Update dt-binding documentation to add support for setting byteswap of
chrontel ch7033.
New property name of chrontel,byteswap added to set the byteswap order.
This property is optional.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902153906.31000-2-macroalpha82@gmail.com
Implement the bridge connector-related .get_edid() and .detect()
operations for full DP mode, and report the related bridge capabilities
and type.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-4-tomi.valkeinen@ideasonboard.com
Despite the SN65DSI86 being an eDP bridge, on some systems its output is
routed to a DisplayPort connector. Enable DisplayPort mode when the next
component in the display pipeline is detected as a DisplayPort
connector, and disable eDP features in that case.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reworked to set bridge type based on the next bridge/connector.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
--
Changes since v1/RFC:
- Rebased on top of "drm/bridge: ti-sn65dsi86: switch to
devm_drm_of_get_bridge"
- eDP/DP mode determined from the next bridge connector type.
Changes since v2:
- Remove setting of Standard DP Scrambler Seed. (It's read-only).
- Prevent setting DP_EDP_CONFIGURATION_SET in
ti_sn_bridge_atomic_enable()
- Use Doug's suggested text for disabling ASSR on DP mode.
Changes since v3:
- Remove ASSR_CONTROL definition
Changes since v4:
- Refactor code to configure the DP/eDP scrambler in one place.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-3-tomi.valkeinen@ideasonboard.com
The front and back porch registers are 8 bits, and pulse width registers
are 15 bits, so reject any modes with larger periods.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-2-tomi.valkeinen@ideasonboard.com
Expecting to observe a specific value, when the function responsible for
setting the value has failed will lead to extra noise in test output.
Use assert when the situation calls for it.
Also - very small tidying up around the changed areas (whitespace).
v2: Leave out the locals (drm_connector is huge) (lkp)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817211236.252091-2-michal.winiarski@intel.com
Negative tests can be expressed as a single parameterized test case,
which highlights that we're following the same test logic (passing
invalid cmdline and expecting drm_mode_parse_command_line_for_connector
to fail), which improves readability.
v2: s/negative/invalid to be consistent with other testcases in DRM
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817211236.252091-1-michal.winiarski@intel.com
Like commit c4f135d643 ("workqueue: Wrap flush_workqueue() using a
macro") says, flush_scheduled_work() is dangerous and will be forbidden.
We are on the way for removing all flush_scheduled_work() callers from
the kernel, and this patch is for removing flush_scheduled_work() call
from cadence driver.
Since cdns-mhdp8546 driver uses 4 works
mhdp->modeset_retry_work
mhdp->hpd_work
mhdp->hdcp.check_work
mhdp->hdcp.prop_work
I assume that flush_scheduled_work() in cdns_mhdp_remove() needs to wait
for only these 4 works.
Since mhdp->modeset_retry_work already uses cancel_work_sync(), I assume
that flush_scheduled_work() needs to wait for only 3 works. But I came to
wonder whether mhdp->hdcp.check_work should be flushed or cancelled.
While flush_scheduled_work() waits for completion of works which were
already queued to system_wq, mhdp->hdcp.check_work is a delayed work.
That is, this work won't be queued to system_wq unless timeout expires.
Current code will wait for mhdp->hdcp.check_work only if timeout already
expired. If timeout is not expired yet, flush_scheduled_work() will fail
to cancel mhdp->hdcp.check_work, and cdns_mhdp_hdcp_check_work() which is
triggered by mhdp->hdcp.check_work will schedule hdcp->check_work, which
is too late for flush_scheduled_work() to wait for completion of
cdns_mhdp_hdcp_prop_work().
But since I couldn't get comments on how do we want to handle this race
window [1], this patch chose "do nothing" for mhdp->hdcp.check_work and
mhdp->hdcp.prop_work. That is, I assume that flush_scheduled_work() in
cdns_mhdp_remove() needs to wait for only mhdp->hpd_work work.
Link: https://lkml.kernel.org/r/943273cb-c2ec-24e3-5edb-64eacc6e2d30@I-love.SAKURA.ne.jp [1]
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/216591bc-28bb-0453-10bb-59e268dff540@I-love.SAKURA.ne.jp
Convert to io-pgtable's bulk {map,unmap}_pages() APIs, to help the old
single-page interfaces eventually go away. Unmapping heap BOs still
wants to be done a page at a time, but everything else can get the full
benefit of the more efficient interface.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Alyssa Rosenzweig <alyssa@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/daef7f8c134d989c55636a5790d8c0fcaca1bae3.1661205687.git.robin.murphy@arm.com
panel-edp changes go through the drm-misc tree (as per the "DRM PANEL
DRIVERS" entry in MAINTAINERS), but ever since splitting panel-edp out
of panel-simple I've been trying to keep a close eye on it. Make that
official by listing me as a reviewer.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220822105340.1.I66a9a5577f9b0af66492ef13c47bc78ed85e5d6b@changeid
Send DP_SET_POWER_D3 command to the downstream before stopping DP, so the
suspend process will not be interrupted by the HPD interrupt. Also modify
the order in .atomic_enable callback to make the callbacks symmetric.
Fixes: 46ca7da7f1 ("drm/bridge: it6505: Send DPCD SET_POWER to downstream")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220830045756.1655954-1-treapking@chromium.org
When removing the module we will get the following warning:
[ 31.911505] i2c-core: driver [stdp2690-ge-b850v3-fw] unregistered
[ 31.912484] general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN PTI
[ 31.913338] KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
[ 31.915280] RIP: 0010:drm_bridge_remove+0x97/0x130
[ 31.921825] Call Trace:
[ 31.922533] stdp4028_ge_b850v3_fw_remove+0x34/0x60 [megachips_stdpxxxx_ge_b850v3_fw]
[ 31.923139] i2c_device_remove+0x181/0x1f0
The two bridges (stdp2690, stdp4028) do not probe at the same time, so
the driver does not call ge_b850v3_resgiter() when probing, causing the
driver to try to remove the object that has not been initialized.
Fix this by checking whether both the bridges are probed.
Fixes: 11632d4aa2 ("drm/bridge: megachips: Ensure both bridges are probed before registration")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220830073450.1897020-1-zheyuma97@gmail.com
Add a helper for getting the DP PHY name. In the interest of caller
simplicity and to avoid allocations and passing in of buffers, duplicate
the const strings to return. It's a minor penalty to pay for simplicity
in all the call sites.
v2: Rebase, add kernel-doc, ensure non-NULL always
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b08dc12a7e621a48ec35546d6cd1ed4b1434810d.1660553850.git.jani.nikula@intel.com
The double reset power-on sequence is a workaround for the hardware
flaw in some chip that SPI Clock output glitch and cause internal MPU
unable to read firmware correctly. The sequence is suggested in ps8640
application note.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Rock Chiu <rock.chiu@paradetech.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220815093905.134164-1-hsinyi@chromium.org
There are two events that signal a real change of the link state: HPD going
high means the sink is newly connected or wants the source to re-read the
EDID, RX sense going low is a indication that the link has been disconnected.
Ignore the other two events that also trigger interrupts, but don't need
immediate attention: HPD going low does not necessarily mean the link has
been lost and should not trigger a immediate read of the status. RX sense
going high also does not require a detect cycle, as HPD going high is the
right point in time to read the EDID.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> (v1)
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220826185733.3213248-1-l.stach@pengutronix.de
The drm_of_lvds_get_data_mapping() returns either negative value on
error or MEDIA_BUS_FMT_* otherwise. The check for 'ret' would also
catch the positive case of MEDIA_BUS_FMT_* and lead to probe failure
every time 'data-mapping' DT property is specified.
Fixes: 7c4dd0a266 ("drm: of: Add drm_of_lvds_get_data_mapping")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801125419.167562-1-marex@denx.de
Currently the driver only handles panel directly connected to the DPI output.
Handle the case where a bridge is connected past DPI output of this bridge.
This could be e.g. DPI to LVDS encoder chip.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220724224317.288727-1-marex@denx.de
1. Support HDMI_I2S audio format.
2. Return 0 if there is no sink connection in .hw_param callback.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Acked-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Jiaxin Yu<jiaxin.yu@mediatek.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220726033058.403715-1-xji@analogixsemi.com
At some point the DRM printers started adding a newline after each
print. This caused SDVO command debug printing to look weird. Fix this
by using snprintf to print into a buffer which can be printed as a whole
by DRM_DEBUG_KMS(). Code is heavily inspired by i915.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220610130925.8650-1-patrik.r.jakobsson@gmail.com
The "ret" variable is ambiguously returning something that
could be zero in the tve200_modeset_init() function, assign
it an explicit error return code to make this unambiguous.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220505215019.2332613-1-linus.walleij@linaro.org
The ICN6211 is capable of deriving its internal PLL clock from either
MIPI DSI HS clock, external REFCLK clock, or even internal oscillator.
Currently supported is only the first option. Add support for external
REFCLK clock input in addition to that.
There is little difference between these options, except that in case
of MIPI DSI HS clock input, the HS clock are pre-divided by a fixed /4
divider before being fed to the PLL input, while in case of external
REFCLK, the RECLK clock are fed directly into the PLL input.
Per exceptionally poor documentation, the REFCLK must be in range of
10..154 MHz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801131747.183041-2-marex@denx.de
The ICN6211 is capable of deriving its internal PLL clock from either
MIPI DSI HS clock, external REFCLK clock, or even internal oscillator.
Currently supported is only the first option. Document support for
external REFCLK clock input in addition to that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801131747.183041-1-marex@denx.de
Fill in hs_rate and lp_rate to struct mipi_dsi_device for this bridge and
adjust DSI input frequency calculations such that they expect the DSI host
to configure HS clock according to hs_rate.
This is an optimization for the DSI burst mode case. In case the DSI device
supports DSI burst mode, it is recommended to operate the DSI interface at
the highest possible HS clock frequency which the DSI device supports. This
permits the DSI host to send as short as possible bursts of data on the DSI
link and keep the DSI data lanes in LP mode otherwise, which reduces power
consumption.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801131555.182969-1-marex@denx.de
drm_mipi_dbi needs lots of DRM_KMS_HELPER support, so select
that Kconfig symbol like it is done is most other uses, and
the way that it was before MIPS_DBI was moved from tinydrm
to its core location.
Fixes these build errors:
ld: drivers/gpu/drm/drm_mipi_dbi.o: in function `mipi_dbi_buf_copy':
drivers/gpu/drm/drm_mipi_dbi.c:205: undefined reference to `drm_gem_fb_get_obj'
ld: drivers/gpu/drm/drm_mipi_dbi.c:211: undefined reference to `drm_gem_fb_begin_cpu_access'
ld: drivers/gpu/drm/drm_mipi_dbi.c:215: undefined reference to `drm_gem_fb_vmap'
ld: drivers/gpu/drm/drm_mipi_dbi.c:222: undefined reference to `drm_fb_swab'
ld: drivers/gpu/drm/drm_mipi_dbi.c:224: undefined reference to `drm_fb_memcpy'
ld: drivers/gpu/drm/drm_mipi_dbi.c:227: undefined reference to `drm_fb_xrgb8888_to_rgb565'
ld: drivers/gpu/drm/drm_mipi_dbi.c:235: undefined reference to `drm_gem_fb_vunmap'
ld: drivers/gpu/drm/drm_mipi_dbi.c:237: undefined reference to `drm_gem_fb_end_cpu_access'
ld: drivers/gpu/drm/drm_mipi_dbi.o: in function `mipi_dbi_dev_init_with_formats':
ld: drivers/gpu/drm/drm_mipi_dbi.o:/X64/../drivers/gpu/drm/drm_mipi_dbi.c:469: undefined reference to `drm_gem_fb_create_with_dirty'
Fixes: 174102f4de ("drm/tinydrm: Move mipi-dbi")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Dillon Min <dillon.minfei@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220823004243.11596-1-rdunlap@infradead.org
Use 'select' instead of 'depends on' for DRM helpers for the
Ilitek ILI9341 panel driver.
This is what is done in the vast majority of other cases and
this makes it possible to fix a build error with drm_mipi_dbi.
Fixes: 5a04227326 ("drm/panel: Add ilitek ili9341 panel driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Dillon Min <dillon.minfei@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220823004227.10820-1-rdunlap@infradead.org
When VIRTGPU_EXECBUF_RING_IDX is used, we should be considering the
timeline that the EB if running on rather than the global driver fence
context.
Fixes: 85c83ea915 ("drm/virtio: implement context init: allocate an array of fence contexts")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20220812224001.2806463-1-robdclark@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In vc4_hvs_dump_state() potentially freed resources are protected from
being accessed with drm_dev_enter()/drm_dev_exit().
Also include drm_print_regset32() in the protected section, since
drm_print_regset32() does access memory that is typically mapped via
devm_* calls.
Fixes: 969cfae1f0 ("drm/vc4: hvs: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-5-dakr@redhat.com
(Hardware) resources which are bound to the driver and device lifecycle
must not be accessed after the device and driver are unbound.
However, the DRM device isn't freed as long as the last user closed it,
hence userspace can still call into the driver.
Therefore protect the critical sections which are accessing those
resources with drm_dev_enter() and drm_dev_exit().
Fixes: 7cc4214c27 ("drm/vc4: crtc: Switch to drmm_kzalloc")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-4-dakr@redhat.com
(Hardware) resources which are bound to the driver and device lifecycle
must not be accessed after the device and driver are unbound.
However, the DRM device isn't freed as long as the last user closed it,
hence userspace can still call into the driver.
Therefore protect the critical sections which are accessing those
resources with drm_dev_enter() and drm_dev_exit().
Fixes: 9872c7a319 ("drm/vc4: plane: Switch to drmm_universal_plane_alloc()")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-3-dakr@redhat.com
In vc4_hdmi_encoder_{pre,post}_crtc_enable() commit cd00ed5187
("drm/vc4: hdmi: Protect device resources after removal") missed to
unlock the mutex before returning due to drm_dev_enter() indicating the
device being unplugged.
Fixes: cd00ed5187 ("drm/vc4: hdmi: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-2-dakr@redhat.com
Now that we've finally gotten rid of the non-atomic MST users leftover in
the kernel, we can finally get rid of all of the legacy payload code we
have and move as much as possible into the MST atomic state structs. The
main purpose of this is to make the MST code a lot less confusing to work
on, as there's a lot of duplicated logic that doesn't really need to be
here. As well, this should make introducing features like fallback link
retraining and DSC support far easier.
Since the old payload code was pretty gnarly and there's a Lot of changes
here, I expect this might be a bit difficult to review. So to make things
as easy as possible for reviewers, I'll sum up how both the old and new
code worked here (it took me a while to figure this out too!).
The old MST code basically worked by maintaining two different payload
tables - proposed_vcpis, and payloads. proposed_vcpis would hold the
modified payload we wanted to push to the topology, while payloads held the
payload table that was currently programmed in hardware. Modifications to
proposed_vcpis would be handled through drm_dp_allocate_vcpi(),
drm_dp_mst_deallocate_vcpi(), and drm_dp_mst_reset_vcpi_slots(). Then, they
would be pushed via drm_dp_mst_update_payload_step1() and
drm_dp_mst_update_payload_step2().
Furthermore, it's important to note how adding and removing VC payloads
actually worked with drm_dp_mst_update_payload_step1(). When a VC payload
is removed from the VC table, all VC payloads which come after the removed
VC payload's slots must have their time slots shifted towards the start of
the table. The old code handles this by looping through the entire payload
table and recomputing the start slot for every payload in the topology from
scratch. While very much overkill, this ends up doing the right thing
because we always order the VCPIs for payloads from first to last starting
timeslot.
It's important to also note that drm_dp_mst_update_payload_step2() isn't
actually limited to updating a single payload - the driver can use it to
queue up multiple payload changes so that as many of them can be sent as
possible before waiting for the ACT. This is -technically- not against
spec, but as Wayne Lin has pointed out it's not consistently implemented
correctly in hubs - so it might as well be.
drm_dp_mst_update_payload_step2() is pretty self explanatory and basically
the same between the old and new code, save for the fact we don't have a
second step for deleting payloads anymore -and thus rename it to
drm_dp_mst_add_payload_step2().
The new payload code stores all of the current payload info within the MST
atomic state and computes as much of the state as possible ahead of time.
This has the one exception of the starting timeslots for payloads, which
can't be determined at atomic check time since the starting time slots will
vary depending on what order CRTCs are enabled in the atomic state - which
varies from driver to driver. These are still stored in the atomic MST
state, but are only copied from the old MST state during atomic commit
time. Likewise, this is when new start slots are determined.
Adding/removing payloads now works much more closely to how things are
described in the spec. When we delete a payload, we loop through the
current list of payloads and update the start slots for any payloads whose
time slots came after the payload we just deleted. Determining the starting
time slots for new payloads being added is done by simply keeping track of
where the end of the VC table is in
drm_dp_mst_topology_mgr->next_start_slot. Additionally, it's worth noting
that we no longer have a single update_payload() function. Instead, we now
have drm_dp_mst_add_payload_step1|2() and drm_dp_mst_remove_payload(). As
such, it's now left it up to the driver to figure out when to add or remove
payloads. The driver already knows when it's disabling/enabling CRTCs, so
it also already knows when payloads should be added or removed.
Changes since v1:
* Refactor around all of the completely dead code changes that are
happening in amdgpu for some reason when they really shouldn't even be
there in the first place… :\
* Remove mention of sending one ACT per series of payload updates. As Wayne
Lin pointed out, there are apparently hubs on the market that don't work
correctly with this scheme and require a separate ACT per payload update.
* Fix accidental drop of mst_mgr.lock - Wayne Lin
* Remove mentions of allowing multiple ACT updates per payload change,
mention that this is a result of vendors not consistently supporting this
part of the spec and requiring a unique ACT for each payload change.
* Get rid of reference to drm_dp_mst_port in DC - turns out I just got
myself confused by DC and we don't actually need this.
Changes since v2:
* Get rid of fix for not sending payload deallocations if ddps=0 and just
go back to wayne's fix
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-18-lyude@redhat.com
Right now, radeon is technically the only non-atomic driver still making
use of the MST helpers - and thus the final user of all of the legacy MST
helpers. Originally I was going to look into seeing if we could move legacy
MST into the radeon driver itself, however:
* SI and CIK both can use amdgpu, which still supports MST
* It currently doesn't work according to my own testing. I'm sure with some
troubleshooting we could likely fix it, but that brings me to point #2:
* It was never actually enabled by default, and is still marked as
experimental in the module parameter description
* If people were using it, someone probably would have probably seen a bug
report about how it is currently not functional by now. That certainly
doesn't appear to be the case, since before getting access to my own
hardware I had to go out of my way to try finding someone to help test
whether this legacy MST code even works - even amongst AMD employees.
* Getting rid of this code and only having atomic versions of the MST
helpers to maintain is likely going to be a lot easier in the long run,
and will make it a lot easier for others contributing to this code to
follow along with what's happening.
FWIW - if anyone still wants this code to be in the tree and has a good
idea of how to support this without needing to maintain the legacy MST
helpers (trying to move them would probably be acceptable), I'm happy to
suggestions. But my hope is that we can just drop this code and forget
about it. I've already run this idea by Harry Wentland and Alex Deucher a
few times as well.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-17-lyude@redhat.com
Currently, we set drm_dp_atomic_payload->time_slots to 0 in order to
indicate that we're about to delete a payload in the current atomic state.
Since we're going to be dropping all of the legacy code for handling the
payload table however, we need to be able to ensure that we still keep
track of the current time slot allocations for each payload so we can reuse
this info when asking the root MST hub to delete payloads. We'll also be
using it to recalculate the start slots of each VC.
So, let's keep track of the intent of a payload in drm_dp_atomic_payload by
adding ->delete, which we set whenever we're planning on deleting a payload
during the current atomic commit.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-16-lyude@redhat.com
We want to start cutting down on all of the places that we use port
validation, so that ports may be removed from the topology as quickly as
possible to minimize the number of errors we run into as a result of being
out of sync with the current topology status. This isn't a very typical
scenario and I don't think I've ever even run into it - but since the next
commit is going to make some changes to payload updates depending on their
hotplug status I think it's a probably good idea to take precautions.
Let's do this with CSNs by moving some code around so that we only queue
link address probing work at the end of handling all CSNs - allowing us to
make sure we drop as many topology references as we can beforehand.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-15-lyude@redhat.com
There's another kind of situation where we could potentially race with
nonblocking modesets and MST, especially if we were to only use the locking
provided by atomic modesetting:
* Display 1 begins as enabled on DP-1 in SST mode
* Display 1 switches to MST mode, exposes one sink in MST mode
* Userspace does non-blocking modeset to disable the SST display
* Userspace does non-blocking modeset to enable the MST display with a
different CRTC, but the SST display hasn't been fully taken down yet
* Execution order between the last two commits isn't guaranteed since they
share no drm resources
We can fix this however, by ensuring that we always pull in the atomic
topology state whenever a connector capable of driving an MST display
performs its atomic check - and then tracking CRTC commits happening on the
SST connector in the MST topology state. So, let's add some simple helpers
for doing that and hook them up in various drivers.
v2:
* Use intel_dp_mst_source_support() to check for MST support in i915, fixes
CI failures
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-14-lyude@redhat.com
Since we're going to be relying on atomic locking for payloads now (and the
MST mgr needs to track CRTCs), pull in the topology state for all modesets
in nv50_msto_atomic_check().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-13-lyude@redhat.com
Post-NV50, the only kind of encoder you'll find for DP connectors on Nvidia
GPUs are SORs (serial output resources). Because SORs have fixed
associations with their connectors, we can correctly assume that any DP
connector on a nvidia GPU will have exactly one SOR encoder routed to it
for DisplayPort.
Since we're going to need to be able to retrieve this fixed SOR DP encoder
much more often as a result of hooking up MST helpers for tracking
SST<->MST transitions in atomic states, let's simply cache this encoder in
nouveau_connector for any DP connectors on the system to avoid looking it
up each time. This isn't safe for NV50 since PIORs then come into play,
however there's no code pre-NV50 that would need to look this up anyhow -
so it's not really an issue.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-12-lyude@redhat.com
Currently with the MST helpers we avoid releasing payloads _and_ avoid
pulling in the MST state if there aren't any actual payload changes. While
we want to keep the first step, we need to now make sure that we're always
pulling in the MST state on all modesets that can modify payloads - even if
the resulting payloads in the atomic state are identical to the previous
ones.
This is mainly to make it so that if a CRTC is still assigned to a
connector but is set to DPMS off, the CRTC still holds it's payload
allocation in the atomic state and still appropriately pulls in the MST
state for commit tracking. Otherwise, we'll occasionally forget to update
MST payloads from changes caused by non-atomic DPMS changes. Doing this
also allows us to track bandwidth limitations in a state correctly even
between DPMS changes, so that there's no chance of a simple ->active change
being rejected by the atomic check.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-11-lyude@redhat.com
I'm not sure why, but at the time I originally wrote the find/release time
slot helpers I thought we should avoid keeping modeset tracking out of the
MST helpers. In retrospect though there's no actual good reason to do
this, and the logic has ended up being identical across all the drivers
using the helpers. Also, it needs to be fixed anyway so we don't break
things when going atomic-only with MST.
So, let's just move this code into drm_dp_atomic_release_time_slots() and
stop open coding it.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-10-lyude@redhat.com
As Daniel Vetter pointed out, if we only use the atomic modesetting locks
with MST it's technically possible for a driver with non-blocking modesets
to race when it comes to MST displays - as we make the mistake of not doing
our own CRTC commit tracking in the topology_state object.
This could potentially cause problems if something like this happens:
* User starts non-blocking commit to disable CRTC-1 on MST topology 1
* User starts non-blocking commit to enable CRTC-2 on MST topology 1
There's no guarantee here that the commit for disabling CRTC-2 will only
occur after CRTC-1 has finished, since neither commit shares a CRTC - only
the private modesetting object for MST. Keep in mind this likely isn't a
problem for blocking modesets, only non-blocking.
So, begin fixing this by keeping track of which CRTCs on a topology have
changed by keeping track of which CRTCs we release or allocate timeslots
on. As well, add some helpers for:
* Setting up the drm_crtc_commit structs in the ->commit_setup hook
* Waiting for any CRTC dependencies from the previous topology state
v2:
* Use drm_dp_mst_atomic_setup_commit() directly - Jani
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-9-lyude@redhat.com
We already open-code this quite often, and will be iterating through
payloads even more once we've moved all of the payload tracking into the
atomic state. So, let's add a helper for doing this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-8-lyude@redhat.com
Since we're about to start adding some stuff here, we may as well fill in
any missing documentation that we forgot to write.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-7-lyude@redhat.com
For some reason we mention returning 0 if "slots have been added back to
drm_dp_mst_topology_state->avail_slots". This is totally misleading,
avail_slots is simply for figuring out the total number of slots available
in total on the topology and has no relation to the current payload
allocations.
So, let's get rid of that comment.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-6-lyude@redhat.com
VCPI is only sort of the correct term here, originally the majority of this
code simply referred to timeslots vaguely as "slots" - and since I started
working on it and adding atomic functionality, the name "VCPI slots" has
been used to represent time slots.
Now that we actually have consistent access to the DisplayPort spec thanks
to VESA, I now know this isn't actually the proper term - as the
specification refers to these as time slots.
Since we're trying to make this code as easy to figure out as possible,
let's take this opportunity to correct this nomenclature and call them by
their proper name - timeslots. Likewise, we rename various functions
appropriately, along with replacing references in the kernel documentation
and various debugging messages.
It's important to note that this patch series leaves the legacy MST code
untouched for the most part, which is fine since we'll be removing it soon
anyhow. There should be no functional changes in this series.
v2:
* Add note that Wayne Lin from AMD suggested regarding slots being between
the source DP Tx and the immediate downstream DP Rx
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-5-lyude@redhat.com
In retrospect, the name I chose for this originally is confusing, as
there's a lot more info in here then just the VCPI. This really should be
called a payload. Let's make it more obvious that this is meant to be
related to the atomic state and is about payloads by renaming it to
drm_dp_mst_atomic_payload. Also, rename various variables throughout the
code that use atomic payloads.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <sean@poorly.run>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-4-lyude@redhat.com
This function isn't too confusing if you see the comment around the
call-site for it, but if you don't then it's not at all obvious this is
meant to copy DRM's payload table over to DC's internal state structs.
Seeing this function before finding that comment definitely threw me into a
loop a few times.
So, let's rename this to make it's purpose more obvious regardless of where
in the code you are.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-3-lyude@redhat.com
Just to make this more clear to outside contributors that these are
DC-specific structs, as this also threw me into a loop a number of times
before I figured out the purpose of this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817193847.557945-2-lyude@redhat.com
Add an eDP panel entry for IVO M133NW4J-R3.
Due to lack of documentation, use the delay_200_500_p2e100 timings for
now.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
[dianders: fixed typo in commit message]
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720054152.2450-1-steev@kali.org