i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.
General features:
CPU NXP i.MX6Q rev1.2 at 792 MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
LVDS Display TFT 12.3" industrial, 1280x480 resolution
Backlight LED backlight, brightness 350 Cd/m2
Power supply 15 to 30 Vdc
Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 Quad/Dual OpenFrame modules are "system on modules plus
openframe display carriers" which are good solution for develop
user friendly graphic user interface.
General features:
CPU NXP i.MX6Q rev1.2 at 792 MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
LVDS Display TFT 10.1" industrial, 1280x800 resolution
Backlight LED backlight, brightness 350 Cd/m2
Power supply 15 to 30 Vdc
Cc: Domenico Acri <domenico.acri@engicam.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx7d-sdb has a mickro bus connector that can be connected to a
Sensirion SHT11 click board (temperature and humidity sensor):
https://shop.mikroe.com/click/sensors/sht1x
Add a new device tree file to describe such hardware.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PHYs embedded in the switch direct there interrupts through the
switch interrupt controllers. Now that devel C has its switch
interrupts connected to the SoC, the PHY interrupts can be used by
phylib. Explicitly include MDIO nodes in the switch device tree nodes,
and link the PHY interrupts back to the switch interrupt
controller. Also, link the ports to the PHYs on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The devel B and devel C board use the same GPIO lines for interrupts
from the two switches. Move the pinmux nodes from devel B into the
shared .dtsi file, and wire up the interrupts on devel C.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UART on i.MX6SX (like all other i.MX6 SoC variants) has the same
programming model as the 'imx6q-uart' type, so add it to the compatible
UART string.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change the maxium spi clock frequency from 20MHz to 10MHz to meet the
operation voltage range requirement recommended in AT25 datasheet.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the reference manuals, both imx50/imx53 SOC seem to share
the same eSDHC controller, especially the section on "Multi-block Read"
mentioned in commit 361b848202 ("mmc: sdhci-esdhc-imx: fix multiblock
reads on i.MX53") is identical for both SOC.
Hence, let imx50 use imx53-esdhc.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reference them by handle and remove the changed clocks that are copied
from the downstream DT and are not part of the mainline binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Referencing the node by handle make the QP DT more resilent against
changes of the base DT. Also remove the duplicated reg property, it's
not needed as it the same as in the base DT, just the compatible is
actually different.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By using the handle, we can avoid some duplication of the base DT
and so avoid any maintenance overhead in the QP DT if the referenced
node changes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All currently supported i.MX25-based machines use phy_type = "utmi" and
dr_mode = "otg". So this seems to be a sensible default.
This also doesn't hurt out-of-tree machines because up to now they had
to specify these two properties in the machine.dts which still takes
precedence by just overwriting the defaults added here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and is sold as part
of I2SE's PLC Bundle for IoT. This is a development kit for Homeplug
Green PHY based powerline products based on Qualcomms QCA7000 chip.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and features a
EnOcean daugther board based on the popular TCM310 chipset.
This product is intended to be used for e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is based on I2SE's Duckbill 2 board and features a
RS-485 daugther board. This device is intended to be used for
e.g. home automation purposes.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This machine is an USB pen drive sized development board,
based on NXP's i.MX28 CPU. In contrast to the previous
model "Duckbill", the "Duckbill 2" series has internal
eMMC storage.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two fixes for the recent A33 cpufreq support, and one to fix a missing
register in the A64 USB PHY node.
-----BEGIN PGP SIGNATURE-----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=lFNZ
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.11, bis
Two fixes for the recent A33 cpufreq support, and one to fix a missing
register in the A64 USB PHY node.
* tag 'sunxi-fixes-for-4.11-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
Signed-off-by: Olof Johansson <olof@lixom.net>
The clocksource and the sched_clock provided by the arm_global_timer
are quite unstable because their rates depend on the cpu frequency.
On the other side, the arm_global_timer has a higher rating than the
rockchip_timer, it will be selected by default by the time framework
while we want to use the stable rockchip clocksource.
Let's disable the arm_global_timer in order to have the rockchip
clocksource selected by default.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
The patch add two timers to all rk3188 based boards.
The first timer is from alive subsystem and it act as a backup
for the local timers at sleep time. It act the same as other
SoC rockchip timers already present in kernel.
The second timer is from CPU subsystem and act as replacement
for the arm-global-timer clocksource and sched clock. It run
at stable frequency 24MHz.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Property set to '"rockchip,rk3228-timer", "rockchip,rk3288-timer"'
to match devicetree bindings.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Suggested-by: Heiko Stübner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Romulus has a RS-232 connection on the back of chassis, add UART1 to use
this connection.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The string was changed when upstreaming the driver. Put the correct
string for generation 4 and 5 systems, as well as fix the reg length for
ast2500 systems.
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
All chips on OpenPOWER platforms support the fastread SPI command.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Romulus systems have one MX25L25635 (32768 Kbytes) flash module for
the BMC firmware and other MT25QL512A (65536 Kbytes) for the host.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We do not yet have a clk driver upstream. So that users can boot the
unmodified upstream kernel, add fixed-clock and clock-frequency
properties to all of the clocks.
The values are taken from the Palmetto system. This is the only upstream
dts. It also happens to match all of the systems seen so far.
Acked-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We do not yet have a clk driver upstream. So that users can boot the
unmodified upstream kernel, add fixed-clock and clock-frequency
properties to all of the clocks.
The values are taken from the ast2500evb. This is the only upstream dts.
It also happens to match all of the systems I have seen so far.
Acked-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This reverts commit 769907ae6e.
This change caused issues with people using USB gadget for serial
consoles. In addition, with the other USB changes coming in, it
makes sense to revert this patch and apply the new set as it
becomes ready.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Following interfaces and devices are available on the PCM-947 carrier board:
- 2x UART
- micro SDMMC
- USB host and USB otg
- USB 3503 HSIC hub
- Ethernet
- 2nd alternative KSZ9031 ethernet phy
- Display connectors: PHYTEC LVDS, DDG LVDS, parallel signals, HDMI
- Parallel Camera CIF
- SGTL5000-32QFN audio codec
- 4x LEDs connected via PCA9533
- 2 user buttons
- Expansion connectors for WiFi and other modules
- RTC RV-4162-C7
- Resistive touch STMPE811
- EEPROM M24C32
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The current practice is to not add _clk suffixes to clock node names in
DT, as these names are used as the actual clock names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The current practice is to not add _clk suffixes to clock node names in
DT, as these names are used as the actual clock names.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the 32.768 kHz RTC_X1 clock by setting the frequency value to
non-zero and enable the realtime clock.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit a4ee7e18d8 ("ARM: dts: armada: Add default trigger for sata
led") adds the default trigger to individual boards, move it to
armada-385-linksys.dtsi which effectively enables the definition for
the WRT1900ACS (Shelby) as well as for future boards.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add CRC (CRC32 crypto) support to stm32f746.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The A33 supports 1.1GHz and 1.2GHz frequencies at 1.32V and the Sinlinx
SinA33 has its cpu-supply property set in the cpu DT node.
Therefore, CPUfreq knows how to handle the regulator in charge of the
CPU and can adjust its voltage to match the OPP.
Add these two CPU frequencies to the CPU OPP table of the Sinlinx
SinA33.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds GPU thermal throttling for the Allwinner A33.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
This adds CPU thermal throttling for the Allwinner A33. It uses the
thermal sensor present in the SoC's GPADC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the DT node for the thermal sensor present in the Allwinner
A33 GPADC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch changes the device node position of ps20 and ps21 to fix
ordering by rising physical address.
From
uart7: serial@01c29c00
i2c0: i2c@01c2ac00
i2c1: i2c@01c2b000
i2c2: i2c@01c2b400
ps20: ps2@01c2a000
ps21: ps2@01c2a400
to
uart7: serial@01c29c00
ps20: ps2@01c2a000
ps21: ps2@01c2a400
i2c0: i2c@01c2ac00
i2c1: i2c@01c2b000
i2c2: i2c@01c2b400
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the 32.768 kHz RTC_X1 clock by setting the frequency value to
non-zero.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the RTC clocks to device tree. The frequencies must be fixed values
according to the hardware manual.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The X2 crystal oscillator on the Koelsch development board provides a
74.25 MHz clock, not a 148.5 MHz clock.
Fixes: cd21cb46e1 ("ARM: shmobile: koelsch: Add DU external pixel clocks to DT")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
I disabled SRAM and GPMC originally when seeing errors with
omap_barriers_init(). But that is no longer happening probably
because the memory range is now properly configured to 1021 MB
instead of 1024 MB. So let's enable SRAM and GPMC so we get
omap_barriers_init() working and can idle the GPMC.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CPCAP PMIC interrupt is level high sensitive despite it being
requested as edge high triggered in the Motorola Linux kernel.
Note that also the related driver change is needed posted as
"mfd: cpcap: Fix interrupt to use level interrupt".
Fixes: 56e1d40d3b ("mfd: cpcap: Add minimal support")
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the 2 ethernet ports as CPSW ports in dual-mac mode
Signed-off-by: Roger Quadros <rogerq@ti.com>
[nsekhar@ti.com: use AM33XX_IOPAD()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM571x IDK and the AM572x IDK use CAN1 interface.
This patch enables it for both boards.
Tested on AM572x IDK using cansequence.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[nsekhar@ti.com: move to use DRA7XX_CORE_IOPAD())
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now we have driver for the PRCM CCU, switch to use it instead of
old-style clock nodes for apb0-related clocks in sunxi-h3-h5.dtsi .
The mux 3 of R_CCU is still the internal oscillator, which is said to be
16MHz plus minus 30%, and get a measured value of 15MHz~16MHz on my two
H3 boards and one H5 board.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 SoC has an on-board CAN controller. This patch adds
the pinctrl settings for pins PH20 and PH21.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20 SoC has an on-board CAN controller.
This patch adds the device node.
The CAN controller is inherited from the A10 SoC and uses the same driver.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10 SoC has an on-board CAN controller. This patch adds the
pinctrl settings for pins PH20 and PH21.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A10 SoC has an on-board CAN controller.
This patch adds the device node.
This patch is adapted from the description in
Documentation/devicetree/bindings/net/can/sun4i_can.txt
Signed-off-by: Patrick Menschel <menschel.p@posteo.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubietruck has an AXP209 PMIC and can be power-supplied by ACIN via
the CHG-IN pin or by USB.
This enables the ACIN and the USB power supply subnode in the DT.
Signed-off-by: Alexander Syring <alex@asyring.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the Z2 clock (Cortex-A7 CPU core clock), which uses a fixed divider,
and link the first CPU node to it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Unlike other R-Car Gen2 SoCs with Cortex-A15 CPU cores, R-Car V2H does
not have a programmable Z clock (Cortex-A15 CPU core clock), but uses a
fixed divider.
This is similar to the Z2 clock (Cortex-A7 CPU core clock) on R-Car E2.
Hence:
- Remove the Z clock output from the cpg_clocks node, as this implied
a programmable clock,
- Add the Z clock as a fixed factor clock,
- Let the first CPU node point to the new Z clock,
- Remove the Z clock index from the bindings (this definition was used
by r8a7792.dtsi only, and was not a contract between DT and driver).
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: 072d326542 ("ARM: dts: r8a7793: add MSTP10 clocks to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: ee9141522d ("ARM: shmobile: r8a7791: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SSI-ALL gate clock is located in between the P clock and the
individual SSI[0-9] clocks, hence the former should be listed as their
parent.
Fixes: bcde372254 ("ARM: shmobile: r8a7790: add MSTP10 support on DTSI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Technically, the Ethernet block is run off the 133MHz Bus (B) clock, not
the 33MHz Peripheral 0 (P0) clock.
Fixes: 969244f9c7 ("ARM: dts: r7s72100: add ethernet clock to device tree")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables USB HS working in FS mode on stm32f429-disco
with 5V VBUS enable.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch enables USB FS on stm32f469-disco with 5V VBUS enable.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds the USB pins and nodes for USB FS core.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Update the Alpine clock-frequency values with valid default values. The
bootloader can still update these values if needed, but at least we can
boot if it does not.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Cosmetic cleanup to have consistent node definitions. Add a space before
the node units which do not have one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
At this time, most of changes are for ASoC, while we got one fix for
yet another race of ALSA sequencer core and a usual HD-audio quirk.
The ASoC changes are mostly small and device-specific fixes. A
slightly large volume is seen in sun8i-codec, which is a new code in
4.11, and we'd like to fix user-visible stuff before the official 4.1
release.
-----BEGIN PGP SIGNATURE-----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=qutY
-----END PGP SIGNATURE-----
Merge tag 'sound-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"At this time, most of changes are for ASoC, while we got one fix for
yet another race of ALSA sequencer core and a usual HD-audio quirk.
The ASoC changes are mostly small and device-specific fixes. A
slightly large volume is seen in sun8i-codec, which is a new code in
4.11, and we'd like to fix user-visible stuff before the official 4.1
release"
* tag 'sound-4.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ALSA: hda - fix a problem for lineout on a Dell AIO machine
ASoC: simple-card: fix simple_dai clk lookup
ASoC: STI: Fix reader substream pointer set
ALSA: seq: Fix race during FIFO resize
ARM: dts: sun8i: Update audio-routing with renamed widgets
ASoC: sun8i-codec: Convert to use SND_SOC_DAPM_AIF_IN
ASoC: sun8i-codec: Fix space on audio-routing widget
ASoC: sun8i-codec: Update mixer to use SOC_DAPM_DOUBLE
ASoC: sun8i-codec: Remove analog "HP" widget
ASoC: rt5665: fix wrong shift rt5665_if2_1_adc_in_enum
ASoC: rt5665: fix define of RT5665_HP_DRIVER_5X
ASoC: rcar: dma: remove unnecessary "volatile"
ASoC: rcar: clear DE bit only in PDMACHCR when it stops
ASoC: rsnd: fix sound route path when using SRC6/SRC9
ASoC: don't dereference NULL pcm_{new,free}
ASoC: rt5665: CLKDET is also a power of ASRC
ASoC: rt5665: Vref3 is necessary for Mono Amp
ASoC: rt5665: increase LDO level
ASoC: rt5665: fix getting wrong work handler container
ASoC: atmel-classd: fix audio clock rate
...
There was a little conflict between the v4.11 bugfixes and the new changes for 4.12,
this merges the fixes into the 4.12 branch to avoid having to resolve it again.
* Broadcom fixes in mainline
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: BCM5301X: Fix memory start address
ARM: dts: BCM5301X: Fix UARTs on bcm953012k
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add hecc node for am35x
- Add onenand support for omap3-igep
- Add bluetooth binding for n900/n9/n950
- Configure clocks and SATA for dm81xx
- Update operating points tables for am33xx, am43xx and dra7
- Update SPI flash documentation for w25q64
- Configure SPI NOR for am335x-icev2
- Mux uart0 for am437x-gp-evm
- Add thermal zones for omap3, omap4, omap5, dra7
- Configure LEDs for am335x-baltos
- A series of droid 4 changes to configure various devices
such as keypad, regulators, gpio-keys, rtc, power button,
compass, accelerometer, touchscreen, backlight, poweroff,
tmp105, HDMI, LCD panel and LEDs, EHCI, and micro-SD
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlja1soRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXPS9hAAsFKL0gkbNG+u0P12y73IShSgt0Xhffmq
ChwdxMsRrPi5IJEOyPjcn3/HzWibBb/v+do1LIIM9i8Q+PchX+6DgssTYZEq5CAZ
szMvwNfqrT2AmV2iwM4u6xOaM+hAY9RoAtYikQpJ8Wm6vH9Dgy1Ve4ge2NmKna6P
0wnRJHIBJOzfGq4cP75QXqy2m/LJ4wwmP8pVzVa/9l/XtFlrsNT7n/kQ203PgYtR
k/nkr/Z3XEyY/nCaKosUbHS6o+CCMcxpdF2RjWcrlqvHg4xdm8eB+ilJh3be0eWH
7NMakynGXuqiI5lCqLeOpkBftD/kqSTojYuSY11nOhT+hHtoRe+KbOWYTf5UK7vb
rGXERxoZYm0WVtePDPAb+cyc7XdPTmqkXMJwCBKfomcndgcSQJqYgeUv380+5blF
76rhOq3xiKEDOPly8tjDS+4saZ+zEHj6dINhu+Lv56uQJCm0Y7o0j/RO4KMmZYAv
Ht71lOM7xNEAhw/Opk03A1ERkQNDuK1lmjW4M5hmHDskboB0RLOnGBLDDvWBIH/Q
H129hbDyEjEgMqgTuZi3cEt83jvQ0clzwjnmDDBW9O/nk1OpUHzPD4MMELNo+hBR
g1BOKjAQ6nwN3yV9i+eyiY+nk822Hu1L5CpXXDrP0XZlVOhGFbSS+6/uCztfBhcl
p7uZtAidu68=
=CRcK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/dt-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Devicetree changes for omaps for v4.12 merge window" from Tony Lindgren:
- Add hecc node for am35x
- Add onenand support for omap3-igep
- Add bluetooth binding for n900/n9/n950
- Configure clocks and SATA for dm81xx
- Update operating points tables for am33xx, am43xx and dra7
- Update SPI flash documentation for w25q64
- Configure SPI NOR for am335x-icev2
- Mux uart0 for am437x-gp-evm
- Add thermal zones for omap3, omap4, omap5, dra7
- Configure LEDs for am335x-baltos
- A series of droid 4 changes to configure various devices
such as keypad, regulators, gpio-keys, rtc, power button,
compass, accelerometer, touchscreen, backlight, poweroff,
tmp105, HDMI, LCD panel and LEDs, EHCI, and micro-SD
* tag 'omap-for-v4.12/dt-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
ARM: dts: am335x-baltos: add LED support
ARM: dts: omap4-droid4: Fix MMC1 card for detect GPIO and regulator
ARM: dts: OMAP4460: Thermal: Add slope and offset values
ARM: dts: OMAP443x: Thermal: Add slope and offset values
ARM: dts: OMAP5: Thermal: Add slope and offset values
ARM: dts: DRA7: Thermal: Add slope and offset values
ARM: dts: omap3: Add cpu_thermal zone
ARM: dts: am437x-gp-evm: Add pinmux for uart0
ARM: dts: am335x-icev2: Add SPI based NOR
Documentation: devicetree: mtd: add w25q64 to list of supported SPI flashes
ARM: dts: dra7: Add updated operating-points-v2 table for cpu
ARM: dts: am4372: Update operating-points-v2 table for cpu
ARM: dts: am335x-boneblack: Enable 1GHz OPP for cpu
ARM: dts: am33xx: Add updated operating-points-v2 table for cpu
ARM: dts: dm8168-evm: add SATA node
ARM: dts: dm8168-evm: add the external reference clock for SATA
ARM: dts: N9/N950: add bluetooth
ARM: dts: N900: Add bluetooth
ARM: dts: omap4-droid4: Configure EHCI so modems can be accessed
ARM: dts: motorola-cpcap-mapphone: add LEDs
...
definitions for the mmc resets in the socs reset controller, sound
support for the Rock2, dma support for mmc controllers on the rk3188
and a led-fix for the MiQi board and and irq-fix for older Cortex-A9 socs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAljY6NUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgTORB/49/3AhQ9neAjN5igVGMxv2PX5OPkYz07wJ
AgPPyUDBchXIU2teAuPzv/T9rS0wAJR58qLL7JiYjYz+II/XE3qWJUjiT5p5mjsp
ko4ijesWraf5C7z2ltL0T25lIyZwkjCJgjMzIxLMOsDgF4nN1yBxYh18CXXyc3sL
G3GYVGwEAhM9EwFjzrpyL7guFe2ZiKAZ7QmVeLmsDT9goECgz1XebuM+3idbOwJB
JjhmOmiSuUAHZO6o3soOZiDzb6xD9MELp/5a6MAoyoBWfnzHFtvsGwD/npDBEFB8
7JP9z4tc+LgKlIjg3QWUU52FVm1vEKA8p7jMNLpZmlMkc7pNPjLf
=oPg4
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts32 updates for 4.12 part1" from Heiko Stübner:
Contains one new board, the Tinkerboard from Asus based on the rk3288,
definitions for the mmc resets in the socs reset controller, sound
support for the Rock2, dma support for mmc controllers on the rk3188
and a led-fix for the MiQi board and and irq-fix for older Cortex-A9 socs.
* tag 'v4.12-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: setup DMA-channels for mmc0 and emmc for rk3188
ARM: dts: rockchip: fix PPI misconfiguration on Cortex-A9 socs
ARM: dts: rockchip: add rk322x dw-mmc resets
ARM: dts: rockchip: add rk3066/rk3188 dw-mmc resets
ARM: dts: rockchip: add rk3036 dw-mmc resets
ARM: dts: rockchip: add rk3288 dw-mmc resets
ARM: dts: rockchip: add dts for RK3288-Tinker board
dt-bindings: add rk3288-based Asus Tinker board
ARM: dts: rockchip: fix the MiQi board's LED definition
ARM: dts: rockchip: Add support for ES8388 to the Radxa Rock 2
- Add the power controller to the DTS.
- Augment the GPIO nodes to also include the Faraday
compatible.
- Add the PCI bus host and config to the Gemini device trees.
-----BEGIN PGP SIGNATURE-----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=AkSm
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "DTS updates for the Gemini on top of the multiplatform base" from Linus Walleij:
- Add the power controller to the DTS.
- Augment the GPIO nodes to also include the Faraday
compatible.
- Add the PCI bus host and config to the Gemini device trees.
* tag 'gemini-dts-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: add PCI to the Gemini device trees
ARM: dts: augment Gemini GPIO nodes
ARM: dts: add power controller to the Gemini DTS
4.12, please pull the following:
- Rafal:
* adds basic support for the Linksys EA9200, Linksys EA6300 V1, Linksys
EA9500, TP-Link Archer C5 V2 which are all based on BCM470x SoCs with
a bunch of BCM43602 radios.
* updates the BCM5301X DTS and DTS include file and moves the serial
console parameters to the DTS include file since all BCM5301X that we have so
far are consistent in using the same UART. He also does the same for the
BCM53573 DTS.
* makes some updates to the Tenda AC9 platform by describing its
PCIe controllers and endpoints in order to be able to represent GPIOs attached
to the on-chip Wi-Fi module. Once done, he adds the 2Ghz LED which is connected
to one of these GPIOs.
* re-licenses the DTS files he created to the ISC license
* removes the use of the non-existend "default-off" LED trigger in the
BCM53573 and BCM5301X DTS files
- Aditya adds missing Netgear R8000 LEDS and keys for WAN status LEDS and brightness
- Jon:
* adds NAND controller Device Tree nodes to the BCM953012K reference board
* converts the BCM5301X SoC to use the recently introduced Broadcom QSPI controller
Device Tree nodes.
* fixes the GIC PPI interrupt flags that the kernel now
reports about.
* adds ARM TWD watchdog entries to the BCM5301X DTS include file
* adds I2C entries to the BCM5301X DTS include files.
* disables i2c by default in the Northstar Plus DTS include file, and
,enables it at the board level instead.
* adds USB (OHCI & EHCI) Device Tree nodes to the Northstar Plus DTS
include files.
- Steven adds the mailbox (PDC) unit and the crytographic unit (SPU) to the
Broadcom Northstar Plus SoC DTS include file. Steven also adds proper ethernet
aliases to the BCM53012HR board since some bootloaders require that for MAC address
patching.
- Eric adds the DSI and its corresponding clock nodes to the BCM283x DTS files
but leaves them disabled by default (overlays should take care of enabling it)
- Boris adds support for HDMI audio and related DMA channels to the BCM283x SoCs
- Gerd adds support for the BCM2835 specific SDHCI controller to the BCM283x SoCs
- Rob fixes the iProc msi-controller name and unit address now that DTC can produce
additional errors
-----BEGIN PGP SIGNATURE-----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=VFXn
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.12/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.12" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree updates for
4.12, please pull the following:
- Rafal:
* adds basic support for the Linksys EA9200, Linksys EA6300 V1, Linksys
EA9500, TP-Link Archer C5 V2 which are all based on BCM470x SoCs with
a bunch of BCM43602 radios.
* updates the BCM5301X DTS and DTS include file and moves the serial
console parameters to the DTS include file since all BCM5301X that we have so
far are consistent in using the same UART. He also does the same for the
BCM53573 DTS.
* makes some updates to the Tenda AC9 platform by describing its
PCIe controllers and endpoints in order to be able to represent GPIOs attached
to the on-chip Wi-Fi module. Once done, he adds the 2Ghz LED which is connected
to one of these GPIOs.
* re-licenses the DTS files he created to the ISC license
* removes the use of the non-existend "default-off" LED trigger in the
BCM53573 and BCM5301X DTS files
- Aditya adds missing Netgear R8000 LEDS and keys for WAN status LEDS and brightness
- Jon:
* adds NAND controller Device Tree nodes to the BCM953012K reference board
* converts the BCM5301X SoC to use the recently introduced Broadcom QSPI controller
Device Tree nodes.
* fixes the GIC PPI interrupt flags that the kernel now
reports about.
* adds ARM TWD watchdog entries to the BCM5301X DTS include file
* adds I2C entries to the BCM5301X DTS include files.
* disables i2c by default in the Northstar Plus DTS include file, and
,enables it at the board level instead.
* adds USB (OHCI & EHCI) Device Tree nodes to the Northstar Plus DTS
include files.
- Steven adds the mailbox (PDC) unit and the crytographic unit (SPU) to the
Broadcom Northstar Plus SoC DTS include file. Steven also adds proper ethernet
aliases to the BCM53012HR board since some bootloaders require that for MAC address
patching.
- Eric adds the DSI and its corresponding clock nodes to the BCM283x DTS files
but leaves them disabled by default (overlays should take care of enabling it)
- Boris adds support for HDMI audio and related DMA channels to the BCM283x SoCs
- Gerd adds support for the BCM2835 specific SDHCI controller to the BCM283x SoCs
- Rob fixes the iProc msi-controller name and unit address now that DTC can produce
additional errors
* tag 'arm-soc/for-4.12/devicetree' of http://github.com/Broadcom/stblinux: (27 commits)
ARM: dts: bcm: fix msi-controller name and unit address
ARM: dts: BCM53573: Specify serial console parameters
ARM: dts: BCM5301X: Specify serial console params in dtsi files
ARM: dts: NSP: Add crypto (SPU) to dtsi
ARM: dts: NSP: Add mailbox (PDC) to NSP
ARM: dts: BCM953012HR: Add ethernet aliases
ARM: dts: BCM5301X: Add support for TP-LINK Archer C5 V2
ARM: dts: NSP: disable i2c DT entry by default
ARM: dts: NSP: Add EHCI/OHCI USB nodes to device tree
ARM: dts: BCM5301X: Add I2C support to the DT
ARM: dts: BCM5301X: Add TWD WD Support to DT
ARM: dts: BCM5301X: Correct GIC_PPI interrupt flags
ARM: dts: bcm2835: add sdhost controller to devicetree
ARM: dts: bcm283x: Add HDMI audio related properties
ARM: dts: BCM5301X: Don't use nonexistent "default-off" LED trigger
ARM: dts: BCM53573: Don't use nonexistent "default-off" LED trigger
ARM: dts: BCM5301X: Add missing Netgear R8000 LEDs and Keys
ARM: dts: BCM5301X: Relicense DTS files I created to the ISC
ARM: dts: bcm2835: Add the DSI module nodes and clocks.
ARM: dts: BCM53573: Add Tenda AC9 2 GHz LED
...
- Add node lable for Armada 38x
- Add support for Synology DS116 NAS and Linksys WRT1900ACS
- Update mbus controller description on Armada 38x allowing entering in standby
- Add default trigger for sata led on various linksys boards
- Update newly added armada-xp-98dx3236
- Enable hardware buffer manager support for the devices in the
Linksys WRT AC Serie
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWNVVVyMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71f1XAJ0WIMcrTJPA
uiYAEbN2f+InledW9wCeOD5+hJTSEFFznZSfbzN4Morh0tw=
=+cen
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.12-1' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt for 4.12 (part 1)" from Gregory CLEMENT:
- Add node lable for Armada 38x
- Add support for Synology DS116 NAS and Linksys WRT1900ACS
- Update mbus controller description on Armada 38x allowing entering in standby
- Add default trigger for sata led on various linksys boards
- Update newly added armada-xp-98dx3236
- Enable hardware buffer manager support for the devices in the
Linksys WRT AC Serie
* tag 'mvebu-dt-4.12-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: linksys: enable buffer manager support
ARM: dts: mvebu: remove unnecessary PCI range from 98dx3236
ARM: dts: mvebu: Move mv98dx3236 clock bindings
ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236
ARM: dts: armada-xp-98dx3236: combine dfx server nodes
ARM: dts: armada: Add default trigger for sata led
ARM: dts: armada-38x: Adjust mbus controller description on Armada 38x
ARM: dts: armada-385: add support for the Linksys WRT1900ACS (Shelby)
ARM: dts: armada-385-synology-ds116: add support for Synology DS116 NAS
ARM: dts: armada-38x add node labels
Video display on DA850 along with some
whitespace clean-up.
Also, enables sound and ADC support on
Lego EV3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DFR4
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.12/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Pull "DaVinci DT updates for v4.12" from Sekhar Nori:
DaVinci device tree updates to enable
Video display on DA850 along with some
whitespace clean-up.
Also, enables sound and ADC support on
Lego EV3.
* tag 'davinci-for-v4.12/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: add the output port to the vpif node
ARM: dts: da850-evm: add IO expander node on UI card
ARM: dts: da850: add vpif video display pins
ARM: dts: da850-evm: fix whitespace errors
ARM: da850-lego-ev3: Add device tree node for sound
ARM: da850-lego-ev3: Add device tree node for A/DC
The Moxa ART GPIO is a Faraday FTGPIO010. Augment the DTS node
to indicate both compatible values for the SoC and the IP part.
Also increase the register range to 0x100, it has at least 0x48
bytes of registers, and a few extra will not hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the new hdmi phandle to exynos4.dtsi. This phandle is needed by the
s5p-cec driver to initialize the CEC notifier framework.
Tested with my Odroid U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Keep the clearfog DTS file ordered alphabetically - Florian placed the
MDIO entry after pinctrl, which mis-orders the file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This moves the spi0_cs3_pin pinconf node from the LEGO EV3 file to the
common DA850 include file. This node is applicable to any board, and
therefore belongs in the common file.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The two st231-rproc nodes have the same name; Due to that it was
impossible to distinguish them in remoteproc sysfs and debugfs
interface.
This patch provides them a name related to their functionality.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
The display backend on sun5i shares the same interrupt line as the
display frontend. Add it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the RPM Clock Controller DT node for msm8974-based platforms, so that
drivers can use the clocks provided by the RPM processor.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The DTS referred to SDC5 when it meant SDC1.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
To make the picture complete, add DTS entries also for the
second and fourth MMC/SD blocks on the MSM8660. SDC2 is
an 8-bit interface and SDC4 is a 4-bit interface.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Without this patch (and with CONFIG_QCOM_ADSP_PIL), I get this error:
[ 0.711529] qcom_adsp_pil adsp-pil: failed to get xo clock
[ 0.711540] remoteproc remoteproc0: releasing adsp-pil
With this patch, adsp-pil can initialize correctly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial set of CoreSight components found on Qualcomm
msm8974 and apq8074 based platforms, including the APQ8074
Dragonboard board.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Rock 2 square board has a USB -> SATA converter hooked up to its usb
host1 connection. Enable the usb controller and always turn on the power
on the 5V sata power connector (controlled by gpio).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All three devices provide GPIO based LEDs named power,
wlan and app.
Place LEDs definition into a separate dtsi file as not all
devices including am335x-baltos.dtsi have the same LED layout.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a typo, it should be GPIO176 and not GPIO106.
And it seems I messed up the regulators at some point while trying
to figure out what devices the regulators are used. The correct
regulator for MMC1 is vwlan2.
Fixes: 0d4cb3ccee ("ARM: dts: Configure regulators for droid 4")
Reported-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 84e734f497 ("ARM: dts: silk: add DU DT support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 876e7fb9f4 ("ARM: shmobile: r8a7794: alt: Enable VGA port")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The second channel of the display unit uses a different module clock
than the first channel.
Fixes: 46c4f13d04 ("ARM: shmobile: r8a7794: Add DU node to device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the missing module clock for the second channel of the display unit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
An alias name should have an index number even when it is the only of its type.
This allows U-Boot to add the local-mac-address property. Otherwise U-Boot
skips the alias.
Fixes: 6a93792774 ("ARM: bcm2835: dt: Add the ethernet to the device trees")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document uart1 doesn't map to pins
36-39, but uart0 does.
Also, split into separate Rx/Tx and CST/RTS groups to match other uart nodes.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the BCM2835 ARM Peripherals document i2c0 doesn't map to pins 32,
34 but to 28, 29.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
Downstream kernel uses pins 32, 33 as UART0 (PL011) Rx/Tx to communicate with
the Bluetooth chip. So ALT3 of these pins is most likely not CTS/RTS. Change
the node name to reflect that. This matches section 6.2 "Alternative Function
Assignments" in the BCM2835 ARM Peripherals document.
With this change in place, adding
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
};
to bcm2837-rpi-3-b.dts does the right thing on my Raspberry Pi 3.
Pins 30, 31 are CTS/RTS of UART0 in alternate function 3. Rename uart0_gpio30
as well.
While at it, fix a little typo in a nearby comment.
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Eric Anholt <eric@anholt.net>
mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Orange Pi Zero board features a USB OTG port, which has a ID pin, and
can be used to power up the board. However, even if the board is powered
via +5V pin in GPIO/expansion headers, the VBUS in the OTG port cannot
be powered up, thus it's impossible to use it in host mode with simple
OTG cables.
Add support for it in peripheral mode.
If someone really want to use it in host mode, the mode of PHY can be
switch via sysfs, then use a powered USB OTG cable or powered USB HUB to
power up external USB devices.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi One features a MicroUSB port that can work in both host mode
and peripheral mode.
When in host mode, its VBUS is controlled via a GPIO; when in peripheral
mode, its VBUS cannot be used to power up the board.
Add support for this port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H3/H5 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Add device nodes for these controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a seperated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit makes use of the axp209.dtsi file to define the
AXP209 PMIC. While here, define the rails that are enabled on
this board.
Tested checking the regulator voltage varies according to the
CPU frequency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA31s has a coaxial SPDIF output. Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the cpu-supply DT property to the cpu0 DT node needed by
the board to adapt the regulator voltage depending on the currently used
OPP.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds almost all operating points allowed for the A33 as defined by
fex files available at:
https://github.com/linux-sunxi/sunxi-boards/tree/master/sys_config/a33
There are more possible frequencies in this patch than there are in the
fex files because the fex files only give an interval of possible
frequencies for a given voltage. All supported frequencies are defined
in the original driver code in Allwinner vendor tree.
There are two missing frequencies though: 1104MHz and 1200MHz which
require the CPU to have 1.32V supplied, which is higher than the default
voltage.
Without all A33 boards defining the CPU regulator, we cannot have these
two frequencies as it would cause the CPU to try to run a higher
frequency without "overvolting" which is very likely to crash the CPU.
Therefore, these two frequencies must be enabled on a per-board basis.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NextThing Co. CHIP has an AXP209 PMIC and can be power-supplied by
ACIN via the CHG-IN pin.
This enables the ACIN power supply subnode in the DT.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx SinA33 has an AXP223 PMIC and an ACIN connector, thus, we
enable the ACIN power supply in its Device Tree.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP22X PMIC exposes the status of AC power supply.
This adds the AC power supply subnode for the AXP22X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The X-Powers AXP20X PMIC exposes the status of AC power supply, the
current current and voltage supplied to the board by the AC power
supply.
This adds the AC power supply subnode for AXP20X PMIC.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm/boot/dts/sun?i*.*
arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The old sunxi specific pinctrl bindings are deprecated, in favor of
the new generic pinconf bindings. Also, we are moving towards handling
GPIO pinmux settings that don't require extra bias or drive strength
settings to use the GPIO bindings only.
This patch removes the last instance of the sunxi specific pinctrl
bindings that use the pinctrl header by dropping the pinmux setting
for the audio codec's PA (external amplifier) control GPIO. The pin
is pulled down externally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PCIe bridges should have a node name of 'pcie'.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
The Cortina Gemini has an internal PCI root bus, add this to
the device tree, and add interrupt mapping (swizzling) to the
relevant systems device trees.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
-----BEGIN PGP SIGNATURE-----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=bTSQ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=cLA3
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2017-03-21' into devicetree/next
This pull request brings in the DT nodes for enabling HDMI audio on
Raspberry Pi, and nodes to describe the DSI and SDHOST hardware
modules (which are still disabled by default).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=CKev
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux into fixes
Pull "Broadcom arm Device Tree fixes for 4.11 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.11,
please pull the following:
- Jon fixes a reboot issue on most Northstar Plus platforms by adding the
"open-source" property to the "gpio-restart" Device Tree nodes
* tag 'arm-soc/for-4.11/devicetree-fixes-2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: GPIO reboot open-source
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the slope and offset values for calculating the
hot spot temperature of a particular thermal zone is part
of driver data. Pass them here instead and obtain the values
while of node parsing.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for STM32H743 MCU and his eval board.
The STMicrolectornics's STM32H743 MCU is based on Cortex-M7 core
running up to @400MHz with 2MB internal flash and 1MB internal RAM.
For more details see:
Documentation/arm/stm32/stm32h743-overview.txt
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add pinmux for rx,tx,cts and rts lines of uart0. This will enable uart0
to use hardware flow control.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for W25Q64CVSSIG which is a Winbond 64 Mbit SPI NOR.
At boot you will see the following message:
m25p80 spi1.0: found s25fl064k, expected w25q64
This is because the JEDEC ID for this chip is the same as s25fl064k.
However, this should be harmless since both chips are essentially the
same.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in dra7.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
As we now need to define voltage ranges for each OPP, we define the
minimum and maximum voltage to match the ranges possible for AVS class0
voltage as defined by the DRA7/AM57 Data Manual, with the exception of
using a range for OPP_OD based on historical data to ensure that SoCs
from older lots still continue to boot, even though more optimal voltages
are now the standard. Once an AVS Class0 driver is in place it will be
possible for these OPP voltages to be adjusted to any voltage within the
provided range.
Information from SPRS953, Revised December 2015.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although all PG2.0 silicon may not support 1GHz OPP for the MPU, older
Beaglebone Blacks may have PG2.0 silicon populated and these particular
parts are guaranteed to support the OPP, so enable it for PG2.0 on
am335x-boneblack only.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After the ti-cpufreq driver has been added, we can now drop the
operating-points table present in am33xx.dtsi for the cpu and add an
operating-points-v2 table with all OPPs available for all silicon
revisions. Also add necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime as part of the operating-points
table.
Information from AM335x Data Manual, SPRS717i, Revised December 2015,
Table 5-7.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
eviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the SATA controller node to the dm8168-evm device tree.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This board has an external oscillator supplying the reference clock
signal for SATA. Its rate is fixed at 100Mhz. Add a corresponding
device tree node.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jagan Teki