This fixes the following checkpatch.pl errors:
ERROR: code indent should use tabs where possible
+^I if (ptp->pps_source)$
ERROR: code indent should use tabs where possible
+^I pps_unregister_source(ptp->pps_source);$
ERROR: code indent should use tabs where possible
+^I kthread_destroy_worker(ptp->kworker);$
Fixes: 4225fea1cb ("ptp: Fix possible memory leak in ptp_clock_register()")
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'vclock_index' is accessed from sysfs, it shouled be freed
in release function, so move it from ptp_clock_unregister()
to ptp_clock_release().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff88800906c618 (size 8):
comm "i2c-idt82p33931", pid 4421, jiffies 4294948083 (age 13.188s)
hex dump (first 8 bytes):
70 74 70 30 00 00 00 00 ptp0....
backtrace:
[<00000000312ed458>] __kmalloc_track_caller+0x19f/0x3a0
[<0000000079f6e2ff>] kvasprintf+0xb5/0x150
[<0000000026aae54f>] kvasprintf_const+0x60/0x190
[<00000000f323a5f7>] kobject_set_name_vargs+0x56/0x150
[<000000004e35abdd>] dev_set_name+0xc0/0x100
[<00000000f20cfe25>] ptp_clock_register+0x9f4/0xd30 [ptp]
[<000000008bb9f0de>] idt82p33_probe.cold+0x8b6/0x1561 [ptp_idt82p33]
When posix_clock_register() returns an error, the name allocated
in dev_set_name() will be leaked, the put_device() should be used
to give up the device reference, then the name will be freed in
kobject_cleanup() and other memory will be freed in ptp_clock_release().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: a33121e548 ("ptp: fix the race between the release of ptp_clock and cdev")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a86ed2cfa1 ("ptp: Don't print an error if ptp_kvm is not supported")
fixes the error message print on ARM platform by only concerning about
the case that the error returned from kvm_arch_ptp_init() is not -EOPNOTSUPP.
Although the ARM platform returns -EOPNOTSUPP if ptp_kvm is not supported
while X86_64 platform returns -KVM_EOPNOTSUPP, both error codes share the
same value 95.
Actually kvm_arch_ptp_init() on X86_64 platform can return three kinds of
errors (-KVM_ENOSYS, -KVM_EOPNOTSUPP and -KVM_EFAULT). The problem is that
-KVM_EOPNOTSUPP is masked out and -KVM_EFAULT is ignored among them.
This patch fixes this by returning them to ptp_kvm_init() respectively.
Signed-off-by: Kele Huang <huangkele@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting
a new value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change
event notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup
on device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly
respond to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it
only in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xzZg
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from xfrm, bpf, netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting a new
value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with
nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change event
notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup on
device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly respond
to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it only
in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic"
* tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
net: prefer socket bound to interface when not in VRF
iavf: fix double unlock of crit_lock
i40e: Fix freeing of uninitialized misc IRQ vector
i40e: fix endless loop under rtnl
dt-bindings: net: dsa: marvell: fix compatible in example
ionic: move filter sync_needed bit set
gve: report 64bit tx_bytes counter from gve_handle_report_stats()
gve: fix gve_get_stats()
rtnetlink: fix if_nlmsg_stats_size() under estimation
gve: Properly handle errors in gve_assign_qpl
gve: Avoid freeing NULL pointer
gve: Correct available tx qpl check
unix: Fix an issue in unix_shutdown causing the other end read/write failures
net: stmmac: trigger PCS EEE to turn off on link down
net: pcs: xpcs: fix incorrect steps on disable EEE
netlink: annotate data races around nlk->bound
net: pcs: xpcs: fix incorrect CL37 AN sequence
net: sfp: Fix typo in state machine debug string
net/sched: sch_taprio: properly cancel timer from taprio_destroy()
net: bridge: fix under estimation in br_get_linkxstats_size()
...
The driver can't be loaded automatically because it misses
module alias to be provided. Add corresponding MODULE_DEVICE_TABLE()
call to the driver.
Fixes: 863d08ece9 ("supports eg20t ptp clock")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmFXQUoUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMglgf/egh3zb9/+BUQWe0xWfhcINNzpsVk
PJtiBmJc3nQLbZbTSLp63rouy1lNgR0s2DiMwP7G1u39OwW8W3LHMrBUSqF1F01+
gntb4GGiRTiTPJI64K4z6ytORd3tuRarHq8TUIa2zvki9ZW5Obgkm1i1RsNMOo+s
AOA7whhpS8e/a5fBbtbS9bTZb30PKTZmbW4oMjvO9Sw4Eb76IauqPSEtRPSuCAc7
r7z62RTlm10Qk0JR3tW1iXMxTJHZk+tYPJ8pclUAWVX5bZqWa/9k8R0Z5i/miFiZ
glW/y3R4+aUwIQV2v7V3Jx9MOKDhZxniMtnqZG/Hp9NVDtWIz37V/U37vw==
=zQQ1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm fixes from Paolo Bonzini:
"Small x86 fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: Ensure all migrations are performed when test is affined
KVM: x86: Swap order of CPUID entry "index" vs. "significant flag" checks
ptp: Fix ptp_kvm_getcrosststamp issue for x86 ptp_kvm
x86/kvmclock: Move this_cpu_pvti into kvmclock.h
selftests: KVM: Don't clobber XMM register when read
KVM: VMX: Fix a TSX_CTRL_CPUID_CLEAR field mask issue
hv_clock is preallocated to have only HVC_BOOT_ARRAY_SIZE (64) elements;
if the PTP_SYS_OFFSET_PRECISE ioctl is executed on vCPUs whose index is
64 of higher, retrieving the struct pvclock_vcpu_time_info pointer with
"src = &hv_clock[cpu].pvti" will result in an out-of-bounds access and
a wild pointer. Change it to "this_cpu_pvti()" which is guaranteed to
be valid.
Fixes: 95a3d4454b ("Switch kvmclock data to a PER_CPU variable")
Signed-off-by: Zelin Deng <zelin.deng@linux.alibaba.com>
Cc: <stable@vger.kernel.org>
Message-Id: <1632892429-101194-3-git-send-email-zelin.deng@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change prevents from users to access device before devlink is
fully configured.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rsmu (Renesas Synchronization Management Unit ) driver is located in
drivers/mfd and responsible for creating multiple devices including
clockmatrix phc, which will then use the exposed regmap and mutex
handle to access i2c/spi bus.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_COMMON_CLK, this fails to link:
arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_register_i2c':
ptp_ocp.c:(.text+0xcc0): undefined reference to `__clk_hw_register_fixed_rate'
arm-linux-gnueabi-ld: ptp_ocp.c:(.text+0xcf4): undefined reference to `devm_clk_hw_register_clkdev'
arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_detach':
ptp_ocp.c:(.text+0x1c24): undefined reference to `clk_hw_unregister_fixed_rate'
Fixes: a7e1abad13 ("ptp: Add clock driver for the OpenCompute TimeCard.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns twice:
drivers/ptp/ptp_ocp.c:2065:16: error: operator '?:' has lower precedence
than '&'; '&' will be evaluated first
[-Werror,-Wbitwise-conditional-parentheses]
on & map ? " ON" : "OFF", src);
~~~~~~~~ ^
drivers/ptp/ptp_ocp.c:2065:16: note: place parentheses around the '&'
expression to silence this warning
on & map ? " ON" : "OFF", src);
^
( )
drivers/ptp/ptp_ocp.c:2065:16: note: place parentheses around the '?:'
expression to evaluate it first
on & map ? " ON" : "OFF", src);
^
on and map are both booleans so this should be a logical AND, which
clears up the operator precedence issue.
Fixes: a62a56d04e ("ptp: ocp: Enable 4th timestamper / PPS generator")
Link: https://github.com/ClangBuiltLinux/linux/issues/1457
Suggested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/r/20210917045204.1385801-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following process is used to read the PHC clock and correlate
the reading with the "correct" system time.
- get starting timestamp
- issue PCI write command
- issue PCI read command
- get ending timestamp
- read latched sec/nsec registers
The write command is posted to PCI bus and returns. When the write
arrives at the FPGA, the PHC time is latched into the sec/nsec registers,
and a flag is set indicating the registers are valid. The read command
returns this flag, and the time retrieval proceeds.
Below is a non-scaled picture of the timing diagram involved. The
PHC time corresponds to some SYS time between [start, end]. Userspace
usually uses the midpoint between [start, end] to estimate the PCI
delay and match this with the PHC time.
[start] | |
write |-------+ |
| \ |
read |----+ +----->|
| \ * PHC time latched into register
| \ |
midpoint | +------->|
| |
| |
| +----|
| / |
|<--------+ |
[end] | |
As the diagram indicates, the PHC time is latched before the midpoint,
so the system clock time is slightly off the real PHC time. This shows
up as a phase error with an oscilliscope.
The workaround here is to provide a tunable which reduces (shrinks)
the end time in the above diagram. This in turn moves the calculated
midpoint so the system time and PHC time are in agreemment.
Currently, the adjustment reduces the end time by 3/16th of the entire
window. E.g.: [start, end] ==> [start, (end - (3/16 * end)], which
produces reasonably good results.
Also reduce delays by just writing to the clock control register
instead of performing a read/modify/write sequence, as the contents
of the control register are known.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of adjtime uses gettime/settime to
perform nanosecond adjustments. This introduces addtional phase
errors due to delays.
Instead, use the FPGA's ability to just apply the nanosecond
adjustment to the clock directly.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A 4th timestamper is added which timestamps the output of the PHC.
The clock nanosecond offset is not always zero, so when compared
to other timestampers, this provides precise measurements.
Also, the timestamper interrupt from the PHC can be used to generate
a PPS signal for /dev/pps.
Also allow PTP_CLK_REQ_PEROUT requests for a 1PPS output, but do
not actually configure any output pins, this is done via sysfs.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming boards may have a second GNSS receiver, getting information
from a different constellation than the first receiver, which provides
some measure of anti-spoofing.
Expose the sysfs attribute for this device, if detected.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecard can provide a NMEA-1083 ZDA (time and date) output
string on a serial port, which can be used to drive other devices.
Add the NMEA resources, and the serial port as a sysfs attribute.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a view into the timecard internals for debugging.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On startup, parts of the FPGA need to be initialized - break these
out into their own functions, separate from the purely informational
blocks.
On startup, distrbute the UTC:TAI offset from the NMEA GNSS parser,
if it is available.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRIG and DCF output time in UTC, but the timecard operates
on TAI internally. Add an attribute node which allows adding
an offset to these modes before output.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRIG-B has several different output formats, the timecard defaults
to using B007. Add a control which selects different output modes.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRIG (Inter-range Instrumentation Group) timecode format on
one of the SMA output channels is provided by the IRIG master
FPGA block. Enable the master when the IRIG output format is
selected on either one of the output channels.
By default, the output is in B007 format.
DCF output format is provided by the DCF master block.
Also enable the IRIG and DCF slaves, which parse an incoming
signal from the external SMA connectors, and may be used to
adjust the PHC.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest firmware for the TimeCard adds selectable signals for
the SMA input/outputs. Add support for SMA selectors, and the
GPIO controls needed for steering signals.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware may provide a third signal timestamper, so make it
available for use.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a resource could not be registered, report the name of
the resource and the error code.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TimeCard exposes different resources, which may have their
own irqs. Space for the irqs is allocated through a MSI or MSI-X
interrupt vector. On some platforms, the interrupt allocation
fails.
Rather than making this fatal, just skip exposing those resources.
The main timecard functionality (that of a PTP clock) will work
without the additional resources.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an I2C controller isn't present, don't try and read the I2C flash.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only display the TOD information if there is a corresponding
TOD resource.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the xilinx i2c driver parameters to the resource block instead
of hardcoding things in the registration functions.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also correct how initialize_dco_operating_mode is called
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we don't need to support new 5.2 functions but different register
addresses
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not need since TCS firmware file will configure it properlly.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the 'imply' statements, these apparently are not doing
what I expected. Platform modules which are used by the driver
still need to be enabled in the overall config for them to be
used, but there isn't a hard dependency on them.
Use 'depend' for selectable modules which provide functions
used directly by the driver.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET doesn't imply NET_DEVLINK. Select this separately, so that
random config combinations don't complain.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 773bda9649 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If ptp_ocp_device_init() fails, pci_disable_device() is skipped.
Fix the error handling so this case is covered. Update ptp_ocp_remove()
so the normal exit path is identical.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 773bda9649 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If attempting to flash the firmware with a blob of size 0,
the entire write loop is skipped and the uninitialized err
is returned. Fix by setting to 0 first.
Fixes: 773bda9649 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb0 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes possible leak of PTP virtual clocks.
The number of PTP virtual clocks to be unregistered is passed as
'u32', but the function that unregister the devices handles that as
'u8'.
Fixes: 73f37068d5 ("ptp: support ptp physical/virtual clocks conversion")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After writing an image blob to the flash memory, a reboot is required
to reload the FPGA. There is no versioning prsent in the FPGA image
file, so only a running version is available. The 'stored version'
was set to 'pending' in order to indicate a reboot was needed.
This isn't reliable, as the module could be unloaded/loaded, losing
the "reboot needed" indicator. Also, the devlink 'stored version'
information is designed to refer to the actual image version.
Unfortunately, there is no method to determine the flash image version
other than booting it, so remove the devlink stored version setting.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TimeCard has two FPGA images in the flash: the actual firmware,
and a manufacturing fallback version which is intended to act as a
loader in case the flash update failed.
Name these "fw" and "loader", which are reflected in devlink:
[root@timecard drv]# devlink dev info
pci/0000:04:00.0:
driver ptp_ocp
serial_number fc:c2:3d:2e:d7:c0
versions:
running:
fw 5
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPS is not the only available positioning system. Use the generic
naming of "GNSS" instead.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carlos Llamas