Function memcpy_real() is an univeral data mover that does not
require DAT mode to be able reading from a physical address.
Its advantage is an ability to read from any address, even
those for which no kernel virtual mapping exists.
Although memcpy_real() is interrupt-safe, there are no handlers
that make use of this function. The compiler instrumentation
have to be disabled and separate no-DAT stack used to allow
execution of the function once DAT mode is disabled.
Rework memcpy_real() to overcome these shortcomings. As result,
data copying (which is primarily reading out a crashed system
memory by a user process) is executed on a regular stack with
enabled interrupts. Also, use of memcpy_real_buf swap buffer
becomes unnecessary and the swapping is eliminated.
The above is achieved by using a fixed virtual address range
that spans a single page and remaps that page repeatedly when
memcpy_real() is called for a particular physical address.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Temporary unsetting of the prefix page in memcpy_absolute() routine
poses a risk of executing code path with unexpectedly disabled prefix
page. This rework avoids the prefix page uninstalling and disabling
of normal and machine check interrupts when accessing the absolute
zero memory.
Although memcpy_absolute() routine can access the whole memory, it is
only used to update the absolute zero lowcore. This rework therefore
introduces a new mechanism for the absolute zero lowcore access and
scraps memcpy_absolute() routine for good.
Instead, an area is reserved in the virtual memory that is used for
the absolute lowcore access only. That area holds an array of 8KB
virtual mappings - one per CPU. Whenever a CPU is brought online, the
corresponding item is mapped to the real address of the previously
installed prefix page.
The absolute zero lowcore access works like this: a CPU calls the
new primitive get_abs_lowcore() to obtain its 8KB mapping as a
pointer to the struct lowcore. Virtual address references to that
pointer get translated to the real addresses of the prefix page,
which in turn gets swapped with the absolute zero memory addresses
due to prefixing. Once the pointer is not needed it must be released
with put_abs_lowcore() primitive:
struct lowcore *abs_lc;
unsigned long flags;
abs_lc = get_abs_lowcore(&flags);
abs_lc->... = ...;
put_abs_lowcore(abs_lc, flags);
To ensure the described mechanism works large segment- and region-
table entries must be avoided for the 8KB mappings. Failure to do
so results in usage of Region-Frame Absolute Address (RFAA) or
Segment-Frame Absolute Address (SFAA) large page fields. In that
case absolute addresses would be used to address the prefix page
instead of the real ones and the prefixing would get bypassed.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Rework copy_oldmem_page() callback to take an iov_iter.
This includes few prerequisite updates and fixes to the
oldmem reading code.
- Rework cpufeature implementation to allow for various CPU feature
indications, which is not only limited to hardware capabilities,
but also allows CPU facilities.
- Use the cpufeature rework to autoload Ultravisor module when CPU
facility 158 is available.
- Add ELF note type for encrypted CPU state of a protected virtual CPU.
The zgetdump tool from s390-tools package will decrypt the CPU state
using a Customer Communication Key and overwrite respective notes to
make the data accessible for crash and other debugging tools.
- Use vzalloc() instead of vmalloc() + memset() in ChaCha20 crypto test.
- Fix incorrect recovery of kretprobe modified return address in stacktrace.
- Switch the NMI handler to use generic irqentry_nmi_enter() and
irqentry_nmi_exit() helper functions.
- Rework the cryptographic Adjunct Processors (AP) pass-through design
to support dynamic changes to the AP matrix of a running guest as well
as to implement more of the AP architecture.
- Minor boot code cleanups.
- Grammar and typo fixes to hmcdrv and tape drivers.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQQrtrZiYVkVzKQcYivNdxKlNrRb8AUCYu4dRBccYWdvcmRlZXZA
bGludXguaWJtLmNvbQAKCRDNdxKlNrRb8DnlAP45Sk4cE35T+Z0vdHE2f0uMXE/p
uHNjS3fDZOQVFJ2jZwEA99xPF5qPCttbR/b1VHsMSb30684IT1A4PC7y05kgfAw=
=jCc3
-----END PGP SIGNATURE-----
Merge tag 's390-5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Alexander Gordeev:
- Rework copy_oldmem_page() callback to take an iov_iter.
This includes a few prerequisite updates and fixes to the oldmem
reading code.
- Rework cpufeature implementation to allow for various CPU feature
indications, which is not only limited to hardware capabilities, but
also allows CPU facilities.
- Use the cpufeature rework to autoload Ultravisor module when CPU
facility 158 is available.
- Add ELF note type for encrypted CPU state of a protected virtual CPU.
The zgetdump tool from s390-tools package will decrypt the CPU state
using a Customer Communication Key and overwrite respective notes to
make the data accessible for crash and other debugging tools.
- Use vzalloc() instead of vmalloc() + memset() in ChaCha20 crypto
test.
- Fix incorrect recovery of kretprobe modified return address in
stacktrace.
- Switch the NMI handler to use generic irqentry_nmi_enter() and
irqentry_nmi_exit() helper functions.
- Rework the cryptographic Adjunct Processors (AP) pass-through design
to support dynamic changes to the AP matrix of a running guest as
well as to implement more of the AP architecture.
- Minor boot code cleanups.
- Grammar and typo fixes to hmcdrv and tape drivers.
* tag 's390-5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (46 commits)
Revert "s390/smp: enforce lowcore protection on CPU restart"
Revert "s390/smp: rework absolute lowcore access"
Revert "s390/smp,ptdump: add absolute lowcore markers"
s390/unwind: fix fgraph return address recovery
s390/nmi: use irqentry_nmi_enter()/irqentry_nmi_exit()
s390: add ELF note type for encrypted CPU state of a PV VCPU
s390/smp,ptdump: add absolute lowcore markers
s390/smp: rework absolute lowcore access
s390/setup: rearrange absolute lowcore initialization
s390/boot: cleanup adjust_to_uv_max() function
s390/smp: enforce lowcore protection on CPU restart
s390/tape: fix comment typo
s390/hmcdrv: fix Kconfig "its" grammar
s390/docs: fix warnings for vfio_ap driver doc
s390/docs: fix warnings for vfio_ap driver lock usage doc
s390/crash: support multi-segment iterators
s390/crash: use static swap buffer for copy_to_user_real()
s390/crash: move copy_to_user_real() to crash_dump.c
s390/zcore: fix race when reading from hardware system area
s390/crash: fix incorrect number of bytes to copy to user space
...
This reverts commit 7d06fed77b.
This introduced vmem_mutex locking from vmem_map_4k_page()
function called from smp_reinit_ipl_cpu() with interrupts
disabled. While it is a pre-SMP early initcall no other CPUs
running in parallel nor other code taking vmem_mutex on this
boot stage - it still needs to be fixed.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Temporary unsetting of the prefix page in memcpy_absolute() routine
poses a risk of executing code path with unexpectedly disabled prefix
page. This rework avoids the prefix page uninstalling and disabling
of normal and machine check interrupts when accessing the absolute
zero memory.
Although memcpy_absolute() routine can access the whole memory, it is
only used to update the absolute zero lowcore. This rework therefore
introduces a new mechanism for the absolute zero lowcore access and
scraps memcpy_absolute() routine for good.
Instead, an area is reserved in the virtual memory that is used for
the absolute lowcore access only. That area holds an array of 8KB
virtual mappings - one per CPU. Whenever a CPU is brought online, the
corresponding item is mapped to the real address of the previously
installed prefix page.
The absolute zero lowcore access works like this: a CPU calls the
new primitive get_abs_lowcore() to obtain its 8KB mapping as a
pointer to the struct lowcore. Virtual address references to that
pointer get translated to the real addresses of the prefix page,
which in turn gets swapped with the absolute zero memory addresses
due to prefixing. Once the pointer is not needed it must be released
with put_abs_lowcore() primitive:
struct lowcore *abs_lc;
unsigned long flags;
abs_lc = get_abs_lowcore(&flags);
abs_lc->... = ...;
put_abs_lowcore(abs_lc, flags);
To ensure the described mechanism works large segment- and region-
table entries must be avoided for the 8KB mappings. Failure to do
so results in usage of Region-Frame Absolute Address (RFAA) or
Segment-Frame Absolute Address (SFAA) large page fields. In that
case absolute addresses would be used to address the prefix page
instead of the real ones and the prefixing would get bypassed.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Uncouple input and output arguments by making the latter
the function return value.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
We have information about the supported attestation header version
and plaintext attestation flag bits.
Let's expose it via the sysfs files.
Signed-off-by: Steffen Eiden <seiden@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Link: https://lore.kernel.org/lkml/20220601100245.3189993-1-seiden@linux.ibm.com/
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
- add an interface to provide a hypervisor dump for secure guests
- improve selftests to show tests
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+SKTgaM0CPnbq/vKEXu8gLWmHHwFAmKXf2wACgkQEXu8gLWm
HHzu1Q//WjEuOX5nBjklMUlDB2oB2+vFSyW9lE7x9m38EnFTH8QTfH695ChVoNN+
j06Fhd4ENjxqTTYs7z67tP4TSQ/LhB/GsPydKCEOnB/63+k2cnYeS3wsv19213F0
IyvpN6MkzxoktV4m1EtKhlvXGpEBoXZCczgBLj3FYlNQ7kO8RsSkF9rOnhuP9Yjh
l2876bWHWlbU0qWmRSAu0spkwHWjtyh/bnQKzXotQyrQ9bo1yMQvhe2HH8HVTSio
cjRlseWVi01rJKzKcs6D7MFMctLKr5y0onxBgGJnRh27KoBY195ICH2Jz2LfJoor
EP57YcXZqfxzKCGHTGgVYMgFeixX6nzBgqTpDIHMQzvoM1IrQKl+d5riepO03xpS
gZxHtJqZi8s+t8w0ZFBHj83VXkzFyLuCIeui9vo3cQ00K7bBrNUSw1BAdqT5HTzW
K2R4jSQaszjw8mDz3R3G1+yg6PjMS6cDEU1+G2Id7xSYTV3lJnBDVzas7aEUNCC4
LzIrD5c4dscyZzIjAp9huVwpZoCNLy6jtecRTaGhA2YiE0VMWtJlMJHwbShlSnM7
5VhEn859namvoYtN8XBaTFa/jRDOxO+LHWuOy172oaBUgaVHBjZQLyrlit1FRQvT
SVruCmgtJ7u7RD/8uVDfPNR05DTSWQYzklJoKx2avKZj5FIx7ms=
=/6Ue
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: pvdump and selftest improvements
- add an interface to provide a hypervisor dump for secure guests
- improve selftests to show tests
The new dump feature requires us to know how much memory is needed for
the "dump storage state" and "dump finalize" ultravisor call. These
values are reported via the UV query call.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Steffen Eiden <seiden@linux.ibm.com>
Link: https://lore.kernel.org/r/20220517163629.3443-3-frankja@linux.ibm.com
Message-Id: <20220517163629.3443-3-frankja@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
We have information about the supported se header version and pcf bits
so let's expose it via the sysfs files.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Steffen Eiden <seiden@linux.ibm.com>
Link: https://lore.kernel.org/r/20220517163629.3443-2-frankja@linux.ibm.com
Message-Id: <20220517163629.3443-2-frankja@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
- Add HOSTPKG_CONFIG env variable to allow users to override pkg-config
- Support W=e as a shorthand for KCFLAGS=-Werror
- Fix CONFIG_IKHEADERS build to support toybox cpio
- Add scripts/dummy-tools/pahole to ease distro packagers' life
- Suppress false-positive warnings from checksyscalls.sh for W=2 build
- Factor out the common code of arch/*/boot/install.sh into
scripts/install.sh
- Support 'kernel-install' tool in scripts/prune-kernel
- Refactor module-versioning to link the symbol versions at the final
link of vmlinux and modules
- Remove CONFIG_MODULE_REL_CRCS because module-versioning now works in
an arch-agnostic way
- Refactor modpost, Makefiles
-----BEGIN PGP SIGNATURE-----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=Y2TB
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add HOSTPKG_CONFIG env variable to allow users to override pkg-config
- Support W=e as a shorthand for KCFLAGS=-Werror
- Fix CONFIG_IKHEADERS build to support toybox cpio
- Add scripts/dummy-tools/pahole to ease distro packagers' life
- Suppress false-positive warnings from checksyscalls.sh for W=2 build
- Factor out the common code of arch/*/boot/install.sh into
scripts/install.sh
- Support 'kernel-install' tool in scripts/prune-kernel
- Refactor module-versioning to link the symbol versions at the final
link of vmlinux and modules
- Remove CONFIG_MODULE_REL_CRCS because module-versioning now works in
an arch-agnostic way
- Refactor modpost, Makefiles
* tag 'kbuild-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (56 commits)
genksyms: adjust the output format to modpost
kbuild: stop merging *.symversions
kbuild: link symbol CRCs at final link, removing CONFIG_MODULE_REL_CRCS
modpost: extract symbol versions from *.cmd files
modpost: add sym_find_with_module() helper
modpost: change the license of EXPORT_SYMBOL to bool type
modpost: remove left-over cross_compile declaration
kbuild: record symbol versions in *.cmd files
kbuild: generate a list of objects in vmlinux
modpost: move *.mod.c generation to write_mod_c_files()
modpost: merge add_{intree_flag,retpoline,staging_flag} to add_header
scripts/prune-kernel: Use kernel-install if available
kbuild: factor out the common installation code into scripts/install.sh
modpost: split new_symbol() to symbol allocation and hash table addition
modpost: make sym_add_exported() always allocate a new symbol
modpost: make multiple export error
modpost: dump Module.symvers in the same order of modules.order
modpost: traverse the namespace_list in order
modpost: use doubly linked list for dump_lists
modpost: traverse unresolved symbols in order
...
Get rid of old 31 bit leftovers within ipl code:
- convert everything to pc relative code
- use 64 bit addressing mode as early as possible
- use 64 bit arithmetics wherever possible
This way the code doesn't look as odd as before anymore.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
For at least the mvc and clc instructions llvm's integrated assembler can
generate incorrect code. In particular this happens with decompressor boot
code. The reason seems to be that relocations for the second displacement
of each instruction are at incorrect locations (-/+: gas vs llvm IAS):
mvc __LC_IO_NEW_PSW(16),.Lnewpsw
results in
4: d2 0f 01 f0 00 00 mvc 496(16,%r0),0
- 8: R_390_12 .head.text+0x10
+ 6: R_390_12 .head.text+0x10
and
clc 0(3,%r4),.L_hdr
results in
258: d5 02 40 00 00 00 clc 0(3,%r4),0
- 25c: R_390_12 .head.text+0x324
+ 25a: R_390_12 .head.text+0x324
Workaround this by writing the code in a different way.
Tested-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://github.com/llvm/llvm-project/issues/55411
Link: https://lore.kernel.org/r/20220511120532.2228616-7-hca@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Many architectures have similar install.sh scripts.
The first half is really generic; it verifies that the kernel image
and System.map exist, then executes ~/bin/${INSTALLKERNEL} or
/sbin/${INSTALLKERNEL} if available.
The second half is kind of arch-specific; it copies the kernel image
and System.map to the destination, but the code is slightly different.
Factor out the generic part into scripts/install.sh.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Convert parmarea to C, which makes it much easier to initialize it. No need
to keep offsets in assembler code in sync with struct parmarea anymore.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Convert initial lowcore to C and use proper defines and structures to
initialize it. This should make the z/VM ipl procedure a bit less magic.
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Initialize all new psws with disabled wait psws, except for the restart new
psw. This way every unexpected exception, svc, machine check, or interrupt
is handled properly.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The program check handler of the kernel image points to
startup_pgm_check_handler. However an early program check which happens
while loading the kernel image will jump to potentially random code, since
the code of the program check handler is not yet loaded; leading to a
program check loop.
Therefore initialize it to a disabled wait psw and let the startup code set
the proper psw when everything is in memory.
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Move iplstart entry point to 0x200 again, instead of the middle of the ipl
code. This way even the comment describing the ccw program is correct
again.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The final kernel image is created by linking decompressor object files with
a startup archive. The startup archive file however does not contain only
optional code and data which can be discarded if not referenced. It also
contains mandatory object data like head.o which must never be discarded,
even if not referenced.
Move the decompresser code and linker script to the boot directory and get
rid of the startup archive so everything is kept during link time.
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove my old invalid email address which can be found in a couple of
files. Instead of updating it, just remove my contact data completely
from source files.
We have git and other tools which allow to figure out who is responsible
for what with recent contact data.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Presumably, arch/{parisc,s390,sh}/boot/compressed/Makefile copied
arch/x86/boot/compressed/Makefile, but vmlinux.bin.all-y is useless
here because it is the same as $(obj)/vmlinux.bin.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
GZIP-compressed files end with 4 byte data that represents the size
of the original input. The decompressors (the self-extracting kernel)
exploit it to know the vmlinux size beforehand. To mimic the GZIP's
trailer, Kbuild provides cmd_{bzip2,lzma,lzo,lz4,xzkern,zstd22}.
Unfortunately these macros are used everywhere despite the appended
size data is only useful for the decompressors.
There is no guarantee that such hand-crafted trailers are safely ignored.
In fact, the kernel refuses compressed initramdfs with the garbage data.
That is why usr/Makefile overrides size_append to make it no-op.
To limit the use of such broken compressed files, this commit renames
the existing macros as follows:
cmd_bzip2 --> cmd_bzip2_with_size
cmd_lzma --> cmd_lzma_with_size
cmd_lzo --> cmd_lzo_with_size
cmd_lz4 --> cmd_lz4_with_size
cmd_xzkern --> cmd_xzkern_with_size
cmd_zstd22 --> cmd_zstd22_with_size
To keep the decompressors working, I updated the following Makefiles
accordingly:
arch/arm/boot/compressed/Makefile
arch/h8300/boot/compressed/Makefile
arch/mips/boot/compressed/Makefile
arch/parisc/boot/compressed/Makefile
arch/s390/boot/compressed/Makefile
arch/sh/boot/compressed/Makefile
arch/x86/boot/compressed/Makefile
I reused the current macro names for the normal usecases; they produce
the compressed data in the proper format.
I did not touch the following:
arch/arc/boot/Makefile
arch/arm64/boot/Makefile
arch/csky/boot/Makefile
arch/mips/boot/Makefile
arch/riscv/boot/Makefile
arch/sh/boot/Makefile
kernel/Makefile
This means those Makefiles will stop appending the size data.
I dropped the 'override size_append' hack from usr/Makefile.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Initial KASAN shadow memory range was picked to preserve original kernel
modules area position. With protected execution support, which might
impose addressing limitation on vmalloc area and hence affect modules
area position, current fixed KASAN shadow memory range is only making
kernel memory layout setup more complex. So move it to the very end of
available virtual space and simplify calculations.
At the same time return to previous kernel address space split. In
particular commit 0c4f2623b9 ("s390: setup kernel memory layout
early") introduced precise identity map size calculation and keeping
vmemmap left most starting from a fresh region table entry. This didn't
take into account additional mapping region requirement for potential
DCSS mapping above available physical memory. So go back to virtual
space split between 1:1 mapping & vmemmap array once vmalloc area size
is subtracted.
Cc: stable@vger.kernel.org
Fixes: 0c4f2623b9 ("s390: setup kernel memory layout early")
Reported-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently s390 supports a fixed maximum command line length of 896
bytes. This isn't enough as some installers are trying to pass all
configuration data via kernel command line, and even with zfcp alone
it is easy to generate really long command lines. Therefore extend
the command line to 4 kbytes.
In the parm area where the command line is stored there is no indication
of the maximum allowed length, so a new field which contains the maximum
length is added.
The parm area has always been initialized to zero, so with old kernels
this field would read zero. This is important because tools like zipl
could read this field. If it contains a number larger than zero zipl
knows the maximum length that can be stored in the parm area, otherwise
it must assume that it is booting a legacy kernel and only 896 bytes are
available.
The removing of trailing whitespace in head.S is also removed because
code to do this is already present in setup_boot_command_line().
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
In preparation of adding support for command lines with variable
sizes on s390, the check whether the new kernel image is at least HEAD_END
bytes long isn't correct. Move the check to kexec_file_add_components()
so we can get the size of the parm area and check the size there.
The '.org HEAD_END' directive can now also be removed from head.S. This
was used in the past to reserve space for the early sccb buffer, but with
commit 9a5131b87cac1 ("s390/boot: move sclp early buffer from fixed address
in asm to C") this is no longer required.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With the upcoming BEAR enhancements last_break isn't really
unique, so rename it to pgm_last_break. This way it should
be more obvious that this is the last_break value that is
written by the hardware when a program check occurs.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The memory for amode31 section is allocated from the decompressed
kernel. Instead, allocate that memory from the decompressor. This
is a prerequisite to allow initialization of the virtual memory
before the decompressed kernel takes over.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Partially revert commit 4555b9f34296 ("s390/boot: move
dma sections from decompressor to decompressed kernel").
This is a prerequisite to allow initialization of virtual
memory in decompressor and avoid overwriting of ASCEs in
the decompressed kernel otherwise.
Since the control registers 2, 5 and 15 are reinitialized
in the decompressed kernel again, this change does not
prevent relocating of amode31 section in any way.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Add -s option (strict mode) to merge_config.sh to make it fail when
any symbol is redefined.
- Show a warning if a different compiler is used for building external
modules.
- Infer --target from ARCH for CC=clang to let you cross-compile the
kernel without CROSS_COMPILE.
- Make the integrated assembler default (LLVM_IAS=1) for CC=clang.
- Add <linux/stdarg.h> to the kernel source instead of borrowing
<stdarg.h> from the compiler.
- Add Nick Desaulniers as a Kbuild reviewer.
- Drop stale cc-option tests.
- Fix the combination of CONFIG_TRIM_UNUSED_KSYMS and CONFIG_LTO_CLANG
to handle symbols in inline assembly.
- Show a warning if 'FORCE' is missing for if_changed rules.
- Various cleanups
-----BEGIN PGP SIGNATURE-----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=lw3M
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add -s option (strict mode) to merge_config.sh to make it fail when
any symbol is redefined.
- Show a warning if a different compiler is used for building external
modules.
- Infer --target from ARCH for CC=clang to let you cross-compile the
kernel without CROSS_COMPILE.
- Make the integrated assembler default (LLVM_IAS=1) for CC=clang.
- Add <linux/stdarg.h> to the kernel source instead of borrowing
<stdarg.h> from the compiler.
- Add Nick Desaulniers as a Kbuild reviewer.
- Drop stale cc-option tests.
- Fix the combination of CONFIG_TRIM_UNUSED_KSYMS and CONFIG_LTO_CLANG
to handle symbols in inline assembly.
- Show a warning if 'FORCE' is missing for if_changed rules.
- Various cleanups
* tag 'kbuild-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kbuild: redo fake deps at include/ksym/*.h
kbuild: clean up objtool_args slightly
modpost: get the *.mod file path more simply
checkkconfigsymbols.py: Fix the '--ignore' option
kbuild: merge vmlinux_link() between ARCH=um and other architectures
kbuild: do not remove 'linux' link in scripts/link-vmlinux.sh
kbuild: merge vmlinux_link() between the ordinary link and Clang LTO
kbuild: remove stale *.symversions
kbuild: remove unused quiet_cmd_update_lto_symversions
gen_compile_commands: extract compiler command from a series of commands
x86: remove cc-option-yn test for -mtune=
arc: replace cc-option-yn uses with cc-option
s390: replace cc-option-yn uses with cc-option
ia64: move core-y in arch/ia64/Makefile to arch/ia64/Kbuild
sparc: move the install rule to arch/sparc/Makefile
security: remove unneeded subdir-$(CONFIG_...)
kbuild: sh: remove unused install script
kbuild: Fix 'no symbols' warning when CONFIG_TRIM_UNUSD_KSYMS=y
kbuild: Switch to 'f' variants of integrated assembler flag
kbuild: Shuffle blank line to improve comment meaning
...
- Improve ftrace code patching so that stop_machine is not required anymore.
This requires a small common code patch acked by Steven Rostedt:
https://lore.kernel.org/linux-s390/20210730220741.4da6fdf6@oasis.local.home/
- Enable KCSAN for s390. This comes with a small common code change to fix a
compile warning. Acked by Marco Elver:
https://lore.kernel.org/r/20210729142811.1309391-1-hca@linux.ibm.com
- Add KFENCE support for s390. This also comes with a minimal x86 patch from
Marco Elver who said also this can be carried via the s390 tree:
https://lore.kernel.org/linux-s390/YQJdarx6XSUQ1tFZ@elver.google.com/
- More changes to prepare the decompressor for relocation.
- Enable DAT also for CPU restart path.
- Final set of register asm removal patches; leaving only three locations where
needed and sane.
- Add NNPA, Vector-Packed-Decimal-Enhancement Facility 2, PCI MIO support to
hwcaps flags.
- Cleanup hwcaps implementation.
- Add new instructions to in-kernel disassembler.
- Various QDIO cleanups.
- Add SCLP debug feature.
- Various other cleanups and improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=WDRh
-----END PGP SIGNATURE-----
Merge tag 's390-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Improve ftrace code patching so that stop_machine is not required
anymore. This requires a small common code patch acked by Steven
Rostedt:
https://lore.kernel.org/linux-s390/20210730220741.4da6fdf6@oasis.local.home/
- Enable KCSAN for s390. This comes with a small common code change to
fix a compile warning. Acked by Marco Elver:
https://lore.kernel.org/r/20210729142811.1309391-1-hca@linux.ibm.com
- Add KFENCE support for s390. This also comes with a minimal x86 patch
from Marco Elver who said also this can be carried via the s390 tree:
https://lore.kernel.org/linux-s390/YQJdarx6XSUQ1tFZ@elver.google.com/
- More changes to prepare the decompressor for relocation.
- Enable DAT also for CPU restart path.
- Final set of register asm removal patches; leaving only three
locations where needed and sane.
- Add NNPA, Vector-Packed-Decimal-Enhancement Facility 2, PCI MIO
support to hwcaps flags.
- Cleanup hwcaps implementation.
- Add new instructions to in-kernel disassembler.
- Various QDIO cleanups.
- Add SCLP debug feature.
- Various other cleanups and improvements all over the place.
* tag 's390-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (105 commits)
s390: remove SCHED_CORE from defconfigs
s390/smp: do not use nodat_stack for secondary CPU start
s390/smp: enable DAT before CPU restart callback is called
s390: update defconfigs
s390/ap: fix state machine hang after failure to enable irq
KVM: s390: generate kvm hypercall functions
s390/sclp: add tracing of SCLP interactions
s390/debug: add early tracing support
s390/debug: fix debug area life cycle
s390/debug: keep debug data on resize
s390/diag: make restart_part2 a local label
s390/mm,pageattr: fix walk_pte_level() early exit
s390: fix typo in linker script
s390: remove do_signal() prototype and do_notify_resume() function
s390/crypto: fix all kernel-doc warnings in vfio_ap_ops.c
s390/pci: improve DMA translation init and exit
s390/pci: simplify CLP List PCI handling
s390/pci: handle FH state mismatch only on disable
s390/pci: fix misleading rc in clp_set_pci_fn()
s390/boot: factor out offset_vmlinux_info() function
...
Move offsetting all of vmlinux_info fields to a separate
function for better readability.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Ship minimal stdarg.h (1 type, 4 macros) as <linux/stdarg.h>.
stdarg.h is the only userspace header commonly used in the kernel.
GPL 2 version of <stdarg.h> can be extracted from
http://archive.debian.org/debian/pool/main/g/gcc-4.2/gcc-4.2_4.2.4.orig.tar.gz
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Currently, the install target in arch/s390/Makefile descends into
arch/s390/boot/Makefile to invoke the shell script, but there is no
good reason to do so.
arch/s390/Makefile can run the shell script directly.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210729142338.446002-1-masahiroy@kernel.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
zstd decompression uses __builtin_clz() which fails back to __clzdi2()
when the kernel is built for older hardware like z900. This leads to
build failures like the following:
s390x-11.1.0-ld: /devel/src/kernel/arch/s390/boot/compressed/../../../../lib/zstd/bitstream.h:148: undefined reference to `__clzdi2'
Fix that by optionally including lib/clz_ctz.c into the decompressor.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 7b034d9c1b ("s390/boot: add zstd support")
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Link: https://lore.kernel.org/r/patch-1.thread-f0f589.git-f0f58936888f.your-ad-here.call-01627564869-ext-2765@work.hours
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
This change simplifies the task of making the decompressor relocatable.
The decompressor's image contains special DMA sections between _sdma and
_edma. This DMA segment is loaded at boot as part of the decompressor and
then simply handed over to the decompressed kernel. The decompressor itself
never uses it in any way. The primary reason for this is the need to keep
the aforementioned DMA segment below 2GB which is required by architecture,
and because the decompressor is always loaded at a fixed low physical
address, it is guaranteed that the DMA region will not cross the 2GB
memory limit. If the DMA region had been placed in the decompressed kernel,
then KASLR would make this guarantee impossible to fulfill or it would
be restricted to the first 2GB of memory address space.
This commit moves all DMA sections between _sdma and _edma from
the decompressor's image to the decompressed kernel's image. The complete
DMA region is placed in the init section of the decompressed kernel and
immediately relocated below 2GB at start-up before it is needed by other
parts of the decompressed kernel. The relocation of the DMA region happens
even if the decompressed kernel is already located below 2GB in order
to keep the first implementation simple. The relocation should not have
any noticeable impact on boot time because the DMA segment is only a couple
of pages.
After relocating the DMA sections, the kernel has to fix all references
which point into it. In order to automate this, place all variables
pointing into the DMA sections in a special .dma.refs section. All such
variables must be defined using the new __dma_ref macro. Only variables
containing addresses within the DMA sections must be placed in the new
.dma.refs section.
Furthermore, move the initialization of control registers from
the decompressor to the decompressed kernel because some control registers
reference tables that must be placed in the DMA data section to
guarantee that their addresses are below 2G. Because the decompressed
kernel relocates the DMA sections at startup, the content of control
registers CR2, CR5 and CR15 must be updated with new addresses after
the relocation. The decompressed kernel initializes all control registers
early at boot and then updates the content of CR2, CR5 and CR15
as soon as the DMA relocation has occurred. This practically reverts
the commit a80313ff91 ("s390/kernel: introduce .dma sections").
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
As a preparation for moving the .dma.data section from the decompressor to
the decompressed kernel, the .dma.data section must be made relocatable
by replacing absolute memory addressing with relative one. This is required
in order to be able to relocate the DMA section to a memory address <= 2G
as required by the hardware architecture. The DMA section must be
relocated in case the decompressed kernel was loaded to an address >= 2G
which can occur if KASAN is enabled. By making the whole DMA section
position-independent we avoid applying relocations to it whenever it is
moved to a different address, which becomes possible as soon as it becomes
a part of the decompressed kernel.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Both macros are used only in decompressor's head.S, unnecessary to put
them in a global header used in many places like setup.h is.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The new boot data struct shall replace global variables OLDMEM_BASE and
OLDMEM_SIZE. It is initialized in the decompressor and passed
to the decompressed kernel. In comparison to the old solution, this one
doesn't access data at fixed physical addresses which will become important
when the decompressor becomes relocatable.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The new boot data struct shall replace global variables INITRD_START and
INITRD_SIZE. It is initialized in the decompressor and passed
to the decompressed kernel. In comparison to the old solution, this one
doesn't access data at fixed physical addresses which will become important
when the decompressor becomes relocatable.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
To make the decompressor relocatable, the early SCLP buffer with a fixed
address must be replaced with a relocatable C buffer of the according size
and alignment as required by SCLP.
Introduce a new function sclp_early_set_buffer() into the SCLP driver
which enables the decompressor to change the SCLP early buffer at any time.
This will be useful when the decompressor becomes fully relocatable and
might need to change the SCLP early buffer to one with an address < 2G
as required by SCLP because it was loaded at an address >= 2G.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use STARTUP_NORMAL_OFFSET and STARTUP_KDUMP_OFFSET instead of magic numbers.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
De-duplicate checks for Protected Host Virtualization in decompressor and
kernel.
Set prot_virt_host=0 in the decompressor in *any* of the following cases
and hand it over to the decompressed kernel:
* No explicit prot_virt=1 is given on the kernel command-line
* Protected Guest Virtualization is enabled
* Hardware support not present
* kdump or stand-alone dump
The decompressed kernel needs to use only is_prot_virt_host() instead of
performing again all checks done by the decompressor.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
A dump kernel is neither required nor able to support Secure Execution.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The functions adjust_to_uv_max() and uv_query_info() are used only
in the decompressor. Therefore, move the function declarations from
the global arch/s390/include/asm/uv.h to arch/s390/boot/uv.h.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
A buffer that can be used for communication with SCLP is required
to lie below 2GB memory address. Therefore, both sclp_info_sccb
and sclp_early_sccb must fulfill this requirement if passed directly
to the sclp_early_cmd() function. Instead, use only sclp_early_sccb
for communication with SCLP. This allows the buffer sclp_info_sccb
to be placed anywhere in the memory address space and, therefore,
simplifies the process of making the decompressor relocatable later on,
one thing less to relocate. And make sure that the length of the new unified
early SCLP buffer is no less than the length of the removed sclp_info_sccb
buffer which might be larger than the length of the sclp_early_sccb buffer.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
* The linux/spinlock.h header was included indirectly by the decompressor
and brought unnecessary build dependencies.
* Use proper includes in files which either directly or indirectly included
cio.h and were hidden until now by the included linux/spinlock.h, e.g.
linux/string.h for memcpy() or asm/page.h for PAGE_SIZE.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Instead of using constant addresses for the normal and dump-info stacks,
allocate both stacks in the decompressor's image and load the stack register
in a position-independent manner.
This will allow loading and entering the decompressor at an arbitrary
memory address without corrupting the content at the fixed addresses
used until now for both stacks. This is one of the prerequisites
for being able to kexec the decompressor from its load address without
relocating it first.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
To prevent multiple incompatible declarations of symbols and to catch
such mistakes at compile time.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The DMA code section of the decompressor must be compiled with expolines
if Spectre V2 mitigation has been enabled for the decompressed kernel.
This is required because although the decompressor's image contains
the DMA code section, it is handed over to the decompressed kernel for use.
Because the DMA code is already slow w/o expolines, use expolines always
regardless whether the decompressed kernel is using them or not. This
simplifies the DMA code by dropping the conditional compilation of
expolines.
Fixes: bf72630130 ("s390: use proper expoline sections for .dma code")
Cc: <stable@vger.kernel.org> # 5.2
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The magic string "S390EP" at offset 0x10008 indicated to the decompressed
kernel that it was booted by the decompressor. Introduce a new bootdata
flag instead which conveys the same information in an explicit and
a cleaner way. But keep the magic string because it is a kernel ABI.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Turns out that the bit 61 in the TEID is not always 1 and if that's
the case the address space ID and the address are
unpredictable. Without an address and its address space ID we can't
export memory and hence we can only send a SIGSEGV to the process or
panic the kernel depending on who caused the exception.
Unfortunately bit 61 is only reliable if we have the "misc" UV feature
bit.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 084ea4d611 ("s390/mm: add (non)secure page access exceptions handlers")
Cc: stable@vger.kernel.org
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The tprot() inline asm temporarily changes the program check new psw
to redirect a potential program check on the diag instruction.
Restoring of the program check new psw is done in C code behind the
inline asm.
This can be problematic, especially if the function is inlined, since
the compiler can reorder instructions in such a way that a different
instruction, which may result in a program check, might be executed
before the program check new psw has been restored.
To avoid such a scenario move restoring into the inline asm. For
consistency reasons move also saving of the original program check new
psw into the inline asm.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The __diag260() inline asm temporarily changes the program check new
psw to redirect a potential program check on the diag instruction.
Restoring of the program check new psw is done in C code behind the
inline asm.
This can be problematic, especially if the function is inlined, since
the compiler can reorder instructions in such a way that a different
instruction, which may result in a program check, might be executed
before the program check new psw has been restored.
To avoid such a scenario move restoring into the inline asm. For
consistency reasons move also saving of the original program check new
psw into the inline asm.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The __diag308() inline asm temporarily changes the program check new
psw to redirect a potential program check on the diag instruction.
Restoring of the program check new psw is done in C code behind the
inline asm.
This can be problematic, especially if the function is inlined, since
the compiler can reorder instructions in such a way that a different
instruction, which may result in a program check, might be executed
before the program check new psw has been restored.
To avoid such a scenario move restoring into the inline asm. For
consistency reasons move also saving of the original program check new
psw into the inline asm.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Enable ztsd support in s390/boot, to enable booting with zstd
compressed kernel when configured with CONFIG_KERNEL_ZSTD=y.
BOOT_HEAP_SIZE is defined to 0x30000 in this case. Actual decompressor
memory usage with allyesconfig is currently 0x26150.
BugLink: https://bugs.launchpad.net/bugs/1931725
Signed-off-by: Dimitri John Ledkov <dimitri.ledkov@canonical.com>
cc: Heiko Carstens <hca@linux.ibm.com>
cc: Vasily Gorbik <gor@linux.ibm.com>
cc: Christian Borntraeger <borntraeger@de.ibm.com>
cc: linux-s390@vger.kernel.org
Link: https://lore.kernel.org/r/20210615114150.325080-1-dimitri.ledkov@canonical.com
[gor: added BOOT_HEAP_SIZE for zstd]
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently BOOT_HEAP_SIZE is always defined as 0x400000 due to
bogus condition. Use CONFIG_KERNEL_BZIP2 instead of
CONFIG_HAVE_KERNEL_BZIP2 to correct that.
BOOT_HEAP_SIZE of 0x10000 is still good enough for every decompressor
algorithm but bzip2. Actual decompressor memory usage with allyesconfig
is the following:
gzip 0xbc28
bzip2 0x379518
xz 0x7410
lzma 0x3e6c
lzo 0
lz4 0
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently there are two separate places where kernel memory layout has
to be known and adjusted:
1. early kasan setup.
2. paging setup later.
Those 2 places had to be kept in sync and adjusted to reflect peculiar
technical details of one another. With additional factors which influence
kernel memory layout like ultravisor secure storage limit, complexity
of keeping two things in sync grew up even more.
Besides that if we look forward towards creating identity mapping and
enabling DAT before jumping into uncompressed kernel - that would also
require full knowledge of and control over kernel memory layout.
So, de-duplicate and move kernel memory layout setup logic into
the decompressor.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Use simple sed/tr instead of perl to generate decompressor symbols
file with the same result.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
[gor: changed commit message]
Link: https://lore.kernel.org/r/a48c51f8-5fe4-87e7-284e-c96e2381801a@landley.net
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Access the kernel command line via parmarea instead of using the
COMMAND_LINE define.
With this the following gcc11 warning is removed:
arch/s390/boot/ipl_parm.c: In function ‘setup_boot_command_line’:
arch/s390/boot/ipl_parm.c:168:50: warning: writing 1 byte into a region of size 0 [-Wstringop-overflow=]
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit 9a965ea95135 ("s390/kexec_file: Simplify parmarea
access") we have struct parmarea which describes the layout of the
kernel parameter area.
Make the kernel parameter area available as global variable parmarea
of type struct parmarea, which allows to easily access its members.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With gcc-11, there are a lot of warnings because the facility functions
are accessing lowcore through a null pointer. Fix this by moving the
facility arrays away from lowcore.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The number reported by the query is N-1 and I think people reading the
sysfs file would expect N instead. For users creating VMs there's no
actual difference because KVM's limit is currently below the UV's
limit.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Fixes: a0f60f8431 ("s390/protvirt: Add sysfs firmware interface for Ultravisor information")
Cc: stable@vger.kernel.org
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With the intoduction of hardware tag-based KASAN some kernel checks of
this kind:
ifdef CONFIG_KASAN
will be updated to:
if defined(CONFIG_KASAN_GENERIC) || defined(CONFIG_KASAN_SW_TAGS)
x86 and s390 use a trick to #undef CONFIG_KASAN for some of the code
that isn't linked with KASAN runtime and shouldn't have any KASAN
annotations.
Also #undef CONFIG_KASAN_GENERIC with CONFIG_KASAN.
Link: https://lkml.kernel.org/r/9d84bfaaf8fabe0fc89f913c9e420a30bd31a260.1606161801.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Marco Elver <elver@google.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Branislav Rankov <Branislav.Rankov@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Kevin Brodsky <kevin.brodsky@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More and more functionality from the early boot phase gets carried over
to the decompressor. With this the complexity of the code and thus the
chance to introduce bugs increases. In order to be able to debug these
early boot bugs the distributions have to package the decompressors
vmlinux together with the other debuginfos. However for that the
distributions require the vmlinux to contain a build-id.
Per default the section containing the build-id is placed first in the
section table. So make sure to move it behind the .text section
otherwise the image would be unbootable.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Add kernel command line and last breaking event.
The kernel command line is taken from early_command_line and printed
only if kernel is not running as protected virtualization guest and
if it has been already initialized from the "COMMAND_LINE".
Linux version 5.10.0-rc3-22794-gecaa72788df0-dirty (gor@tuxmaker) #28 SMP PREEMPT Mon Nov 9 17:41:20 CET 2020
Kernel command line: audit_enable=0 audit=0 selinux=0 crashkernel=296M root=/dev/dasda1 dasd=ec5b
memblock=debug die
Kernel fault: interruption code 0005 ilc:2
PSW : 0000000180000000 0000000000012f92 (parse_boot_command_line+0x27a/0x46c)
R:0 T:0 IO:0 EX:0 Key:0 M:0 W:0 P:0 AS:0 CC:0 PM:0 RI:0 EA:3
GPRS: 0000000000000000 00ffffffffffffff 0000000000000000 000000000001a65c
000000000000bf60 0000000000000000 00000000000003c0 0000000000000000
0000000000000080 000000000002322d 000000007f29ef20 0000000000efd018
000000000311c000 0000000000010070 0000000000012f82 000000000000bea8
Call Trace:
(sp:000000000000bea8 [<000000000002016e>] 000000000002016e)
sp:000000000000bf18 [<0000000000012408>] startup_kernel+0x88/0x2fc
sp:000000000000bf60 [<00000000000100c4>] startup_normal+0xb0/0xb0
Last Breaking-Event-Address:
[<00000000000135ba>] strcmp+0x22/0x24
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Acked-by: Viktor Mihajlovski <mihajlov@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Information printed by print_pgm_check_info() is crucial for
debugging decompressor problems. Printing instruction addresses is
better than nothing, but turns further debugging into tedious job of
figuring out which function those addresses correspond to.
This change adds simplistic symbols resolution support. And adds %pS
format specifier support to decompressor_printk().
Decompressor symbols list is extracted and sorted with
nm -n -S:
...
0000000000010000 0000000000000014 T startup
0000000000010014 00000000000000b0 t startup_normal
0000000000010180 00000000000000b2 t startup_kdump
...
Then functions are filtered and contracted to a form:
"10000 14 startup\0""10014 b0 startup_normal\0""10180 b2 startup_kdump\0"
...
Which makes it trivial to find beginning of an entry and names are 0
terminated, so could be used as is. Symbols are binary-searched.
To get symbols list with final addresses and then get it into the
decompressor's image the same trick as for kallsyms is used.
Decompressor's vmlinux is linked twice.
Symbols are stored in .decompressor.syms section, current size is about
2kb.
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use SYM_CODE_* annotations for asm functions, so that function lengths
are recognized correctly.
Also currently the most part of startup is marked as startup_kdump. Move
misplaced startup_kdump where it belongs.
$ nm -n -S arch/s390/boot/compressed/vmlinux
Before:
0000000000010000 T startup
0000000000010010 T startup_kdump
After:
0000000000010000 0000000000000014 T startup
0000000000010014 00000000000000b0 t startup_normal
0000000000010180 00000000000000b2 t startup_kdump
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The decompressor does not have any special debug means. Running the
kernel under qemu with gdb is helpful but tedious exercise if done
repeatedly. It is also not applicable to debugging under LPAR and z/VM.
One special thing which stands out is a working sclp_early_printk,
which could be used once the kernel switches to 64-bit addressing mode.
But sclp_early_printk does not provide any string formating capabilities.
Formatting and printing string without printk-alike function is a
not fun. The lack of printk-alike function means people would save up on
testing and introduce more bugs.
So, finally, provide decompressor_printk function, which fits on one
screen and trades features for simplicity.
It only supports "%s", "%x" and "%lx" specifiers and zero padding for
hex values.
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently we have to consider too many different values which
in the end only affect identity mapping size. These are:
1. max_physmem_end - end of physical memory online or standby.
Always <= end of the last online memory block (get_mem_detect_end()).
2. CONFIG_MAX_PHYSMEM_BITS - the maximum size of physical memory the
kernel is able to support.
3. "mem=" kernel command line option which limits physical memory usage.
4. OLDMEM_BASE which is a kdump memory limit when the kernel is executed as
crash kernel.
5. "hsa" size which is a memory limit when the kernel is executed during
zfcp/nvme dump.
Through out kernel startup and run we juggle all those values at once
but that does not bring any amusement, only confusion and complexity.
Unify all those values to a single one we should really care, that is
our identity mapping size.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
And move it earlier in the decompressor.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Fixes the following warning with CONFIG_KERNEL_UNCOMPRESSED=y
arch/s390/boot/compressed/decompressor.h:6:46: warning: non-void function
does not return a value [-Wreturn-type]
static inline void *decompress_kernel(void) {}
^
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
To make sure that the vmalloc area size is for almost all cases large
enough let it depend on the (potential) physical memory size. There is
still the possibility to override this with the vmalloc kernel command
line parameter.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Set io/ext handlers to disabled wait in the initial lowcore, so that they
are effective right from the kernel start, when a boot method used does
not rewrite this part of the lowcore for its own needs (i.e. kexec, z/vm
ipl reader boot, qemu direct boot, load from removable media or server).
When the kernel is loaded by zipl, scsi loader or qemu loader, some or
all of the io/ext/pgm handlers addresses might be rewritten. Rewrite them
to initial values again as early as possible.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Early sclp console messages are printed in line mode on z/VM and LPAR,
but under kvm newlines matter. Add a missing newline between "kernel
version" and "Kernel fault".
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
From the kernel perspective NVMe dump works exactly like zFCP dump.
Therefore, adapt all places where code explicitly tests only for
IPL of type FCP DUMP. And also set the memory end correctly in this case.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Enable extracting of extra kernel command-line parameters
from the NVMe IPL block passed by the firmware to the kernel
at boot.
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
startup pgm check handler is active since the very beginning of kernel
code execution until uncompressed kernel sets up s390_base_pgm_handler.
It is useful not just for the decompressor debugging itself, but also for
early code of uncompressed kernel, in particular Kasan initialization. But
since there is no stack trace or symbolic representation of failing psw
address it is impossible to figure out faulty code location without
knowing Kaslr kernel base. So, let's add it to the startup pgm check
info printed as well.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently if just "dfltcc" is passed as a kernel command line option
"val" going to be NULL, this leads to reading at address 0 in
strcmp(val, "off")
Fix that by making sure "val" is not NULL. This does not affect option
handling logic.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently we overflow save_area_sync and write over
save_area_async. Although this is not a real problem make
startup_pgm_check_handler consistent with late pgm check handler and
store [%r0,%r7] directly into gpregs_save_area.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Since commit 394216275c ("s390: remove broken hibernate / power
management support") _swsusp_reset_dma is unused and could be safely
removed.
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently there are several minor problems with randomization base
generation code:
1. It might misbehave in low memory conditions. In particular there
might be enough space for the kernel on [0, block_sum] but after
if (base < safe_addr)
base = safe_addr;
it might not be enough anymore.
2. It does not correctly handle minimal address constraint. In condition
if (base < safe_addr)
base = safe_addr;
a synthetic value is compared with an address. If we have a memory
setup with memory holes due to offline memory regions, and safe_addr is
close to the end of the first online memory block - we might position
the kernel in invalid memory.
3. block_sum calculation logic contains off-by-one error. Let's say we
have a memory block in which the kernel fits perfectly
(end - start == kernel_size). In this case:
if (end - start < kernel_size)
continue;
block_sum += end - start - kernel_size;
block_sum is not increased, while it is a valid kernel position.
So, address problems listed and explain algorithm used. Besides that
restructuring the code makes it possible to extend kernel positioning
algorithm further. Currently we pick position in between single
[min, max] range (min = safe_addr, max = memory_limit). In future we
can do that for multiple ranges as well (by calling
count_valid_kernel_positions for each range).
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
0 is a valid random value. To avoid mixing it with error code 0 as an
return code make get_random() take extra argument to output random
value and return an error code.
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
.bss section is a part of the decompressor's image now, linker fills it
with zeros already. No need do it with memset additionally.
Reviewed-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
To make early kernel address space layout definition possible parse
prot_virt option in the decompressor and pass it to the uncompressed
kernel. This enables kasan to take ultravisor secure storage limit into
consideration and pre-define vmalloc position correctly.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Support static uninitialized variables in compressed kernel.
- Remove chkbss script
- Get rid of workarounds for not having .bss section
Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The include/linux/pgtable.h is going to be the home of generic page table
manipulation functions.
Start with moving asm-generic/pgtable.h to include/linux/pgtable.h and
make the latter include asm/pgtable.h.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-3-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel fails to compile with CONFIG_PROTECTED_VIRTUALIZATION_GUEST
set but CONFIG_KVM unset.
This patch fixes the issue by making the needed variable always available.
Link: https://lkml.kernel.org/r/20200423120114.2027410-1-imbrenda@linux.ibm.com
Fixes: a0f60f8431 ("s390/protvirt: Add sysfs firmware interface for Ultravisor information")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Philipp Rudo <prudo@linux.ibm.com>
Suggested-by: Philipp Rudo <prudo@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth Vijayan
common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other fixes/improvements
in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios
mm cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6Ig2YACgkQjYWKoQLX
FBj2gggAibnHOl9d0ngX1mVT4nz51R3V8z5sEQjNMr2uHBmaTqs7pi/00gaFMxoC
NngVEXvL443jSogQivthGgXPpRCV9xdKE3sp38j7fF4LgHoeuDtGd1oaX4W9Rqk0
7Yii35EaO2e2WHdOKaAbu+ZvDRunFjERyntc51MYaIUivFosogSo07vC73vFIArF
VGStS09fJ4Ny76ott896T7Ulx1Iek/MkF1vponEMLGNUIcLIQbbxZxOwgz0pHuEF
SlyyJBnhOIaAJGOYlKREQDt1cew+hsxluPU+a01bwdsmdZv9LH1BGwLayDqTH58i
QWvtEpzJFmDvo9jGM1v81ebaGnyCKg==
=hiGF
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth
Vijayan common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other
fixes/improvements in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios mm
cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
* tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (57 commits)
s390/mm: cleanup init_new_context() callback
s390/mm: cleanup virtual memory constants usage
s390/mm: remove page table downgrade support
s390/qdio: set qdio_irq->cdev at allocation time
s390/qdio: remove unused function declarations
s390/ccwgroup: remove pm support
s390/ap: remove power management code from ap bus and drivers
s390/zcrypt: use kvmalloc instead of kmalloc for 256k alloc
s390/mm: cleanup arch_get_unmapped_area() and friends
s390/ism: remove pm support
s390/cio: use fallthrough;
s390/vfio: use fallthrough;
s390/zcrypt: use fallthrough;
s390: use fallthrough;
s390/cpum_sf: Fix wrong page count in error message
s390/diag: fix display of diagnose call statistics
s390/ap: Remove ap device suspend and resume callbacks
s390/pci: Improve handling of unset UID
s390/pci: Fix zpci_alloc_domain() over allocation
s390/qdio: pass ISC as parameter to chsc_sadc()
...
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
Alexander Gordeev