consistently updated.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For performance reasons, avoid writing the ring next-to-clean pointer
value back to memory on every update, as it is not really necessary.
Instead, simply read it at initialization into a local copy, update
the local copy as necessary and write the local copy back to memory
after the last update.
Signed-off-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When FIB_EVENT_ENTRY_{REPLACE, APPEND} are triggered and route insertion
fails, FIB abort is triggered.
After aborting, set the appropriate hardware flag to make the kernel emit
RTM_NEWROUTE notification with RTM_F_OFFLOAD_FAILED flag.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv6 routes, so that
users will have better visibility into the offload process.
'struct fib6_info' is extended with new field that indicates if route
offload failed. Note that the new field is added using unused bit and
therefore there is no need to increase struct size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv4 routes, so that
users will have better visibility into the offload process.
'struct fib_alias', and 'struct fib_rt_info' are extended with new field
that indicates if route offload failed. Note that the new field is added
using unused bit and therefore there is no need to increase structs size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the synchronize_srcu() from the ODP flow as it was found to be a
very heavy time consumer as part of dereg_mr.
For example de-registration of 10000 ODP MRs each with size of 2M hugepage
took 19.6 sec comparing de-registration of same number of non ODP MRs that
took 172 ms.
The new locking scheme uses the wait_event() mechanism which follows the
use count of the MR instead of using synchronize_srcu().
By that change, the time required for the above test took 95 ms which is
even better than the non ODP flow.
Once fully dropped the srcu usage, had to come with a lock to protect the
XA access.
As part of using the above mechanism we could also clean the
num_deferred_work stuff and follow the use count instead.
Link: https://lore.kernel.org/r/20210202071309.2057998-1-leon@kernel.org
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Currently if the driver is unable to get all the MSI-X vectors it wants, it
falls back to the minimum configuration which equates to a single Tx/Rx
traffic queue pair. Instead of using the minimum configuration, if given
more vectors than the minimum, utilize those vectors for additional traffic
queues after accounting for other interrupts.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
This message indicates an error on close, not open.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Casting a void * rvalue in an assignment is unnecessary in C; remove the
casts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the DCB related variables out of the ice_port_info_struct. The
goal is to make the ice_port_info struct cleaner.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Co-developed-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The writeback enable logic was incorrectly implemented (due to
misunderstanding what the side effects of the implementation would be
during polling).
Fix this logic issue, while implementing a new feature allowing the user
to control the writeback frequency using the knobs for controlling
interrupt throttling that we already have. Basically if you leave
adaptive interrupts enabled, the writeback frequency will be varied even
if busy_polling or if napi-poll is in use. If the interrupt rates are
set to a fixed value by ethtool -C and adaptive is off, the driver will
allow the user-set interrupt rate to guide how frequently the hardware
will complete descriptors to the driver.
Effectively the user will get a control over the hardware efficiency,
allowing the choice between immediate interrupts or delayed up to a
maximum of the interrupt rate, even when interrupts are disabled
during polling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The core clock frequency is currently hardcoded at 446 MHz for the RL
profile calculations. This causes issues since not all devices use that
clock frequency. Read the GLGEN_CLKSTAT_SRC register to determine which PSM
clock frequency is selected. This ensures that the rate limiter profile
calculations will be correct.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create set scheduler aggregator node and move for VSIs into respective
scheduler node. Max children per aggregator node is 64.
There are two types of aggregator node(s) created.
1. dedicated node for PF and _CTRL VSIs
2. dedicated node(s) for VFs.
As part of reset and rebuild, aggregator nodes are recreated and VSIs
are moved to respective aggregator node.
Having related VSIs in respective tree avoid starvation between PF and VF
w.r.t Tx bandwidth.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Co-developed-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Victor Raj <victor.raj@intel.com>
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the framework and initial implementation for receiving and processing
netdev bonding events. This is only the software support and the
implementation of the HW offload for bonding support will be coming at a
later time. There are some architectural gaps that need to be closed
before that happens.
Because this is a software only solution that supports in kernel bonding,
SR-IOV is not supported with this implementation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current implementation of netdev already contains xsk_buff_pools.
We no longer have to contain these structures in ice_vsi.
Refactor the code to operate on netdev-provided xsk_buff_pools.
Move scheduling napi on each queue to a separate function to
simplify setup function.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is an issue with some NVMs where an already existent LLDP
filter is blocking the creation of a filter to allow LLDP packets
to be redirected to the default VSI for the interface. This is
blocking all LLDP functionality based in the kernel when the FW
LLDP agent is disabled (e.g. software based DCBx).
Implement the new AQ command to allow adding VSI destinations to
existent filters on NVM versions that support the new command.
The new lldp_fltr_ctrl AQ command supports Rx filters only, so the
code flow for adding filters to disable Tx of control frames will
remain intact.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently there is no message printed on the host when a VF goes in and
out of promiscuous mode. This is causing confusion because this is the
expected behavior based on i40e. Fix this.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Vlad Buslov says:
=================
Implement support for VF tunneling
Abstract
Currently, mlx5 only supports configuration with tunnel endpoint IP address on
uplink representor. Remove implicit and explicit assumptions of tunnel always
being terminated on uplink and implement necessary infrastructure for
configuring tunnels on VF representors and updating rules on such tunnels
according to routing changes.
SW TC model
From TC perspective VF tunnel configuration requires two rules in both
directions:
TX rules
1. Rule that redirects packets from UL to VF rep that has the tunnel
endpoint IP address:
$ tc -s filter show dev enp8s0f0 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 16:c9:a0:2d:69:2c
src_mac 0c:42:a1:58:ab:e4
eth_type ipv4
ip_flags nofrag
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 3 ref 1 bind 1 installed 377 sec used 0 sec
Action statistics:
Sent 114096 bytes 952 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 114096 bytes 952 pkt
backlog 0b 0p requeues 0
cookie 878fa48d8c423fc08c3b6ca599b50a97
no_percpu
used_hw_stats delayed
2. Rule that decapsulates the tunneled flow and redirects to destination VF
representor:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
RX rules
1. Rule that encapsulates the tunneled flow and redirects packets from
source VF rep to tunnel device:
$ tc -s filter show dev enp8s0f0_1 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 0a:40:bd:30:89:99
src_mac ca:2e:a7:3f:f5:0f
eth_type ipv4
ip_tos 0/0x3
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key set
src_ip 7.7.7.5
dst_ip 7.7.7.1
key_id 98
dst_port 4789
nocsum
ttl 64 pipe
index 1 ref 1 bind 1 installed 411 sec used 411 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
no_percpu
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device vxlan_sys_4789) stolen
index 1 ref 1 bind 1 installed 411 sec used 0 sec
Action statistics:
Sent 5615833 bytes 4028 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 5615833 bytes 4028 pkt
backlog 0b 0p requeues 0
cookie bb406d45d343bf7ade9690ae80c7cba4
no_percpu
used_hw_stats delayed
2. Rule that redirects from tunnel device to UL rep:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
HW offloads model
For hardware offload the goal is to mach packet on both rules without exposing
it to software on tunnel endpoint VF. In order to achieve this for tx, TC
implementation marks encap rules with tunnel endpoint on mlx5 VF of same eswitch
with MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE flag and adds header modification
rule to overwrite packet source port to the value of tunnel VF. Eswitch code is
modified to recirculate such packets after source port value is changed, which
allows second tx rules to match.
For rx path indirect table infrastructure is used to allow fully processing VF
tunnel traffic in hardware. To implement such pipeline driver needs to program
the hardware after matching on UL rule to overwrite source vport from UL to
tunnel VF and recirculate the packet to the root table to allow matching on the
rule installed on tunnel VF. For this, indirect table matches all encapsulated
traffic by tunnel parameters and all other IP traffic is sent to tunnel VF by
the miss rule. Such configuration will cause packet to appear on VF representor
instead of VF itself if packet has been matches by indirect table rule based on
tunnel parameters but missed on second rule (after recirculation). Handle such
case by marking packets processed by indirect table with special 0xFFF value in
reg_c1 and extending slow table with additional flow group that matches on
reg_c0 (source port value set by indirect tables) and reg_c1 (special 0xFFF
mark). When creating offloads fdb tables, install one rule per VF vport to match
on recirculated miss packets and redirect them to appropriate VF vport.
Routing events
In order to support routing changes and migration of tunnel device between
different endpoint VFs, implement routing infrastructure and update it with FIB
events. Routing entry table is introduced to mlx5 TC. Every rx and tx VF tunnel
rule is attached to a routing entry, which is shared for rules of same tunnel.
On FIB event the work is scheduled to delete/recreate all rules of affected
tunnel.
Note: only vxlan tunnel type is supported by this series.
=================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmAeINMACgkQSD+KveBX
+j5ssAgAlmHUXB13W8FzXmp37hj6990QVVUNMe1tX09u6TOKi3X9VgRydCLdZlIm
CEgdknjhlesjiYsy4z9o8MTV4IXGnNoy+qW9cuL9SCpDpVLeJ0g+3/laUv21oOhr
zGxR4nmLwDxpzAj8huqOv5kVlojiA90x9wZIiOjx0+obOmglhfjzpUORAGXeHQTf
yxeiEi1ef5MO02lE854gzPBF60XB6LN7+Viw+4E+G67n7TdvIQ0xu2j/DpOubpH2
BzXoU12a424FvpAhhW8xrIZF4wFEo120Ln+vDMGq30Hqo/9gFQ1EmSBXaOOVhPwx
M/gJ3OJhckrMpNs36tdCyoOm/pTS+w==
=7d1N
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2021-02-04
Vlad Buslov says:
=================
Implement support for VF tunneling
Abstract
Currently, mlx5 only supports configuration with tunnel endpoint IP address on
uplink representor. Remove implicit and explicit assumptions of tunnel always
being terminated on uplink and implement necessary infrastructure for
configuring tunnels on VF representors and updating rules on such tunnels
according to routing changes.
SW TC model
From TC perspective VF tunnel configuration requires two rules in both
directions:
TX rules
1. Rule that redirects packets from UL to VF rep that has the tunnel
endpoint IP address:
$ tc -s filter show dev enp8s0f0 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 16:c9:a0:2d:69:2c
src_mac 0c:42:a1:58:ab:e4
eth_type ipv4
ip_flags nofrag
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 3 ref 1 bind 1 installed 377 sec used 0 sec
Action statistics:
Sent 114096 bytes 952 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 114096 bytes 952 pkt
backlog 0b 0p requeues 0
cookie 878fa48d8c423fc08c3b6ca599b50a97
no_percpu
used_hw_stats delayed
2. Rule that decapsulates the tunneled flow and redirects to destination VF
representor:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
RX rules
1. Rule that encapsulates the tunneled flow and redirects packets from
source VF rep to tunnel device:
$ tc -s filter show dev enp8s0f0_1 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 0a:40:bd:30:89:99
src_mac ca:2e:a7:3f:f5:0f
eth_type ipv4
ip_tos 0/0x3
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key set
src_ip 7.7.7.5
dst_ip 7.7.7.1
key_id 98
dst_port 4789
nocsum
ttl 64 pipe
index 1 ref 1 bind 1 installed 411 sec used 411 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
no_percpu
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device vxlan_sys_4789) stolen
index 1 ref 1 bind 1 installed 411 sec used 0 sec
Action statistics:
Sent 5615833 bytes 4028 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 5615833 bytes 4028 pkt
backlog 0b 0p requeues 0
cookie bb406d45d343bf7ade9690ae80c7cba4
no_percpu
used_hw_stats delayed
2. Rule that redirects from tunnel device to UL rep:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
HW offloads model
For hardware offload the goal is to mach packet on both rules without exposing
it to software on tunnel endpoint VF. In order to achieve this for tx, TC
implementation marks encap rules with tunnel endpoint on mlx5 VF of same eswitch
with MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE flag and adds header modification
rule to overwrite packet source port to the value of tunnel VF. Eswitch code is
modified to recirculate such packets after source port value is changed, which
allows second tx rules to match.
For rx path indirect table infrastructure is used to allow fully processing VF
tunnel traffic in hardware. To implement such pipeline driver needs to program
the hardware after matching on UL rule to overwrite source vport from UL to
tunnel VF and recirculate the packet to the root table to allow matching on the
rule installed on tunnel VF. For this, indirect table matches all encapsulated
traffic by tunnel parameters and all other IP traffic is sent to tunnel VF by
the miss rule. Such configuration will cause packet to appear on VF representor
instead of VF itself if packet has been matches by indirect table rule based on
tunnel parameters but missed on second rule (after recirculation). Handle such
case by marking packets processed by indirect table with special 0xFFF value in
reg_c1 and extending slow table with additional flow group that matches on
reg_c0 (source port value set by indirect tables) and reg_c1 (special 0xFFF
mark). When creating offloads fdb tables, install one rule per VF vport to match
on recirculated miss packets and redirect them to appropriate VF vport.
Routing events
In order to support routing changes and migration of tunnel device between
different endpoint VFs, implement routing infrastructure and update it with FIB
events. Routing entry table is introduced to mlx5 TC. Every rx and tx VF tunnel
rule is attached to a routing entry, which is shared for rules of same tunnel.
On FIB event the work is scheduled to delete/recreate all rules of affected
tunnel.
Note: only vxlan tunnel type is supported by this series.
=================
It is likely that this is a leftover from T3 driver heritage. cxgb4 uses
the PCI core VPD access code that handles detection of VPD capabilities.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-02-05
This series contains updates to ice driver only.
Jake adds adds reporting of timeout length during devlink flash and
implements support to report devlink info regarding the version of
firmware that is stored (downloaded) to the device, but is not yet active.
ice_devlink_info_get will report "stored" versions when there is no
pending flash update. Version info includes the UNDI Option ROM, the
Netlist module, and the fw.bundle_id.
Gustavo A. R. Silva replaces a one-element array to flexible-array
member.
Bruce utilizes flex_array_size() helper and removes dead code on a check
for a condition that can't occur.
v2:
* removed security revision implementation, and re-ordered patches to
account for this removal
* squashed patches implementing ice_read_flash_module to avoid patches
refactoring the implementation of a previous patch in the series
* modify ice_devlink_info_get to always report "stored" versions instead
of only reporting them when a pending flash update is ready.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: remove dead code
ice: use flex_array_size where possible
ice: Replace one-element array with flexible-array member
ice: display stored UNDI firmware version via devlink info
ice: display stored netlist versions via devlink info
ice: display some stored NVM versions via devlink info
ice: introduce function for reading from flash modules
ice: cache NVM module bank information
ice: introduce context struct for info report
ice: create flash_info structure and separate NVM version
ice: report timeout length for erasing during devlink flash
====================
Link: https://lore.kernel.org/r/20210206044101.636242-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no benefit in trying to disable interrupts if NAPI is
scheduled already. This allows us to save a PCI write in this case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/78c7f2fb-9772-1015-8c1d-632cbdff253f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The verdict returned from ena_xdp_execute() is used to determine the
fate of the RX buffer's page. In case of XDP Redirect/TX error the
verdict should be set to XDP_ABORTED, otherwise the page won't be freed.
Fixes: a318c70ad1 ("net: ena: introduce XDP redirect implementation")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot switch has been supporting LAG offload since its initial
commit, however felix could not make use of that, due to lack of a LAG
abstraction in DSA. Now that we have that, let's forward DSA's calls
towards the ocelot library, who will deal with setting up the bonding.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.
Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.
Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It makes it a bit easier to read and understand the code that deals with
balancing the 16 aggregation codes among the ports in a certain LAG.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.
In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The setup of logical port IDs is done in two places: from the inconclusively
named ocelot_setup_lag and from ocelot_port_lag_leave, a function that
also calls ocelot_setup_lag (which apparently does an incomplete setup
of the LAG).
To improve this situation, we can rename ocelot_setup_lag into
ocelot_setup_logical_port_ids, and drop the "lag" argument. It will now
set up the logical port IDs of all switch ports, which may be just
slightly more inefficient but more maintainable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The index of the LAG is equal to the logical port ID that all the
physical port members have, which is further equal to the index of the
first physical port that is a member of the LAG.
The code gets a bit carried away with logic like this:
if (a == b)
c = a;
else
c = b;
which can be simplified, of course, into:
c = b;
(with a being port, b being lp, c being lag)
This further makes the "lp" variable redundant, since we can use "lag"
everywhere where "lp" (logical port) was used. So instead of a "c = b"
assignment, we can do a complete deletion of b. Only one comment here:
if (bond_mask) {
lp = __ffs(bond_mask);
ocelot->lags[lp] = 0;
}
lp was clobbered before, because it was used as a temporary variable to
hold the new smallest port ID from the bond. Now that we don't have "lp"
any longer, we'll just avoid the temporary variable and zeroize the
bonding mask directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.
We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPv6 header information is not currently part of the entropy source for
the 4-bit aggregation code used for LAG offload, even though it could be.
The hardware reference manual says about these fields:
ANA::AGGR_CFG.AC_IP6_TCPUDP_PORT_ENA
Use IPv6 TCP/UDP port when calculating aggregation code. Configure
identically for all ports. Recommended value is 1.
ANA::AGGR_CFG.AC_IP6_FLOW_LBL_ENA
Use IPv6 flow label when calculating AC. Configure identically for all
ports. Recommended value is 1.
Integration with the xmit_hash_policy of the bonding interface is TBD.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since switchdev/DSA exposes network interfaces that fulfill many of the
same user space expectations that dedicated NICs do, it makes sense to
not deny bonding interfaces with a bonding policy that we cannot offload,
but instead allow the bonding driver to select the egress interface in
software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make ocelot's net device event handler more streamlined by structuring
it in a similar way with others. The inspiration here was
dsa_slave_netdevice_event.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_netdevice_port_event treats a single event, NETDEV_CHANGEUPPER.
So we can remove the check for the type of event, and rename the
function to be more suggestive, since there already is a function with a
very similar name of ocelot_netdevice_event.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The max qset number is a fixed value now and it is defined by a macro.
In order to support other value in different kinds of device, it is
better to use specification queried from firmware to replace macro.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to add a method to check the specification of max tm rate
for debugging, function hns3_dbg_dev_specs() adds this value print.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the newer hardware may supports different frame size,
so add support to obtain the capability from the firmware
instead of the fixed value.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When update the TC info for NIC, there are some differences
between PF and VF. Currently, four "vport->vport_id" are
used to distinguish PF or VF. So merge them into one to
improve readability and maintainability of code.
Signed-off-by: GuoJia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As RSS indirection table size may be different in different
hardware. Instead of using macro, this value is better to use
device specification which querying from firmware.
BTW, RSS indirection table should be allocated by the queried
size instead the static array.
.get_rss_indir_size in struct hnae3_ae_ops is not used now,
so remove it as well.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To improve the compatibility of firmware for driver, help firmware
to deal with different api commands, add api capability bits when
initialize the command queue.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for backplane link mode, which is, according to discussions
with NXP earlier in the year, is a mode where the OS (Linux) is able to
manage the PCS and Serdes itself.
This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that pcs-lynx supports 1000BASE-X, add support for this interface
mode to dpaa2-mac. pcs-lynx can be switched at runtime between SGMII
and 1000BASE-X mode, so allow dpaa2-mac to switch between these as
well.
This commit prepares the ground work for allowing 1G fiber connections
to be used with DPAA2 on the SolidRun CEX7 platforms.
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The napi_alloc_frag_align() will guarantee that a correctly align
buffer address is returned. So use this function to simplify the buffer
alloc and avoid the unnecessary memory waste.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a spelling mistake in the function name alloc_channles_and_rings.
Fix this by renaming it to alloc_channels_and_rings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210204094944.51460-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no guarantee that rmnet rx_handler is only fed with linear
skbs, but current rmnet implementation does not check that, leading
to crash in case of non linear skbs processed as linear ones.
Fix that by ensuring skb linearization before processing.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1612428002-12333-2-git-send-email-loic.poulain@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Align netdevice statistics when the device is running in XDP mode
to other upstream drivers. In particular report to user-space rx
packets even if they are not forwarded to the networking stack
(XDP_PASS) but if they are redirected (XDP_REDIRECT), dropped (XDP_DROP)
or sent back using the same interface (XDP_TX). This patch allows the
system administrator to verify the device is receiving data correctly.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a457cb17dd9c58c116d64ee34c354b2e89c0ff8f.1612375372.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following coccicheck warnings:
./drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:1651:36-38: WARNING
!A || A && B is equivalent to !A || B.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/1612260157-128026-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Normally we clear the failover_pending flag when processing the reset.
But if we are unable to schedule a failover reset we must clear the
flag ourselves. We could fail to schedule the reset if we are in PROBING
state (eg: when booting via kexec) or because we could not allocate memory.
Thanks to Cris Forno for helping isolate the problem and for testing.
Fixes: 1d85049374 ("powerpc/vnic: Extend "failover pending" window")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Tested-by: Cristobal Forno <cforno12@linux.ibm.com>
Link: https://lore.kernel.org/r/20210203050802.680772-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Process FIB route update events to dynamically update the stack device
rules when tunnel routing changes. Use rtnl lock to prevent FIB event
handler from running concurrently with neigh update and neigh stats
workqueue tasks. Use encap_tbl_lock mutex to synchronize with TC rule
update path that doesn't use rtnl lock.
FIB event workflow for encap flows:
- Unoffload all flows attached to route encaps from slow or fast path
depending on encap destination endpoint neigh state.
- Update encap IP header according to new route dev.
- Update flows mod_hdr action that is responsible for overwriting reg_c0
source port bits to source port of new underlying VF of new route dev. This
step requires changing flow create/delete code to save flow parse attribute
mod_hdr_acts structure for whole flow lifetime instead of deallocating it
after flow creation. Refactor mod_hdr code to allow saving id of individual
mod_hdr actions and updating them with dedicated helper.
- Offload all flows to either slow or fast path depending on encap
destination endpoint neigh state.
FIB event workflow for decap flows:
- Unoffload all route flows from hardware. When last route flow is deleted
all indirect table rules for the route dev will also be deleted.
- Update flow attr decap_vport and destination MAC according to underlying
VF of new rote dev.
- Offload all route flows back to hardware creating new indirect table
rules according to updated flow attribute data.
Extract some neigh update code to helper functions to be used by both neigh
update and route update infrastructure.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Some of the encap-specific functions and fields will also be used by route
update infrastructure in following patches. Rename them to generic names.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patch in series implement routing update event which requires
ability to modify rule match_to_reg modify header actions dynamically
during rule lifetime. In order to accommodate such behavior, refactor and
extend TC infrastructure in following ways:
- Modify mod_hdr infrastructure to preserve its parse attribute for whole
rule lifetime, instead of deallocating it after rule creation.
- Extend match_to_reg infrastructure with new function
mlx5e_tc_match_to_reg_set_and_get_id() that returns mod_hdr action id that
can be used afterwards to update the action, and
mlx5e_tc_match_to_reg_mod_hdr_change() that can modify existing actions by
its id.
- Extend tun API with new functions mlx5e_tc_tun_update_header_ipv{4|6}()
that are used to updated existing encap entry tunnel header.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in series implements route update which can cause encap
entries to migrate between routing devices. Consecutively, their parent
nhe's need to be also transferable between devices instead of having neigh
device as a part of their immutable key. Move neigh device from struct
mlx5_neigh to struct mlx5e_neigh_hash_entry and check that nhe and neigh
devices are the same in workqueue neigh update handler.
Save neigh net_device that can change dynamically in dedicated nhe->dev
field. With FIB event handler that is implemented in following patches
changing nhe->dev, NETEVENT_DELAY_PROBE_TIME_UPDATE handler can
concurrently access the nhe entry when traversing neigh list under rcu read
lock. Processing stale values in that handler doesn't change the handler
logic, so just wrap all accesses to the dev pointer in {WRITE|READ}_ONCE()
helpers.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Implement dedicated route entry infrastructure to be used in following
patch by route update event. Both encap (indirectly through their
corresponding encap entries) and decap (directly) flows are attached to
routing entry. Since route update also requires updating encap (route
device MAC address is a source MAC address of tunnel encapsulation), same
encap_tbl_lock mutex is used for synchronization.
The new infrastructure looks similar to existing infrastructures for shared
encap, mod_hdr and hairpin entries:
- Per-eswitch hash table is used for quick entry lookup.
- Flows are attached to per-entry linked list and hold reference to entry
during their lifetime.
- Atomic reference counting and rcu mechanisms are used as synchronization
primitives for concurrent access.
The infrastructure also enables connection tracking on stacked devices
topology by attaching CT chain 0 flow on tunneling dev to decap route
entry.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in series extend the extracted code with routing
infrastructure. To improve code modularity created a dedicated
tc_tun_encap.c source file and move encap/decap related code to the new
file. Export code that is used by both regular TC code and encap/decap code
into tc_priv.h (new header intended to be used only by TC module). Rename
some exported functions by adding "mlx5e_" prefix to their names.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Previous patch in series that implements stack devices RX path implements
indirect table rules that match on tunnel VNI. After such rule is created
all tunnel traffic is recirculated to root table. However, recirculated
packet might not match on any rules installed in the table (for example,
when IP traffic follows ARP traffic). In that case packets appear on
representor of tunnel endpoint VF instead being redirected to the VF
itself.
Extend slow table with additional flow group that matches on reg_c0 (source
port value set by indirect tables implemented by previous patch in series)
and reg_c1 (special 0xFFF mark). When creating offloads fdb tables, install
one rule per VF vport to match on recirculated miss packets and redirect
them to appropriate VF vport. Modify indirect tables code to also rewrite
reg_c1 with special 0xFFF mark.
Implementation reuses reg_c1 tunnel id bits. This is safe to do because
recirculated packets are always matched before decapsulation.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patch in series uses reg_c1 in eswitch code. To use reg_c1
helpers in both TC and eswitch code, refactor existing helpers according to
similar use case of reg_c0 and move the functionality into eswitch.h.
Calculate reg mappings length from new defines to ensure that they are
always in sync and only need to be changed in single place.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove hardcoded match on tunnel destination MAC address. Such match is no
longer required and would be wrong for stacked devices topology where
encapsulation destination MAC address will be the address of tunnel VF that
can change dynamically on route change (implemented in following patches in
the series).
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Indirect table infrastructure is used to allow fully processing VF tunnel
traffic in hardware. Kernel software model uses two TC rules for such
traffic: UL rep to tunnel device, then tunnel VF rep to destination VF rep.
To implement such pipeline driver needs to program the hardware after
matching on UL rule to overwrite source vport from UL to tunnel VF and
recirculate the packet to the root table to allow matching on the rule
installed on tunnel VF. For this indirect table matches all encapsulated
traffic by tunnel parameters and all other IP traffic is sent to tunnel VF
by the miss rule.
Indirect table API overview:
- mlx5_esw_indir_table_{init|destroy}() - init and destroy opaque indirect
table object.
- mlx5_esw_indir_table_get() - get or create new table according to vport
id and IP version. Table has following pre-created groups: recirculation
group with match on ethertype and VNI (rules that match encapsulated
packets are installed to this group) and forward group with default/miss
rule that forwards to vport of tunnel endpoint VF (rule for regular
non-encapsulated packets).
- mlx5_esw_indir_table_put() - decrease reference to the indirect table and
matching rule (for encapsulated traffic).
- mlx5_esw_indir_table_needed() - check that in_port is an uplink port and
out_port is VF on the same eswitch, verify that the rule is for IP traffic
and source port rewrite functionality can be used.
- mlx5_esw_indir_table_decap_vport() - function returns decap vport of
flow attribute.
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Refactor tun routing helpers to use dedicated struct
mlx5e_tc_tun_route_attr instead of multiple output arguments. This
simplifies the callers (no need to keep track of bunch of output param
pointers) and allows to unify struct release code in new
mlx5e_tc_tun_route_attr_cleanup() helper instead of requiring callers to
manually release some of the output parameters that require it.
Simplify code by unifying error handling at the end of the function and
rearranging code. Remove redundant empty line.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When tunnel endpoint is on VF, driver still assumes that endpoint is on
uplink and incorrectly configures encap rule offload according to that
assumption. As a result, traffic is sent directly to the uplink and rules
installed on representor of tunnel endpoint VF are ignored.
Implement following changes to allow offloading tx traffic with tunnel
endpoint on VF:
- For tunneling flows perform route lookup on route and out devices pair.
If out device is uplink and route device is VF of same physical port, then
modify packet reg_c_0 metadata register (source port) with the value of VF
vport. Use eswitch vhca_id->vport mapping introduced in one of previous
patches in the series to obtain vport from route netdevice.
- Recirculate encapsulated packets to VF vport in order to apply any flow
rules installed on VF representor that match on encapsulated traffic.
Only enable support for this functionality when all following conditions
are true:
- Hardware advertises capability to preserve reg_c_0 value on packet
recirculation.
- Vport metadata matching is enabled.
- Termination tables are to be used by the flow.
Example TC rules for VF tunnel traffic:
1. Rule that redirects packets from UL to VF rep that has the tunnel
endpoint IP address:
$ tc -s filter show dev enp8s0f0 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac 16:c9:a0:2d:69:2c
src_mac 0c:42:a1:58:ab:e4
eth_type ipv4
ip_flags nofrag
in_hw in_hw_count 1
action order 1: mirred (Egress Redirect to device enp8s0f0_0) stolen
index 3 ref 1 bind 1 installed 377 sec used 0 sec
Action statistics:
Sent 114096 bytes 952 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 114096 bytes 952 pkt
backlog 0b 0p requeues 0
cookie 878fa48d8c423fc08c3b6ca599b50a97
no_percpu
used_hw_stats delayed
2. Rule that decapsulates the tunneled flow and redirects to destination VF
representor:
$ tc -s filter show dev vxlan_sys_4789 ingress
filter protocol ip pref 4 flower chain 0
filter protocol ip pref 4 flower chain 0 handle 0x1
dst_mac ca:2e:a7:3f:f5:0f
src_mac 0a:40:bd:30:89:99
eth_type ipv4
enc_dst_ip 7.7.7.5
enc_src_ip 7.7.7.1
enc_key_id 98
enc_dst_port 4789
enc_tos 0
ip_flags nofrag
in_hw in_hw_count 1
action order 1: tunnel_key unset pipe
index 2 ref 1 bind 1 installed 434 sec used 434 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 2: mirred (Egress Redirect to device enp8s0f0_1) stolen
index 4 ref 1 bind 1 installed 434 sec used 0 sec
Action statistics:
Sent 129936 bytes 1082 pkt (dropped 0, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 129936 bytes 1082 pkt
backlog 0b 0p requeues 0
cookie ac17cf398c4c69e4a5b2f7aabd1b88ff
no_percpu
used_hw_stats delayed
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in the series extend forwarding functionality with VF
tunnel TX and RX handling. Extract action forwarding processing code into
dedicated functions to simplify further extensions:
- Handle every forwarding case with dedicated function instead of inline
code.
- Extract forwarding dest dispatch conditional into helper function
esw_setup_dests().
- Unify forwaring cleanup code in error path of
mlx5_eswitch_add_offloaded_rule() and in rule deletion code of
__mlx5_eswitch_del_rule() in new helper function esw_cleanup_dests() (dual
to new esw_setup_dests() helper).
This patch does not change functionality.
Co-developed-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Eswitch offloads extensions in following patches in the series require
attr->esw_attr->in_mdev pointer to always be set. This is already the case
for all code paths except mlx5_tc_ct_entry_add_rule() function. Fix the
function to assign mdev pointer with priv->mdev value.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patches in the series need to be able to map VF netdev to vport.
Since it is trivial to obtain vhca_id from netdev, maintain mapping from
vhca_id to vport_num inside eswitch offloads using xarray. Provide function
mlx5_eswitch_vhca_id_to_vport() to be used by TC code in following patches
to obtain the mapping.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Setting the source port requires only the E-Switch and vport number.
Refactor the function to get those parameters instead of passing the full
attribute.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When disable CBS, mode_to_use parameter is not updated even the operation
mode of Tx Queue is changed to Data Centre Bridging (DCB). Therefore,
when tc_setup_cbs() function is called to re-enable CBS, the operation
mode of Tx Queue remains at DCB, which causing CBS fails to work.
This patch updates the value of mode_to_use parameter to MTL_QUEUE_DCB
after operation mode of Tx Queue is changed to DCB in stmmac_dma_qmode()
callback function.
Fixes: 1f705bc61a ("net: stmmac: Add support for CBS QDISC")
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Link: https://lore.kernel.org/r/1612447396-20351-1-git-send-email-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The XDP frame's headroom might be large enough to accommodate the
xdpf backpointer as well as shifting the data to an aligned address.
Try this first before resorting to allocating a new buffer and copying
the data.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 256 byte data alignment is required for preventing DMA transaction
splits when crossing 4K page boundaries. Since XDP deals only with page
sized buffers or less, this restriction isn't needed. Instead, the data
only needs to be aligned to 64 bytes to prevent DMA transaction splits.
These lessened restrictions can increase performance by widening the pool
of permitted data alignments and preventing unnecessary realignments.
Fixes: ae680bcbd0 ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the erratum workaround is triggered, the newly created xdp_frame
structure is stored at the start of the newly allocated buffer. Avoid
the structure from being overwritten by explicitly reserving enough
space in the buffer for storing it.
Account for the fact that the structure's size might increase in time by
aligning the headroom to DPAA_FD_DATA_ALIGNMENT bytes, thus guaranteeing
the data's alignment.
Fixes: ae680bcbd0 ("dpaa_eth: implement the A050385 erratum workaround for XDP")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The check for a NULL pf pointer is moot since the earlier declaration and
assignment of struct device *dev already de-referenced the pointer. Also,
the only caller of ice_set_dflt_mib() already ensures pf is not NULL.
Cc: Dave Ertman <david.m.ertman@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the flex_array_size() helper with the recently added flexible array
members in structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Refactor the code according to the use of a flexible-array member in
struct ice_res_tracker, instead of a one-element array and use the
struct_size() helper to calculate the size for the allocations.
Also, notice that the code below suggests that, currently, two too many
bytes are being allocated with devm_kzalloc(), as the total number of
entries (pf->irq_tracker->num_entries) for pf->irq_tracker->list[] is
_vectors_ and sizeof(*pf->irq_tracker) also includes the size of the
one-element array _list_ in struct ice_res_tracker.
drivers/net/ethernet/intel/ice/ice_main.c:3511:
3511 /* populate SW interrupts pool with number of OS granted IRQs. */
3512 pf->num_avail_sw_msix = (u16)vectors;
3513 pf->irq_tracker->num_entries = (u16)vectors;
3514 pf->irq_tracker->end = pf->irq_tracker->num_entries;
With this change, the right amount of dynamic memory is now allocated
because, contrary to one-element arrays which occupy at least as much
space as a single object of the type, flexible-array members don't
occupy such space in the containing structure.
[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.9-rc1/process/deprecated.html#zero-length-and-one-element-arrays
Built-tested-by: kernel test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Just as we recently added support for other stored firmware flash
versions, support display of the stored UNDI Option ROM version via
devlink info.
To do this, we need to introduce a new ice_get_inactive_orom_ver
function. This is a little trickier than with other flash versions. The
Option ROM version data was being read from a special "Boot
Configuration" block of the NVM Preserved Field Area. This block only
contains the *active* Option ROM version data. It is populated when the
device firmware finishes updating the Option ROM.
This method is ineffective at reading the stored Option ROM version
data. Instead of reading from this section of the flash, replace this
version extraction with one which locates the Combo Version information
from within the Option ROM binary.
This data is stored within the Option ROM at a 512 byte offset, in
a simple structured format. The structure uses a simple modulo 256
checksum for integrity verification. Scan through the Option ROM to
locate the CIVD data section, and extract the Combo Version.
Refactor ice_get_orom_ver_info so that it takes the bank select
enumeration parameter. Use this to implement ice_get_inactive_orom_ver.
Although all ice devices have a Boot Configuration block in the NVM PFA,
not all devices have a valid Option ROM. In this case, the old
ice_get_orom_ver_info would "succeed" but report a version of all
zeros. The new implementation would fail to locate the $CIV section in
the Option ROM and report an error. Thus, we must ensure that
ice_init_nvm does not fail if ice_get_orom_ver_info fails.
Use the new ice_get_inactive_orom_ver to allow reporting the Option ROM
versions for a pending update via devlink info.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a function to read the inactive netlist bank for version
information. To support this, refactor how we read the netlist version
data. Instead of using the firmware AQ interface with a module ID, read
from the flash as a flat NVM, using ice_read_flash_module.
This change requires a slight adjustment to the offset values used, as
reading from the flat NVM includes the type field (which was stripped by
firmware previously). Cleanup the macro names and move them to
ice_type.h. For clarity in how we calculate the offsets and so that
programmers can easily map the offset value to the data sheet, use
a wrapper macro to account for the offset adjustments.
Use the newly added ice_get_inactive_netlist_ver function to extract the
version data from the pending netlist module update. Add the stored
variants of "fw.netlist", and "fw.netlist.build" to the info version map
array.
With this change, we now report the "fw.netlist" and "fw.netlist.build"
versions into the stored section of the devlink info report. As with the
main NVM module versions, if there is no pending update, we report the
currently active values as stored.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The devlink info interface supports drivers reporting "stored" versions.
These versions indicate the version of an update that has been
downloaded to the device, but is not yet active.
The code for extracting the NVM version recently changed to enable
support for reading from either the active or the inactive bank. Use
this to implement ice_get_inactive_nvm_ver, which will read the NVM
version data from the inactive section of flash.
When reporting the versions via devlink info, first read the device
capabilities. Determine if there is a pending flash update, and if so,
extract relevant version information from the inactive flash. Store
these within the info context structure.
When reporting "stored" firmware versions, devlink documentation
indicates that we ought to always report a stored value, even if there
is no pending update. In this common case, the stored version should
match the running version. This means that each stored version should by
default fallback to the same value as reported by the running handler.
To support this, modify the version structure to have both a "getter"
and a "fallback". Modify the control loop so that it will use the
"fallback" function if the "getter" function does not report a version.
To report versions for which we can read the stored value, use a new
"stored()" macro. This macro will insert two entries into the version
list. The first entry is the traditional running version. The second is
the stored version, implemented with a fallback to the active version.
This is a little tricky, but reduces the overall duplication of elements
in the entry list, and ensures that running and stored values remain
consistent.
To avoid some duplication, add a combined() macro that will insert both
the running and stored versions into the version entry list.
Using this new support, add pending version reporter functions for
"fw.psid.api" and "fw.bundle_id". This enables reporting the stored
values for some of versions in the NVM module of the flash.
Reporting management versions is not implemented by this patch. The
active management version is reported to the driver via the AdminQ
mailbox during load. Although the version must be in the firmware binary
somewhere, accessing this from the inactive firmware is not trivial and
has not been implemented in this change.
Future changes will introduce support for reading the UNDI Option ROM
version and the version associated with the Netlist module.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When reading from the flash memory of the device, the ice driver has two
interfaces available to it. First, it can use a mediated interface via
firmware that allows specifying a module ID. This allows reading from
specific modules of the active flash bank.
The second interface available is to perform flat reads. This allows
complete access to the entire flash. However, using it requires the
software to handle calculating module location and interpret pointer
addresses.
While most data required is accessible through the convenient first
interface, certain flash contents are not. This includes the CSS header
information associated with the Option ROM and NVM banks, as well as any
access to the "inactive" banks used as scratch space for performing
flash updates.
In order to access all of the relevant flash contents, software must use
the flat reads. Rather than forcing all flows to perform flat read
calculations, introduce a new abstraction for reading from the flash:
ice_read_flash_module. This function provides an abstraction for reading
from either the active or inactive flash bank at the requested module.
This interface is very similar to the abstraction provided via firmware,
but allows access to additional modules, as well as providing
a mechanism to request access to both flash banks.
At first glance, it might make sense for this abstraction to allow
specifying precisely which bank (1st or 2nd) the caller wishes to read.
This is simpler to implement but more difficult to use. In practice,
most callers only know whether they want the active bank, or the
inactive bank. Rather than force callers to determine for themselves
which bank to read from, implement ice_read_flash_module in terms of
"active" vs "inactive". This significantly simplifies the implementation
at the caller level and is a more useful abstraction over the flash
contents.
Make use of this new interface to refactor reading of the main NVM
version information. Instead of using the firmware's mediated ShadowRAM
function, use the ice_read_flash_module abstraction.
To do this, notice that most reads of the NVM are going to be in 2-byte
word chunks. To simplify using ice_read_flash_module for this case,
ice_read_nvm_module is introduced. This is a simple wrapper around
ice_read_flash_module which takes the correct pointer address for the
NVM bank, and forces the 2-byte word format onto the caller.
When reading the NVM versions, some fields are read from the Shadow RAM.
The Shadow RAM is the first 64KB of flash memory, and is populated
during device load. Most fields are copied from a section within the
active NVM bank. In order to read this data from both the active and
inactive NVM banks, we need to read not from the first 64KB of flash,
but instead from the correct offset into the NVM bank. Introduce
ice_read_nvm_sr_copy for this purpose. This function wraps around
ice_read_nvm_module and has the same interface as the ice_read_sr_word,
with the exception of allowing the caller to specify whether to read the
active or inactive flash bank.
With this change, it is now trivial to refactor ice_get_nvm_ver_info to
read using the software mediated ice_read_flash_module interface instead
of relying on the firmware mediated interface. This will be used in the
following change to implement support for stored versions in the devlink
info report.
Additionally, the overall ice_read_flash_module interface will be used
and extended to support all three major flash banks, and additionally to
support reading the flash image security revision information.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice flash contains two copies of each of the NVM, Option ROM, and
Netlist modules. Each bank has a pointer word and a size word. In order
to correctly read from the active flash bank, the driver must calculate
the offset manually.
During NVM initialization, read the Shadow RAM control word and
determine which bank is active for each NVM module. Additionally, cache
the size and pointer values for use in calculating the correct offset.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver uses an array of structures which link an info name with
a function that formats the associated version data into a string.
All existing format functions simply format already captured static data
from the driver hw structure. Future changes will introduce format
functions for reporting the versions of flash sections stored but not
yet applied. This type of version data is not stored as a member of the
hw structure. This is because (a) it might not yet exist in the case
there is no pending flash update, and (b) even if it does, it might
change such as if an update is canceled or replaced by a new update
before finalizing.
We could simply have each format function gather its own data upon being
called. However, in some cases the raw binary version data is
a combination of multiple different reported fields. Additionally, the
current interface doesn't have a way for the function to indicate that
the version doesn't exist.
Refactor this function interface to take a new ice_info_ctx structure
instead of the buffer pointer and length. This context structure allows
for future extensions to pre-gather version data that is stored within
the context struct instead of the hw struct.
Allocate this context structure initially at the start of
ice_devlink_info_get. We use dynamic allocation instead of a local stack
variable in order to avoid using too much kernel stack once we extend it
with additional data structures.
Modify the main loop that drives the info reporting so that the version
buffer string is always cleared between each format. Explicitly check
that the format function actually filled in a version string of non-zero
length. If the string is not provided, simply skip this version without
reporting an error. This allows for introducing format functions of
versions which may or may not be present, such as the version of
a pending update that has not yet been activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_nvm_info structure has become somewhat of a dumping ground for
all of the fields related to flash version. It holds the NVM version and
EETRACK id, the OptionROM info structure, the flash size, the ShadowRAM
size, and more.
A future change is going to add the ability to read the NVM version and
EETRACK ID from the inactive NVM bank. To make this simpler, it is
useful to have these NVM version info fields extracted to their own
structure.
Rename ice_nvm_info into ice_flash_info, and create a separate
ice_nvm_info structure that will contain the eetrack and NVM map
version. Move the netlist_ver structure into ice_flash_info and rename it
ice_netlist_info for consistency.
Modify the static ice_get_orom_ver_info to take the option rom structure
as a pointer. This makes it more obvious what portion of the hw struct
is being modified. Do the same for ice_get_netlist_ver_info.
Introduce a new ice_get_nvm_ver_info function, which will be similar to
ice_get_orom_ver_info and ice_get_netlist_ver_info, used to keep the NVM
version extraction code co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When erasing, notify userspace of how long we will potentially take to
erase a module. Doing so allows userspace to report the timeout, giving
a clear indication of the upper time bound of the operation.
Since we're re-using the erase timeout value, make it a macro rather
than a magic number.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-02-03
This series contains updates to igc, igb, e1000e, and e1000 drivers.
Sasha adds counting of good transmit packets and reporting of NVM version
and gPHY version in ethtool firmware version. Replaces the use of strlcpy
to the preferred strscpy. Fixes a typo that caused the wrong register to be
output. He also removes an unused function pointer, some unneeded defines,
and a non-applicable comment. All changes for igc.
Gal Hammer fixes a typo which caused the RDBAL register values to be
shown instead of TDBAL for igb.
Nick Lowe enables RSS support for i211 devices for igb.
Tom Rix fixes checkpatch warning by removing h from printk format
specifier for igb.
Kaixu Xia removes setting of a variable that is overwritten before next
use for e1000e.
Sudip Mukherjee removes an unneeded assignment for e1000.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000: drop unneeded assignment in e1000_set_itr()
e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt
igb: remove h from printk format specifier
igb: Enable RSS for Intel I211 Ethernet Controller
igb: fix TDBAL register show incorrect value
igc: Fix TDBAL register show incorrect value
igc: Remove unused FUNC_1 mask
igc: Remove unused local receiver mask
igc: Prefer strscpy over strlcpy
igc: Expose the gPHY firmware version
igc: Expose the NVM version
igc: Add Host Good Packets Transmitted Count
igc: Remove MULR mask define
igc: Remove igc_set_fw_version comment
igc: Clean up nvm_operations structure
====================
Link: https://lore.kernel.org/r/20210204004259.3662059-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael tried to enable Advanced Error Reporting through the ENETC's
Root Complex Event Collector, and the system started spitting out single
bit correctable ECC errors coming from the ENETC interfaces:
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
fsl_enetc 0000:00:00.0: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.0: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.0: [14] CorrIntErr
fsl_enetc 0000:00:00.1: PCIe Bus Error: severity=Corrected, type=Transaction Layer, (Receiver ID)
fsl_enetc 0000:00:00.1: device [1957:e100] error status/mask=00004000/00000000
fsl_enetc 0000:00:00.1: [14] CorrIntErr
Further investigating the port correctable memory error detect register
(PCMEDR) shows that these AER errors have an associated SOURCE_ID of 6
(RFS/RSS):
$ devmem 0x1f8010e10 32
0xC0000006
$ devmem 0x1f8050e10 32
0xC0000006
Discussion with the hardware design engineers reveals that on LS1028A,
the hardware does not do initialization of that RFS/RSS memory, and that
software should clear/initialize the entire table before starting to
operate. That comes as a bit of a surprise, since the driver does not do
initialization of the RFS memory. Also, the initialization of the
Receive Side Scaling is done only partially.
Even though the entire ENETC IP has a single shared flow steering
memory, the flow steering service should returns matches only for TCAM
entries that are within the range of the Station Interface that is doing
the search. Therefore, it should be sufficient for a Station Interface
to initialize all of its own entries in order to avoid any ECC errors,
and only the Station Interfaces in use should need initialization.
There are Physical Station Interfaces associated with PCIe PFs and
Virtual Station Interfaces associated with PCIe VFs. We let the PF
driver initialize the entire port's memory, which includes the RFS
entries which are going to be used by the VF.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210204134511.2640309-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The null check of filp->f_path.dentry->d_iname is redundant because
it is an array of DNAME_INLINE_LEN chars and cannot be a null. Fix
this by removing the null check.
Addresses-Coverity: ("Array compared against 0")
Fixes: 04987ca1b9 ("net: hns3: add debugfs support for tm nodes, priority and qset info")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20210203131040.21656-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now we can remove a bunch of identical functions from the drivers and
make them use common dev_page_is_reusable(). All {,un}likely() checks
are omitted since it's already present in this helper.
Also update some comments near the call sites.
Suggested-by: David Rientjes <rientjes@google.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when user space queries the link's parameters, as speed and
duplex, each parameter is passed from the driver to ethtool.
Instead, pass the link mode bit in use.
In Spectrum-1, simply pass the bit that is set to '1' from PTYS register.
In Spectrum-2, pass the first link mode bit in the mask of the used
link mode.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when auto negotiation is set to off, the user can force a
specific speed or both speed and duplex. The user cannot influence the
number of lanes that will be forced.
Add support for setting speed along with lanes so one would be able
to choose how many lanes will be forced.
When lanes parameter is passed from user space, choose the link mode
that its actual width equals to it.
Otherwise, the default link mode will be the one that supports the width
of the port.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when a speed can be supported by different number of lanes,
the supported link modes bitmask contains only link modes with a single
number of lanes.
This was done in order to prevent auto negotiation on number of
lanes after 50G-1-lane and 100G-2-lanes link modes were introduced.
For example, if a port's max width is 4, only link modes with 4 lanes
will be presented as supported by that port, so 100G is always achieved by
4 lanes of 25G.
After the previous patches that allow selection of the number of lanes,
auto negotiation on number of lanes becomes practical.
Remove that filtering of the maximum number of lanes supported link modes,
so indeed all the supported and advertised link modes will be shown.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
t1_fatal_err() is invoked from the interrupt handler. The bad part is
that it invokes (via t1_sge_stop()) del_timer_sync() and tasklet_kill().
Both functions must not be called from an interrupt because it is
possible that it will wait for the completion of the timer/tasklet it
just interrupted.
In case of a fatal error, use t1_interrupts_disable() to disable all
interrupt sources and then wake the interrupt thread with
F_PL_INTR_SGE_ERR as pending flag. The threaded-interrupt will stop the
card via t1_sge_stop() and not re-enable the interrupts again.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The external interrupt (F_PL_INTR_EXT) needs to be handled in a process
context and this is accomplished by utilizing a workqueue.
The process context can also be provided by a threaded interrupt instead
of a workqueue. The threaded interrupt can be used later for other
interrupt related processing which require non-atomic context without
using yet another workqueue. free_irq() also ensures that the thread is
done which is currently missing (the worker could continue after the
module has been removed).
Save pending flags in pending_thread_intr. Use the same mechanism
to disable F_PL_INTR_EXT as interrupt source like it is used before the
worker is scheduled. Enable the interrupt again once
t1_elmer0_ext_intr_handler() is done.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleans up all resources
attached to that VF. This patch adds support to handle
CPT FLR.
Signed-off-by: Narayana Prasad Raju Atherya <pathreya@marvell.com>
Signed-off-by: Suheil Chandran <schandran@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch changes CPT mailbox message format to
support new block CPT1 in 98xx silicon.
cpt_rd_wr_reg ->
Modify cpt_rd_wr_reg mailbox and its handler to
accommodate new block CPT1.
cpt_lf_alloc ->
Modify cpt_lf_alloc mailbox and its handler to
configure LFs from a block address out of multiple
blocks of same type. If a PF/VF needs to configure
LFs from both the blocks then this mbox should be
called twice.
Signed-off-by: Mahipal Challa <mchalla@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable 'current_itr' is assigned to 0 before jumping to
'set_itr_now' but it has not been used after the jump. So, remove the
unneeded assignment.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Both of the statements are value assignment of the variable act_offset.
The first value assignment is overwritten by the second and is useless.
Remove it.
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This change fixes the checkpatch warning described in this
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS)
queues. It should not be excluded from having this feature enabled.
Via commit c883de9fd7 ("igb: rename igb define to be more generic")
E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to
indicate that this is a generic bit flag to enable queues and not
a flag that is specific to devices that support 4 queues
The bit flag enables 2, 4 or 8 queues appropriately depending on the part.
Tested with a multicore CPU and frames were then distributed as expected.
This issue appears to have been introduced because of confusion caused
by the prior name.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fixed a typo which caused the registers dump function to read the
RDBAL register when printing TDBAL register values.
_reg_dump method has been partially derived from i210 and have
same typo.
Suggested-by: Gal Hammer <ghammer@redhat.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe should return an error code if platform_get_irq_byname() fails
but it returns success instead.
Fixes: 6c30384eb1 ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXyFIl4V9hgxYM@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are several error handling bugs in mscc_ocelot_init_ports(). I
went through the code, and carefully audited it and made fixes and
cleanups.
1) The ocelot_probe_port() function didn't have a mirror release function
so it was hard to follow. I created the ocelot_release_port()
function.
2) In the ocelot_probe_port() function, if the register_netdev() call
failed, then it lead to a double free_netdev(dev) bug. Fix this by
setting "ocelot->ports[port] = NULL" on the error path.
3) I was concerned that the "port" which comes from of_property_read_u32()
might be out of bounds so I added a check for that.
4) In the original code if ocelot_regmap_init() failed then the driver
tried to continue but I think that should be a fatal error.
5) If ocelot_probe_port() failed then the most recent devlink was leaked.
The fix for mostly came Vladimir Oltean. Get rid of "registered_ports"
and just set a bit in "devlink_ports_registered" to say when the
devlink port has been registered (and needs to be unregistered on
error). There are fewer than 32 ports so a u32 is large enough for
this purpose.
6) The error handling if the final ocelot_port_devlink_init() failed had
two problems. The "while (port-- >= 0)" loop should have been
"--port" pre-op instead of a post-op to avoid a buffer underflow.
The "if (!registered_ports[port])" condition was reversed leading to
resource leaks and double frees.
Fixes: 6c30384eb1 ("net: mscc: ocelot: register devlink ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/YBkXhqRxHtRGzSnJ@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FUNC_1 mask not in use in i225 device and could be removed
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Local receiver mask SR_1000T_LOCAL_RX_STATUS not in use in i225 device
and could be removed
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use the strscpy method instead of strlcpy method.
See: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr
_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Extend reporting of NVM image version to include the gPHY (i225 PHY)
firmware version.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Expose the NVM map version via drvinfo in ethtool
NVM image version is reported as firmware version for i225 device
Minor typo fix - remove space
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This counter counts the number of good (non-erred) packets
transmitted sent by the host.
A good transmit packet is considered one that is 64 or more bytes
in length (from <Destination Address> through <CRC>,
inclusively) in length
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Multiple Tx Data Read Requests is hardware pipeline feature and
is not controlled by software
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 device not supported and do not plan to support
configuration of fw version string for ethtool
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
valid_led_default function pointer not in use and can
be removed from nvm_operations structure.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
According to the vendor driver, the new chip with XID 0x54b is
essentially the same as the one with XID 0x54a, but it doesn't need the
firmware.
So add support accordingly.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210202044813.1304266-1-kai.heng.feng@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the next patch mlxsw and netdevsim will fail in compilation if
CONFIG_IPV6 is disabled.
Do not call fib6_info_hw_flags_set() when IPv6 is disabled.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The next patch will emit notification when hardware flags are changed,
in case that fib_notify_on_flag_change sysctl is set to 1.
To know sysctl values, net struct is needed.
This change is consistent with the IPv4 version, which gets 'net' struct
as its first argument.
Currently, the only callers of this function are mlxsw and netdevsim.
Patch the callers to pass net.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmAY+OoACgkQSD+KveBX
+j6hPAf9G09tOYaZfFkbFmfhe5TnjwPCf/2CdErj+dEPb9GI6rYhVoSYeNqUZSt0
UYQeutWVSaIohCA79D8l1PFHlOV1CXYO35BGi7Ga6glODzXEDEt0u/kqxAH7eNuF
VsnxQ2kfzDwN2M8N2xuIzoG66I+IAFa9hukzxLcIPwYjbGDL46p54wNZVSCh/scu
7CJbpTXTBh9yLRWTfhVouTWMHu3DaC7rMnaB+Yq+lRRzqnQ6Xitdty6uvFSKMv1Y
CMVuVKH3dafCFhJf/xF7vwdlGo4QcVx2FbZwo0I6tjGEEzYwfCWAaqY+3MB0VRc5
k7tjJeT6T+MW29knSh71LmTrnm/Abg==
=FWcp
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2021-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-02-01
Please note the first patch in this series
("Fix function calculation for page trees") is fixing a regression
due to previous fix in net which you didn't include in your previous
rc pr. So I hope this series will make it into your next rc pr,
so mlx5 won't be broken in the next rc.
* tag 'mlx5-fixes-2021-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Release skb in case of failure in tc update skb
net/mlx5e: Update max_opened_tc also when channels are closed
net/mlx5: Fix leak upon failure of rule creation
net/mlx5: Fix function calculation for page trees
====================
Link: https://lore.kernel.org/r/20210202070703.617251-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far phy_disconnect() is called before free_irq(). If CONFIG_DEBUG_SHIRQ
is set and interrupt is shared, then free_irq() creates an "artificial"
interrupt by calling the interrupt handler. The "link change" flag is set
in the interrupt status register, causing phylib to eventually call
phy_suspend(). Because the net_device is detached from the PHY already,
the PHY driver can't recognize that WoL is configured and powers down the
PHY.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/fe732c2c-a473-9088-3974-df83cfbd6efd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Last TCAM data contains TCAM enable bit.
It should be written after SRAM data before entry enabled.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Link: https://lore.kernel.org/r/1612172139-28343-1-git-send-email-stefanc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case of failure in tc update skb the packet is dropped
without freeing the skb.
Fixed by freeing the skb in case failure in tc update skb.
Fixes: d6d2778286 ("net/mlx5: E-Switch, Restore chain id on miss")
Fixes: c756909722 ("net/mlx5e: Add tc chains offload support for nic flows")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
max_opened_tc is used for stats, so that potentially non-zero stats
won't disappear when num_tc decreases. However, mlx5e_setup_tc_mqprio
fails to update it in the flow where channels are closed.
This commit fixes it. The new value of priv->channels.params.num_tc is
always checked on exit. In case of errors it will just be the old value,
and in case of success it will be the updated value.
Fixes: 05909babce ("net/mlx5e: Avoid reset netdev stats on configuration changes")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When creation of a new rule that requires allocation of an FTE fails,
need to call to tree_put_node on the FTE in order to release its'
resource.
Fixes: cefc23554f ("net/mlx5: Fix FTE cleanup")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The function calculation always results in a value of 0. This works
generally, but when the release all pages feature is enabled it will
result in crashes.
Fixes: 0aa128475d ("net/mlx5: Maintain separate page trees for ECPF and PF functions")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If as part of the actions the TTL of the packet is modified, the packet's
checksum needs to be recalculated. Connect-X6DX can handle this csum
recalculation natively. Older devices require this additional recalculation.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The TLS RX workqueue is needed only when kTLS RX device offload
is supported.
Move its creation from the general TLS init function to the
kTLS RX init.
Create it once at init time if supported, avoid creation/destroy
everytime the feature bit is toggled.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This change fixes the checkpatch warning described in this commit
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]")
Standard integer promotion is already done and %hx and %hhx is useless
so do not encourage the use of %hh[xudi] or %h[xudi].
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shay Drory