Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA
controller found in the MSM8x60 and IPQ/APQ8064 platforms.
The ADM supports both memory to memory transactions and memory
to/from peripheral device transactions. The controller also provides
flow control capabilities for transactions to/from peripheral devices.
The initial release of this driver supports slave transfers to/from
peripherals and also incorporates CRCI (client rate control interface)
flow control.
The hardware only supports a 32 bit physical address, so specifying
!PHYS_ADDR_T_64BIT gives maximum COMPILE_TEST coverage without having to
spend effort on kludging things in the code that will never actually be
needed on real hardware.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201114140233.GM32650@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The error codes were not set on some of these error paths.
Also the error handling was more confusing than it needed to be so I
cleaned it up and shuffled it around a bit.
Fixes: d2fb0a0438 ("dmaengine: break out channel registration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201113101631.GE168908@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201116202403.29749-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 7f832645d0 ("dmaengine: ioatdma: remove ioatdma v2 registration")
missed to remove dca2_tag_map_valid() during its removal. Hence, since
then, dca2_tag_map_valid() is unused and make CC=clang W=1 warns:
drivers/dma/ioat/dca.c:44:19:
warning: unused function 'dca2_tag_map_valid' [-Wunused-function]
So, remove this unused function and get rid of a -Wused-function warning.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113081248.26416-1-lukas.bulwahn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Portal size is 4k. Current code is mapping all 4 portals in a single chunk.
Restrict the mapped portal size to a single portal to ensure that submission
only goes to the intended portal address.
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160513342642.510187.16450549281618747065.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We now use cpu_pm for saving and restoring device context for deeper SoC
idle states. But for omap3, we must also block idle if SDMA is busy.
If we don't block idle when SDMA is busy, we eventually end up saving and
restoring SDMA register state on PER domain idle while SDMA is active and
that causes at least audio playback to fail.
Fixes: 4c74ecf792 ("dmaengine: ti: omap-dma: Add device tree match data and use it for cpu_pm")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201109154013.11950-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SG capability is inherently present with Multichannel DMA operation.
The register used to check for this capability with other DMA driver types
is not defined for MCDMA.
Fixes: 6ccd692bfb ("dmaengine: xilinx_dma: Add Xilinx AXI MCDMA Engine driver support")
Signed-off-by: Matthew Murrian <matthew.murrian@goctsi.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1604473206-32573-4-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Several code sections incorrectly use struct xilinx_axidma_tx_segment
instead of struct xilinx_aximcdma_tx_segment when operating as
Multichannel DMA. As their structures are similar, this just works.
Fixes: 6ccd692bfb ("dmaengine: xilinx_dma: Add Xilinx AXI MCDMA Engine driver support")
Signed-off-by: Matthew Murrian <matthew.murrian@goctsi.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1604473206-32573-3-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The xilinx_dma_poll_timeout macro is sometimes called while holding a
spinlock (see xilinx_dma_issue_pending() for an example) this means we
shouldn't sleep when polling the dma channel registers. To address it
in xilinx poll timeout macro use readl_poll_timeout_atomic instead of
readl_poll_timeout variant.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1604473206-32573-2-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Link: https://lore.kernel.org/r/20201027215252.25820-11-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201027215252.25820-10-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-9-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-8-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-7-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-6-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://lore.kernel.org/r/20201027215252.25820-5-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Cc: Green Wan <green.wan@sifive.com>
Link: https://lore.kernel.org/r/20201027215252.25820-4-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201027215252.25820-3-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-2-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The NAVSS UDMA will stuck if target IP module is disabled by PM while PSI-L
threads are paired UDMA<->IP and no further transfers is possible. This
could be the case for IPs J721E Main CPSW (cpsw9g).
Hence, to avoid such situation do PSI-L threads pairing only when UDMA
channel is going to be enabled as at this time DMA consumer module expected
to be active already.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201030203000.4281-1-grygorii.strashko@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When consumer requests channel power on the DMA controller device
and otherwise on the freeing channel resources.
Note, in some cases consumer acquires channel at the ->probe() stage and
releases it at the ->remove() stage. It will mean that DMA controller device
will be powered during all this time if there is no assist from hardware
to idle it. The above mentioned cases should be investigated separately
and individually.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20201103183938.64752-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add code to "complete" a descriptor when the descriptor or its completion
address hit a fault error when SVA mode is being used. This error can be
triggered due to bad programming by the user. A lock is introduced in order
to protect the descriptor completion lists since the fault handler will run
from the system work queue after being scheduled in the interrupt handler.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160382008092.3911367.12766483427643278985.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add shared workqueue support that includes the support of Shared Virtual
memory (SVM) or in similar terms On Demand Paging (ODP). The shared
workqueue uses the enqcmds command in kernel and will respond with retry if
the workqueue is full. Shared workqueue only works when there is PASID
support from the IOMMU.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160382007499.3911367.26043087963708134.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The xor_hw_desc local variable is assigned but never read:
drivers/dma/ppc4xx/adma.c: In function ‘ppc440spe_desc_set_src_mult’:
drivers/dma/ppc4xx/adma.c:562:17: warning: variable ‘xor_hw_desc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201019155756.21445-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ppc440spe_adma_chan_list file-scope variable is not used outside of
the unit so it can be made static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201019155756.21445-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sama7g5 version of the XDMAC supports priority configuration and
outstanding capabilities.
Add defines for the specific registers for this configuration, together
with recommended settings.
However the settings are very different if the XDMAC is a mem2mem or a
per2mem controller.
Thus, we need to differentiate according to device tree property.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20201016093918.290137-1-eugen.hristev@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SAMA7G5 SoC uses a slightly different variant of the AT_XDMAC.
Added support by a new compatible and a layout struct that copes
to the specific version considering the compatible string.
Only the differences in register map are present in the layout struct.
I reworked the register access for this part that has the differences.
Also the Source/Destination Interface bits are no longer valid for this
variant of the XDMAC. Thus, the layout also has a bool for specifying
whether these bits are required or not.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20201016093850.290053-1-eugen.hristev@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PERID in the CC register for mem2mem operations must match an unused
PERID.
The PERID field is 7 bits, but the selected value is 0x3f.
On later products we can have more reserved PERIDs for actual peripherals,
thus this needs to be increased to maximum size.
Changing the value to 0x7f, which is the maximum for 7 bits field.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201016093725.289880-1-eugen.hristev@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make use of the new struct_size() helper instead of the offsetof() idiom.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20201008141828.GA20325@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch removes the MIC drivers from the kernel tree
since the corresponding devices have been discontinued.
Removing the dma and char-misc changes in one patch and
merging via the char-misc tree is best to avoid any
potential build breakage.
Cc: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/8c1443136563de34699d2c084df478181c205db4.1603854416.git.sudeep.dutt@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc warns about a mismatch argument type when passing
'false' into a function that expects an enum:
drivers/dma/ti/k3-udma-private.c: In function 'xudma_tchan_get':
drivers/dma/ti/k3-udma-private.c:86:34: warning: implicit conversion from 'enum <anonymous>' to 'enum udma_tp_level' [-Wenum-conversion]
86 | return __udma_reserve_##res(ud, false, id); \
| ^~~~~
drivers/dma/ti/k3-udma-private.c:95:1: note: in expansion of macro 'XUDMA_GET_PUT_RESOURCE'
95 | XUDMA_GET_PUT_RESOURCE(tchan);
| ^~~~~~~~~~~~~~~~~~~~~~
In this case, false has the same numerical value as
UDMA_TP_NORMAL, so passing that is most likely the correct
way to avoid the warning without changing the behavior.
Fixes: d702419134 ("dmaengine: ti: k3-udma: Add glue layer for non DMAengine users")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201026160123.3704531-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
Driver doesn't use keyword enum for enum owl_dmadesc_offsets resulting
in warning:
drivers/dma/owl-dma.c:139: warning: cannot understand function prototype:
'enum owl_dmadesc_offsets '
So add the keyword to fix it and also add documentation for missing
OWL_DMADESC_SIZE
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201007083113.567559-6-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit f19a11d40a ("dmaengine: xilinx: convert tasklets to use new
tasklet_setup() API") updated driver to use new tasklet_setup() API but
missed to update the documentation for the tasklet function.
Fixes: f19a11d40a ("dmaengine: xilinx: convert tasklets to use new tasklet_setup() API")
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20201007083113.567559-5-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit f19a11d40a ("dmaengine: xilinx: convert tasklets to use new
tasklet_setup() API") updated driver to use new tasklet_setup() API but
missed to update the documentation for the tasklet function.
Fixes: f19a11d40a ("dmaengine: xilinx: convert tasklets to use new tasklet_setup() API")
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20201007083113.567559-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 00c4747a2f ("dmaengine: qcom: convert tasklets to use new
tasklet_setup() API") updated driver to use new tasklet_setup() API but
missed to update the documentation for the tasklet function.
Fixes: 00c4747a2f ("dmaengine: qcom: convert tasklets to use new tasklet_setup() API")
Link: https://lore.kernel.org/r/20201007083113.567559-3-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 6752e40d66 ("dmaengine: altera-msgdma: convert tasklets to use
new tasklet_setup() API") updated driver to use new tasklet_setup() API
but missed to update the documentation for the tasklet function.
Fixes: 6752e40d66 ("dmaengine: altera-msgdma: convert tasklets to use new tasklet_setup() API")
Link: https://lore.kernel.org/r/20201007083113.567559-2-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Link: https://lore.kernel.org/r/20201006050458.221329-2-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Link: https://lore.kernel.org/r/20201006050458.221329-1-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(*x),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1600601186-7420-10-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(*x),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1600601186-7420-5-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_alloc_coherent() is called with a fixed SZ_2M size, but frees happen
with IOAT_CHUNK_SIZE. Recently, IOAT_CHUNK_SIZE was reduced to 512M but
the allocation did not change. To fix, change to using the
IOAT_CHUNK_SIZE define.
This was caught with the upcoming patchset for converting Intel platforms to the
dma-iommu implementation. It has a warning when the unmapped size differs from
the mapped size.
Fixes: a02254f8a6 ("dmaengine: ioat: Decreasing allocation chunk size 2M->512K")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/intel-gfx/776771a2-247a-d1be-d882-bee02d919ae0@deltatee.com/
Link: https://lore.kernel.org/r/20200922200844.2982-1-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200921093701.102208-1-zhangqilong3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 59cd818763 ("dmaengine: fsl: convert tasklets to use new
tasklet_setup() API") broke this driver by not removing the old channel
update method.
Fix this by remove the offending call as channel is queried from
tasklet structure.
Fixes: 59cd818763 ("dmaengine: fsl: convert tasklets to use new tasklet_setup() API")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201001164740.178977-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The jz4780_dma_tx_status() function would check if a channel's cookie
state was set to 'completed', and if not, it would enter the critical
section. However, in that time frame, the jz4780_dma_chan_irq() function
was able to set the cookie to 'completed', and clear the jzchan->vchan
pointer, which was deferenced in the critical section of the first
function.
Fix this race by checking the channel's cookie state after entering the
critical function and not before.
Fixes: d894fc6046 ("dmaengine: jz4780: add driver for the Ingenic JZ4780 DMA controller")
Cc: stable@vger.kernel.org # v4.0
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Link: https://lore.kernel.org/r/20201004140307.885556-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 59cd818763 ("dmaengine: fsl: convert tasklets to use new
tasklet_setup() API") converted the pl330 driver to use new tasklet
functions but missed that driver calls the tasklet function directly as
well, so update it.
Fixes: 59cd818763 ("dmaengine: fsl: convert tasklets to use new tasklet_setup() API")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200930121735.49699-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need to have a conditional for boolean expression when
function returns bool. Drop unnecessary code and return boolean
result directly.
While at it, drop unneeded casting from void *.
Cc: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200922115847.30100-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Andy reported that commit 6b41030fdc ("dmaengine: dmatest:
Restore default for channel") broke his scripts for the case
where "busy" channel is used for configuration with expectation
that run command would do nothing. Instead, behavior was
(unintentionally) changed to treat such case as under-configuration
and progress with defaults, i.e. run command would start a test
with default setting for channel (which would use all channels).
Restore original behavior with tracking status of channel setter
so we can distinguish between misconfigured and under-configured
cases in run command and act accordingly.
Fixes: 6b41030fdc ("dmaengine: dmatest: Restore default for channel")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200922115847.30100-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now the K3 UDMA glue layer enable functions perform RMW operation on UDMA
RX/TX RT_CTL registers to set EN bit and enable channel, which is
incorrect, because only EN bit has to be set in those registers to enable
channel (all other bits should be cleared 0).
More over, this causes issues when bootloader leaves UDMA channel RX/TX
RT_CTL registers in incorrect state - TDOWN bit set, for example. As
result, UDMA channel will just perform teardown right after it's enabled.
Hence, fix it by writing correct values (EN=1) directly in UDMA channel
RX/TX RT_CTL registers in k3_udma_glue_enable_tx/rx_chn() functions.
Fixes: d702419134 ("dmaengine: ti: k3-udma: Add glue layer for non DMAengine users")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200916120955.7963-1-grygorii.strashko@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
drivers/dma/iop-adma.c: In function ‘iop_adma_alloc_chan_resources’:
drivers/dma/iop-adma.c:447:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
hw_desc = (char *) iop_chan->device->dma_desc_pool;
^
drivers/dma/iop-adma.c:449:4: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t) &hw_desc[idx * IOP_ADMA_SLOT_SIZE];
^
drivers/dma/iop-adma.c: In function ‘iop_adma_probe’:
drivers/dma/iop-adma.c:1301:3: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *) adev->dma_desc_pool);
Use dma_addr_t for dma_desc_pool, and %pad to print dma_addr_t.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200818115101.55700-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This eliminates the following sparse warning:
drivers/dma/ioat/dma.c:29:5: warning: symbol 'completion_timeout' was
not declared. Should it be static?
drivers/dma/ioat/dma.c:33:5: warning: symbol 'idle_timeout' was not
declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20200912072158.602585-1-yanaijie@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'desc' variable is now defined but not used in sf_pdma_donebh_tasklet(),
causing this warning:
drivers/dma/sf-pdma/sf-pdma.c: In function 'sf_pdma_donebh_tasklet':
drivers/dma/sf-pdma/sf-pdma.c:287:23: warning: unused variable 'desc' [-Wunused-variable]
Remove this unused variable
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20200914055302.22962-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ context, disabling IRQ is redundant.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20200912094036.32112-1-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831134745.314945-1-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200831103542.305571-36-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-34-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-33-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-32-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200831103542.305571-31-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-30-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-29-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-28-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200831103542.305571-27-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-26-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-25-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-24-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-23-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-22-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-21-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-20-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-19-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-18-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-17-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-16-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-15-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-14-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-13-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-12-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-11-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20200831103542.305571-10-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-9-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-7-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-6-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-5-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-4-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-3-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200831103542.305571-2-allen.lkml@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'desc' variable is now defined but not used in sf_pdma_donebh_tasklet(),
causing this warning:
drivers/dma/sf-pdma/sf-pdma.c: In function 'sf_pdma_donebh_tasklet':
drivers/dma/sf-pdma/sf-pdma.c:287:23: warning: unused variable 'desc' [-Wunused-variable]
Remove this unused variable
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The original commit mixed up the forward and completion ring IDs for the
rx flow configuration.
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: 4927b1ab20 ("dmaengine: ti: k3-udma: Switch to k3_ringacc_request_rings_pair")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
rcar-dmac driver is used on Renesas R-Car Gen{2,3} and Renesas
RZ/G{1,2} SoC's, update the same to reflect the description
for RCAR_DMAC config.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Link: https://lore.kernel.org/r/20200911095734.19348-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use separate data for SoC dependent parameters. These parameters depends
on the DMA integration (either in HW or in SYSFW), the DMA controller
itself remains compatible with either the am654 or j721e variant.
j7200 have the same DMA as j721e with different number of channels, which
can be queried from HW, but SYSFW defines different rchan_oes_offset
number for j7200 (0x80) compared to j721e (0x400).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200910124329.21206-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When we got an error from DMA mapping API we convert a negative value
to unsigned long type and hence make user confused:
result #1: 'src mapping error' with src_off=0x19a72 dst_off=0xea len=0xccf4 (18446744073709551604)
Change this to print error codes as signed values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200907101306.61824-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Because a callback is called twice when DMA transfer complete
the second callback may be possible to access a freed memory
if the first callback routines perform the dma_release_channel function.
So this patch serialized the callback functions
Signed-off-by: Brad Kim <brad.kim@semifive.com>
Tested-and-reviewed-by: Green Wan <green.wan@sifive.com>
Signed-off-by: Brad Kim <brad.kim@sifive.com>
Link: https://lore.kernel.org/r/20200903111726.3413-1-brad.kim@sifive.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Core:
- drop ACPI CSRT table reference after using it
- fix of_dma_router_xlate() error handling
Drivers: Off fixes in:
- idxd
- at_hdmac
- pl330
- dw-edma
- jz478
-----BEGIN PGP SIGNATURE-----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=DUvT
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A couple of core fixes and odd driver fixes for dmaengine subsystem:
Core:
- drop ACPI CSRT table reference after using it
- fix of_dma_router_xlate() error handling
Drivers fixes in idxd, at_hdmac, pl330, dw-edma and jz478"
* tag 'dmaengine-fix-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: ti: k3-udma: Update rchan_oes_offset for am654 SYSFW ABI 3.0
drivers/dma/dma-jz4780: Fix race condition between probe and irq handler
dmaengine: dw-edma: Fix scatter-gather address calculation
dmaengine: ti: k3-udma: Fix the TR initialization for prep_slave_sg
dmaengine: pl330: Fix burst length if burst size is smaller than bus width
dmaengine: at_hdmac: add missing kfree() call in at_dma_xlate()
dmaengine: at_hdmac: add missing put_device() call in at_dma_xlate()
dmaengine: at_hdmac: check return value of of_find_device_by_node() in at_dma_xlate()
dmaengine: of-dma: Fix of_dma_router_xlate's of_dma_xlate handling
dmaengine: idxd: reset states after device disable or reset
dmaengine: acpi: Put the CSRT table after using it
SYSFW ABI 3.0 has changed the rchan_oes_offset value for am654 to support
SR2.
Since the kernel now needs SYSFW API 3.0 to work because the merged irqchip
update, we need to also update the am654 rchan_oes_offset.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200831091019.25273-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Export admin command status to sysfs attribute in order to allow user to
retrieve configuration error. Allows user tooling to retrieve the command
error and provide more user friendly error messages.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159865278770.29455.8026892329182750127.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add sysfs attribute max_batch_size to wq in order to allow the max batch
size configured on a per wq basis. Add support code to configure
the valid user input on wq enable. This is a performance tuning
parameter.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159865273617.29141.4383066301730821749.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add sysfs attribute max_xfer_size to wq in order to allow the max xfer
size configured on a per wq basis. Add support code to configure
the valid user input on wq enable. This is a performance tuning
parameter.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159865265404.29141.3049399618578194052.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828152637.16903-3-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828152637.16903-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828152637.16903-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Split IS_ERR_OR_NULL() check followed by additional conditional
to two simple conditionals. This increases readability and saves memory:
Function old new delta
dma_request_chan 700 697 -3
Total: Before=10224, After=10221, chg -0.03%
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200828144519.14483-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New drivers should use dma_request_chan() instead
dma_request_slave_channel()
dma_request_slave_channel() is a simple wrapper for dma_request_chan()
eating up the error code for channel request failure and makes deferred
probing impossible.
Move the dma_request_slave_channel() into the header as inline function,
mark it as deprecated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828110507.22407-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit ef91bb196b ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.
That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical. There were no
high bits to mask off to begin with.
But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.
Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all. Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.
This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.
This patch at least makes it not fail the build any more, and makes the
logic superficially sane. Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Starting with core version 4.3.a the DMA bus attributes can (and should) be
read from the INTERFACE_DESCRIPTION (0x10) register.
For older core versions, this will still need to be provided from the
device-tree.
The bus-type values are identical to the ones stored in the device-trees,
so we just need to read them. Bus-width values are stored in log2 values,
so we just need to use them as shift values to make them equivalent to the
current format.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-7-alexandru.ardelean@analog.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The channel parameters (which are read from the device-tree) are adjusted
for the DMAEngine framework in the axi_dmac_parse_chan_dt() function, after
they are read from the device-tree.
When we want to read these from registers, we will need to use the same
logic, so this change splits the logic into a separate function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-6-alexandru.ardelean@analog.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The clock may also be required to read registers from the IP core (if it is
provided and the driver needs to control it).
So, move it earlier in the probe.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-4-alexandru.ardelean@analog.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We want to enable the clock right after it is obtained. Then later we'll
want to read the core version via register-access (which requires the clock
to be enabled).
The initialization of the active_descs list can be postponed after reading
from registers (or reading the device-tree).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-3-alexandru.ardelean@analog.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 'version' of the IP core will be needed to adapt the driver to a new
feature (i.e. reading some DMA parameters from registers).
To do that, the version will be checked, so this is being moved out of the
axi_dmac_detect_caps() function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-2-alexandru.ardelean@analog.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In probe, IRQ is requested before zchan->id is initialized which can be
read in the irq handler. Hence, shift request irq after other initializations
complete.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200821034423.12713-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instruction dump uses two printk() in a row to print one instruction. Use
KERN_CONT to prevent breaking the output in the middle.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20200813204123.19044-1-l.stelmach@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the source and destination physical address calculation of a
peripheral device on scatter-gather implementation.
This issue manifested during tests using a 64 bits architecture system.
The abnormal behavior wasn't visible before due to all previous tests
were done using 32 bits architecture system, that masked his effect.
Fixes: e63d79d1ff ("dmaengine: Add Synopsys eDMA IP core driver")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/8d3ab7e2ba96563fe3495b32f60077fffb85307d.1597327623.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The direction has been already validated in the main callback and there is
no need to check it again in the TR mode handlers for slave_sg and cyclic.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200824120120.9270-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The TR which needs to be initialized for the next sg entry is indexed by
tr_idx and not by the running i counter.
In case any sub element in the SG needs more than one TR, the code would
corrupt an already configured TR.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200824120108.9178-1-peter.ujfalusi@ti.com
Fixes: 6cf668a4ef ("dmaengine: ti: k3-udma: Use the TR counter helper for slave_sg and cyclic")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the burst len fixup after setting the generic value for it. This
finally enables the fixup introduced by commit 137bd11090 ("dmaengine:
pl330: Align DMA memcpy operations to MFIFO width"), which otherwise was
overwritten by the generic value.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 137bd11090 ("dmaengine: pl330: Align DMA memcpy operations to MFIFO width")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200825064617.16193-1-m.szyprowski@samsung.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If memory allocation for 'atslave' succeed, at_dma_xlate() doesn't have a
corresponding kfree() in exception handling. Thus add kfree() for this
function implementation.
Fixes: bbe89c8e3d ("at_hdmac: move to generic DMA binding")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200817115728.1706719-4-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If of_find_device_by_node() succeed, at_dma_xlate() doesn't have a
corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: bbe89c8e3d ("at_hdmac: move to generic DMA binding")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200817115728.1706719-3-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The reurn value of of_find_device_by_node() is not checked, thus null
pointer dereference will be triggered if of_find_device_by_node()
failed.
Fixes: bbe89c8e3d ("at_hdmac: move to generic DMA binding")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200817115728.1706719-2-yukuai3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sparse tool complains as follows:
drivers/dma/xilinx/xilinx_dpdma.c:349:37: warning:
symbol 'dpdma_debugfs_reqs' was not declared. Should it be static?
This variable is not used outside of xilinx_dpdma.c, so this commit
marks it static.
Fixes: 1d220435ca ("dmaengine: xilinx: dpdma: Add debugfs support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200818112217.43816-1-weiyongjun1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.
For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to the DW DMA controller Databook 2.18b (page 40 "3.5 Memory
Peripherals") memory peripherals don't have handshaking interface
connected to the controller, therefore they can never be a flow
controller. Since the CTLx.SRC_MSIZE and CTLx.DEST_MSIZE are properties
valid only for peripherals with a handshaking interface, we can freely
zero these fields out if the memory peripheral is selected to be the
source or the destination of the DMA transfers.
Note according to the databook, length of burst transfers to memory is
always equal to the number of data items available in a channel FIFO or
data items required to complete the block transfer, whichever is smaller;
length of burst transfers from memory is always equal to the space
available in a channel FIFO or number of data items required to complete
the block transfer, whichever is smaller.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Indeed in case of the DMA_DEV_TO_MEM DMA transfers it's enough to take the
destination memory address and the destination master data width into
account to calculate the CTLx.DST_TR_WIDTH setting of the memory
peripheral. According to the DW DMAC IP-core Databook 2.18b (page 66,
Example 5) at the and of a DMA transfer when the DMA-channel internal FIFO
is left with data less than for a single destination burst transaction,
the destination peripheral will enter the Single Transaction Region where
the DW DMA controller can complete a block transfer to the destination
using single transactions (non-burst transaction of CTLx.DST_TR_WIDTH
bytes). If there is no enough data in the DMA-channel internal FIFO for
even a single non-burst transaction of CTLx.DST_TR_WIDTH bytes, then the
channel enters "FIFO flush mode". That mode is activated to empty the FIFO
and flush the leftovers out to the memory peripheral. The flushing
procedure is simple. The data is sent to the memory by means of a set of
single transaction of CTLx.SRC_TR_WIDTH bytes. To sum up it's redundant to
use the LLPs length to find out the CTLx.DST_TR_WIDTH parameter value,
since each DMA transfer will be completed with the CTLx.SRC_TR_WIDTH bytes
transaction if it is required.
We suggest to remove the LLP entry length from the statement which
calculates the memory peripheral DMA transaction width since it's
redundant due to the feature described above. By doing so we'll improve
the memory bus utilization and speed up the DMA-channel performance for
DMA_DEV_TO_MEM DMA-transfers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion.
In other words it determines when to start pushing data out of a DW
DMAC channel FIFO to a destination peripheral or from a source
peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one
for all DW DMAC channels. It means they are tuned to flush data out of
FIFO (to a memory peripheral or by accepting the burst transaction
requests) when FIFO is at least half-full (except at the end of the block
transfer, when FIFO-flush mode is activated) and are configured to get
data to the FIFO when it's at least half-empty.
Such configuration is a good choice when there is no slave device involved
in the DMA transfers. In that case the number of bursts per block is less
than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve.
But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1,
since DW DMAC will wait for the channel FIFO contents to be either
half-full or half-empty depending on having the destination or the source
transfers. Such latencies might be dangerous in case if the DMA transfers
are expected to be performed from/to a slave device. Since normally
peripheral devices keep data in internal FIFOs, any latency at some
critical moment may cause one being overflown and consequently losing
data. This especially concerns a case when either a peripheral device is
relatively fast or the DW DMAC engine is relatively slow with respect to
the incoming data pace.
In order to solve problems, which might be caused by the latencies
described above, let's enable the FIFO half-full/half-empty "FIFO
readiness" criterion only for DMA transfers with no slave device involved.
Thanks to the commit 99ba8b9b0d ("dmaengine: dw: Initialize channel
before each transfer") we can freely do that in the generic
dw_dma_initialize_chan() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Jonathan McDowell