The node names should be generic and DT schema expects certain pattern:
qcom/msm8998-oneplus-cheeseburger.dtb: leds: 'button-backlight' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
qcom/sc7180-trogdor-coachz-r1.dtb: pwmleds: 'keyboard-backlight' does not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221125144209.477328-1-krzysztof.kozlowski@linaro.org
Introduce the Qualcomm SA8540P ride automotive platform, also known as
Qdrive-3 development board.
This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs and USB.
The SA8540P ride contains four PM8450 PMICs. A separate DTSI file has
been created for PMIC, so that it can be used for future SA8540P based
boards.
Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Tested-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221118025158.16902-3-quic_ppareek@quicinc.com
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX223&224 DTSIs to better document the hardware.
Diff between 223 and 224:
< gpio-line-names = "NC", /* GPIO_0 */
< "NC",
< "NC",
< "NC",
> gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
> "TELE_SPI_MOSI",
> "TELE_SPI_CLK",
> "TELE_SPI_CS_N",
< "PM8010_2_RESET_N",
> "NC",
< "NC",
> "UWIDEC_PWR_EN",
< "TOF_RST_N",
> "NC"
< "QLINK1_REQ",
< "QLINK1_EN", /* GPIO_160 */
< "QLINK1_WMSS_RESET_N",
> "NC",
> "NC", /* GPIO_160 */
> "NC",
The tele lens setup is different on 1 IV and 5 IV and power wiring
is different for some lenses, so it makes sense. As for QLINK, no
idea.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117141613.19942-1-konrad.dybcio@linaro.org
This is a device property, not a bus host one.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117105845.13644-1-konrad.dybcio@linaro.org
Qualcomm platforms making use of CPUFreq HW Engine (EPSS/OSM) supply clocks
to the CPU cores. But this relationship is not represented in DTS so far.
So let's make cpufreq node as the clock provider and CPU nodes as the
consumers. The clock index for each CPU node is based on the frequency
domain index.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117053145.10409-3-manivannan.sadhasivam@linaro.org
The Vision Mezzanine for the RB5 ships with an imx577 and ov9282 populated.
Other sensors and components may be added or stacked with additional
mezzanines.
Enable the IMX577 on the vision mezzanine.
An example media-ctl pipeline for the imx577 is:
media-ctl --reset
media-ctl -v -d /dev/media0 -V '"imx577 '22-001a'":0[fmt:SRGGB10/4056x3040 field:none]'
media-ctl -V '"msm_csiphy2":0[fmt:SRGGB10/4056x3040]'
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4056x3040]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4056x3040]'
media-ctl -l '"msm_csiphy2":1->"msm_csid0":0[1]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 4056x3040 -F /dev/video0
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-8-bryan.odonoghue@linaro.org
Define the set of possible ports, one for each CSI PHY along with the port
address and size cells @ the SoC dtsi level.
Suggested-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-7-bryan.odonoghue@linaro.org
Move the dts data for the rb3 navigation mezzanine into its own dts file.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-6-bryan.odonoghue@linaro.org
Use preferred "ok" not "okay".
Use preferred status "disabled" instead of "disable".
There's no functional change here so no Fixes has been applied.
Reported-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-5-bryan.odonoghue@linaro.org
The reg for the port is specified in the dtsi. Remove from the db845c dts.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-4-bryan.odonoghue@linaro.org
sdm845.dtsi camss already defines the address-cells and size-cells for
camss, no need to replicate in sdm845-db845c.dts.
Reported-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-3-bryan.odonoghue@linaro.org
The number of available ports is SoC specific so we should define it in the
SoC dtsi. For the case of the sdm845 that is 4 CSI PHYs => four ports.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221117003232.589734-2-bryan.odonoghue@linaro.org
Adjust regulators, add required pin setup and finally enable SDHCI2
to get the SD Card slot going on Sagami Xperias.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116123612.34302-4-konrad.dybcio@linaro.org
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the Sagami-common / PDX215 DTSIs to better document the
hardware.
Diff between 215 and common:
< "NC",
< "NC",
> "WLC_I2C_SDA",
> "WLC_I2C_SCL",
< "NC",
> "WLC_INT_N",
> "CAM_MCLK4",
< "NC",
< "NC",
> "TOF_RST_N",
< "NC",
< "NC",
< "NC",
> "QLINK1_REQ",
> "QLINK1_EN",
> "QLINK1_WMSS_RESET_N",
It's pretty logical as 1 III has WLC (WireLess Charging), and an
additional 3D iToF sensor. As for QLINK, no idea.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116123612.34302-3-konrad.dybcio@linaro.org
Add and configure the SDHCI host responsible for (mostly) SD Card and
its corresponding pins' sleep states.
The setup is *literally* 1:1 with 8450 (bar SDR50/104 may not be
broken).
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116123612.34302-2-konrad.dybcio@linaro.org
When recently adding the missing 'regulator-allowed-modes' properties it
appears that the binding example with its four-spaces indentation
(corresponding to a single tab, which is still to little) was copied
verbatim.
Drop the unnecessary first line break after 'regulator-allowed-modes'
properties and indent the single remaining continuation line properly.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116102054.4673-3-johan+linaro@kernel.org
Remove unused and redundant sleep pin control entries as they are
not referenced anywhere in sc7280 based platform's device tree variants.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reported-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1668591184-21099-1-git-send-email-quic_srivasam@quicinc.com
PMK8350 is the first PMIC to require both HLOS and PBS registers for
PON to function properly (at least in theory, sm8350 sees no change).
The support for it on the driver side has been added long ago,
but it has never been wired up. Do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115132626.7465-1-konrad.dybcio@linaro.org
Use the defines from qcom-rpmpd.h instead of bare numbers for
readability.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115130936.6830-2-konrad.dybcio@linaro.org
Use the defines from qcom-rpmpd.h instead of bare numbers for
readability.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115130936.6830-1-konrad.dybcio@linaro.org
Set SDHCI VMMC/VQMMC to <=2v96 and allow load setting by the SDHCI
driver, as required by this use case.
Configure the SD Card Detect pin, enable the SDHCI2 controller and
assign it the aforementioned regulators.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221114105043.36698-4-konrad.dybcio@linaro.org
Add a pretty bog-standard-for-Xperias-for-the-past-3-years
touchscreen setup.
The OEM that built the Xperia 10 IV for SONY decided to use some
kind of a GPIO regulator that needs to be enabled at all times
for both the touch panel and the display panel to function.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115152727.9736-10-konrad.dybcio@linaro.org
Configure the second SDHCI bus controller, which usually the
interface used for SD cards.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221114105043.36698-3-konrad.dybcio@linaro.org
Add necessary nodes to support various QUP configurations. Note that:
- QUP3/4/5 and 11 are straight up missing
- There may be more QUPs physically on the SoC that work perfectly
fine, but Qualcomm decided not to expose them on the downstream kernel
- Many are missing pinctrls, as there are both missing pin funcs in
the TLMM driver and missing configuration settings (though they are
possible to guesstimate quite easily)
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115152727.9736-6-konrad.dybcio@linaro.org
Add the pin setup for SPI/I2C configurations that are supported
downstream. I can guesstimate the correct settings for other buses,
but:
- I have no hardware to test it on
- Some QUPs are straight up missing pin funcs in TLMM
- Vendors probably didn't really care and used whatever was there in
the reference design and BSP - should any other be used, they can be
configured at a later time
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115152727.9736-5-konrad.dybcio@linaro.org
PMK8350 is shipped on SID6 with some SoCs, for example with SM6375.
Add some preprocessor logic to allow changing the SID in cases like
this.
While I am not in favour of adding #if's into the device tree, this
is the least messy way to handle this. If one isn't specified, it
will default to 0 (as it has been previously).
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115152727.9736-3-konrad.dybcio@linaro.org
Add device node and required pinctrl settings (as well as a fixup for
an existing one, whoops!) to support the Samsung Electronics
touchscreen on Nagara devices.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221114095654.34561-4-konrad.dybcio@linaro.org
Add a device tree for the Xperia 5 IV (pdx224). It's literally the 1 IV
with a smaller body, different panel, one camera lens (not sensor afaict)
swapped out and no 3D iToF sensor, hence the device-specific DT is tiny.
Be sure to follow the vbmeta disablement steps (detailed in pdx223
introduction commit message), otherwise your phone will not boot and
will reject anything and everything with just a non-descriptive
"Your device is corrupted" followed by a sad reboot. This should not
be the case, as vbmeta should be plainly ignored in unlocked state,
but what can we do..
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221114095654.34561-3-konrad.dybcio@linaro.org
New device support - Xiaomi Mi6 phone
What works:
- storage
- usb
- power regulators
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konra.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221112203300.536010-3-dsankouski@gmail.com
This adds support for the Sony Xperia Loire/SmartLoire platform
with a base configuration that is common across all of the
devices that are based on this project.
Also adds a base DT configuration for the Xperia X and Xperia
X Compact (respectively, Suzu and Kugo) which is valid for both
their RoW (single-sim), DSDS (dual-sim) and other regional
variants of these two smartphones, that makes us able to boot
to a UART console.
Please note that, currently, the APC0/1 (cluster 0/1) vregs
are set to a safe voltage in order to ensure boot stability
until a proper solution for CPU DVFS scaling lands.
Co-developed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Co-developed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111120156.48040-12-angelogioacchino.delregno@collabora.com
This commit adds device trees for MSM8956 and MSM8976 SoCs.
They are *almost* identical, with minor differences, such as
MSM8956 having two A72 cores less.
However, there is a bug in Sony Loire bootloader that requires presence
of all 8 cores in the cpu{} node, so these will not be deleted.
Co-developed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Co-developed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111120156.48040-11-angelogioacchino.delregno@collabora.com
The PM8950 features integrated peripherals like ADC, GPIO controller,
MPPs, PON keys and others.
Add them to DT files that will be imported on boards having this PMIC
combo (or one of them, anyways).
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Co-developed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111120156.48040-10-angelogioacchino.delregno@collabora.com
When adding support for the DisplayPort part of the QMP PHY the binding
(and devicetree parser) for the (USB) child node was simply reused and
this has lead to some confusion.
The third DP register region is really the DP_PHY region, not "PCS" as
the binding claims, and lie at offset 0x2a00 (not 0x2c00).
Similarly, there likely are no "RX", "RX2" or "PCS_MISC" regions as
there are for the USB part of the PHY (and in any case the Linux driver
does not use them).
Note that the sixth "PCS_MISC" region is not even in the binding.
Fixes: 5aa0d1becd ("arm64: dts: qcom: sm8250: switch usb1 qmp phy to USB3+DP mode")
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111094729.11842-3-johan+linaro@kernel.org
When adding support for the DisplayPort part of the QMP PHY the binding
(and devicetree parser) for the (USB) child node was simply reused and
this has lead to some confusion.
The third DP register region is really the DP_PHY region, not "PCS" as
the binding claims, and lie at offset 0x2a00 (not 0x2c00).
Similarly, there likely are no "RX", "RX2" or "PCS_MISC" regions as
there are for the USB part of the PHY (and in any case the Linux driver
does not use them).
Note that the sixth "PCS_MISC" region is not even in the binding.
Fixes: 23737b9557 ("arm64: dts: qcom: sm6350: Add USB1 nodes")
Cc: stable@vger.kernel.org # 5.16
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111094729.11842-2-johan+linaro@kernel.org
The source clock for the reference clock should not be described by the
devicetree binding and instead this relationship should be modelled in
the clock driver.
Update the USB PHY nodes to match the fixed binding.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111093857.11360-4-johan+linaro@kernel.org
Add the two bwmon instances and define votes for CPU -> LLCC and LLCC ->
DDR, with bandwidth values based on the downstream DeviceTree.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111032515.3460-11-quic_bjorande@quicinc.com
Add the L3 interconnect path to all CPUs and define the bandwidth
requirements for all opp entries across sc8280xp and sa8540p.
The values are based on the tables reported by the hardware, distributed
such that each value is the largest value, lower than the cluster
frequency.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111032515.3460-9-quic_bjorande@quicinc.com
Update all references to OSM or EPSS L3 compatibles, to include the
generic compatible, as defined by the updated binding.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221111032515.3460-7-quic_bjorande@quicinc.com
Lin, Meng-Bo