Add initial support for PWM outputs of the PC87427 Super-I/O chip.
Only mode change and manual fan speed control are supported. Automatic
mode configuration isn't supported, and won't be until at least one
board is known, which makes uses of the PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for W83667HG-B (very similar to the W83667HG).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC's EMC2103 family of temperature/fan controllers have 1
onboard and up to 3 external temperature sensors, and allow
closed-loop control of one fan. This patch adds support for
them.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fault files are for hardware failures that can be reported. So far
we've seen chips reporting such failures for temperature sensors and
fans, but not for voltages. Remove in[0-*]_fault for now. It can be
added back later if really needed, but I doubt it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add currX_alarm, currX_min_alarm, currX_max_alarm and currX_beep
attributes to the hwmon sysfs API.
currX_min_alarm and currX_max_alarm are already supported by the LTC4215
and LTC4245 drivers. currX_alarm is supported by the LTC4261 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added _lcrit and _crit to voltage attributes.
Added _lcrit to temperature attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for exposing all GPIO pins as analog voltages. Though this is
not an ideal use of the chip, some hardware engineers may decide that the
LTC4245 meets their design requirements when studying the datasheet.
The GPIO pins are sampled in round-robin fashion, meaning that a slow
reader will see stale data. A userspace application can detect this,
because it will get -EAGAIN when reading from a sysfs file which contains
stale data.
Users can choose to use this feature on a per-chip basis by using either
platform data or the OF device tree (where applicable).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow device probing to recognise the Fintek F71808E.
Sysfs interface:
* Fan/pwm control is the same as for F71889FG
* Temperature and voltage sensor handling is largely the same as for
the F71889FG
- Has one temperature sensor less (doesn't have temp3)
- Misses one voltage sensor (doesn't have V6, thus in6_input refers to
what in7_input refers for F71889FG)
For the purpose of the sysfs interface fxxxx_in_temp_attr[] is split up
such that it can largely be reused.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update coretemp supported CPU TjMax lists and some cleanup work.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver adds support for the monitoring features of the Summit
Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Document for package level thermal hwmon driver.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1280448826-12004-6-git-send-email-fenghua.yu@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
pavel@suse.cz no longer works, replace it with working address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.
Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Add support for the hardware monitoring capabilities of the SCH5127
chip to the dme1737 driver.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Fixes from my driver review:
http://lists.lm-sensors.org/pipermail/lm-sensors/2010-March/028051.html
Only the small changes are in there, more important changes will come
later separately as time permits.
* Drop the remnants of the now gone detect function
* The TMP102 has no known compatible chip
* Include the right header files
* Clarify why byte swapping of register values is needed
* Strip resolution info bit from temperature register value
* Set cache lifetime to 1/3 second
* Don't arbitrarily reject limit values; clamp as needed
* Make limit writing unconditional
* Don't check for transaction types the driver doesn't use
* Properly check for error when setting configuration
* Report error on failed probe
* Make the driver load automatically where needed
* Various other minor fixes
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>
Driver for the TI TMP102.
The TI TMP102 is similar to the LM75. It differs from the LM75 by
having a 16-bit conf register and the temp registers have a minimum
resolution of 12 bits; the extended conf register can select 13-bit
resolution (which this driver does) and also change the update rate
(which this driver currently doesn't use).
[JD: Fix tmp102_exit tag, must be __exit, not __init.]
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The update_rate attribute can be used by drivers to let userspace choose
the update rate of the chip, if it is configurable.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM64 appears to be an LM63 with added GPIO lines. Add support for the
hwmon functionality - GPIO can be added at some later stage if someone
has a need for them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix obvious cases of "it's" being used when "its" was meant.
Signed-off-by: Francis Galiegue <fgaliegue@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
adt7473 driver is obsoleted by adt7475 driver. And it is scheduled
to be removed in Feb 2010.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Hwmon driver for Andigilog aSC7621 family monitoring chips.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add basic support for the ADT7411. Reads out all conversion results (via I2C,
SPI yet missing) and allows some on-the-fly configuration. Tested with a
custom board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Before switching to automatic fan control mode, make sure that all the
trip points make sense. Otherwise, the control loop could lead to
weird fan behavior.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the automatic fan speed control interface as
implemented by IT8705F chips up to revision F and IT8712F chips up to
revision G. This implementation fits very well in our standard sysfs
interface.
I implemented the old and not the new interface because the only chip
I have at hand is an old one, and the new interface is more difficult
to map to the standard sysfs interface. Adding support later should be
possible though, if someone with a supported chip is interested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Unfortunately ITE is no longer publicly providing datasheets for their
IT87xxF series of chips. They may send them on request if you ask
politely.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT87xxF chips support beeping on alarm, if properly wired and
configured. There is one control bit for each input type (temperature,
fan, voltage.) Let the user see and change them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested successfully with an ADM1032 chip on its evaluation board. It
should work fine with all other chips as well.
At this point this is more of a proof-of-concept, we don't do anything
terribly useful on SMBus alert: we simply log the event. But this could
later evolve into libsensors signaling so that user-space applications
can take an appropriate action.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
This chips is found on several Zotac Ion ITX boards, amongst others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: MC Matti <mcmatti17@googlemail.com>
Cc: Manuel Lamotte-Schubert <mls@pronego.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The latest version of the Revision Guide for AMD Family 10h Processors
lists two more processor revisions which may be affected by erratum 319.
Change the blacklisting code to correctly detect those processors, by
implementing AMD's recommended algorithm.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
This adds a driver for the internal temperature sensor of AMD Family 10h
and 11h CPUs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level. Add control of rate of change of fan output
level. These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority. Add
support for constant fan speed and proportional-response operations modes.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ADT7476 has 5 dedicated pins for VID input, and the +12V input can
optionally be used as a 6th VID pin. Add support for VID input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7476 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 5 voltage inputs instead of 2, and VID input
pins.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the Analog Devices ADT7490 chip. This chip is largely
compatible with the ADT7473 and ADT7475, with additional features.
In particular, it has 6 voltage inputs instead of 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
New documentation for the adt7475 driver, based on the adt7473 driver
documentation. It is IMHO much more useful that the previous
documentation which was essentially redundant with sysfs-interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Add support for the ADT7473 to the adt7475 driver, and mark the
adt7473 driver for removal. The ADT7473 and ADT7475 chips are almost
the same chip and essentially compatible, so there's no point in
having separate drivers for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
This adds support for the Fintek f71889fg to the f71882fg driver,
many thanks to Gerd v. Egidy for providing (remote) access to a
machine which such an ic.
Note that this bit of the patch:
- val = SENSORS_LIMIT(val, 0, 255);
+
+ if (data->type == f71889fg)
+ val = SENSORS_LIMIT(val, -128, 127);
+ else
+ val = SENSORS_LIMIT(val, 0, 127);
Changes behaviour for already supported models, the new behaviour is correct
as the already supported models have bit 7 of the involved registers fixed at
0, so the previous behaviour which allowed setting temp zone limits > 127
was not correct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver provides support for the ADC integrated into the
Freescale MC13783 PMIC.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This module parameter is there to workaround broken BIOS. I'm not even
sure if it was used in the past 5 years, and it gets in the way of
converting the driver to the MFD infrastructure. So tell the users how
they can do the same from user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@linux.it>
The VID input pins can alternatively be used as GPIOs. Make sure we
have at least 4 pins used for VID, otherwise don't bother reading and
exposing VID.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Adam Nielsen <a.nielsen@shikadi.net>
Document the case of hybrid automatic fan speed control
implementations, where trip points are associated to both PWM output
channels and temperature input channels.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Augment the documentation of the hwmon sysfs API to accomodate ACPI power
meters and the current desired behavior of power capping hardware drivers.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.
So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (ltc4245) Clear faults at startup
hwmon: (ltc4215) Clear faults at startup
hwmon: (coretemp) Add Lynnfield CPU
hwmon: (coretemp) Add support for Penryn mobile CPUs
hwmon: (coretemp) Fix Atom CPUs support
hwmon: Delete deprecated FSC drivers
hwmon: (adm1031) Add sysfs files for temperature offsets
Add Lynnfield processor support. Lynnfield is a quad-core Nehalem
based microprocessor for Desktop market, which is introduced in
September 2009.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Kent Liu <kent.liu@linux.intel.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Following patch adds support for mobile Penryn CPUs. Intel documents this
poorly. I asked the Coretemp author for some help. This is totally untested and
may not work. Please test!
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix Atom CPUs support. Intel documents TjMax at 90 degrees C but
some Atoms may have 125 degrees C (this is undocumented speculation).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@linux.intel.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy fscpos and fscher drivers have been replaced by the unified
fschmd driver. The transition period is over now, we can delete them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
Allows users who use an IDE driver for their disk to use hpfall without
having to modify the source. By default /dev/sda is used.
Suggested by Christian Thaeter in http://lkml.org/lkml/2009/3/25/505.
While we're add it, improve error message if opening /dev/freefall fails.
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Christian Thaeter <ct@pipapo.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Improve the example code to be at least useable, as in not causing
harm (as shown below). Code can still be improved further, but this
adds some basic safeguards.
1. hpfall *MUST* mlockall(MCL_CURRENT|MCL_FUTURE); itself!
Since the Program sits and waits most of the time it becomes very likely
swapped out. If it gets woken up when the laptop drops from the table
while it is swapped out it actually triggers harddrive activity!
2. Daemonize hpfall using 'daemon(0,0)' (quick and dirty).
3. Give hpfall realtime priority.
Should give a chance that it has less latency when woken up.
Signed-off-by: Christian Thaeter <ct@pipapo.org>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes hpfall.c conform to kernel coding style.
I have not fixed the C99 // comments on two lines as they
help indicate that those are not actually comments but
incomplete code.
Before:
total: 10 errors, 6 warnings, 101 lines checked
After:
total: 2 errors, 0 warnings, 99 lines checked
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver exposes ACPI 4.0 compliant power meters as hardware monitoring
devices. This second revision of the driver also exports the ACPI string
info as sysfs attributes, a list of the devices that the meter measures,
and will send ACPI notifications over the ACPI netlink socket. This
latest revision only enables the power capping controls if it can be
confirmed that the power cap can be enforced by the hardware and explains
how the notification interfaces work.
[akpm@linux-foundation.org: remove default-y]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver adds support for the hardware monitoring features of
the WM831x PMICs to the hwmon API. Monitoring is provided for
the system voltages supported natively by the WM831x, the chip
temperature, the battery temperature and the auxiliary inputs
of the WM831x.
Currently no alarms are supported, though digital comparators on
the WM831x devices would allow these to be provided.
Since the auxiliary and battery temperature input scaling depends
on the system configuration the value is reported as a voltage to
userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Clean up the pcf8591 driver documentation:
* The PCF8591 chip is now an NXP product.
* Fix a sysfs path.
* Fix the name of sysfs attributes.
* And a few other random fixes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Add documentation for the tmp421 driver.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the hwmon part of the Fintek F71858FG superio IC to the
f71882fg driver. Many thanks to Jelle de Jong for lending me a motherboard
with this superio on it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the new incarnation of the Winbond/Nuvoton W83627DHG
chip known as W83627DHG-P. It is basically the same as the original
W83627DHG with an additional automatic can speed control mode (not
supported by the driver yet.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Madhu <madhu.chinakonda@gmail.com>
Documentation for the tmp401 driver.
The documentation describes the tmp401 driver and the supported Texas
Instruments TMP401 and TMP411 temperature sensor chips.
Further documentation for new sysfs attributes supported by this
driver is added to Documentation/hwmon/sysfs-interface.
Signed-off-by: Andre Prendel <andre.prendel@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable auto-probing for the HC10 blade and amend the supported system
list.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add fan_max description.
Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Matthew Palmer <mpalmer@debian.org>
Signed-off-by: Laurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.
I have tested the driver with my board, and it appears to work fine. With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power. With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power. I'm not drawing any current at the
moment, so this is reasonable. The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.
I didn't attempt to support changing any of the chip's settings or
enabling the FET. I'm not sure even how to do that and still fit within
the hwmon framework. :)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix english in Documentation, add "how to test" description.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Cc: <Quoc.Pham@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define a standard interface for the chassis intrusion detection feature
some hardware monitoring chips have. Some drivers have custom sysfs
entries for it, but a standard interface would allow integration with
user-space (namely libsensors.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Matt Roberds <mattroberds@cox.net>
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.
If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.
At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* The alarms sysfs file is deprecated, and individual alarm files are
self-explanatory.
* The driver doesn't implement high-reslution temperature readings so
don't document that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Update documentation to prevent further confusion/duplication.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds freefall handling to hp_accel driver. According to HP, it
should just work, without us having to set the chip up by hand.
hpfall.c is example .c program that parks the disk when accelerometer
detects free fall. It should work; for now, it uses fixed 20seconds
protection period.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
hwmon: (abituguru3) Match partial DMI board name strings
hwmon: Add a driver for the ADT7475 hardware monitoring chip
hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
hwmon: (k8temp) Warn about fam F rev F errata
Fix lis3 documentation to fit into 80 columns.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hwmon driver for the ADT7475 chip.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (29 commits)
hwmon: Fix various typos
hwmon: Check for ACPI resource conflicts
hwmon: (lm70) Add TI TMP121 support
hwmon: (lm70) Code streamlining and cleanup
hwmon: Deprecate the fscher and fscpos drivers
hwmon: (fschmd) Add watchdog support
hwmon: (fschmd) Cleanups for watchdog support
hwmon: (i5k_amb) Load automatically on all 5000/5400 chipsets
hwmon: (it87) Add support for the ITE IT8720F
hwmon: Don't overuse I2C_CLIENT_MODULE_PARM
hwmon: Add LTC4245 driver
hwmon: (f71882fg) Fix fan_to/from_reg prototypes
hwmon: (f71882fg) Printout fan modes
hwmon: (f71882fg) Add documentation
hwmon: (f71882fg) Fix auto_channels_temp temp numbering with f8000
hwmon: (f71882fg) Add missing pwm3 attr for f71862fg
hwmon: (f71882fg) Add F8000 support
hwmon: (f71882fg) Remove the fan_mode module option
hwmon: (f71882fg) Separate max and crit alarm and beep
hwmon: (f71882fg) Check for hwmon powerdown state
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution. This patch extends the
LM70 driver to support the TMP121. The TMP123 differs in pin assign-
ment.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated. This in turn happens only when
someone tells the chip to read its temperature sensors. Regrettably, this
means that we have to drive the chip periodically.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New driver to play with. As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors. This driver has been tested on an IntelliStation Z30.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard"). It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.
This driver was first written by Yan Burman. Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now). Pavel Machek removed few more features and switched locking from
semaphore to mutex.
Several people have contributed to the database of the axes.
[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Add at least the bare minimum of documentation for this chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350
This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The lm87 driver normally assumes that firmware configured the chip
correctly. Since this is not always the case, alllow platform code to
set the channel register value via platform_data. All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
Describe the sysfs files that were introduced in the ibmaem driver.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.
The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dominik Geyer <dominik.geyer@gmx.de>
Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128,
and fixes a problem with incorrectly reported fan speeds.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Document the characteristics of libsensors 3.0.0 and 3.0.1.
* The sysfs interface is no longer subject to changes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This driver reads IBM Active Energy Manager energy/temperature/power
sensors on IBM System X hardware.
[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a sentence about when fan speed increases to maximum.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's nothing we can do about read errors on the W83L785TS-S, so
don't ask the user to report them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for family 0x17, which has Penryn Core. It should also
cover the 8 cores Xeons.
Can someone test please? I think it should work.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Following patch will add reporting of maximum temperature, at which all fans
should spin full speed. It may be non-physical temperature on Desktop/Server CPUs.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
While the W83627EHF/EHG has only 6 VID pins, the W83627DHG has 8 VID
pins, to support VRD 11.0. Add support for this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Steve Hardy <steve@linuxrealtime.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The W83627HF hardware monitoring features are supported by the
w83627hf driver for several years now. Support by the w83781d has
been advertised as deprecated 6 months ago, it's about time to see
it go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
It's about time to reflect the move of the lm-sensors project to
lm-sensors.org.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
It happens that the Analog Devices ADM1024 is fully compatible with
the National Semiconductor LM87, so support for the former can easily
be added to the lm87 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
We've never seen any device supported by the lm78 or w83781d driver at
addresses 0x20-0x27, so let's stop probing these addresses. Extra probes cost
time, and have potential for confusing or misdetecting other I2C devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Update the hwmon sysfs interface documentation to include a specification
for power meters.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for the SMSC SCH3112, SCH3114, and SCH3116 Super-I/O
chips. These chips feature identical hardware monitoring capabilites with the
expection that some of the fan inputs and pmw outputs don't exist.
The hardware monitoring features of the SCH311x chips can only be accessed via
the ISA bus. The driver therefore registers as a platform driver, if such a
chip is detected.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for the Celeron 4xx based on Core 2 core.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix a bug in the code examples, make them comply with CodingStyle,
and indent them for a better redability.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Here is a patch adding some text to the sysfs interface documentation on how
settings written to sysfs attributes should be handled, focussing mainly on
error handling. This version incorperates Jean's latest comments.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add individual alarm files to the lm78 driver, these are needed by
the next version of libsensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for the IT8716F and IT8718F fan4 and fan5. The late
revisions of the IT8712F have these too but support is harder to add
and nobody asked for it yet, so I didn't include it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add new sysfs alarm methodology to w83791d driver
Signed-off-by: Charles Spirakis <bezaur@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Document the name attribute.
* Document the *_label attributes.
* Drop "typical usage" lists, they no longer match the reality.
* Drop non hardware-monitoring related entries.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
* Drop documentation of generic module parameters.
* Drop redundant section "Driver Description".
* Drop sample configuration section, it belongs to sensors.conf.eg.
* Random spelling and punctuation fixes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Deprecate the use of thermistor beta values as thermal sensor types.
No driver supports changing the beta value anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The Fintek F71806F/FG is compatible with the F71872F/FG, so it is
already supported by the f71805f hardware monitoring driver. In fact,
both chips have the same chip ID, so the driver can't even
differentiate between them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The Analog Devices chip information pages moved to a different location.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for THMC50 and ADM1022 hardware monitoring chips.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The W83627EHF and similar chips have 6 VID input pins, add support
for them. The driver changes the input voltage level automatically
if the current setting is not correct for the detected CPU model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds support for the LM93 hardware monitoring chip.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The documentation of the pwmN_enable interface file is not very clear,
and has been confusing several driver authors already. Make it clearer.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for the "temperature mode" fan speed control. In this mode,
the user can define 3 temperature/speed trip points, and the chip will
set the speed automatically according to the temperature changes.
Signed-off-by: Phil Endecott <kernel@chezphil.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds the SMSC SCH5317 chip (device ID 0x85) as a supported
device to the smsc47b397 driver.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for IT8726F chip driver, which is just same as
IT8716F with additional glue logic for AMD power sequencing.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have the following naming convention documented in
Documentation/hwmon/sysfs-interface for fault files:
in[0-*]_input_fault
fan[1-*]_input_fault
temp[1-*]_input_fault
Some drivers follow this convention (lm63, lm83, lm90, smsc47m192).
However some drivers omit the "input" part and create files named
fan1_fault (pc87427) or temp1_fault (dme1737). And the new "generic"
libsensors follows this second (non-standard) convention, so it fails
to report fault conditions for drivers which follow the standard.
We want a single naming scheme, and everyone seems to prefer the
shorter variant, so let's go for it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add documentation for the new SMSC DME1737 driver.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert files within the Documentation directory to UTF-8.
Adrian Bunk:
small additional fixes
Signed-off-by: John Anthony Kazos Jr. <jakj@j-a-k-j.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This driver supports the Maxim MAX6650 and MAX6651 fan speed
monitoring and control chips.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new SMSC LPC47M292 Super-I/O chip is a bit different from the
previous ones, it supports a 3rd fan, but unfortunately the pin
configuration registers are different.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The new SMSC LPC47M292 Super-I/O chip includes a hardware monitoring
block which is compatible with those of the LPC47M192.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hartmut Rick <linux@rick.claranet.de>
Let the user select the base PWM frequency when using the it87
hardware monitoring driver. Different frequencies can give better
control on some fans.
Also update the documentation to mention the PWM frequency control
files, with misc cleanups to the PWM section.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ignore the temperature readings when its channel is disabled,
ignore AMDSI readings.
Signed-off-by: Gong Jun <jgong@winbond.com>
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Documentation for the new w83793 hardware monitoring driver, originally
provided by Yuan My from Winbond.
Also add myself as the maintainer of this driver.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Fintek F71872F/FG Super-I/O chip. It is basically the
same as the Fintek F71805F/FG as far as hardware monitoring is concerned,
with two additional internal voltages monitored (VSB and battery), and 6
VID inputs (not yet supported.)
To make things a bit more confusing, two of the voltage input pins (in4
and in8) can be used for other functions. The driver reads the pin
configuration from the Super-I/O configuration space to decide whether
it must create interface files for these inputs or not.
Many thanks to Nikolay Derkach for testing the early iterations of this
code and reporting bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a new hardware monitoring driver for the National Semiconductor
PC87427 Super-I/O chip. It only supports fan speed monitoring for now,
while the chip can do much more.
Thanks to Amir Habibi at Candelis for setting up a test system, and to
Michael Kress for testing several iterations of this driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This interface was useless as the LPC ISA-like interface is always
available, is faster, and is more reliable. This cuts the driver
size by some 20%.
This change is also required to later convert the it87 driver to a
platform driver, so that we can get rid of i2c-isa in a near future.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update the documentation for the k8temp driver.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SMSC LPC47M112 Super-I/O chip appears to be compatible with the
LPC47M10x and LPC47M13x as far as hardware monitoring is concerned.
The device ID is even the same, so it's really only a documentation
update.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace a bouncing email that I cannot recover from Mr Google.
Signed-off-by: Grant Coady <gcoady.lk@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hwmon: Remove Yuan Mu's address
Yuan Mu no longer works at Winbond.
I wish to publicly thank Yuan for his help with Winbond hardware
monitoring chips support during the past 10 months.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vt1211: Document module parameters
Add a description of the module parameters to the documentation of
the vt1211 driver.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
w83791d: Documentation update
The alarm bits and the beep enable bits are in different positions in
the hardware. Document the problem and leave it to the user-space code
to handle the situation. When this driver is updated to the standardized
sysfs alarm/beep methodology, this won't be a problem.
This is a documentation only change.
Signed-off by: Charles Spirakis <bezaur@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
k8temp: Add documentation
Add promised documentation for the k8temp driver.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Copyright update
I think my contributions to the it87 driver over the past two
years qualify me as a co-author of this driver.
Also drop old comments of dubious usefulness.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Add support for the IT8718F
The IT8718F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8716F, so adding support to the
it87 driver was pretty straightforward. The most significant difference
is that the IT8718F has up to 8 VID pins, instead of 6 for the older
chips.
For the IT8718F, the VID value can only be read from Super-I/O space.
Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Add support for the IT8716F
The IT8716F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8712F, so adding support to the
it87 driver was pretty straightforward. The most significant change here
is that the IT8716F has 16-bit fan speed counters, so the user no more
needs to tweak the fan clock dividers to get the best readings.
Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Thanks to Stian Oksavik, Olivier Nicolas, Prakash Punnoor and
Juergen Kilb for testing the early versions of this patch.
Thanks also to ITE for providing datasheets and answering my questions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add documentation for the w83627ehf hardware monitoring driver.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation update for the new bank1_types module param.
Also add what we know about different revisions of the uGuru and
a note that the abituguru driver unfortunatly does not work with the
latest and greatest motherboards, which have what I think is revision
4 of the uGuru.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements support for the National Semiconductor LM70
temperature sensor.
The LM70 temperature sensor chip supports a single temperature sensor.
It communicates with a host processor (or microcontroller) via an
SPI/Microwire Bus interface.
Communication with the LM70 is simple: when the temperature is to be sensed,
the driver accesses the LM70 using SPI communication: 16 SCLK cycles
comprise the MOSI/MISO loop. At the end of the transfer, the 11-bit 2's
complement digital temperature (sent via the SIO line), is available in the
driver for interpretation. This driver makes use of the kernel's in-core
SPI support.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New hardware monitoring driver for the Abit uGuru
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reword and complete certain parts of the hwmon sysfs-interface
documentation file. Hopefully this will make things clearer for new
driver authors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up hwmon sysfs documentation file, plus introduces
the description of DC/PWM selection for fan speed control.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improve the help text for CONFIG_HWMON to let the users know how they
pick the right hardware monitoring driver(s) for their system.
Also fix a couple typos in the related documentation file and improve
some parts a bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One more motherboard confirmed to have an LM83 temperature sensor chip.
Thanks to Steven Hardy for reporting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the w83791d sensor chip. The w83791d hardware is
somewhere between the w83781d and the w83792d and this driver code
is derived from the code that supports those chips.
Signed-off-by: Charles Spirakis <bezaur@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extend the sysfs interface of hardware monitoring chips, by adding
individual alarm and beep files. Contrary to the old aggregated "alarms"
and "beeps" files, individual files constitute a standard way to access
the status information, making it finally possible to implement a
chip-independant hardware monitoring chip access library (once all
drivers have been added this new interface, that is.)
If future drivers need more individual files, the interface will be
extended as needed at the same time these drivers are merged into the
kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver (smsc47m192) which supports voltage and temperature
measurement features of SMSC LPC47M192 and LPC47M997 chips.
Signed-off-by: Hartmut Rick <linux@rick.claranet.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add LM82 temperature sensor support (similar to the LM83,
but less featureful).
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop resetting the chip on load by default, so as to preserve the BIOS
initializations. Same was done in the w83627hf driver some times ago
for the same reasons.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Document the individual alarm and beep bits of the w83781d driver.
Ideally we would offer a chip-independant interface for them, but
until it's done, it's only fair that we document the current
interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Winbond W83687THF chip to the w83627hf hardware
monitoring driver. This new chip is almost similar to the already
supported W83627THF chip, except for VID and a few other minor
changes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Document the reset module parameter which was recently added to the
w83627hf driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only scan I2C address 0x2d. This is the default address and no IT87xxF
chip was ever seen on I2C at a different address. These chips are
better accessed through their ISA interface anyway.
This fixes bug #5889, although it doesn't address the whole class
of problems. We'd need the ability to blacklist arbitrary I2C addresses
on systems known to contain I2C devices which behave badly when probed.
Plan the I2C interface for removal as well. If nobody complains within
a year, it will confirm my impression that the I2C interface isn't
actually needed by anyone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is my f71805f hardware monitoring driver ported from lm_sensors
to Linux 2.6. This new driver differs from the other hardware monitoring
drivers in that it is implemented as a platform driver. This might not
be optimal yet (we would probably need a generic infrastructure and bus
type for Super-I/O logical devices) but it is certainly much better than
the i2c-isa solution.
Note that this driver requires lm_sensors CVS. I hope to get it
released as 2.10.0 soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add some documentation for the new f71805f driver. This is almost the
same help that was present in lm_sensors, with a few minor layout fixes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch clarifies the W83627THF VID documentation.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SMSC LPC47M997 Super-I/O chip seems to be compatible with the
LPC47M192, so it is supported by the smsc47m1 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the I2C addresses for the ADM1032 and ADT7461 chips.
Also update the links to the Analog Devices web site.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PEC support to the lm90 driver. Only the ADM1032 chip supports it,
and in a rather tricky way, which is why this patch comes with
documentation reinforcements. At least, this demonstrates that the new
PEC support logic in i2c-core can properly deal with chips with partial
PEC support.
As enabling PEC causes a significant performance drop, it can be
disabled through a sysfs file (unsurprisingly named "pec").
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new ID to the SMSC LPC47B397-NC hardware
monitoring driver - for a chip that is claimed to be 100%
compatible otherwise.
Signed-off-by: Bryan Young (Utilitek Systems, Inc.)
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop legacy ISA address support from the it87 driver. All supported
chips are Super-I/O chips, so the device ISA address can be safely read
from Super-I/O space rather than blindly assumed.
Two nearby inaccurate documentation statements have been fixed as well:
* The IT8705F doesn't have an SMBus interface.
* The SiS950 doesn't have a distinct prefix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not enable the VIA VT82C686A/B integrated sensors by default, as
disabled sensors usually means that this feature is not used so the
values won't make any sense. This has been confusing many users in the
past:
http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1786http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1811http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=2052
It is still possible to forcibly enable the sensors by using the
force_addr module parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation/hwmon/via686a | 17 +++++++++++++++--
drivers/hwmon/via686a.c | 18 +++++++++++-------
2 files changed, 26 insertions(+), 9 deletions(-)
This patch adds documentation entry for W83792D chip.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop the separate client name for the LM78-J chip. This is really
only a later revision of the LM78, with almost no difference and
no difference the driver handles in any case.
This was the only client name that had a dash in it, and special care
had to be taken in libsensors because of it. As we plan to write a new
library soon, I'd like to get rid of this exception before we do.
As a nice side effect, it saves 876 bytes in lm78.ko.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Part 3: Move the drivers documentation, plus two general documentation
files.
Note that the patch "adds trailing whitespace", because it does move the
files as-is, and some files happen to have trailing whitespace.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare